Appliance Parts

W11457841 Genuine OEM Whirlpool Washer Lid Strike The W11457841 is a Genuine OEM Whirlpool replacement washer lid strike compatible with select Whirlpool, Maytag, and Kenmore HE top-load washers — including the Whirlpool WTW5100, WTW5105, WTW6120, WTW7120, WTW8120, WTW8127 series, and the Maytag MVW6200, MVW6230, MVW7230, MVW7232, MVW8230 series. The lid strike is the plastic component attached to the underside of the washer lid that physically engages the lid lock mechanism when the lid is closed. As the lid lowers into place, the strike enters the lock slot and activates the lid switch — signaling the control board that the lid is securely closed and the washer is safe to start agitation and spin. When the lid strike fails — typically by breaking off, cracking, or wearing down — the lid lock can't be properly activated, and the washer will not start, will stop mid-cycle, or will refuse to advance to the spin cycle. As a Genuine OEM part manufactured by Whirlpool to factory specifications, the W11457841 is the current production part, directly superseding W11091027. It also replaces 4959179, AP6987306, EAP16218028, PD00061788, and PS16218028. Installation is fast and simple — a counterclockwise twist removes the old strike, and a clockwise twist installs the new one. Installs in under 5 minutes, no special tools required. Quick Answer The W11457841 Genuine OEM Whirlpool Washer Lid Strike fixes Whirlpool, Maytag, and Kenmore HE top-load washers that won't start, won't lock the lid, stop mid-cycle, or won't advance to spin because the lid strike is broken or worn. Plastic strike that attaches to the underside of the washer lid and activates the lid lock and switch. Twist-in installation. Genuine OEM. Replaces W11091027, 4959179, AP6987306, EAP16218028, PD00061788, PS16218028. Compatible with Whirlpool WTW5100/5105/6120/7120/8120/8127 and Maytag MVW6200/6230/7230/7232/8230 series. Common Problems This Part Fixes Washer not starting — lid strike not engaging the lid lock Lid won't lock at the start of the cycle Washer stops mid-cycle with a lid-related fault Washer fills with water but won't agitate or advance to spin Lid strike visibly broken, cracked, or missing on the underside of the lid Strike worn down — physically fits the lock slot but no longer activates the lid switch Repeated lid lock errors despite the lid appearing to close normally Replaces Part Numbers This washer lid strike directly replaces the following OEM and cross-reference part numbers: W11457841, W11091027, AP6987306, AWP44638, PD00061788, EAP16218028, PS16218028. W11457841 is the current production part superseding W11091027. Contact our support team with your model number if you need confirmation before ordering. Compatibility This lid strike is compatible with select HE top-load washers from the following brands and series: Whirlpool top-load washers — WTW5100HC0, WTW5100HC1, WTW5100HC2, WTW5100HW0, WTW5100HW1, WTW5100HW2 series Whirlpool top-load washers — WTW5105HC0, WTW5105HC1, WTW5105HC2, WTW5105HW0, WTW5105HW1, WTW5105HW2 series Whirlpool top-load washers — WTW6120HC0, WTW6120HC1, WTW6120HC2, WTW6120HW0, WTW6120HW1, WTW6120HW2 series Whirlpool top-load washers — WTW7120HC0, WTW7120HW0 series Whirlpool top-load washers — WTW8120HC0, WTW8120HW0 series Whirlpool top-load washers — WTW8127LC0, WTW8127LC1, WTW8127LW0 series Maytag top-load washers — MVW6200KW0, MVW6200KW1, MVW6200KW2, MVW6200KW3 series Maytag top-load washers — MVW6230HC0, MVW6230HC1, MVW6230HC2, MVW6230HW0, MVW6230HW1, MVW6230HW2 series Maytag top-load washers — MVW6230RHW0, MVW6230RHW1, MVW6230RHW2 series Maytag top-load washers — MVW7230HC0, MVW7230HW0, MVW7230HW1 series Maytag top-load washers — MVW7232HC0, MVW7232HW0, MVW7232HW2 series Maytag top-load washers — MVW8230HC0 series Kenmore / Sears top-load washers (Whirlpool-built — select 110-series models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Genuine OEM part manufactured by Whirlpool to factory specifications — guaranteed fit and performance Plastic strike attaches to the underside of the washer lid and engages the lid lock mechanism when the lid closes Activates the lid switch to signal the control board that the lid is securely closed and the washer is safe to start Twist-in/twist-out installation — no tools or hardware required; counterclockwise to remove, clockwise to install Current production part — directly supersedes W11091027 Replaces W11091027, 4959179, AP6987306, EAP16218028, PD00061788, and PS16218028 Compatible with Whirlpool WTW5100/5105/6120/7120/8120/8127 and Maytag MVW6200/6230/7230/7232/8230 series HE top-load washers, plus select Kenmore Whirlpool-built models Fast DIY repair — installs in under 5 minutes Product Specifications Part Number W11457841 Supersedes W11091027 Part Type Washer Lid Strike Condition Genuine OEM Application HE Top-Load Washers (Whirlpool/Maytag/Kenmore platform) Material High-strength plastic Installation Twist-in (clockwise) / twist-out (counterclockwise) — no tools required Mounting Location Underside of washer lid Compatible Brands Whirlpool, Maytag, Kenmore Installation Notes ⚠️ Unplug Washer Before Starting — Wear Work Gloves Disconnect power before beginning. Wear