Dryer replacement parts

Genuine GE OEM Dryer Part GE WE12X10014 Dryer Genuine OEM Drum Belt 87-inch, 4-rib drum drive belt for select GE, Hotpoint, RCA and Kenmore dryers. Product Overview The GE WE12X10014 Dryer Genuine OEM Drum Belt connects the dryer motor pulley to the drum so the drum can rotate during the drying cycle. This genuine GE replacement belt is designed for compatible GE, Hotpoint, RCA, and select Kenmore dryers that use the common 87-inch, 4-rib drive belt. Quick Answer WE12X10014 is an approximately 87 inch long × 1/4 inch wide dryer belt with 4 ribs/ridges. It replaces several earlier GE belt numbers including WE12X42 and WE12X82. Common Problems This Part May Fix Dryer drum does not turn Motor runs but drum stays still Belt is broken, stretched, glazed, or frayed Squealing or slapping noise from a damaged belt Dryer will not tumble properly Replaces and Cross-References WE12X10014, 103C7487, 1472898, WE12X0042, WE12X0082, WE12X42, WE12X42-, WE12X42P, WE12X42R, WE12X82, WE12X82E, WE12X82P, WE12X82R, 132C7487P004, AH2350043, EA2350043, PD00000990, EAP2350043, AGE25021, AP4379804, PS2350043 Cross-reference numbers are provided for identification. This listing is for Genuine GE OEM part WE12X10014. Compatibility Fits select GE, Hotpoint, RCA and Kenmore dryers. Compatible model examples include: DCLR333ET0WW DBLR333ET0WW DBLR333GT0WW NVLR333ET0WB NVLR333GT0WB DVLR223ET0WW DDE7200SBLWW DDE7500GAL DLB3400SBLWH DWLR473ET0WW NLLR113ET1WO DDG7688MCL Important: This is only a partial compatibility list. Verify the complete dryer model number and original belt part number before ordering. Key Features Genuine GE OEM replacement part Approx. 87 inches long Approx. 1/4 inch wide 4-rib / 4-ridge drive surface Transfers motor power to dryer drum Fits many GE-built dryer platforms Product Specifications Manufacturer Part Number WE12X10014 Brand GE Genuine OEM Part Type Dryer Drum Drive Belt Length Approx. 87 in. Width Approx. 1/4 in. Ribs / Ridges 4 Condition New Part Quality Genuine OEM Package Quantity 1 Belt Installation Notes Unplug the dryer before service. Access the drum and release belt tension from the idler pulley. Remove the old belt and inspect the idler pulley and motor pulley for wear or debris. Install the new belt with the ribbed side against the drum where specified by the dryer design. Route the belt around the motor pulley and idler exactly as shown in the appliance service diagram. Rotate the drum by hand to confirm smooth tracking before reassembly. Diagnostic tip: A broken belt can result from a seized idler pulley, worn drum bearing/glides, or an obstructed drum. Inspect related components before installing the new belt. Frequently Asked Questions How long is WE12X10014? It is approximately 87 inches long and 1/4 inch wide. How many ribs does this belt have? It has 4 ribs/ridges on the drive surface. Does it replace WE12X42 and WE12X82? Yes. WE12X10014 is commonly listed as the replacement for those earlier belt numbers. Is this a Genuine GE OEM belt? Yes. This listing is for Genuine GE OEM part WE12X10014. Shop With Confidence Verify the complete dryer model number before ordering. Our compatibility team can help confirm whether Genuine GE OEM WE12X10014 is correct for your dryer. Genuine GE OEM87 Inch Belt4-Rib DesignCompatibility Support

Read more less

XPARTCO 37001298 Dryer Drum Front Glide Replaces Part Numbers: WP37001298, 37001298, 1166078, 40116501, 40116502, 5-1553, 5-1676, 501553, 501676, 503452, WP37001298VP, Y501676, AP6008790, PS11741931. Teflon glide for front support Fits specific model Amana and Speed Queen dryers Description: This Dryer Drum Glide is a replacement part for specific Maytag, Amana, Speed Queen, Whirlpool dryer models. It is designed to facilitate smooth rotation and movement of the dryer drum during operation. The glide supports the drum, reducing friction and ensuring proper alignment. Common causes of a bad dryer drum glide can include wear and tear over time, exposure to excessive heat or vibration, or damage from foreign objects or improper installation.   This is an aftermarket part that can be used as a replacement for the OEM part. 

