Dryer Door Latches, Switches & Knobs

XPARTCO WE01X25316 Dryer Door Catch The XPARTCO WE01X25316 is an aftermarket replacement dryer door catch (also called a door latch) compatible with a wide range of GE and Hotpoint electric and gas dryers in the GTD, GTX, ETD, HTX, NTX, PTD, and YTD series. The door catch is the spring-loaded latch mechanism mounted inside the dryer door panel that snaps onto the door strike on the dryer cabinet when the door is closed, holding the door securely shut during operation and activating the door switch so the dryer can run. When the catch breaks or loses its spring tension, the door will not stay closed, the dryer will not start, or the door will pop open during a drying cycle. This replacement catch is constructed from toughened nylon with a hardened manganese steel spring — materials chosen for superior wear resistance and spring durability compared to standard nylon. It is sold individually and mounts inside the dryer door panel using a snap-in clip retained by a metal retaining ring. Installation requires partially disassembling the dryer door to access the catch from the inside. It directly replaces 4512762, AP6037347, EAP11766999, PD00042653, and PS11766999. Installs in 15–30 minutes with basic tools. Quick Answer The XPARTCO WE01X25316 Dryer Door Catch fixes GE and Hotpoint dryers where the door won't stay closed, pops open mid-cycle, or won't activate the door switch to start. Toughened nylon body with manganese steel spring. Sold individually. Mounts inside the door panel — door must be partially disassembled for installation. Compatible with GE GTD3–GTD8, GTX, ETD, HTX, NTX, PTD, and YTD series dryers. Replaces 4512762, AP6037347, EAP11766999, PD00042653, PS11766999. Common Problems This Part Fixes Dryer door will not stay closed during the drying cycle Door pops open mid-cycle, stopping the dryer Dryer will not start — door switch not being activated by worn or broken catch Door feels loose or does not click firmly when closed Door catch visibly cracked, broken, or spring missing Door requires being held or pushed closed to keep the dryer running Replaces Part Numbers This door catch directly replaces the following OEM and cross-reference part numbers: WE01X25316, 4512762, AGE24874, AP6037347, EAP11766999, PD00042653, PS11766999 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This door catch is compatible with select GE and Hotpoint gas and electric dryers from the following series: GE dryers — GTD3, GTD4, GTD5, GTD6, GTD7, GTD8 series (GTD33EASK0WW, GTD42EASJ1WW, GTD58EBSV0WS, GTD65EBPL0DG, GTD72EBSN0WS, GTD75ECPL0DG, GTD84ECPN0DG and related models) GE dryers — GTX2, GTX3, GTX4, GTX6 series (GTX22EASK0WW, GTX33EASK0WW and related models) GE dryers — ETD48 series (ETD48GASW0WB and related models) GE dryers — PTD6, PTD7, PTD9 series (PTD60EBPR1DG and related models) GE dryers — YTD7 series (YTD74E2PN2DG and related models) GE dryers — XTD series (XTD72E8ST1WS and related models) Hotpoint dryers — HTX2, HTX24 series (HTX21EASK0WW, HTX24EASK0WW, HTX24GASK0WS and related models) Hotpoint dryers — NTX6 series (NTX62E8ST0WW and related models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Holds the dryer door closed and activates the door switch so the dryer can run safely Toughened nylon body — superior wear resistance compared to standard nylon catches Hardened manganese steel spring — provides reliable, durable spring tension for thousands of open/close cycles Snap-in design — mounts inside the door panel with a metal retaining clip Replaces 4512762, AP6037347, EAP11766999, and PS11766999 Sold individually — one door catch per order Compatible with GE GTD, GTX, ETD, HTX, NTX, PTD, and YTD series dryers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number WE01X25316 Part Type Dryer Door Catch (Door Latch) Condition Aftermarket Replacement Application GE and Hotpoint Gas and Electric Dryers Material Toughened nylon / Hardened manganese steel spring Mounting Snap-in inside the door panel — metal retaining clip secures in place Sold As Single door catch Compatible Brands GE, Hotpoint Installation Notes ⚠️ Unplug Dryer Before Starting — Door Disassembly Required Unplug the dryer before beginning. Unlike simpler snap-in door catches, the WE01X25316 is mounted inside the dryer door panel and requires partially disassembling the door to access it. Open the dryer door and remove the screws on the latch side of the door (typically three screws) and the screws on the hinge side (typically five screws). Gently pry the door inner and outer panels apart — work carefully around the edge. With the