Dryer replacement parts

XPARTCO 8066184 Dryer Motor Pulley Replaces WP8066184 The XPARTCO 8066184 is an aftermarket replacement dryer motor pulley compatible with a wide range of Whirlpool-family dryers including Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Crosley, Estate, Inglis, Admiral, and Magic Chef. The motor pulley is a small but critical metal component that threads onto the dryer motor shaft and serves as the anchor point for the drive belt. As the motor spins, the belt wraps around the motor pulley to transfer rotation to the drum via the idler pulley. When the motor pulley cracks, strips, or breaks, the belt loses its anchor point on the motor side — the drum stops spinning even though the motor continues to run. Made from durable metal, this motor pulley measures 1-1/8" L x 1-3/8" W x 1-1/8" H and is designated Pulley 29 (60Hz). It threads onto the motor shaft with a left-hand (reverse) thread — it tightens clockwise and loosens counter-clockwise. It directly replaces WP8066184, 8578565, 3389627, 3394341, 3401143, 694871, W10299847, W10290525, W10290531, W10402909, and WP8066184VP. Installs in 30–45 minutes with basic hand tools including a wrench. Quick Answer The XPARTCO 8066184 Dryer Motor Pulley fixes Whirlpool-family dryers where the drum is not spinning, the motor runs but the belt slips off the motor shaft, or the pulley is visibly cracked or broken. Metal, 1-1/8" L x 1-3/8" W x 1-1/8" H. Left-hand thread — loosen counter-clockwise. Replaces WP8066184, 8578565, 3394341, 694871, W10299847, and more. Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Crosley, Estate, Inglis, Admiral, and Magic Chef dryers. Common Problems This Part Fixes Dryer drum not spinning — motor runs but drum is still Drive belt repeatedly slipping off the motor shaft — pulley is damaged or missing Squealing or grinding noise from the motor area during the drying cycle Motor pulley visibly cracked, stripped, or broken into pieces Belt falls off immediately after being reinstalled — pulley not gripping correctly Drum spinning intermittently due to a pulley that is partially damaged Replaces Part Numbers This motor pulley directly replaces the following OEM and cross-reference part numbers: WP8066184, 8066184, 8578565, W10299847, 1200324, 3389627, 3394341, 3401143, 694871, W10290525, W10290531, W10402909, AWP48528, AP6011686, EAP11744884, PD00028572, PS11744884. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This motor pulley is compatible with select gas and electric dryers from the following brands: Whirlpool dryers (gas and electric — WED, WGD, and related series) Kenmore / Sears dryers (Whirlpool-built models) Maytag dryers (gas and electric — MEDC, MED, MGD, and related series) KitchenAid dryers Amana dryers (NED, NGD, and related series) Roper dryers Crosley dryers Estate dryers Inglis dryers Admiral dryers Magic Chef dryers Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Threads onto the motor shaft to serve as the drive belt anchor point — transfers motor rotation to the drum via the drive belt Durable metal construction — resists cracking, stripping, and wear under continuous high-speed motor operation Dimensions: 1-1/8" L x 1-3/8" W x 1-1/8" H — Pulley 29 designation (60Hz motors) Left-hand (reverse) thread — tightens clockwise, loosens counter-clockwise — do not force removal with standard right-hand tools Replaces WP8066184, 8578565, 3394341, 694871, and over 15 additional cross-reference numbers Compatible with 11 major appliance brands on the Whirlpool platform Often replaced together with the drive belt (341241) and idler pulley (279640 or W10837240) for a complete drum drive repair Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 30–45 minutes with basic hand tools including a wrench Product Specifications Part Number 8066184 OEM Part Number WP8066184 Part Type Dryer Motor Pulley Condition Aftermarket Replacement Application Gas and Electric Dryers Material Metal Dimensions 1-1/8" L x 1-3/8" W x 1-1/8" H Pulley Designation Pulley 29 (60Hz) Thread Direction Left-hand (reverse) thread — loosen counter-clockwise Often Replaced With 341241 Drive Belt, 279640 or W10837240 Idler Pulley Compatible Brands Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Crosley, Estate, Inglis, Admiral, Magic Chef Installation Notes ⚠️ Unplug Dryer Before Starting — Left-Hand Thread: Loosen Counter-Clockwise Disconnect power (and shut off gas for gas dryers) before beginning. Remove the top panel and front panel to access the motor and drum area. Release the drive belt tension from the idler pulley and slide the belt off the motor pulley. The motor pulley threads onto the motor shaft with a left-hand (reverse) thread — to remove it, turn it counter-clockwise (which is the tightening direction for standard threads). Use two adjustable wrenches or a wrench and pipe for additional leverage if the pulley is stuck — a penetrating oil applied and allowed to soak for 10–15 minutes can help free a seized pulley. Once removed, thread the new 8066184 pulley clockwise onto the motor shaft (which tightens it due to the left-hand thread) and snug it firmly. Re-route the drive belt around the new motor pulley and idler pulley, reinstall the front and top panels, restore power, and run a test cycle. Tools needed: Phillips screwdriver, two adjustable wrenches or pipe wrench. Frequently Asked Questions What does the dryer motor pulley do? The motor pulley is a small threaded metal wheel that screws onto the dryer motor shaft. The drive belt wraps around the motor pulley on one side and the drum on the other, with the idler pulley maintaining tension. As the motor spins, the motor pulley rotates with it, pulling the belt and turning the drum. Without the motor pulley — or with a cracked or stripped one — the belt has no grip point on the motor side and the drum will not rotate even though the motor is running normally. Why does this pulley have a left-hand (reverse) thread? The motor pulley uses a left-hand thread so that the motor's rotation naturally tightens the pulley during normal operation rather than loosening it. Since the motor spins in a direction that would loosen a standard right-hand thread, Whirlpool designed the motor pulley with a reverse thread to prevent it from backing off and falling loose during use. This means: to remove the old pulley, turn it counter-clockwise (opposite of standard). To install the new pulley, turn it clockwise to tighten. What is the difference between 8066184 and WP8066184? These are the same motor pulley. WP8066184 is the updated Whirlpool OEM part number that superseded the original 8066184. The 8578565 and 3394341 are also cross-references for this same pulley from earlier production runs. This aftermarket replacement is compatible with all of these numbers. Should I also replace the drive belt and idler pulley at the same time? Yes — since the dryer is already disassembled, inspect and replace the drive belt (341241) and idler pulley (279640 or W10837240 depending on your model) at the same time. A broken motor pulley often damages or frays the belt, and the idler pulley bearing wears at a similar rate. Replacing all three together in a single repair eliminates the most common drum drive failure points and prevents a repeat teardown in the near future. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured from durable metal to match the dimensions and thread specification of the original WP8066184 motor pulley. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WE04X10052 Dryer Door Switch - Compatible with GE, Hotpoint Dryers Product Description Ensure safe and reliable operation of your dryer with the replacement XPARTCO WE04X10052 Dryer Door Switch. This door switch is designed for select GE and Hotpoint dryers, preventing operation when the door is open and ensuring proper start/stop functionality. It addresses issues like the dryer not starting, running with the door open, or failing to stop, offering a cost-effective alternative to OEM parts. Note: Includes one door switch. Sold individually. Disconnect power before installation. Verify compatibility with your dryer model. Replaces part numbers: WE04X10052, 877374, WE4X10052, EXPWE4X10052, PD00030680, AH265289, EAP265289, EA265289, AP2042951, PS265289. Compatibility: Compatible with models including but not limited to: GE: WSM2420D0CC , WSM2420D0WW , WSM2420D1CC , WSM2420D1WW , WSM2420D2CC , WSM2420D2WW , WSM2420D3WW , WSM2420D4WW , WSM2420D5WW , WSM2420TAAAA , WSM2420TAACC , WSM2420TAAWW , WSM2420TBAAA , WSM2420TBAWW , WSM2480D0WW , WSM2480D1WW , WSM2480D2WW , WSM2480D3WW , WSM2480TAAAA , WSM2480TAAWW , WSM2480TBAAA , WSM2480TBAWW , WSM2480TCAAA , WSM2480TCAWW Hotpoint: HTDP120EDWW, NVLR333EE0WW, HTDX100GDWW Other brands: Select models requiring WE04X10052 Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select GE, Hotpoint, and other dryers requiring WE04X10052. 🔥 Specifications: replacement dryer door switch, 2- or 3-terminal configuration, push-to-start functionality. 💰 Cost-Effective Alternative: Offers OEM-equivalent performance at a lower price. 🛠️ Easy Installation: Requires Phillips screwdriver, work gloves; typically installed in 5–10 minutes. 🛡️ Effective Fixes: Resolves issues like dryer not starting, running with door open, or failing to stop. Product Specification Part Number: XPWE04X10052 Component Type: Dryer door switch Material: Durable plastic housing with metal contacts Terminal Type: 2- or 3-terminal (model-specific, verify before purchase) Operating Conditions: Suitable for high-heat dryer environments Compliance: UL-listed components, Prop 65 warning for California Installation Notes: Safety First: Disconnect the dryer from the power source before installation. Tools Needed: Phillips screwdriver, work gloves. Process: Locate the door switch near the dryer door frame, disconnect wiring, remove the old switch, and install the new one, ensuring proper terminal connections. Shop for high-quality replacement appliance parts with a 30-day return policy. Keep your dryer running safely today! Add to cart now for a budget-friendly fix!

