Refrigerator Fan Motors, Condenser & Evaporator and Fan Blades

WR60X25858 Freezer Genuine OEM Evaporator Fan Motor The WR60X25858 is a genuine GE OEM freezer evaporator fan motor for GE refrigerators, and also fits select Hotpoint, Haier, Monogram, Café, Profile, and Kenmore models. Located in the freezer compartment, this motor circulates air across the evaporator coil and out into the freezer and, on many models, the fresh food compartment, drawing heat out of the air to maintain consistent, efficient cooling throughout the appliance. Rated 13.6V DC, 0.23 amps, with fan dimensions of approximately 4.5" x 4.5" and a wiring harness and plug extending about 8.25" from the frame. Common causes of failure include worn motor bearings or electrical failure over time. Symptoms of a failing evaporator fan motor include the freezer failing to cool properly and warming up, insufficient airflow, excessive frost buildup, higher-than-normal freezer temperatures, or unusual noise — often caused by frost or ice rubbing against the fan blade as it turns. It directly replaces 239D1371P002, 3033253, 4931166, U11P14MS7AA3-57A61, WR60X10340, AGE29632, AP6891698, EAP12727431, EAP7320382, PD00054264, PS12727431. Quick Answer The WR60X25858 Freezer Genuine OEM Evaporator Fan Motor fixes GE, Hotpoint, Haier, Monogram, Café, Profile, and Kenmore refrigerators with a freezer that's warming up, insufficient airflow, excessive frost, or unusual noise from the fan area. 13.6V DC, 0.23A, ~4.5" x 4.5", 8.25" harness. Replaces 239D1371P002, 3033253, 4931166, AP5669723, AP6891698, EAP12727431, EAP7320382, PS12727431, PS7320382, U11P14MS7AA3-57A61, WR60X10340, AGE29632. If your freezer isn't cold, check the evaporator fan first — but while you're in there, cleaning frost or ice off the fan blade and vacuuming the condenser coils are worthwhile companion steps. Common Problems This Part Fixes Freezer not cooling properly, warming up Insufficient airflow through the freezer compartment Excessive frost buildup Higher-than-normal freezer temperatures Unusual noise from the fan area, including frost or ice rubbing on the blade Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This freezer evaporator fan motor directly replaces the following OEM and cross-reference part numbers: 239D1371P002, 3033253, 4931166, U11P14MS7AA3-57A61, WR60X10340, AGE29632, AP6891698, EAP12727431, EAP7320382, PD00054264, PS12727431 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This evaporator fan motor is compatible with select GE refrigerators, and also fits select Hotpoint, Haier, Monogram, Café, Profile, and Kenmore refrigerators built on the GE platform, including model numbers such as DFE29JSDFSS and DFE29JGDAWW. Note: GE uses several different evaporator fan motors across its refrigerator lineup, including WR60X26866 and WR60X26033 for other models. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which motor your refrigerator needs. Key Features Genuine GE OEM part — factory-specified motor design and airflow rating Circulates air across the evaporator coil to draw heat out and cool the freezer Resolves "freezer warming up," "insufficient airflow," "excessive frost," and "unusual noise" symptoms Rated 13.6V DC, 0.23 amps Approximately 4.5" x 4.5", with an 8.25" wiring harness and plug Direct drop-in replacement matching the original mounting and connections Replaces 239D1371P002, 3033253, 4931166, U11P14MS7AA3-57A61, WR60X10340, AGE29632, AP6891698, EAP12727431, EAP7320382, PD00054264, PS12727431 Compatible with GE, Hotpoint, Haier, Monogram, Café, Profile, and Kenmore refrigerators Genuine OEM replacement — guaranteed fit, materials, and performance DIY-friendly repair, typically 15 to 30 minutes Product Specifications Part Number WR60X25858 Part Type Freezer Evaporator Fan Motor Condition Genuine OEM Brand GE Location Freezer compartment Voltage 13.6V DC Amperage 0.23 A Fan Dimensions Approx. 4.5" x 4.5" Harness/Plug Length Approx. 8.25" from frame Repair Difficulty Easy — 15 to 30 minutes Quantity 1 fan motor Compatible Brands GE, Hotpoint, Haier, Monogram, Café, Profile, Kenmore Installation Notes ⚠️ Unplug Refrigerator Before Starting — Clear Any Frost Or Ice From The Fan Area Unplug the refrigerator and safely store any food that could spoil while the power is off. Wear work gloves. Locate the evaporator fan motor in the freezer compartment, typically behind an interior panel covering the evaporator coil assembly. If there's noticeable frost or ice buildup around the fan or coil, allow it to fully defrost before continuing — restricted airflow from ice is a common contributor to fan motor strain and noise. Remove the panel to access the fan motor, then disconnect the wiring harness from the old motor. Remove the mounting screws or clips securing the old motor and pull it free, along with the fan blade if it doesn't transfer separately. Install the new WR60X25858 in the same position, reconnect the wiring harness fully, and secure the mounting hardware. Reinstall the interior panel. While you're in this area, vacuuming out any accessible condenser coils is a good complementary maintenance step. Restore power and monitor the freezer's temperature over the next 24 hours to confirm normal, quiet operation and consistent cooling. Tools needed: Phillips screwdriver, work gloves. Frequently Asked Questions My freezer isn't cold anymore. Is this the part I need? Yes, this is one of the most common causes of a freezer that won't cool. One customer specifically reached out after their freezer wasn't cold, watched a diagnostic video explaining the evaporator fan's role, and confirmed this motor was the cause before ordering the replacement. I hear a strange noise from inside my freezer. Could this be the fan motor? Yes, this is a well-documented symptom. Noise often occurs when the fan motor itself is wearing out, or when frost or ice has built up enough to rub against the spinning fan blade. Clearing any ice buildup before replacing the motor helps you confirm whether the noise was from ice contact or the motor itself. Should I do anything else while I have the freezer open for this repair? It's a good opportunity to check for and clear any frost or ice buildup around the fan and coil area, since restricted airflow can contribute to fan strain. One customer also vacuumed out the condenser coils during the same repair, which is a reasonable companion maintenance step while everything is accessible. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by GE to factory specifications — guaranteed fit, materials, and performance. It matches the original motor design, voltage, and connection type of the evaporator fan motor originally installed in your refrigerator. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WR60X31997 Genuine OEM GE Refrigerator Ice Box Fan Motor The WR60X31997 is a genuine GE OEM ice box fan motor assembly for GE, Hotpoint, Haier, Monogram, and Café refrigerators. This motor is situated in the freezer section and circulates cold air specifically around the ice box area, playing a direct role in ice production as well as general cooling and airflow in that part of the freezer. Consistent airflow here is what keeps the ice maker producing normally and prevents warm spots from developing nearby. Rated 12V DC, 0.23A. Common causes of failure include a malfunctioning motor, worn-out bushings that hinder smooth rotation, or damaged fan blades that restrict airflow; mineral buildup can also gradually degrade the fan's efficiency over time. A failing ice box fan produces a recognizable set of symptoms: reduced or inadequate ice production, items in the freezer warming up or defrosting even with the door shut, unusual sounds or vibration when the fan runs, or uneven frost patterns suggesting the airflow in that area isn't circulating properly. It directly replaces PD00071430, 4964240, AP6978662, PS12744140, and EAP12744140. Quick Answer The WR60X31997 Genuine OEM GE Refrigerator Ice Box Fan Motor fixes GE, Hotpoint, Haier, Monogram, and Café refrigerators with reduced or inadequate ice production, freezer items warming up despite the door being shut, unusual fan noise or vibration, or uneven frost patterns. 12V DC, 0.23A. Replaces PD00071430, 4964240, AP6978662, PS12744140, EAP12744140. Common Problems This Part Fixes Reduced or inadequate ice production from the ice maker Items in the freezer warming up or partially defrosting even with the door shut Unusual sounds or vibrations coming from the ice box fan area Uneven frost patterns suggesting ineffective air circulation Fan blade that doesn't spin freely, or doesn't spin at all, when checked by hand Freezer running less efficiently overall near the ice box area Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This refrigerator ice box fan motor directly replaces the following OEM and cross-reference part numbers: WR60X31997, 4964240, AP6978662, EAP12744140, Nidec Model G11I12MS1AZ-57, PS12744140, AGE29835, PD00071430 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This ice box fan motor is compatible with select GE refrigerators, and also fits select Hotpoint, Haier, Monogram, Café, Profile, Fisher & Paykel, and Kenmore/Sears refrigerators built on the GE platform, including model numbers such as CQE28DM5NBS5, CVE28DM5NBS5, CVE28DM5NCS5, and CVE28DM5NS5. Note: This is the ice box fan motor specifically, a different component from GE's general evaporator fan motors used elsewhere in the freezer. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which fan motor your refrigerator needs. Key Features Genuine GE OEM part — factory-specified motor and blade design Circulates cold air around the ice box area, supporting ice production and nearby cooling Resolves "inadequate ice production," "items warming up," "unusual noise," and "uneven frost" symptoms caused by fan motor failure Premium motor coil and quality bearings for smooth, low-noise operation Rated 12V DC, 0.23A Direct drop-in replacement matching the original mounting and blade fitment Replaces PD00071430, 4964240, AP6978662, PS12744140, and EAP12744140 Compatible with GE, Hotpoint, Haier, Monogram, Café, Profile, Fisher & Paykel, and Kenmore/Sears refrigerators Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number WR60X31997 Part Type Refrigerator Ice Box Fan Motor Assembly Condition Genuine OEM Brand GE Location Freezer section, ice box area Function Circulates cold air to support ice production and cooling near the ice box Voltage 12V DC Amperage 0.23 A Quantity 1 fan motor assembly Compatible Brands GE, Hotpoint, Haier, Monogram, Café, Profile, Fisher & Paykel, Kenmore/Sears Installation Notes ⚠️ Unplug Refrigerator Before Starting Disconnect power at the outlet before beginning, and move perishable food to a cooler for the duration of the repair. Wear work gloves. Access the ice box fan by locating the panel or housing covering it in the freezer's ice box area — this may require removing the ice maker or nearby components for clearance depending on your model. Photograph the wiring and the fan blade's orientation before disconnecting anything. Disconnect the motor's wiring harness connector, remove the mounting screws or clips holding the motor bracket in place, and pull the motor and fan blade assembly free. Mount the new WR60X31997 in the same position, reconnect the wiring harness connector, and confirm the blade spins freely by hand without contacting the housing before reassembling any panels or components you removed for access. Restore power and monitor ice production and freezer temperature over the next 24 hours to confirm normal operation has returned. Tools needed: Phillips screwdriver, work gloves. Frequently Asked Questions My ice maker is producing less ice than usual. Could this fan be the cause? Yes, this is one of the more common symptoms of a failing ice box fan. Since this fan circulates cold air specifically around the ice box area, reduced airflow from a struggling or seized motor can directly slow down ice production, even if the rest of the freezer seems to be cooling normally. Items near the ice box seem to be warming up even though the freezer door is shut. Is that related? Yes. If this fan isn't circulating air properly, the area around the ice box can lose consistent cooling even while the rest of the freezer stays cold, since that zone depends specifically on this fan for airflow. This localized warming, paired with reduced ice production, is a strong combined signal pointing to this fan. Is this the same as a general evaporator fan motor? No, this is a distinct component. The ice box fan motor circulates air specifically around the ice box area to support ice production and nearby cooling, while a general evaporator fan motor circulates air across the evaporator coil for the freezer and fresh food compartments more broadly. The two serve different roles and are not interchangeable — always confirm which fan your model needs using your parts diagram or model number. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by GE to factory specifications — guaranteed fit, materials, and performance. It matches the original motor design, blade fitment, and mounting configuration of the ice box fan motor originally installed in your refrigerator. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 4681JB1027C Refrigerator Evaporator Fan Motor Replaces Part Numbers: 4681JB1027C, EAU60694512, 4681JB1027V, 4681JK1004E, AH3523323, EA3523323, EAU52096201, EAU60694529, SM1027C, AP4507961, PS3523323.  Replaces LG #4681JB1027C. 13VDC, 3.1 W, .24A. Has quick disconnect. Description: This Fan Motor is a replacement part for specific LG refrigerator models. It is essential for circulating air throughout the refrigerator and freezer compartments, ensuring that the temperature is evenly distributed and maintained at the set levels. This motor powers the fan that helps to cool the evaporator coils and dissipate heat, which is vital for the appliance's cooling efficiency. This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

5304532557 Refrigerator Genuine Evaporator Motor Replaces Part Numbers: 5304532557, 242077707, AP7194947, PS16745551. Description: This Part is a Genuine OEM refrigerator evaporator fan motor compatible with specific Electrolux, Frigidaire refrigerator models. The fan motor is a vital component of your refrigerator. It is designed to maintain cold temperatures by circulating air through the fresh food compartments. By doing so, it ensures uniform cooling within the refrigerator. This helps to prevent warm spots that can lead to frost build-up.

