Search results for "tools"

XP-SRPMC1 Snap Ring Pliers Multi Crimp Removable Pliers Head

Read more less

XP-WSM1175 Wire Stripper

Read more less

WB-3XPL Miniature Brass, Nylon and Stainless Steel Brush Set

Read more less

ERP UVLIGHT LED UV Flashlight Batteries not included  California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

EXPTC105 Test Lead Set Set of 10 Wires 100% Brand new and high quality Color coded leads allow you to test circuits without crossing wires or causing shorts Can be used as low voltage jumper leads Test Leads with Alligator Clips Set Insulated Test Cable Double-ended Clips IMPORTANT! You should call ahead to confirm availability of an item before going to the store. store's actual inventory can change from minute to minute. Calling the store will allow you to confirm that the item is still available. Some items may not be immediately available for pickup at your local store. Prices and availability may differ from web prices at local pickup location.

Read more less

XPARTCO DC97-16350U Washer Suspension Rod Kit (Set of 4) The XPARTCO DC97-16350U is an aftermarket replacement washer suspension rod kit (set of 4) compatible with a wide range of Samsung top-load washers in the WA40, WA41, WA42, WA44, WA45, WA49, and WA50 series. The suspension rods are spring-loaded shock-absorbing rods that connect the outer washer tub to the top corners of the cabinet frame, suspending the tub and dampening the vibrations generated during agitation and high-speed spin cycles. When one or more rods lose tension, break, or degrade, the tub swings off-center and strikes the cabinet walls — causing violent shaking, loud banging, error code dc (out of balance), UE imbalance errors, and progressive damage to the machine. Each rod measures 26.4–26.5 inches in overall length and 1-1/4 inches in diameter, constructed from spring steel with plastic end caps. The kit includes all 4 suspension rods — always replace all four at the same time since they wear at the same rate. It directly replaces DC97-16350S, DC97-16350T, DC97-16350E, DC97-16350C, DC97-16350D, DC97-16350K, DC97-05280W, 4962798, AP6884450, EAP12720841, PS12720841, and PD00065434. Wear gloves during installation — the rods are coated with grease. Installs in 20–30 minutes — no special tools required. Quick Answer The XPARTCO DC97-16350U Washer Suspension Rod Kit fixes Samsung top-load washers that vibrate violently, bang loudly, walk across the floor, or display dc or UE imbalance error codes during spin. Set of 4 rods, 26.4–26.5" long, 1-1/4" diameter, spring steel with plastic end caps. Replace all 4 at the same time. Wear gloves — rods are greased. Compatible with Samsung WA40–WA50 series. Replaces DC97-16350S, DC97-16350T, DC97-16350E, DC97-16350C, DC97-16350D, AP6884450, PS12720841. Common Problems This Kit Fixes Washer vibrating violently or shaking excessively during the spin cycle Loud banging or thumping — tub striking the cabinet walls during spin Washer "walking" or moving across the floor during high-speed spin Error code dc displayed — Samsung out-of-balance error during spin Error code UE displayed — unbalanced load error the washer cannot self-correct Washer repeatedly stopping and rebalancing the load without completing the spin cycle Visible broken, detached, or sagging suspension rod inside the washer cabinet Rattling or clunking during agitation — tub no longer centered Replaces Part Numbers This suspension rod kit directly replaces the following OEM and cross-reference part numbers: DC97-16350U, DC97-16350S, DC97-16350T, DC97-16350E, DC97-16350C, DC97-16350D, DC97-16350J, DC97-16350K, DC97-16350U, DC97-16350E, DC97-16350S, DC97-16350C, DC97-16350D, DC97-16350T, AP6884450, ASM34747, EAP12720841, PD00065434, PS12720841. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This suspension rod kit is compatible with select top-load washers from the following Samsung series: Samsung WA40 series — WA400PJHDWR, WA40J3000AW, WA40A3005AW, WA44A3205AW and related models Samsung WA41 series — WA41A3000AW and related models Samsung WA42 series — WA422PRHDWR and related models Samsung WA45 series — WA45H7000AW, WA45H7200AW, WA45K7600AW, WA45M7050AW, WA45N3050AW, WA45T3200AW, WA45T3400AW, WA45T3400AP, WA456DRHDSU, WA456DRHDWR and related models Samsung WA49 series — WA49B5105AW, WA49B5205AW and related models Samsung WA50 series — WA50R5200AW, WA50R5400AV, WA50R5400AW, WA50T5300AC and related models Kenmore / Sears top-load washers (select Samsung-built models) Important: The DC97-16350U rod is 26.4–26.5 inches long and is for Samsung WA40–WA50 series washers. Larger-capacity WA48–WA54 series models use the longer DC97-16350V rod (27.5 inches). Always measure your existing rods or verify your model number before ordering — using the wrong length rod can cause the tub to sit at the incorrect height inside the cabinet. Key Features Set of 4 suspension rods — complete replacement covering all four tub mounting points Suspends