Read more less

XPARTCO DC47-00016A Dryer Thermostat - Compatible with select Samsung, Whirlpool, Maytag, Kenmore Dryers Product Description Protect your dryer from overheating with the replacement DC47-00016A Dryer Thermostat. This thermal cut-off thermostat is designed for select Samsung, Whirlpool and Kenmore dryers, shutting off the motor when the dryer overheats to prevent damage or hazards. It addresses issues like no heat, insufficient heat, failure to start, or premature shutoff, offering a cost-effective alternative to OEM parts. Note: Includes one thermal cut-off thermostat with two 1/4" male spade terminals. Disconnect power before installation. Replaces part numbers: DC47-00016A, L0016A, AP4201894, PS4205213, AP6008681, EAP4205213, EAP11741821, PD00005341, PD00003747, PS11741821, 35001087, WP35001087. Compatibility: Compatible with models including but not limited to: Samsung: DV203AGS, DV203AGW/XAA-0000, DV206AES, DV209AEW/XAA-0000, DV210AEW, DV42H5000EW/A3, DV45H7000EW/A2, DV48H7400EW/A2 Kenmore: 40289032010, 40289032011, 40299032010, 40299032012 Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Samsung, Kenmore, and LG dryers. 🔥 Specifications: replacement thermal cut-off thermostat, opens at 260°F, two 1/4" male spade terminals. 💰 Cost-Effective Alternative: Offers OEM-equivalent performance at a lower price. 🛠️ Easy Installation: Requires Phillips screwdriver, pliers, work gloves; typically installed in 15–20 minutes. 🛡️ Effective Fixes: Resolves no heat, insufficient heat, failure to start, or premature shutoff. Product Specification Part Number: XPARTCO DC47-00016A Component Type: Thermal cut-off thermostat Material: Metal and plastic Electrical Specs: 125/250V, 25A, 85°C - 35°C, 185°F. Mounting: Two 1/4" male spade terminals, mounts on blower housing Operating Conditions: Suitable for high-temperature dryer environments Compliance: Prop 65 warning for California Installation Notes: Safety First: Disconnect the dryer from the power source before installation. Shop for high-quality replacement appliance parts with a 30-day return policy. Keep your dryer safe and efficient today! Add to cart now for a budget-friendly fix!

