Appliance Parts

XPARTCO DC96-00887C Dryer Thermal Cut Off Fuse The XPARTCO DC96-00887C is an aftermarket replacement thermal cut-off fuse for Samsung and select Kenmore electric dryers, mounted with its bracket on the blower housing. This fuse is a one-time safety device: as long as temperatures around the blower stay within normal range, it does nothing at all, but the instant they climb high enough — almost always from restricted airflow — the fuse permanently opens the circuit and cuts power to protect the dryer. That's why a blown fuse at this location produces such a specific symptom: the dryer won't start at all, with no lights, no tumble, and no response, even though the outlet has power. Despite frequently being labeled a "thermostat" on third-party marketplaces, this is genuinely a fuse, not a thermostat — once it opens from excess heat, it stays open permanently and cannot reset itself. It ships complete with its mounting bracket for a direct plug-in fit. A blown thermal fuse is almost always a symptom rather than a random failure: restricted exhaust venting is the leading cause, since trapped heat is exactly what this fuse is designed to react to. It directly replaces DC96-00887A, AP5966894, 2074129, AP4207819, PS4216838, EAP4216838, WP35001193, 35001193, PS11741822, PS11741829, and AP6008689. Quick Answer The XPARTCO DC96-00887C Dryer Thermal Cut Off Fuse fixes Samsung and select Kenmore electric dryers that won't start at all — no lights, no tumble, no response to any button. Mounted with bracket on the blower housing. Replaces DC96-00887A, AP5966894, 2074129, AP4207819, PS4216838, EAP4216838, WP35001193, 35001193, PS11741822, PS11741829, AP6008689. This is a different fuse from our DC47-00016A listing, which mounts on the heater can rather than the blower housing — always verify which fuse your dryer's parts diagram calls for. Common Problems This Part Fixes Dryer won't start at all — no lights, no tumble, no response to any button Dryer that stopped working suddenly, especially after running unusually hot Dryer runs a short time then shuts off completely and won't restart Repeated blown fuses on a dryer with a known venting or airflow restriction Clothes coming out extremely hot right before the dryer stopped working Continuity test shows an open circuit across the old fuse Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer thermal cut-off fuse directly replaces the following OEM and cross-reference part numbers: DC96-00887C, DC96-00887A, PD00035400, EAP4216838, AP5966894, ASM65115, PD00035400, PS4276292, WP35001193, 35001193, PD00003365, EAP11741829, AP6008689, AWP47381, PD00003365, PS11741829. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This thermal cut-off fuse is compatible with select Samsung electric dryers, and also fits select Kenmore dryers built on the Samsung platform, including model numbers such as: DV5471AEW/XAA DV40J3000EW/A2, DV42H5000EW/A3, DV45H7000EW/A2, DV48H7400EW/A2 DV400EWHDWR/AA DVE50M7450W/A3 Note — not the same as DC47-00016A: This fuse mounts on the blower housing. Our DC47-00016A listing is a separate thermal fuse that mounts on the heater can instead — the two guard different points in the same circuit and are not interchangeable. Always verify your full model number and check your parts diagram for the exact mounting location before ordering. Contact our support team with your model number if you're unsure which fuse your dryer needs. Key Features Aftermarket replacement thermal cut-off fuse — one-time safety device that cuts power if the dryer overheats Mounted with its bracket on the blower housing for a direct plug-in fit Resolves "won't start at all," "stopped working suddenly," and "clothes came out extremely hot before it died" symptoms caused by a blown fuse Genuinely a fuse, not a thermostat, despite common marketplace mislabeling — non-resettable once blown Replaces DC96-00887A, AP5966894, 2074129, AP4207819, PS4216838, EAP4216838, WP35001193, 35001193, PS11741822, PS11741829, and AP6008689 Compatible with Samsung and select Kenmore electric dryers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number DC96-00887C OEM Part Number DC96-00887C Part Type Dryer Thermal Cut-Off Fuse (with Bracket) Condition Aftermarket Replacement Location Blower housing Resettable No — one-time use, must be replaced once blown Related Component DC47-00018A high-limit thermostat (different device, same circuit, sold separately) Quantity 1 thermal fuse with bracket Compatible Brands Samsung, select Kenmore Installation Notes ⚠️ Unplug Dryer Before Starting — Inspect And Clean The Venting Before Reassembling Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access is typically through the rear panel: remove the screws securing the panel to reach the blower housing where the fuse is mounted. Photograph the wiring before disconnecting the old fuse's connectors. Remove the mounting screw holding the fuse and bracket in place, and pull it free, disconnecting both wire terminals. Before installing the new fuse, test it for continuity with a multimeter to confirm it's good out of the box, and test the old one to confirm it's actually blown (no continuity) rather than assuming. This is the most important step: fully inspect and clean the dryer's exhaust vent, from the lint trap housing all the way to the exterior vent hood, checking for lint buildup, crushed sections, or excessive length. A blown thermal fuse is a symptom of restricted airflow, and skipping this step means the new fuse is likely to blow again. Install the new DC96-00887C in the same mounting position, reconnect both wire terminals, and secure the mounting screw. Reinstall the rear panel, restore power, and run a test cycle to confirm normal heating and shutoff behavior. Tools needed: Phillips or nut driver (model-dependent), multimeter, vent brush or vacuum attachment for cleaning ductwork, work gloves. Frequently Asked Questions Some listings call this a "thermostat." Is it really a fuse? Yes, genuinely a fuse. This is a common point of confusion across the marketplace — many third-party sellers label DC96-00887C a "thermostat," but it functions as a one-time thermal cut-off fuse. Once it opens from excess heat, it stays open permanently and cannot reset itself, unlike a true thermostat, which closes again automatically once temperatures drop. If your fuse has blown, replacement is the only option regardless of what a given listing calls it. I replaced the fuse and it blew again. What's going on? This is a strong