and centers the outer tub within the cabinet — dampens agitation and spin vibration to prevent tub-to-cabinet contact Resolves Samsung error codes dc (out of balance) and UE (unbalanced load) Rod length: 26.4–26.5 inches overall; diameter: 1-1/4 inches Spring steel construction with plastic end caps — durable and corrosion resistant Rods are pre-coated with grease — wear work gloves during installation Replace all 4 rods at the same time — rods wear together and partial replacement results in uneven tub support No special tools required — installs in 20–30 minutes Replaces DC97-16350S, DC97-16350T, DC97-16350E, DC97-16350C, DC97-16350D, and over 15 additional cross-references Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number DC97-16350U Part Type Washer Suspension Rod and Spring Assembly Condition Aftermarket Replacement Application Samsung Top-Load Washers — WA40, WA41, WA42, WA44, WA45, WA49, WA50 series Quantity Set of 4 (replace all four rods at the same time) Rod Length 26.4–26.5 inches overall Rod Diameter 1-1/4 inches Material Spring steel / Plastic end caps Color Brass / Black / White / Pink Lubrication Pre-coated with grease — wear gloves during installation Error Codes Resolved dc (out of balance), UE (unbalanced load) Compatible Brands Samsung, Kenmore (Samsung-built) Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting — Wear Gloves Disconnect power and turn off the water supply before beginning. Wear work gloves throughout — the suspension rods are coated with grease. Remove the lid and the top panel (typically secured by screws under the lid hinge covers and at the rear corners). With the top panel removed, the four suspension rods are visible at the corners, each running from a mounting point on the tub rim up to a hook or bracket at the top corners of the cabinet frame. Note the orientation and attachment method of each rod before removing. Unhook the top of each rod from the cabinet bracket and lift the bottom cup off the tub mounting pin. Install each new DC97-16350U rod by seating the bottom cup onto the tub mounting pin and hooking the top over the cabinet bracket. Replace all four rods before reassembling. Reinstall the top panel and lid, restore power and water, and run a spin cycle to verify smooth, quiet, centered operation. Tools needed: Phillips screwdriver; no special tools required for the rods themselves. Frequently Asked Questions What is the difference between DC97-16350U and DC97-16350V? Both are Samsung top-load washer suspension rods, but they are different lengths for different washer capacity generations. The DC97-16350U is approximately 26.4–26.5 inches long and is used on mid-capacity Samsung WA40 through WA50 series washers. The DC97-16350V is approximately 27.5 inches long and is used on larger-capacity WA48 through WA54 series washers. Using the wrong length rod causes the tub to sit at the wrong height inside the cabinet, which can cause new imbalance issues. Always measure your existing rods or verify your model number before ordering. Why must I replace all 4 rods instead of just the broken one? All four suspension rods experience the same amount of wear over the same number of wash cycles. When one rod fails, the remaining three have experienced the same stress and fatigue and are likely to fail soon after. Replacing only the broken rod leaves three worn rods supporting the tub unevenly — this can cause continued vibration, accelerate wear on the new rod, and require a second repair shortly after. Replacing all four at the same time ensures even tub support, fully resolves the imbalance, and prevents a repeat repair. Do DC97-16350S, DC97-16350T, and DC97-16350E all cross to the DC97-16350U? Yes — DC97-16350S, DC97-16350T, DC97-16350E, DC97-16350C, and DC97-16350D are all cross-reference part numbers for the same Samsung suspension rod assembly used across different production runs of the same washer series. Samsung updates part number suffixes during production revisions. All of these numbers have the same 26.4–26.5" length and are interchangeable with the DC97-16350U. What do error codes dc and UE mean on Samsung washers? Error code dc on Samsung top-load washers indicates the machine has detected an out-of-balance condition and stopped spinning to prevent damage. Error code UE indicates an unbalanced load that the washer cannot self-correct by redistributing. Both codes can be caused by an overloaded or unevenly distributed laundry load — but if the errors occur consistently even with normal, balanced loads, worn or broken suspension rods are the most common mechanical cause. Replacing the rod kit resolves these errors in most cases. Is this an OEM or aftermarket part? This is an aftermarket replacement kit built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured from spring steel with plastic end caps to match the length and spring tension of the original DC97-16350U suspension rods. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

