Drain Pumps

Choice 280187 Washer Drain Pump Assembly The Choice 280187 is an aftermarket replacement front-load washer drain pump and motor assembly compatible with a wide range of Whirlpool, Maytag, KitchenAid, Kenmore, Amana, Jenn-Air, Roper, Admiral, Norge, and Magic Chef front-load washers — including the Whirlpool Duet GHW and WFW series, Maytag Epic MFW series, Maytag MHWE and NFW series, and Kenmore HE front-load washers. The drain pump removes water from the washer tub during the drain portion of each wash cycle. When the pump fails, the washer will not drain, will leave standing water in the tub, stop mid-cycle, display error code F21, or make unusual noise during the drain phase. This complete assembly includes the Askoll M75-compatible pump motor, motor impeller, pump housing with filter, and mounting grommets. Rated 120V, 60Hz, 70W, 1.0A with a 15-minute on / 45-minute off duty cycle. Dimensions: 10-1/4"L x 6-1/4"W x 5-1/4"H. It directly replaces 285998, 8181684, 8182819, 8182821, 1200164, Askoll M75, LP280187, AP3953640, AH1485610, EA1485610, EAP1485610, PD00002352, and PS1485610. Always check and clear the pump filter/coin trap before replacing the pump — a clogged filter is among the most common causes of F21 errors. Installs in 15–30 minutes with basic hand tools. Quick Answer The Choice 280187 Washer Drain Pump Assembly fixes Whirlpool Duet, Maytag Epic, and Kenmore HE front-load washers that won't drain, leave standing water, display error code F21, or make loud humming or grinding noises during the drain cycle. Complete assembly — motor, impeller, housing, filter, and grommets. 120V/60Hz/70W/1.0A. 15 min on / 45 min off. 10-1/4"L x 6-1/4"W x 5-1/4"H. Replaces 285998, 8181684, 8182819, 8182821, 1200164, Askoll M75, AP3953640, PS1485610. Check filter before replacing pump. Common Problems This Part Fixes Washer not draining — standing water remaining in the tub after a cycle Error code F21 displayed — long drain fault (washer unable to drain within allotted time) Washer stopping mid-cycle due to a drain fault Loud humming during the drain phase — motor running but impeller not pumping Grinding or rattling noise during drain — damaged impeller or worn pump bearings Clothes excessively wet after a cycle — pump not fully removing water before spin Water draining very slowly — worn pump motor below rated performance Water leaking from the pump area at the front of the washer Replaces Part Numbers This drain pump directly replaces the following OEM and cross-reference part numbers: 280187, 1200164, 285998, 8181684, 8182819, 8182821, AH1485610, AP3953640, AWP39453, EA1485610, EAP1485610, PD00002352, PS1485610. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drain pump is compatible with select front-load washers from the following brands and series: Whirlpool front-load washers — Duet GHW series (GHW9100L, GHW9150P, GHW9160P, GHW9200L, GHW9250M, GHW9300P, GHW9400P, GHW9400SU0, GHW9460P and related models) Whirlpool front-load washers — Duet WFW series (WFW9200S, WFW9300V, WFW9400S, WFW9400V, WFW9410X and related models) Maytag front-load washers — Epic MFW series (MFW9600SQ0, MFW9600SQ1, MFW9700S, MFW9800TK0, MFW9800TQ0 and related models) Maytag front-load washers — MHWE series (MHWE300V, MHWE400W, MHWE450W, MHWE500VW, MHWE550W, MHWE950W and related models) Maytag front-load washers — NFW series (NFW7500V, NFW7600XW00 and related models) KitchenAid front-load washers — KHWS series (KHWS01PM, KHWS02R and related models) Kenmore / Sears front-load washers — HE series (select 110-series Whirlpool-built models) 7M series front-load washers (7MGHW9100MW0, 7MGHW9150, 7MGHW9400 and related models) Amana, Jenn-Air, Roper, Admiral, Norge, and Magic Chef front-load washers (select models) Important: Before replacing the pump, check and clear the pump filter/coin trap behind the lower front access panel — a clogged filter is a very common cause of F21 errors and slow draining that does not require pump replacement. Always verify your model number before ordering. Key Features Removes water from the tub during drain and spin cycles for proper washer operation Complete assembly — Askoll M75-compatible motor, impeller, pump housing with filter, mounting grommets, and hardware included Rated 120V, 60Hz, 70W, 1.0A — correct electrical specifications for compatible front-load washer models Duty cycle: 15 minutes on / 45 minutes off — matches original pump operating requirements Dimensions: 10-1/4"L x 6-1/4"W x 5-1/4"H Resolves error code F21 (long drain fault) on compatible Whirlpool Duet, Maytag Epic, and Kenmore HE models Replaces 285998, 8181684, 8182819, 8182821, 1200164, Askoll M75, AP3953640, and PS1485610 Compatible with Whirlpool GHW/WFW Duet, Maytag Epic/MHWE/NFW, KitchenAid KHWS, and Kenmore HE front-load washers Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 15–30 minutes with basic hand tools Product Specifications Part Number 280187CM Part Type Front-Load Washer Drain Pump and Motor Assembly Condition Aftermarket Replacement Application Front-Load Washers — Whirlpool Duet, Maytag Epic/MHWE/NFW, Kenmore HE Motor Askoll M75-compatible Voltage 120V AC Frequency 60 Hz Wattage 70W Amperage 1.0A Duty Cycle 15 minutes on / 45 minutes off Dimensions 10-1/4"L x 6-1/4"W x 5-1/4"H Color White / Black / Gray / Red Material Metal / Plastic Housing / Rubber Includes Pump motor, impeller, housing with filter, rear grommets, front grommets, hardware Error Code Resolved F21 (long drain fault) Compatible Brands Whirlpool, Maytag, KitchenAid, Kenmore, Amana, Jenn-Air, Roper, Admiral, Norge, Magic Chef Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off the water supply before beginning. Place towels on the floor in front of the washer — residual water will drain from the pump when it is disconnected. The drain pump is accessed from the lower front panel. Remove the screws from the lower kick panel to expose the pump access area. Before removing the pump, drain residual water by removing the pump filter cap (have a shallow pan ready). After draining, disconnect the pump wiring harness. Release the hose clamps and pull the drain hoses free from the pump ports. Unscrew the pump mounting screws or twist out the mounting grommets. Remove the old pump and install the new 280187 assembly in the same position using the included grommets. Reconnect hoses, secure clamps, and reconnect