Read more less

4681JB1029D Refrigerator Genuine OEM Condenser Fan Motor Fits Specific LG, Kenmore Refrigerator Models Replaces Part Numbers: 4681JB1029D, EAU61644104, 1267566, AH3523330, EA3523330, OEM17751134, AP4437783, PS3523330. Description: This Condenser Fan Motor is a Genuine part for specific LG, Kenmore refrigerator models. This motor is responsible for powering the fan that cools the condenser coils, which helps dissipate heat from the refrigerator. Proper functioning of the condenser fan motor is crucial for maintaining the efficiency and cooling performance of the refrigerator. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

WP2315548 Refrigerator Genuine Evaporator Fan Motor  Replaces Part Numbers: WP2315548, 2315548, 1194733, 2220149, AP6007249, PS11740361. Description: The Evaporator Fan Motor is a Genuine OEM part for specific Whirlpool, Maytag refrigerator models. It is responsible for circulating cold air within the fridge and freezer compartments, helping to maintain even temperatures and keep food fresh. Causes of a bad evaporator fan motor include failure due to normal wear and tear over time, damage due to improper cleaning, or issues with the motor's electronic components.  

Read more less

XPARTCO W11224591 Refrigerator Evaporator Fan Motor The XPARTCO W11224591 is an aftermarket replacement freezer evaporator fan motor assembly compatible with a wide range of Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore bottom-mount French door refrigerators. The evaporator fan motor is located in the freezer compartment behind the rear panel — it draws cold air across the evaporator coils and circulates it throughout both the freezer and the fresh food compartment. This constant air movement is what keeps temperatures even and food fresh. When the fan motor fails, the most common symptom is telling: the refrigerator (fresh food) compartment stops cooling while the freezer stays cold but doesn't reach full capacity, because the fan is no longer moving the cold air up into the fridge section. This is a complete assembly that includes the fan motor, wiring harness, temperature sensor (thermistor), and defrost thermostat — everything integrated into one replaceable unit. Finished in white. As a direct replacement for the Whirlpool W11224591, it also replaces AP6329809, W10865431, W10728111, W11215582, 4844712, and PS12349521. Motor failure typically results from normal wear, obstruction from frost or debris rubbing the fan blade, or motor winding issues. Installs in 30–45 minutes with basic hand tools. Quick Answer The XPARTCO W11224591 Refrigerator Evaporator Fan Motor fixes Whirlpool, Maytag, KitchenAid, Jenn-Air, and Amana bottom-mount French door refrigerators where the fridge section is warm but the freezer is cold, temperatures are uneven, frost builds up on the coils, or unusual noise comes from the freezer compartment. Complete assembly — includes fan motor, wiring harness, temperature sensor, and defrost thermostat. White finish. Replaces AP6329809, W10865431, W10728111, W11215582, 4844712, PS12349521. Compatible with Whirlpool WRF757/WRF767/WRF736 series, KitchenAid KRFF507 series, Maytag MFT2574 series and related models. Common Problems This Part Fixes Refrigerator (fresh food) compartment warm while the freezer stays cold — the signature symptom of evaporator fan motor failure Uneven or inconsistent temperatures throughout the refrigerator Unusual noises from the freezer compartment — grinding, squealing, or clicking as the motor bearings fail or the blade rubs on frost/ice Frost or ice buildup around the cooling sections and evaporator coils Refrigerator running continuously or more frequently than usual to compensate for poor air circulation Noticeable decrease in overall cooling efficiency Food spoiling faster than normal in the fresh food compartment Fan motor not spinning at all when the compressor is running Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This evaporator fan motor assembly directly replaces the following OEM and cross-reference part numbers: W11224591, W10865431, 4844712, W10728111, W11215582, AP6329809, AWP43665, EAP11738038, FIX12349521, DLB5985WPEB, PD00052715, PS12349521. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This evaporator fan motor is compatible with select bottom-mount French door refrigerators from the following brands: Whirlpool refrigerators — WRF757SDHV00, WRF757SDHZ00/Z01/Z02, WRF767SDHV00/V02, WRF767SDHZ00/Z01/Z02 series Whirlpool refrigerators — WRF736SDAB14, WRF736SDAM14, WRF736SDAW14, 7WF736SDAM14 series KitchenAid refrigerators — KRFF507HPS00/PS01/PS02, KRFF507HBS02, KRFF507HWH02 series Maytag refrigerators — MFT2574DEH02 and related bottom-mount French door models Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper refrigerators — select Whirlpool-built models Kenmore / Sears and Ikea refrigerators — select Whirlpool-built models Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Complete evaporator fan motor assembly — includes fan motor, wiring harness, temperature sensor (thermistor), and defrost thermostat in one integrated unit Circulates cold air from the evaporator coils throughout the freezer and fresh food compartments for even temperatures Resolves the classic "fridge warm, freezer cold" symptom of evaporator fan failure Prevents frost buildup by maintaining proper airflow across the coils White finish, direct-fit replacement using original mounting points and connectors Because the assembly bundles the defrost thermostat and temperature sensor, it addresses multiple potential failure points in a single repair Replaces AP6329809, W10865431, W10728111, W11215582, 4844712, and PS12349521 Compatible with Whirlpool WRF757/WRF767/WRF736 series, KitchenAid KRFF507 series, Maytag MFT2574 series, plus Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore, and Ikea Whirlpool-built bottom-mount refrigerators Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 30–45 minutes with basic hand tools Product Specifications Part Number W11224591 Part Type Freezer Evaporator Fan Motor Assembly Condition Aftermarket Replacement Application Bottom-Mount French Door Refrigerators (Whirlpool platform) Assembly Includes Fan Motor, Wiring Harness, Temperature Sensor (Thermistor), Defrost Thermostat Location Freezer compartment, behind rear panel Color White Compatible Brands Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore, Ikea Installation Notes ⚠️ Unplug Refrigerator and Move Perishable Food Before Starting — Wear Work Gloves Unplug the refrigerator and safely store any food that could spoil while the power is off. Wear work gloves to protect your hands. The evaporator fan motor is located in the freezer compartment behind the rear access panel. Remove all freezer shelves, drawers, and the ice maker (if equipped) to clear access to the back wall. If there's frost or ice buildup on the rear panel or coils, allow the freezer to thaw completely before continuing — never chip or pry ice off the evaporator