panels separated, locate the old catch — use pliers to squeeze the gray retaining tabs together and push downward to release the catch from the inner panel. With needle-nose pliers, squeeze the metal retaining clip and apply downward force until the clip is free. Insert the new WE01X25316 catch into the panel opening and snap it into place, then press the retaining clip back on to lock it. Reassemble the door panels and reinstall all screws. Close the door to confirm it latches firmly. Restore power and run a short cycle to verify normal operation. Tools needed: drill driver with 1/4" bit, #1 square head bit, pliers, needle-nose pliers. Frequently Asked Questions Why does installation require disassembling the door? Unlike the snap-in door catches found on many Whirlpool-family dryers — which clip into a slot accessible from the front without disassembly — the WE01X25316 mounts inside the GE door panel between the inner and outer door skins. This is a GE-specific design that provides a cleaner door exterior but requires separating the two door panels to access and replace the catch. While it is more involved than a simple snap-in replacement, it is a well-documented DIY repair that most homeowners can complete in 15–30 minutes with the right tools. My dryer door closes but the dryer still won't start — is it the catch? It may be — a worn or cracked catch may not push far enough into the door strike to fully activate the door switch, even if the door appears closed. However, if the catch appears intact and snaps firmly onto the strike, the issue may be with the door switch itself rather than the catch. The door switch (located inside the dryer cabinet at the door opening) can be tested with a multimeter for continuity in the open and closed positions. If the switch tests open in both positions, it has failed and needs replacement independently of the door catch. Is this compatible with older GE dryers that have a different door catch style? The WE01X25316 is for newer GE GTD, GTX, HTX, and related series dryers. Older GE dryers used a different door catch kit — most notably the WE01X1158 / WE1M536 / WE1M1011 style, which is a separate catch and strike kit. If your GE dryer is an older model not in the GTD/GTX/HTX series listed above, verify your model number before ordering to confirm this is the correct catch for your dryer. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured from toughened nylon with a hardened manganese steel spring to match the dimensions and function of the original WE01X25316 door catch. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

279570 Genuine OEM Whirlpool Dryer Door Catch Kit The 279570 is a Genuine OEM Whirlpool dryer door catch and strike kit compatible with a wide range of Whirlpool, Kenmore, Roper, Estate, Amana, Crosley, Inglis, KitchenAid, Maytag, and Admiral dryers. The door catch is the spring-clip mechanism on the dryer door that snaps over the door strike to hold the door firmly closed during operation, activating the door switch so the dryer can run. When the catch breaks, wears out, or loses tension, the door will not stay closed, the door switch will not be activated, and the dryer will either not start or will stop mid-cycle. The strike is the corresponding post or tab on the dryer cabinet that the catch engages. This Genuine OEM kit includes three color-coded door catches of different tensions and two metal door strikes, plus one screw. Because the tension of the catch must match the original, Whirlpool includes three options in the kit — each is color-coded and numbered on the back. Refer to identify which catch is correct for your model. The kit directly replaces a very large list of older cross-reference numbers including 279570VP, 3493, 2003, 8208, 279280, 279337, 696144, 693717, AP3094183, PS334230, and dozens more. Installs in under 15 minutes with a Phillips screwdriver. Quick Answer The 279570 Genuine OEM Whirlpool Dryer Door Catch Kit fixes dryers where the door won't stay closed, pops open mid-cycle, or won't activate the door switch to start. Kit includes 3 color-coded catches (different tensions), 2 metal strikes, 1 screw. Use the catch that matches your original. Genuine OEM. Compatible with Whirlpool, Kenmore, Roper, Estate, Amana, Crosley, Inglis, KitchenAid, Maytag, and Admiral dryers. Installs in under 15 minutes. Common Problems This Kit Fixes Dryer door will not stay closed during the drying cycle Door pops open mid-cycle, stopping the dryer Dryer will not start — door switch not being activated by a worn or broken catch Door feels loose or does not click shut firmly