Appliance Parts

XPARTCO 675813 Dishwasher Thermal Fuse The XPARTCO 675813 is an aftermarket replacement bimetal thermal fuse (TCO — thermal cut-off) kit compatible with a wide range of Whirlpool-family dishwashers including Whirlpool, Kenmore, KitchenAid, Maytag, Estate, Crosley, Inglis, Roper, and Admiral. The thermal fuse is a one-time safety device located on or near the control board that monitors internal temperature. If the dishwasher overheats — due to a blocked vent, malfunctioning heating element, or other fault — the fuse permanently interrupts power to protect the dishwasher and prevent fire hazards. Unlike a resettable thermostat, a blown thermal fuse must be replaced. Once it trips, the dishwasher will show no power and will not start. The kit includes one thermal cutoff fuse with a 2-wire harness (leads extending approximately 18 inches from the fuse), one zip tie, and installation instructions. The fuse body measures 1-1/16" L x 1" W x 7/16" H. The new wiring harness must always be used when replacing the fuse. Installs in 5–15 minutes with basic hand tools. Quick Answer The XPARTCO 675813 Dishwasher Thermal Fuse Kit fixes Whirlpool-family dishwashers that show no power, won't start, have a blank control panel, or stopped mid-cycle with no response. The thermal fuse permanently trips when the dishwasher overheats and must be replaced. Kit includes fuse with 2-wire harness, zip tie, and instructions. Fuse body 1-1/16" L x 1" W x 7/16" H. Always install using the new harness included. Compatible with Whirlpool, Kenmore, KitchenAid, Maytag, and more. Common Problems This Part Fixes Dishwasher completely dead — no power, no lights, no response when buttons are pressed Control panel blank with no indicator lights or display Dishwasher stopped mid-cycle and will not restart Dishwasher will not start despite the door being closed and latched No sounds when attempting to start the dishwasher Dishwasher behaves as if it has no power even though the outlet is live Replaces Part Numbers This dishwasher thermal fuse kit directly replaces the following OEM and cross-reference part numbers: 675813, 3375557, 3376359, 675813VP, 679723, AH382828, OEM9345567, AWP39651 PD00002439, EA382828, EAP382828, AP3115186, PS382828. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This thermal fuse kit is compatible with select dishwashers from the following brands: Whirlpool dishwashers Kenmore / Sears dishwashers (Whirlpool-built models) KitchenAid dishwashers Maytag dishwashers Estate dishwashers Crosley dishwashers Inglis dishwashers Roper dishwashers Admiral dishwashers Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Bimetal thermal cut-off (TCO) fuse — permanently interrupts power if the dishwasher overheats, protecting against fire hazard One-time safety device — once tripped, the fuse must be replaced (it does not reset) Rated at 98°C — trips when internal temperature exceeds the safe operating limit Fuse body dimensions: 1-1/16" L x 1" W x 7/16" H; leads extend approximately 18" from fuse Kit includes thermal fuse with 2-wire harness, zip tie, and installation instructions Always install using the new harness included — never reuse the old harness Metal and plastic construction — reliable performance and heat resistance Direct replacement for 675813, 675813VP, 3375557, and 3376359 — no modification required Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in 5–15 minutes with basic hand tools Product Specifications Part Number 675813 Part Type Dishwasher Thermal Fuse / Thermal Cut-Off (TCO) Kit Condition Aftermarket Replacement Fuse Type Bimetal thermal cut-off (one-time, non-resettable) Trip Temperature 98°C (208°F) Fuse Body Dimensions 1-1/16" L x 1" W x 7/16" H Lead Length Approximately 18 inches from fuse body Color White / Brown Material Metal / Plastic Kit Includes Thermal cutoff fuse with 2-wire harness, zip tie, instructions Compatible Brands Whirlpool, Kenmore, KitchenAid, Maytag, Estate, Crosley, Inglis, Roper, Admiral Installation Notes ⚠️ Unplug or Switch Off Breaker Before Starting Unplug the dishwasher or turn off the circuit breaker before beginning any repair. The thermal fuse is located inside the dishwasher door panel near the control board. Open the dishwasher door and remove all screws from the inner door panel — a Torx bit is typically required on Whirlpool-family models. Carefully lift the inner door panel to expose the control board housing. Remove the black plastic cover over the control board to access the thermal fuse — it is typically on the right side of the board with one wire connected