W10599356 Genuine OEM Whirlpool Washer Water Inlet Valve The W10599356 is a genuine Whirlpool OEM water inlet valve for Whirlpool-built front-load washers, including full-size and compact models. This valve sits at the back of the washer where the hot and cold water supply hoses connect, and it's the gatekeeper for every drop of water that enters the drum. When the control calls for water, it energizes the valve's solenoid coils to open the hot side, the cold side, or both together, and closes them again once the correct fill level is reached. A valve that won't open leaves you with no fill at all; a valve that won't fully close can let water trickle or flow into the drum even when the cycle isn't calling for it. Over time, mineral deposits and sediment from the water supply can build up inside the valve body and prevent it from sealing fully, the internal solenoid coil can burn out electrically, and the rubber diaphragm or seal inside can simply wear out with age. A failing valve on this platform commonly triggers an F8 E1 or similar fill-related error code, since the control expects water to reach the correct level within a set time and flags it when that doesn't happen. It directly replaces AP5692067, 3023192, PS8689091, and W10509710. As a genuine OEM part, the W10599356 is manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. Quick Answer The W10599356 Genuine OEM Whirlpool Washer Water Inlet Valve fixes Whirlpool-built front-load washers that won't fill, fill slowly, overfill, leak water into the drum when the cycle isn't running, or throw an F8 E1 or similar fill-related error code. Solenoid-actuated water inlet valve for the hot and cold supply connections. Replaces AP5692067, 3023192, PS8689091, W10509710. Consider replacing the fill hoses at the same time — they wear on a similar schedule and share the same access point. Common Problems This Part Fixes Washer won't fill with water at the start of the cycle Washer fills much more slowly than normal Washer overfills or takes on more water than the cycle calls for Water trickling or leaking into the drum when the washer is off or between cycles F8 E1 or similar fill-related error code displayed on the control panel Cycle stalling at the fill step and never advancing to wash No hot water, no cold water, or neither reaching the drum Water pooling underneath or behind the washer near the supply connections Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer water inlet valve directly replaces the following OEM and cross-reference part numbers: W10599356, W10509710, AP5692067, 3023192, 33090084, C-022/16-B21, EAP8689091, AWP41165, PD00022876, PS8689091 W10509710 was the immediately preceding number that Whirlpool revised to W10599356. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water inlet valve is compatible with select Whirlpool-built front-load washers across the Whirlpool family of brands, including: Whirlpool front-load washers — WFW series Maytag front-load washers — MHW series (select Whirlpool-built models) KitchenAid, Jenn-Air, and Amana front-load washers (select models) Magic Chef, Admiral, and Norge front-load washers (select models) Roper and Kenmore front-load washers (select Whirlpool-built models) Verified model numbers include: WFW70HEBW0, WFW70HEBW1, WFW70HEBW2, WFW72HEDW0, WFW7590FW0, WFW75HEFW0, WFW80HEBC0, WFW80HEBC1, WFW80HEBC2, WFW80HEBW0, WFW80HEBW1, WFW80HEBW2, WFW81HEDW0, MHW3000BG0, MHW3000BG1, MHW3000BG2, MHW3000BW0, MHW3000BW1, MHW3000BW2, MHW3100DW0, MHW4000BW1, MHW4000BW2, MHW4100DW0, MHW5100DC0, MHW5100DW0, NFW5700BW0, NFW5700BW1, NFW5800DW0, 7MWFW72HEDW0, 7MWFW80HEBW0, and 7MWFW81HEDW0. Note: This valve fits Whirlpool's front-load washer platform. It is not intended for top-load washers, which use a different valve design and mounting configuration. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine Whirlpool OEM part — factory-specified solenoid, seal, and flow-rate design Resolves "won't fill," "fills slowly," "overfills," and "leaking into the drum" symptoms caused by valve failure Commonly resolves F8 E1 and similar fill-related error codes Direct drop-in replacement for the superseded W10509710 valve Replaces AP5692067, 3023192, PS8689091, and W10509710 Compatible with a wide range of Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore front-load washers Genuine OEM replacement — guaranteed fit, materials, and performance Straightforward DIY repair — typically completed in 30 to 60 minutes Product Specifications Part Number W10599356 Part Type Washer Water Inlet Valve Condition Genuine OEM Application Front-Load Washers (Whirlpool-Built) Actuation Solenoid-operated Connections Hot and cold water supply inlets Supersedes W10509710 Repair Difficulty Easy to Moderate — 30 to 60 minutes Quantity 1 valve Compatible Brands Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore Installation Notes ⚠️ Shut Off Water Supply And Unplug Washer Before Starting — Have A Towel Ready Unplug the washer or shut off its circuit breaker, and shut off both the hot and cold water supply valves before beginning. Wear work gloves. Disconnect the hot and cold water supply lines from the back of the valve first — have a towel or shallow pan ready, since residual water will spill out. Use a 1/4" nut driver or socket to remove the rear screws securing the top panel, then slide the panel back and lift it off to access the valve from inside the cabinet. Photograph the wiring connections before disconnecting anything. Disconnect the electrical connector from the old valve, remove the mounting screw or bracket (often a T-20 Torx screw), and pull the valve free from its mounting position. Install the new W10599356 in the same orientation, secure the mounting screw, and reconnect the electrical connector fully. Reattach the hot and cold water supply lines to the correct ports, tightening securely by hand plus a partial turn with pliers. Reinstall the top panel, restore the water supply, and check every connection you touched for leaks before restoring power. Run a short cycle and confirm the tub fills at the normal rate with no leaking underneath or behind the washer. While everything is accessible, consider replacing the fill hoses as well, since they wear on a similar schedule. Tools needed: 1/4" nut driver or socket, T-20 Torx bit, pliers, towel or shallow pan, work gloves. Frequently Asked Questions My washer shows an F8 E1 error. Does that mean the valve is definitely bad? It's a strong indicator, but check the basics first. F8 E1 and similar fill-related codes generally mean the control didn't see water reach the expected level within its allotted fill time. Before replacing the valve, confirm both hot and cold supply valves at the wall are fully open, check the inlet screens inside the valve ports for sediment or debris, and make sure the fill hoses aren't kinked. If those check out and the washer still won't fill properly, the inlet valve itself is the likely cause. Water keeps trickling into the drum even when the washer is off. Is that the valve? Yes, this is one of the classic symptoms of a valve that isn't sealing fully closed. Mineral deposits, sediment, or