when closed Door catch visibly cracked, broken, or missing Door strike bent or missing — door cannot engage the catch properly Dryer requires the door to be held or pushed closed to stay running Replaces Part Numbers This door catch kit directly replaces the following OEM and cross-reference part numbers: 279570, 14205029, 14205577, 14210022, 2003, 236876, 236877, 241282, 241890, 26000279570, 261847, 263067, 279280, 279337, 279469, 279570VP, 291949, 3390239, 3392538, 3398175, 342295, 347813, 3493, 4165234, 51651001, 51655001, 66021, 690081, 690082, 693717, 694343, 696144, 8208, 830751, 834767, 834813, 834943, 834944, AH334230, DE902, EA334230, EAP334230, FSP279570, AP3094183, AWP39897, PD00002346, PS334230. Contact our support team with your model number if you need confirmation before ordering. Compatibility This door catch kit is compatible with select dryers from the following brands: Whirlpool dryers (gas and electric) Kenmore / Sears dryers (Whirlpool-built models) Roper dryers Estate dryers Amana dryers Crosley dryers Inglis dryers KitchenAid dryers Maytag dryers Admiral dryers Important: This kit includes three catches with different spring tensions, color-coded and numbered on the back. You must use the catch that matches the tension of your original. Using the wrong tension catch may result in a door that is too hard to open or too easy to pop open. Key Features Genuine OEM kit manufactured by Whirlpool to factory specifications — guaranteed fit and performance Holds the dryer door closed and activates the door switch so the dryer can run safely Kit includes 3 color-coded door catches (different spring tensions), 2 metal door strikes, 1 screw Catches are color-coded and numbered on the back — use the one that matches your original. Plastic catches with metal strikes and metal screw — durable construction for long service life Consolidates a very large list of older Whirlpool-family door catch cross-reference numbers Compatible with 10 major appliance brands on the Whirlpool platform Quick DIY repair — installs in under 15 minutes with a Phillips screwdriver Product Specifications Part Number 279570 Part Type Dryer Door Catch and Strike Kit Condition Genuine OEM Application Gas and Electric Dryers Kit Includes 3 color-coded door catches (different tensions), 2 metal strikes, 1 screw Material Plastic catches / Metal strikes Color White / Silver Catch Selection Color-coded and numbered, Use the catch that matches your original Compatible Brands Whirlpool, Kenmore, Roper, Estate, Amana, Crosley, Inglis, KitchenAid, Maytag, Admiral Installation Notes ⚠️ Unplug Dryer Before Starting Disconnect power before beginning. using the wrong tension catch will result in incorrect door resistance. Open the dryer door and locate the old door catch on the inside of the door panel and the strike on the dryer cabinet opening. To remove the old catch: press the retaining tabs and pull the catch free from its slot, or unscrew the mounting screw. Install the correct new catch into the same position. To replace the strike: remove the old strike (typically held by a single screw) and install the new strike in the same position. Close the dryer door to confirm it latches firmly with a satisfying click. Restore power and run a short test cycle to confirm the door stays closed and the dryer operates normally. Tools needed: Phillips screwdriver; needle-nose pliers may help with catch removal on some models. Frequently Asked Questions Why does the kit include three different catches? Whirlpool used door catches with different spring tensions across its dryer lineup — a lighter catch on some models and a stiffer catch on others. To cover all compatible models in a single kit, Whirlpool includes three catches of different tensions, each color-coded and numbered on the back. It is important to use the correct one — using a catch with too little tension may allow the door to pop open, while a catch with too much tension may make the door difficult to open. Do I need to replace both the catch and the strike, or just one? It depends on which component has failed. The catch (the spring-clip on the door) is the more commonly replaced part — it wears out from repeated use faster than the strike. Inspect both: if the catch is cracked or has lost its spring tension, replace the catch. If the strike is bent, cracked, or missing, replace the strike. Since the kit includes both catches and strikes, you have everything needed for a complete repair. When in doubt, replacing both ensures the full latch system is renewed. My dryer will not start even after replacing the door