to each terminal. Test the old fuse with a multimeter for continuity (no continuity confirms the fuse has blown). Disconnect the old fuse and its harness. Connect the new 675813 fuse using the new 2-wire harness included in the kit — do not reuse the old harness. Secure the harness with the included zip tie. Reinstall the control board cover, inner door panel, and all screws. Restore power and run a test cycle. Note: If the fuse blows again after replacement, an underlying cause such as a blocked vent, failed heating element, or faulty control board should be diagnosed before replacing the fuse a second time. Tools needed: Torx screwdriver (T15 or T20), Phillips screwdriver, multimeter, work gloves. Frequently Asked Questions What does the dishwasher thermal fuse do? The thermal fuse is a one-time safety device that monitors the internal temperature of the dishwasher. If the temperature rises above the safe operating limit — 98°C in this case — the fuse permanently interrupts the electrical circuit, cutting all power to the dishwasher. This protects both the appliance and your home from fire hazard caused by overheating. Unlike a resettable thermostat, a blown thermal fuse cannot be reset and must be physically replaced. How do I know if my thermal fuse has blown? The most obvious sign is a completely dead dishwasher — no lights, no sounds, and no response when you press any buttons, even though the outlet has power. You can confirm a blown fuse with a multimeter: disconnect the fuse from the harness and test for continuity across its two terminals. A working fuse will show continuity (near-zero resistance); a blown fuse will show no continuity (open circuit). If the fuse tests bad, replace it with the 675813 kit. Why did my thermal fuse blow, and will it happen again? Thermal fuses blow when the dishwasher overheats. Common causes include a blocked air vent, a malfunctioning or shorted heating element, a failed thermostat, or an electrical fault in the control board. If you simply replace the fuse without addressing the root cause, it may blow again. After replacing the fuse, run the dishwasher and monitor for any unusual heat, steam, or burning smell. If the fuse blows again, have the underlying fault diagnosed before ordering another replacement. Why must I use the new harness and not the old one? When a thermal fuse blows, the wiring harness connected to it may have been exposed to the same overheating event that tripped the fuse. The wires or connectors may have degraded or partially melted even if they appear intact. Using the old harness risks a poor connection or a recurring fault. Always install the new 2-wire harness included in the kit to ensure a reliable, safe connection. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured from metal and plastic to match the dimensions, trip temperature, and performance of the original 675813 thermal fuse. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

XPARTCO DC64-00828B Dryer Door Switch The XPARTCO DC64-00828B is an aftermarket replacement dryer door switch (also called a door jamb switch) compatible with a wide range of Samsung and Kenmore Samsung-built electric and gas dryers — including the DV2, DV3, DV4, DV5, DVE, DVG, 592, 401, and 402 series. The door switch is a small safety component mounted near the dryer door frame that detects whether the door is closed. When the door closes, the switch is activated, signaling the control board that the dryer is safe to start or continue running. If the switch fails to detect the closed door, the dryer will not start, will stop mid-cycle, or in rare unsafe failure modes, may continue running with the door open. This switch directly replaces DC64-00828A (the prior version), 2071595, AP4578931, EAP4210965, PS4210965, PS4210964, 2071594, and PD00028436. It is constructed from durable plastic and metal in white, with dimensions of approximately 1.73"L x 1.73"W x 0.47"H. Note: while this switch looks easy to remove, the front panel actually needs to come off to access it cleanly. Installs in 20–30 minutes with basic hand tools. Quick Answer The XPARTCO DC64-00828B Dryer Door Switch fixes Samsung and Kenmore Samsung-built dryers that won't start when the door is closed, stop mid-cycle, display error codes dC, dF, dE, or d0, or continue running with the door open. Approx. 