Appliance Parts

XPARTCO DA47-00243K Refrigerator Defrost Thermostat The XPARTCO DA47-00243K is an aftermarket replacement defrost bi-metal thermostat compatible with select Samsung French door and bottom freezer refrigerators. This thermostat is a critical component in the automatic defrost system, functioning as a thermal safety device that monitors the temperature of the evaporator coils during the defrost cycle. When the evaporator reaches the preset maximum temperature of 140°F (60°C), the bi-metal thermostat opens the circuit and cuts power to the defrost heater — preventing overheating and damage to the evaporator. It resets and closes again at 104°F (40°C), allowing the next defrost cycle to begin normally. When the thermostat fails, it can cause excessive frost buildup on the evaporator coils, poor cooling performance, or a heater that won't shut off — all resulting in the refrigerator failing to maintain proper temperatures. Quick Answer The XPARTCO DA47-00243K Refrigerator Defrost Thermostat fixes refrigerators with excessive frost buildup, a freezer that is too cold while the fridge is too warm, a heater that won't shut off, or a refrigerator that stops cooling. It is compatible with select Samsung French door and bottom freezer refrigerators and opens at 140°F to protect the evaporator from overheating. Common Problems This Part Fixes Excessive frost or ice buildup on evaporator coils Freezer too cold while refrigerator section is too warm Defrost heater not shutting off after defrost cycle Refrigerator not cooling or maintaining temperature Food spoiling faster than normal Unusual humming or running sounds from the back of the fridge Replaces Part Numbers This thermostat directly replaces the following OEM and cross-reference part numbers: DA47-00243K, 2025696, DA47-00243B, DA47-00243C, DA47-00243J, ASM30257, PD00002154, EAP4140510, AP4403832, PS4140510. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This defrost thermostat is compatible with select refrigerators from the following brands: Samsung French door refrigerators Samsung bottom freezer refrigerators Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Bi-metal thermal safety device — opens at 140°F (60°C) to cut power to the defrost heater and prevent evaporator overheating Resets automatically at 104°F (40°C) — allowing the next defrost cycle to begin normally Aftermarket replacement built to OEM-equivalent quality standards 2-terminal design — direct drop-in replacement, no modification required Restores proper frost-free operation and refrigerator cooling performance DIY-friendly repair — installs with basic hand tools in 30–45 minutes Budget-friendly alternative to OEM at a lower cost without sacrificing performance Product Specifications Part Number DA47-00243K Part Type Defrost Bi-Metal Thermostat Condition Aftermarket Replacement Application Refrigerator Defrost System Open Temperature 140°F (60°C) Close Temperature 104°F (40°C) Terminals 2 Compatible Brands Samsung Installation Notes ⚠️ Safety First — Unplug Refrigerator Before Starting Unplug the refrigerator from the power source before beginning any repair. Safely remove and store any food that could deteriorate while the power is off. Wear work gloves to protect your hands. Access the evaporator coils by removing the rear panel inside the freezer compartment. Disconnect the wiring harness from the old thermostat and clip the new DA47-00243K thermostat onto the evaporator coil in the same position. Reconnect the wiring harness and reassemble the freezer panel. Allow 24 hours for the refrigerator to return to normal operating temperature. Consult your refrigerator's service manual for model-specific instructions. Frequently Asked Questions Will the DA47-00243K fit my Samsung refrigerator? This thermostat is compatible with select Samsung French door and bottom freezer refrigerators. Use the model search above to verify your model, or contact our support team before ordering. What does a defrost thermostat do? The defrost bi-metal thermostat monitors the temperature of the evaporator coils during the defrost cycle. It opens the circuit and cuts power to the defrost heater when the evaporator reaches 140°F (60°C), preventing overheating. It automatically resets and closes again at 104°F (40°C) to allow the next cycle. What are signs that my defrost thermostat needs replacement? Common signs include: excessive frost or ice buildup on the evaporator coils, the freezer running too cold while the refrigerator section is too warm, the defrost heater failing to shut off, or the refrigerator not maintaining proper temperatures and food spoiling faster than normal. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is designed to deliver reliable, long-lasting performance at a more affordable price point. At what temperatures does the DA47-00243K open and close? The thermostat opens (cuts power to the heater) at 140°F (60°C) and closes (resets) at 104°F (40°C). Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 691366 Dryer Idler Pulley Assembly Replaces WP691366 The XPARTCO 691366 is an aftermarket replacement dryer idler pulley assembly compatible with a wide range of Whirlpool-family dryers — particularly models with the lint filter on top — including Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Crosley, Estate, Inglis, Admiral, Magic Chef, and Norge. The idler pulley assembly is a spring-tensioned arm and wheel that presses against the drum drive belt to maintain correct belt tension as it wraps around the drum and motor pulley. Without proper tension, the belt slips off the motor pulley, causing the drum to stop spinning. A worn idler pulley bearing also causes squealing, squeaking, or thumping noises during operation. This is a complete idler arm and pulley assembly — it includes both the spring arm and the wheel, and mounts directly to the existing bracket in the dryer. Overall dimensions are 6"L x 1-5/8"W x 3-7/8"H with a 1-7/8" diameter pulley wheel. It replaces older Teflon friction-style idler pulleys and provides a smoother, longer-lasting ball-bearing wheel. It directly replaces WP691366, 691366, 239477, 337116, 337407, 3394332, 347034, 347226, 4319391, 688166, W10612905, AP6010582, PS11743765, and over 20 additional cross-reference numbers. Often replaced together with the drum belt (341241) and drum support rollers (349241T) as the 4392065 maintenance kit. Installs in 30–45 minutes with basic hand tools. Quick Answer The XPARTCO 691366 Dryer Idler Pulley Assembly fixes Whirlpool-family dryers that are squealing, thumping, or where the drum stops spinning because the belt has lost tension. Complete arm and pulley assembly. 6"L x 1-5/8"W x 3-7/8"H overall, 1-7/8" pulley diameter. Replaces older Teflon friction pulleys with ball-bearing wheel. Compatible with Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, and more. Replaces WP691366, 239477, 337116, 3394332, 347034, AP6010582, PS11743765. Often replaced with 341241 belt and 349241T rollers. Common Problems This Part Fixes Drum not spinning — belt has lost tension and slipped off the motor pulley Loud squealing or squeaking noise during the drying cycle — worn idler pulley bearing Thumping or clunking noise as the pulley wheel wobbles on a worn bearing Belt repeatedly slipping or falling off after being reinstalled Grinding noise from the idler pulley area — bearing fully failed Dryer drum spinning intermittently due to inconsistent belt tension Idler pulley arm visibly cracked, broken, or wheel no longer spinning freely Replaces Part Numbers This idler pulley assembly directly replaces the following OEM and cross-reference part numbers: WP691366, 691366, 239477, 26000691366, 337116, 337407, 337510, 3388345, 338946, 3394332, 347034, 347226, 347277, 4319391, 688166, 691366BULK, 8207, 99989677, DE412, K35-163, W10612905, WP691366VP, AWP48059, EAP11743765, AP6010582, PD00002256, PS11743765. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This idler pulley assembly is compatible with select gas and electric dryers from the following brands — particularly models with the lint filter on top: Whirlpool dryers (gas and electric — WED, WGD, LE, LG, and related series with top lint filter) Kenmore / Sears dryers (Whirlpool-built models) Maytag dryers (gas and electric) Amana dryers KitchenAid dryers Roper dryers Crosley dryers Estate dryers Inglis dryers Admiral dryers Magic Chef dryers Norge dryers Note: The 691366 idler pulley is for older Whirlpool-family dryers with the lint filter on top. Newer Whirlpool dryers with the lint screen inside the door use the W10837240 idler pulley arm assembly instead. Always verify your model number before ordering. Key Features Complete idler arm and pulley assembly — includes both the spring-tensioned arm and the pulley wheel Maintains correct drive belt tension so the belt grips the drum and motor pulley without slipping Redesigned ball-bearing pulley wheel replaces older Teflon friction-style pulleys for longer service life and quieter operation Overall dimensions: 6"L x 1-5/8"W x 3-7/8"H; pulley wheel diameter: 1-7/8" Plastic arm with metal shaft and ball-bearing pulley wheel Replaces WP691366, 239477, 337116, 3394332, 347034, AP6010582, and over 30 additional cross-reference numbers Compatible with 12 major appliance brands on the Whirlpool top-lint-filter platform Often replaced together with the drum belt (341241) and drum rollers (349241T) — all three included in the 4392065 maintenance kit Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 30–45 minutes with basic hand tools Product Specifications Part Number 691366 OEM Part Number WP691366 Part Type Dryer Idler Pulley Assembly (Arm and Wheel) Condition Aftermarket Replacement Application Gas and Electric Dryers (lint filter on top models) Overall Dimensions 6"L x 1-5/8"W x 3-7/8"H Pulley Wheel Diameter 1-7/8 inches Material Plastic arm / Metal shaft / Ball-bearing pulley wheel Color Black / White Includes Complete idler arm and pulley assembly Often Replaced With 341241 Drum Belt, 349241T Drum Rollers (4392065 kit) Compatible Brands Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Crosley, Estate, Inglis, Admiral, Magic Chef, Norge Installation Notes ⚠️ Unplug Dryer Before Starting Disconnect power (and shut off gas for gas dryers) before beginning. Remove the lint screen and unscrew the screws inside the lint screen housing. Use a putty knife to release the top panel spring clips and lift the top panel. Remove the front panel to fully access the drum drive components. Release belt tension by pushing the idler pulley arm toward the motor and sliding the belt off. Note how the belt is routed before removing — take a photo. Unclip or unscrew the old idler pulley assembly from its mounting bracket. Install the new 691366 idler pulley in the same position. Re-route the belt around the drum (ribbed side in), under the idler pulley, and around the motor pulley, then release the idler arm to create tension. Reassemble the front and top panels, restore power, and run a test cycle. Tip: while the dryer