work gloves to protect your hands. Open the washer lid and locate the lid strike on the underside of the lid — it's the small plastic peg that drops into the lock slot when the lid is closed. To remove the old strike: rotate the strike counterclockwise until the retaining tab breaks free and pulls back, then pull the old strike straight out. To install the new W11457841: align it with the mounting hole in the same orientation as the old one, and rotate clockwise until you hear or feel the retainer tab click into place. Close the lid and confirm the strike engages the lock slot properly. Restore power, start a test cycle, and confirm the lid locks and the washer begins normal operation. Tools needed: work gloves only — no tools required for the strike itself. Frequently Asked Questions What's the difference between the lid strike, lid lock, and lid switch? These three components work together as a safety system. The lid strike (W11457841) is the small plastic peg attached to the underside of the lid that physically enters the lock slot when the lid closes. The lid lock is the mechanism in the washer cabinet that grips the strike and physically locks the lid closed during the spin cycle. The lid switch is the electrical sensor inside the lock assembly that signals the control board when the strike is engaged. If the strike is broken or missing, none of the three can do their job — even if the lock and switch are working perfectly. Replacing just the strike often resolves "won't start" issues without needing to replace the more expensive lock assembly. What is the difference between W11457841 and W11091027? These are the same lid strike across production revisions. W11091027 was the earlier OEM part number, and W11457841 is the current production version that Whirlpool issued as a direct replacement. Both parts are physically and functionally identical — if your washer's parts diagram shows W11091027, the W11457841 is the correct current replacement, and this listing covers both numbers. My washer won't start and the lid seems to close normally — could this be the strike? Yes, this is one of the most common symptoms of lid strike failure on compatible Whirlpool and Maytag washers. Even though the lid appears to close, if the strike has cracked or worn down it may not physically engage the lock or activate the switch correctly. Visually inspect the strike on the underside of the lid — if it's broken, missing, or chipped, replacement is straightforward. If the strike looks intact and the washer still won't start, the lid lock assembly itself or the wiring harness may need attention. Do I really not need any tools to install this? Correct — the W11457841 lid strike uses a twist-in design with no screws or hardware. To remove the old strike, rotate it counterclockwise until the internal retaining tab breaks free, then pull it out. To install the new one, push it into the mounting hole and twist clockwise until it clicks into place. The whole replacement typically takes under 5 minutes once you have the new part in hand. Work gloves are recommended to protect your hands while gripping the small plastic part, but no other tools are needed. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It is the exact same lid strike installed in compatible Whirlpool, Maytag, and Kenmore HE top-load washers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO W10915651 Microwave Waveguide Cover The XPARTCO W10915651 is an aftermarket replacement microwave waveguide cover compatible with select Whirlpool, KitchenAid, Jenn-Air, Maytag, Amana, Kenmore, Roper, Admiral, Magic Chef, Norge, Estate, and Ikea over-the-range and built-in microwave/oven combo models. The waveguide cover is a flat mica plate mounted on the interior right wall of the microwave cavity. It protects the waveguide — the channel through which microwave energy is directed into the cooking cavity — from food splatter, grease, and moisture. Without the cover, food particles can reach the waveguide and cause arcing, sparking, burning, and permanent damage to the magnetron or waveguide assembly. Made from mica (a heat-resistant mineral material), this cover measures approximately 5-3/8" L x 1-3/4" W and clips or slides into the mounting slot on the interior wall of the microwave. It directly replaces W10687366, W10120230, WPW10120230, and 461967451001. Replacing a damaged or burned waveguide cover promptly is the single most important step in preventing more expensive microwave damage. Installs in under 5 minutes with no tools. Quick Answer The XPARTCO W10915651 Microwave Waveguide Cover fixes microwaves that are sparking, arcing, burning smells, or have a scorched or missing cover on the interior right wall. Mica plate, approx. 5-3/8" L x 1-3/4" W. — installs in under 5 minutes. Compatible with Whirlpool, KitchenAid, Jenn-Air, Maytag, Amana, Kenmore, and more. Replaces W10687366, W10120230, WPW10120230, and 461967451001. Common Problems This Part Fixes Sparking or arcing inside the microwave during operation Burning smell coming from the microwave while in use Visible scorch marks, burn spots, or a hole in the existing waveguide cover Microwave stopping mid-cycle due to arcing or sparking Waveguide cover is cracked, warped, or missing entirely Uneven heating or microwave not heating food properly Microwave making popping or crackling sounds during operation Replaces Part Numbers This waveguide cover directly replaces the following OEM and cross-reference part numbers: W10915651, W10120230, WPW10120230, W10687366, 461967451001, AWP42398, PD00039892, EAP11769950, AP6038160, PS11769950.  