Washer Parts

W11688995 Genuine OEM Whirlpool Washer Water Inlet Valve (Cold) The W11688995 is a genuine Whirlpool OEM cold water inlet valve for Whirlpool-built front-load washers. Whirlpool's newer front-load platforms use two separate single-function valves instead of one combined hot/cold valve body — this cold-side valve handles only the cold water supply, while a matching hot-side valve (sold separately as W11688994) handles the hot side. When the control calls for a cold fill, it energizes this valve's solenoid coils to open the water path; when the correct level is reached, the valve closes again. If this valve fails to open, the washer won't take on cold water; if it fails to seal fully closed, water can trickle into the drum even when the washer isn't running. Because this is a dedicated single-function valve, a failure here shows up in a very specific way: cold-only fills stop working or slow down dramatically, while hot-only fills (governed by the separate W11688994 valve) continue working normally. Whirlpool's own service guidance links this valve to F8 E1 and LO FL fill-related error codes. Common failure modes include mineral or sediment buildup that prevents the valve from sealing, a burned-out solenoid coil, or a worn internal diaphragm. It directly replaces W11036930, W11316256, W11486361, AP7218603, PS17216730, and EAP17216730. As a genuine OEM part, the W11688995 is manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. Quick Answer The W11688995 Genuine OEM Whirlpool Washer Water Inlet Valve (Cold) fixes Whirlpool-built front-load washers where cold water won't fill, fills slowly, overfills, leaks into the drum when off, or throws an F8 E1 or LO FL error code. 120V, 50/60Hz, two-coil cold-only valve, 1/2" NPT threaded connections. Replaces W11036930, W11316256, W11486361, AP7218603, PS17216730, EAP17216730. This is the cold-side valve only — the companion hot-side valve is sold separately as W11688994. Common Problems This Part Fixes Washer won't fill with cold water while hot water fills normally Cold water fills much more slowly than it used to Washer overfills or takes on more water than the cycle calls for Water trickling or leaking into the drum on the cold side when the washer is off F8 E1 or LO FL error code displayed on the control panel Cycle stalling at the fill step and never advancing to wash Cold-wash or cold-rinse cycles specifically affected while warm/hot cycles run fine Water pooling underneath or behind the washer near the cold supply connection Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer cold water inlet valve directly replaces the following OEM and cross-reference part numbers: W11688995, W11316256, W11036930, W11486361, 4983050, PD00086086, FIX17216730, EAP17216730, OEM28874414, AP7218603, AWP46809, PS17216730. W11486361 and W11316256 were earlier Whirlpool numbers for this same valve, with W11036930 preceding those. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This cold water inlet valve is compatible with select Whirlpool-built front-load washers across the Whirlpool family of brands, including: Whirlpool front-load washers — WFW series Maytag front-load washers — MHW and MFW series (select Whirlpool-built models) Amana front-load washers (select models) Inglis front-load washers — IFW series (select models) Select Kenmore front-load washers built on the Whirlpool platform Verified model numbers include: 8TWFC6810LW0 (laundry center), IFW5900HW0, IFW5900HW1, IFW5900HW2, IFW5900HW3, IFW5900HW4, MFW7020RF0, MFW7020RU0, MFW7020RW0, MHW5630HC0, MHW5630HC1, MHW5630HC2, MHW5630HC3, MHW5630HW0, MHW5630HW1, MHW5630HW2, MHW5630MBK0, MHW6630HC0 through MHW6630HC3, MHW6630HW0 through MHW6630HW3, MHW6630MBK0, MHW8630HC0 through MHW8630HC3, MHW8630HW0 through MHW8630HW3, WFW560CHW0, WFW560CHW1, WFW560CHW2, WFW5620HW0 through WFW5620HW3, WFW6620HC0 through WFW6620HC2, WFW6620HW0, WFW6620HW1, WFW8620HC0 through WFW8620HC4, WFW8620HW0 through WFW8620HW4, WFW862CHC0, and WFW862CHC1. Note — cold side only: This is the cold water valve. The matching hot water valve for these same washers is sold separately under part number W11688994. The two are not interchangeable — each is a dedicated single-function valve, and installing this cold valve in place of the hot valve (or vice versa) will not correctly control water temperature. If both valves need replacement, order both part numbers. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine Whirlpool OEM part — factory-specified solenoid, seal, and flow-rate design Dedicated cold-only water inlet valve — two internal coils control flow to the cold supply Resolves "won't fill with cold water," "fills slowly," "overfills," and "leaking into the drum" symptoms caused by valve failure Commonly resolves F8 E1 and LO FL error codes 1/2" NPT threaded connections for standard supply line hookups Direct drop-in replacement for W11036930, W11316256, and W11486361 Replaces W11036930, W11316256, W11486361, AP7218603, PS17216730, and EAP17216730 Compatible with Whirlpool, Maytag, Amana, Inglis, and select Kenmore front-load washers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number W11688995 Part Type Washer Water Inlet Valve — Cold Condition Genuine OEM Brand Whirlpool Application Front-Load Washers (Whirlpool-Built) Voltage 120V Frequency 50/60 Hz Coils 2 (dedicated cold water function) Connection 1/2 in. NPT threaded Companion Part W11688994 (hot water valve, sold separately) Supersedes W11036930, W11316256, W11486361 Quantity 1 valve Compatible Brands Whirlpool, Maytag, Amana, Inglis, select Kenmore Installation Notes ⚠️ Shut Off Water Supply And Unplug Washer Before Starting — Have A Towel Ready Unplug the washer or shut off its circuit breaker, and shut off both the hot and cold water supply valves before beginning. Wear work gloves. Disconnect the cold water supply line from the back of the valve first — have a towel or shallow pan ready, since residual water will spill out. Remove the rear screws securing the top panel, then slide the panel back and lift it off to access the valve assembly from inside the cabinet. Photograph the wiring connections before disconnecting anything, since the hot and cold valves sit side by side and it's easy to cross a wire. Disconnect the electrical connector from the old cold valve, remove its mounting screw or bracket, and pull the valve free — leave the hot valve (W11688994) undisturbed if it isn't also being replaced. Install the new W11688995 in the same position, secure the mounting screw, and reconnect the electrical connector fully. Reattach the cold water supply line, tightening securely by hand plus a partial turn with pliers — avoid overtightening plastic threaded fittings. Reinstall the top panel, restore the water supply, and check the connection for leaks before restoring power. Run a short cycle set to a cold wash and confirm the tub fills at the normal rate with no leaking underneath or behind the washer. Tools needed: 1/4" nut driver or socket, T-20 Torx bit, pliers, towel or shallow pan, work gloves. Frequently Asked Questions Cold water won't fill but hot water works fine. Is this the right part? Yes — that's exactly the symptom pattern this valve addresses. Because your washer uses two separate single-function valves rather than one combined valve, a fault on the cold side only affects cold fills while the hot valve (W11688994) keeps working independently. If cold-specific cycles are the ones failing, this cold valve is the correct part to replace. Do I need to replace both the hot and cold valves at the same time? Not necessarily. Since these are independent single-function valves, you only need to replace the one that has actually failed. If only cold fills are affected, replacing this W11688995 valve alone is sufficient. If both hot and cold fills are having problems, or if the valves are original and quite old, some people choose to replace both at once since they're already accessing the same area — but it's not required. My washer shows an F8 E1 or LO FL error. Does that mean this valve is bad? It's a strong indicator, but check the basics first. These codes generally mean the control didn't see water reach the expected level within its allotted fill time. Before replacing the valve, confirm the cold supply valve at the wall is fully open, check the inlet screen inside the valve port for sediment or debris, and make sure the cold fill hose isn't kinked. If those check out and cold water still won't fill properly, this valve is the likely cause. Can I use this valve on the hot water side instead? No. This is a dedicated cold-water valve, and the hot-water side uses a separate part number, W11688994. The two are built and calibrated for their specific supply line and are not interchangeable — installing the cold valve on the hot side (or vice versa) will not properly control water temperature during the cycle. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It includes the same two-coil solenoid design, seal, and flow-rate calibration as the cold water inlet valve originally installed in your front-load washer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WH13X10024 Genuine OEM Washer Water Valve Replaces Part Numbers: WH13X10024, WH13X0086, WH13X0087, WH13X10004, WH13X10019, WH13X86, WH13X87, AH1155105, EA1155105, OEM15444478, AP3861119, PS1155105. Description: This Water Inlet Valve is a Genuine OEM part for select GE washing machine models. This component is crucial for controlling the flow of water into the washer during the wash and rinse cycles. It works by opening and closing the solenoids to allow the appropriate amount of hot or cold water to enter the washing machine, based on the selected settings.   California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

DC64-01570A Washer Genuine Door Boot Rubber boot assembly. Fits select Samsung front-load washer models. Replaces Part Numbers: DC64-01570A, DC97-14560A, DC97-14560K, DC97-14560L,  AP4342244, PS4211426. Description: This Washer Door Diaphragm is an essential component for maintaining your washer's functionality. This Genuine replacement part ensures a secure and effective seal, preventing leaks and enhancing the overall performance of your washing machine. Specifically designed for compatibility with a range of Samsung washer models, it guarantees a perfect fit and straightforward installation. Made from durable materials,  