catch — what else could it be? If the dryer still will not start after the catch is replaced, the door switch may also need to be tested. The door switch is the electrical component that the door catch activates when the door closes — if the switch itself is failed, replacing the catch alone will not restore function. Test the door switch (3406105 for most Whirlpool-family models) with a multimeter for continuity in both the open and closed positions. If the switch reads open in both positions or closed in both positions, it has failed and needs replacement. How is the 279570 different from the W11429587 dryer door catch? The 279570 is the door catch kit for older Whirlpool-family dryers — it includes multiple catches of different tensions and metal strikes because it covers a wide range of older models. The W11429587 is a single snap-in door catch for newer Whirlpool-family dryers (Cabrio and newer platform models). If your dryer is a newer model with a snap-in catch slot rather than a screw-mounted catch and strike, you likely need the W11429587. Verify your model number to confirm which part is correct. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM kit manufactured by Whirlpool to factory specifications. It is the exact same door catch and strike kit supplied by Whirlpool for compatible dryer service repairs — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 3406105 Dryer Door Switch Replaces WP3406105 The XPARTCO 3406105 is an aftermarket replacement dryer door switch assembly compatible with a wide range of Whirlpool-family dryers including Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Estate, Crosley, Inglis, Admiral, Jenn-Air, Magic Chef, and Norge. The door switch is a safety component mounted inside the dryer cabinet near the door opening. When the door is closed, the door strike depresses the switch actuator, completing the circuit and allowing the dryer to start and run. When the door is opened, the switch opens the circuit and stops the dryer. On models with a broken belt detection circuit, the door switch also plays a role in belt failure detection. A failed door switch causes the dryer to either not start at all or to run continuously with the door open. This is a Single Pole, Double Throw (SPDT) 3-wire switch with stainless steel terminals and a heat-resistant housing. It measures 1-3/4" L x 1-5/8" W x 1-1/4" H with a 7-3/4" wiring harness. Electrical specs are 120-240V, 50-60Hz, 11A, 1/3HP. The kit includes the switch and 3-wire harness assembly. It directly replaces WP3406105, 3406104, 3405104, 3405105, 528947, AP6008560, and several additional cross-reference numbers. Installs in 15–30 minutes with basic hand tools. Quick Answer The XPARTCO 3406105 Dryer Door Switch fixes Whirlpool-family dryers that won't start, won't stop when the door is opened, or require the door to be slammed to start. SPDT 3-wire switch, 120-240V/50-60Hz/11A/1/3HP. Body 1-3/4" L x 1-5/8" W x 1-1/4" H, 7-3/4" harness. Includes switch and harness assembly. Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, and more. Replaces WP3406105, 3406104, 3405104, 528947, AP6008560. Common Problems This Part Fixes Dryer will not start at all — door switch not completing the circuit when door is closed Dryer starts only when the door is slammed or held firmly closed Dryer continues to run after the door is opened — switch not opening the circuit Drum light not turning on when the door is opened (on models with drum light) Dryer starts intermittently — door switch contact worn and making unreliable contact Dryer stops mid-cycle randomly — switch opening the circuit due to vibration or wear Door switch visibly cracked, broken, or the actuator button no longer springs back Replaces Part Numbers This door switch directly replaces the following OEM and cross-reference part numbers: WP3406105, 3405104, 3405105, 3406104, 3406105, WP3406105VP, AWP47182, PD00003898, EAP11741700, AP6008560, PS11741700. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This door switch is compatible with select gas and electric dryers from the following brands: Whirlpool dryers (gas and electric) Kenmore / Sears dryers (Whirlpool-built models) Maytag dryers (gas and electric) KitchenAid dryers Amana dryers Roper dryers Estate dryers Crosley dryers Inglis dryers Admiral dryers Jenn-Air dryers Magic Chef dryers Norge dryers Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Safety switch — prevents dryer from operating when the door is open and stops the dryer immediately when the door is opened mid-cycle Single Pole, Double Throw (SPDT) 3-wire switch — provides both normally-open and normally-closed contacts for dryer start circuit and belt failure detection on compatible models Rated 120-240V, 50-60Hz, 11A, 1/3HP — correct electrical specifications for compatible Whirlpool-family dryers Switch body: 1-3/4" L x 1-5/8" W x 1-1/4" H; wiring harness: 7-3/4" L Stainless steel terminals and heat-resistant housing Kit includes switch and 3-wire harness assembly — complete plug-in replacement Replaces WP3406105, 3406104, 3405104, 3405105, 528947, and AP6008560 Compatible with 13 major appliance brands on the Whirlpool platform Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in 15–30 minutes with basic hand tools Product Specifications Part Number 3406105 OEM Part Number WP3406105 Part Type Dryer Door Switch Assembly (SPDT 3-Wire) Condition Aftermarket Replacement Application Gas and Electric Dryers Switch Type Single Pole, Double Throw (SPDT) Wires 3-wire Voltage 120-240V Frequency 50-60Hz Amperage 11A Horsepower 1/3 HP Switch Body Dimensions 1-3/4" L x 1-5/8" W x 1-1/4" H Harness Length 7-3/4 inches Color Off-White / Black / Gray Material Plastic / Metal (stainless steel terminals) Includes Switch and 3-wire harness assembly Compatible Brands Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Estate, Crosley, Inglis, Admiral, Jenn-Air, Magic Chef, Norge Installation Notes ⚠️ Unplug Dryer Before Starting Disconnect power (and shut off gas for gas dryers) before beginning. The door switch is located inside the dryer cabinet near the door opening, typically mounted in the front panel or top panel. Access it by inserting a putty knife under the top panel to release the spring clips and lift the top, then release the front panel. Locate the old door switch — it is a small rectangular component with a spring-loaded actuator button. Photograph the wiring connections before disconnecting. Disconnect the 3-wire harness from the old switch. Release the switch from its mounting bracket by pressing the retaining tabs and pulling the switch free, or unscrewing the mounting screw. Snap the new 3406105 switch into the mounting bracket and reconnect the 3-wire harness in the same positions. Reassemble the front and top panels, restore power, and run a test cycle to confirm the dryer starts, stops when the door is opened, and runs normally. Tools needed: Phillips screwdriver, putty knife. Frequently Asked Questions What does the dryer door switch do? The door switch is a safety component that monitors whether the dryer door is open or closed. When the door is closed, the door strike depresses the switch actuator, completing the electrical circuit and signaling the control board that it is safe to run. When the door is opened, the actuator releases, opening the circuit and stopping the dryer immediately. On many Whirlpool-family dryers, the 3-wire SPDT switch also provides a secondary circuit used for broken belt detection — one of the switch's contacts is part of the motor start circuit, while the other is part of a safety cutoff circuit. How do I test the door switch with a multimeter? Unplug the dryer and disconnect the switch from the harness. Set your multimeter to continuity mode. The 3406105 is an SPDT switch with three terminals — typically labeled Common (C), Normally Open (NO), and Normally Closed (NC). With the actuator button not pressed (door open position), you should read continuity between C and NC, and no continuity between C and NO. With the actuator button pressed (door closed position), you should read continuity between C and NO, and no continuity between C and NC. Any deviation from this pattern confirms the switch has failed. What is the difference between 3406105 and 3406104? The 3406104 was the original part number, and the 3406105 (later updated to WP3406105) is the current replacement that superseded it. They are the same door switch and are fully interchangeable. The 3405104 and 3405105 are also cross-references for this same switch from earlier production. If your dryer's documentation or old switch label shows any of these numbers, the 3406105 is the correct current replacement. Why does this switch have 3 wires when my old switch only had 2? The WP3406105 is an SPDT (Single Pole, Double Throw) switch with 3 terminals — Common, Normally Open, and Normally Closed. Some older dryer models used a simpler 2-wire switch, but the 3-wire WP3406105 is the updated replacement that works on both older and newer models. On models that originally had a 2-wire switch, only two of the three terminals are used — the third is simply left unconnected. Follow your model's wiring diagram or take a photo of the original switch's wire connections before removing it. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured from durable plastic and metal with stainless steel terminals to match the dimensions and electrical specifications of the original WP3406105 door switch assembly. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