Read more less

W10198086 Replacement Dryer Drum Belt - Compatible with Whirlpool, Maytag replaces WPW10198086 Product Description Ensure your dryer’s drum rotates smoothly with the W10198086 Replacement Dryer Drum Belt. This high-quality replacement part is designed for select Whirlpool, Maytag, Kenmore, and other dryers, connecting the motor to the drum to enable proper tumbling during drying cycles. It addresses issues like the drum not spinning, unusual noises, or failure to start, offering a cost-effective alternative to OEM parts with equivalent performance. Note: Includes one dryer drum belt. Disconnect power before installation. Inspect the idler pulley and motor pulley for wear to prevent repeat failures. This is a replacement part designed to match OEM specifications. Replaces part numbers: WPW10198086, W10198086, 1481904, W11575709, W11667279, LB8086, PD00007598, EAP11750135, AP6016842, PS11750135. Compatibility: Compatible with models including but not limited to: Whirlpool: WED9151YW0, WED9050XW0, WED9150WW0, WED9200SQ0, WED9400SW0, WED9500TW0, WGD9151YW0, WGD9200SQ0, WGD9400SW0 Maytag: MED6000XW0, MED7000XW0, MGD6000XW0, MGD7000XW0 Kenmore: 110.67032600, 110.67086600, 110.68812790, 110.78832790, 110.97831790 Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Whirlpool, Maytag, Kenmore, and other dryers. 🔧 Specifications: 92-1/4" long, 5-rib, 1/4" wide belt drives the dryer drum for efficient tumbling. 💰 Cost-Effective Alternative: Offers OEM-equivalent performance at a lower price. 🛠️ Easy Installation: Requires screwdriver, wrench, work gloves; typically installed in 20–40 minutes with YouTube video guidance. 🛡️ Effective Fixes: Resolves drum not spinning, noisy operation, or failure to start. Product Specification Part Number: W10198086 Component Type: Dryer drum belt Material: Durable rubber Dimensions: Approximately 92-1/4" length, 1/4" width, 5 ribs Mounting: Loops around drum, motor pulley, and idler pulley Operating Conditions: Suitable for high-tension dryer drum systems Compliance: Prop 65 warning for California Installation Notes: Safety First: Disconnect the dryer from the power source before installation. Tip: Access the drum by removing the dryer’s top or front panel; thread the belt through the idler pulley and around the motor pulley, ensuring proper tension. Watch YouTube videos for step-by-step guidance. Check idler pulley and motor pulley for wear to avoid premature belt failure. Shop for high-quality replacement appliance parts with a 30-day return policy. Keep your dryer running smoothly today! Add to cart now for a budget-friendly fix!

Read more less

XPARTCO 3977394 Dryer Thermal Cut-Off Kit –  Compatible with Whirlpool, Kenmore, Maytag, and KitchenAid Dryers Product Description Protect your dryer from overheating with the XPARTCO 3977394 Dryer Thermal Cut-Off Kit. This high-quality aftermarket replacement shuts off the heating element if the dryer temperature rises above safe operating limits. A failed cut-off can cause no-heat issues or overheating during drying cycles. Installing this reliable XPARTCO 3977394 kit restores safe temperature control and helps prevent damage to internal components. Replaces Part Numbers XPTC352, 3977394, 352F, EXPTC352 Compatibility This replacement thermal cut-off kit fits select Whirlpool, Kenmore, Maytag, Roper, Estate, Crosley, and KitchenAid dryers. Example compatible models include (but are not limited to): Whirlpool WED4815EW1, Kenmore 110.86573110, and Maytag MEDC215EW1. Always verify your dryer’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM safety and temperature performance 🔥 Overheat Protection – Automatically shuts off power to the heating element if the dryer overheats 💰 Cost-Effective Fix – Affordable alternative to OEM thermal cut-off kits 🛠️ Easy Installation – Direct-fit design with included thermostats and connectors 🛡️ Fixes Common Issues – Solves dryer not heating, overheating, or shutting off prematurely 📐 Product Specification Part Number: 3977394 Component Type: Dryer Thermal Cut-Off Kit Includes: Thermal cut-off, high-limit thermostat, mounting hardware, and wire connectors Temperature Rating: Cut-off opens at ~352°F. Material: Metal thermostat housing and heat-resistant components Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Nut driver, Phillips screwdriver ⚠️ Safety First: Always unplug the dryer before performing any repairs to prevent electrical shock. Steps: Disconnect power and remove the rear dryer panel. Locate the heating element housing and identify the cut-off and thermostat. Disconnect wires and remove the old components. Install the new 3977394 cut-off and thermostat in the same locations. Reconnect wires, reassemble the back panel, and restore power. Run a short test cycle to verify proper heating. ⏱️ Time Required: 15–25 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Keep your dryer safe and efficient — Add to Cart Now for a reliable, budget-friendly repair!

Read more less

ERP 3390719 Dryer Thermal Fuse Single shot 190F/88C. Fits specific Whirlpool and Kenmore dryer models. Thermal Fuse (Disc. Style) Replaces:  WP3390719, 3390719, 15-198, 279650, 3389639, 3389640, 660877, 688841, 690198, 690798, 80004, ET402, AP6008309, PS11741444. Description This dryer Thermal Fuse is a replacement part for specific Whirlpool, Kenmore dryer models. This disposable, one-time fuse ensures safe operation of your appliance by cutting off power if the temperature exceeds safe limits. A bad thermal fuse can cause your appliance to stop functioning or prevent it from turning on altogether. Symptoms of a bad thermal fuse include no heat or a dryer that won't start. Thermal fuse. If the dryer overheats, this device stops the flow of electricity to the heat source and/or the entire dryer. It is located on the blower housing and cannot be reset. The most common cause for overheating is a vent tube clogged with lint, a birds nest or other debris.    This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