a worn internal diaphragm can prevent the valve from shutting off completely, letting a slow trickle of water continue into the drum between cycles. This can eventually lead to an overfill or water pooling at the front of the washer, so it's worth addressing promptly rather than waiting. Only hot or only cold water isn't coming in. Do I need to replace the whole valve? Usually yes. Most washer inlet valves use two separate solenoid coils in one housing — one for hot, one for cold — but they're not typically sold as separately replaceable coils. If just one side has stopped working while the other functions normally, that still points to a failure inside this valve assembly, and replacing the complete unit is the standard repair. Should I replace the fill hoses while I'm in there? It's a good idea. The fill hoses connect right at the same point you'll already have exposed, wear on a similar timeline as the valve, and are a common source of slow leaks that get blamed on the valve. Since you're already accessing this area, replacing hoses that show any cracking, bulging, or stiffness saves you from repeating the disassembly later. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It includes the same solenoid design, seal, and flow-rate calibration as the water inlet valve originally installed in your front-load washer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO W10599356 Washer Water Valve The XPARTCO W10599356 is an aftermarket replacement water inlet valve for Whirlpool-built front-load washers, including full-size and compact models. This valve sits at the back of the washer where the hot and cold water supply hoses connect, and it's the gatekeeper for every drop of water that enters the drum. When the control calls for water, it energizes the valve's solenoid coils to open the hot side, the cold side, or both together, and closes them again once the correct fill level is reached. A valve that won't open leaves you with no fill at all; a valve that won't fully close can let water trickle or flow into the drum even when the cycle isn't calling for it. Over time, mineral deposits and sediment from the water supply can build up inside the valve body and prevent it from sealing fully, the internal solenoid coil can burn out electrically, and the rubber diaphragm or seal inside can simply wear out with age. A failing valve on this platform commonly triggers an F8 E1 or similar fill-related error code, since the control expects water to reach the correct level within a set time and flags it when that doesn't happen. It directly replaces AP5692067, 3023192, PS8689091, and W10509710. Quick Answer The XPARTCO W10599356 Washer Water Valve fixes Whirlpool-built front-load washers that won't fill, fill slowly, overfill, leak water into the drum when the cycle isn't running, or throw an F8 E1 or similar fill-related error code. Solenoid-actuated water inlet valve for the hot and cold supply connections. Replaces AP5692067, 3023192, PS8689091, W10509710. Consider replacing the fill hoses at the same time — they wear on a similar schedule and share the same access point. Common Problems This Part Fixes Washer won't fill with water at the start of the cycle Washer fills much more slowly than normal Washer overfills or takes on more water than the cycle calls for Water trickling or leaking into the drum when the washer is off or between cycles F8 E1 or similar fill-related error code displayed on the control panel Cycle stalling at the fill step and never advancing to wash No hot water, no cold water, or neither reaching the drum Water pooling underneath or behind the washer near the supply connections Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer water inlet valve directly replaces the following OEM and cross-reference part numbers: W10599356, W10509710, AP5692067, 3023192, 33090084, C-022/16-B21, EAP8689091, AWP41165, PD00022876, PS8689091 W10509710 was the immediately preceding number that Whirlpool revised to W10599356. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water inlet valve is compatible with select Whirlpool-built front-load washers across the Whirlpool family of brands, including: Whirlpool front-load washers — WFW series Maytag front-load washers — MHW series (select Whirlpool-built models) KitchenAid, Jenn-Air, and Amana front-load washers (select models) Magic Chef, Admiral, and Norge front-load washers (select models) Roper and Kenmore front-load washers (select Whirlpool-built models) Verified model numbers include: WFW70HEBW0, WFW70HEBW1, WFW70HEBW2, WFW72HEDW0, WFW7590FW0, WFW75HEFW0, WFW80HEBC0, WFW80HEBC1, WFW80HEBC2, WFW80HEBW0, WFW80HEBW1, WFW80HEBW2, WFW81HEDW0, MHW3000BG0, MHW3000BG1, MHW3000BG2, MHW3000BW0, MHW3000BW1, MHW3000BW2, MHW3100DW0, MHW4000BW1, MHW4000BW2, MHW4100DW0, MHW5100DC0, MHW5100DW0, NFW5700BW0, NFW5700BW1, NFW5800DW0, 7MWFW72HEDW0, 7MWFW80HEBW0, and 7MWFW81HEDW0. Note: This valve fits Whirlpool's front-load washer platform. It is not intended for top-load washers, which use a different valve design and mounting configuration. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement solenoid-actuated water inlet valve for hot and cold supply connections Resolves "won't fill," "fills slowly," "overfills," and "leaking into the drum" symptoms caused by valve failure Commonly resolves F8 E1 and similar fill-related error codes Direct drop-in replacement for the superseded W10509710 valve Replaces AP5692067, 3023192, PS8689091, and W10509710 Compatible with a wide range of Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore front-load washers Aftermarket replacement built to OEM-equivalent quality standards Straightforward DIY repair — typically completed in 30 to 60 minutes Product Specifications Part Number W10599356 OEM Part Number W10599356 (formerly W10509710) Part Type Washer Water Inlet Valve Condition Aftermarket Replacement Application Front-Load Washers (Whirlpool-Built) Actuation Solenoid-operated Connections Hot and cold water supply inlets Supersedes W10509710 Repair Difficulty Easy to Moderate — 30 to 60 minutes Quantity 1 valve Compatible Brands Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore Installation Notes ⚠️ Shut Off Water Supply And Unplug Washer Before Starting — Have A Towel Ready Unplug the washer or shut off its circuit breaker, and shut off both the hot and cold water supply valves before beginning. Wear work gloves. Disconnect the hot and cold water supply lines from the back of the valve first — have a towel or shallow pan ready, since residual water will spill out. Use a 1/4" nut driver or socket to remove the rear screws securing the top panel, then slide the panel back and lift it off to access the valve from inside the cabinet. Photograph the wiring connections before disconnecting anything. Disconnect the electrical connector from the old valve, remove the mounting screw or bracket (often a T-20 Torx screw), and pull the valve free from its mounting position. Install the new W10599356 in the same orientation, secure the mounting screw, and reconnect the electrical connector fully. Reattach the hot and cold water supply lines to the