WP8577891 Genuine OEM Whirlpool Dryer High-Limit Thermostat The WP8577891 is a genuine Whirlpool OEM high-limit thermostat for Whirlpool, Maytag, Jenn-Air, Kenmore, KitchenAid, Amana, Magic Chef, Admiral, Norge, and Roper dryers. This part combines two functions in a single component: it acts as a safety mechanism that shuts off the heating element when the dryer overheats, and it includes an inlet thermistor that monitors the temperature of the inlet air feeding into the dryer. Rated L260-68F: the heating element cuts out once internal temperature reaches 260°F, and kicks back in once temperature drops to 192°F, a 68°F differential built into the design. Weighing approximately 0.08 lbs, with package dimensions of 4.33" x 3.43" x 0.79". Because this is a safety-critical component, a malfunctioning thermostat can shut off the dryer even when it isn't actually overheating, in addition to producing the more expected overheating symptom if it fails to trip when it should. Symptoms include the dryer overheating, blown thermal fuses, or the dryer shutting off unexpectedly during a cycle. It directly replaces 8577891, 314654, AP6013527, AWP48573, EAP11746753, OEM18040590, L260-68F, L126.7-37.7C, PD00003286, PS11746753. Quick Answer The WP8577891 Genuine OEM Whirlpool Dryer High-Limit Thermostat fixes Whirlpool, Maytag, Jenn-Air, Kenmore, KitchenAid, Amana, Magic Chef, Admiral, Norge, and Roper dryers with overheating, blown thermal fuses, or unexpected shutoffs during a cycle. L260-68F rating. Replaces 8577891, 314654, AP6013527, AWP48573, EAP11746753, OEM18040590, L260-68F, L126.7-37.7C, PD00003286, PS11746753. Test the old thermostat's continuity with a multimeter before ordering — one customer found this quick check would have confirmed the part was actually needed before they bought a replacement. Common Problems This Part Fixes Dryer overheating during a cycle Dryer blowing thermal fuses repeatedly Dryer shutting off unexpectedly, even when it doesn't seem to be overheating Dryer not heating properly due to a malfunctioning safety cutoff Irregular or inconsistent drying cycles Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer high-limit thermostat directly replaces the following OEM and cross-reference part numbers: WP8577891, 8577891, 314654, AP6013527, AWP48573, EAP11746753, OEM18040590, L260-68F, L126.7-37.7C, PD00003286, PS11746753 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This high-limit thermostat is compatible with select Whirlpool electric dryers, and also fits select Maytag, Jenn-Air, Kenmore, KitchenAid, Amana, Magic Chef, Admiral, Norge, and Roper dryers built on the Whirlpool platform, including model numbers such as MED6600TQ0, WED6200SW0, WED6200SW1, WED6600VU0, WED6600VW0, WED6600WL0, YMED6600TQ0, YWED6200SW1, YWED6600VU0, YWED6600VW0, and YWED6600WL0. Note: Always verify your full model number before ordering, since Whirlpool uses different high-limit thermostat designs across its dryer lineup. Contact our support team with your model number if you're unsure. Key Features Genuine Whirlpool OEM part — factory-specified opening and reset temperatures Combines high-limit thermostat and inlet thermistor functions in one component Resolves "overheating," "blown thermal fuses," and "unexpected shutoff mid-cycle" symptoms L260-68F rating — opens at 260°F Automatically resetting — no replacement needed after each trip Direct drop-in replacement matching the original mounting and terminal configuration Replaces 8577891, 314654, AP6013527, AWP48573, EAP11746753, OEM18040590, L260-68F, L126.7-37.7C, PD00003286, PS11746753 Compatible with Whirlpool, Maytag, Jenn-Air, Kenmore, KitchenAid, Amana, Magic Chef, Admiral, Norge, and Roper dryers Genuine OEM replacement — guaranteed fit, materials, and performance Approximately 30-minute repair Product Specifications Part Number WP8577891 Part Type Dryer High-Limit Thermostat with Inlet Thermistor Condition Genuine OEM Brand Whirlpool Rating L260-68F Type Automatically resetting Weight Approx. 0.08 lbs Package Dimensions 4.33" x 3.43" x 0.79" Repair Difficulty Easy — approx. 30 minutes Quantity 1 high-limit thermostat Compatible Brands Whirlpool, Maytag, Jenn-Air, Kenmore, KitchenAid, Amana, Magic Chef, Admiral, Norge, Roper Installation Notes ⚠️ Unplug Dryer Before Starting — Test With A Multimeter Before Assuming It's This Part Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Unscrew and remove the dryer's exhaust vent hose, then use a nut driver to remove the back panel. Locate the high-limit thermostat, typically mounted near the heating element housing. Before removing the old part, test it with a multimeter set to continuity — a healthy thermostat shows continuity; one that doesn't should be replaced. Photograph the wiring before disconnecting anything. Disconnect the wire terminals from the old thermostat, remove its mounting screw, and pull it free. Install the new WP8577891 in the same position, reconnect the wire terminals, and secure the mounting screw. Reattach the back panel and exhaust vent hose. Restore power and run a full test cycle to confirm normal, consistent heating with no premature shutoffs. Tools needed: nut driver, flat-head screwdriver, multimeter, work gloves. Frequently Asked Questions How do I know if this thermostat has actually failed before I order one? Test the old thermostat with a multimeter set to continuity before ordering — it's a simple, quick check. One customer specifically noted they wished they had tested the part first: they ordered a replacement, then discovered testing the old one with a multimeter was easy to do and would have confirmed whether they actually needed the new part before buying it. My dryer shuts off even though it doesn't feel like it's overheating. Could this still be the thermostat? Yes. A malfunctioning high-limit thermostat can shut off the dryer even when actual temperatures are normal, not just when the dryer is genuinely running too hot. If your dryer stops mid-cycle without an obvious overheating cause, this thermostat is worth testing. Should I replace other parts at the same time as this thermostat? If your dryer has also blown a thermal fuse, it's worth replacing the fuse and any related thermal cutoff components together with this thermostat, since they often fail from the same underlying overheating cause. Also check your exhaust venting for restrictions while you have the dryer open, since blocked airflow is a common root cause of repeated thermal component failures. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original opening and reset temperatures and mounting configuration of the high-limit thermostat originally installed in your dryer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