the wiring harness. Reinstall the kick panel. Restore power and water and run a drain/spin cycle to verify drainage and check for leaks. Tools needed: Phillips screwdriver, pliers, shallow pan, towels. Frequently Asked Questions What does error code F21 mean on Whirlpool Duet and Maytag front-load washers? F21 indicates a long drain fault — the washer was unable to drain within the expected time (typically 8 minutes). Before replacing the pump, check and clean the pump filter/coin trap at the lower front of the washer — lint, coins, and debris in the filter restrict flow and are a very common cause of F21 errors. If the filter is clean and the error persists, the drain pump motor has likely failed and needs replacement. What is the Askoll M75 motor and why is it referenced? The original 280187 drain pump used an Askoll M75 motor — Askoll is an Italian motor manufacturer that supplies drain pump motors to Whirlpool for use in Duet, Maytag Epic, and related front-load washers. Aftermarket replacements for the 280187 are often described as "Askoll M75 compatible" to confirm they are designed as drop-in replacements for pumps using that motor. The Choice 280187 drain pump is manufactured to match the performance specifications of the original Askoll M75-based assembly. What is the difference between 280187 and 8182821 or 8181684? These are all part numbers for the same front-load washer drain pump assembly across different production runs and naming conventions. 285998, 8181684, 8182819, and 8182821 are earlier cross-references for this pump from Whirlpool's parts catalog, and 280187 is the current consolidated part number. The 1200164 is an additional cross-reference. This aftermarket replacement covers all of them. Should I check the pump filter before replacing the pump? Yes — always check the pump filter first. On compatible Whirlpool Duet, Maytag Epic, and Kenmore HE front-load washers, the pump filter is accessible behind the lower front kick panel. Remove the cap, drain residual water into a pan, and remove any debris from the filter. If the filter was clogged and the error clears after cleaning, pump replacement is not needed. If the filter is clear and the F21 error persists, or if the pump makes loud noise or leaks, then pump replacement is required. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured with an Askoll M75-compatible motor to match the electrical specifications and performance of the original 280187 drain pump assembly. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO W11396717 Washer Drain Pump Assembly The XPARTCO W11396717 is an aftermarket replacement drain pump assembly compatible with select Whirlpool, Maytag, and Kenmore high-efficiency top-load washers — including the Whirlpool WTW5100, WTW6120, WTW7120, WTW8120, and WTW8127 series, and the Maytag MVW6200, MVW6230, MVW7230, MVW7232, and MVW8230 series. The drain pump removes water from the washer tub during the drain portion of each wash cycle. When the pump fails, the washer will not drain, will leave standing water in the tub, stop mid-cycle, or make loud humming, grinding, or rattling noises during the drain phase. Rated 120V, 60Hz, 1.2A (CL.F duty class), this complete pump assembly is mounted to the underside of the outer tub and secured by three mounting screws. It directly replaces the earlier W11263349 as well as 4960510, AP6974116, PS12731177, and EAP12731177. Note: the pump is accessed from the bottom of the washer — the machine must be tilted or laid on its back to reach the mounting screws. Installs in 20–35 minutes with basic hand tools. Quick Answer The XPARTCO W11396717 Washer Drain Pump fixes Whirlpool and Maytag HE top-load washers that won't drain, leave standing water, stop mid-cycle, or make loud noise during the drain cycle. 120V/60Hz/1.2A CL.F. Mounted on the underside of the outer tub — access by tilting the washer. Replaces W11263349, 4960510, AP6974116, PS12731177, EAP12731177. Compatible with Whirlpool WTW5100/6120/7120/8120/8127 and Maytag MVW6200/6230/7230/7232/8230 series top-load washers. Common Problems This Part Fixes Washer not draining — standing water remaining in the tub after a cycle Washer stopping mid-cycle due to a drain fault Loud humming during the drain phase — motor energized but pump not moving water Grinding or rattling during drain — damaged impeller or worn bearings Clothes excessively wet after a full cycle — pump not fully removing water before spin Water draining very slowly — pump motor weakening below rated performance Water leaking from the pump area underneath the washer Replaces Part Numbers This drain pump directly replaces the following OEM and cross-reference part numbers: W11396717, W11263349, Hanyu B25-3A04, AP6974116, AWP44690, EAP12731177, PD00065247, PS12731177 W11396717 is the current production part number superseding W11263349. If your parts diagram shows W11263349, the W11396717 is the correct current replacement. Contact our support team if you need confirmation before ordering. Compatibility This drain pump is compatible with select HE top-load washers from the following brands and series: Whirlpool top-load washers — WTW5100HC0, WTW5100HW0, WTW5105HC0, WTW5105HW0, WTW6120HC0, WTW6120HW0, WTW7120HC0, WTW7120HC1, WTW7120HW0, WTW8120HC0, WTW8120HW0, WTW8127LC1, WTW8127LW0, WTW8127LW1 and related models Maytag top-load washers — MVW6200KW0, MVW6230HC0, MVW6230HW0, MVW6230RHW0, MVW7230HC0, MVW7230HC1, MVW7230HW0, MVW7230HW1, MVW7232HC0, MVW7232HC1, MVW7232HC2, MVW7232HW0, MVW7232HW1, MVW7232HW2, MVW8230HC0, 7MMVW7230LC0, 7MMVW7230LW0 and related models Kenmore / Sears top-load washers — 11021112021, 11021652020, 11031652020 and related models Note: This pump is mounted on the underside of the outer tub and requires tilting or laying the washer on its back for access. Always verify your model number before ordering. Key Features Removes water from the tub during drain and spin cycles for proper washer operation Rated 120V, 60Hz, 1.2A (CL.F) — correct electrical specifications for compatible HE top-load washers Current production part — directly supersedes W11263349 Mounted on the underside of the outer tub and secured by three mounting screws — tilt or lay washer on its back for access Replaces W11263349, 4960510, AP6974116, PS12731177, EAP12731177, and B25-3A04 Compatible with Whirlpool WTW5100/6120/7120/8120/8127 and Maytag