is open, inspect and replace the drum belt (341241) and drum support rollers (349241T) if worn. Tools needed: Phillips screwdriver, 1/4" or 5/16" nut driver, putty knife. Frequently Asked Questions What does the idler pulley do? The idler pulley is a spring-loaded arm and wheel assembly that presses against the drive belt between the drum and the motor pulley, keeping the belt under constant tension. This tension is what allows the belt to grip both the drum and the motor pulley without slipping as the motor spins. Without proper tension — or with a pulley bearing that has failed — the belt slips, the drum stops spinning, and the dryer produces heat but does not tumble clothes. A worn bearing also creates the high-pitched squealing sound that is the most common sign of idler pulley failure. What is the difference between 691366 and WP691366? These are the same idler pulley assembly. WP691366 is the updated Whirlpool OEM part number that superseded the original 691366. The W10612905 is also a cross-reference for the same assembly. This aftermarket replacement is compatible with all three numbers. What is the difference between 691366 and W10837240? Both are Whirlpool dryer idler pulley assemblies, but for different dryer generations. The 691366 (WP691366) is used on older Whirlpool-family dryers with the lint filter on top of the dryer. The W10837240 is a larger, redesigned idler arm and bracket assembly used on newer Whirlpool-family dryers with the lint screen inside the door. They are not interchangeable. Always verify your model number to confirm which idler pulley is correct for your dryer. Should I also replace the belt and drum rollers at the same time? Yes — since the dryer must be disassembled to replace the idler pulley, this is the ideal time to also inspect and replace the drum belt (341241) and rear drum support rollers (349241T). All three parts are part of the same drum drive system and wear at similar rates. The 4392065 maintenance kit includes all three together and is the recommended approach for a complete drum drive repair — one teardown covers everything. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured from durable plastic and metal with a ball-bearing pulley wheel to match the dimensions and performance of the original WP691366 idler pulley assembly. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

ERP 3977767 Dryer Hi Limit Thermostat 250 -80F Limit Thermostat. Fits specific Maytag, Kenmore, Whirlpool dryer models. Replaces Part Number: WP3977767, 3977767, 3399693, ER3977767, SET185, TJ90SET185, WP3977767VP, AP6009043, PS11742185. Description: This Hi-Limit Thermostat is a replacement part for specific Maytag, Kenmore, Whirlpool dryer models. It functions as a critical safety device that monitors and controls the temperature within the dryer, preventing it from overheating. When the dryer reaches a temperature that is too high, this thermostat will cut off the power to the heating element to mitigate the risk of fire.   This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

XPARTCO WR49X10173 Refrigerator Dispenser Heater – Compatible with GE, Hotpoint & Kenmore Refrigerators Product Description Restore proper ice and water dispenser operation with the XPARTCO WR49X10173 Refrigerator Dispenser Heater. This high-quality aftermarket replacement heater prevents ice buildup and freezing inside the dispenser chute by gently warming the dispenser area. A failed dispenser heater can cause ice clogs, frozen chute doors, or dispensing issues. Replacing it with this reliable XPARTCO heater helps ensure smooth ice dispensing and consistent refrigerator performance. Replaces Part Numbers WR49X10173, 1381601, AH1766223, PD00001237, FIX1766223, AP4318572, EA1766223, PS1766223.  Compatibility This replacement refrigerator dispenser heater fits select GE, Hotpoint, and Kenmore (GE-manufactured) side-by-side refrigerators. Description: Dispenser water spout heater kit. For models that start with BSS, DSS, ESH, GSH, GSS, GST, HSS, and SSS with serial# AF - AM. Built between January 2003 - January 2007. Example compatible models include (but are not limited to):GE GSS25GSHSS, GSH25JSDBSSHotpoint HSS25GFTSAKenmore 363.9557710 Always verify your refrigerator’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM heating performance ❄️➡️🔥 Prevents Ice Buildup – Keeps dispenser chute clear and functional ⚡ Efficient Heating Element – Maintains proper dispenser temperature 💰 Cost-Effective Repair – Reliable alternative to OEM heater pricing 🛡️ Fixes Common Issues – Solves frozen dispenser, ice clogs, or slow dispensing 📐 Product Specification Part Number: WR49X10173 Component Type: Refrigerator Dispenser Heater Voltage: 120V AC Application: Ice and water dispenser chute heating Mounting: Direct-fit installation Material: Insulated heating element with OEM-equivalent wiring Quality Level: Aftermarket replacement (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver ⚠️ Safety First: Unplug the refrigerator before servicing to avoid electrical shock. Steps: Disconnect power from the refrigerator. Remove the dispenser front panel. Locate the dispenser heater assembly. Disconnect wiring and remove the old heater. Install the new XPARTCO WR49X10173 heater. Reconnect wiring, reassemble the dispenser panel, and restore power. Test dispenser operation. ⏱️ Time Required: 15–20 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Restore smooth ice dispensing and prevent freeze-ups — Add to Cart Now for a dependable, budget-friendly repair!