sign that the underlying cause — almost always restricted airflow — was never addressed. Thermal fuses don't fail from age; they blow because the dryer overheated. If a new fuse keeps blowing, thoroughly inspect and clean the entire exhaust path from the lint trap housing to the outside vent hood, checking for lint buildup, crushed or kinked ductwork, or a vent run that's too long. If airflow checks out and the fuse still blows, have the high-limit thermostat and thermistor checked as well, since a struggling thermostat can push this fuse to blow as the last line of defense. How is this different from your DC47-00016A listing? Both are one-time thermal fuses in the same dryer, but they mount in different locations and protect different points in the heating circuit. This DC96-00887C fuse is mounted on the blower housing; the DC47-00016A fuse is mounted on the heater can. They are not interchangeable, so check your parts diagram or the physical mounting location on your dryer to confirm which one you need. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured to match the electrical specifications, bracket configuration, and mounting position of the original DC96-00887C thermal fuse used in compatible Samsung and Kenmore electric dryers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO W10837240 Dryer Idler Pulley The XPARTCO W10837240 is an aftermarket replacement idler pulley assembly compatible with select Whirlpool, Maytag, Amana, Kenmore, KitchenAid, Crosley, Admiral, Inglis, and Roper dryers. The idler pulley maintains correct tension on the drive belt, allowing the belt to spin the dryer drum smoothly and consistently. When the idler pulley wears out, the belt loses tension — causing squeaking, grinding noises, or a drum that stops spinning entirely. This complete assembly includes the idler arm, pulley, and bracket — everything needed for a direct drop-in installation. The pulley is 2-1/8 inches in diameter and the overall assembly measures 6-1/4" L x 1-1/4" W x 3-7/16" H. It directly replaces OEM part numbers W10837240, W10547287, and W10547290, and fits Whirlpool-family dryers with the lint screen located inside the door. Installs in 15–30 minutes with basic hand tools. Quick Answer The XPARTCO W10837240 Dryer Idler Pulley fixes dryers that are squeaking, grinding, or have a drum that won't spin due to lost belt tension. Includes idler arm, pulley, and bracket. Pulley diameter 2-1/8". Compatible with select Whirlpool, Maytag, Amana, Kenmore, KitchenAid, Crosley, Admiral, Inglis, and Roper dryers. Fits models with lint screen inside the door. Common Problems This Part Fixes Loud squeaking or squealing noise during dryer operation Grinding or rumbling noise as the drum rotates Dryer drum not spinning — belt loses tension when pulley bearing fails Belt repeatedly slipping off or breaking due to improper tension Dryer drum turning erratically or stopping while motor continues to run Excessive vibration or shaking during the drying cycle Visible wear, cracking, or a pulley that no longer spins freely on its shaft Replaces Part Numbers This idler pulley assembly directly replaces the following OEM and cross-reference part numbers: W10837240, W10547287, W10547290, 3387372, 3388674, W10118754, W10118756, W10837240VP, PD00025564, FIX11726337, AP5988716, PS11726337, 279640, AP3094197, 279640VP, 2958, 3388672, 697692, TJ279640, W10468057, AH334244, EA334244, ER279640, PS334244. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This idler pulley is compatible with select dryers from the following brands: Whirlpool dryers (gas and electric — fits models with lint screen inside door) Maytag dryers (gas and electric) Amana dryers Kenmore / Sears dryers (select Whirlpool-built models) KitchenAid dryers Crosley dryers Admiral dryers Inglis dryers Roper dryers Important: The W10837240 fits Whirlpool-family dryers with the lint screen located inside the door. If your dryer has the lint screen on top of the cabinet, a different idler pulley may be required. Contact our support team with your model number to confirm before ordering. Key Features Maintains correct tension on the drive belt for smooth, consistent drum rotation every cycle Complete assembly — includes idler arm, 2-1/8" diameter pulley, and bracket — ready to install Overall dimensions: 6-1/4" L x 1-1/4" W x 3-7/16" H Durable plastic and metal construction — resists wear and heat damage Direct replacement for W10837240, W10547287, and W10547290 — no modification required Updated design replaces older W10547287 and W10547290 assemblies Aftermarket replacement built to OEM-equivalent quality standards Often replaced together with the drum belt (WPW10112954 or 661570V) for a complete drum drive repair DIY-friendly repair — installs in 15–30 minutes with basic hand tools Product Specifications Part Number W10837240 Part Type Dryer Idler Pulley Assembly with Arm and Bracket Condition Aftermarket Replacement Application Gas and Electric Dryers Pulley Diameter 2-1/8 inches Overall Dimensions 6-1/4" L x 1-1/4" W x 3-7/16" H Material Plastic / Metal Color White Includes Idler arm, pulley, and bracket assembly Lint Screen Location Fits dryers with lint screen inside the door Compatible Brands Whirlpool, Maytag, Amana, Kenmore, KitchenAid, Crosley, Admiral, Inglis, Roper Often Replaced With WPW10112954 or 661570V Drum Belt Installation Notes ⚠️ Safety First — Unplug Dryer Before Starting Unplug the dryer from the power source (and shut off the gas supply for gas dryers) before beginning any repair. Remove the lint screen and unscrew the Phillips screws inside the lint screen housing. Use a putty knife to release the top panel clips and lift the top panel. Remove the front panel to access the drum and drive components. Release the drive belt tension by pushing the idler arm, then slide the belt off the idler pulley. Remove the mounting screw securing the old idler arm assembly and lift it out. Install the new W10837240 idler assembly, secure with the mounting screw, then re-route the drive belt around the new pulley and motor pulley. Reassemble the front panel, top panel, and restore power before running a test cycle. Tip: While the dryer is open, inspect the drum belt (WPW10112954) and drum support rollers for wear and replace if needed. Tools needed: Phillips screwdriver, putty knife or flat pry tool. Frequently Asked Questions What does the idler pulley do? The idler pulley is a spring-tensioned wheel mounted on an arm and bracket inside the dryer. It presses against the