WE01X24552 Genuine OEM Dryer Timer Knob - Compatible with GE Dryers Product Description Restore your dryer’s functionality with the WE01X24552 Genuine OEM Dryer Timer Knob from Parts-O-Matic. This high-quality, original GE-manufactured replacement timer knob is designed for select GE dryer models, enabling precise control of timer settings for cycle duration and drying programs. Crafted from durable, impact-resistant plastic with a secure D-shaped stem, it ensures a reliable fit for worn, cracked, or missing timer knobs. Note: Always disconnect power before installation. Verify model compatibility with your dryer. Replaces Part Numbers: WE01X24552, 4396547, AP6026722, AGE25750, EAP11736611, OEM18080175, PD00041231, PS11736611. Compatibility Compatible with GE dryer models, including but not limited to: GTD42EASJWW GTD65EBSJWS GTD33EASKWW GTX42EASJWW Verify your model number using the dryer’s manual or contact Parts-O-Matic support for assistance. Key Features ✅ Genuine OEM Part: Original GE-manufactured timer knob for guaranteed compatibility and quality. ✅ Brand Compatibility: Specifically designed for select GE dryer models. 🔥 Specifications: Made of durable plastic, D-shaped stem, matte white or chrome finish (color may vary), dimensions approximately 2.5" diameter x 1.2" height. 💰 Cost-Effective: Offers OEM performance at a competitive price. 🛠️ Easy Installation: Tool-free installation, completes in 2–5 minutes. 🛡️ Reliable Fixes: Resolves issues with broken, stripped, or non-functional timer knobs. Installation Instructions Safety First: Unplug the dryer from the power source to prevent electrical hazards. Gently pull the old timer knob straight off the control shaft. Use a flathead screwdriver to pry if needed, but avoid excessive force. Align the WE01X24552 timer knob’s D-shaped stem with the control shaft and push firmly until secure. Test the timer knob by turning it to confirm proper engagement with dryer timer settings. Estimated Time: 2–5 minutes Product Specifications Material: High-impact plastic Color: Matte white or chrome (varies by model) Dimensions: 2.5" diameter x 1.2" height (approximate) Weight: 0.5 oz Stem Type: D-shaped for secure fit SKU: REP-WE01X24552

Read more less

XPARTCO WE04X24719 Dryer Start Button – Compatible with GE Dryers Product Description Restore dependable operation with the WE04X24719 Dryer Start Button. This replacement button allows you to start and control drying cycles. A worn, cracked, or unresponsive button can prevent the dryer from starting or make operation difficult. Replacing it with this replacement button ensures smooth function and reliable performance. Replaces Part Numbers WE04X24719, PD00046802, AP6034220, 4587500, PS11766637. Compatibility This start button is compatible with select GE dryers. Example compatible models include (but are not limited to): GE GTD42EASJ2WW, GE GTD65EBSJ3WS, and GE GTD45EASJ2WS. Always verify your dryer’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Reliable Replacement – Reliable aftermarket replacement for GE dryer start button 🔘 Reliable Operation – Restores start functionality for dryer cycles 💰 Cost-Effective Fix – Affordable way to replace a worn or broken button 🛠️ Quick Installation – Installs in minutes with basic tools 🛡️ Fixes Common Issues – Resolves unresponsive, cracked, or missing start button problems 📐 Product Specification Part Number: XPWE04X24719 Component Type: Dryer Start Button Material: Durable plastic construction Mounting: Snap-in design, direct replacement Operating Conditions: Residential dryer use 🛠️ Installation Notes Tools Needed: Phillips screwdriver, flathead screwdriver (if needed) ⚠️ Safety First: Always unplug dryer before starting repairs to avoid electrical shock. Steps: Unplug dryer and locate control panel. Remove panel screws to access start button assembly. Release old button from mounting clips. Insert new WE04X24719 button into slot until it clicks securely. Reassemble control panel and restore power. Test dryer to ensure button works correctly. ⏱️ Time Required: 10–15 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders 🛠️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Fix your dryer start function today — Add to Cart Now for a genuine, factory-approved repair!