1.73"L x 1.73"W x 0.47"H, white. Replaces DC64-00828A, 2071595, AP4578931, EAP4210965, PS4210965, PS4210964, 2071594, PD00028436. Compatible with Samsung DV2, DV3, DV4, DV5, DVE, DVG series and Kenmore 592/401/402-series dryers. Common Problems This Part Fixes Dryer not starting even though the door is closed Dryer stopping mid-cycle for no apparent reason — door switch losing signal intermittently Error codes dC, dF, dE, or d0 displayed on models with digital displays Dryer continuing to run with the door open (unsafe failure mode — replace immediately) Interior dryer light not turning on when the door is opened Door switch button visibly broken, stuck, or not making the expected click when pressed Multimeter test shows the switch fails to change state when actuated Replaces Part Numbers This door switch directly replaces the following OEM and cross-reference part numbers: DC64-00828B, DC64-00828A, 2071595, AP4578931, ASM68666, EAP4210965, PD00028436, PS4210965, WP35001125, 35001125, AP6008683, PS11741823 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This door switch is compatible with select Samsung and Kenmore Samsung-built electric and gas dryers, including: Samsung dryers — DV2 series (DV203AEW, DV203AGS, DV22K6800EW, DV2C6BEW, DV2C6BGW and related) Samsung dryers — DV3 series (DV306LEW, DV306LGW, DV316BEC, DV316BEW, DV316BGC, DV316BGW, DV316LES, DV316LEW, DV330AEB, DV330AEW, DV3C6BEW, DV3C6BGW, DV395ETPASU and related) Samsung dryers — DV4 series (DV400EWHDWR, DV400GWHDWR, DV42H5000GW, DV45H7000EW, DV48J7770GW and related) Samsung dryers — DV5 series (DV50K7500EW and related) Samsung dryers — DVE series (DVE60M9900W and related electric models) Samsung dryers — DVG series (DVG45N5300V and related gas models) Kenmore / Sears dryers — 592, 401, and 402 series (Samsung-built models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Safety switch that detects whether the dryer door is closed — required for the dryer to start and run Direct replacement for the original equipment door switch in compatible Samsung and Kenmore dryers Dimensions: approximately 1.73"L x 1.73"W x 0.47"H — matches original switch sizing Durable plastic housing with metal contacts — withstands frequent door open/close cycles Resolves Samsung door-related error codes including dC, dF, dE, and d0 Replaces DC64-00828A, 2071594, 2071595, AP4578931, EAP4210965, PS4210964, PS4210965, and PD00028436 Compatible with Samsung DV2, DV3, DV4, DV5, DVE, DVG series and Kenmore 592/401/402-series dryers Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 20–30 minutes with basic hand tools Product Specifications Part Number DC64-00828B Also Replaces DC64-00828A (prior version) Part Type Dryer Door Switch (Door Jamb Switch) Condition Aftermarket Replacement Application Electric and Gas Dryers (Samsung platform) Dimensions Approximately 1.73"L x 1.73"W x 0.47"H Color White Material Plastic / Metal Error Codes Resolved dC, dF, dE, d0 (door-related) Compatible Brands Samsung, Kenmore (Samsung-built) Installation Notes ⚠️ Unplug Dryer Before Starting — Wear Work Gloves Disconnect power and turn off the circuit breaker before beginning. Wear work gloves to protect your hands. Although the door switch appears easy to access from the front, on most Samsung dryer models the front panel actually needs to be removed to install the new switch cleanly. Unscrew and lift off the front panel — be careful not to drop it during reinstallation. Locate the old door switch mounted near the door frame opening. Photograph the wire connections before disconnecting. Unplug the wire harness from the old switch, release the retaining tabs or remove the mounting screws holding the switch in place, and pull it free. Install the new DC64-00828B switch in the same position, reconnect the wire harness, and reinstall the front panel. Restore power, then close the dryer door and start a cycle to confirm the door is properly detected and the dryer runs normally. Tools needed: Phillips screwdriver, work gloves. Frequently Asked Questions What do error codes dC, dF, dE, and d0 mean on Samsung dryers? These door-related error codes on Samsung dryers all indicate the control board is not receiving the expected "door closed" signal from the door switch. dC and d0 commonly appear when the dryer cannot detect a closed door at the start of a cycle, while dF and dE appear when the door signal is lost during a cycle. The dryer's safety logic prevents operation under any of these conditions. Replacing a failed DC64-00828B door switch resolves these codes when the switch itself is the cause; if the codes persist after replacement, check the wiring harness between the switch and the control board for damage. My dryer is running with the door open — what should I do? A dryer that continues to run with the door open is a serious safety concern