Appliance Parts

XPARTCO DG94-00520A Oven Igniter The XPARTCO DG94-00520A is an aftermarket replacement oven burner igniter compatible with select Samsung gas ranges and ovens. The igniter is a hot surface igniter that draws electrical current through the oven safety valve to open it, then heats to ignition temperature to light the gas burner. When the igniter weakens or fails, the oven will not heat, will take too long to preheat, or will emit a gas smell without lighting. This complete assembly includes the igniter with bracket and lead/plug. It features 8-inch leads with female pins, draws 3.4–3.6 amps, and can be used as either a bake or broil igniter depending on the model. The bracket measures 3-3/4" L x 1-3/4" W x 13/16" H and the harness and plug extend 7-7/8" from the igniter body. Verify that the electrical plug matches your existing igniter before ordering. Installs in 20–30 minutes with basic hand tools. Quick Answer The XPARTCO DG94-00520A Oven Igniter fixes Samsung gas ovens that won't heat, take too long to preheat, or have an igniter that glows but never lights the burner. Draws 3.4–3.6A. Includes bracket and lead/plug with 8" leads. Can be used as bake or broil igniter depending on model. Always verify plug type matches before ordering. Common Problems This Part Fixes Oven not heating at all — gas is not igniting Oven takes excessively long to preheat (weak igniter not reaching ignition temperature) Igniter glows orange or red but never lights the gas burner Smell of gas when oven is turned on but burner does not light Oven heats inconsistently or shuts off mid-cycle Broiler not lighting on applicable models Clicking sounds from the oven without ignition Replaces Part Numbers This oven igniter directly replaces the following OEM and cross-reference part numbers: DG94-00520A, 2692271, EAP4241428, ASM38124, PD00027453, AP5577941, PS4241428. Always verify the electrical plug type matches your existing igniter before ordering. Contact our support team if you're unsure. Compatibility This igniter is compatible with select gas ranges and ovens from the following brands: Samsung gas ranges (freestanding and slide-in) Important: Some Samsung models use two igniters — one for bake and one for broil. This part can serve as either depending on your model. Verify which igniter position you are replacing and confirm the plug type matches before ordering. Key Features Hot surface igniter — draws current through the oven safety valve to open it, then ignites the gas burner Draws 3.4–3.6 amps — correct amperage range to open the Samsung gas valve and reach ignition temperature Can be used as bake or broil igniter depending on the model Complete assembly — includes igniter, bracket, and lead/plug with 8" leads and female pins Bracket dimensions: 3-3/4" L x 1-3/4" W x 13/16" H; block measures 1-1/2" L Harness and plug extend 7-7/8" from the igniter body Metal, ceramic, and plastic construction — built to withstand high oven temperatures Aftermarket replacement built to OEM-equivalent quality standards DIY-friendly repair — installs in 20–30 minutes with basic hand tools Product Specifications Part Number DG94-00520A Part Type Oven Burner Igniter (Hot Surface Igniter) Condition Aftermarket Replacement Application Gas Ranges and Ovens (Bake or Broil) Amperage Draw 3.4 – 3.6 Amps Bracket Dimensions 3-3/4" L x 1-3/4" W x 13/16" H Block Length 1-1/2 inches Lead Length 8 inches (female pins) Harness / Plug Reach 7-7/8 inches from igniter body Material Metal / Ceramic / Plastic Includes Igniter, bracket, and lead/plug assembly Compatible Brands Samsung Installation Notes ⚠️ Shut Off Gas and Unplug Before Starting Shut off the gas supply at the shutoff valve and unplug the range from the power outlet before beginning any repair. Open the oven door and remove the oven racks. Remove the oven bottom panel by unscrewing the retaining screws, then lift and remove the heat shield beneath it to expose the burner assembly. Unscrew the igniter from the burner bracket — typically one or two screws. Carefully disconnect the wiring harness connector. Connect the new DG94-00520A igniter to the wiring harness, secure it to the burner bracket with the screws, then reinstall the heat shield and bottom panel. Restore gas supply and power, then run a test cycle to verify the oven lights properly. Note: Do not touch the ceramic igniter element with bare hands — oils from skin can reduce its lifespan. Tools needed: Phillips screwdriver, nut driver, work gloves. Frequently Asked Questions How do I know if my oven igniter is bad? The most common signs are the oven not heating at all, taking much longer than usual to preheat, or the igniter glowing orange or red but never lighting the burner. A healthy igniter glows bright orange and ignites the gas within 30–90 seconds. If it glows dimly or stays on without lighting the burner, it is drawing insufficient current to open the gas safety valve and needs to be replaced. Why does my oven igniter glow but the oven still doesn't heat? A glowing igniter that never lights the burner is the