Today's Deals

Choice 6602-001655 Dryer Drum Belt  Drum Belt Replaces: 6602-001655, 6602-001314, 5PH2337, AP4373659, PS4133825. 5 Rib, 92" Description: This Belt is a replacement part is compatible with specific Samsung dryer models. The belt attaches to the motor pulley and spins the drum as the motor rotates. Over time, the belt can snap. This is due to general wear and tear, overloading, or excessive friction do to a damaged felt seal. Whenever the dryer belt breaks, the drum will not rotate and would need to be replaced. This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

XPARTCO 6602-001655 Dryer Drum Belt The XPARTCO 6602-001655 is an aftermarket replacement dryer drum belt compatible with select Samsung and Kenmore dryers. The drum belt wraps around the outside of the dryer drum, loops around the motor pulley and idler pulley, and drives the drum to rotate during every drying cycle. Without a functioning belt, the drum cannot spin and clothes will not tumble or dry. Made from premium neoprene rubber reinforced with polyester cords, this 5-rib belt measures 92 inches long x 5/16 inch wide and is built to resist cracking, stretching, and wear under the high heat and repeated tension cycles of daily dryer use. It is a direct drop-in replacement for OEM part numbers 6602-001655 and 6602-001314, and installs in 30–45 minutes with basic hand tools. Quick Answer The XPARTCO 6602-001655 Dryer Drum Belt fixes dryers where the drum is not spinning, clothes are not tumbling, or a thumping/squealing noise is coming from the dryer during operation. It drives the drum via the motor and idler pulleys. Compatible with select Samsung and Kenmore dryers. Measures 92" L x 5/16" W with 5 ribs and 4 grooves. Common Problems This Part Fixes Dryer drum not spinning — motor runs but drum stays still Clothes not tumbling during the drying cycle Thumping, squealing, or slapping noise during operation Dryer runs but produces no heat because drum is stationary Visible broken or frayed belt pieces found inside the dryer cabinet Dryer shuts off shortly after starting due to drum not rotating Replaces Part Numbers This drum belt directly replaces the following OEM and cross-reference part numbers: 6602-001655, 6602-001314, 5PH2337, LB1655, ASM874658, PD00002012, EAP2407938, AP4373659, PS4133825. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drum belt is compatible with select dryers from the following brands: Samsung dryers (gas and electric) Kenmore / Sears dryers (select models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Drives the dryer drum via the motor pulley and idler pulley for smooth, consistent tumbling every cycle 92" length x 5/16" width — 5-rib, 4-groove design for a secure, slip-free grip on the pulleys Made from premium neoprene rubber with polyester cord reinforcement — resists cracking, stretching, and heat damage Direct replacement for OEM part numbers 6602-001655 and 6602-001314 — no modification required Aftermarket replacement built to OEM-equivalent quality standards DIY-friendly repair — installs in 30–45 minutes with basic hand tools Often replaced together with the idler pulley (DC93-00634A) and drum rollers (DC97-16782A) for a complete drum drive repair Product Specifications Part Number 6602-001655 Part Type Dryer Drum Drive Belt Condition Aftermarket Replacement Application Gas and Electric Dryers Length 92 inches Width 5/16 inch Height 1/8 inch Ribs 5 ribs, 4 grooves Material Neoprene rubber with polyester cord reinforcement Color Black Compatible Brands Samsung, Kenmore Often Replaced With DC93-00634A Idler Pulley, DC97-16782A Drum Rollers Installation Notes ⚠️ Safety First — Unplug Dryer Before Starting Unplug the dryer from the power source (and shut off the gas supply for gas dryers) before beginning any repair. To access the drum belt, remove the top panel and front panel of the dryer. Lift the drum out of the cabinet, remove the old belt, and loop the new 6602-001655 belt around the drum with the ribbed side facing inward. Route the belt slack around the idler pulley and motor pulley — consult your dryer's service manual or a model-specific video for the correct belt path around the pulleys. Reassemble the front panel, top panel, and restore power before running a test cycle. Tip: While the drum is out, this is an ideal time to also inspect and replace the idler pulley and drum support rollers if worn. Tools needed: Phillips screwdriver, putty knife or flat pry tool. Frequently Asked Questions Will the 6602-001655 fit my Samsung or Kenmore dryer? This belt is compatible with select Samsung and Kenmore dryers. Use the model search above to verify your model number, or contact our support team before ordering. What does the dryer drum belt do? The drum belt wraps around the outside of the dryer drum and connects to the motor pulley and idler pulley. As the motor spins, it drives the belt which causes the drum to rotate, tumbling your clothes through the heated air to dry them. A broken or worn belt means the drum cannot spin. How do I know if my drum belt is broken? The most obvious sign is that the dryer motor runs and you can hear it humming, but the drum does not spin. You may also hear a thumping or slapping sound if the belt is slipping or partially broken. Opening the dryer cabinet and visually inspecting the belt will confirm if it is broken, frayed, or stretched. Should I replace the idler pulley and drum rollers at the same time? Yes — since you need to disassemble the dryer to replace the belt anyway, it is highly recommended to also inspect and replace the idler pulley (DC93-00634A) and drum support rollers (DC97-16782A) at the same time. These parts wear at a similar rate and replacing all three together prevents having to disassemble the dryer again in the near future. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is made from premium neoprene rubber with polyester cord reinforcement to match the dimensions and performance of the original belt. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