XPARTCO WE1M654 Dryer Timer Knob – Compatible with GE & Hotpoint Dryers Product Description Restore smooth and accurate cycle selection with the XPARTCO WE1M654 Dryer Timer Knob. This high-quality aftermarket replacement fits securely onto the dryer’s timer shaft, allowing easy turning and precise control of drying cycles. A cracked, loose, or missing knob can make it difficult to set cycles or operate the dryer properly. Replacing it with this durable XPARTCO knob restores normal operation and improves everyday usability. XPARTCO is a trusted aftermarket brand offering appliance replacement parts built to OEM-equivalent specifications at a cost-effective price. Replaces Part Numbers WE1M654, 1264290, WE01M0443, WE1M443, WE1M502, WE1M668, AH1482197, EA1482197, PD00001146, EAP1482197, AP3995088, PS1482197. Compatibility This replacement dryer timer knob fits select GE and Hotpoint dryers. Example compatible models include (but are not limited to): GE GTDP220EF3WW, GTDP300EM1WS Hotpoint HTDX100EM1WW Always verify your dryer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM fit and appearance 🎛️ Smooth Cycle Control – Restores easy and accurate timer adjustment 🧩 Direct-Fit Design – Push-on fit for secure installation 💪 Durable Plastic Construction – Built for everyday use 💰 Cost-Effective Repair – Affordable alternative to OEM knobs 📐 Product Specification Part Number: WE1M654 Component Type: Dryer Timer Knob Material: High-strength molded plastic Color: White (OEM-style) Mounting: Push-on / shaft-fit Quality Level: Aftermarket replacement (not OEM) 🛠️ Installation Notes Tools Needed: None ⚠️ Safety First: Ensure the dryer is powered off before installing the knob. Basic Steps: Turn the dryer off. Align the new XPARTCO WE1M654 knob with the timer shaft. Press firmly until fully seated. Rotate to confirm smooth operation. ⏱️ Time Required: Under 2 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Aftermarket Appliance Parts 🔄 30-Day Return Policy Restore smooth dryer control in seconds — Add to Cart Now for a quick, budget-friendly fix!