correct ports, tightening securely by hand plus a partial turn with pliers. Reinstall the top panel, restore the water supply, and check every connection you touched for leaks before restoring power. Run a short cycle and confirm the tub fills at the normal rate with no leaking underneath or behind the washer. While everything is accessible, consider replacing the fill hoses as well, since they wear on a similar schedule. Tools needed: 1/4" nut driver or socket, T-20 Torx bit, pliers, towel or shallow pan, work gloves. Frequently Asked Questions My washer shows an F8 E1 error. Does that mean the valve is definitely bad? It's a strong indicator, but check the basics first. F8 E1 and similar fill-related codes generally mean the control didn't see water reach the expected level within its allotted fill time. Before replacing the valve, confirm both hot and cold supply valves at the wall are fully open, check the inlet screens inside the valve ports for sediment or debris, and make sure the fill hoses aren't kinked. If those check out and the washer still won't fill properly, the inlet valve itself is the likely cause. Water keeps trickling into the drum even when the washer is off. Is that the valve? Yes, this is one of the classic symptoms of a valve that isn't sealing fully closed. Mineral deposits, sediment, or a worn internal diaphragm can prevent the valve from shutting off completely, letting a slow trickle of water continue into the drum between cycles. This can eventually lead to an overfill or water pooling at the front of the washer, so it's worth addressing promptly rather than waiting. Only hot or only cold water isn't coming in. Do I need to replace the whole valve? Usually yes. Most washer inlet valves use two separate solenoid coils in one housing — one for hot, one for cold — but they're not typically sold as separately replaceable coils. If just one side has stopped working while the other functions normally, that still points to a failure inside this valve assembly, and replacing the complete unit is the standard repair. Should I replace the fill hoses while I'm in there? It's a good idea. The fill hoses connect right at the same point you'll already have exposed, wear on a similar timeline as the valve, and are a common source of slow leaks that get blamed on the valve. Since you're already accessing this area, replacing hoses that show any cracking, bulging, or stiffness saves you from repeating the disassembly later. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the solenoid design, flow rate, and mounting configuration of the original W10599356 / W10509710 valve used in compatible Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore front-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO Washer Replacement Part XPARTCO 5220FR2075V Washer Water Valve Replaces 5221ER1003M Three-solenoid, DC12V water inlet valve assembly for select LG-built front-load washing machines. Product Overview The XPARTCO 5220FR2075V Washer Water Inlet Valve controls the flow of water entering compatible front-load washing machines. When energized by the washer control, the valve opens the required water path and directs water through the dispenser and into the tub. This is a new XPARTCO aftermarket replacement part designed to replace compatible LG inlet valve assemblies, including part number 5221ER1003M. Quick Answer XPARTCO 5220FR2075V is a three-solenoid, DC12V washer water inlet valve for select LG and LG-built Kenmore front-load washers. It replaces 5221ER1003M. Verify the complete washer model number, valve configuration, electrical connectors, and hose outlets before ordering. Common Problems This Part May Fix Washer does not fill with water Slow or restricted water filling Water continues entering after the washer is turned off Leaking from the inlet-valve area Incorrect water flow through the dispenser IE or another water-inlet-related error One or more valve solenoids do not open Replaces and Cross-References 5220FR2075V, ALG312873, AP7003066, PD00074485, PS16544738, 5221ER1003M, AP6334246, 4869495, ALG51888, EAP12579227, PD00050119, PS12579227 Cross-reference numbers help identify the compatible component. XPARTCO is an aftermarket replacement brand and is not manufactured by LG. Compatibility Designed for select LG and LG-built Kenmore front-load washers that specify 5220FR2075V, 5221ER1003M, or an approved equivalent. Compatible model examples associated with this valve family.  Important: This is only a partial compatibility list. LG water valves can look nearly identical while using different voltages, solenoid counts, mounting tabs, connectors, or outlet arrangements. Confirm the full washer model and original valve number before purchase. Key Features High-quality XPARTCO aftermarket replacement Replaces LG valve number 5221ER1003M DC12V, Three-solenoid inlet valve design Controls water entering the washer Directs water through the dispenser system Threaded inlet connection for the supply hose Designed for select LG-built front-load washers Product Specifications XPARTCO Part Number 5220FR2075V Replaces 5221ER1003M Brand XPARTCO Part Type Washer Water Inlet Valve Assembly, DC12V, 3 solenoid. Condition New Part Quality Aftermarket Replacement Valve Configuration Three Solenoids, DC12V Application Front-Load Washing Machine Included One Water Inlet Valve Assembly Installation Notes Unplug the washer and close both water-supply valves. Disconnect the inlet hose and prepare for residual water. Remove the washer top panel according to the appliance service procedure. Photograph the electrical connectors and outlet-hose locations before disconnecting them. Release the wire connectors, hose clamps, and mounting screws from the original valve. Install the replacement valve in the same orientation and reconnect every hose and wire. Open the water supplies slowly, check for leaks, restore power, and test the washer. Diagnostic tip: Confirm that the household water valves are open, inlet hoses are not kinked, and the inlet screens are not clogged before replacing the valve. Frequently Asked Questions Is XPARTCO 5220FR2075V a Genuine OEM LG part? No. It is an XPARTCO aftermarket replacement designed for compatible LG-built washers. What does the water inlet valve do? It opens and closes electrically to control water entering the washer and directs water through the dispenser system. Does this valve replace 5221ER1003M? Yes, this XPARTCO valve is sold as a replacement for 5221ER1003M on compatible washer models. Can a bad inlet valve cause an IE error? Yes. A failed solenoid, restricted valve, clogged inlet screen, or water-supply problem can cause slow filling or an inlet-related error. Will this fit every LG washer? No. Confirm the complete model number and compare the original valve number, connectors, mounting points, and hose outlets before ordering. Shop With Confidence Verify your washer model and original valve number before ordering. Our compatibility support team can help determine whether XPARTCO 5220FR2075V is correct for your appliance. XPARTCO Replacement PartFast U.S. ShippingCompatibility SupportSecure Checkout