Read more less

🚪 XPARTCO 131658800 Dryer Door Catch This Door Catch is a replacement part for specific Kenmore, Frigidaire dryer models. It includes the door catch. This part ensures the dryer door remains securely closed during operation, preventing heat loss and ensuring the appliance functions efficiently. Common causes of a bad door catch include regular wear and tear, physical damage, or misalignment of the door, which can impact the catch's ability to latch properly. Fix a loose or non-latching dryer door with this aftermarket replacement for part number 131658800. This dryer door catch holds the dryer door securely closed during operation to ensure proper airflow and drying performance. Designed to fit many Frigidaire, Kenmore, Electrolux, and Crosley dryers. ✅ Key Features: High-quality aftermarket replacement for part #131658800 Made from durable plastic for long-lasting use Designed to securely latch the door shut Simple snap-in installation — no tools required Helps prevent cycle interruption due to door opening 🔁 Replaces OEM Part Numbers: 131658800, 131658820, 131658845, 00634863, 07521419, 08015370, 134548000, 134548045, 3004967, 3202755, 3281055, 5303281055, 5307521419, 7521419, 835, AH418433, EA418433, F141735-000, F141735000, F62661-4, K1300884, K1301594, K1308079, K1309301, N8010215, Q0000401002, Q000504551, Q000504553, Q504551, Q504553, WQ504551, WQ504553, AP2107362, PS418433, WE01X25316, AP6037347, 4512762, PS11766999. ⚠️ Common Symptoms Fixed: Dryer door won’t stay closed Dryer won’t start due to open door switch Door pops open during a cycle Visible wear or damage to original catch 🧰 Compatible Brands: ✔️ Frigidaire✔️ Electrolux✔️ Kenmore (Frigidaire-built)✔️ Gibson✔️ Tappan✔️ Crosley✔️ White-Westinghouse 📌 Need help verifying compatibility? Send us your dryer’s model number — we’ll check it for you. 🚚 Why Buy from Parts-O-Matic? ✅ Reliable aftermarket performance ✅ Always Fast and Free U.S. shipping ✅ Easy DIY repair with trusted support ✅ Backed by excellent customer service 🛒 Fix your dryer’s latching issue today — order the 131658800 dryer door catch from Parts-O-Matic.com, and enjoy fast, free U.S. shipping!

Read more less

ERP 3406108 Dryer Door Switch  Replaces Part Numbers: WP3406108, 3406108, PS11741702, AP6008562  Description: This Door Switch is a replacement part for select Whirlpool dryer models. It is responsible for detecting whether the dryer door is open or closed. When the door is closed, the switch allows the dryer to operate. Conversely, if the door is open, the switch interrupts the electrical circuit to prevent the dryer from running, ensuring safety during use. Fits Models:   LTE5243DQ1 , LTE5243DQ2 , LTE5243DQ3 , LTE5243DQ4 , LTE5243DQ5 , LTE5243DQ6 , LTE5243DQ7 , LTE5243DQ8 , LTE5243DQ9 , LTE5243DQA , LTE5243DQB , LTE5243DT2 , LTE5243DT3 , LTE5243DT4 , LTE5243DT5 , LTE5243DT6 , LTE5243DT7 , LTE5243DZ1 , LTE5243DZ2 , LTG5243DQ1 , LTG5243DQ2 , LTG5243DQ3 , LTG5243DQ4 , LTG5243DQ5 , LTG5243DQ6 , LTG5243DQ7 , LTG5243DQ8 , LTG5243DQ9 , LTG5243DQA , LTG5243DQB , LTG5243DQC , LTG5243DT2 , LTG5243DT3 , LTG5243DT4 , LTG5243DT5 , LTG5243DT6 , LTG5243DT7 , LTG5243DT8 , LTG5243DZ1 , LTG5243DZ2 , WET4024EW0 , YLTE5243DQ2 , YLTE5243DQ3 , YLTE5243DQ4 , YLTE5243DQ5 , YLTE5243DQ6 , YLTE5243DQ7 , YLTE5243DQ8 , YLTE5243DQ9 , YLTE5243DQA , YLTE5243DQB , YWET4024EW0. This is an aftermarket part that can be used as a replacement for the OEM part. 

Read more less