Read more less

8182415 Washer Genuine OEM Drain Pump Fits Specific Whirlpool, Maytag washer Models. Replaces Part Numbers: WP8182415, 8182415, OEM24047170, AP6011792, 1065543, PS11744991. Description: This Drain Pump is a Genuine OEM part for specific Whirlpool, Maytag, Kenmore washing machine models.    California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

WH13X26535 Genuine OEM GE Washer Water Valve The WH13X26535 is a genuine GE OEM water inlet valve assembly for GE top-load washers, and also fits select Hotpoint, Haier, Monogram, and Café models. This valve controls the flow of hot and cold water into the tub during the fill portion of the cycle, ensuring each wash uses the correct amount of water at the right temperature blend. It's housed in durable gray plastic. Common failure causes include mineral or sediment buildup inside the valve body, a burned-out internal solenoid coil, and general wear over years of use — five years is a commonly cited service life before this valve starts to show problems. A failing valve produces a clear set of symptoms: the washer not filling properly, water continuing to fill or drip even when the washer is turned off, or leaking near the valve area. It directly replaces AP6892695, WH13X24386, 4931303, PS12726769, WH13X24392, WH13X26535-25PK, EAP12726769, and PD00052736. As a genuine OEM part, the WH13X26535 is manufactured by GE to factory specifications — guaranteed fit, materials, and performance. Quick Answer The WH13X26535 Genuine OEM GE Washer Water Valve fixes GE top-load washers that aren't filling properly, are overfilling, or have water slowly dripping into the tub even when the washer is off. Housed in gray plastic. Replaces AP6892695, WH13X24386, 4931303, PS12726769, WH13X24392, WH13X26535-25PK, EAP12726769, PD00052736. This replacement valve does not include a thermistor or gasket — if your old valve has a thermistor mounted in front of the solenoids, you'll need to transfer it (with its gasket) to the new valve. Also not the same as the similarly-numbered WH13X26534, which is a separate valve for other GE/Hotpoint models. Common Problems This Part Fixes Washer not filling with water properly Washer overfilling Water slowly dripping or leaking into the tub even when the washer is turned off Leaking near the valve connections No hot water reaching the tub, or no cold water reaching the tub Cycle stalling at the fill step and never advancing to wash Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer water inlet valve directly replaces the following OEM and cross-reference part numbers: WH13X26535, WH13X24386, WH13X24392, 4931303, 003C17, AGE26261, AP6892695, 4476388, 4931303, OEM20678094, EAP11729481, EAP12726769, K-78637-2, PD00052736, PS12726769. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water valve is compatible with select GE top-load washers, and also fits select Hotpoint, Haier, Monogram, and Café washers built on the GE platform, spanning model series GTW460, GTW465, GTW485, GTW490, GTW500, GTW525, GTW540, and VTW540, including specific model numbers such as 5TW4207ST0WS, 5TW4307SW0WS, ETW485ASW0WB, GTW460AMJ0WW, GTW460AMJ1WW, and GTW460AMJ2WW. Note — thermistor transfer required, and not the same as WH13X26534: This valve does not include a thermistor or the rubber gasket that seats it. If your original valve has a thermistor mounted in front of the solenoids, you must transfer that thermistor and its gasket onto this new valve during installation. Separately, this part is not the same as the similarly-numbered WH13X26534, a distinct valve used on other GE/Hotpoint models with its own cross-reference set (PS12726768, AP6891106). Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine GE OEM part — factory-specified solenoid design and housing Controls hot and cold water flow into the tub Resolves "won't fill properly," "overfilling," and "dripping into the tub when off" symptoms caused by valve failure Durable gray plastic housing Direct drop-in replacement — matches the original mounting and hose connections Replaces AP6892695, WH13X24386, 4931303, PS12726769, WH13X24392, WH13X26535-25PK, EAP12726769, and PD00052736 Compatible with GE, Hotpoint, Haier, Monogram, and Café top-load washers Genuine OEM replacement — guaranteed fit, materials, and performance Moderate DIY repair, typically 30 to 60 minutes Product Specifications Part Number WH13X26535 Part Type Washer Water Inlet Valve Condition Genuine OEM Application Top-Load Washers Housing Material Gray plastic Includes Thermistor/Gasket No — transfer from old valve if equipped Repair Difficulty Moderate — 30 to 60 minutes Quantity 1 valve Compatible Brands GE, Hotpoint, Haier, Monogram, Café Installation Notes ⚠️ Shut Off Water Supply And Unplug Washer Before Starting — Watch For The Thermistor O-Ring Disconnect power at the outlet or shut off the circuit breaker, and shut