and should be addressed immediately. This usually indicates a failed door switch that is stuck in the "closed" position electrically, even though the door is physically open. Disconnect power to the dryer right away and avoid running it until the switch has been replaced. The DC64-00828B replacement restores normal safety behavior. Until the repair is complete, do not run the dryer. What is the difference between DC64-00828B and DC64-00828A? These are the same door switch across successive production revisions. DC64-00828A was the original part number and DC64-00828B is the current updated version. Both are fully interchangeable — if your dryer's parts diagram shows DC64-00828A, the DC64-00828B is the correct current replacement and is covered by this listing. My dryer suddenly stops mid-cycle even though the door is closed — could this be the switch? Yes — a door switch with intermittent contact failure is a common cause of unexplained mid-cycle shutdowns on Samsung dryers. The switch may be working correctly when first activated but losing its signal momentarily during operation due to vibration or worn internal contacts, causing the control board to interpret a momentary "door open" condition and stop the cycle. If this is happening repeatedly without any other identifiable cause, replacing the DC64-00828B door switch is the recommended fix. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured from durable plastic and metal to match the dimensions, switch contacts, and function of the original DC64-00828B dryer door switch. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WH12X10334 Washer Lid Switch with Wire Harness The XPARTCO WH12X10334 is an aftermarket replacement washer lid switch assembly with wire harness compatible with select GE, Hotpoint, RCA, and Kenmore top-load washers — including the GTWN4250, GCWN4950, GTW180, GTWN2800, GTWN5550, GTUP270, and HSWP1000 series. The lid switch is a magnetic switch mounted near the lid hinge that detects whether the washer lid is open or closed. A magnet attached to the lid activates the switch when the lid closes — a small pin on the switch presses against an internal lever to signal the control board that it is safe to agitate or spin. This safety mechanism prevents the washer from running with the lid open. When the lid switch fails, the washer may not start, may fill with water but not proceed to the wash cycle, may stop mid-cycle, may not spin or agitate even with the lid closed, or may display lid-related error codes on models with digital displays. This assembly includes the switch and attached wire harness. It directly replaces WH12X10141, AP3968471, 1256927, AH1482372, EA1482372, and PS1482372. Installs in 20–30 minutes with basic hand tools. Quick Answer The XPARTCO WH12X10334 Washer Lid Switch fixes GE, Hotpoint, RCA, and Kenmore top-load washers that won't start, fill but don't proceed to wash, stop mid-cycle, or won't spin or agitate with the lid closed. Magnetic switch with wire harness — pin-and-lever design. Replaces WH12X10141, AP3968471, 1256927, AH1482372, EA1482372, PS1482372. Compatible with GE GTWN4250, GCWN4950, GTW180, GTWN2800, GTWN5550, GTUP270, and Hotpoint HSWP1000 series. Common Problems This Part Fixes Washer not starting — lid switch not signaling the lid is closed Washer filling with water but not proceeding to the wash cycle Washer stopping mid-cycle even though the lid is closed Washer not agitating or spinning despite the lid being closed Washer running intermittently — switch contact making and losing connection Lid-related error codes displayed on models with digital control panels Washer running with the lid open — switch stuck closed (less common but possible safety concern) Replaces Part Numbers This lid switch assembly directly replaces the following OEM and cross-reference part numbers: WH12X10334, 1256927, AGE26415, AH1482372, AP3968471, EA1482372, EAP1482372, PD00001112, PS1482372 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This lid switch assembly is compatible with select top-load washers from the following brands and series: GE top-load washers — GTWN4250D0WS, GTWN4250D1WS, GTWN4250M1WS series GE top-load washers — GCWN4950D2WS series GE top-load washers — GTW180SCJ0WW series GE top-load washers — GTWN2800D0WW series GE top-load washers — GTWN5550D0WW series GE top-load washers — GTUP270EM4WW series Hotpoint top-load washers — HSWP1000M4WW series RCA top-load washers (select GE-built models) Kenmore / Sears top-load washers (select GE-built models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Magnetic