Read more less

XPARTCO XP8767 Dryer Thermostat Set — DC47-00018A, DC96-00887C, DC47-00016A, DC32-00007A The XPARTCO XP8767 is an aftermarket dryer thermal component set containing four heat-sensing and safety parts for select Samsung and Kenmore dryers. The set includes the high-limit thermostat (DC47-00018A), thermal fuse with bracket (DC96-00887C), blower housing thermal fuse (DC47-00016A), and thermistor temperature sensor (DC32-00007A) — the complete set of thermal components that regulate temperature and prevent overheating in compatible Samsung dryers. When any one of these components fails, the dryer may produce no heat, run too hot, shut off too early, or fail to start. Because overheating events that blow a thermal fuse also stress the other thermal components, replacing all four together in a single repair is the recommended approach. The DC96-00887C replaces the DC96-00887A used in earlier models — both are included in this kit's cross-references. Installs in 20–30 minutes with basic hand tools. Quick Answer The XPARTCO XP8767 Dryer Thermostat Set fixes Samsung and Kenmore dryers with no heat, insufficient heat, overheating, early shutoff, or failure to start. Includes all four thermal components: DC47-00018A high-limit thermostat (L260-50), DC96-00887C thermal fuse with bracket (320°F), DC47-00016A blower housing thermal fuse, and DC32-00007A thermistor. Compatible with Samsung and Kenmore (Samsung-built) dryers. Common Problems This Set Fixes Dryer produces no heat — thermal fuse or high-limit thermostat has failed Dryer produces insufficient heat — thermistor not regulating temperature correctly Dryer shuts off too early before clothes are dry Dryer will not start at all Dryer overheats — drum or clothes too hot at end of cycle Dryer cycle runs but timer does not advance Clothes not drying properly despite the dryer running normally What's in the Set Part 1 of 4 DC47-00018A High-Limit Thermostat Rated L260-50 · Opens at 260°F (127°C), resets at 210°F (99°C) · Mounted on the heating element housing · Cuts power to the heating element if drum temperature exceeds safe limits · Auto-resets when cooled · Should show closed continuity at room temperature Part 2 of 4 DC96-00887C Thermal Fuse with Bracket Opens at 320°F (160°C) · One-time safety device mounted on the exhaust duct with bracket · Permanently cuts power to heat source if dryer overheats · Cannot be reset — must be replaced if blown · Replaces DC96-00887A used in earlier models Part 3 of 4 DC47-00016A Thermal Fuse (Blower Housing) Located on the blower housing · One-time safety device that cuts power to the motor if the dryer overheats · Cannot be reset — must be replaced if blown · Should show closed continuity at room temperature when working Part 4 of 4 DC32-00007A Thermistor Temperature Sensor Attached to the blower housing · Varies in resistance during the drying cycle to monitor and regulate drum temperature in real time · Communicates temperature readings to the control board · A failed thermistor causes incorrect drying temperatures, premature shutoff, or erratic cycle behavior Replaces Part Numbers DC47-00018A Dryer Hi Limit Thermostat Dryer high-limit thermostat, L260-50F. Replaces Parts Numbers: DC47-00018A, AP4201898, EAP2430930, PS2430930, ASM33627, PD00002011, 35001092, WP35001092, ASM33627, PD00004704, EAP11741822, AP6008682, PS11741822. DC96-00887C  Dryer Thermal Cut Off The fuse is not re-settable and will need to be replaced if blown. If the dryer does not heat, the thermal fuse may be blown. Replaces Part Numbers: DC96-00887C, DC96-00887A, ASM65115, PD00035400, AP4207819, EAP4216838, PS4216838, 2074129, WP35001193, 35001193, EAP11741829, AP6008689, PS11741829, AWP47381, PD00003365. DC47-00016A Dryer Thermostat Replaces Part Number: DC47-00016A, 2068545, ASM868996, PD00003747, AP4201894, PS4205213, WP35001087, 35001087, AWP47334, PD00003747, AP6008681, PS11741821. DC32-00007A Dryer Thermistor: Dryers Replacement Thermistor Replaces Part Numbers: DC32-00007A, ASM654843, PD00001996, 2068429, AP4201716, PS4204984, WP35001191, 35001191, 1185513, AH2038482, PD00003059, EAP11741828, AP6008688, PS11741828. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This thermostat set is compatible with select dryers from the following brands: Samsung dryers (gas and electric — DV, DVE, DVG series) Kenmore / Sears dryers (select Samsung-built models) Important: If a thermal fuse has blown, always check for the root cause before replacing — a clogged exhaust vent is the most common cause of dryer overheating. Clean the full length of the exhaust duct before running the dryer after this repair. Key Features Complete 4-part thermal set — covers all Samsung dryer thermal components in a single repair DC47-00018A high-limit thermostat (L260-50) — auto-resets; cuts heating element power at 260°F DC96-00887C thermal fuse with bracket (320°F) — one-time safety device; replaces DC96-00887A used in earlier models DC47-00016A thermal fuse on blower housing — one-time safety device that protects the motor DC32-00007A thermistor — monitors real-time drum temperature and communicates with the control board to regulate drying cycles Replacing all four parts together renews the complete thermal circuit — prevents recurrence if a failing component caused the fuse to blow Compatible with Samsung DV, DVE, and DVG series dryers and Samsung-built Kenmore models Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 20–30 minutes with basic hand tools Product Specifications Set Part Number XP8767 Condition Aftermarket Replacement Application Samsung and Kenmore Gas and Electric Dryers Set Includes 1x DC47-00018A High-Limit Thermostat, 1x DC96-00887C Thermal Fuse with Bracket, 1x DC47-00016A Thermal Fuse, 1x DC32-00007A Thermistor DC47-00018A Rating L260-50 — opens at 260°F (127°C), resets at 210°F (99°C) — auto-resets DC96-00887C Trip Temp 320°F (160°C) — one-time, non-resettable DC47-00016A One-time thermal fuse on blower housing — non-resettable DC32-00007A Thermistor — resistance varies with temperature; communicates with control board Compatible Brands Samsung, Kenmore (Samsung-built) Installation Notes ⚠️ Unplug Dryer and Shut Off Gas Before Starting Disconnect power (and shut off gas for gas dryers) before beginning. Remove the back panel of the dryer to access the heating element housing and exhaust duct. Take a photo of all wire connections before disconnecting anything — the thermistor and thermal fuses use similar small connectors and it is important to reconnect them to the correct terminals. The DC47-00018A high-limit thermostat is mounted on the heating element housing — unscrew and replace it. The DC96-00887C thermal fuse with bracket is mounted on the exhaust duct — unscrew, remove the bracket assembly, and install the new one. The DC47-00016A thermal fuse is on the blower housing — disconnect the wires and unscrew or unclip it. The DC32-00007A thermistor is clipped to the blower housing — pull the old one out and press the new one into the clip. Reconnect all wires, reassemble the back panel, restore power, and run a test cycle. Tip: Clean the full length of the exhaust duct before running the dryer after this repair. Tools needed: Phillips screwdriver, 1/4" nut driver, needle-nose pliers. Frequently Asked Questions What does each part in this set do? The DC47-00018A high-limit thermostat monitors the heating element temperature and cuts power to the element at 260°F if the dryer gets too hot — it resets automatically when cooled. The DC96-00887C thermal fuse is a one-time safety device on the exhaust duct that permanently cuts power to the heat source at 320°F if the dryer overheats. The DC47-00016A is a second one-time thermal fuse on the blower housing that cuts power to the motor if overheating occurs there. The DC32-00007A thermistor monitors real-time drum temperature and sends resistance-based readings to the control board, which uses them to regulate the drying cycle and control the heating element. What is the difference between DC96-00887A and DC96-00887C? The DC96-00887C is the updated current part number that superseded the DC96-00887A. Both are the same thermal fuse with bracket used on the exhaust duct — the C suffix denotes a minor revision. Either part number is covered by this kit and both are fully interchangeable. How do I test these parts with a multimeter? Set the multimeter to continuity or resistance mode. At room temperature, the DC47-00018A high-limit thermostat and both thermal fuses (DC96-00887C and DC47-00016A) should all show closed continuity (near-zero resistance). Any of these that reads open (no continuity) has failed. The DC32-00007A thermistor should show a resistance reading at room temperature — typically around 10,000–50,000 ohms depending on ambient temperature — rather than zero or open. A thermistor that reads open or zero at room temperature has failed. Why should I replace all four parts instead of just the one that failed? When a thermal fuse blows in a Samsung dryer, it almost always means the dryer overheated — and that overheating event stresses all four thermal components simultaneously. Replacing just the blown fuse without replacing the other parts risks a repeat failure if the thermistor is providing incorrect readings or the high-limit thermostat is no longer protecting accurately. Replacing all four parts at once renews the entire thermal circuit and reduces the chance of a repeat failure in the near future. Is this set for electric and gas Samsung dryers? Yes — the XP8767 set is compatible with both electric (DVE series) and gas (DVG series) Samsung dryers that use these four thermal components. Always verify your specific model number before ordering to confirm all four parts apply to your dryer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 3390719 Dryer Thermal Fuse – Replaces WP3390719 – Compatible with Whirlpool, Maytag & Kenmore Dryers Product Description Restore safe dryer operation and proper heating with the XPARTCO 3390719 Dryer Thermal Fuse. This dryer Thermal Fuse is a replacement part for specific Whirlpool, Kenmore dryer models. This disposable, one-time fuse ensures safe operation of your appliance by cutting off power if the temperature exceeds safe limits. A bad thermal fuse can cause your appliance to stop functioning or prevent it from turning on altogether. Symptoms of a bad thermal fuse include no heat or a dryer that won't start. It is located on the blower housing and cannot be reset. XPARTCO is a trusted aftermarket brand offering appliance replacement parts built to OEM-equivalent specifications at a cost-effective price. Replaces Part Numbers WP3390719, 3390719, 15-198, 279650, 3389639, 3389640, 660877, 688841, 690198, 690798, 80004, ET402, G4AP0401, PD00002330, EAP11741444, AP6008309, PS11741444. Compatibility This replacement dryer thermal fuse fits select Whirlpool, Maytag, Kenmore, Amana, Estate, Roper, and Crosley dryers. Commonly installed on the blower housing or exhaust duct, depending on model. Always verify your dryer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM safety and temperature ratings 🛡️ Overheat Protection – Shuts off power if unsafe temperatures are detected 🔥 Fixes No-Heat or No-Run Issues – Common solution for blown fuse symptoms 🧩 Direct-Fit Design – Installs easily without modification 💰 Cost-Effective Repair – Reliable alternative to OEM thermal fuses 📐 Product Specification Part Number: 3390719 Component Type: Dryer Thermal Fuse Function: One-time over-temperature safety cutoff Application: Blower housing or exhaust system Mounting: Screw-mounted Quality Level: Aftermarket replacement (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver ⚠️ Safety First: Unplug the dryer before servicing to avoid electrical shock. Basic Steps: Disconnect dryer power. Remove the rear or front access panel (model dependent). Locate the thermal fuse on the blower housing or exhaust duct. Disconnect wires and remove the old fuse. Install the new XPARTCO 3390719 thermal fuse. Reconnect wiring, reassemble panels, and restore power. Test dryer operation. ⏱️ Time Required: 15–20 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Aftermarket Appliance Parts 🔄 30-Day Return Policy Restore dryer safety and reliable operation — Add to Cart Now for a dependable, budget-friendly repair!