349241T Genuine OEM Dryer Drum Roller Kit - Compatible with Whirlpool, Kenmore, Maytag Restore smooth and quiet operation to your dryer with the 349241T Genuine OEM Dryer Drum Roller Kit. This Whirlpool-manufactured kit includes two drum rollers, four tri-rings, and one retaining washer, designed to support the drum in select Whirlpool, Kenmore, Maytag, and other compatible dryers. It addresses issues like excessive noise, vibration, or drum not tumbling, ensuring efficient drying performance. Recommended to replace both rollers at once for optimal results. This set includes 2 drum rollers, 4 tri-ring retaining clips, and 2 retaining washers — everything needed for a complete rear roller replacement. Each roller measures 3-1/4"L x 1"W x 3-1/4"H and is constructed from rubber over a metal bearing hub with a plastic axle support. Both rollers must always be replaced at the same time. The set directly replaces 349241, 349241TVP, 8170, 8205, 337089, 340352, 661562, 3389901, 3397588, 3397590, AP3098345, PS347627, and several additional cross-reference numbers. Often replaced together with the drum belt (341241) and idler pulley (691366 or 279640) for a complete drum drive repair. Installs in 30–60 minutes with basic hand tools. Quick Answer 349241T Genuine OEM Dryer Drum Roller Kit. This Whirlpool-manufactured kit includes two drum rollers, four tri-rings, and one retaining washer, designed to support the drum in select Whirlpool, Kenmore, Maytag, and other compatible dryers. It addresses issues like excessive noise, vibration, or drum not tumbling, ensuring efficient drying performance. Recommended to replace both rollers at once for optimal results. Replaces 349241, 8170, 8205, 337089, 3389901, AP3098345, PS347627. Common Problems This Part Fixes Loud thumping, rumbling, or squealing noise during the drying cycle Grinding or scraping sound when the drum is turning Drum turning unevenly or wobbling during operation Drum not spinning — rollers so worn they can no longer support the drum Squealing or squeaking that gets worse over time as roller bearings degrade Marks or scuff lines on clothes — drum dragging against the dryer cabinet Excessive vibration during the drying cycle Replaces Part Numbers This drum roller set directly replaces the following OEM and cross-reference part numbers: 349241T, 26000349241, 337089, 3389901, 3397588, 3397590, 340352, 3436, 349241, 349241TVP, 661562, 8170, 8205, 99989678, 99989679, AH347627, EA347627, K34-895, AWP39168, PD00002257, EAP347627, AP3098345, PS347627.  If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drum roller set is compatible with select 29-inch gas and electric dryers from the following brands: Whirlpool dryers (gas and electric — 29" models) Kenmore / Sears dryers (Whirlpool-built models) Maytag dryers KitchenAid dryers Amana dryers Roper dryers Crosley dryers Estate dryers Inglis dryers Admiral dryers Magic Chef dryers Note: The 349241T rollers are for 29-inch Whirlpool-family dryers. Newer Whirlpool Duet front-load dryers and larger-capacity models use different roller part numbers (such as WPW10314173 / 8536974). Always verify your model number before ordering. Key Features Set of 2 rear drum support rollers — supports and cradles the drum as it rotates for smooth, quiet operation Includes all hardware: 2 rollers, 4 tri-ring retaining clips, 2 retaining washers — everything needed for a complete installation Dimensions: 3-1/4"L x 1"W x 3-1/4"H per roller Rubber wheel over metal bearing hub with plastic axle support — designed to resist wear and heat under continuous drum load Both rollers must be replaced at the same time — replacing only one results in uneven drum support and accelerated wear on the new roller Often replaced together with the drum belt (341241) and idler pulley (691366 or 279640) for a complete drum drive repair Compatible with 11 major appliance brands on the Whirlpool 29-inch platform Dryer Genuine OEM Part. DIY repair — installs in 30–60 minutes with basic hand tools Product Specifications Part Number 349241T Part Type Dryer Rear Drum Support Roller Set Condition  Genuine Whirlpool OEM Application 