drive belt to maintain the correct tension needed to keep the belt gripping the drum and motor pulley. Without proper tension, the belt slips, loses contact, or causes the drum to stop spinning. A worn or seized idler pulley is one of the most common causes of dryer squeaking and drum spin failure. Does W10837240 replace W10547287 and W10547290? Yes. The W10837240 is the updated part number that directly supersedes both the W10547287 and W10547290 idler pulley assemblies. If your dryer originally used either of those older part numbers, the W10837240 is the correct current replacement. How do I know if my lint screen is inside the door? Open the dryer door and look for a slot or housing just inside the door opening — typically at the top or bottom of the door opening — where you pull out the lint filter. If the filter pulls out from inside the door frame, the W10837240 is designed for your dryer style. If the lint screen pulls out from the top of the dryer cabinet, contact our support team with your model number to identify the correct idler pulley for your machine. Should I replace the drive belt at the same time? Yes — since the dryer is already disassembled to replace the idler pulley, it is highly recommended to also inspect and replace the drum belt (WPW10112954) at the same time. The belt and idler pulley wear together, and a worn belt on a new pulley — or vice versa — significantly shortens the life of the new part. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured from durable plastic and metal to match the dimensions and performance of the original W10837240 idler pulley assembly. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

137292700 Genuine OEM Dryer Drum Belt Product Title 137292700 Dryer Genuine OEM Drum Belt - Compatible with Frigidaire, Electrolux, Kenmore Dryers Product Description Keep your dryer running smoothly with the Genuine OEM 137292700 Dryer Drum Belt from Parts-O-Matic. This Genuine OEM belt, measuring approximately 89.5" long with 4 ribs and 3 grooves, drives the dryer drum to ensure efficient tumbling and drying. Compatible with select Frigidaire, Electrolux, Kenmore, Gibson, Kelvinator, Tappan, and White-Westinghouse dryers, this belt fixes issues like failure to tumble, unusual noises, or insufficient heat. Enjoy free shipping on all orders at Parts-O-Matic! Key Features: ✅ Broad Compatibility: Fits select Frigidaire, Electrolux, Kenmore, Gibson, Kelvinator, Tappan, and White-Westinghouse dryer models. 🔥 Reliable Performance: 89.5" flat belt with 4 ribs and 3 grooves ensures smooth drum rotation and efficient drying. 💰 Cost-Effective Alternative: Genuine OEM part offers OEM-equivalent performance at a lower price. 🛠️ Easy Installation: Requires basic tools (Phillips screwdriver, putty knife) and 20–30 minutes for DIY repair. 🛡️ Fixes Common Issues: Resolves drum not tumbling, squealing or thumping noises, or insufficient heat production. Compatibility: Compatible with models including but not limited to: Frigidaire: FEX831FS2, FEQ332ES0, FER231AS2, AGQ6000ES2 Electrolux: EIMED55IIW0, EIMED60JIW0 Kenmore: 417.91702001, 417.97812700, 417.97812702 Replaces part numbers: 137292700, 134163500, 134503900, 5303283287, AH3408299, EA3408299, AP4565702, PS3408299. Verify compatibility with your appliance brand and model number, please contact Parts-O-Matic support for assistance. Tips: Vacuum lint and debris from the dryer interior to prevent belt wear. Ensure proper pulley alignment to extend belt life. If the belt feels loose or slips, check the idler pulley tension. Download our installation guide or watch our YouTube tutorial for step-by-step instructions. Caution: Avoid stretching the belt during installation, as this can reduce its lifespan. Shop Parts-O-Matic for Genuine OEM appliance parts with free shipping on all orders and a 30-day return policy. Get your dryer tumbling perfectly again today! Add to cart now for an affordable fix with free shipping on your entire order!

Read more less

285785 Washer Transmission Clutch - Compatible with Whirlpool, Kenmore, KitchenAid, Maytag, Amana, Roper, and Other Washers Product Description Restore your washer’s performance with the replacement 285785 Washer Transmission Clutch. This high-quality replacement clutch assembly, designed for direct-drive (beltless) Whirlpool, Kenmore, KitchenAid, Maytag, Amana, Roper, and other washer models, connects the transmission to the inner tub during the spin cycle and the agitator during the wash cycle. Constructed from durable plastic and metal, this clutch assembly includes a clutch with liner, brake cam driver, retaining clip, blue spring for large capacity (27") washers, and black spring for compact (24") washers. It addresses issues like slow spinning, failure to agitate, burning smells, or excessive shaking. Note: Includes one clutch assembly with hardware. Disconnect power before installation. Replaces part numbers: 285785, 2670, 285331, 285380, 285422, 285540, 285761, 285785VP, 3350015, 3350114, 3350115, 3351342, 3351343, 387888, 388948, 388949, 3946794, 3946847, 3951311, 3951312, 62699, 63174, 63765, 64176, PD00002503, EAP334641, AH334641, EA334641, J27-662, LP326, AP3094537, PS334641. Compatibility: Compatible with models including but not limited to: Whirlpool: WTW5300SQ0, LSR7233EQ0, LSR8433KQ0, LSQ9544KQ0 Kenmore: 110.26902690, 110.28762790, 110.29822800 KitchenAid: KAWS750JQ0, KAWS850JQ0 Maytag: MAV6451AWW, MAV9750AWW Amana: NTW4500XQ0 Roper: RAS8245EQ1, RTW4440XQ0 Inglis: ITW4300SQ0 Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Whirlpool, Kenmore, KitchenAid, Maytag, Amana, Roper, Inglis, and other direct-drive washer models. 🔥 Specifications: replacement clutch assembly, plastic and metal, 4-1/2"L x 4-1/2"W x 1-1/8"H, includes clutch w/liner, brake cam driver, retaining clip, blue spring (1.24" for large capacity 27" washers), black spring (1.46" for compact 24" washers). 💰 Cost-Effective Alternative: replacement clutch offers OEM-equivalent performance at a lower price. 🛠️ Easy Installation: Requires a socket set, screwdrivers, work gloves; typically installed in 1–2 hours. 🛡️ Reliable Fixes: Resolves slow spinning, failure to agitate, burning smells, excessive shaking, or noisy operation. Installation Notes: Safety First: Disconnect the washer from the power source before installation. Shop Parts-O-Matic for high-quality replacement appliance parts with a 30-day return policy. Keep your washer spinning and agitating smoothly today! Add to cart now for a budget-friendly fix!