279570 Genuine OEM Whirlpool Dryer Door Catch Kit The 279570 is a Genuine OEM Whirlpool dryer door catch and strike kit compatible with a wide range of Whirlpool, Kenmore, Roper, Estate, Amana, Crosley, Inglis, KitchenAid, Maytag, and Admiral dryers. The door catch is the spring-clip mechanism on the dryer door that snaps over the door strike to hold the door firmly closed during operation, activating the door switch so the dryer can run. When the catch breaks, wears out, or loses tension, the door will not stay closed, the door switch will not be activated, and the dryer will either not start or will stop mid-cycle. The strike is the corresponding post or tab on the dryer cabinet that the catch engages. This Genuine OEM kit includes three color-coded door catches of different tensions and two metal door strikes, plus one screw. Because the tension of the catch must match the original, Whirlpool includes three options in the kit — each is color-coded and numbered on the back. Refer to identify which catch is correct for your model. The kit directly replaces a very large list of older cross-reference numbers including 279570VP, 3493, 2003, 8208, 279280, 279337, 696144, 693717, AP3094183, PS334230, and dozens more. Installs in under 15 minutes with a Phillips screwdriver. Quick Answer The 279570 Genuine OEM Whirlpool Dryer Door Catch Kit fixes dryers where the door won't stay closed, pops open mid-cycle, or won't activate the door switch to start. Kit includes 3 color-coded catches (different tensions), 2 metal strikes, 1 screw. Use the catch that matches your original. Genuine OEM. Compatible with Whirlpool, Kenmore, Roper, Estate, Amana, Crosley, Inglis, KitchenAid, Maytag, and Admiral dryers. Installs in under 15 minutes. Common Problems This Kit Fixes Dryer door will not stay closed during the drying cycle Door pops open mid-cycle, stopping the dryer Dryer will not start — door switch not being activated by a worn or broken catch Door feels loose or does not click shut firmly when closed Door catch visibly cracked, broken, or missing Door strike bent or missing — door cannot engage the catch properly Dryer requires the door to be held or pushed closed to stay running Replaces Part Numbers This door catch kit directly replaces the following OEM and cross-reference part numbers: 279570, 14205029, 14205577, 14210022, 2003, 236876, 236877, 241282, 241890, 26000279570, 261847, 263067, 279280, 279337, 279469, 279570VP, 291949, 3390239, 3392538, 3398175, 342295, 347813, 3493, 4165234, 51651001, 51655001, 66021, 690081, 690082, 693717, 694343, 696144, 8208, 830751, 834767, 834813, 834943, 834944, AH334230, DE902, EA334230, EAP334230, FSP279570, AP3094183, AWP39897, PD00002346, PS334230. Contact our support team with your model number if you need confirmation before ordering. Compatibility This door catch kit is compatible with select dryers from the following brands: Whirlpool dryers (gas and electric) Kenmore / Sears dryers (Whirlpool-built models) Roper dryers Estate dryers Amana dryers Crosley dryers Inglis dryers KitchenAid dryers Maytag dryers Admiral dryers Important: This kit includes three catches with different spring tensions, color-coded and numbered on the back. You must use the catch that matches the tension of your original. Using the wrong tension catch may result in a door that is too hard to open or too easy to pop open. Key Features Genuine OEM kit manufactured by Whirlpool to factory specifications — guaranteed fit and performance Holds the dryer door closed and activates the door switch so the dryer can run safely Kit includes 3 color-coded door catches (different spring tensions), 2 metal door strikes, 1 screw Catches are color-coded and numbered on the back — use the one that matches your original. Plastic catches with metal strikes and metal screw — durable construction for long service life Consolidates a very large list of older Whirlpool-family door catch cross-reference numbers Compatible with 10 major appliance brands on the Whirlpool platform Quick DIY repair — installs in under 15 minutes with a Phillips screwdriver Product Specifications Part Number 279570 Part Type Dryer Door Catch and Strike Kit Condition Genuine OEM Application Gas and Electric Dryers Kit Includes 3 color-coded door catches (different tensions), 2 metal strikes, 1 screw Material Plastic catches / Metal strikes Color White / Silver Catch Selection Color-coded and numbered, Use the catch that matches your original Compatible Brands Whirlpool, Kenmore, Roper, Estate, Amana, Crosley, Inglis, KitchenAid, Maytag, Admiral Installation Notes ⚠️ Unplug Dryer Before Starting Disconnect power before beginning. using the wrong tension catch will result in incorrect door resistance. Open the dryer door and locate