Read more less

XPARTCO 279973 Dryer Thermostat Kit The XPARTCO 279973 is an aftermarket replacement dryer thermostat and thermal cut-off kit compatible with a wide range of Whirlpool-family electric dryers including Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Inglis, Roper, and Admiral. The kit contains two components — the high-limit thermostat (L295-80F) and the thermal cut-off fuse — both located on the heating element housing. Together they protect the dryer's heating element from overheating: the high-limit thermostat monitors element temperature and cuts power if it exceeds safe levels, then resets when cooled. The thermal cut-off fuse is a backup one-time device that permanently opens the circuit if the thermostat fails to protect the element. Both parts are mounted on the side of the heating element housing and can be accessed through the dryer's back panel. The thermal cut-off fuse is a non-resettable one-time device — once it opens, it must be replaced. The 279973 kit includes both parts, an instruction sheet, and hardware. It directly replaces 3391913, 3404151, 3404152, 3977395, 8318314, 897710, 279973VP, AP3094323, and several additional cross-reference numbers. Note: this kit is for electric dryers only. Installs in 20–30 minutes with basic hand tools. Quick Answer The XPARTCO 279973 Dryer Thermostat Kit fixes Whirlpool-family electric dryers with no heat, overheating, or a dryer that shuts off too early. Kit includes the L295-80F high-limit thermostat (auto-reset, opens at 295°F) and the thermal cut-off fuse (352°F, one-time). Both mount on the heating element housing. Electric dryers only. Replaces 3391913, 3404151, 8318314, 897710, AP3094323. Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Inglis, Roper, and Admiral. Common Problems This Kit Fixes Dryer produces no heat — thermal cut-off fuse or high-limit thermostat has failed Dryer overheats — clothes or drum too hot at the end of a cycle Dryer shuts off early before clothes are dry Dryer takes multiple cycles or very long time to dry clothes Repeated no-heat failures — underlying overheating condition affecting the element housing components Dryer tumbles normally but produces no heat at all What's in the Kit Part 1 of 2 High-Limit Thermostat (L295-80F) Opens at 295°F — cuts power to the heating element if temperature exceeds safe levels · Auto-resets when cooled · Located on the heating element housing · Should show closed continuity (near-zero resistance) at room temperature Part 2 of 2 Thermal Cut-Off Fuse (352°F) Opens at 352°F — one-time backup safety device on the heating element housing · Permanently interrupts power to the heating element if the high-limit thermostat fails to protect it · Cannot be reset — must be replaced if blown · Should show closed continuity at room temperature when working Replaces Part Numbers This thermostat kit directly replaces the following OEM and cross-reference part numbers: 279973, 279973VP, 3391913, 3404151, 3404152, 3977395, 8318314, 897710, ER279973, PD00002626, EAP334387, AWP39286, AH334387, AP3094323, EA334387, PS334387. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This thermostat kit is compatible with select electric dryers only from the following brands: Whirlpool electric dryers (Duet, Cabrio, and standard series) Kenmore / Sears electric dryers (Whirlpool-built models) Maytag electric dryers KitchenAid electric dryers Amana electric dryers Inglis electric dryers Roper electric dryers Admiral electric dryers Important: This kit is for electric dryers only. Gas dryers use a different burner assembly and require a different thermostat kit (XP6974 for Whirlpool-family gas dryers). Always verify your dryer type and model number before ordering. Also: if the thermal cut-off fuse has blown, always check for a clogged exhaust vent before replacing — a blocked vent is the most common root cause of overheating and repeated fuse failures. Key Features 2-part kit — high-limit thermostat and thermal cut-off fuse, both on the heating element housing High-limit thermostat (L295-80F) — opens at 295°F to cut element power, auto-resets when cooled Thermal cut-off fuse (352°F) — one-time backup safety device; permanently opens if thermostat fails to protect the element Both parts located on the heating element housing — accessible from the dryer back panel Replacing both together ensures complete thermal protection is restored on the element housing Replaces 3391913, 3404151, 8318314, 897710, AP3094323, and over 10 additional cross-reference numbers Electric dryers only — not for gas dryer models Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Inglis, Roper, and Admiral electric dryers Aftermarket replacement built to OEM-equivalent quality standards Installs in 20–30 minutes with basic hand tools Product Specifications Kit Part Number 279973 Condition Aftermarket Replacement Application Electric Dryers Only Kit Includes 1x High-Limit Thermostat (L295-80F), 1x Thermal Cut-Off Fuse (352°F), hardware, instruction sheet High-Limit Thermostat Rating L295-80F — opens at 295°F, resets at 215°F — auto-resets Thermal Cut-Off Fuse Trip Temp 352°F — one-time, non-resettable Location Heating element housing (both parts) Compatible Brands Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Inglis, Roper, Admiral Installation Notes ⚠️ Unplug Dryer Before Starting — Electric Dryers Only Disconnect power before beginning. Remove the back panel of the dryer by unscrewing the perimeter screws to expose the heating element housing. Both the high-limit thermostat and thermal cut-off fuse are mounted on the side of the heating element housing — the thermostat is typically the larger component and the thermal cut-off fuse is smaller. Test each component with a multimeter before removing (both should show closed continuity at room temperature; the failed one will read open). Photograph the wiring before disconnecting. Disconnect the wires, remove the mounting screws, and install the new components in the same positions. Reconnect the wires and mounting screws, reinstall the back panel, restore power, and run a test cycle to confirm heat. Tip: Before running the dryer, clean the full length of the exhaust duct — a clogged vent is the most common cause of overheating and a blown thermal cut-off fuse. Tools needed: Phillips screwdriver, 1/4" nut driver, multimeter. Frequently Asked Questions What is the difference between the high-limit thermostat and the thermal cut-off fuse in this kit? The high-limit thermostat (L295-80F) is a resettable safety switch that opens at 295°F to cut power to the heating element and resets automatically when the temperature drops. It is the primary protection against overheating during normal operation. The thermal cut-off fuse is a one-time backup device rated at 352°F — it permanently opens the circuit if the heating element temperature climbs beyond the point the thermostat should have caught. Once the cut-off fuse opens, it must be replaced; it does not reset on its own. If the cut-off fuse has blown, it usually means the high-limit thermostat also failed to do its job and should be replaced at the same time — which is exactly what this kit provides. How do I test these parts with a multimeter? Unplug the dryer and remove the back panel to access the heating element housing. Disconnect each component from the wiring and probe both terminals with a multimeter set to continuity or resistance mode. At room temperature, both the high-limit thermostat and the thermal cut-off fuse should show closed continuity (near-zero resistance). Any component that reads open circuit (no continuity) has failed and needs to be replaced. The thermal cut-off fuse reads open even after it cools — it is non-resettable. The high-limit thermostat may read open at room temperature if it has failed internally rather than by an overheat trip. How is the 279973 kit different from the XP6974 thermostat kit? The 279973 is a 2-part kit — high-limit thermostat and thermal cut-off fuse — designed specifically for the heating element housing of Whirlpool-family