Read more less

XPARTCO EXP497 Microwave Door Switch (Normally Open) The XPARTCO EXP497 is an aftermarket replacement Normally Open (NO) microwave door interlock switch compatible with a wide range of GE, Whirlpool, Samsung, LG, Frigidaire, Kenmore, Panasonic, and Sharp microwaves. The door interlock switch is one of several safety switches in the microwave door system. It allows the microwave to operate only when the door is fully closed — when the door closes, the switch is mechanically activated, completing the circuit and signaling the control board that it's safe for the magnetron to fire. When the door is open, the switch is released and the circuit is broken, preventing the microwave from generating microwave radiation. This switch is rated for 16A at 125/250V AC, giving it the heavy-load capacity required for microwave door safety circuits. It directly replaces an extensive list of cross-reference part numbers from multiple manufacturers, including 3B73362F, SZM-V16-FA-63, WB24X816, WB24X829, WB24X10180, 6600W1K003C, WP56001036, 5304408938, AP4437957, PS3522738, and dozens more. Important: confirm your original switch is a Normally Open (NO) type before ordering — this part will not replace Normally Closed (NC) or COM-style switches. Installs in 15–25 minutes with basic hand tools. Quick Answer The XPARTCO EXP497 Microwave Door Switch (Normally Open) fixes microwaves that won't start, won't heat, stop mid-cycle, or won't shut off when the door opens. Universal-fit Normally Open (NO) interlock switch, 16A at 125/250V AC. Replaces 3B73362F, SZM-V16-FA-63, WB24X816, WB24X829, WB24X10180, 6600W1K003C, WP56001036, 5304408938, AP4437957, PS3522738 (and many more). Compatible with GE, Whirlpool, Samsung, LG, Frigidaire, Kenmore, Panasonic, and Sharp microwaves. Important: confirm your original switch is "Normally Open" before ordering. Common Problems This Part Fixes Microwave won't start when the door is closed and the start button is pressed Microwave runs but produces no heat — turntable spins, light works, but food doesn't warm Microwave starts and then immediately stops mid-cycle Microwave continues running with the door open (unsafe failure mode — replace immediately) Intermittent start failure — works sometimes, doesn't work other times Door switch button visibly stuck, broken, or fails to click when pressed Multimeter continuity test on the switch shows it doesn't change state when actuated Replaces Part Numbers This Normally Open microwave door switch directly replaces an extensive list of OEM and cross-reference part numbers: 3B73362F, 3B73362E, 6600W1K003D, 6600W1K004C, 6600W1K004F, AH3522738, EA3522738, AP4437957, PS3522738, WB24X816, WB24X0816, AP2024324, QSWMA085WRE0, QSWMA168WRZZ, WB24X10180, AH2370055, EA2370055, AP4484237, PS2370055, 00606693, 00415824, 1386418, 35-00-780, 415824, 606693, AH3477005, EA3477005, PS3477005, AP4070531, PS8726630, 00633795, 00415825, 35-00-781, 415825, 4162223, AP5952985, PS10060855, WB23X10019, 1810578, AH3486591, EA3486591, AP4980343, PS3486591, WB24X10204, WB24X10148, WB24X28940, 251201600929, 3025958, AP5790848, PS8754454, 5304408938, 5304430284, 639405, AH471434, EA471434, AP2151217, PS471434, WB24X10047, WB24X10029, WB24X0815, WB24X10072, WB24X10113, WB24X815, AH237015, EA237015, AP2622452, PS237015, 5304408938, 5304430284, 639405, AH471434, EA471434, AP2151217, PS471434, 5304423463, 892734, AH472733, EA472733, AP2151744, PS472733, 5304493153, 5304440026, 3018427, 5303319558, 5304467694, 75304440026, 75304467694, AP5804011, PS8769124, WB24X10139 1086028, AH953555, EA953555, PS953555, AP3792702, WB24X10140 AH953556, EA953556, AP3792654, PS953556, WB24X829, WB24X10038, WB24X368, WB24X384, WB24X414, WB24X426, WB24X439, WB24X441, WB24X445, WB24X796, WB24X5228, WB24X796, AP2024337, AH237421, EA237421, PS237421, WP56001036, 56001036, 0053464, R0654097, AP6009674, PS11742843, 3405-001034, 3405-000178, 111698, 2028597, AP4044834, PS4131192, WB24X823, WB24X0820, WB24X0823, WB24X820, AH237415, EA237415, AP2024331, PS237415, 5304509460, 5304520020, 5304464099, 4583656, AP6230615, PS12071303, WB24X28941, AH1019163, EA1019163, MW-7100-33, AP3866977, PS1019163, 5304493153, 5304440026, 3018427, 5303319558, 5304467694, 75304440026, 75304467694, AP5804011, PS8769124, D3V-16G-3C25, SZM-V16-FA63. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This Normally Open door switch is compatible with select microwaves from a wide range of brands: GE microwaves (countertop, over-the-range, and built-in models) Whirlpool microwaves Samsung microwaves LG microwaves — MV, LMV, LMH, MQ, MS, LMA, LMVM series (MV1560M, MV1310W, MV1560T, LMV1625B, LMA2112WT, MS1443ASV, LMH1017CVST and many more) Frigidaire microwaves Kenmore / Sears microwaves (multi-brand built models) Panasonic microwaves Sharp microwaves Bosch microwaves (select models — cross-references 00606693, 00633795) Important — Confirm Switch Type Before Ordering: This is a Normally Open (NO) switch. Microwaves typically use 2–3 door switches: one Normally Open and one or two Normally Closed/COM. They are not interchangeable. Inspect your original switch's markings or test it with a multimeter before ordering — if your failed switch is Normally Closed, you need the EXP499 instead. If you're unsure, contact our support team with your microwave model number. Key Features Normally Open (NO) microwave door interlock switch — closes the circuit when the door is closed, allowing the microwave to operate Rated 16A at 125/250V AC — heavy-duty capacity for microwave door safety circuits Universal fit — replaces door switches from GE, Whirlpool, Samsung, LG, Frigidaire, Kenmore, Panasonic, Sharp, and Bosch Replaces 50+ OEM and aftermarket cross-reference part numbers across multiple appliance brands Common alternate part numbers include 3B73362F, SZM-V16-FA-63, D3V-16G-3C25, AP4437957, and PS3522738 Important: verify your switch is Normally Open before ordering — NOT a replacement for Normally Closed (use EXP499) or COM-style switches Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 15–25 minutes with basic hand tools Product Specifications Part Number EXP497 Part Type Microwave Door Interlock Switch (Normally Open) Condition Aftermarket Replacement Application Microwaves (cross-brand) Switch Type Normally Open (NO) Max Current 16A Voltage Rating 125/250V AC Common OEM Equivalents 3B73362F, SZM-V16-FA-63, D3V-16G-3C25 Compatible Brands GE, Whirlpool, Samsung, LG, Frigidaire, Kenmore, Panasonic, Sharp, Bosch Installation Notes ⚠️ High-Voltage Safety Warning — Microwave Capacitor Microwaves contain a high-voltage capacitor that can hold a lethal electrical charge even after the appliance is unplugged. Before opening the microwave cabinet to access the door switches, always unplug the unit and discharge the high-voltage capacitor using proper safety procedure (with an insulated screwdriver across the capacitor terminals while wearing insulated gloves). If you are not familiar with safely discharging a microwave capacitor, have this repair done by a qualified technician. ⚠️ Wear Work Gloves — Identify Switch Position Before Removing Disconnect power before beginning. Wear work gloves to protect your hands. After safely discharging the high-voltage capacitor, remove the microwave's outer cabinet or control panel as needed to access the door interlock switch assembly — typically located behind the right side of the door frame on most microwaves. Take a photo of all switch