Read more less

XPARTCO W10581874 Washer Drain Pump – Replaces WPW10581874 – Compatible with Whirlpool, Maytag & Kenmore Washers Product Description Restore proper water drainage and dependable washer performance with the XPARTCO W10581874 Washer Drain Pump. This high-quality aftermarket replacement pump removes wastewater during drain and spin cycles to prevent standing water and incomplete washes. A faulty drain pump can cause slow draining, loud humming or grinding noises, water remaining in the tub, or cycle interruptions. Replacing it with this reliable XPARTCO pump helps ensure smooth operation and restores efficient washing performance at a cost-effective price. XPARTCO offers trusted aftermarket appliance parts engineered to match original fit and function. Replaces Part Numbers WPW10581874, W10581874, 3449735, PD00028019, EAP10056668, AP6023189, PS11756530. Compatibility This replacement washer drain pump fits select Whirlpool, Maytag, Kenmore (Whirlpool-manufactured), Amana, Estate, and Roper washers. Common compatible models include (but are not limited to): Whirlpool WTW5000DW Maytag MVWB765FW Kenmore 110.25132411 Always verify your washer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM fit and drainage performance 💧 Efficient Water Removal – Restores proper draining during cycles 🔇 Quiet, Smooth Operation – Helps eliminate excessive pump noise 💪 Durable Motor & Housing – Built for long service life 💰 Cost-Effective Repair – Affordable alternative to OEM drain pumps 📐 Product Specification Part Number: W10581874 Component Type: Washer Drain Pump Voltage: 120V AC Mounting: Direct-fit, bolt-on installation Application: Washer drain and spin system Quality Level: Aftermarket replacement (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver, pliers ⚠️ Safety First: Unplug the washer and shut off the water supply before servicing. Basic Steps: Disconnect washer power and water supply. Access the drain pump from the bottom or rear of the washer. Remove hoses and electrical connectors. Remove mounting screws and remove the old pump. Install the new XPARTCO W10581874 drain pump. Reconnect hoses and wiring, reassemble panels, and restore power. Run a test cycle to confirm proper draining. ⏱️ Time Required: 25–35 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Aftermarket Appliance Parts 🔄 30-Day Return Policy Restore proper washer draining and prevent water buildup — Add to Cart Now for a dependable, budget-friendly repair!

Read more less

XPARTCO WH11X34742 (OE) Washer Drain Pump – Compatible with GE & Hotpoint Washers Product Description Restore proper water drainage and dependable washer performance with the XPARTCO WH11X34742 (OE) Washer Drain Pump. This OE (Original Equipment) replacement is manufactured to match original factory design and performance specifications, ensuring efficient water removal during drain and spin cycles. A failing drain pump can cause standing water, slow draining, excessive noise, or cycle interruption. Replacing it with this OE-spec XPARTCO pump helps restore smooth operation while offering a more cost-effective alternative to Genuine OEM parts. XPARTCO OE parts are built to match original fit and function while maintaining affordability. Replaces Part Numbers WH11X34742, WH01X28078, PD00076830, EAP16729517, AP7192541, PS16729517 Compatibility This OE washer drain pump fits select GE and Hotpoint top-load washers. Common compatible models include (but are not limited to): GE GTW335ASNWW, GTW465ASNWW Hotpoint HTW240ASKWS Always verify your washer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 OE (Original Equipment) Replacement – Matches original factory specifications 💧 Efficient Water Removal – Restores proper draining performance 🔇 Quiet Operation – Reduces humming or grinding noises 💪 Durable Motor & Housing – Designed for long service life 💰 Cost-Effective Alternative – OE quality without Genuine OEM pricing 📐 Product Specification Part Number: WH11X34742 Component Type: Washer Drain Pump Voltage: 120V AC Mounting: Direct-fit, bolt-on installation Application: Washer drain and spin system Quality Level: OE (Original Equipment) – not Genuine OEM 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver, pliers ⚠️ Safety First: Unplug the washer and shut off the water supply before servicing. Basic Steps: Disconnect washer power and water supply. Access the drain pump from the bottom or rear of the washer. Remove hoses and electrical connectors. Remove mounting screws and remove the old pump. Install the new XPARTCO WH11X34742 (OE) drain pump. Reconnect hoses and wiring, reassemble panels, and restore power. Run a test cycle to confirm proper draining. ⏱️ Time Required: 25–35 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted OE Appliance Parts 🔄 30-Day Return Policy Restore reliable washer draining with confidence — Add to Cart Now for a dependable OE-spec repair!