coils, as the aluminum fins damage easily. Remove the screws securing the rear freezer access panel and lift it away to expose the evaporator coils and fan motor assembly. Photograph the wiring harness connections and the fan motor orientation before disconnecting anything. Disconnect the wire harness connectors from the old assembly and release it from its mounting points. Lift out the old fan motor assembly. Install the new W11224591 assembly using the original mounting points and connectors — since this is a complete assembly, the fan motor, harness, temperature sensor, and defrost thermostat all transfer as one unit. Reconnect the wiring harness, matching your photos. Confirm the fan blade spins freely by hand without rubbing on any surrounding surface. Reinstall the rear access panel, shelves, drawers, and ice maker. Plug the refrigerator back in and allow several hours for the unit to return to its set temperature before reloading with food. Test airflow and temperature consistency before considering the job complete. Tools needed: Phillips screwdriver, 1/4" nut driver, work gloves. Frequently Asked Questions My refrigerator section is warm but the freezer is still cold — is this the fan motor? This is the single most common and telling symptom of a failed evaporator fan motor on these bottom-mount French door refrigerators. Here's why: the evaporator coils (which produce the cold) are in the freezer, and the evaporator fan is what pushes that cold air up into the fresh food compartment. When the fan motor fails, the freezer stays cold (it's right next to the coils) but the fridge section warms up because no air is being circulated to it. If your freezer is cold and your fridge is warm, the evaporator fan motor is the prime suspect. You can confirm by listening for the fan running when the compressor is on, or opening the freezer rear panel to see if the fan spins. What's included with this part — is it just the motor? This is a complete assembly, not just the bare motor. It includes the fan motor, the wiring harness, the temperature sensor (thermistor), and the defrost thermostat — all integrated into one unit. This is actually an advantage: since these components live together in the freezer compartment and can each cause cooling problems, replacing them as a bundle addresses multiple potential failure points in a single repair, reducing the chance you'll be back in the freezer compartment a few months later for a related part. Why is my evaporator fan making noise? A noisy evaporator fan usually means one of two things: the motor bearings are wearing out (producing grinding or squealing), or the fan blade is rubbing against frost or ice that has built up around it. If frost buildup is the cause, that often points to a secondary problem with the defrost system (defrost heater, thermostat, or control) allowing ice to accumulate where it shouldn't. Since this replacement assembly includes a new defrost thermostat, it addresses one of the common defrost-related causes. If heavy frost keeps returning after replacement, the defrost heater or control board should be investigated next. Do I need to defrost the freezer before installing this? If there's frost or ice buildup on the rear freezer panel or evaporator coils, yes — clear it before installing the new assembly. Leave the freezer empty and unplugged with the door open for several hours (longer for heavy ice) to let everything thaw naturally, placing towels at the base to catch melt water. Never chip or pry ice off the evaporator coils with a tool — the aluminum fins are delicate and a damaged coil is a far more expensive repair. Once everything is fully thawed and dried, proceed with the fan motor replacement. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the fit, mounting points, connector configuration, and function of the original W11224591 evaporator fan motor assembly used in compatible Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, and Kenmore bottom-mount French door refrigerators — including the integrated harness, temperature sensor, and defrost thermostat. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

Genuine OEM WR60X46085 Refrigerator Condenser Motor Fan Blade The WR60X46085 is a genuine OEM condenser Motor fan blade assembly for GE, Hotpoint, and RCA refrigerators. The blade presses onto the condenser fan motor shaft and pulls air across the condenser coil and compressor, carrying heat away so the sealed system can cool properly. When a blade cracks, loses a vane, or works loose on the shaft, the fan becomes noisy or unbalanced, or stops moving air, and the compressor and condenser start running hot. This is a genuine OEM part from GE Appliances, not an aftermarket equivalent, so the blade matches the original factory fit and balance. Note that this is the blade only. The condenser fan motor is a separate part, so if the motor itself has failed, the blade alone will not fix the problem. Quick Answer The Genuine OEM WR60X46085 Condenser Motor Fan Blade fixes a GE, Hotpoint, or RCA refrigerator with a noisy, rattling, or vibrating condenser fan, or a fan that spins without moving air because the blade is cracked, damaged, or loose. Genuine OEM, replaces the earlier WR60X10207 and WR60X10088 blades. Classic symptom: rattling or buzzing from the bottom rear of the refrigerator, or a warm cabinet with a compressor that runs constantly. Common Problems This Part Fixes Rattling, buzzing, or vibrating noise from the condenser fan area Visibly cracked, chipped, or broken blade vanes Blade loose on the motor shaft or spinning without moving air Compressor running constantly or running hot from poor condenser airflow Refrigerator not cooling well because heat isn't being removed from the condenser coil Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This condenser fan blade replaces the following part numbers: WR60X46085, WR60X10207, WR60X10088, AGE1580527, AP8075891, EAP1022410, PD00097217, PS1022410 GE has superseded WR60X10088 with WR60X10207, and WR60X10207 with the current WR60X46085. If your parts diagram or old blade shows either earlier number, the WR60X46085 is the current genuine replacement. Compatibility This blade is listed for refrigerators from the following brands: GE refrigerators Hotpoint refrigerators RCA refrigerators Note: A full model list isn't shown here, so confirm fit by matching the number on your old blade or your refrigerator's parts diagram against the Replaces list above, or contact our support team with your model number and we'll verify before you order. This is the blade only. The condenser fan motor is sold separately. Key Features Genuine OEM GE condenser Motor fan blade assembly, not an aftermarket equivalent Current part number, superseding WR60X10207 and WR60X10088 Restores quiet, balanced airflow across the condenser coil Authorized by GE for refrigerator models using flammable refrigerant such as R600a Blade only. Motor not included Simple replacement, typically 15–30 minutes