classic sign of a weak igniter. The igniter must draw enough current — typically 3.2 amps or more — to open the gas safety valve. As igniters age, their resistance increases and amperage draw drops below the threshold needed to open the valve. The igniter glows because it still has some current, but not enough to let gas through. Does my Samsung oven use one igniter or two? Many Samsung gas ranges have two igniters — one for the bake burner (bottom of oven) and one for the broil burner (top of oven). The DG94-00520A can serve as either depending on the model. Check which position is failing before ordering, and verify that the plug type on this igniter matches your existing part. Do I need to verify the plug type before ordering? Yes — this is important. Some Samsung models use a plug that is a direct match for this igniter, while others may require cutting the old plug and using wire nuts or crimp connectors. Inspect the connector on your existing igniter and compare it to the 8" female pin connector included with this part before ordering. Contact our support team if you need help confirming compatibility. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured from metal, ceramic, and plastic to match the dimensions and electrical specifications of the original DG94-00520A igniter. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

57291  Refrigerator Icemaker Water Line (5 Feet) 5 Feet Stainless Steel Braided

Read more less

XPARTCO 131763256 Washer Door Lock Assembly Replaces WH10X27534 The XPARTCO 131763256 is an aftermarket replacement door lock and switch assembly compatible with a wide range of Frigidaire, Electrolux, GE, White-Westinghouse, Tappan, Kenmore, Crosley, and Gibson front-load washers. The door lock latch and switch assembly is mounted on the front panel of the washer just inside the door opening — when the door closes, the door strike enters the lock and engages the latching mechanism, locking the door for the duration of the cycle and signaling the control board that it's safe to fill, agitate, and spin. Without a functioning door lock, the washer will not start, will not lock the door, may stop mid-cycle, or may display fault codes like E47. This is a universal-fit aftermarket assembly that spans both the Frigidaire platform (131763xxx-series part numbers) and the GE platform (WH10X-series part numbers) — one physical part covers both manufacturers' cross-referenced door lock positions on compatible front-load washers. Rated 120VAC, 50/60Hz, with 8 terminals. Dimensions: 4-1/2"L x 3-7/8"W x 1-1/2"H. Gray and red matte finish, plastic and metal construction. It directly replaces 131763256, 131763202, 131763255, 131763200, 131763245, 1317632, 1312694, 131269400, 137523400, 1531974, 3626240, 4547033, 4547432, 5301317632, 08003223, K001317632, K1317630-K938, K1317632, LP3202, PA66-GF25, WH10X27534, WH10X10003, WH10X10007, WH10X27194, AH2367737, AH3418879, AP4455026, AP4694680, AP6285657, AP6327625, EA3418879, EAP2367737, PD00038657, PD00070219, PS2367737, PS3418879, PS12343346, and PS12364048. Often replaced together with the matching door strike (131763310, sold separately). Installs in 15–20 minutes with basic hand tools. Quick Answer The XPARTCO 131763256 Washer Door Lock Assembly fixes Frigidaire, Electrolux, GE, Kenmore, Crosley, White-Westinghouse, Tappan, and Gibson front-load washers that won't start, won't lock the door, won't spin, won't drain, won't fill, stop mid-cycle, or display E47 error codes. Universal-fit assembly — spans both Frigidaire (131763xxx) and GE (WH10X) platforms. 120VAC, 50/60Hz, 8 terminals. 4-1/2"L x 3-7/8"W x 1-1/2"H. Gray/red matte. Replaces 131763202, 131763255, 131763200, 131763245, 1317632, 131269400, 4547033, WH10X27534, WH10X10003, WH10X10007, WH10X27194, AP6285657, AP4455026, PS2367737, and 20+ more cross-references. Often paired with the door strike (131763310, sold separately). Common Problems This Part Fixes Washer won't start — control board not detecting a locked door Door won't lock at the start of the cycle Washer stops mid-cycle due to a door lock fault E47 error code displayed on the control panel Washer pumps but won't spin — spin cycle blocked by unlocked-door detection Washer won't drain — drain cycle blocked by door-lock signal loss Washer won't fill with water — fill cycle blocked by door-lock signal Door lock assembly visibly broken, cracked, or missing latch teeth Door won't unlock at the end of the cycle — stuck lock mechanism Unusual noise from the door lock area during cycle transitions Replaces Part Numbers This universal-fit door lock assembly directly replaces the following OEM and cross-reference part numbers across multiple brands: 131763256, 131763255, 131763202, 1312694, 131269400, 131763200, 131763245, 3626240, 4547033, PA66-GF25, LP3202, AFR14205, AP6285657, EAP2367737, PD00038657, PS12364048, WH10X27534, WH10X10003, 08003223, 4547432, 5301317632, K001317632, K1317630-K938, K1317632, WH10X10007, WH10X27194, AP6327625, AGE754798, PS12343346, PD00070219, PD00070219. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This universal-fit door lock assembly is compatible with select front-load washers from the following brands: Frigidaire front-load washers — Affinity series, FAFS/FAFW/FFFS/FFFW/FRFW/FTF/FTR/FWFB/FWT/GLTF/GLEH series and many related models Electrolux front-load washers — select models with the matching door lock configuration GE front-load washers — WCCH404, WPXH214, WSSH300, WSXH208 series and related models (WH10X27534 cross-reference) White-Westinghouse front-load washers — select models Tappan front-load washers — select models Kenmore / Sears front-load washers — select Frigidaire-built and GE-built models Crosley front-load washers — BTF1240ES0, BTF1240ES1, BTF1240FS0 and related models Gibson front-load washers — select models Note: The door lock assembly (131763256) and the door strike (131763310) are two separate components that work together — if both are worn, replacing them together as a matched set ensures reliable door locking and prevents premature wear on the new lock. The strike is what physically enters the lock when the door closes. Always verify your model number before ordering. Key Features Universal-fit door lock and switch assembly — replaces both Frigidaire (131763xxx-series) and GE (WH10X-series) OEM door locks in a single aftermarket part Locks the washer door during the wash and spin cycles and signals the control board that the door is safely closed Resolves E47 error codes on compatible Frigidaire and Electrolux washers Rated 120VAC, 50/60Hz — correct electrical specifications for compatible washers 8 terminal connections for the wire harness Dimensions: 4-1/2"L x 3-7/8"W x 1-1/2"H Gray and red matte finish, plastic and metal construction Replaces 35+ OEM and cross-reference part numbers spanning Frigidaire, GE, Electrolux, and universal aftermarket catalogs Often replaced together with the matching door strike (131763310, sold separately) as a paired repair Compatible with Frigidaire, Electrolux, GE, White-Westinghouse, Tappan, Kenmore, Crosley, and Gibson front-load washers Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in 15–20 minutes with basic hand tools Product Specifications Part Number 131763256 Also Replaces (GE-side) WH10X27534 Part Type Washer Door Lock and Switch Assembly (Universal Fit) Condition Aftermarket Replacement Application Front-Load Washers (Frigidaire and GE platforms) Voltage 120V AC Frequency 50/60 Hz Terminals 8 Dimensions 4-1/2"L x 3-7/8"W x 1-1/2"H Color Gray / Red Finish Matte Material Plastic / Metal Error Codes Resolved E47 (door lock error) Often Paired With Door Strike (131763310, sold separately) Compatible Brands Frigidaire, Electrolux, GE, White-Westinghouse, Tappan, Kenmore, Crosley, Gibson Installation Notes ⚠️ Unplug Washer Before Starting — Wear Work Gloves Disconnect power before beginning. Wear work gloves to protect your hands. The door lock assembly is mounted on the front panel of the washer just inside the door opening. Open the washer door (if the door is stuck locked, use a putty knife to release the manual override latch through the bottom service opening, then open the door). Peel back the rubber door boot from the front panel edge to expose the mounting screws for the lock assembly — on some models this requires removing the spring-loaded wire clamp securing the boot with needle-nose pliers. Photograph the wire harness connections before disconnecting anything — this assembly has 8 terminals, so getting the wire mapping correct on reinstallation is important. Remove the 2 mounting screws holding the lock assembly to the front panel. Reach in and pull the assembly out through the door opening. Disconnect the wire harness plug from the old assembly. Snap the new 131763256 assembly onto the wire harness plug (should click firmly into place), position it in the front panel opening, and secure with the 2 mounting screws. Press the rubber door boot back into the groove at the front panel and reinstall the spring-loaded wire clamp if applicable — this is the trickiest part of the install. Restore power and test by closing the door and starting a cycle to confirm the door locks and the washer runs normally. Tools needed: Phillips screwdriver, needle-nose pliers, putty knife (for stuck doors), work gloves. Frequently Asked Questions Does this really fit both Frigidaire AND GE washers? Yes — this is one of those cases in front-load washer parts where an aftermarket door lock assembly has been designed to serve as a direct replacement for both the Frigidaire 131763xxx-series and the GE WH10X-series door locks. The two OEM assemblies share the same physical dimensions, 8-terminal wire harness configuration, and mounting geometry, allowing a single aftermarket part to function correctly in both platforms. Compatible models span Frigidaire's Affinity series, GE's WCCH/WPXH/WSSH/WSXH series, and select Electrolux, Kenmore, Crosley, White-Westinghouse, Tappan, and Gibson front-load washers. Always verify your specific model number before ordering. What does error code E47 mean on my Frigidaire washer? E47 on Frigidaire and Electrolux