MVW6200/6230/7230/7232/8230 series top-load washers Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 20–35 minutes with basic hand tools Product Specifications Part Number W11396717 Supersedes W11263349 Part Type HE Top-Load Washer Drain Pump Assembly Condition Aftermarket Replacement Application Whirlpool / Maytag / Kenmore HE Top-Load Washers Voltage 120V AC Frequency 60 Hz Amperage 1.2A Duty Class CL.F Mounting 3 screws on underside of outer tub — tilt washer for access Compatible Brands Whirlpool, Maytag, Kenmore Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting — Work Gloves Recommended Disconnect power and turn off the water supply before beginning. Wear work gloves throughout. The drain pump is mounted on the underside of the outer tub — to access it, disconnect the water supply hoses, drain hose, and lid switch wiring, then carefully tilt the washer onto its back or side on a padded surface. Locate the pump on the bottom of the tub. Using a 5/16" nut driver, remove the three mounting screws securing the pump assembly to the tub. Release the two spring clamps with channel-lock pliers and disconnect the inlet and outlet hoses from the pump. Disconnect the wiring harness and remove the old pump. Install the new W11396717 pump in the same position, reconnect hoses and clamps, reconnect the wiring harness, and secure with the three mounting screws. Return the washer to upright, reconnect all hoses and wiring, restore power and water, and run a drain/spin cycle to confirm drainage and check for leaks. Tools needed: Phillips screwdriver, 5/16" nut driver, channel-lock pliers, padded surface for tilting, work gloves. Frequently Asked Questions What is the difference between W11396717 and W11263349? These are the same drain pump assembly across two production revisions. W11263349 was the original part number, and W11396717 is the current updated version that supersedes it. Whirlpool issues updated part numbers when minor engineering changes are made during production. Both are the same pump with the same specifications, dimensions, and function. If your washer's parts diagram shows W11263349, the W11396717 is the correct current replacement to order. Why does accessing this pump require tilting the washer? On compatible Whirlpool WTW and Maytag MVW HE top-load washers, the drain pump is mounted directly to the underside of the outer tub — not on the cabinet side panel or behind a front access panel as on some other models. The pump's three mounting screws are only reachable from below the machine. The standard repair procedure is to unplug and disconnect the washer, tilt it onto its back or side on a padded surface, access the pump from underneath, and return the washer to upright after installation. How do I know if it's the drain pump versus a blocked drain hose? Before replacing the pump, check the drain hose for kinks or blockages — disconnect the hose and blow through it to confirm it is clear. Also check whether the drain hose standpipe height is within the recommended range (typically 39–96 inches from the floor). If the hose is clear and properly positioned but the washer still won't drain, listen during the drain phase: a completely silent drain cycle (motor not running) suggests a failed motor or control board issue, while a humming or grinding noise during drain confirms the pump motor is receiving power but the pump is mechanically failed and needs replacement. Is this pump the same as the W10876600 used in older Whirlpool Cabrio models? No — the W11396717 and the W10876600 are different drain pumps for different Whirlpool top-load washer generations. The W10876600 (and its successor WPW10730972) is used in older Whirlpool Cabrio and Maytag Centennial models. The W11396717 is used in newer WTW5100/6120/7120/8120 and MVW6200/6230/7230/7232/8230 series models. They are not interchangeable — verify your model number before ordering. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the electrical specifications and performance of the original W11396717 drain pump assembly. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO W10876600 Washer Drain Pump – Compatible with Whirlpool, Maytag, Amana, and Crosley Washers Product Description Restore reliable draining performance with the XPARTCO W10876600 Washer Drain Pump. This washer drain pump moves water out of the washer during drain and spin. Replacing a worn or failed pump restores proper draining so cycles finish on time and the basket can reach full spin speed. Replacing it with this durable pump ensures smooth water removal and dependable washer operation at a fraction of the OEM cost. Replaces Part Numbers W10876600, 4455877, W10727777, W10876600VP, PD00034529, EAP11738156, AP6004933, PS11738156. Compatibility This replacement drain pump fits select Whirlpool, Maytag, Amana, and Crosley top-load and front-load washers. Example compatible models include (but are not limited to): Whirlpool WTW5000DW1, Maytag MVWC565FW0, and Amana NTW4516FW3. Always verify your washer’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Designed to meet OEM performance standards 💧 Efficient Water Removal – Pumps out water quickly and quietly during drain cycles 💰 Budget-Friendly Solution – High-quality alternative to expensive OEM parts 🛠️ DIY Installation – Plug-and-play design for easy home repair 🛡️ Fixes Common Issues – Solves washer not draining, “F9E1” or “SD” error codes, and standing water problems 📐 Product Specification Part Number: W10876600 Component Type: Washer Drain Pump Assembly Material: Reinforced plastic housing with electric motor Voltage: 120V AC Mounting: Direct-fit replacement on washer base Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Nut driver, pliers, towel or bucket ⚠️ Safety First: Always unplug the washer and disconnect water supply before performing any repairs to prevent electrical shock or leaks. Steps: Disconnect power and water hoses. Tilt the washer back or remove the front access panel. Disconnect the wiring harness and hose clamps. Remove the old drain pump and install the new W10876600 pump. Reconnect hoses and wiring, secure the pump, and reassemble the panel. Restore power and run a drain or rinse cycle to confirm proper operation. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Fix washer drainage issues quickly — Add to Cart Now for a reliable, budget-friendly repair!