29-inch Gas and Electric Dryers Quantity Set of 2 rollers (replace both at the same time) Roller Dimensions 3-1/4"L x 1"W x 3-1/4"H (per roller) Material Rubber wheel / Metal bearing hub / Plastic axle support Color Black / White Kit Includes 2 drum rollers, 4 tri-ring retaining clips, 2 retaining washers Often Replaced With 341241 Drum Belt, 691366 or 279640 Idler Pulley Compatible Brands Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Crosley, Estate, Inglis, Admiral, Magic Chef Installation Notes ⚠️ Unplug Dryer Before Starting Disconnect power (and shut off gas for gas dryers) before beginning. Remove the lint screen and unscrew the screws inside the lint screen housing. Use a putty knife to release the top panel spring clips and lift the top panel. Remove the front panel to access the drum. Release the drive belt from the idler pulley, lift the drum forward, and set it aside. The rear drum support rollers are mounted on shafts on the rear bulkhead — each roller is secured with a tri-ring clip and a retaining washer. Use needle-nose pliers to remove the old tri-ring clips, then slide the old rollers off the shafts. Install the new rollers, new retaining washers, and new tri-ring clips on the shafts. Reinstall the drum, re-route the belt around the motor and idler pulley, and reassemble the front and top panels. Restore power and run a test cycle to verify quiet, smooth drum operation. Tip: while the dryer is open, inspect and replace the drum belt (341241) and idler pulley (691366 or 279640) if worn. Tools needed: Phillips screwdriver, 1/4" or 5/16" nut driver, putty knife, needle-nose pliers. Frequently Asked Questions What do the drum support rollers do? The rear drum support rollers are cylindrical wheels mounted on fixed shafts at the back of the dryer cabinet. As the drum rotates, its rear outer rim rests on these rollers, which carry the drum's weight and allow it to spin smoothly and quietly. When the rubber wheels wear down or the bearing hubs corrode, the drum no longer rides smoothly on the rollers — causing thumping, rumbling, or squealing noises that get progressively worse. In severe cases, worn rollers allow the drum to sag and drag against the cabinet rear panel. Why must I replace both rollers at the same time? Both rear drum support rollers carry the same load and experience the same wear through every drying cycle. When one roller fails, the other has been under the same stress for the same number of cycles and is almost certainly near the end of its useful life. Replacing only the failed roller leaves one worn roller supporting the drum unevenly, which puts extra stress on the new roller and causes it to wear out much faster. Replace both rollers at the same time to ensure even drum support and get the full service life from the new parts. Should I also replace the belt and idler pulley at the same time? Yes — this is the ideal time. Since the dryer must be fully disassembled to access the rear drum rollers, replacing the drum belt (341241) and idler pulley (691366 or 279640) at the same time is strongly recommended. All three parts wear at similar rates, and a worn belt or idler pulley is often what caused the rollers to wear prematurely. Doing all three in one repair eliminates the most common drum drive failure points and saves you from repeating the teardown in the near future. The 4392065 maintenance kit includes all three parts together. What causes dryer drum rollers to wear out? Drum rollers wear naturally over time from the continuous load of supporting the rotating drum. The most common accelerating factors are operating the dryer with a worn or broken belt (which allows the drum to sag and puts extra weight on the rollers), running very large or heavy loads frequently, and allowing lint to accumulate around the roller shafts, which causes the bearings to run dry and wear faster. Regular dryer maintenance — including cleaning lint from around the drum and periodically checking the belt — helps extend roller life. Is this an OEM or aftermarket part? It is a genuine Whirlpool OEM part. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