Read more less

279570 Genuine OEM Whirlpool Dryer Door Catch Kit The 279570 is a Genuine OEM Whirlpool dryer door catch and strike kit compatible with a wide range of Whirlpool, Kenmore, Roper, Estate, Amana, Crosley, Inglis, KitchenAid, Maytag, and Admiral dryers. The door catch is the spring-clip mechanism on the dryer door that snaps over the door strike to hold the door firmly closed during operation, activating the door switch so the dryer can run. When the catch breaks, wears out, or loses tension, the door will not stay closed, the door switch will not be activated, and the dryer will either not start or will stop mid-cycle. The strike is the corresponding post or tab on the dryer cabinet that the catch engages. This Genuine OEM kit includes three color-coded door catches of different tensions and two metal door strikes, plus one screw. Because the tension of the catch must match the original, Whirlpool includes three options in the kit — each is color-coded and numbered on the back. Refer to identify which catch is correct for your model. The kit directly replaces a very large list of older cross-reference numbers including 279570VP, 3493, 2003, 8208, 279280, 279337, 696144, 693717, AP3094183, PS334230, and dozens more. Installs in under 15 minutes with a Phillips screwdriver. Quick Answer The 279570 Genuine OEM Whirlpool Dryer Door Catch Kit fixes dryers where the door won't stay closed, pops open mid-cycle, or won't activate the door switch to start. Kit includes 3 color-coded catches (different tensions), 2 metal strikes, 1 screw. Use the catch that matches your original. Genuine OEM. Compatible with Whirlpool, Kenmore, Roper, Estate, Amana, Crosley, Inglis, KitchenAid, Maytag, and Admiral dryers. Installs in under 15 minutes. Common Problems This Kit Fixes Dryer door will not stay closed during the drying cycle Door pops open mid-cycle, stopping the dryer Dryer will not start — door switch not being activated by a worn or broken catch Door feels loose or does not click shut firmly when closed Door catch visibly cracked, broken, or missing Door strike bent or missing — door cannot engage the catch properly Dryer requires the door to be held or pushed closed to stay running Replaces Part Numbers This door catch kit directly replaces the following OEM and cross-reference part numbers: 279570, 14205029, 14205577, 14210022, 2003, 236876, 236877, 241282, 241890, 26000279570, 261847, 263067, 279280, 279337, 279469, 279570VP, 291949, 3390239, 3392538, 3398175, 342295, 347813, 3493, 4165234, 51651001, 51655001, 66021, 690081, 690082, 693717, 694343, 696144, 8208, 830751, 834767, 834813, 834943, 834944, AH334230, DE902, EA334230, EAP334230, FSP279570, AP3094183, AWP39897, PD00002346, PS334230. Contact our support team with your model number if you need confirmation before ordering. Compatibility This door catch kit is compatible with select dryers from the following brands: Whirlpool dryers (gas and electric) Kenmore / Sears dryers (Whirlpool-built models) Roper dryers Estate dryers Amana dryers Crosley dryers Inglis dryers KitchenAid dryers Maytag dryers Admiral dryers Important: This kit includes three catches with different spring tensions, color-coded and numbered on the back. You must use the catch that matches the tension of your original. Using the wrong tension catch may result in a door that is too hard to open or too easy to pop open. Key Features Genuine OEM kit manufactured by Whirlpool to factory specifications — guaranteed fit and performance Holds the dryer door closed and activates the door switch so the dryer can run safely Kit includes 3 color-coded door catches (different spring tensions), 2 metal door strikes, 1 screw Catches are color-coded and numbered on the back — use the one that matches your original. Plastic catches with metal strikes and metal screw — durable construction for long service life Consolidates a very large list of older Whirlpool-family door catch cross-reference numbers Compatible with 10 major appliance brands on the Whirlpool platform Quick DIY repair — installs in under 15 minutes with a Phillips screwdriver Product Specifications Part Number 279570 Part Type Dryer Door Catch and Strike Kit Condition Genuine OEM Application Gas and Electric Dryers Kit Includes 3 color-coded door catches (different tensions), 2 metal strikes, 1 screw Material Plastic catches / Metal strikes Color White / Silver Catch Selection Color-coded and numbered, Use the catch that matches your original Compatible Brands Whirlpool, Kenmore, Roper, Estate, Amana, Crosley, Inglis, KitchenAid, Maytag, Admiral Installation Notes ⚠️ Unplug Dryer Before Starting Disconnect power before beginning. using the wrong tension catch will result in incorrect door resistance. Open the dryer door and locate the old door catch on the inside of the door panel and the strike on the dryer cabinet opening. To remove the old catch: press the retaining tabs and pull the catch free from its slot, or unscrew the mounting screw. Install the correct new catch into the same position. To replace the strike: remove the old strike (typically held by a single screw) and install the new strike in the same position. Close the dryer door to confirm it latches firmly with a satisfying click. Restore power and run a short test cycle to confirm the door stays closed and the dryer operates