Read more less

XPARTCO EAU64082901 Washer Drain Pump Motor – for AHA75693425 – Compatible with LG & Kenmore Washers Product Description Restore proper draining and reliable washer operation with the XPARTCO EAU64082901 Washer Drain Pump Motor. This high-quality replacement pumps water out of the washer tub during drain and spin cycles. A failing drain pump motor can cause water not draining, standing water, slow spin cycles, or drain error codes. Replacing it with this dependable XPARTCO pump motor ensures efficient water removal and smooth washer performance. Replaces Part Numbers EAU64082901, PD00090792, AP6336279. EAP12750085. Replacement Motor for Drain pump Assembly for AHA75693425, PD00068706, EAP12750085, AP6978815, PS12750085 Compatibility This replacement washer drain pump motor fits select LG and Kenmore (LG-manufactured) front-load and top-load washers. Example compatible models include (but are not limited to):LG WM2277HW, WM2455HW, WM3470HWAKenmore 796.40272900, 796.41472210 Always verify your washer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Designed to match OEM flow rate and electrical performance 💧 Efficient Water Drainage – Removes water quickly during drain and spin cycles 🔇 Quiet Operation – Smooth motor design minimizes noise and vibration 💪 Durable Construction – Built for long service life in wet environments 🛡️ Fixes Common Issues – Solves washer not draining, water left in tub, or drain error codes 📐 Product Specification Part Number: EAU64082901 Component Type: Washer Drain Pump Motor only Voltage: 26V Mounting: Direct-fit pump housing installation Connection: Electrical terminals with hose ports Application: Drain and spin water removal Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, pliers, towel or shallow pan ⚠️ Safety First: Unplug the washer and turn off water supply before servicing. Steps: Disconnect power and water supply. Access the drain pump from the front or bottom panel. Place a towel to catch residual water. Disconnect hoses and wiring from the old pump motor. Install the new XPARTCO EAU64082901 pump motor. Reconnect hoses and wiring, reassemble panels, and restore power. Run a test drain cycle to confirm proper operation. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Restore proper washer draining and avoid costly water issues — Add to Cart Now for a reliable, budget-friendly repair!