electric dryers. The XP6974 is a 4-part kit — cycling thermostat, thermal fuse, high-limit thermostat, and thermal cut-off — designed for Whirlpool-family gas and electric dryers, covering both the exhaust duct components and the burner/element housing components. If your electric dryer is showing no-heat and you need only the heating element housing components, the 279973 kit covers exactly those two parts. If you want to replace all thermal components in one repair, the XP6974 covers a broader set. Why does the thermal cut-off fuse keep blowing? If the thermal cut-off fuse blows repeatedly after replacement, it almost always means there is an underlying overheating condition causing the heating element housing to run hotter than it should. The most common cause is a clogged or restricted exhaust vent — lint accumulation in the duct reduces airflow, trapping heat inside the dryer cabinet and around the element. Other causes include a failed cycling thermostat that is not regulating element temperature correctly, a stuck heating element relay, or a dryer in an enclosed space with inadequate ventilation. Always clean the full exhaust duct and check the cycling thermostat (WP3387134) before replacing the thermal cut-off fuse a second time. Is this an OEM or aftermarket part? This is an aftermarket replacement kit built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the temperature ratings and specifications of the original 279973 high-limit thermostat and thermal cut-off fuse kit. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO W11429587 Dryer Door Catch The XPARTCO W11429587 is an aftermarket replacement dryer door catch compatible with a wide range of Whirlpool-family dryers including Whirlpool, Maytag, Amana, Kenmore, KitchenAid, Jenn-Air, Admiral, Roper, Inglis, Crosley, Magic Chef, and Norge. The door catch is the plastic spring-clip mechanism mounted on the dryer door or front panel that snaps over the door strike to hold the dryer door firmly closed during operation. When the catch breaks or wears out, the door will not stay closed, the dryer will not start, or the door will pop open mid-cycle. This is a sold-as-single door catch with a snap-in installation that typically takes under five minutes and requires no tools. It directly replaces OEM part numbers WPW10610880, W10610880, W10529190, W10696503, and W11224630 — all of which were superseded by the current W11429587 part number. Made from durable plastic designed to withstand repeated opening and closing through the life of the dryer. Quick Answer The XPARTCO W11429587 Dryer Door Catch fixes Whirlpool-family dryers where the door won't stay closed, pops open during a cycle, or where the dryer won't start because the door switch isn't being activated. Sold individually. Snap-in installation — no tools required, installs in under 5 minutes. Compatible with Whirlpool, Maytag, Amana, Kenmore, KitchenAid, Jenn-Air, Admiral, Roper, Inglis, Crosley, Magic Chef, and Norge dryers. Common Problems This Part Fixes Dryer door will not stay closed during the drying cycle Door pops open mid-cycle, interrupting the drying cycle Dryer will not start because the door is not latching securely enough to activate the door switch Door feels loose, wiggly, or does not click shut when closed Broken, cracked, or missing door catch visible on the door or front panel Door repeatedly needs to be pushed or held closed to keep the dryer running Replaces Part Numbers This door catch directly replaces the following OEM and cross-reference part numbers: W11429587, WPW10610880, W10529190, W10610880, W10696503, 4959535, AWP44536, EAP12745673, PD00071341, AP6983349, PS12745673. W11429587 is the current updated part number superseding WPW10610880, W10610880, W10529190, W10696503, and W11224630. If your dryer's parts diagram shows any of these older numbers, the W11429587 is the correct current replacement. Compatibility This door catch is compatible with select dryers from the following brands: Whirlpool dryers (gas and electric) Maytag dryers (gas and electric) Amana dryers Kenmore / Sears dryers (select Whirlpool-built models) KitchenAid dryers Jenn-Air dryers Admiral dryers Roper dryers Inglis dryers Crosley dryers Magic Chef dryers Norge dryers Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Holds the dryer door firmly closed during operation so the door switch remains engaged and the dryer runs uninterrupted Snap-in installation — no screws, no tools required in most cases; installs in under 5 minutes Durable plastic construction — designed to withstand repeated opening and closing over the life of the dryer Current updated part number — directly supersedes WPW10610880, W10610880, W10529190, W10696503, and W11224630 Sold individually — one door catch per order Compatible with 12 major appliance brands on the Whirlpool platform Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number W11429587 Also Replaces WPW10610880, W10610880, W10529190, W10696503, W11224630 Part Type Dryer Door Catch (Door Latch Catch Clip) Condition Aftermarket Replacement Application Gas and Electric Dryers Material Plastic Color White Installation Snap-in — no tools required in most cases Sold As Single door catch Compatible Brands Whirlpool, Maytag, Amana, Kenmore, KitchenAid, Jenn-Air, Admiral, Roper, Inglis, Crosley, Magic Chef, Norge Installation Notes ⚠️ Unplug Dryer Before Starting Disconnect power before beginning. Open the dryer door and locate the old door catch — it is typically mounted in a rectangular slot on the inside of the door or on the dryer front panel near the door opening. Use a small flat-head screwdriver or your fingers to press the tabs on the old catch and pop it out of its mounting slot. Note the orientation of the old catch before removing it. Insert the new W11429587 catch into the slot in the same orientation and press firmly until it snaps into place. Close the dryer door to confirm it latches securely with a positive click. Restore power and run a short cycle to verify the door stays closed and the dryer operates normally. Tools needed: None in most cases; a small flat-head screwdriver may help with removal. Frequently Asked Questions What is the difference between W11429587, WPW10610880, and W10610880? These are all part numbers for the same dryer door catch used across different Whirlpool-family production runs. W10610880 was the original number, WPW10610880 was an intermediate update, and W11429587 is the current manufacturer-approved part number. W10529190, W10696503, and W11224630 are also cross-referenced to this same catch. If your parts diagram shows any of these numbers, the W11429587 is the correct replacement to order. Why won't my dryer start even though I'm closing the door? If the door catch is broken or worn, the door may not be engaging the door switch firmly enough to signal the control board that the door is closed. Most dryers are designed not to run unless the door switch is fully activated. A new door catch restores the firm snap that fully depresses the door switch, allowing the dryer to start. If replacing the catch does not resolve the start issue, the door switch itself may also need to be checked. Do I need to replace the door strike as well? Not necessarily — in most cases only the door catch (the spring-clip part) needs replacement. The door strike (the post or tab on the opposite side that the catch snaps onto) is a separate and typically more durable part that rarely fails on its own. Inspect the door strike for cracks or breakage before ordering — if it is intact, just the W11429587 catch is all you need. How many door catches does my dryer have? Most Whirlpool-family dryers use a single door catch. This listing is for one catch. If your dryer door has two catch points, verify your model number with our support team to confirm whether one or two catches are needed before ordering. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured from durable plastic to match the dimensions and function of the original W11429587 door catch. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