Read more less

XPARTCO WE4M160 Dryer High Limit Thermostat The XPARTCO WE4M160 is an aftermarket replacement high limit (safety) thermostat for GE, Hotpoint, and Kenmore dryers, and for some Fisher & Paykel dryers. This safety thermostat is part of the dryer's heating circuit. It shuts off power to the heating element when the dryer gets too hot, which protects the dryer from overheating. GE catalogs the original as the "Thermostat Safety Left." This is a direct-fit aftermarket replacement for the original GE thermostat. If a high limit thermostat trips or fails, it is worth checking the cause of the overheating at the same time. A clogged lint trap or restricted exhaust vent is a common culprit. Quick Answer The XPARTCO WE4M160 High Limit Thermostat replaces the safety thermostat on a GE, Hotpoint, or Kenmore dryer that overheats, shuts off during the heat cycle, or won't heat because the thermostat has opened or failed. Classic symptom: the dryer gets too hot or quits on heat, and a vent check shows the airflow is clear. Common Problems This Part Fixes Dryer runs too hot Dryer shuts off the heat during a cycle Dryer runs but doesn't heat because the safety thermostat has opened Dryer won't start if the thermostat has failed open Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This thermostat directly replaces the following part numbers: WE4M160, WE04M0160, L210-30F, AGE25640, AP2042573, AH267911, EA267911, EAP267911, PD00008081, PS267911 These numbers span generations of GE's own part numbering for this thermostat. Confirm against your dryer's parts diagram, or contact our support team, if your model calls out a different number. Compatibility This thermostat is listed for GE, Hotpoint, and Kenmore dryers and for some Fisher & Paykel dryers, including these examples: GE DBLR333EE0CC, DBSR453EA0WW, DBXR453EA0AA, DBXR463EB0CC GE DPXR475EW0WW, DPSF505GW0WW, DCCB330ED0WC Model numbers 61140418, 62160T3WB Fisher & Paykel DE70FA1-96971, DE60FA2-96983 Note: The models above are a small sample of a list of hundreds, not a full list. GE sells more than one safety thermostat for its dryers, including the WE4M137, so check your model number against your dryer's parts diagram, or contact our support team to verify fit before ordering. Key Features Direct-fit aftermarket high limit (safety) thermostat for GE-built dryers Shuts off power to the heating element when the dryer overheats Replaces GE WE4M160 and the older WE04M0160 Listed for GE, Hotpoint, Kenmore, and some Fisher & Paykel dryers Product Specifications Part Number XPWE4M160 OEM Part Number WE4M160 Part Type Dryer High Limit (Safety) Thermostat Condition Aftermarket Replacement Application GE, Hotpoint, Kenmore & Some Fisher & Paykel Dryers Installation Notes ⚠️ Unplug Power Before Installing Unplug the dryer before beginning, and shut off the gas supply first on gas models. Wear work gloves to protect your hands. Follow your model's service guide to reach the thermostat, note the wire positions before disconnecting them, and fit the new thermostat in the same position. Before closing the dryer, clean the lint trap and check the exhaust vent for restrictions, since poor airflow is a common cause of overheating. Frequently Asked Questions My dryer is running too hot. Is this the part I need? This thermostat is designed to cut power to the heating element when the dryer overheats, and a failed one can cause heating problems. Clear the lint trap and exhaust vent first, since restricted airflow is a common cause of overheating. Is this the same as the WE4M137 high limit thermostat? They are different GE part numbers, so don't assume they are interchangeable. Check your model number against your parts diagram, or contact our support team, before ordering. Is WE4M160 the same as WE04M0160? Yes. WE04M0160 is the older GE number for this thermostat, and WE4M160 is the current number. This thermostat replaces both. Will this fit my dryer? It is listed for hundreds of GE, Hotpoint, Kenmore, and some Fisher & Paykel dryers, but the model list above is only a sample. Check your model number against your parts diagram, or contact our support team and we'll verify it before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

306508CM Dryer Front Glide Kit Includes rivets and cushion. Fits specific Maytag dryer models. Replaces Part Numbers: 306508, 1309, 3-12941, 3-6508, 306508VP, 312941, AH1804752, DE747, EA1804752, K35-603, AP4037304, PS1804752. Description: This Tumbler Bearing Kit is a replacement part for specific Maytag, Amana, Whirlpool dryer models. It includes multiple replacement glides that support the movement of the tub. As it rotates during the cycle, the tub experiences friction that the bearings help manage.   This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