S48D21 8" Range Surface Element Product Title Aftermarket S48D21 8" Range Surface Element - Compatible with Whirlpool, Maytag, Kenmore, Jenn-Air, Amana Electric Ranges Product Description Revive your electric range’s cooking performance with the Aftermarket S48D21 8" Range Surface Element from Parts-O-Matic. This high-quality aftermarket burner element replaces the original S48D21, delivering 2100 watts at 240V with a 4-turn coil design for efficient and even heating. Ideal for select Whirlpool, Maytag, Kenmore, Jenn-Air, Amana, and other brand electric ranges, it addresses issues like uneven heating, slow warm-up, or non-functional burners. Enjoy free shipping on all orders at Parts-O-Matic! Key Features: ✅ Broad Compatibility: Fits select Whirlpool, Maytag, Kenmore, Jenn-Air, Amana, and other electric range models. 🔥 Efficient Heating: 8" diameter, 4-turn coil delivers 2100 watts at 240V for consistent, even cooking. 💰 Cost-Effective Alternative: Aftermarket part offers OEM-equivalent performance at a lower price. 🛠️ Easy Installation: Plug-in design with Y-style bracket; requires no tools and takes 5–10 minutes to install. 🛡️ Fixes Common Issues: Resolves uneven heating, slow warm-up, or burners that fail to heat. Compatibility: Compatible with models including but not limited to: Whirlpool: RF110AXSQ0, RF262LXSB, RF365PXKW0 Maytag: MER4110AAH, MER4120AAQ Kenmore: 629.4297, 629.60003600 (pre-2004 models) Jenn-Air: JES9750AAB Amana: AER5511AAQ Replaces part numbers: TJ90SP21MA, 14215226, 1938283, 309917, 403782, 404110, 406000, 814154, ERS48D21, SE302, SP21MA, SU214, SU302, TS4D8221, TS4D8221PB, TS4D8221SR, TS4D8221WI, YSP21MA, AP4503257. Verify compatibility with your appliance brand and model number, please contact Parts-O-Matic support for assistance. Installation Notes: Tools Needed: None for standard installation; a flathead screwdriver may help for stubborn connections. Safety First: Unplug the range before installation to avoid electrical shock. Steps: Remove the old burner element by gently pulling it from the receptacle, align the Y-style bracket of the new S48D21 element, and plug it into the socket. Ensure the element sits flat in the drip pan. If the burner is not level, adjust the connection bolts to ensure they are parallel and push down gently. Installation takes 5–10 minutes. Note: A slight burning smell during first use is normal due to a protective coating; this will dissipate after 15–20 minutes. Download our installation guide or watch our YouTube tutorial for step-by-step instructions. Shop Parts-O-Matic for high-quality aftermarket appliance parts with free shipping on all orders and a 30-day return policy. Restore your range’s cooking performance today! Add to cart now for an affordable fix with free shipping on your entire order!