If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This waveguide cover is compatible with select over-the-range and built-in microwave/oven combo models from the following brands: Whirlpool microwaves and microwave/oven combos (WOC, WOCA, WOEC series and more) KitchenAid microwaves and built-in combos Jenn-Air microwaves and built-in combos Maytag microwaves Amana microwaves Kenmore / Sears microwaves (Whirlpool-built models) Roper microwaves Admiral microwaves Magic Chef microwaves Norge microwaves Estate microwaves Ikea microwaves (select models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Protects the waveguide from food splatter and moisture — prevents arcing, sparking, and magnetron damage Made from mica — a heat-resistant mineral material rated for continuous high-temperature microwave exposure Dimensions: approximately 5-3/8" L x 1-3/4" W — fits the mounting slot on the interior right wall of compatible models Clips or slides into the existing mounting slot — no tools required, installs in under 5 minutes Replaces W10687366, W10120230, WPW10120230, and 461967451001 Compatible with Whirlpool, KitchenAid, Jenn-Air, Maytag, Amana, Kenmore, and more Replacing a burned or damaged cover immediately prevents far more expensive repairs to the magnetron or waveguide assembly Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number W10915651 Part Type Microwave Waveguide Cover (Mica Plate) Condition Aftermarket Replacement Material Mica (heat-resistant mineral) Dimensions Approximately 5-3/8" L x 1-3/4" W Location Interior right wall of the microwave cavity Installation Clips or slides into mounting slot — no tools required Compatible Brands Whirlpool, KitchenAid, Jenn-Air, Maytag, Amana, Kenmore, Roper, Admiral, Magic Chef, Norge, Estate, Ikea Installation Notes ⚠️ Unplug Microwave Before Starting Unplug the microwave before beginning. Open the microwave door and locate the waveguide cover on the interior right wall of the cavity — it is a flat rectangular plate, typically tan or off-white in color. If the old cover is burned, it may be stuck to the wall or disintegrating — carefully remove any remaining pieces and wipe the mounting area clean. Slide or clip the new W10915651 cover into the mounting slot on the right wall of the cavity — it should seat flat against the wall with no gaps. Ensure the cover is fully seated before use. Do not operate the microwave with a missing, cracked, or burned waveguide cover — even a small burn hole can cause arcing and progressive damage. Restore power and run a brief test cycle to confirm normal operation. Tools needed: None. A damp cloth may be needed to clean the mounting area. Frequently Asked Questions What does the waveguide cover do and why does it need to be replaced? The waveguide cover is a thin mica plate that covers the opening of the waveguide — the channel through which microwave energy travels from the magnetron into the cooking cavity. Its job is to prevent food particles, grease, and steam from entering and contaminating the waveguide. When food splatter builds up on the cover and burns, the cover develops scorch marks or burn-through holes. These damaged spots absorb microwave energy and cause arcing — sparks and electrical discharges that can quickly damage the magnetron, which is the most expensive component in the microwave. Replacing the waveguide cover promptly when it shows damage is the least expensive and most important preventive maintenance you can do for a microwave. Can I use the microwave without the waveguide cover? No — never operate a microwave with a missing, cracked, or burned waveguide cover. Without the cover, food particles and moisture can enter the waveguide directly, causing immediate arcing and sparking. Even a small hole in the cover can cause arcing. Operating the microwave in this condition risks damaging the magnetron (a $100–$200 or more repair), burning the waveguide channel, or creating a fire hazard. The waveguide cover is inexpensive and installs in minutes — always replace it before using the microwave again. My microwave is sparking — will replacing the waveguide cover fix it? Sparking is almost always caused by a burned or damaged waveguide cover, and replacing the cover resolves the sparking in the vast majority of cases. However, if the waveguide itself (the metal channel behind the cover) has been damaged from prolonged arcing, or if metal debris from a burned cover has entered the waveguide, additional cleaning or component repair may be needed. Inspect the area behind the old cover after removing it — if the wall or channel shows deep burn damage, contact our support team or a technician before operating the microwave again. How do I prevent the waveguide cover from burning again? The most effective prevention is to keep the interior of the microwave clean — specifically the waveguide cover itself and the walls near it. Wipe down the cover and interior walls with a damp cloth after each use, especially after heating anything that splashes or spatters. Use a microwave-safe cover or lid over food when heating. Never operate the microwave when empty, as this directs all microwave energy at the waveguide cover without any food to absorb it. With regular cleaning, a mica waveguide cover can last for years without needing replacement. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured from heat-resistant mica to match the dimensions and fit of the original W10915651 waveguide cover. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO W10205415 Dryer Drum Belt Replaces WPW10205415 The XPARTCO W10205415 Dryer Drum Belt is a high-quality aftermarket replacement designed to restore proper drum rotation in compatible dryers. The belt wraps around the dryer drum, connects with the motor pulley and idler pulley, and allows the drum to tumble clothes during the drying cycle. Manufactured with durable reinforced rubber, this 5-rib, 4-groove belt is built to withstand heat, tension, and everyday dryer use. It measures approximately 92 inches long and 3/8 inch wide, making it a direct replacement for W10205415 and WPW10205415. Quick Answer The XPARTCO W10205415 Dryer Drum Belt fixes dryers where the drum is not spinning, clothes are not tumbling, or the dryer runs but does not dry properly. It fits select Whirlpool, Maytag, Amana, Samsung, Kenmore, KitchenAid, Inglis, Crosley, and Caloric dryers. Common Problems This Part Fixes Dryer drum not spinning while the motor runs Clothes not tumbling during the drying cycle Dryer runs but clothes remain wet Squealing, thumping, or slapping noise during operation Broken, loose, stretched, or worn dryer belt Visible belt pieces inside the dryer cabinet Replaces Part Numbers This dryer drum belt replaces the following OEM and cross-reference part numbers: W10205415, WPW10205415, 35001137, 6602-001314, 1937372, AWP49503, PD00003618, AP5178009, PS3494357. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drum belt is compatible with select dryers from the following brands: Whirlpool dryers Maytag dryers Amana dryers Samsung dryers Kenmore / Sears dryers KitchenAid dryers Inglis dryers Crosley dryers Caloric dryers ⚠️ This compatibility list includes many supported models but may not be complete. Always verify your appliance model number before ordering. If you're unsure, our support team is ready to help confirm fitment. Model Cross Reference Use the Model Cross Reference section on this product page to search your appliance model number and confirm fitment. Exact model matches will show a ✓ Guaranteed Fit badge. When Should You Replace This Belt? Drum stops spinning but motor still runs You hear a snapping sound during operation Belt appears cracked, frayed, or stretched Dryer suddenly stops tumbling mid-cycle Clothes come out wet due to lack of tumbling Key Features Restores proper dryer drum rotation and tumbling 92 inch length x 3/8 inch width 5-rib, 4-groove design for secure grip Durable reinforced rubber construction Direct replacement for W10205415 and WPW10205415 Compatible with select gas and electric dryers Aftermarket replacement built to OEM-equivalent standards Product Specifications Part Number W10205415 Replaces WPW10205415 Part Type Dryer Drum Drive Belt Condition Aftermarket Replacement Application Gas and Electric Dryers Length 92 inches Width 3/8 inch Ribs 5 ribs, 4 grooves Material Reinforced rubber Color Black Compatible Brands Whirlpool, Maytag, Amana, Samsung, Kenmore, KitchenAid, Inglis, Crosley, Caloric Installation Notes ⚠️ Safety First — Disconnect Power Before Servicing Unplug the dryer from the power source before starting the repair. For gas dryers, shut off the gas supply. Remove the top and front panels to access the drum. Remove the old belt and install the new W10205415 belt around the drum with the ribbed side facing inward. Route the belt around the idler pulley and motor pulley, then reassemble the dryer and run a test cycle. Frequently Asked Questions Is W10205415 the same as WPW10205415? Yes. WPW10205415 is the updated OEM part number that replaces W10205415. This aftermarket belt is compatible with both part numbers. How do I know if my dryer belt is broken? A common sign is that the dryer motor runs, but the drum does not spin. You may also hear a thumping or slapping sound if the belt is loose, frayed, or partially broken. Will this belt fit my Kenmore dryer? Many Kenmore dryers are manufactured by Whirlpool and may use this belt. Use the Model Cross Reference search section to verify your exact model before ordering. Is this an OEM part? This is a high-quality aftermarket replacement part built to match OEM-equivalent dimensions and performance standards. It is not a genuine Whirlpool OEM part. Shop With Confidence Parts-O-Matic is a U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock parts for major appliance brands and ship quickly from our U.S. warehouse. Our team is available to help you verify compatibility before you buy. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less