Product Specifications Part Number WR60X46085 OEM Part Number WR60X46085 Part Type Refrigerator Condenser Motor Fan Blade Condition Genuine OEM Manufacturer GE Appliances Supersedes WR60X10207, WR60X10088 Included Condenser Fan Blade Only Application GE, Hotpoint & RCA Refrigerators Installation Notes ⚠️ Unplug Power Before Installing Unplug the refrigerator before starting. Pull the unit out and remove the rear or lower access panel to reach the condenser fan, which sits near the compressor. Pull the old blade off the motor shaft, noting how far it sits on the shaft and which way it faces. Press the new blade on to the same position, making sure it spins freely without touching the shroud or motor. While the panel is off, vacuum dust from the condenser coil and fan area, since buildup is a common cause of overheating. Replace the panel, push the refrigerator back, and restore power. Frequently Asked Questions My refrigerator is making a rattling noise at the back — is this the part I need? It could be. A cracked, chipped, or loose condenser fan blade is a common source of rattling or vibration near the compressor. Inspect the blade for damage and check that it spins freely. If the blade looks fine but the fan won't turn, the condenser fan motor may be the problem instead. Does this include the motor? No. This is the fan blade only. The condenser fan motor is a separate part. My old blade is a WR60X10207 or WR60X10088. Will this work? Yes. WR60X46085 is the current GE part number that supersedes both earlier numbers. Is this a genuine GE part? Yes. This is a genuine OEM part from GE Appliances, not an aftermarket equivalent. Will this fit my refrigerator? It is listed for GE, Hotpoint, and RCA refrigerators. Match the number on your old blade or parts diagram against the Replaces list, or contact our support team with your model number and we'll confirm fit before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

WP2315539 Genuine OEM Whirlpool Refrigerator Evaporator Fan Motor The WP2315539 is a genuine Whirlpool OEM evaporator fan motor for Whirlpool side-by-side refrigerators. This motor draws air across the evaporator coil, cooling it, and circulates that cold air from the freezer into the fresh food compartment, keeping both sides of the refrigerator at consistent, even temperatures and preventing warm spots that can lead to food spoilage. This part features an incorporated wire harness. Over time, the motor's bearings wear out or the motor fails electrically, and when this happens it commonly generates noticeable noise from the freezer area before it fails completely. Symptoms include unusual noise from the freezer, the fresh food compartment running warm while the freezer stays cold, ice buildup on the evaporator coil, or inconsistent cooling overall. It directly replaces 2219689, 2225625, 2315539, W10438708, and WP2315539VP. Quick Answer The WP2315539 Genuine OEM Whirlpool Refrigerator Evaporator Fan Motor fixes Whirlpool side-by-side refrigerators with unusual noise from the freezer, a fresh food compartment running warm while the freezer stays cold, ice buildup on the evaporator coil, or inconsistent cooling. Includes incorporated wire harness. Replaces 2219689, 2225625, 2315539, W10438708, WP2315539VP. Not the same as the similarly-numbered 2315549 motor — confirm you have the exact part number before ordering. Common Problems This Part Fixes Unusual or increasing noise coming from the freezer area Fresh food compartment running warm while the freezer stays cold Ice buildup on the evaporator coil Inconsistent or fluctuating cooling throughout the refrigerator Refrigerator running constantly as it struggles to maintain temperature Fan blade that doesn't spin freely, or doesn't spin at all, when checked by hand Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This refrigerator evaporator fan motor directly replaces the following OEM and cross-reference part numbers: WP2315539, 2315539, W10438708, 1372146, 2219689, 2225625, ESF-U2B, AP6007247, AWP47336, EAP11740359, PD00003243, PS11740359 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This evaporator fan motor is compatible with select Whirlpool side-by-side refrigerators. Always verify your full model number before ordering, as this part is designed for the side-by-side (SxS) platform specifically. Note — not the same as 2315549: This motor is a separate part from the similarly-numbered 2315549 evaporator fan motor, which is used on different Whirlpool refrigerator models. The two numbers are easy to mix up given how close they are — always confirm the exact part number from your appliance or parts diagram before ordering. This motor also includes an incorporated wire harness; if your original motor does not have one, a different, related part number may be needed instead. Contact our support team with your model number if you're unsure which motor your refrigerator needs. Key Features Genuine Whirlpool OEM part — factory-specified motor design and airflow performance Circulates cold air from the freezer into the fresh food compartment on side-by-side models Resolves "noisy freezer," "fresh food running warm," "ice buildup," and "inconsistent cooling" symptoms Incorporated wire harness for a direct plug-in fit Factory Certified Part built to Whirlpool's engineering specifications Direct drop-in replacement matching the original mounting and blade fitment Replaces 2219689, 2225625, 2315539, W10438708, and WP2315539VP Compatible with Whirlpool side-by-side refrigerators Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number WP2315539 Part Type Refrigerator Evaporator Fan Motor (SxS) Condition Genuine OEM Brand Whirlpool Application Side-by-Side Refrigerators Function Circulates cold air from the freezer to the fresh food compartment Wire Harness Incorporated Repair Difficulty Medium Quantity 1 fan motor Compatible Brand Whirlpool Installation Notes ⚠️ Unplug Refrigerator Before Starting Before beginning any repair work, always turn off power to the appliance and unplug it from the wall outlet, storing any perishable food safely while power is off. Wear work gloves. Remove the rear access panel from the refrigerator by unscrewing the screws attaching it to the back of the unit. Locate the evaporator fan motor within the refrigerator as indicated in your model's manual. If there's significant frost or ice around the fan or coil, let the unit sit unplugged with the door open for a few hours before continuing. Unplug the wiring harness from the old fan motor, remove the screws securing it in place, and remove the old motor. Install the new WP2315539 in the same position, reconnect the wiring harness, and secure the new motor with the mounting screws. Replace the rear access panel and restore power, then check to confirm the fan motor is working properly and both compartments are cooling evenly. Tools needed: Phillips screwdriver, flathead screwdriver, work gloves. Frequently Asked Questions My freezer is getting noisy. Is this the evaporator fan motor? It's a strong possibility. When this motor's bearings begin to wear, it commonly generates noticeable noise in the freezer area well before it fails outright. If you're hearing new or increasing noise from the freezer, this motor is a reasonable first thing to check. Does this motor include the wire harness, or do I need to buy that separately? This motor comes with an incorporated wire harness already attached, so no separate harness purchase is needed for a standard installation. If your original motor's connector setup looks different from what's included here, double-check compatibility with our support team before ordering. Is this the same as the 2315549 motor I've seen listed elsewhere? No, these are two separate part numbers that are easy to confuse given how similar they look. Always confirm the exact part number from your refrigerator's parts diagram or the sticker on your old motor rather than assuming based on a close number match. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original motor design, wire harness, and blade fitment of the evaporator fan motor originally installed in your refrigerator. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

5040JA2009B Genuine OEM LG Refrigerator Motor Damper Grommet (Front) The 5040JA2009B is a genuine LG OEM front evaporator motor grommet for LG and select Kenmore refrigerators, and also fits select freezers. This rubber grommet cushions and secures the front side of the evaporator fan motor's mount, reducing vibration and noise as the motor runs. It's the front-position counterpart to our 5040JA2004A rear grommet — LG mounts this evaporator fan motor from both the front and rear with matching grommets working together. Made of rubber, this grommet naturally degrades from prolonged use, exposure to the freezer's cold temperatures, or physical damage from an accidental impact during cleaning or organizing. Once it fails, the evaporator motor loses proper cushioning and can shift slightly out of alignment. Symptoms of a bad grommet include increased noise and vibration, particularly noticeable when the evaporator fan motor is running, along with a rattling or buzzing sound coming from the freezer area. It directly replaces AP4443769, 1268013, AH3526237, EA3526237, PS3526237, and 5040JQ2003B. Quick Answer The 5040JA2009B Genuine OEM LG Refrigerator Motor Damper Grommet (Front) fixes LG and select Kenmore refrigerators with increased noise or vibration from the evaporator fan motor, or a rattling/buzzing sound from the freezer area. Rubber, front-position grommet for the evaporator fan motor. Replaces AP4443769, 1268013, AH3526237, EA3526237, PS3526237, 5040JQ2003B. This is the front counterpart to our 5040JA2004A rear grommet — both support the same evaporator fan motor from opposite sides. Common Problems This Part Fixes Increased noise or vibration from the evaporator fan motor Rattling or buzzing sound coming from the freezer area Noise that's especially noticeable when the fan motor is running Evaporator motor that has shifted slightly out of alignment Visibly cracked, hardened, or damaged rubber grommet Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This motor damper grommet directly replaces the following OEM and cross-reference part numbers: 5040JA2009B, AP4443769, 1268013, AH3526237, EA3526237, PS3526237, 5040JQ2003B If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This front evaporator motor grommet is compatible with select LG refrigerators and freezers, and also fits select Kenmore refrigerators built on the LG platform, including model numbers such as LFXC24726S, LMXS30776S, LSC27950ST, LFC20760SB, LFX25960SB, and LFX28968ST/02. Note — front grommet, not rear: This is the front-position evaporator motor grommet. The matching rear-position grommet for the same motor is a separate part, our 5040JA2004A listing. Both are typically checked and often replaced together, since they support the same motor and are usually the same age. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine LG OEM part — factory-specified rubber compound and fit Cushions and secures the front side of the evaporator fan motor mount Resolves "increased motor noise," "vibration," and "rattling/buzzing from the freezer" symptoms Front-position counterpart to our 5040JA2004A rear grommet Durable rubber construction designed for the freezer's cold operating environment Direct drop-in replacement — no tools required for the grommet itself Replaces AP4443769, 1268013, AH3526237, EA3526237, PS3526237, and 5040JQ2003B Compatible with LG and select Kenmore refrigerators and freezers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number 5040JA2009B Part Type Front Evaporator Motor Grommet Condition Genuine OEM Brand LG Material Rubber Function Cushions and secures the front side of the evaporator fan motor mount Position Front Related Part 5040JA2004A (rear-position grommet for the same motor, sold separately) Repair Difficulty Moderate — freezer teardown required for access Quantity 1 damper grommet Compatible Brands LG, Kenmore Installation Notes ⚠️ Unplug Refrigerator Before Starting — Photograph Wiring Before Disconnecting Disconnect power at the outlet before beginning, and move perishable food to a cooler for the duration of the repair. Wear work gloves. Access to the evaporator motor on many models requires going in through the freezer: empty the top half of the freezer, remove the side rails holding the ice bin, then remove the outer screws holding the ice auger assembly — on many models this means only the two outer screws on each side, not the middle ones. With the ice maker components clear, remove the rear panel to access the evaporator fan motor and its front and rear grommets. Photograph the wiring connections carefully before disconnecting anything, since several wires can look interchangeable but are not, and reconnecting one in reverse can cause a malfunction. Remove the old front grommet from the motor mount — it typically pulls free without tools. Press the new 5040JA2009B grommet into the same position, seating it fully. If the rear grommet is also worn, this is a good time to replace it as well since you already have access. Reassemble the ice maker components, rear panel, and any other parts removed for access, restore power, and run the refrigerator for a while to confirm the noise or vibration has resolved. Tools needed: Phillips screwdriver, work gloves. Frequently Asked Questions Should I replace the rear grommet at the same time as this front one? It's worth considering. Both grommets support the same evaporator fan motor from opposite sides and are typically the same age, so if one has degraded, the other is often not far behind. Since accessing the motor for this repair already requires a fair amount of teardown, replacing both together — our 5040JA2004A rear grommet and this front one — saves you from repeating the same access work again soon after. Why do I need to go through the ice maker to reach this part? On many LG refrigerator models, the evaporator fan motor and its grommets sit behind the freezer's ice maker assembly, so reaching them requires removing the ice bin, its side rails, and the auger mechanism first. This is a more involved access path than some other freezer repairs, so budget extra time and take photos as you go to keep track of how everything reassembles. Why is it so important to photograph the wiring before disconnecting? Several of the wires in this area can look similar and are easy to connect in reverse or in the wrong position, which can cause a malfunction after reassembly. Taking clear photos of each connection before you disconnect anything is a simple step that prevents a frustrating troubleshooting session later. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by LG to factory specifications — guaranteed fit, materials, and performance. It matches the original rubber compound and mounting fit of the front evaporator motor grommet originally installed in your refrigerator. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

5040JA2004A Genuine OEM LG Refrigerator Motor Damper Grommet (Rear) The 5040JA2004A is a genuine LG OEM rubber motor damper grommet for LG and select Kenmore refrigerators. This small rubber component mounts and isolates a fan motor from the surrounding bracket, cushioning it against vibration as the motor runs. This is the rear-position grommet; LG refrigerators typically use more than one grommet to support a fan motor from multiple points. Made of rubber, this grommet naturally degrades over years of exposure to cold temperatures and constant vibration, eventually cracking, hardening, or losing its cushioning shape. Once it fails, the motor it supports is no longer properly isolated, and the metal motor bracket can end up in direct contact with the surrounding housing. A worn or failed grommet typically shows up as new or worsening rattling, buzzing, or vibration noise coming from the back of the refrigerator, especially noticeable when the fan motor is running. It directly replaces 5040JA2004B, 1268010, AP4635690, AH3526229, EA3526229, PS3526229, EAP3526229, and PD00027884. Quick Answer The 5040JA2004A Genuine OEM LG Refrigerator Motor Damper Grommet (Rear) fixes LG and select Kenmore refrigerators with new or worsening rattling, buzzing, or vibration noise from the back of the unit, especially when the fan motor is running. Rubber, rear-position grommet. Replaces 5040JA2004B, 1268010, AP4635690, AH3526229, EA3526229, PS3526229, EAP3526229, PD00027884. This grommet is used with a fan motor at the rear of the refrigerator; sources vary on whether that's the evaporator or condenser fan depending on the specific model, so confirm your model number before ordering. Common Problems This Part Fixes Rattling or buzzing noise from the back of the refrigerator Vibration noise that's especially noticeable when the fan motor is running Noise that has gradually worsened over time Visibly cracked, hardened, or flattened rubber grommet Motor bracket that feels loose or vibrates excessively against its housing Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This motor damper grommet directly replaces the following OEM and cross-reference part numbers: 5040JA2004A, 1268010, AP4635690, AH3526229, EA3526229, PS3526229, EAP3526229, PD00027884 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This motor damper grommet is compatible with select LG refrigerators, and also fits select Kenmore refrigerators built on the LG platform, including model numbers such as LSXS26386S00, LTCS20030S/00, LTC24380SB00, LRSCS21935SW, LFC24770ST/02, LSXS26326W/01, and Kenmore 795.79043311, 795.51089011, 795.51832412, 795.79412810, and 795.78032211. Note: This is the rear-position grommet. LG also lists a related grommet, part number 5040JA2009B, used as a support damper for fan motors on other models — the two are not necessarily interchangeable, so confirm your exact part number and position before ordering. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine LG OEM part — factory-specified rubber compound and fit Isolates the fan motor from its bracket, cushioning it against vibration Resolves "rattling," "buzzing," and "vibration noise" symptoms caused by a worn or failed grommet Rear-position grommet Durable rubber construction designed for the refrigerator's cold operating environment Direct drop-in replacement — no tools required on most models Replaces 5040JA2004B, 1268010, AP4635690, AH3526229, EA3526229, PS3526229, EAP3526229, and PD00027884 Compatible with LG and select Kenmore refrigerators Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number 5040JA2004A Part Type Fan Motor Damper Grommet — Rear Condition Genuine OEM Brand LG Material Rubber Function Isolates and cushions a fan motor from vibration at its bracket Position Rear Related Part 5040JA2009B (support damper, different position/models — verify before substituting) Repair Difficulty Very Easy — typically no tools required Quantity 1 damper grommet Compatible Brands LG, Kenmore Installation Notes ⚠️ Unplug Refrigerator Before Starting Disconnect power at the outlet before beginning, and move perishable food to a cooler if access requires opening the freezer compartment. Wear work gloves. Access depends on your model — this grommet supports a fan motor that may be located behind the freezer's rear interior panel or in the compressor/machine compartment at the back or bottom of the unit, so check your model's service diagram for the exact location. Remove any panel screws needed to reach the motor bracket. Photograph the grommet's position and how it seats against the bracket before removing it. Gently remove the old, worn grommet from around the motor mounting post — it typically pulls or presses off without tools. Press the new 5040JA2004A grommet into the same position, seating it fully so it cushions the motor bracket evenly. Reassemble any panels removed for access, restore power, and run the refrigerator for a while to confirm the rattling or vibration noise has resolved. Tools needed: Phillips screwdriver (for panel access), work gloves. Frequently Asked Questions My refrigerator has developed a rattling noise from the back. Is this the grommet? Yes, this is a common cause of exactly that symptom. Once the rubber grommet cracks, hardens, or loses its cushioning shape, the fan motor's mounting bracket is no longer properly isolated and can vibrate directly against the surrounding housing, producing a rattling or buzzing noise — especially noticeable whenever the fan motor is actively running. Is this for the evaporator fan motor or the condenser fan motor? Sources describe this grommet's application somewhat differently depending on the specific refrigerator model — some reference it as supporting the evaporator fan motor, others the condenser fan motor. In practice, this reflects that LG uses the same grommet design for fan motor mounting in more than one location depending on the model. Confirm your full model number against the compatibility list, or check your appliance's parts diagram, to be certain which motor this grommet supports on your specific unit. Do I need any tools to replace this? The grommet itself is tool-free — it simply presses into place around the motor mounting post. You will likely need a screwdriver to remove whatever panel is covering the area where the motor and grommet are located, but the grommet swap itself requires no tools. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by LG to factory specifications — guaranteed fit, materials, and performance. It matches the original rubber compound and mounting fit of the motor damper grommet originally installed in your refrigerator. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