Read more less

XPARTCO 137221600 Washer Drain Pump The XPARTCO 137221600 is an aftermarket replacement washer drain pump compatible with a wide range of Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Kenmore, Tappan, and Westinghouse front-load washers — including popular Affinity series and washer-dryer combo models. The drain pump is mounted at the base of the washer and is responsible for evacuating the wash and rinse water from the tub through the drain hose at the end of each cycle. When the drain pump fails, the washer can't drain — leaving clothes soaking wet, water pooling in the tub, and the wash cycle unable to advance to spin. Common failure symptoms include humming without pumping (blocked or seized impeller), leaks from the pump housing, loud grinding or clicking noises, and complete pump silence when a drain cycle should be running. Rated 120V AC, 60Hz, 85W, 1.25A. Based on the Askol M65 design, with a firmly attached red flapper to prevent drain backflow into the tub. Constructed from strong, durable plastic to resist cracking and leaking through many years of cycling. Package includes the drain pump, mounting base, and mounting screw. This part directly replaces 137108100, 137151800, 137151800KITK, 131724000, 134051200, 134740500, 134740800, 2754548, ER137108100, TJ137108100, EAP7783938, LP1600, BPX401-72J, AP5684706, and PS7783938. Important: before installing the new pump, clean any lint or debris from the rubber boot, verify the drain hose is clear and properly fastened, and check the pump filter for blockage — installing a new pump on a system with the underlying blockage will not resolve the drainage problem. Installs in 30–60 minutes with basic hand tools. Quick Answer The XPARTCO 137221600 Washer Drain Pump fixes Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Kenmore, Tappan, and Westinghouse front-load washers that won't drain, leave clothes soaking wet, are noisy or humming during the drain cycle, or display an E11 error code. 120V AC, 60Hz, 85W, 1.25A. Askol M65 design with red backflow flapper. Kit includes pump + mounting base + screw. Replaces 137108100, 137151800, 137151800KITK, 131724000, 134051200, 134740500, 134740800, 2754548, ER137108100, TJ137108100, EAP7783938, LP1600, BPX401-72J, AP5684706, PS7783938. Common Problems This Part Fixes Washer not draining — pump failed to remove water at the end of the wash or rinse cycle Clothes left soaking wet at the end of the cycle — no drain, so no spin can start Water leaking from the bottom of the washer — cracked pump housing or failed seal Loud humming noise but no water flowing — pump motor running against a seized impeller or blockage Grinding, clicking, or unusual noises during the drain cycle E11 error code displayed on the control panel (drain fault) Washer pumps but won't spin — drain cycle can't complete, blocking spin Cycles taking much longer than normal as the washer tries to drain Pump silent during drain — motor windings open or electrical fault Impeller broken, cracked, or missing pieces after opening the pump Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This drain pump directly replaces the following OEM and cross-reference part numbers: 137221600, 131724000, 134051200, 134740500, 137108100, 137151800, 137151800KITK, 2754548, TJ137108100, ER137108100, PD00000118, EAP7783938, BPX401-72J, AFR14249, AP5684706, PS7783938, Also replaces GE WH23X10041, 2119312, WH23X10009, WH23X10017, WH23X10031, WH23X10034, AH3502779, EA3502779, AP5324214, PS3502779. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drain pump is compatible with select front-load washers and washer-dryer combos from the following brands: Frigidaire front-load washers — Affinity series (FAFW3001LW3, FAFW3801LW3 and related), FEX831FS2/FS4, FTF2140ES1, FWS445RFS2, FWX445RFS3 series Frigidaire front-load washers — ATF6000ES1, ATF8000FS1, ATFB6700FS0 series Frigidaire front-load washers — GLTF2940ES3, GLTF2940FS1 and related GLTF series Frigidaire washer-dryer combos — CWS3600AS1 and related Electrolux front-load washers — select models Crosley front-load washers — select models Gibson front-load washers — select models Kelvinator front-load washers — select models Kenmore / Sears front-load washers — select Frigidaire-built models (41744052400, 41744052401, 41744052500, 41744082500, 41748102700, 41748106700, 41748116700, 41790812995 and related 417-series) Tappan front-load washers — select models Westinghouse front-load washers — select models Note: The redesigned 137221600 may look slightly different from your original (e.g., white or gray housing vs. original black), but functions identically. Ensure proper orientation and flapper alignment during installation. Always verify your appliance model number before ordering. Key Features Aftermarket replacement built to OEM-equivalent quality standards Drain pump — removes water from the washer tub through the drain hose at the end of the wash and rinse cycles Resolves "won't drain," "won't spin," "wet clothes," "E11 error," and "humming pump" symptoms 120V AC, 60Hz, 85W, 1.25A — correct electrical specifications for compatible Frigidaire-platform washers Askol M65 design with red backflow flapper to prevent water from flowing back into the tub Strong, durable plastic construction resistant to cracking and leaking Kit includes: 1x drain pump, 1x mounting base, 1x mounting screw Replaces 15+ OEM and cross-reference part numbers including 137108100, 137151800, 131724000, 134051200, 134740500, 134740800, AP5684706, and PS7783938 Compatible with Frigidaire (Affinity, FEX, FTF, FWS, FWX, ATF, ATFB, GLTF, CWS series), Electrolux, Crosley, Gibson, Kelvinator, Kenmore (417-series), Tappan, and Westinghouse front-load washers and washer-dryer combos DIY repair — installs in 30–60 minutes with basic hand tools Product Specifications Part Number XP137221600 Part Type Washer Drain Pump Condition Aftermarket Replacement Application Front-Load Washers and Washer-Dryer Combos (Frigidaire/Electrolux platform) Voltage 120V AC Frequency 60 Hz Wattage 85W Amperage 1.25A Design Askol M65 with red backflow flapper Material Durable plastic Includes 1x Drain Pump, 1x Mounting Base, 1x Mounting Screw Error Codes Resolved E11 (drain fault) Compatible Brands Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Kenmore, Tappan, Westinghouse Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting — Wear Work Gloves — Check for Blockage First Disconnect power at the outlet or breaker and shut off both water supplies at the wall before beginning. Wear work gloves to protect your hands — pump components can have sharp edges. Have towels ready — residual water remains in the pump housing and hoses. Important: before replacing the pump, check for the underlying cause of the drain problem. Inspect the pump filter (accessible on many models via the lower front kick panel), the drain hose for kinks, and the rubber boot at the