positions and wire connections before disconnecting anything. Microwaves usually have 2–3 switches in the door interlock assembly: confirm which one is the Normally Open switch (the EXP497 fits this position only). Disconnect the wires from the old switch — make a note of which wire goes where. Release the switch from its mounting tabs and pull it free. Install the new EXP497 in the same position with the same wire connections. Reassemble the cabinet, restore power, and test the microwave by closing the door and confirming it starts and heats normally, then opening the door and confirming it shuts off immediately. Tools needed: Phillips screwdriver, work gloves, insulated tools (for capacitor discharge). Frequently Asked Questions What's the difference between a Normally Open and Normally Closed microwave door switch? Microwave door interlock systems use both types together to provide redundant safety. A Normally Open (NO) switch — like the EXP497 — has open contacts at rest; when the door closes and pushes the switch button, the contacts close to complete a circuit, signaling "door closed." A Normally Closed (NC) switch is the opposite — contacts are closed at rest and open when the door pushes the button. Most microwaves use one or more of each type wired together so the control system can confirm the door is genuinely closed from multiple inputs. They are not interchangeable — you must replace each switch with the same type. If your switch is NC, order the EXP499 instead. How do I know if I need the Normally Open or Normally Closed switch? The easiest way is to read the part number printed on the side of the failed switch and compare it to the cross-reference lists for the EXP497 (Normally Open) versus the EXP499 (Normally Closed). If the markings are unreadable, you can also test the switch with a multimeter set to continuity mode: with the switch at rest (button released), a Normally Open switch reads open (no continuity) and a Normally Closed switch reads closed (continuity). Replacing each switch with the same type is essential — installing the wrong type can prevent the microwave from starting or create unsafe conditions. My microwave runs but doesn't heat — could this be the door switch? Yes — this is one of the most recognizable symptoms of a failed door switch in a multi-switch interlock system. A microwave that turns on (light, fan, turntable) but does not heat often has a failed door switch in one of the door positions while the others continue to work. The control system may allow the auxiliary components to run but blocks the magnetron from firing without confirmation from all switches. Check all door switches systematically — one Amazon review noted a customer needed three identical switches to fully repair their microwave because the third switch (at the top of the door) was the actual cause of the no-heat condition. Replacing all door switches together is a common approach. My microwave keeps running with the door open — what should I do? This is a serious safety concern. Disconnect power to the microwave immediately and do not use it until the door switch is replaced. A microwave that continues to run with the door open exposes you to microwave radiation, which can cause serious injury. This usually indicates one or more door switches are stuck in the "door closed" position. Replace the failed switches with matching NO or NC type (EXP497 for NO, EXP499 for NC) before using the microwave again. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a manufacturer-branded OEM switch from any single brand, but is manufactured to match the dimensions, contact configuration, and 16A/125-250V AC rating of the dozens of OEM door switches it cross-references across multiple appliance brands. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO XP311 Dryer Thermostat Kit for LG The XPARTCO XP311 is an aftermarket replacement 3-piece thermostat kit for LG electric dryers, bundling the thermal fuse, thermistor, and high-limit thermostat that work together to regulate and protect the dryer's heating system. These three components monitor heat continuously during normal operation and step in at different thresholds if something goes wrong, which is why they're commonly replaced as a set — a single overheating event or a slow age-related drift in one part can put stress on the others, and buying them together also saves a second teardown if one of the remaining parts fails soon after. This kit includes: the 6931EL3003D thermal fuse, a one-time safety device that permanently cuts power to the dryer if internal temperatures climb dangerously high; the 6323EL2001B thermistor, a temperature sensor assembly with wire harness that continuously reports drum temperature to the control board so it can regulate heat output during the cycle; and the 6931EL3001E high-limit thermostat, which automatically shuts off the heating element if the dryer's temperature exceeds safe operating limits, without needing to be replaced like the thermal fuse does. Symptoms of failure in this circuit include incomplete drying, insufficient heating time, overheating that damages clothing, and the dryer shutting down prematurely or failing to start at all. It directly replaces AP4440975, 1268366, 6931EL3003E, AH3530485, EA3530485, PS3530485 (thermal fuse); AP4441539, 1268206, 6323EL2001H, AH3529026, EA3529026, PS3529026 (thermistor); and AP4440977, 1268363, 6931EL3001B, 6931EL3001C, AH3530481, EA3530481, PS3530481, 6931EL3001F (high-limit thermostat). Quick Answer The XPARTCO XP311 Dryer Thermostat Kit fixes LG (and select Kenmore) electric dryers with incomplete drying, insufficient heat, overheating that damages clothes, or a dryer that shuts down prematurely or won't start. 3-piece kit: thermal fuse (6931EL3003D), thermistor (6323EL2001B), and high-limit thermostat (6931EL3001E). Replaces 6323EL2001B, 6931EL3001E, 6931EL3003D, and their full cross-reference sets listed below. These three parts share the same circuit and commonly fail together — replacing all three at once is standard practice when one has failed. What's In The Kit Component Part Number Function Thermal Fuse 6931EL3003D One-time safety device — permanently cuts power if the dryer overheats. Cannot be reset once blown. Thermistor 6323EL2001B Continuously senses drum temperature and reports it to the control board to regulate heat output. High-Limit Thermostat 6931EL3001E Automatically shuts off the heating element if temperature exceeds safe limits. Resets automatically, unlike the thermal fuse. Common Problems This Kit Fixes Dryer runs but clothes come out only partially dry Insufficient heating time or reduced heat output Overheating that scorches or damages clothing Dryer shuts down prematurely mid-cycle Dryer won't start at all Inconsistent drying results from cycle to cycle Dryer that recently blew a thermal fuse and needs the related components checked Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer thermostat kit directly replaces the following OEM and cross-reference part numbers: 6931EL3003D, 1268366, AH3530485, EA3530485, PD00001818, EAP3530485, AP4440975, PS3530485, 6323EL2001B, 1268206, 6323EL2001H, AH3529026, PD00001821, EAP3529026, EA3529026, AP4441539, PS3529026, 6931EL3001E, 1268363, 6931EL3001C, PD00023869, EAP3530481, AH3530481, EA3530481, AP4440977, PS3530481. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This kit is compatible with select LG electric dryers, and also fits select Kenmore dryers built on the LG platform, including model numbers such as: CDE3379WN DLE0332W, DLE0442G, DLE0442W, DLE0442W01 DLE1310W, DLE2101W, DLE2140W, DLE2240W DLE2512W, DLE2514W, DLE2515S, DLE2516W, DLE2522W, DLE2524W, DLE2532W DLE3733D, DLE3733S, DLE5955W Note: This kit is for LG electric dryers. Different resistance values, dimensions, and mounting methods apply across brands and models, so always verify your full model number before ordering rather than relying on physical resemblance alone. Contact our support team with your model number if you're unsure. Key Features Complete 3-piece kit — thermal fuse, thermistor, and high-limit thermostat in one purchase Addresses the full temperature-regulation and safety circuit at once, rather than piecemeal Resolves "incomplete drying," "insufficient heat," "overheating," and "premature shutdown" symptoms Thermistor ships with its wire harness included No special tools required for installation Direct drop-in replacement for all three original components Replaces the full cross-reference set for 6931EL3003D, 6323EL2001B, and 6931EL3001E listed above Compatible with LG and select Kenmore electric dryers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Kit Part Number XP311 Kit Contents 1x Thermal Fuse (6931EL3003D), 1x Thermistor (6323EL2001B), 1x High-Limit Thermostat (6931EL3001E) Condition Aftermarket Replacement Application LG Electric Dryers Thermal Fuse Type One-time use, non-resettable High-Limit Thermostat Type Automatically resetting Thermistor Includes wire harness Repair Difficulty Easy to Moderate — no special tools required Compatible Brands LG, select Kenmore Installation Notes ⚠️ Unplug Dryer Before Starting — Test Before Assuming All Three Have Failed Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access is typically through the rear panel or the front, depending on your model — these components are commonly mounted on or near the blower housing and heater duct assembly. Photograph the wiring connections before disconnecting anything, since the thermal fuse, thermistor, and high-limit thermostat can look similar and are easy to swap positions by mistake. Before installing the full kit, it's reasonable to test each old component with a multimeter to confirm which have actually failed — the thermal fuse and high-limit thermostat can each be checked for continuity, though replacing all three together is still standard practice given how this circuit tends to fail. Remove each old component from its mounting position, noting orientation, and disconnect its wiring. Install each new component from the kit in the same position and orientation as the part it replaces, reconnecting wiring exactly as photographed. Reassemble the panel, restore power, and run a full test cycle to confirm normal heating, consistent drying, and no premature shutoffs. Tools needed: Phillips or nut driver (model-dependent), multimeter (recommended), work gloves. Frequently Asked Questions Do I really need to replace all three parts, or can I just replace the one that failed? You can test each component individually with a multimeter and replace only the ones that fail, but there's a good reason these are commonly sold and replaced together: they share the same heating circuit and tend to age or fail around the same time, especially if an overheating event caused the original failure. Replacing all three at once avoids a second teardown if one of the remaining original parts fails again soon after. What's the difference between the thermal fuse and the high-limit thermostat? They sound similar. Both protect against overheating, but they behave very differently. The high-limit thermostat is the first line of defense — it shuts off the heating element automatically if temperature climbs too high, then resets itself once things cool down, letting the dryer resume normal operation. The thermal fuse is the backup: if temperatures climb high enough that the thermostat alone doesn't prevent a dangerous overheat, the fuse permanently opens the circuit and cuts all power. Unlike the thermostat, the fuse cannot reset itself and must be physically replaced once it blows. What does the thermistor actually do, and why does it matter if it's a sensor rather than a switch? The thermistor doesn't switch anything on or off directly — it's a variable resistor whose resistance changes with temperature, and the control board reads that resistance continuously to know exactly how hot the drum is running. That ongoing feedback is what lets the control board fine-tune heat output throughout the cycle rather than just running hot or cold. A failing thermistor can cause the control to misjudge temperature, leading to insufficient heat, inconsistent drying, or the control cutting the cycle short. My dryer blew a thermal fuse. Should I get this whole kit instead of just the fuse? It's worth considering, especially since a blown thermal fuse usually means the dryer actually overheated at some point — and that same overheating event can stress the thermistor and high-limit thermostat even if they haven't failed outright yet. Also worth checking regardless of which parts you replace: restricted exhaust venting is the most common root cause of dryer overheating, so inspect and clean the vent ducting when you do this repair, or the new parts may face the same stress that damaged the originals. Is this an OEM or aftermarket kit? This is an aftermarket replacement kit built to OEM-equivalent quality standards. It is not a genuine LG OEM kit, but each component is manufactured to match the electrical specifications, resistance values, and mounting configuration of the original 6931EL3003D thermal fuse, 6323EL2001B thermistor, and 6931EL3001E high-limit thermostat used in compatible LG electric dryers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO W11688995 Washer Water Inlet Valve (Cold) The XPARTCO W11688995 is an aftermarket replacement cold water inlet valve designed as a direct fit for select Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, Magic Chef, Admiral, Norge, Roper, Inglis, and Kenmore front-load washers. The cold water inlet valve is mounted at the back of the washer where the cold water supply hose connects. When the washer's control board calls for cold water during a wash cycle, the valve's internal solenoid opens, letting water flow into the tub or detergent dispenser. The valve closes the instant the control board cuts power, stopping flow precisely as the correct fill level is reached. When this valve fails, the washer may not fill with cold water at all, fill very slowly, fail to dispense fabric softener, continuously drip water into the tub even when off, or display F8E1 or LO FL error codes. Construction is blue and white plastic with metal solenoid coil, ~3"H x 4"W x 3"L, with 1/2" NPT threaded inlet for standard washer supply hose. It directly replaces W11688995, W11036930, W11316256, W11486361, AP7218603, EAP12711564, PD00086086, PS12711564, 4929298, and AP6835737. Often replaced as a pair with the hot water inlet valve (W11688994, sold separately). Installs in 10–15 minutes with basic hand tools. Quick Answer The XPARTCO W11688995 Washer Water Inlet Valve (Cold) fixes Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, and Kenmore front-load washers displaying F8E1 or LO FL error codes, not filling with cold water, filling slowly, failing to dispense fabric softener, or continuously