ERP W10167627 Dryer Thermal Cutoff     Replaces Part Numbers: WPW10167627, AP6016109, PS11749393, W10167627.   This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

4400EL2001F Genuine LG Dryer Drum Belt Replaces Part Numbers: 4400EL2001A, 4400EL2001C, 4400EL2001E, AP5972814, PS11705916   

Read more less

XPARTCO WE01X10125 Dryer Front Drum Slide Replaces Part Numbers: WE01X10125, WE1X10125, 943784, AH264441, EA264441, AP3669448, PS264441. Description: This Dryer Drum Glide is a replacement part for specific GE dryer models. It is designed to facilitate smooth rotation and movement of the dryer drum during operation. The glide supports the drum, reducing friction and ensuring proper alignment.   This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

ERP W10185981 Dryer Timer – Replaces WPW10185981 – Compatible with Whirlpool, Kenmore, Maytag, Estate, and Roper Dryers Product Description Restore accurate dryer cycle timing with the ERP W10185981 Dryer Timer. This high-quality replacement controls the duration of drying, auto-sense, and cooldown cycles. It is responsible for controlling and managing the timing and sequence of the various drying cycles and functions. A failing timer may cause the dryer to stop mid-cycle, run too long, not start, or remain stuck on one setting. Replacing it with this reliable ERP timer ensures smooth, consistent cycle operation at a cost-effective price. Replaces Part Numbers WPW10185981, W10185981, 1481704, 418-095-20-B5, PD00004725, EAP11749830, AP6016540, PS11749830. Compatibility This replacement dryer timer fits select Whirlpool, Kenmore, Maytag, Amana, Estate, Roper, and Crosley dryers. Example compatible models include (but are not limited to):Whirlpool WED5300SQ0, Kenmore 110.65132411, Maytag MEDC200XW1, Estate EED4400WQ0. Always verify your dryer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Designed to match OEM timing accuracy and electrical performance ⏱️ Restores Cycle Control – Regulates drying, auto-sense, and cooldown cycles 💰 Cost-Effective Alternative – Reliable performance without OEM pricing 🛠️ Direct-Fit Installation – Plug-in wiring harness and standard mounting 🛡️ Fixes Common Issues – Solves timer not advancing, dryer not starting, or cycles running too long 📐 Product Specification Part Number: W10185981 Component Type: Dryer Cycle Timer Material: Reinforced polymer housing with internal metal timing mechanism Mounting: Installs behind control panel Electrical Rating: Matches OEM specifications Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Nut driver, Phillips screwdriver ⚠️ Safety First: Always unplug the dryer before performing repairs to prevent electrical shock. Steps: Disconnect power and remove the rear control panel cover. Unplug the wiring harness from the old timer. Remove mounting screws and take out the old timer. Install the new ERP W10185981 timer in the same orientation. Reconnect wiring, reinstall the panel, and restore power. Test dryer cycles for proper operation. ⏱️ Time Required: 10–20 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Restore accurate dryer timing — Add to Cart Now for a dependable, budget-friendly repair!

Read more less

XPWE9X105 Dryer Front Lower Felt Replaces Part Numbers:WE9X105, 277130, AH268338, AP2043044, EA268338, PS268338, WE09X0105   This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