bottom of the tub for lint, coins, buttons, or other debris — installing a new pump on a system with an unresolved blockage will not fix the drain problem. Remove the appropriate access panel (typically the rear or front lower kick panel — model-dependent) to expose the pump. Photograph the wire harness and hose connections before disconnecting. Disconnect the electrical wire connectors from the pump motor. Squeeze the hose clamps with pliers and slide them back to release the tub-to-pump hose and the pump-to-drain-hose from the pump. Remove the 2 mounting screws holding the pump to its base and lift the old pump out. Clean any residual debris from the rubber boot, hoses, and pump filter area. Install the new 137221600 pump using the included mounting base and screw. Reconnect the hoses with the clamps, orient the red backflow flapper correctly, and reconnect the electrical connectors. Reinstall the access panel, restore water and power, and run a rinse cycle to test drainage and check for leaks at all connections. Tools needed: Phillips screwdriver, needle-nose pliers, channel-lock pliers, small flathead screwdriver, towel, work gloves. Frequently Asked Questions My washer won't drain — is it always the pump? Not always. Before replacing the pump, check for these common causes: 1) Clogged pump filter — most Frigidaire front-load washers have a filter accessible via the lower front kick panel; coins, buttons, lint, and small items can block it. 2) Kinked or clogged drain hose — inspect the entire drain hose from the pump to the wall standpipe or sink. 3) Blocked rubber boot — small items can get stuck between the tub and the pump inlet. 4) Failed lid lock/door switch — if the washer doesn't detect a locked door, it won't run the drain cycle. If all of these check out and the pump still isn't draining (or is humming without moving water), the pump has failed and this is the correct repair. What is the E11 error code on my Frigidaire washer? E11 on Frigidaire and Electrolux front-load washers indicates a drain fault — the control board is not detecting successful drainage within the expected time. Common causes are a failed drain pump, a clogged pump filter, a kinked or clogged drain hose, or debris blocking the impeller. If you've verified the filter and hose are clear but the code persists, replacing the 137221600 drain pump typically resolves it. If the code returns after replacement, check the wire harness between the pump and the control board. Does the pump come with everything I need for installation? Yes — the 137221600 (OE) package includes the drain pump itself, a mounting base, and a mounting screw. This is everything you need for the pump replacement itself. However, you should reuse the original hose clamps and hoses from your old pump (they should still be in good condition). If you find that the rubber boot at the base of the tub is cracked, hardened, or torn during the repair, that's a separate part that would need to be ordered — inspect it before completing the reinstallation. The new pump looks different from my old one — is it the right part? Very likely, yes. The 137221600 has been through several revisions over its production history — some housings are black, others white or gray, and the exact shape can vary slightly across production runs. As long as the mounting bolt pattern, hose inlet/outlet sizes, and electrical connector are the same, and the specs match (120V, 60Hz, 85W, Askol M65 design), the pump will function identically to your original. During installation, focus on correct orientation and flapper alignment — the flapper (red) must be positioned so it opens outward toward the drain hose direction to prevent backflow. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Frigidaire/Electrolux OEM part, but is manufactured to match the electrical specifications (120V AC, 60Hz, 85W, 1.25A), Askol M65 design, red backflow flapper, dimensions, and drain pump function of the original 137221600 used in compatible Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Kenmore, Tappan, and Westinghouse front-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WH23X27419 Washer Drain Pump – Compatible with GE, Haier & Hotpoint Washers Product Description Restore proper water drainage and reliable washer performance with the XPARTCO WH23X27419 Washer Drain Pump. This high-quality aftermarket replacement pump is designed to efficiently remove water from the washer during drain and spin cycles. A worn or failing drain pump can cause standing water, slow draining, loud humming or grinding noises, or cycle interruptions. Replacing it with this dependable XPARTCO pump helps ensure smooth operation and prevents water-related issues. XPARTCO offers cost-effective aftermarket appliance parts built to OEM-equivalent fit and performance standards. Replaces Part Numbers WH23X27419, WD-5470-09, 4588221, PD00053097, EAP12343437, AP6328341, PS12343437. Compatibility This replacement washer drain pump fits select GE, Haier and Hotpoint top-load washers. Example compatible models include (but are not limited to): GE GTW465ASNWW, GTW485ASJWS Hotpoint HTW240ASKWS Haier HLP22P: 11LBS DOUBLE DRIVE FUZZ, Haier RWT150AW, RWT150AW, Haier RWT350AW 3.1 CUBIC FEET TOP LOAD AGITATOR WASHER, WHITE Haier XQB5010A, Haier GWT460AW GWT460AW: AMERICA/HAIER/10KG Haier XQB6091AF XQB60-91AF:PORTABLE WASHER-13. Haier XQB6091BF XQB60-91BF:13.2 LB HAND WASH W Haier RWT360BW 3.0 CU. FT. CAPACITY TOP-LOAD WASHER Haier GWT460BW 3.2 CU. FT. CAPACITY HIGH-EFFICIENCY WASHER Haier BRW2, PCX-30L V12624 GWT450AW GWT450AW Always verify your washer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM fit and pumping performance 💧 Efficient Water Removal – Restores proper draining during cycles 🔇 Quiet, Smooth Operation – Helps eliminate pump noise issues 💪 Durable Motor & Housing – Built for long-term reliability 💰 Cost-Effective Repair – Affordable alternative to OEM drain pumps 📐 Product Specification Part Number: WH23X27419 Component Type: Washer Drain Pump Voltage: 120V AC Mounting: Direct-fit, bolt-on installation Application: Washer drain and spin system Quality Level: Aftermarket replacement (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver, pliers ⚠️ Safety First: Unplug the washer and shut off the water supply before servicing. Basic Steps: Disconnect washer power and water supply. Access the drain pump from the bottom or rear of the washer. Remove hoses and electrical connectors. Remove mounting screws and take out the old pump. Install the new XPARTCO WH23X27419 drain pump. Reconnect hoses and wiring, reassemble panels, and restore power. Run a test cycle to confirm proper draining. ⏱️ Time Required: 25–35 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Aftermarket Appliance Parts 🔄 30-Day Return Policy Restore proper washer draining and prevent water buildup — Add to Cart Now for a dependable, budget-friendly repair!