dripping into the tub. Blue/white plastic with metal coil, 1/2" NPT thread, ~3"H x 4"W x 3"L. Replaces W11036930, W11316256, W11486361, AP7218603, EAP12711564, PD00086086, PS12711564, 4929298, AP6835737. Often paired with the hot water valve (W11688994, sold separately). Common Problems This Part Fixes Washer not filling with cold water — valve solenoid not opening when commanded Washer filling slowly with cold water — valve partially clogged or weak solenoid F8E1 error code displayed — cold water inlet valve fault LO FL (low flow) error code — valve unable to deliver normal water flow Fabric softener not being dispensed — cold water flush to dispenser failing Water continuously dripping into the tub when the washer is off — valve stuck open or not fully closing Water leaks at the valve body — internal seal failure Wash cycles taking much longer than normal due to slow fill Replaces Part Numbers This cold water inlet valve directly replaces the following OEM and cross-reference part numbers: W11688995, W11316256, W11036930, W11486361, 4983050, PD00086086, FIX17216730, EAP17216730, OEM28874414, AP7218603, AWP46809, PS17216730. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This cold water inlet valve is compatible with select front-load washers from the following brands: Whirlpool front-load washers — WFC6810LW0, WFC9820HC0, WFC9820HW0 series Whirlpool front-load washers — WFW560CHW0, WFW560CHW1, WFW560CHW2, WFW560CHW3, WFW560CHW4 series Whirlpool front-load washers — WFW5605MC0, WFW5605MW0 series Whirlpool front-load washers — WFW5620HW0, WFW5620HW1, WFW5620HW2, WFW5620HW3 series Whirlpool front-load washers — WFW6620HC0, WFW6620HC1, WFW6620HC2, WFW6620HW0, WFW6620HW1 series Whirlpool front-load washers — WFW8620HC0, WFW8620HC1, WFW8620HC2, WFW8620HC3, WFW8620HC4, WFW8620HW0, WFW8620HW1, WFW8620HW2, WFW8620HW3, WFW8620HW4 series Whirlpool front-load washers — WFW862CHC0, WFW862CHC1, WFW862CHC2, WFW862CHC3 series Whirlpool front-load washers — WFW9620HBK1, WFW9620HBK2, WFW9620HBK3, WFW9620HC0, WFW9620HC1, WFW9620HC3, WFW9620HW0, WFW9620HW1, WFW9620HW2, WFW9620HW3 series Maytag front-load washers — MHW5630HC0, MHW5630HW1, MHW5630MBK0 series and related Amana front-load washers — NFW5800HW0, NFW5800HW1 and related models Inglis front-load washers — IFW5900HW, IFW5900HW1 and related models KitchenAid, Jenn-Air, Magic Chef, Admiral, Norge, Roper front-load washers — select Whirlpool-built models Kenmore / Sears front-load washers — select Whirlpool-built models Note: This is the cold water inlet valve (typically blue). The matching hot water inlet valve is part number W11688994 (typically red). When you replace one valve, it's a good practice to replace the other at the same time since they're the same age, both are accessible during the same repair, and the second valve will likely fail in the near term. Always verify your model number before ordering. Key Features Aftermarket replacement built to OEM-equivalent quality standards Controls the flow of cold water into the washer during fill cycles Solenoid-actuated — opens precisely when the control board calls for cold water and closes the moment the call is dropped Resolves F8E1 and LO FL error codes when caused by a failed cold inlet valve 1/2" NPT threaded inlet for standard washer supply hose connection Dimensions: approximately 3" H x 4" W x 3" L Blue and white plastic body with metal solenoid coil — designed for long-term reliability against wash cycle pressure and temperature Replaces W11036930, W11316256, W11486361, AP7218603, EAP12711564, PD00086086, PS12711564, 4929298, and AP6835737 Compatible with Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, Magic Chef, Admiral, Norge, Roper, Inglis, and Kenmore front-load washers Often replaced together with the hot water inlet valve (W11688994, sold separately) as a paired repair Quick DIY repair — installs in 10–15 minutes with basic hand tools Product Specifications Part Number XPW11688995 Part Type Washer Water Inlet Valve (Cold) Condition Aftermarket Replacement Application Front-Load Washers (Whirlpool platform) Water Type Cold (paired hot valve is W11688994) Inlet Thread 1/2" NPT Dimensions Approximately 3" H x 4" W x 3" L Color Blue / White Material Plastic / Metal Error Codes Resolved F8E1, LO FL (when caused by cold valve fault) Often Paired With Hot Water Inlet Valve (W11688994, sold separately) Compatible Brands Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, Magic Chef, Admiral, Norge, Roper, Inglis, Kenmore Installation Notes ⚠️ Unplug Washer and Shut Off Water Supply Before Starting — Wear Work Gloves Disconnect power and shut off both the hot and cold water supplies at the wall before beginning. Wear work gloves to protect your hands. Have towels ready — residual water remains in the supply hoses and will spill when disconnected. Pull the washer out from the wall to access the back. Remove the three 1/4" screws securing the rear edge of the top cover, push the top cover slightly back, and lift it off. Locate the inlet valves at the back of the washer — the cold valve is typically blue. Disconnect the cold water supply hose from the valve (water will drip — towels). Photograph the wire connections before disconnecting. Unplug the small electrical connector from the valve solenoid. Remove the single 3/16" mounting screw (or similar hardware, model-dependent) holding the valve in place, and disconnect any internal water hoses from the valve outlet (channel-lock pliers may help with hose clamps). Install the new W11688995 valve in the same position with the same orientation, reconnect the internal water hoses and electrical connector, and secure the mounting screw. Reconnect the cold supply hose at the wall, restore water and power, and run a test cycle to confirm normal cold water fill with no leaks. Tip: while the top cover is off, this is the ideal time to also replace the hot water valve (W11688994) — they share the same access and lifespan. Tools needed: 1/4" nut driver, 3/16" nut driver, adjustable wrench or pliers, work gloves. Frequently Asked Questions What do error codes F8E1 and LO FL mean on Whirlpool washers? Both codes indicate a water fill problem. F8E1 appears when the control board doesn't detect normal water flow during a fill cycle — typically caused by a failed inlet valve, a clogged inlet screen, kinked supply hose, or restricted water supply. LO FL (low flow) appears when the washer detects that water is flowing in, but at a rate too low to complete the fill within the expected time window. When the cold water inlet valve has failed or is partially clogged, both codes can appear together. Before replacing the valve, check that the household cold water supply is on and the supply hose isn't kinked, and inspect the inlet screen on the valve for sediment buildup. If those check out, replacing the W11688995 typically resolves the codes. My washer isn't dispensing fabric softener — could this be the cold valve? Yes — this is actually a common symptom that's often misdiagnosed. The cold water inlet valve also feeds the detergent dispenser tray on most Whirlpool front-load washers, including the fabric softener compartment. If the cold valve is clogged or failing to fully open at the right moment in the cycle, water doesn't flow through the fabric softener compartment to flush it into the tub, leaving softener pooled in the tray at the end of the cycle. If you've already cleaned the dispenser tray and