Read more less

W11130362 Washer Genuine OEM Suspension Rod Kit 23-1/2" overall length. The pack includes four dampers. Fits Specific Whirlpool 4.5 CF top load washer models. Replaces Part numbers: W11130362, W11027174, W10780040, W10594080, W10735786, W10748956, W10821710, W10901056, W11033491, W11228718, AP6262443, PS12347546. 🛠️ W11130362 Washer Genuine OEM Suspension Rod Kit Stop the shaking. Start the cleaning. The W11130362 Suspension Rod Kit is a genuine OEM replacement designed to stabilize your washer tub and eliminate excessive vibration during spin cycles. If your washer is banging, off-balance, or “walking” across the floor, worn suspension rods are the likely cause. This easy-to-install kit restores proper balance and extends the life of your machine. ✅ Key Features: Genuine OEM Quality – Factory-approved replacement for W11130362 Vibration Control – Dampens movement for a smooth spin cycle Includes All 4 Suspension Rods – Complete kit for a full fix DIY Installation – No special tools required Compatible with Whirlpool, Maytag, Amana, and more 🔍 Common Washer Issues This Fixes: Excessive noise or banging during spin Off-balance or unsteady drum Washer “walking” or shifting position Poor spinning or water left in clothes 💡 Why Buy from Parts-O-Matic?We carry only 100% genuine OEM parts—no substitutes. With fast shipping, verified fit, and expert customer service, Parts-O-Matic helps you fix it fast and fix it right the first time. 📦 Replaces Part Numbers: W11130362, W11027174, W10780040, W10594080, W10735786, W10748956, W10821710, W10901056, W11033491, W11228718, AP6262443, PS12347546. 🧰 Fits Brands & Models: Whirlpool Maytag Amana Admiral Roper Not sure if it fits your washer model? Contact us — we’ll help you match the right part!

Read more less