lid switch detects whether the washer lid is open or closed and signals the control board accordingly Pin-and-lever design — the lid's magnet activates the switch, which presses an internal pin against a lever to confirm the lid is closed Prevents the washer from agitating or spinning when the lid is open — important safety function Includes pre-attached wire harness for direct connection to the washer's wiring Replaces WH12X10141, AP3968471, 1256927, AH1482372, EA1482372, and PS1482372 Compatible with GE, Hotpoint, RCA, and Kenmore top-load washers Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 20–30 minutes with basic hand tools Product Specifications Part Number WH12X10334 Part Type Washer Lid Switch Assembly with Wire Harness Condition Aftermarket Replacement Application Top-Load Washers Switch Type Magnetic, pin-and-lever activation Includes Lid switch and attached wire harness Compatible Brands GE, Hotpoint, RCA, Kenmore Installation Notes ⚠️ Unplug Washer Before Starting — Wear Work Gloves Disconnect power before beginning. Wear work gloves to protect your hands. The lid switch is located near the lid hinge area at the top of the washer cabinet. Use a putty knife to release the spring clips along the front edge of the top panel (or console, depending on model), then lift the top panel to access the switch from underneath. Locate the lid switch — it is typically mounted near the hinge or under the console. Photograph the wire connections before disconnecting. Disconnect the wire harness connector, or if your model requires it, cut and splice the wires using wire strippers and crimpers. Remove the mounting screws (typically a 1/4" nut driver) and remove the old switch. Install the new WH12X10334 switch in the same position, secure the mounting screws, and reconnect or re-splice the wire harness. Reinstall the top panel by aligning and pressing down until the spring clips engage. Restore power and test by closing the lid and starting a cycle to confirm the washer agitates and spins normally. You can test the old switch's continuity with a multimeter before removal to confirm it has failed. Tools needed: Putty knife, 1/4" nut driver, wire strippers, crimpers. Frequently Asked Questions What does the washer lid switch do? The lid switch is a safety device that detects whether the washer lid is open or closed. A magnet attached to the underside of the lid activates the switch when the lid closes, which presses a small pin against an internal lever to send a signal to the control board confirming the lid is securely shut. The washer's control board uses this signal to allow agitation and spin — both of which are blocked whenever the lid is detected as open, as a safety measure to prevent injury from a spinning or moving basket. My washer fills with water but won't start the wash cycle — is it the lid switch? Yes — this is one of the most common lid switch failure symptoms. The washer is able to complete the fill phase because filling is typically not gated by the lid switch, but the agitation and spin phases require lid switch confirmation that the lid is closed. If the switch has failed and is not properly signaling lid closure, the washer fills normally but then stalls before agitating. According to repair technicians, when a washer fills and drains but does not agitate or spin, the lid switch is the first part that should be checked and is often the cause. How do I test if the lid switch has failed? Unplug the washer and access the switch as described in the installation notes. Disconnect the wire harness and set your multimeter to continuity or resistance mode. With the lid closed and the magnet engaging the switch pin, a working switch should show closed continuity. With the lid open (pin released), the switch should show open continuity. If the switch shows the same reading (either always open or always closed) regardless of lid position, the switch has failed and needs replacement. Could a bad lid switch cause water filling and draining issues too? In some specific cases, yes — some owners have reported resolving combinations of fill, drain, and spin issues by ultimately tracing the root cause back to a faulty lid switch, even after replacing other components like the water level pressure switch or control board. If you've already addressed other suspected causes for irregular cycle behavior and the symptoms persist, testing or replacing the lid switch is a low-cost troubleshooting step worth trying before assuming a major component (like the control board) needs replacement. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured to match the magnetic switch design and wire harness configuration of the original WH12X10334 lid switch assembly. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 3390291 Dryer Hi Limit Thermostat Replaces Part Numbers: WP3390291, 3390291, 696397, PS11741441, SET198, AP6008306, TJSET198, L250-80F Description: This Dryer High-limit thermostat is 2 wire, 250 degree limit, 60 degree cool down before reset. The high-limit thermostat cuts off power to the dryer if it overheats. If the thermostat has tripped, the dryer will not heat. To determine if the thermostat is defective, use a multi-meter to test it for continuity.   This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

XPARTCO 3406105 Dryer Door Switch Replaces WP3406105 The XPARTCO 3406105 is an aftermarket replacement dryer door switch assembly compatible with a wide range of Whirlpool-family dryers including Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Estate, Crosley, Inglis, Admiral, Jenn-Air, Magic Chef, and Norge. The door switch is a safety component mounted inside the dryer cabinet near the door opening. When the door is closed, the door strike depresses the switch actuator, completing the circuit and allowing the dryer to start and run. When the door is opened, the switch opens the circuit and stops the dryer. On models with a broken belt detection circuit, the door switch also plays a role in belt failure detection. A failed door switch causes the dryer to either not start at all or to run continuously with the door open. This is a Single Pole, Double Throw (SPDT) 3-wire switch with stainless steel terminals and a heat-resistant housing. It measures 1-3/4" L x 1-5/8" W x 1-1/4" H with a 7-3/4" wiring harness. Electrical specs are 120-240V, 50-60Hz, 11A, 1/3HP. The kit includes the switch and 3-wire harness assembly. It directly replaces WP3406105, 3406104, 3405104, 3405105, 528947, AP6008560, and several additional cross-reference numbers. Installs in 15–30 minutes with basic hand tools. Quick Answer The XPARTCO 3406105 Dryer Door Switch fixes Whirlpool-family dryers that won't start, won't stop when the door is opened, or require the door to be slammed to start. SPDT 3-wire switch, 120-240V/50-60Hz/11A/1/3HP. Body 1-3/4" L x 1-5/8" W x 1-1/4" H, 7-3/4" harness. Includes switch and harness assembly. Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, and more. Replaces WP3406105, 3406104, 3405104, 528947, AP6008560. Common Problems This Part Fixes Dryer will not start at all — door switch not completing the circuit when door is closed Dryer starts only when the door is slammed or held firmly closed Dryer continues to run after the door is opened — switch not opening the circuit Drum light not turning on when the door is opened (on models with drum light) Dryer starts intermittently — door switch contact worn and making unreliable contact Dryer stops mid-cycle randomly — switch opening the circuit due to vibration or wear Door switch visibly cracked, broken, or the actuator button no longer springs back Replaces Part Numbers This door switch directly replaces the following OEM and cross-reference part numbers: WP3406105, 3405104, 3405105, 3406104, 3406105, WP3406105VP, AWP47182, PD00003898, EAP11741700, AP6008560, PS11741700. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This door switch is compatible with select gas and electric dryers from the following brands: Whirlpool dryers (gas and electric) Kenmore / Sears dryers (Whirlpool-built models) Maytag dryers (gas and electric) KitchenAid dryers Amana dryers Roper dryers Estate dryers Crosley dryers Inglis dryers Admiral dryers Jenn-Air dryers Magic Chef dryers Norge dryers Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Safety switch — prevents dryer from operating when the door is open and stops the dryer immediately when the door is opened mid-cycle Single Pole, Double Throw (SPDT) 3-wire switch — provides both normally-open and normally-closed contacts for dryer start circuit and belt failure detection on compatible models Rated 120-240V, 50-60Hz, 11A, 1/3HP — correct electrical specifications for compatible Whirlpool-family dryers Switch body: 1-3/4" L x 1-5/8" W x 1-1/4" H; wiring harness: 7-3/4" L Stainless steel terminals and heat-resistant housing Kit includes switch and 3-wire harness assembly — complete plug-in replacement Replaces WP3406105, 3406104, 3405104, 3405105, 528947, and AP6008560 Compatible with 13 major appliance brands on the Whirlpool platform Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in 15–30 minutes with basic hand