water lines and the problem persists, replacing the cold inlet valve (W11688995) often resolves the issue. Should I replace the hot water valve at the same time? Yes, it's strongly recommended. The cold and hot inlet valves are essentially identical components installed side by side at the back of the washer — they're the same age, are exposed to the same wash cycle stress, and have the same expected service life. When one fails, the other is typically not far behind. Since the top cover is already off and both valves are accessible during the same repair, replacing both saves you a second teardown later. The matching hot water valve is part number W11688994 (red, sold separately) and is also available as a paired kit. My washer is dripping water into the tub even when it's off — is this the valve? Yes, that's a classic sign of a failed inlet valve. When the solenoid wears out or debris keeps the valve from sealing fully closed, water leaks past it at low rates and drips into the tub even with the washer powered off — especially noticeable as a slow puddle forming over a day or two. Since both the hot and cold valves feed into the tub, you'll want to identify which one is leaking: shut off the hot water supply at the wall and check if dripping continues. If it stops, the hot valve is at fault; if it continues, this cold valve is the cause. Replacing the W11688995 will resolve a leaking cold valve. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the dimensions, electrical specifications, 1/2" NPT thread, and solenoid function of the original W11688995 cold water inlet valve used in compatible Whirlpool, Maytag, Amana, KitchenAid, and Kenmore front-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WD21X10519 Dishwasher Flood Switch – Compatible with GE, Hotpoint, and RCA Dishwashers Product Description Prevent overfilling and protect your dishwasher from water damage with the XPARTCO WD21X10519 Dishwasher Flood Switch. This Flood Switch Assembly is a replacement part compatible with GE dishwashers. The dishwasher flood switch and thermistor assembly is responsible for detecting and preventing water from overflowing the dishwasher. It is located at the base of the tub and detects when water is present in the base from a leak, preventing the water inlet valve from filling further. The thermistor shuts off the water flow from the valve if the incoming water temperature is outside of the acceptable range. Replaces Part Numbers WD21X10519, 3028650, WD21X10492, WD21X20204, PD00023214, EAP8690623, AP5781465, PS8690623. Compatibility This replacement flood  switch fits select GE, Hotpoint, and RCA dishwashers. Example compatible models include (but are not limited to): GE GSD2100V65BB, GDF520PGJ2WW, Hotpoint HDA3600H35BB, and RCA RBD3300G00BB. Always verify your dishwasher’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Designed to meet OEM performance and safety standards 💧 Prevents Overfilling – Accurately detects water level and stops excessive filling 💰 Budget-Friendly Alternative – Provides OEM-like reliability at a lower cost 🛠️ Quick & Easy Installation – Simple wiring connection for fast repair 🛡️ Fixes Common Issues – Solves leaking, overfilling, or dishwasher not filling problems 📐 Product Specification Part Number: WD21X10519 Component Type: Dishwasher flood Switch Material: Plastic flood housing with integrated electrical microswitch Mounting: Direct-fit installation beneath dishwasher tub Function: Monitors water level and signals control board Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, pliers (optional) ⚠️ Safety First: Always unplug the dishwasher or turn off its circuit breaker before servicing. Steps: Disconnect power to the dishwasher. Remove the toe-kick panel to access the flood  switch area. Disconnect the wiring connector from the old switch. Twist or unclip the old flood switch and remove it. Install the new XPARTCO WD21X10519 switch in the same position. Reconnect wiring, reinstall toe-kick panel, and restore power. Run a quick fill test to confirm proper operation. ⏱️ Time Required: 10–15 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Protect your dishwasher from overfilling — Add to Cart Now for a reliable, cost-effective repair!

Read more less

XPARTCO 3390719 Dryer Thermal Fuse – Replaces WP3390719 – Compatible with Whirlpool, Maytag & Kenmore Dryers Product Description Restore safe dryer operation and proper heating with the XPARTCO 3390719 Dryer Thermal Fuse. This dryer Thermal Fuse is a replacement part for specific Whirlpool, Kenmore dryer models. This disposable, one-time fuse ensures safe operation of your appliance by cutting off power if the temperature exceeds safe limits. A bad thermal fuse can cause your appliance to stop functioning or prevent it from turning on altogether. Symptoms of a bad thermal fuse include no heat or a dryer that won't start. It is located on the blower housing and cannot be reset. XPARTCO is a trusted aftermarket brand offering appliance replacement parts built to OEM-equivalent specifications at a cost-effective price. Replaces Part Numbers WP3390719, 3390719, 15-198, 279650, 3389639, 3389640, 660877, 688841, 690198, 690798, 80004, ET402, G4AP0401, PD00002330, EAP11741444, AP6008309, PS11741444. Compatibility This replacement dryer thermal fuse fits select Whirlpool, Maytag, Kenmore, Amana, Estate, Roper, and Crosley dryers. Commonly installed on the blower housing or exhaust duct, depending on model. Always verify your dryer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM safety and temperature ratings 🛡️ Overheat Protection – Shuts off power if unsafe temperatures are detected 🔥 Fixes No-Heat or No-Run Issues – Common solution for blown fuse symptoms 🧩 Direct-Fit Design – Installs easily without modification 💰 Cost-Effective Repair – Reliable alternative to OEM thermal fuses 📐 Product Specification Part Number: 3390719 Component Type: Dryer Thermal Fuse Function: One-time over-temperature safety cutoff Application: Blower housing or exhaust system Mounting: Screw-mounted Quality Level: Aftermarket replacement (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver ⚠️ Safety First: Unplug the dryer before servicing to avoid electrical shock. Basic Steps: Disconnect dryer power. Remove the rear or front access panel (model dependent). Locate the thermal fuse on the blower housing or exhaust duct. Disconnect wires and remove the old fuse. Install the new XPARTCO 3390719 thermal fuse. Reconnect wiring, reassemble panels, and restore power. Test dryer operation. ⏱️ Time Required: 15–20 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Aftermarket Appliance Parts 🔄 30-Day Return Policy Restore dryer safety and reliable operation — Add to Cart Now for a dependable, budget-friendly repair!

Read more less

XPARTCO 4681JB1029B Refrigerator Condenser Fan Motor 13Vdc, 1.55W, 120mA, CCW. Fits specific LG refrigerator models. Replaces Part Numbers: 4681JB1029B, 4681JB1017B, 4681JB1017E, 4681JB1027B, AP4437343, OEM17749374, PS3523329. Description: This Condenser Fan Motor is a replacement part for specific LG, Kenmore refrigerator models. This motor is responsible for powering the fan that cools the condenser coils, which helps dissipate heat from the refrigerator. Proper functioning of the condenser fan motor is crucial for maintaining the efficiency and cooling performance of the refrigerator.   This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less