XPARTCO WE4X750 Gas Dryer Igniter The XPARTCO WE4X750 is an aftermarket replacement flat igniter for select GE, Hotpoint, Whirlpool, Maytag, Frigidaire and other gas dryers, replacing GE part WE4X750 and cross-referencing 5303937186 and 4391996. The igniter sits in the burner assembly. It heats up when electrical current passes through it and lights the gas so the dryer can heat. When it wears out or stops glowing, the dryer may run but not heat. Check your model number before ordering, as gas dryers use several different igniters. Quick Answer The XPARTCO WE4X750 Gas Dryer Igniter replaces a worn or non-glowing igniter on a compatible gas dryer from GE, Hotpoint, Whirlpool, Maytag, Frigidaire and other brands. Replaces WE4X750, WE04X0750, 5303937186 and 4391996. Classic symptom: the dryer runs but does not heat, and the igniter doesn't glow. Other parts can cause the same symptom. Common Problems This Part Fixes Gas dryer not heating Igniter not glowing Worn igniter that no longer lights the burner Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer igniter directly replaces the following part numbers: WE4X750, WE04X0750, 276846, AGE25807, AH268196, AP2042796, EA268196, PD00001123, PS268196, 5303937186, 08001685, 08010845, 08015456, 1036069, 3281151, 5303281151, 8001685, F000134211, F134211-000, F134211000, F139743-000, F139743000, G139743-000, AFR17339, AH900236, AP3674313, EA900236, PD00000539, PS900236, Q000622141, Q622141, WQ622141, 4391996, 14211282, 3-4970, 3018, 304970, 41-311, 41-590, 4391996VP, AH373025, AP3109449, AWP39344, DE351, DE363, EA373025, K35-166, K35-455, PD00002514, PS373025 Gas dryers use several different igniters, and they are not interchangeable by number alone. If your old igniter shows a different number, contact our support team and we'll check whether it matches. Compatibility This igniter is listed for select GE, Hotpoint, Whirlpool, Maytag, Frigidaire and other gas dryers. Example GE and Hotpoint models that use WE4X750: GE DBL333GA0CC, DCL333GA0AA, DVL223GA0WW, DBL333GY0WW GE DCB330GB0KC, DCD330GY1AC, DH43GW0WW Hotpoint NVL333GY0AA Note: The models above are a small sample of the roughly 36 that retailers list for WE4X750, not a full list, and the example models are GE and Hotpoint. For other brands, confirm fit by your igniter's part number (such as 4391996 or 5303937186) and your model. Check your full model number against your parts diagram, or contact our support team to verify fit before ordering. Key Features Aftermarket replacement for the GE WE4X750 flat gas dryer igniter Lights the gas burner so the dryer can heat Installs in the dryer burner assembly Replaces the earlier GE number WE04X0750 and cross-references 5303937186 and 4391996 Product Specifications Part Number XPWE4X750 OEM Part Number WE4X750, 5303937186, 4391996 Part Type Gas Dryer Igniter (Flat) Condition Aftermarket Replacement Quantity 1 Igniter Application Select GE, Hotpoint, Whirlpool, Maytag, Frigidaire & Other Gas Dryers Installation Notes ⚠️ Disconnect Power And Shut Off The Gas Before Installing Unplug the dryer and shut off the gas supply before you begin, and wear work gloves. Remove the panel to reach the burner assembly, note how the igniter and its wiring connect, and remove the old igniter. Handle the new igniter carefully and install it in the same position. Reconnect the wiring, restore power and gas, and test the dryer. If you smell gas at any point, stop and contact a qualified technician. Frequently Asked Questions My gas dryer runs but doesn't heat. Is this the part I need? It can be, if the igniter has worn out and no longer glows. Other parts, such as the gas valve coils or thermal fuse, can cause the same symptom, so confirm the igniter is the problem before replacing it. Is this an OEM or aftermarket part? This is an aftermarket replacement from XPARTCO, made to replace GE part WE4X750. If you specifically need a genuine GE part, contact our support team. Can I use a different gas dryer igniter? Not by number alone. Gas dryers use several different igniters. Match the part number and your model number, or contact our support team and we'll check for you. Will this fit my dryer? It is listed for select gas dryers from GE, Hotpoint, Whirlpool, Maytag, Frigidaire and other brands, but the model list above is only a sample. Check your full model number against your parts diagram, or contact our support team and we'll verify it before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