Read more less

WH23X27419 Washer Genuine OEM Drain Pump – Compatible with GE, Haier & Hotpoint Washers Product Description Restore proper draining and reliable washer performance with the WH23X27419 Washer Genuine OEM Drain Pump. This original equipment manufacturer (OEM) drain pump is engineered by the manufacturer to exact specifications, ensuring proper water removal during drain and spin cycles. A failing drain pump can cause standing water, slow draining, loud noises, or error codes. Replacing it with this genuine OEM pump helps return your washer to factory-level performance and reliability. This part is a Genuine OEM component, designed for exact fit, correct electrical ratings, and long-term durability. Replaces Part Numbers WH23X27419, WD-5470-09, 4588221, PD00053097, EAP12343437, AP6328341, PS12343437. Compatibility This Genuine OEM washer drain pump fits select GE and Hotpoint top-load washers. Example compatible models include (but are not limited to): GE GTW465ASNWW, GTW485ASJWS Hotpoint HTW240ASKWS Haier HLP24E, RWT350AW, GWT450AW, XQB6091AF, Xqb60-91Af, HLP28E, GWT480BW Always verify your washer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🏭 Genuine OEM Part – Manufactured to original factory specifications 💧 Efficient Water Removal – Restores proper draining and spin performance 🔇 Quiet Operation – Reduces grinding or humming noises 💪 OEM-Grade Motor & Housing – Built for long service life 🔧 Exact Fit & Plug-and-Play Installation – No modifications required 📐 Product Specification Part Number: WH23X27419 Component Type: Washer Drain Pump Voltage: 120V AC Mounting: Direct-fit, bolt-on installation Application: Washer drain and spin system OEM Status: Genuine OEM 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver, pliers ⚠️ Safety First: Unplug the washer and shut off the water supply before servicing. Basic Steps: Disconnect washer power and water supply. Access the drain pump from the bottom or rear of the washer. Remove hoses and electrical connectors. Remove mounting screws and take out the old pump. Install the new WH23X27419 Genuine OEM drain pump. Reconnect hoses and wiring, reassemble panels, and restore power. Run a test cycle to confirm proper draining. ⏱️ Time Required: 25–35 minutes 📦 Shop With Confidence 🏭 Genuine OEM Appliance Part 🚚 Free Shipping on All Orders 🔄 30-Day Return Policy Restore factory-level washer performance and reliable draining — Add to Cart Now with confidence!

Read more less

XPARTCO WL49X20360 Washer Motor Speed Sensor Kit – Compatible with GE & Hotpoint Washers Product Description Restore accurate motor speed detection and reliable washer operation with the XPARTCO WL49X20360 Washer Motor Speed Sensor Kit. This high-quality aftermarket replacement kit monitors the washer motor’s rotation speed and sends feedback to the control board for proper agitation and spin performance. A faulty speed sensor can cause error codes, no spin, irregular agitation, or cycle interruptions. Replacing it with this XPARTCO kit helps restore smooth operation and consistent wash cycles. XPARTCO is a trusted aftermarket brand offering appliance replacement parts built to OEM-equivalent specifications at a cost-effective price. Replaces Part Numbers WL49X20360, WH12X10515, 3031241, PD00025952, EAP8768455, AP5803767, PS8768455. Compatibility This replacement washer motor speed sensor kit fits select GE and Hotpoint washers. Example compatible models include (but are not limited to): GE GTW465ASNWW, GTW485ASJWS Hotpoint HTW240ASKWS Always verify your washer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement Kit – Matches OEM fit and signal performance ⚙️ Accurate Motor Speed Feedback – Ensures proper agitation and spin control 🛠️ Direct-Fit Design – No modifications required 💪 Durable Electronic Components – Built for long-term reliability 💰 Cost-Effective Repair – Reliable alternative to OEM sensor kits 📐 Product Specification Part Number: XPWL49X20360 Component Type: Washer Motor Speed Sensor Kit Function: Motor rotation and speed detection Application: Washer drive motor feedback system Includes: Speed sensor and mounting hardware (as applicable) Quality Level: Aftermarket replacement (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver ⚠️ Safety First: Unplug the washer before servicing to avoid electrical shock. Basic Steps: Disconnect washer power. Access the motor area from the bottom or rear of the washer. Locate and disconnect the old motor speed sensor. Remove mounting hardware and replace with the new XPARTCO WL49X20360 sensor. Reconnect wiring and secure the sensor. Reassemble panels, restore power, and run a test cycle. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Aftermarket Appliance Parts 🔄 30-Day Return Policy Restore accurate washer motor control and dependable performance — Add to Cart Now for a reliable, budget-friendly repair!