normally. Tools needed: Phillips screwdriver; needle-nose pliers may help with catch removal on some models. Frequently Asked Questions Why does the kit include three different catches? Whirlpool used door catches with different spring tensions across its dryer lineup — a lighter catch on some models and a stiffer catch on others. To cover all compatible models in a single kit, Whirlpool includes three catches of different tensions, each color-coded and numbered on the back. It is important to use the correct one — using a catch with too little tension may allow the door to pop open, while a catch with too much tension may make the door difficult to open. Do I need to replace both the catch and the strike, or just one? It depends on which component has failed. The catch (the spring-clip on the door) is the more commonly replaced part — it wears out from repeated use faster than the strike. Inspect both: if the catch is cracked or has lost its spring tension, replace the catch. If the strike is bent, cracked, or missing, replace the strike. Since the kit includes both catches and strikes, you have everything needed for a complete repair. When in doubt, replacing both ensures the full latch system is renewed. My dryer will not start even after replacing the door catch — what else could it be? If the dryer still will not start after the catch is replaced, the door switch may also need to be tested. The door switch is the electrical component that the door catch activates when the door closes — if the switch itself is failed, replacing the catch alone will not restore function. Test the door switch (3406105 for most Whirlpool-family models) with a multimeter for continuity in both the open and closed positions. If the switch reads open in both positions or closed in both positions, it has failed and needs replacement. How is the 279570 different from the W11429587 dryer door catch? The 279570 is the door catch kit for older Whirlpool-family dryers — it includes multiple catches of different tensions and metal strikes because it covers a wide range of older models. The W11429587 is a single snap-in door catch for newer Whirlpool-family dryers (Cabrio and newer platform models). If your dryer is a newer model with a snap-in catch slot rather than a screw-mounted catch and strike, you likely need the W11429587. Verify your model number to confirm which part is correct. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM kit manufactured by Whirlpool to factory specifications. It is the exact same door catch and strike kit supplied by Whirlpool for compatible dryer service repairs — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 279457 Dryer Heating Element Wire Kit – Compatible with Whirlpool, Maytag & Kenmore Dryers Product Description Restore safe electrical connections and proper heating performance with the XPARTCO 279457 Dryer Heating Element Wire Kit. This high-quality aftermarket replacement kit is designed to repair damaged or burnt wiring at the dryer heating element. Over time, high heat can cause wire terminals to melt or loosen, leading to no-heat issues or intermittent operation. Replacing the wiring with this durable XPARTCO kit helps ensure secure connections and reliable dryer performance. Note: Includes two high-temperature wires and two wire connectors (female spade connectors, 5/16"). Disconnect power before installation. Verify compatibility with your dryer model. Replaces Part Numbers 279457, 279457VP, 3140, T2502, AP3134638, PS334206. Compatibility This replacement dryer heating element wire kit fits select Whirlpool, Maytag, Kenmore, Amana, Estate, Roper, and Crosley electric dryers. Example compatible models include (but are not limited to): Whirlpool WED4800BQ0, WED4800XQ0, WED4850BW0, WED4900XW0, WED5321SQ0 Maytag, Kenmore, Amana, Admiral, Jenn-Air, Roper, Estate (verify compatibility with heating element 4391960) MEDC215EW1, MEDC400VW0 Kenmore 110.6012010, 110.60072990 Always verify your dryer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement Kit – Matches OEM wire gauge and terminal design 🔥 Heat-Resistant Wiring – Designed for high-temperature dryer environments 🔧 Secure Electrical Connections – Helps prevent arcing and power loss 💰 Cost-Effective Repair – Reliable alternative to OEM wire kits 🛡️ Fixes Common Issues – Resolves no-heat problems caused by burnt wires 📐 Product Specification Part Number: 279457 Component Type: Dryer Heating Element Wire Kit (2 Wire and 2 Wire Connector) Includes: High-temperature wires with factory-style terminals Application: Heating element electrical connections Material: Heat-resistant insulated wiring with metal connectors Quality Level: Aftermarket replacement (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver, needle-nose pliers ⚠️ Safety First: Always unplug the dryer before servicing to avoid electrical shock. Basic Steps: Disconnect dryer power. Remove the rear access panel. Locate the heating element terminals. Remove damaged or burnt wires. Install the new XPARTCO 279457 wire kit securely. Reassemble the dryer and restore power. Test dryer heating operation. ⏱️ Time Required: 15–25 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Aftermarket Appliance Parts 🔄 30-Day Return Policy Restore safe dryer heating connections — Add to Cart Now for a dependable, budget-friendly repair!