EXP652 Dryer Belt and Idler Pulley Replaces WPW10112954, 279640 The EXP652 is an aftermarket replacement drum belt and idler pulley kit for Whirlpool and Maytag electric and gas dryers, and also fits select KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models. These two components work together: the drum belt circles the drum and attaches to the motor pulley to transmit rotation, while the idler pulley rides against the belt to maintain proper tension so it doesn't slip or sag during operation. Because these two parts share the same drive path and tend to wear on a similar timeline, they're commonly sold and replaced together. Symptoms of failure include the dryer not starting, the drum not tumbling or spinning, and noise issues such as squealing or rubbing during operation. It directly replaces W10112954, WPW10112954, AP6015116, PS11748388 (drum belt), and AP3094197, PS334244, 279640, and 3388674 (idler pulley). Quick Answer The EXP652 Dryer Belt and Idler Pulley fixes Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore electric and gas dryers that won't start, won't tumble or spin, or make squealing/rubbing noise. Includes drum belt and idler pulley. Replaces W10112954, WPW10112954, AP6015116, PS11748388, AP3094197, PS334244, 279640, 3388674. These two parts wear together — replacing both at once, rather than just the one that failed, helps avoid reopening the dryer again soon after. What's In The Kit Component Replaces Function Drum Belt WPW10112954 / W10112954 Circles the drum and attaches to the motor pulley to transmit rotation and keep the drum tumbling. Idler Pulley 279640 Rides against the belt to maintain proper tension so it doesn't slip or sag. Common Problems This Kit Fixes Dryer won't start Drum won't tumble or spin Squealing or rubbing noise during operation Belt slipping or sagging, causing inconsistent tumbling Extended or inconsistent drying times Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer belt and idler pulley kit directly replaces the following OEM and cross-reference part numbers: Belt Replaces Part Numbers WPW10112954, W10112954, 1447719, AP6015116, AWP48873, EAP11748388, PD00003553, PS11748388 Idler Pulley Replaces Part Numbers 279640, 279640VP, 2958, 3388672, 697692, TJ279640, W10468057, AH334244, EA334244, ER279640, AWP39098, PD00002356, EAP334244, AP3094197, PS334244. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This kit is compatible with select Whirlpool electric and gas dryers, and also fits select Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore dryers built on the Whirlpool platform, including model numbers such as MED8000AG0, MED8000AW0, MGD6000XW0, MGD6000XW1, MGD6000XW2, MGD8000AG0, MGD8000AG1, MGD8000AW0, MGD8000AW1, 4KMEDC300BW0, 7MMGD0100TQ1, and MGD5500FC0. Note: Whirlpool also uses a different idler pulley, W10837240, on other dryer models — this kit specifically pairs the WPW10112954 belt with the 279640 idler pulley. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement kit — drum belt and idler pulley in one purchase Resolves "won't start," "won't tumble or spin," and "squealing/rubbing noise" symptoms Restores smooth drum rotation with proper belt tracking and tension Reduces noise and vibration from a worn belt or pulley Direct drop-in replacement matching the original belt length and pulley mounting Replaces W10112954, WPW10112954, AP6015116, PS11748388, AP3094197, PS334244, 279640, and 3388674 Compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore electric and gas dryers Built to OEM-equivalent quality standards Product Specifications Part Number EXP652 Set Contents 1x Drum Belt (replaces WPW10112954), 1x Idler Pulley (replaces 279640) Condition Aftermarket Replacement Application Whirlpool / Maytag Electric and Gas Dryers Belt Length Approx. 92-1/2" Belt Profile Flat, 5 ribs, 4 grooves Related Idler Pulley W10837240 (for other models, sold separately) Repair Difficulty Moderate — front/top panel and drum removal required Compatible Brands Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore Installation Notes ⚠️ Unplug Dryer Before Starting — This Is A Bigger Repair Requiring Significant Disassembly Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Remove the top and front panels of the dryer, then the drum, to access the belt and idler pulley. Remove the old drum belt from around the drum and motor pulley. Remove the old idler pulley from its mounting bracket. Install the new EXP652 idler pulley in the same position, making sure it spins freely by hand before continuing. Route and install the new drum belt correctly around the drum and motor pulley, matching the original path exactly, and re-tension it through the idler pulley. Reinstall the drum, then reassemble the front and top panels. Restore power and run a test cycle to confirm quiet, smooth operation with the drum tumbling normally and no squealing or rubbing noise. Tools needed: nut driver, Phillips screwdriver, work gloves. Frequently Asked Questions My dryer's motor runs but the drum won't turn. Is this the right kit? Yes, this is the classic symptom addressed by a worn or broken drum belt, and since the idler pulley works together with the belt to maintain proper tension, replacing both at once addresses the most common causes of this problem in one repair. Do I need to replace both parts, or just the one that failed? You can replace just the failed component if you've confirmed which one is actually bad, but these two parts share the same drive path and tend to wear out around the same time — a worn pulley can accelerate belt wear, and a worn belt puts extra strain on the pulley. Replacing both together, since you'll already have the dryer largely disassembled for access, helps avoid a second teardown soon after. Is this the same idler pulley as your other Whirlpool dryer belt kits? Not necessarily — Whirlpool uses more than one idler pulley design across its dryer lineup. This kit specifically pairs the WPW10112954 belt with the 279640 idler pulley. Other kits may pair the same belt with a different pulley, such as W10837240, used on other models. Always confirm your full model number before ordering. Is this an OEM or aftermarket part? This is an aftermarket replacement kit built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the belt length, rib pattern, and pulley design of the original WPW10112954 belt and 279640 idler pulley used in compatible Whirlpool, Maytag, and related electric and gas dryers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less