Read more less

XPARTCO DC97-19289F Washer Drain Pump Assembly The XPARTCO DC97-19289F is an aftermarket replacement washer drain pump assembly compatible with a wide range of Samsung top-load washers in the WA40, WA41, WA42, WA44, WA45, WA48, WA50, WA52, and WA54 series, as well as select Kenmore models built on the Samsung platform. The drain pump removes water from the washer tub during the drain portion of each wash cycle. When the pump fails, the washer will display error codes 5C, SE, nd, 5E, FO2, or E5, leave standing water in the tub, stop mid-cycle, or produce unusual noise during draining. This complete drain pump assembly is rated 120V, 60Hz, 80W, 1.1A with a 30-minute on / 30-minute off duty cycle. It directly replaces DC97-19289A, DC97-19289B, DC97-17349B, DC97-17366A, DC97-17366J, and PX3516-01. Note: the wire plug on the new pump may differ slightly from the original — if the connector does not match your washer's harness, transfer the wiring harness from the old pump to the new one. Installs in 20–30 minutes with basic hand tools. Quick Answer The XPARTCO DC97-19289F Washer Drain Pump Assembly fixes Samsung top-load washers displaying error codes 5C, SE, nd, 5E, FO2, or E5, not draining, leaving standing water, or making loud noise during the drain cycle. 120V/60Hz/80W/1.1A, 30 min on/30 min off duty cycle. Compatible with Samsung WA40 through WA54 series and Kenmore (Samsung-built). Replaces DC97-19289A, DC97-19289B, DC97-17349B, DC97-17366A, DC97-17366J, PX3516-01. Note: if wire plug differs, transfer harness from old pump. Common Problems This Part Fixes Error codes 5C, SE, nd, 5E, FO2, or E5 — washer cannot drain within the allotted time Washer not draining — standing water remaining in the tub after a cycle Washer stopping mid-cycle due to a drain fault Loud humming, grinding, or rattling noise during the drain cycle Water draining very slowly — worn pump motor below rated performance Water leaking from the drain pump area at the bottom of the washer Pump running continuously but water not being expelled from the tub Replaces Part Numbers This drain pump directly replaces the following OEM and cross-reference part numbers: DC97-19289F, DC97-17349B, DC97-19289B,DC97-17366A, DC97-17366J, DC97-19289A,ASM772133, AP6806651, EAP12592631, PD00049911, PX3516-01, PS12592631. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drain pump is compatible with select top-load washers from the following brands and series: Samsung top-load washers — WA40 series (WA400PJHDWR and related models) Samsung top-load washers — WA41 series (WA41A3000AW and related models) Samsung top-load washers — WA42 series Samsung top-load washers — WA44 series (WA44A3205AW and related models) Samsung top-load washers — WA45 series (WA45H7000AW, WA45M7050AW, WA45N3050AW, WA45T3200AW and related models) Samsung top-load washers — WA48 series (WA48H7400AW and related models) Samsung top-load washers — WA50 series (WA50F9A7DSP, WA50M7450AW and related models) Samsung top-load washers — WA52 series (WA52M7750AW, WA52M8650AW and related models) Samsung top-load washers — WA54 series (WA54M8750AV and related models) Samsung top-load washers — WA456DRHDSU series Kenmore / Sears top-load washers (select Samsung-built models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Removes water from the tub during the drain and spin cycles for proper washer operation Resolves Samsung error codes 5C, SE, nd, 5E, FO2, and E5 caused by drain pump failure Rated 120V, 60Hz, 80W, 1.1A — correct electrical specifications for compatible Samsung top-load models 30-minute on / 30-minute off duty cycle — matches the operational requirements of compatible models Replaces DC97-19289A, DC97-19289B, DC97-17349B, DC97-17366A, DC97-17366J, and PX3516-01 Wire plug may differ from original — transfer harness from old pump if connector does not match Compatible with Samsung WA40 through WA54 series and Kenmore Samsung-built top-load washers Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 20–30 minutes with basic hand tools Product Specifications Part Number DC97-19289F Also Replaces DC97-19289A, DC97-19289B (prior versions) Part Type Washer Drain Pump Assembly Condition Aftermarket Replacement Application Samsung Top-Load Washers Voltage 120V AC Frequency 60 Hz Wattage 80W Amperage 1.1A Duty Cycle 30 minutes on / 30 minutes off Error Codes Resolved 5C, SE, nd, 5E, FO2, E5 Connector Note Wire plug may differ — transfer harness from old pump if needed Compatible Brands Samsung, Kenmore (Samsung-built) Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off the water supply before beginning. Tilt the washer back or lay it on its side to access the drain pump at the bottom of the machine. Place towels and a shallow pan to catch residual water when the pump is disconnected. Note the wiring connector orientation before disconnecting — take a photo if needed. If the new pump's connector does not match the washer's harness, carefully transfer the wiring harness from the old pump to the new pump. Disconnect the drain hoses from the pump using pliers to loosen the clamps. Unscrew the pump mounting screws and remove the old