the old door catch on the inside of the door panel and the strike on the dryer cabinet opening. To remove the old catch: press the retaining tabs and pull the catch free from its slot, or unscrew the mounting screw. Install the correct new catch into the same position. To replace the strike: remove the old strike (typically held by a single screw) and install the new strike in the same position. Close the dryer door to confirm it latches firmly with a satisfying click. Restore power and run a short test cycle to confirm the door stays closed and the dryer operates normally. Tools needed: Phillips screwdriver; needle-nose pliers may help with catch removal on some models. Frequently Asked Questions Why does the kit include three different catches? Whirlpool used door catches with different spring tensions across its dryer lineup — a lighter catch on some models and a stiffer catch on others. To cover all compatible models in a single kit, Whirlpool includes three catches of different tensions, each color-coded and numbered on the back. It is important to use the correct one — using a catch with too little tension may allow the door to pop open, while a catch with too much tension may make the door difficult to open. Do I need to replace both the catch and the strike, or just one? It depends on which component has failed. The catch (the spring-clip on the door) is the more commonly replaced part — it wears out from repeated use faster than the strike. Inspect both: if the catch is cracked or has lost its spring tension, replace the catch. If the strike is bent, cracked, or missing, replace the strike. Since the kit includes both catches and strikes, you have everything needed for a complete repair. When in doubt, replacing both ensures the full latch system is renewed. My dryer will not start even after replacing the door catch — what else could it be? If the dryer still will not start after the catch is replaced, the door switch may also need to be tested. The door switch is the electrical component that the door catch activates when the door closes — if the switch itself is failed, replacing the catch alone will not restore function. Test the door switch (3406105 for most Whirlpool-family models) with a multimeter for continuity in both the open and closed positions. If the switch reads open in both positions or closed in both positions, it has failed and needs replacement. How is the 279570 different from the W11429587 dryer door catch? The 279570 is the door catch kit for older Whirlpool-family dryers — it includes multiple catches of different tensions and metal strikes because it covers a wide range of older models. The W11429587 is a single snap-in door catch for newer Whirlpool-family dryers (Cabrio and newer platform models). If your dryer is a newer model with a snap-in catch slot rather than a screw-mounted catch and strike, you likely need the W11429587. Verify your model number to confirm which part is correct. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM kit manufactured by Whirlpool to factory specifications. It is the exact same door catch and strike kit supplied by Whirlpool for compatible dryer service repairs — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 134511600 Washer Drive Belt Replaces WH07X10009 The XPARTCO 134511600 is an aftermarket replacement washer drive belt (V-belt) compatible with a wide range of Frigidaire, Electrolux, GE, Gibson, Crosley, Kenmore, Tappan, White-Westinghouse, and Kelvinator washing machines. The drive belt connects the drive motor to the washer's drive system, transferring power to spin the basket and drive the transmission during agitation and spin cycles. When the belt wears out, stretches, frays, or snaps, the washer motor runs but the tub doesn't spin or agitate — one of the most recognizable failure patterns in appliance repair. This is a universal-fit aftermarket belt that spans both the Frigidaire/Electrolux platform (134511600-series part numbers) and the GE platform (WH07X-series part numbers) — one physical belt covers both manufacturers' cross-referenced drive belt positions on compatible washers. V-belt profile, approximately 1/2" wide with a 31–32" circumference. It directly replaces 134511600, 134161100, 131686100, 131234000, 1156860, 145371, 3204418, F145371, F145371-000, AP3867042, AP3203734, AH1146950, EA1146950, PS1146950, PS960606, WH07X10009, WH07X10002, WH07X0113, WH7X10009, WH7X10002, WH7X113, AH960606, EA960606, and 1089279. Belt failures typically come from normal wear, stretching, fraying, or snapping due to overloading. Installs in 30–60 minutes with basic hand tools. Quick Answer The XPARTCO 134511600 Washer Drive Belt fixes Frigidaire, Electrolux, GE, Gibson, Crosley, Kenmore, Tappan, and White-Westinghouse washers where the motor runs but the tub won't spin or agitate, the washer makes squealing or burning-rubber smells, or the belt is visibly cracked, frayed, or snapped. V-belt, approximately 1/2" wide x 31–32" circumference. Universal-fit — spans both Frigidaire (134511600) and GE (WH07X10009) platforms. Replaces 134161100, 131686100, 131234000, 1156860, AP3867042, AP3203734, PS1146950, PS960606, WH07X10009, WH07X10002, WH7X113 and more. Common Problems This Part Fixes Washer motor runs but the tub won't spin — belt snapped or slipping Washer won't agitate — belt no longer driving the transmission Tub spins slowly or intermittently — belt worn, stretched, or glazed Loud squealing or screeching during the spin cycle — belt slipping on the pulleys Burning rubber smell during operation — belt slipping and overheating Belt visibly cracked, frayed, glazed, or stretched Belt broken completely — often found lying in the bottom of the cabinet Clothes coming out sopping wet because the spin cycle isn't working Washer stops mid-cycle when it should transition to spin Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This universal-fit washer drive belt directly replaces the following OEM and cross-reference part numbers across multiple brands: 134511600, 1156860, 131234000, 131686100, 134161100, 145371, 3204418, AH1146950, AP3867042, EA1146950, F145371, F145371-000, AFR14885, PD00000111, PS1146950, WH07X10009, WH07X0113, WH07X10002, WH7X10002, WH7X10009, WH7X113, AH960606, EA960606, AP3203734, PS960606. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This universal-fit drive belt is compatible with select washing machines from the following brands: Frigidaire washers — FLEB43RGS3, FLEB8200FS0, FLGB43RGS1, FLSE72GCS8, FLSG72GCSA, FWS223RFS0, FWS777GHS0, FWS933FS0, FWX233RES4, FWX645LBS4, FWXB45RGS0, FEZ831AS2 and related models Electrolux washers — select models on the Frigidaire platform GE washers and washer/dryer combo units — select models (WH07X10009 cross-reference) Crosley washers — CLCE500FW0, CLCE500FW1, CLCE500FW2, CLCG500FW0, CLCG500FW1, CLCG500FW3 and related models Gibson washers — select models Kelvinator washers — select models Tappan washers — select models White-Westinghouse washers — select models Kenmore / Sears washers — select Frigidaire-built and GE-built models Hotpoint and RCA washers — select GE-built models Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Universal-fit washer drive belt (V-belt) — replaces both Frigidaire/Electrolux (134511600-series) and GE (WH07X-series) OEM drive belts in a single aftermarket part Connects the drive motor to the washer's drive system, spinning the basket and driving the transmission Resolves "motor runs but tub won't spin," "won't agitate," "squealing," and "burning rubber smell" symptoms V-belt profile: approximately 1/2" wide with a 31–32" circumference Durable rubber construction engineered to resist stretching, cracking, and glazing under load Replaces 23+ OEM and cross-reference part numbers spanning Frigidaire, Electrolux, GE, and universal aftermarket catalogs Compatible with Frigidaire, Electrolux, GE, Gibson, Crosley, Kenmore, Tappan, White-Westinghouse, Kelvinator, Hotpoint, and RCA washers Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 30–60 minutes with basic hand tools Product Specifications Part Number 134511600 Also Replaces (GE-side) WH07X10009 Part Type Washer Drive Belt (V-Belt) — Universal Fit Condition Aftermarket Replacement Application Washing Machines (Frigidaire and GE platforms) Belt Profile V-belt Width Approximately 1/2" Circumference Approximately 31–32" Material Rubber Also Known As V-Belt Compatible Brands Frigidaire, Electrolux, GE, Gibson, Crosley, Kenmore, Tappan, White-Westinghouse, Kelvinator, Hotpoint, RCA Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting — Wear Work Gloves Disconnect the washer from all utilities — unplug it from the outlet (or shut off the breaker) and turn off the hot and cold water supplies — before beginning. Wear work gloves to protect your hands from sharp sheet metal edges inside the cabinet. Pull the washer away from the wall to give yourself room to work. Access the drive belt by removing the rear access panel or tilting/laying the washer to reach the underside — the specific procedure varies by model, so consult your appliance's service diagram. Photograph the belt routing before removing anything so you can match the path with the new belt. Remove any pieces of the old broken belt from around the motor pulley and the transmission/drive pulley, and clear out accumulated lint or debris. Inspect the pulleys while you're in there — if a pulley is rough, grooved, or wobbly, the new belt will wear out prematurely and the pulley should be addressed too. Route the new 134511600 belt around the drive motor pulley and the transmission pulley, following the same path as the original. Rotate the pulleys by hand a few full turns to confirm the belt seats correctly in the pulley grooves and rides smoothly without twisting or binding. Confirm proper belt tension — the belt should be snug with a small amount of deflection, not loose enough to slip or so tight that it stresses the bearings. Reinstall the access panel, restore water and power, and run a test cycle to confirm the tub agitates and spins normally. Tools needed: Phillips screwdriver, nut driver, socket/ratchet, work gloves. Frequently Asked Questions My washer motor runs but the tub won't spin — is the belt the problem? Almost certainly, yes. When you can hear the motor running (a hum or whir) but the tub stays still or barely turns, the drive belt has almost always snapped, slipped off its pulleys, or worn to the point where it can't grip. A quick check: unplug the washer, open the cabinet, and look for a belt lying loose in the bottom — a snapped belt is unmistakable. If the belt is still on the pulleys but glazed, cracked, or stretched, it's slipping rather than driving and needs replacement. Other symptoms that point to the belt: a squealing noise during