Read more less

XPARTCO 6931EL3001E Dryer Thermostat – Compatible with LG and Kenmore Dryers Product Description Maintain proper dryer safety and temperature control with the 6931EL3001E Dryer Thermostat. This replacement part monitors and regulates dryer temperature to prevent overheating and ensure efficient drying cycles. A faulty thermostat may cause your dryer to stop heating, overheat, or shut off unexpectedly. Replacing it restores reliable performance and helps extend the life of your dryer. Replaces Part Numbers 6931EL3001E, 1268363, 6931EL3001B, 6931EL3001C, AH3530481, EA3530481, PD00023869, EAP3530481, AP4440977, PS3530481, L125-31C, 503475. Compatibility This dryer thermostat is compatible with select LG and Kenmore dryer models. Example compatible models include (but are not limited to): LG DLE2516W, DLE7177WM, and Kenmore 796.80272900. Always verify your dryer’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Broad Compatibility – Fits select LG and Kenmore dryers 🔒 Reliable Safety – Prevents overheating by regulating dryer temperature 💰 Cost-Effective Replacement – OEM-equivalent performance at a lower price 🛠️ DIY-Friendly – Quick installation with basic tools 🛡️ Fixes Common Issues – Restores heating, prevents overheating, and fixes dryer shutdown problems 📐 Product Specification Part Number: XP6931EL3001E Component Type: Dryer Thermostat Material: High-heat resistant metal and thermal components Mounting: Direct replacement, mounts on heating element housing Operating Conditions: Designed for residential dryers Compliance: OEM-equivalent performance and safety standards 🛠️ Installation Notes Tools Needed: Phillips screwdriver, flathead screwdriver, needle-nose pliers ⚠️ Safety First: Always disconnect power before starting repairs to avoid electrical shock. Steps: Unplug dryer and remove back access panel. Locate thermostat on heating element housing. Disconnect wire terminals from the old thermostat. Remove screws holding it in place and replace with the new thermostat. Reconnect wires, secure the component, and reinstall the access panel. Restore power and test dryer operation. ⏱️ Time Required: 15–20 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders 🛠️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Restore your dryer’s safe operation today — Add to Cart Now for fast, budget-friendly repair!

Read more less

XPARTCO WR07X10131 Refrigerator Compressor Overload Relay Replaces Part Numbers: WR07X10131, WR08X10074, WR08X10089, WR08X10111, WR09X10124, AH2577842, EA2577842, AP4538934, PS2577842. Description:  This Start Device Assembly is a replacement part for Specific GE refrigerator models. It is a kit that includes the start relay and overload, both of which are crucial components for the proper operation of the compressor. The start relay is responsible for initiating the compressor's operation by providing an electrical boost to start the motor. The overload, on the other hand, acts as a protective device. It monitors the current flow and protects the compressor from overheating or electrical overload.   This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

XPARTCO AJU75152602 Washer Water Inlet Valve The XPARTCO AJU75152602 is an aftermarket replacement washer water inlet valve assembly compatible with select LG and Kenmore top-load washers in the larger-capacity WT7 series — including the WT7060, WT7100, WT7150, WT7155, WT7250, WT7300, WT7305, WT7400, WT7405, WT7800, WT7880, and WT7900 series. The water inlet valve is a multi-port solenoid valve mounted on the back of the washer that controls the flow of hot and cold water into the tub and dispenser compartments during fill and rinse cycles. When any valve port fails, the washer may not fill at all, fill too slowly, fill with the wrong water temperature, overfill, or leak from the valve body. This valve assembly directly replaces 5221EA1008S, 4873914, AP6335382, EAP12580369, PS12580369, and PD00060681. It includes two integrated inlet screens to filter debris from the supply lines. Installs in 15–25 minutes with basic hand tools. Note: the AJU75152602 is for the WT7xxx larger-capacity LG top-load series — it is not the same valve as the AJU75152601, which is used on the earlier and smaller-capacity WT1xxx through WT5xxx series. Verify your model number before ordering. Quick Answer The XPARTCO AJU75152602 Washer Water Inlet Valve fixes LG WT7xxx-series top-load washers that won't fill, fill slowly, fill with wrong temperature, overfill, or leak from the valve. Includes 2 inlet screens. Replaces 5221EA1008S, 4873914, AP6335382, EAP12580369, PS12580369, PD00060681. Compatible with LG WT7060, WT7100, WT7150, WT7300, WT7305, WT7400, WT7405, WT7800, WT7880, WT7900 series and Kenmore (LG-built). Note: not the same as AJU75152601 — different model series. Common Problems This Part Fixes Washer not filling with water at all when a cycle is started Washer filling very slowly — taking much longer than normal to reach water level Washer filling with only cold water on a warm or hot cycle — hot solenoid failed Washer filling with only hot water on a cold cycle — cold solenoid failed Washer overfilling or filling continuously — valve port stuck open Water temperature incorrect despite correct cycle selection Water dripping into the tub between cycles — valve not sealing completely Water leaking from the back of the washer near the valve body Replaces Part Numbers This water inlet valve directly replaces the following OEM and cross-reference part numbers: AJU75152602, 4873914, 5221EA1008S, U8EONG(9F), IV-248-103, PD00060681, FIX12580369, ALG53788, AP6335382, PS12580369, DC12V 6W, IV-248-103, U8EONG(9F). If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water inlet valve is compatible with select LG WT7 series top-load washers and related Kenmore models: LG WT7060CV, WT7060CW LG WT7100CW LG WT7150CW, WT7155CW LG WT7250CW LG WT7300CV, WT7300CW LG WT7305CV, WT7305CW LG WT7400CV, WT7400CW LG WT7405CV, WT7405CW LG WT7800CV, WT7800CW LG WT7880HWA LG WT7900HBA Kenmore 31452 and select LG-built Kenmore models Important — AJU75152602 vs AJU75152601: These are two different valves for different LG washer generations. The AJU75152602 is for the larger-capacity WT7xxx series. The AJU75152601 is for the earlier and smaller-capacity WT1xxx through WT5xxx series. They are not interchangeable. Always verify your model number before ordering. Key Features Multi-port solenoid valve — controls hot water, cold water, and dispenser ports to deliver the correct water temperature and volume for each cycle phase Includes two integrated inlet screens — filter debris and mineral deposits from the supply lines before they reach the valve seat ABS plastic and stainless steel construction — durable and resistant to mineral buildup and corrosion Replaces 5221EA1008S, 4873914, AP6335382, EAP12580369, PS12580369, and PD00060681 Compatible with LG WT7060, WT7100, WT7150, WT7300, WT7305, WT7400, WT7405, WT7800, WT7880, WT7900 series and Kenmore LG-built models For WT7xxx series only — not the same as AJU75152601 (WT1xxx–WT5xxx series) Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 15–25 minutes with basic hand tools Product Specifications Part Number AJU75152602 Part Type Washer Water Inlet Valve Assembly (Multi-Port) Condition Aftermarket Replacement Application LG WT7xxx Series Top-Load Washers Material ABS plastic / Stainless steel Kit Includes Valve assembly + 2 integrated inlet screens Note WT7xxx series only — not interchangeable with AJU75152601 (WT1xxx–WT5xxx) Compatible Brands LG, Kenmore (LG-built) Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off both the hot and cold water supply valves before beginning. Pull the washer away from the wall to access the back panel. The water inlet valve is mounted on the upper rear of the washer. Photograph all wire harness connections and hose positions before disconnecting. Disconnect the two external supply hoses from the valve inlet ports. Disconnect the internal outlet hoses by squeezing the retaining clips and pulling free. Disconnect the wiring harness connectors from each solenoid port. Unscrew the mounting screws and remove the old valve. Install the new AJU75152602 valve in the same position, reconnect all internal hoses, wire harnesses, and external supply hoses in the documented positions. Restore water supply and power, then run a fill cycle to verify normal filling and check for leaks. Tools needed: Phillips screwdriver, pliers. Frequently Asked Questions What is the difference between AJU75152602 and AJU75152601? These are two different water inlet valve assemblies for different generations of LG top-load washers. The AJU75152601 (which also replaces AJU73213301 and 5221EA1008F) is used on LG's earlier and smaller-capacity top-load washers in the WT1xxx, WT4xxx, and WT5xxx series. The AJU75152602 (which replaces 5221EA1008S) is for LG's larger-capacity WT7xxx series. Despite appearing similar, they have different port configurations and are not interchangeable. Always verify your specific model number before ordering. How do I know if the water inlet valve has failed? Common signs are the washer not filling, filling only on one temperature setting, overfilling, dripping between cycles, or leaking from the valve area. Before replacing the valve, check that both supply valves are fully open and the hoses are not kinked. You can test each solenoid coil with a multimeter — a working coil shows resistance (typically 200–500 ohms); an open circuit confirms that coil has failed. Also inspect and clean the inlet screens inside the supply port openings — mineral-clogged screens can restrict flow enough to cause the same symptoms as a failed valve. What are the two inlet screens included with the valve? The two mesh screens that come with the AJU75152602 install inside the hot and cold water inlet ports of the valve. They catch sediment, mineral particles, and debris from the household water supply before they can reach the solenoid valve seats. Installing fresh screens along with the new valve helps extend the valve's service life, especially in areas with hard water. If the previous valve failed due to mineral buildup rather than an electrical fault, cleaning the supply hoses before installation is also recommended. My LG WT7300CW is only filling with cold water — is this the valve? Filling with only cold water on a warm or hot cycle is a classic sign that the hot water solenoid coil on the inlet valve has failed. Each temperature port is controlled by its own independent solenoid — when the hot solenoid fails, only the cold port opens. Before replacing the valve, also confirm that the household hot water supply valve is fully open and that hot water is reaching the back of the washer in the supply hose. If hot water supply is confirmed and the cold-only fill persists, replace the AJU75152602 valve. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine LG OEM part, but is manufactured from ABS plastic and stainless steel to match the port configuration and specifications of the original AJU75152602 water inlet valve assembly. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XP382 Dryer Dryer Gas Valve Solenoid Fits Samsung Dryer Gas Valve Coils Kit for DC62-00201A   Description: This Dryer Gas Valve Coil Kit is a replacement part for Specific Kenmore, Samsung Gas dryer models. It is a set of coils that control the flow of gas fuel to the burner. The gas valve regulates the precise amount of gas needed to properly combust and generate heat for drying clothes.   This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