pump. Install the new DC97-19289F pump in the same position, reconnect drain hoses and secure with clamps, and reconnect the wiring harness. Restore water supply and power, then run a drain cycle to verify proper drainage and check for leaks. Tools needed: Phillips screwdriver, pliers, shallow pan, towels. Frequently Asked Questions What error codes indicate a drain pump failure on Samsung washers? Error codes 5C, SE, nd, 5E, FO2, and E5 on Samsung top-load washers all indicate a drain fault — the washer was unable to drain within the expected time. These codes can also be caused by a clogged drain filter, blocked hose, or kinked drain line, so check those first. If the filter and hose are clear and the error persists after clearing them, the drain pump is the most likely cause. What is the difference between DC97-19289F, DC97-19289A, and DC97-19289B? These are successive revisions of the same Samsung drain pump assembly. DC97-19289A was the original version, DC97-19289B was an update, and DC97-19289F is the current version. Samsung issues revised part numbers when minor production changes are made — all three perform the same function and the DC97-19289F is the correct current replacement for any of the earlier versions. The DC97-17349B, DC97-17366A, and DC97-17366J are additional older cross-references for this pump used on earlier Samsung top-load models. Why might the wire plug on the new pump differ from the original? Samsung revised the wiring connector on this drain pump across different production runs. If the DC97-19289F pump you receive has a different connector than your washer's harness, do not force the connection. Instead, carefully remove the wiring harness from the old pump and transfer it to the new pump — both versions use the same internal terminals and the harness swap is straightforward. This is a known and documented step for this part and does not affect performance or safety. Should I check the drain filter before replacing the pump? Yes — always check and clean the drain filter and inspect the drain hose for kinks or blockages before replacing the pump. A clogged filter or blocked hose can cause the same error codes as a failed pump and clearing the blockage may resolve the problem without needing a new part. On Samsung top-load washers the drain filter is typically located at the bottom front of the machine. If the filter and hose are clear and the error persists, the pump needs replacement. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured to match the electrical specifications and performance of the original DC97-19289F drain pump assembly. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 137311900 Washer Drain Pump Assembly – Compatible with Frigidaire & Electrolux Washers Product Description Restore proper water drainage and dependable washer operation with the XPARTCO 137311900 Washer Drain Pump Assembly. This high-quality aftermarket replacement pump is designed to efficiently remove water during drain and spin cycles. A worn or failing drain pump can cause standing water, slow draining, error codes, or loud humming noises. Replacing it with this reliable XPARTCO pump helps return your washer to smooth, consistent performance at a budget-friendly price. XPARTCO aftermarket parts are engineered to match original fit and function while offering a cost-effective alternative to OE or Genuine OEM components. Replaces Part Numbers 137311900, 2688889, PD00006068, EAP3655041, AP5630474, PS3655041. Compatibility This replacement washer drain pump assembly fits select Frigidaire, Electrolux, Crosley, Gibson, and Kenmore (Frigidaire-manufactured) washers. Example compatible models include (but are not limited to): Frigidaire FAFW3577KW0, FFTW4120SW Electrolux EIFLW55HIW0 Always verify your washer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM fit and pumping performance 💧 Efficient Water Removal – Restores proper draining during cycles 🔇 Quiet, Smooth Operation – Helps eliminate humming or grinding noises 💪 Durable Motor & Housing – Built for reliable long-term use 💰 Cost-Effective Repair – Affordable alternative to OE and OEM pumps 📐 Product Specification Part Number: 137311900 Component Type: Washer Drain Pump Assembly Voltage: 120V AC Mounting: Direct-fit, bolt-on installation Application: Washer drain and spin system Quality Level: Aftermarket replacement (not OE / not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver, pliers ⚠️ Safety First: Unplug the washer and shut off the water supply before servicing. Basic Steps: Disconnect washer power and water supply. Access the drain pump from the bottom or rear of the washer. Remove hoses and electrical connectors. Remove mounting screws and take out the old pump. Install the new XPARTCO 137311900 drain pump assembly. Reconnect hoses and wiring, reassemble panels, and restore power. Run a test cycle to confirm proper draining. ⏱️ Time Required: 25–35 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Aftermarket Appliance Parts 🔄 30-Day Return Policy Fix drainage issues and get your washer running smoothly again — Add to Cart Now for a dependable, budget-friendly repair!