spin, or a burning-rubber smell from the belt slipping and overheating against the pulleys. Does this really fit both Frigidaire AND GE washers? Yes — this is a genuine cross-brand part. The same V-belt design serves as a direct replacement for both the Frigidaire/Electrolux 134511600-series and the GE WH07X-series drive belts, and the two OEM catalogs are cross-referenced to each other through the 134161100 number. The belts share the same V-profile, width (approximately 1/2"), and circumference (31–32"), allowing a single aftermarket belt to function correctly in both platforms. Compatible models span Frigidaire's FLEB/FLGB/FLSE/FLSG/FWS/FWX series, GE washers and washer/dryer combos, plus Crosley, Gibson, Kelvinator, Tappan, White-Westinghouse, Kenmore, Hotpoint, and RCA models. Always verify your specific model number before ordering. What causes a washer drive belt to fail? The most common causes are normal wear and tear from continuous use, stretching over time (which reduces grip and causes slipping), fraying or cracking from age and repeated flexing, and snapping due to overloading the washer or improper installation. Chronic overloading is a big contributor — forcing the motor to drive an over-packed tub puts extreme stress on the belt. Belt failures can also be accelerated by a worn or seized pulley, which is why it's worth inspecting the motor and transmission pulleys whenever you replace the belt. If a pulley is rough, grooved, or wobbly, the new belt will wear out quickly against it. How tight should the new belt be? The belt should be snug in the pulley grooves with a small amount of deflection when you press on it — firm enough that it won't slip under load, but not so tight that it puts excess strain on the motor and transmission bearings. Most washers with a V-belt drive use a spring-loaded or adjustable motor mount to set tension automatically; if yours has an adjustment, follow your model's service specification. After installing, rotate the pulleys by hand a few full turns and confirm the belt tracks correctly in the grooves without twisting or riding up the sides. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Frigidaire, Electrolux, or GE OEM part, but is manufactured from durable rubber to match the V-belt profile, dimensions (approximately 1/2" wide x 31–32" circumference), and drive function of the original 134511600 and WH07X10009 washer drive belts used across compatible Frigidaire, Electrolux, GE, Gibson, Crosley, Kenmore, Tappan, White-Westinghouse, Kelvinator, Hotpoint, and RCA washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

5303281153 Dryer Rear Drum Bearing Kit - Compatible with Frigidaire, Electrolux, Kenmore, Gibson Dryers Product Description Keep your dryer running smoothly with the Replacement 5303281153 Dryer Rear Drum Bearing Kit. This Genuine OEM replacement kit, designed for select Frigidaire, Electrolux, Kenmore, Gibson, and other brand dryers, includes a bearing cup (131825900), ball shaft (131777700), ball bearing (5303281019), ball bearing retainer (5303281020), high-temperature lubricant, and mounting screws to support the drum’s rear for quiet, efficient rotation. It fixes issues like loud squeaking, grinding, or thumping noises, drum not tumbling, or marks on clothes due to misalignment. Note: Requires drum removal to access the bearing. Inspect the drum, belt, and front glides for wear. Clean lint from the drum and cabinet to prevent overheating. Use self-tapping screws provided to thread the unthreaded metal plate. Replaces part numbers: 5303281153, AP2142648, 1851, 3281153, 5304459240, 85-852, AH459829, DE724, EA459829, PS459829, Q000142850, Q142850, WQ142850, 08015113, 08015324, 131378400, 131777700, 137088600, 137088620, 137088630, 3281019, 3281020, 5303281009, 5303286875, 8015113, 8015324, 902088, Q000022224, Q000500537, WQ22224, WQ500537 Compatibility: Compatible with models including but not limited to: Frigidaire: FDE436RBS2, FDE546RBS1, FDE747RES0, FDES69RHW1, FEX831CS0, FEQ332ES0, FEQ1442ES0, LEQ6000ES0, LEQ2152EE0, GLEQ2152ES0, MDG336MBW2, MDG436RBD0 Kenmore: 417.49012890, 417.59012890, 417.94802301, 417.97812700 Electrolux: AEQ6000ES2, AGQ6000ES2 Gibson: GDE436RBW1, GDE546RBS1 Westinghouse: WDE846RBW0 Verify your model number or contact Parts-O-Matic support for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Frigidaire, Electrolux, Kenmore, Gibson, Westinghouse, Kelvinator, Tappan, Crosley, and Universal/Multiflex dryer models. 🔥 Specifications: Includes 1 white plastic bearing cup (131825900, ~2" diameter x 1" depth), 1 ball shaft (131777700), 1 ball bearing (5303281019), 1 ball bearing retainer (5303281020), high-temperature lubricant tube, 3 self-tapping screws, 3 washers, 2 bracket screws, bearing assembly ~1-15/16"L x 1"W x 1-3/8"H with mounting holes 1-1/2" apart (center to center). 💰 Genuine OEM Part. 🛠️ Easy Installation: Requires a putty knife, Phillips screwdriver, flat-blade screwdriver, work gloves, optional second person; typically installed in 45–90 minutes. 🛡️ Reliable Fixes: Resolves loud noises, drum not tumbling, or marks on clothes. Safety First: Unplug the dryer from the power source and, for gas dryers, shut off the gas valve before installation. Shop Parts-O-Matic for Genuine OEM appliance parts with a 30-day return policy. Get your dryer back to smooth, quiet performance today! Add to cart now for a budget-friendly fix!