W11700916 Washer Genuine OEM Door Latch – Compatible with Whirlpool, Maytag, Amana, and Crosley Washers Product Description Ensure your washer door locks securely and operates safely with the W11700916 Washer Genuine OEM Door Latch. This factory-approved latch assembly detects whether the washer door is closed and locks it during operation to prevent leaks or accidental openings. A faulty latch can cause error codes, interrupted cycles, or prevent the washer from starting. Replacing it with this genuine OEM part restores proper function and reliable performance. Replaces Part Numbers W11700916, W11394572, W11032875, W11543566, PD00085319, EAP17217010, AP7219279, PS17217010.  Compatibility This genuine door latch is compatible with select Whirlpool, Maytag, Amana, and Crosley front-load washers. Example compatible models include (but are not limited to): Whirlpool WFW5605MW0, Maytag MHW5630HW3, and Amana NFW5800HW0. Always verify your washer’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Genuine OEM Replacement – Factory-tested latch for Whirlpool-brand washers 🔒 Secure Door Locking – Prevents accidental opening during wash cycles 💰 Reliable & Durable – Genuine OEM construction for long service life 🛠️ DIY Installation – Installs easily with basic tools in under 30 minutes 🛡️ Fixes Common Issues – Resolves door lock error codes and cycle interruptions 📐 Product Specification Part Number: W11700916 Component Type: Washer Door Latch Assembly Material: Reinforced plastic housing with electrical switch and locking mechanism Mounting: Direct-fit replacement Operating Conditions: Designed for residential front-load washers Compliance: Genuine OEM certified 🛠️ Installation Notes Tools Needed: Phillips screwdriver, Torx driver ⚠️ Safety First: Always unplug the washer before starting repairs to prevent electrical shock. Steps: Disconnect washer from power. Open the door and remove the retaining ring securing the door boot seal. Pull back the seal to access the latch assembly. Remove screws holding the old latch in place. Disconnect the wire harness and remove the latch. Install the new W11700916 latch, reconnect wires, and secure with screws. Reattach the boot seal and retaining ring, then restore power. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders 🛠️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Solve door lock errors and restore safe washer operation — Add to Cart Now for a factory-approved repair!

Read more less

XPARTCO 4681JB1029A Refrigerator Evaporator Fan Motor – Compatible with LG and Kenmore Refrigerators Product Description Keep your refrigerator cooling evenly with the XPARTCO 4681JB1029A Refrigerator Evaporator Fan Motor. This Fan Motor is a replacement component for specific LG, Kenmore refrigerator models. It operates the circulation fan located in the back of the refrigerator compartment, distributing cool air evenly throughout. The motor enables constant airflow across shelves and compartments to maintain consistent temperatures and humidity levels. Causes of a bad fan motor include failure of bearings or windings due to prolonged use. Replaces Part Numbers 4681JB1029A, EAU60694507, 1330410, 4681JB1010C, 4681JB1017A, 4681JB1017D, 4681JB1027A, EAU61762902, EAU41921810, PD00037982, EAP3523328, AH3523328, EA3523328, AP4438221, PS3523328.  Compatibility This replacement evaporator fan motor fits select LG and Kenmore refrigerators. Example compatible models include (but are not limited to): LG LFX25960ST, LG LFX28968ST, and Kenmore 795.77543600. Always verify your refrigerator’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Built to meet OEM airflow and reliability standards ❄️ Efficient Air Circulation – Distributes cold air evenly through refrigerator and freezer 💰 Affordable Solution – Quality replacement at a lower cost than OEM parts 🛠️ DIY Installation – Simple plug-in wiring connector for quick installation 🛡️ Fixes Common Issues – Solves frost buildup, uneven cooling, or noisy fan problems 📐 Product Specification Part Number: 4681JB1029A Component Type: Refrigerator Evaporator Fan Motor Material: Metal motor housing with balanced plastic fan blade Mounting: Direct-fit replacement in freezer evaporator compartment Operating Conditions: Designed for continuous low-temperature operation Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver ⚠️ Safety First: Always unplug the refrigerator before performing repairs to prevent electrical shock. Steps: Unplug the refrigerator. Remove shelves and freezer rear panel to access the evaporator area. Disconnect the wiring harness and mounting screws on the old fan motor. Install the new XPARTCO 4681JB1029A motor, reconnect wiring, and secure the panel. Restore power and verify quiet, consistent airflow. ⏱️ Time Required: 20–25 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Restore efficient, even cooling — Add to Cart Now for a reliable, budget-friendly repair!

Read more less