Read more less

WPW10409079 Washer Genuine OEM Drain Pump Replaces Part Number: WPW10409079, W10409079, 2118648, AP6021043, PS11754363, LP09079. Description: This Drain Pump is a replacement part for specific Whirlpool top-loading washing machine models. Located near the bottom center of the machine, it actively pumps water out of the washer tub at the end of each cycle.  The pump motor spins an impeller chamber to push water through the drain hose and out of the home. Causes of failure include clogging from mineral buildup or fabric fibers within the pumping components. Over time, motor windings experience excess heat and may burn out from consistent drainage cycles. WPW10409079 is the part number for a Whirlpool washer drain pump that removes water from the washer during the drain cycle. It is compatible with many Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef models.

Read more less

WH23X10040 Washer Drain Pump – Genuine OEM for GE Washers The Drain Pump is a Genuine OEM part for select GE washing machine models that is responsible for removing water from the washer at the end of the wash cycle. The pump forces water out through the drain hose so that clothing comes out free of excess water, making the drying process faster.  Whether your washer is not draining, displaying error codes, or stopping mid-cycle, this original replacement pump restores full functionality and performance. ✅ Key Features: Genuine OEM part – WH23X10040 Direct fit for many GE, Hotpoint, and RCA washers Quiet and energy-efficient operation Built to factory specifications for reliability and performance Includes pump motor and housing assembly 120V, 85W, 60Hz. 🔁 Replaces Part Numbers: WH23X10040, 2216538, 228C89P001, AH3501453, EA3501453, AP5306354, PS3501453. ⚠️ Fixes These Common Washer Problems: Washer not draining properly Standing water left after spin cycle Error codes related to pump failure Washer won’t complete the cycle Loud or buzzing noise from the drain pump 🧰 Compatible Models: 36361532110 GTUN275GM1WW GTUP240EM0WW GTUP240EM1WW GTUP240EM2WW GTUP240EM3WW GTUP240EM4WW GTUP240EM5WW GTUP240EM6WW GTUP240GM0WW GTUP240GM1WW GTUP240GM2WW GTUP240GM3WW GTUP240GM4WW GTUP240GM5WW GTUP240GM6WW GTUP270EM0WW GTUP270EM1WW GTUP270EM2WW GTUP270EM3WW GTUP270GM1WW GTUP270GM2WW GTUP270GM3WW GTUP270GM4WW GTUP270GM5WW GUD27GSSJ0WW 36361542 36361542211 36361542310 36361542410 36361542411 36371532110 36371542 36371542211 36371542310 36371542410 36361532412 GTUN275GM0WW GTUN275GM2WW GTUP270EM4WW GTUP270EM5WW GTUP270GM0WW GUD24ESSJ0WW GUD24GSSJ0WW 26715321 2671532110 2671532210 2671532211 2671532212 2671532311 2671532312 2671532412 2671532413 GTUN275EM0WW GTUN275EM1WW GTUN275EM2WW 2661532412 2661532210 2661532110 2661532211 2661532212 2661532311 2661532312 2661532413 2661532513 363.6153241 GUD27ESSJ1WW GUD27ESSM0WW GUV27ESSM0WW GUD27GSSM0WW GUD27GSSM1WW GUD27ESPM0DG GUD27GSPM0DG GUD27ESPM1DG GUD27GSSJ1WW GUD27GSPM1DG GUV27ESSM1WW GUD27EESN0WW GUD27GESN0WW GUD27ESSM1WW GUD27GSSM2WW GUD27ESSJ0WW 🧰 Compatible With: ✔️ GE✔️ Hotpoint✔️ RCA (by GE)(Check your washer’s model number to ensure fit — or contact us for support.) 🚚 Why Buy from Parts-O-Matic? ✅ 100% Genuine OEM part – no cheap imitations ✅ Always Fast and Free U.S. shipping ✅ Competitive pricing with professional support ✅ Trusted by technicians and DIYers nationwide 🛒 Get your washer draining like new again — order the WH23X10040 Genuine GE Drain Pump today at Parts-O-Matic.com, and enjoy fast, free delivery across the U.S.