Read more less

134511600 Genuine OEM Frigidaire Washer Drive Belt The 134511600 is a Genuine OEM Frigidaire replacement washer drive belt compatible with a wide range of Frigidaire, Electrolux, Gibson, Kelvinator, Kenmore, Tappan, White-Westinghouse, and Crosley top-load and laundry center washers — including the FLS, FWS, FLEB, GLWS, FEZ, FGZ, and related series. The drive belt is a wrapped V-style rubber belt that connects the motor pulley to the washer tub, transferring the motor's rotation to spin the basket during the wash and spin cycles. When the belt breaks, wears out, or stretches, the motor continues to run but the basket stops rotating — the washer fills with water and drains but does not agitate or spin, leaving clothes soaking wet. This is a Genuine OEM part manufactured by Frigidaire to factory specifications. The belt measures approximately 32-1/4" in length (30" inner circumference) x 1/2" wide x 5/16" high — a wrapped V-belt profile that seats on the motor pulley. It directly replaces 1156860, 131234000, 131686100, 134161100, 145371, 3204418, F145371, F145371-000, AP3867042, AH1146950, EA1146950, EAP1146950, LB117, PD00000111, and PS1146950. Installs in 15–30 minutes with basic hand tools. Quick Answer The 134511600 Genuine OEM Frigidaire Washer Drive Belt fixes Frigidaire-platform top-load washers that won't agitate, won't spin, pump and drain but don't spin, make a burning rubber smell, or are noisy. Wrapped V-belt, approx. 32-1/4"L (30" inner circumference) x 1/2"W x 5/16"H, black rubber. Genuine OEM. Replaces 1156860, 131234000, 131686100, 134161100, 3204418, F145371, AP3867042, AH1146950, EA1146950, LB117, PS1146950. Compatible with Frigidaire, Electrolux, Gibson, Kelvinator, Kenmore, Tappan, White-Westinghouse, and Crosley. Common Problems This Part Fixes Washer not agitating — belt has broken or slipped off the motor pulley Washer pumps and drains normally but does not spin clothes — belt failed Washer fills and drains but drum never moves — no belt drive to the basket Burning rubber smell during the wash or spin cycle — belt slipping on the motor pulley Squealing or grinding noise during operation — worn or slipping belt Washer spinning slowly or unevenly — stretched belt losing grip on the pulley Belt visibly cracked, frayed, broken, or missing inside the washer cabinet Replaces Part Numbers This washer drive belt directly replaces the following OEM and cross-reference part numbers: 134511600, 1156860, 131234000, 131686100, 134161100, 145371, 3204418, AH1146950, EA1146950, F145371, F145371-000, AP3867042, PS1146950. Contact our support team with your model number if you need confirmation before ordering. Compatibility This washer drive belt is compatible with select top-load washers and laundry centers from the following brands and series: Frigidaire washers — FLS, FWS, FLEB, FEZ, FGZ, FLSG, GLWS, GLET, FWX, GWS series and related models Electrolux washers (select Frigidaire-platform models) Gibson washers (select models) Kelvinator washers (select models) Kenmore / Sears washers — 41 series and other Frigidaire/Electrolux-built models Tappan washers (select models) White-Westinghouse washers (select models) Crosley washers (select models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Genuine OEM part manufactured by Frigidaire to factory specifications — guaranteed fit and performance Wrapped V-belt style — connects the motor pulley to the washer tub to spin the basket during agitation and spin cycles Dimensions: approximately 32-1/4"L (30" inner circumference) x 1/2"W x 5/16"H Black rubber construction — designed to withstand continuous flexing and motor load under normal wash conditions Replaces 1156860, 131234000, 131686100, 134161100, 3204418, F145371, AP3867042, LB117, PS1146950, and additional cross-references Compatible with Frigidaire, Electrolux, Gibson, Kelvinator, Kenmore, Tappan, White-Westinghouse, and Crosley washers DIY repair — installs in 15–30 minutes with basic hand tools Product Specifications Part Number 134511600 Part Type Washer Drive Belt (Wrapped V-Belt) Condition Genuine OEM Application Top-Load Washers and Laundry Centers Belt Style Wrapped V-belt Length (overall) Approximately 32-1/4 inches Inner Circumference Approximately 30 inches Width 1/2 inch Height 5/16 inch Material Rubber Color Black Quantity Sold individually (1 belt) Compatible Brands Frigidaire, Electrolux, Gibson, Kelvinator, Kenmore, Tappan, White-Westinghouse, Crosley Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off the water supply before beginning. On most compatible Frigidaire-platform washers, the drive belt is accessed by removing the back panel or by laying the washer on its side to access the motor and pulley from the bottom. The belt wraps around the motor pulley (small, at the motor shaft) and the transmission pulley or basket (large, beneath the tub). Release the old belt by slipping it off the motor pulley — the motor may need to be slightly