XPARTCO DC96-00887C Dryer Thermal Cut Off Fuse – Compatible with Samsung & Kenmore Dryers Product Description Protect your dryer from overheating with the XPARTCO DC96-00887C Dryer Thermal Cut Off Fuse. This Thermal Fuse Assembly is a replacement part for select Samsung, Kenmore, Maytag, Whirlpool clothes dryer models. It provides overheating protection for heating elements and motors inside the dryer chamber. Common causes of a faulty fuse can include normal wear from consistent temperature exposure. Overheating events may also burn out the fuse prematurely. Replaces Part Numbers DC96-00887C, DC96-00887A, PD00035400, EAP4216838, AP5966894, PS4276292, WP35001193, 35001193, PD00003365, EAP11741829, AP6008689, PS11741829. Compatibility This replacement thermal cut off fuse fits select Samsung and Kenmore (Samsung-manufactured) electric dryers. Example compatible models include (but are not limited to):Samsung DV210AEW, DV330AEW, DV42H5000EWKenmore 592-49045, 592-49303 Always verify your dryer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM safety cutoff performance 🔥 Overheat Protection – Permanently opens circuit when unsafe temperatures occur 🛡️ Critical Safety Component – Helps prevent damage to heating system 💰 Cost-Effective Repair – Reliable alternative to OEM pricing 🛠️ Direct-Fit Installation – Installs easily on heater housing 📐 Product Specification Part Number: DC96-00887C Component Type: Dryer Thermal Cut Off Fuse Function: One-time safety cutoff Material: Heat-resistant metal body Mounting: Screw-mounted on heater assembly Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver ⚠️ Safety First: Always unplug the dryer before servicing to avoid electrical shock. Steps: Disconnect dryer power and remove the rear access panel. Locate the thermal cut-off fuse on the heater housing. Disconnect wires and remove the old fuse. Install the new XPARTCO DC96-00887C fuse in the same position. Reconnect wiring, reinstall panel, and restore power. Test dryer heating operation. ⏱️ Time Required: 10–15 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Restore dryer safety and proper heating — Add to Cart Now for a dependable, budget-friendly repair!

Read more less