front-load washers indicates a door lock circuit fault — the control board is not receiving the expected signal from the door lock assembly to confirm the door is closed and locked. This is typically caused by a failed door lock assembly, but can also be caused by a broken door strike (which physically enters the lock), a damaged wire harness, or a control board issue. Replacing the 131763256 door lock resolves E47 when the lock is the cause; if the code returns after replacement, check the strike and the wire harness next. My washer won't drain and won't spin — is the door lock the problem? Possibly, yes. Front-load washers block drain and spin operations whenever the control board can't confirm the door is locked — this is a safety measure to prevent water release and drum spinning while the door might be open. If your washer fills but won't advance to drain and spin, and there are no obvious pump or motor problems, a failed door lock is a common cause even though the symptom doesn't directly say "door." The failure can also manifest as "won't fill" or "unusual noise" during cycle transitions. Testing the door lock with a multimeter (or replacing it as a diagnostic step given the low cost) is a good first move for these symptoms. My washer door is stuck closed — how do I get it open to install this? If the door is stuck in the locked position because of a failed door lock, you can use a putty knife or thin flat tool to manually release the lock through the bottom service opening at the front of the washer. Reach in through the access panel at the lower front and locate the manual release lever or latch on the back of the door lock assembly — gently push or pry it to release the mechanism. The door should then open. Once open, you can proceed with the installation. Always disconnect power from the washer first. Do I need to replace the door strike (131763310) too? Not always, but often. The door strike is the matching component mounted on the washer door itself — it's the part that the lock's latching mechanism grips when the door closes. If the strike is worn, cracked, or its plastic teeth are broken, the new lock won't engage reliably even if it's working perfectly. Inspect the strike on the door for visible damage before ordering just the lock. Many repair scenarios call for replacing both at the same time since both wear together and the parts complement each other. The matching strike is part number 131763310 (sold separately). Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Frigidaire, GE, or Electrolux OEM part, but is manufactured from plastic and metal to match the dimensions (4-1/2"L x 3-7/8"W x 1-1/2"H), electrical specifications (120V AC, 50/60Hz), 8-terminal wire harness configuration, and lock engagement function of the original door lock assemblies it replaces across multiple manufacturers' catalogs. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO DC61-01215B Dryer Idler Tension Spring – Compatible with Samsung & Kenmore Dryers Product Description Restore proper belt tension and smooth drum rotation with the XPARTCO DC61-01215B Dryer Idler Tension Spring. This high-quality replacement spring maintains correct tension on the idler pulley, ensuring the dryer belt stays tight during operation. A worn or broken tension spring can cause belt slippage, squealing noises, drum not turning, or dryer stopping mid-cycle. Replacing it with this durable XPARTCO spring helps maintain reliable dryer performance. Replaces Part Numbers DC61-01215B, 2069087, DC61-01215A, DE1215B, PD00027514, EAP4206154, AP4211487, PS4206154. Compatibility This replacement idler tension spring fits select Samsung and Kenmore (Samsung-manufactured) dryers. Example compatible models include (but are not limited to):Samsung DV42H5000EW, DV45H7000EWKenmore 592-89045, 592-89047 Always verify your dryer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM tension and fit specifications 🔧 Maintains Proper Belt Tension – Keeps dryer belt tight and aligned 🔇 Reduces Noise & Slippage – Prevents squealing and belt skipping 💪 Durable Spring Steel Construction – Built for long-lasting elasticity 🛡️ Fixes Common Issues – Solves drum not turning, belt slipping, or abnormal noises 📐 Product Specification Part Number: DC61-01215B Component Type: Dryer Idler / Belt Tension Spring Material: High-tensile spring steel Application: Idler pulley tension control Mounting: Hooks between idler arm and cabinet Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, needle-nose pliers ⚠️ Safety First: Always unplug the dryer before servicing to prevent electrical shock. Steps: Disconnect power and open the dryer cabinet. Locate the idler pulley and tension spring. Remove the worn or broken spring. Install the new XPARTCO DC61-01215B spring in the same mounting points. Reassemble dryer panels and restore power. Run a test cycle to confirm proper belt tension. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Restore proper belt tension and smooth dryer operation — Add to Cart Now for a dependable, budget-friendly repair!

Read more less