Read more less

W11458345 Genuine OEM Washer Drain Pump - Compatible with Whirlpool, Maytag, Amana Product Description Restore your washer’s performance with the W11458345 Genuine OEM Washer Drain Pump. This Whirlpool-manufactured pump is designed as a replacement for select Whirlpool, Maytag, Amana, Inglis, and Kenmore washing machines. It efficiently drains wastewater during wash cycles and includes a large filter that can be cleaned monthly with Washing Machine Cleaner Tablets. This part addresses issues like water not draining, loud buzzing or grinding noises, or failure to enter agitation cycles, often caused by blockages, wear, or pump motor failure. Note: Includes (1) drain pump assembly. Disconnect power before installation. Verify compatibility with your washer model. Replaces part numbers: W11458345, W11316609, W10918608, W11319789, PD00062450, EAP16218041, AP6989186, PS16218041. Compatibility: Compatible with select washer models, including but not limited to: Whirlpool: WFW862CHC3, WFW6620HW1, WFW6620HW2, WFW9620HC2, 8TWFW8620HW1 Maytag: MHW5630HW1, MHW5630HW3, 7MWFW5622HW2 Amana: NFW5800HW0 Kenmore: 110.42932200 Inglis: IFW5900HW0 Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Whirlpool, Maytag, Amana, Inglis, and Kenmore washers. 🔧 Specifications: Genuine OEM Whirlpool drain pump, 120V, stainless steel construction. 💪 Reliable Performance: Efficiently drains wastewater for optimal washer operation. 🛠️ Easy Installation: Requires screwdriver, pliers, and nut driver; typically installed in 30–60 minutes. 🛡️ Effective Fixes: Resolves water not draining, buzzing/grinding noises, or agitation cycle issues. Product Specification Part Number: W11458345 Component Type: Washer drain pump assembly Material: Stainless steel and plastic (Based on web:0, web:1, web:2, web:3, web:4, web:5, web:6, web:7, web:8, web:9, web:10, web:11, web:12, web:13, web:14, web:15) Dimensions: Approximately 9.75" L x 9.5" W x 5.25" H (Based on web:0) Weight: 3.32 lbs (Based on web:0) Electrical Specs: 120V, submersible design (Based on web:0, web:2) Compliance: UL-listed, Prop 65 warning for California (Based on web:0, web:1, web:2, web:3, web:4, web:5, web:6, web:7, web:8, web:9, web:10, web:11, web:12, web:13, web:14, web:15) Installation Notes: Safety First: Disconnect the washer from the power source before installation. Shop for high-quality appliance parts with a 30-day return policy. Keep your washer running smoothly today! Add to cart now for a reliable fix!

Read more less

W11399437 Genuine OEM Washer Drain Pump Replaces Part Numbers: AP6974144, PS12731241 Description: This Drain Pump is a Genuine OEM part for select Maytag, Kenmore, Whirlpool washer models. It is responsible for circulating water through the washing machine during all cycles. The pump draws water from the tub and dispenses it through the water supply hoses to soak, scrub, and rinse clothes.  

Read more less

W10919003 Washer Genuine OEM Drain Pump Replaces Part Numbers: W10919003, 4461359, W10775446, AP6038235, PS11770076. Description: This Water Pump is a Genuine OEM replacement part for specific Maytag, Kenmore, Whirlpool washing machine models. It plays a crucial role in circulating water throughout the wash cycles and draining the used water from the tub.

Read more less

8182415 Washer Genuine OEM Drain Pump Fits Specific Whirlpool, Maytag washer Models. Replaces Part Numbers: WP8182415, 8182415, OEM24047170, AP6011792, 1065543, PS11744991. Description: This Drain Pump is a Genuine OEM part for specific Whirlpool, Maytag, Kenmore washing machine models.    California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less