Read more less

DC62-00311F Washer Genuine OEM Water Valve – Compatible with Samsung & Kenmore Washers Product Description Restore proper water flow and dependable washer operation with the DC62-00311F Washer Genuine OEM Water Valve. This factory-approved inlet valve precisely controls water entering the washer during fill cycles. A defective valve may cause no-fill issues, slow filling, water leaks, or error codes. Installing this Genuine OEM water valve ensures exact fit, correct water pressure, and long-lasting performance as designed by the manufacturer. Replaces Part Numbers DC62-00311F, PD00043649, EAP11719654, AP5966624, 3992244, PS11719654. Compatibility This Genuine OEM washer water inlet valve fits select Samsung and Kenmore (Samsung-manufactured) washers. Example compatible models include (but are not limited to):Samsung WF203ANS, WF206ANS, WF209ANSKenmore 592.49003, 592.49005 Always verify your washer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🧩 Genuine OEM Replacement – Factory-certified for exact fit and performance 💧 Accurate Water Control – Ensures proper fill levels during wash cycles 🔧 Durable Solenoid Construction – Designed for reliable long-term use 🛠️ Direct-Fit Installation – No modifications required 🛡️ Fixes Common Issues – Resolves no-fill, slow fill, leaking, or error codes 📐 Product Specification Part Number: DC62-00311F Component Type: Washer Water Inlet Valve Voltage: 120V AC Water Connections: Hot & Cold Material: OEM-grade reinforced plastic with metal solenoids Mounting: Rear cabinet direct-fit Compliance: Genuine OEM certified 🛠️ Installation Notes Tools Needed: Phillips screwdriver, pliers, towel or shallow pan ⚠️ Safety First: Unplug the washer and shut off the water supply before servicing. Steps: Disconnect power and turn off water supply. Remove the rear access panel. Disconnect inlet hoses and wiring harness from the old valve. Remove mounting screws and take out the old valve. Install the new DC62-00311F water valve and secure it. Reconnect hoses and wiring, restore water and power, and test for leaks. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Genuine OEM Replacement Part 🔄 30-Day Return Policy Restore proper washer filling with confidence — Add to Cart Now for a factory-quality repair!

Read more less

DC62-30314V Washer Genuine OEM Water Valve – Compatible with Samsung & Kenmore Washers Product Description Restore proper water filling and dependable washer performance with the DC62-30314V Washer Genuine OEM Water Valve. This factory-approved inlet valve precisely controls hot and cold water flow into the washer during fill cycles. A failing water valve can cause no-fill issues, slow filling, error codes, or poor wash results. Installing this Genuine OEM valve ensures exact fit, correct water pressure, and long-lasting reliability. Replaces Part Numbers DC62-30314V, PD00054103, EAP11719664, AP5966634, 3992464, PS11719664. Compatibility This Genuine OEM washer water inlet valve fits select Samsung and Kenmore (Samsung-manufactured) washers. Example compatible models include (but are not limited to):Samsung WF45R6100AW, WF42H5000AWKenmore 592.49045, 592.49303 Always verify your washer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🧩 Genuine OEM Replacement – Factory-certified for exact fit and performance 💧 Accurate Water Flow Control – Ensures proper filling during wash cycles 🔧 Durable Solenoid Design – Built for consistent operation and long service life 🛠️ Direct-Fit Installation – No modifications required 🛡️ Fixes Common Issues – Resolves no-fill, slow fill, error codes, or weak water flow 📐 Product Specification Part Number: DC62-30314V Component Type: Washer Water Inlet Valve Voltage: 120V AC Water Connections: Hot & Cold Material: OEM-grade reinforced plastic with metal solenoids Mounting: Rear cabinet direct-fit Compliance: Genuine OEM certified 🛠️ Installation Notes Tools Needed: Phillips screwdriver, pliers, towel or shallow pan ⚠️ Safety First: Unplug the washer and shut off the water supply before servicing. Steps: Disconnect power and turn off water supply. Remove the rear access panel. Disconnect inlet hoses and wiring harness. Remove mounting screws and take out the old valve. Install the new DC62-30314V valve and secure it. Reconnect hoses and wiring, restore water and power, and test for leaks. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Genuine OEM Replacement Part 🔄 30-Day Return Policy Restore proper washer filling and reliable performance — Add to Cart Now for a factory-quality repair!

Read more less

WH03X36897 Washer Genuine OEM Mode Shifter Actuator – Compatible with GE & Hotpoint Washers Product Description Restore proper wash and spin operation with the WH03X36897 Washer Genuine OEM Mode Shifter Actuator. This factory-approved component shifts the washer between agitation and spin modes during the wash cycle. A failing mode shifter can cause the washer to agitate but not spin, spin improperly, make clicking noises, or display cycle errors. Replacing it with this Genuine OEM actuator ensures precise shifting, reliable performance, and correct cycle operation. Replaces Part Numbers WH03X36897, WH18X27186, AP7225424, PD00087767, EAP17626543, PS17626543 Compatibility This Genuine OEM mode shifter actuator fits select GE and Hotpoint top-load washers. Example compatible models include (but are not limited to):GE GTW335ASN1WW, GTW465ASN2WW, GTW485ASJ1WSHotpoint HTW240ASK6WS Always verify your washer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🧩 Genuine OEM Replacement – Factory-certified for exact fit and dependable operation 🔄 Accurate Mode Shifting – Properly switches between wash and spin cycles 🔇 Quiet, Smooth Operation – Reduces clicking or erratic shifting noises 💪 OEM-Grade Durability – Designed for long service life under repeated cycles 🛡️ Fixes Common Issues – Solves no-spin, improper agitation, or cycle errors 📐 Product Specification Part Number: WH03X36897 Component Type: Washer Mode Shifter Actuator Voltage: 120V AC Mounting: Direct-fit installation on transmission assembly Function: Controls agitation-to-spin shifting Compliance: Genuine OEM certified 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver ⚠️ Safety First: Unplug the washer before servicing to avoid electrical shock. Steps: Disconnect power and tilt the washer back for bottom access. Locate the mode shifter actuator near the transmission. Disconnect the wiring harness and remove mounting screws. Install the new WH03X36897 actuator and secure it in place. Reconnect wiring, return washer upright, and restore power. Run a test cycle to confirm proper shifting. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Genuine OEM Replacement Part 🔄 30-Day Return Policy Restore correct washer cycle operation — Add to Cart Now for a factory-quality repair!

Read more less