unbolted and shifted to relieve tension, depending on your model. Route the new 134511600 belt around both pulleys in the same path as the original and seat it firmly in the V-groove on each pulley. If the motor position is adjustable, re-tension the belt so it deflects no more than 1/2 inch when pressed in the middle. Reinstall the back panel, restore power and water, and run a test cycle to confirm the basket agitates and spins normally. Tools needed: Phillips screwdriver, socket set or adjustable wrench. Frequently Asked Questions What does the washer drive belt do? The drive belt is the power transmission link between the motor and the washer basket. The motor turns a small drive pulley on its shaft, and the drive belt wraps around both the motor pulley and the larger transmission or basket pulley, transferring the motor's rotation to spin the basket. Without an intact, properly tensioned belt, the motor runs but the basket stays still — the washer fills with water, pumps it out, but never agitates or spins clothes. A broken, cracked, or slipping drive belt is one of the most common causes of washer failure on Frigidaire-platform top-load models. What is the difference between 134511600 and 1156860? These are the same drive belt. 1156860 is an older cross-reference part number and item number for the same belt that Frigidaire consolidated into the current part number 134511600. The 134161100, 131234000, 131686100, and 3204418 numbers are also cross-references for this same belt from various parts catalog revisions. All are covered by this OEM belt. My washer pumps but won't spin — is it the belt? A washer that pumps and drains normally but does not spin the basket is a classic drive belt failure symptom on Frigidaire-platform top-load washers. Since the drain pump is typically driven separately from the basket, a broken belt will stop basket rotation while leaving the pump functioning normally. Open the back panel and visually inspect the belt — if it is broken, stretched to the point of slipping, or missing entirely, replacing the 134511600 belt will restore normal spin and agitation. If the belt looks intact but the basket still doesn't turn, check the motor capacitor or idler pulley. Should I also inspect the idler pulley when replacing this belt? Yes — since the washer must be partially disassembled to replace the belt, this is a good opportunity to inspect the idler pulley for wear. The idler pulley maintains belt tension on compatible models — if the pulley bearing is worn or the spring tension is reduced, the belt will slip even when new, causing a burning rubber smell and poor spin performance. The Frigidaire washer idler pulley is sold separately (part 131462600 or 134371700 depending on model). If the idler pulley wobbles or the wheel doesn't spin freely by hand, replace it at the same time as the belt. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Frigidaire to factory specifications. It is the exact same drive belt installed in compatible Frigidaire, Electrolux, Gibson, and related brand top-load washers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

(5 Pack) EXP25A Ceramic Line Fuse, Fast Blow,  25A, 250V  It can be used in many applications.    California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

(2 Pack) EXPHV11 Microwave High Voltage Diode (Rectifier) Replaces: GE, LG, AMANA, ELECTROLUX, GE, KENMORE, MAYTAG, WHIRLPOOL, Frigidaire T3512, 3512, T4512, H, CL01-12, HVM12, 512 H, 12Kv, 350mA.   Replaces Part Numbers: 11QBP0236, AP5633254, PS4085133, AP3192533, PS239740 EA239740, WB27X10597, 13091701, AP6005641 PS11738693, WP13091701, 417726, 00188507 AP3382376 PS8712310, 00417726, PS11745270, AP6012063, 8205489, AP4357534, PS2339491, EA2339491, 5304467670, AP4564925, 3518400400, PS11745270, AP6012063, WP8205489, PS3654932, AP5631218, W10245187, W10492278. Description: This Diode Assembly is a replacement part for specific microwave models. It plays a crucial role in converting alternating current (AC) to direct current (DC), which is essential for the microwave’s high-voltage functions, including powering the magnetron to generate microwave energy. Over time, diodes can fail due to electrical surges, excessive heat, or wear and tear. A faulty diode assembly can lead to inefficient or non-functional microwave operation, impacting its ability to heat food properly. Microwave High Voltage Diode – Universal Replacement Restore your microwave’s heating function with this high-quality high voltage diode. Built to handle up to 12,000V / 500mA, it’s a reliable replacement for worn or damaged diodes in many major brands. Features: Direct replacement for most microwave models Durable and rated for high-voltage performance Fixes common issues like no heat or humming Fits brands: GE, Whirlpool, LG, Samsung, Panasonic, Frigidaire, and more. ⚠️ Installation should be done with power disconnected. Not sure if it fits? Contact us to confirm compatibility.