5901JA1021A Genuine OEM LG Refrigerator Evaporator Fan Blade The 5901JA1021A is a genuine LG OEM evaporator fan blade for LG and select Kenmore refrigerators. This is the plastic blade itself — not the motor — that mounts onto the evaporator fan motor's shaft and physically moves air through the evaporator fins and interior compartment as it spins, which is what carries cooled air to the fresh food and freezer sections and helps maintain efficient, even cooling. Over time, the blade can crack, chip, or warp from ice contact, age, or physical damage, even while the motor underneath it is still working perfectly fine. A damaged fan blade typically shows up as reduced airflow and less effective cooling, a wobbling or unbalanced sound as the fan spins, or visible cracks and missing pieces on the blade itself. Since this is the blade only, it's a straightforward and inexpensive fix when the motor is still good but the blade has failed. It directly replaces 5901JJ1005A, AP4457221, 1268187, AH3528674, EA3528674, and PS3528674. Quick Answer The 5901JA1021A Genuine OEM LG Refrigerator Evaporator Fan Blade fixes LG and select Kenmore refrigerators with reduced cooling airflow, a wobbling or unbalanced fan noise, or a cracked/chipped/missing fan blade. Replaces 5901JJ1005A, AP4457221, 1268187, AH3528674, EA3528674, PS3528674. This is the blade only, not the motor — if your fan motor itself has failed (won't spin, no power, electrical fault), you need a motor replacement instead, such as our EAU61524007 listing. Common Problems This Part Fixes Reduced airflow and less effective cooling despite the fan motor running Wobbling, unbalanced, or rattling sound as the fan spins Visible cracks, chips, or missing sections on the fan blade Fan blade that has broken away from the motor shaft Inconsistent cooling performance in the refrigerator or freezer Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This refrigerator evaporator fan blade directly replaces the following OEM and cross-reference part numbers: 5901JA1021A, 5901JJ1005A, 1268187, ADP73694301, ALG51767, AP4457221, EAP3528674, PD00009011 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This evaporator fan blade is compatible with select LG refrigerators, and also fits select Kenmore refrigerators built on the LG platform, including model numbers such as 71052, 71053, 71059, 71073, 71602, 71603, and 71609. Note — blade only, not the motor: This listing is for the fan blade component only. If your evaporator fan motor itself has failed electrically (won't spin at all, no power, humming with no rotation), you need a full motor replacement instead of just this blade. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which part your refrigerator needs. Key Features Genuine LG OEM part — factory-specified blade design and shaft fit Mounts directly onto the existing evaporator fan motor shaft Resolves "reduced airflow," "wobbling fan noise," and "cracked or chipped blade" symptoms Inexpensive fix when only the blade — not the motor — has failed Durable plastic construction designed for the freezer environment Direct drop-in replacement — no tools required on most models Replaces 5901JJ1005A, AP4457221, 1268187, AH3528674, EA3528674, and PS3528674 Compatible with LG and select Kenmore refrigerators Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number 5901JA1021A Part Type Refrigerator Evaporator Fan Blade (Blade Only) Condition Genuine OEM Brand LG Material Plastic Function Moves air through the evaporator fins and compartment when mounted to the fan motor shaft Includes Motor No — blade only Repair Difficulty Very Easy — typically no tools required Quantity 1 fan blade Compatible Brands LG, Kenmore Installation Notes ⚠️ Unplug Refrigerator Before Starting Disconnect power at the outlet before beginning, and move perishable food to a cooler for the duration of the repair. Wear work gloves. Access is typically through the freezer's rear interior panel: remove shelving and bins as needed, then remove the screws securing the back panel to expose the evaporator fan. If there's significant frost or ice around the fan or coil, let the unit sit unplugged with the door open for a few hours, or run a manual defrost, before continuing. Photograph the old blade's orientation on the motor shaft before removing it. Gently pull the old fan blade off the motor shaft — it typically presses on and off without tools. Press the new 5901JA1021A blade onto the same motor shaft in the same orientation, seating it fully. Confirm the blade spins freely by hand without wobbling or contacting the housing before reassembling the back panel. Restore power and monitor cooling performance over the next 24 hours to confirm normal, even airflow has returned. Tools needed: Phillips screwdriver (for the rear panel), work gloves. Frequently Asked Questions How do I know if I need just the blade or the whole motor? Check whether the motor is actually turning. If you can see or hear the motor shaft spinning but the blade is cracked, wobbling, or missing pieces, this blade-only replacement is the correct and less expensive fix. If the motor itself isn't turning at all — no spin, no hum, or an electrical fault — the motor has failed and needs to be replaced instead, which is a different part from this blade. My fan makes a wobbling or rattling noise. Is that the blade? It's a strong possibility, especially if the motor itself sounds otherwise normal. A cracked, chipped, or unevenly worn blade can throw off the fan's balance as it spins, producing a rattling or wobbling sound distinct from the grinding noise typically associated with a failing motor bearing. Do I need any tools to replace this blade? No, in most cases. The blade presses onto and off of the motor shaft without tools — you'll just need a screwdriver to access the rear panel covering the evaporator fan area, but the blade swap itself is tool-free. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by LG to factory specifications — guaranteed fit, materials, and performance. It matches the original blade design and motor shaft fit of the evaporator fan blade originally installed in your refrigerator. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less