tools Product Specifications Part Number 3406105 OEM Part Number WP3406105 Part Type Dryer Door Switch Assembly (SPDT 3-Wire) Condition Aftermarket Replacement Application Gas and Electric Dryers Switch Type Single Pole, Double Throw (SPDT) Wires 3-wire Voltage 120-240V Frequency 50-60Hz Amperage 11A Horsepower 1/3 HP Switch Body Dimensions 1-3/4" L x 1-5/8" W x 1-1/4" H Harness Length 7-3/4 inches Color Off-White / Black / Gray Material Plastic / Metal (stainless steel terminals) Includes Switch and 3-wire harness assembly Compatible Brands Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Estate, Crosley, Inglis, Admiral, Jenn-Air, Magic Chef, Norge Installation Notes ⚠️ Unplug Dryer Before Starting Disconnect power (and shut off gas for gas dryers) before beginning. The door switch is located inside the dryer cabinet near the door opening, typically mounted in the front panel or top panel. Access it by inserting a putty knife under the top panel to release the spring clips and lift the top, then release the front panel. Locate the old door switch — it is a small rectangular component with a spring-loaded actuator button. Photograph the wiring connections before disconnecting. Disconnect the 3-wire harness from the old switch. Release the switch from its mounting bracket by pressing the retaining tabs and pulling the switch free, or unscrewing the mounting screw. Snap the new 3406105 switch into the mounting bracket and reconnect the 3-wire harness in the same positions. Reassemble the front and top panels, restore power, and run a test cycle to confirm the dryer starts, stops when the door is opened, and runs normally. Tools needed: Phillips screwdriver, putty knife. Frequently Asked Questions What does the dryer door switch do? The door switch is a safety component that monitors whether the dryer door is open or closed. When the door is closed, the door strike depresses the switch actuator, completing the electrical circuit and signaling the control board that it is safe to run. When the door is opened, the actuator releases, opening the circuit and stopping the dryer immediately. On many Whirlpool-family dryers, the 3-wire SPDT switch also provides a secondary circuit used for broken belt detection — one of the switch's contacts is part of the motor start circuit, while the other is part of a safety cutoff circuit. How do I test the door switch with a multimeter? Unplug the dryer and disconnect the switch from the harness. Set your multimeter to continuity mode. The 3406105 is an SPDT switch with three terminals — typically labeled Common (C), Normally Open (NO), and Normally Closed (NC). With the actuator button not pressed (door open position), you should read continuity between C and NC, and no continuity between C and NO. With the actuator button pressed (door closed position), you should read continuity between C and NO, and no continuity between C and NC. Any deviation from this pattern confirms the switch has failed. What is the difference between 3406105 and 3406104? The 3406104 was the original part number, and the 3406105 (later updated to WP3406105) is the current replacement that superseded it. They are the same door switch and are fully interchangeable. The 3405104 and 3405105 are also cross-references for this same switch from earlier production. If your dryer's documentation or old switch label shows any of these numbers, the 3406105 is the correct current replacement. Why does this switch have 3 wires when my old switch only had 2? The WP3406105 is an SPDT (Single Pole, Double Throw) switch with 3 terminals — Common, Normally Open, and Normally Closed. Some older dryer models used a simpler 2-wire switch, but the 3-wire WP3406105 is the updated replacement that works on both older and newer models. On models that originally had a 2-wire switch, only two of the three terminals are used — the third is simply left unconnected. Follow your model's wiring diagram or take a photo of the original switch's wire connections before removing it. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured from durable plastic and metal with stainless steel terminals to match the dimensions and electrical specifications of the original WP3406105 door switch assembly. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

EXP15A Ceramic Microwave Fuse Fast Blow 15A, 250V Replaces Part Numbers: WB27X7, 14QBP15CFB, AP2626454, PS240270, M0805102, AP6014670, WPM0805102, 3601-001197, PS4131368, AP4046099, PS239596, AP3189379, WB08T10027, WB2X8151, WB27X10454. This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less