Read more less

6 Pack - XPARTCO 6602-001655 Dryer Drum Belt – Compatible with Samsung & Kenmore Dryers Product Description Restore proper drum rotation and reliable drying performance with the XPARTCO 6602-001655 Dryer Drum Belt. This Belt is a replacement part is compatible with specific Samsung dryer models. The belt attaches to the motor pulley and spins the drum as the motor rotates. Over time, the belt can snap. This is due to general wear and tear, overloading, or excessive friction do to a damaged felt seal. Whenever the dryer belt breaks, the drum will not rotate and would need to be replaced. Replaces Part Numbers 6602-001655, 6602-001314, 5PH2337, PD00002012, EAP2407938, AP4373659, PS4133825. Compatibility This replacement dryer drum belt fits select Samsung and Kenmore (Samsung-manufactured) dryers. Example compatible models include (but are not limited to):Samsung DV45H7000EW, DV42H5200EPKenmore 592-89045, 592-89047 Always verify your dryer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM belt length, width, and tension 🌀 Restores Drum Rotation – Ensures smooth, consistent tumbling 💪 Reinforced Rubber Construction – Designed to resist stretching and wear 💰 Cost-Effective Repair – Reliable performance without OEM pricing 🛡️ Fixes Common Issues – Solves drum not turning, squealing noises, or slipping belt 📐 Product Specification Part Number: 6602-001655 Component Type: Dryer Drum Belt Material: Reinforced rubber Belt Style: Ribbed, 5 Rib, 92" Application: Motor-to-drum drive system Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver ⚠️ Safety First: Always unplug the dryer before servicing to prevent electrical shock. Steps: Disconnect dryer power and open the cabinet. Remove the drum to access the belt path. Remove the worn belt from the motor and idler pulleys. Install the new XPARTCO 6602-001655 belt following the original routing. Reinstall the drum, reassemble panels, and restore power. Run a test cycle to confirm proper operation. ⏱️ Time Required: 30–45 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Restore smooth dryer operation — Add to Cart Now for a dependable, budget-friendly repair!

Read more less

Deflecto UBGWB Universal Bird Guard Dryer Vent Cover 3"-4" (White) - Fits Most 3" or 4" Dryer and Bathroom Vents Product Description Protect your dryer or bathroom exhaust vent with the Deflecto UBGWB Universal Bird Guard Dryer Vent Cover in White. Designed to fit over any 3" or 4" vent hood, this durable, weather-resistant cover prevents birds, rodents, and debris from entering or nesting, ensuring efficient airflow and reducing fire hazards. Made of UV-resistant plastic, it self-cleans with wind or rain, offering long-lasting protection for both residential and commercial applications. Note: Includes one bird guard cover. Disconnect power and gas (if applicable) before installation. Check guard periodically for lint or debris buildup. Replaces part numbers: UBGWB, UBGBB, PBH50WZW, AP4246336, 1370849 Compatibility: Compatible with most 3" or 4" dryer and bathroom exhaust vent hoods, including but not limited to: Whirlpool, Maytag, Kenmore, GE, Samsung, LG, Frigidaire, Bosch dryers Standard bathroom exhaust vents (3" or 4" diameter) Universal fit for most major brand vent hoods Verify your vent hood size or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits most 3" or 4" dryer and bathroom exhaust vent hoods from major brands. 🛡️ Specifications: UV-resistant plastic bird guard, fits 3" or 4" vent hoods, self-cleaning design. 💪 Reliable Performance: Durable and weather-resistant, prevents pests and debris entry. 🛠️ Easy Installation: Requires screwdriver; typically installed in 5–10 minutes. 🔥 Effective Protection: Reduces lint buildup and fire hazards while maintaining airflow. Product Specification Part Number: Deflecto UBGWB Component Type: Universal bird guard dryer vent cover Material: UV-resistant plastic Dimensions: 7.25" H x 7.25" W x 4.5" D Weight: 9.6 oz (Based on web:0) Mounting: Fits over 3" or 4" vent hoods, secured with screws Operating Conditions: Suitable for outdoor dryer and bathroom exhaust vent environments Compliance: Prop 65 warning for California Installation Notes: Safety First: Disconnect the dryer from the power source and gas supply (if applicable) before installation. Shop for high-quality appliance accessories with a 30-day return policy. Keep your dryer vent safe and efficient today! Add to cart now for reliable protection!

Read more less

ERP UVLIGHT LED UV Flashlight Batteries not included  California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less