off both hot and cold water supply valves before beginning. Wear work gloves. Access is typically behind the front control panel or top of the cabinet, depending on your model. The valve assembly is usually held in place with a metal plate and two screws. Photograph the wiring and hose connections before disconnecting anything. If your old valve has a thermistor (temperature sensor) mounted in front of the solenoids, it fits into a small hole in the bracket and uses an O-ring seal that's known to degrade and leak over time — this new valve does not include one, so you'll need to carefully transfer the thermistor and its gasket from the old valve to the new one. Disconnect the electrical connector and outlet hoses from the old valve, remove its mounting screws, and pull it free. Transfer the thermistor and gasket to the new WH13X26535 if applicable, then install it in the same position, reconnect all outlet hoses to their original positions, reconnect the electrical connector, and secure the mounting screws. Reattach the hot and cold supply hoses, tightening securely. Restore the water supply and check every connection for leaks before restoring power. Run a full test cycle across a few different temperature settings to confirm each fill function works correctly with no leaking. Tools needed: Phillips screwdriver, pliers, work gloves. Frequently Asked Questions Does this valve come with the thermistor? No. This valve no longer comes with the rubber gasket or thermistor that some GE washers use, mounted directly in front of the solenoids. If your old unit has one, you'll need to remove it from the old valve, along with its gasket, and transfer it onto this new valve during installation. Water has been slowly leaking into my tub even when the washer is off. Is that this valve? Yes, this is a documented cause. One customer traced over a year of slow leaking directly to this valve's thermistor O-ring, which is known to degrade over time and let water seep through even when the washer isn't running. Replacing the valve (and transferring a good thermistor and gasket if your model uses one) resolves this type of slow leak. Is this the same as WH13X26534? No, these are two separate GE valve part numbers with different cross-reference sets, despite the similar numbering. Always confirm the exact part number from your washer's parts diagram or the sticker on your old valve rather than assuming based on a close number match. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by GE to factory specifications — guaranteed fit, materials, and performance. It matches the original solenoid design, housing, and connection type of the water inlet valve originally installed in your washer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

Genuine OEM WPW10140917 Washer Water Inlet Valve with Vacuum Break The Genuine OEM Whirlpool WPW10140917 is the water inlet valve with vacuum break for select Whirlpool-built washers, including Maytag, Kenmore, Amana, Inglis and other brands. The valve regulates water intake for wash cycles and delivers water into the washer drum, and the vacuum break helps keep wash water from backing up into the supply. When the valve fails, the washer may leak, and fill problems can follow. This is the original Whirlpool part, not an aftermarket equivalent. Check your model number before ordering. Quick Answer The Genuine OEM WPW10140917 Water Inlet Valve replaces the water inlet valve on a compatible Whirlpool-built washer when it leaks or no longer controls water intake correctly. Replaces W10140917. Classic symptom: water leaking at the valve. Common Problems This Part Fixes Water leaking at the inlet valve Water inlet valve not controlling water intake correctly Washer not filling or filling incorrectly because of a failed valve Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This water inlet valve replaces or supersedes the following part numbers: WPW10140917, W10140917, OEM18047055, AP6015682, AWP49689, EAP11748963, PD00003949, PS11748963 Whirlpool sells similar valves under nearby numbers, such as WPW10140918, which are not interchangeable by number alone. If your old valve shows a different number, contact our support team and we'll check whether it matches. Compatibility This water inlet valve is listed for Whirlpool, Maytag, Kenmore, KitchenAid, Amana, Inglis, Jenn-Air, Magic Chef and Crosley washers, including these examples: WTW5100VQ1, WTW5100VQ2, WTW5300SQ2, 1CWTW5100VQ1 CAWS9234VQ0, ETW4400VQ3, NTW4500VQ1 ITW4300SQ3, IV45001, IV4500X0 Note: The models above are a small sample, not a full list. Check your full model number against your parts diagram, or contact our support team to verify fit before ordering. Key Features Genuine OEM Whirlpool part, not an aftermarket equivalent Water inlet valve with vacuum break Regulates water intake and delivers water into the washer drum Sold as one complete valve Product Specifications Part Number WPW10140917 OEM Part Number WPW10140917 Part Type Washer Water Inlet Valve with Vacuum Break Condition Genuine OEM Manufacturer Whirlpool Application Select Whirlpool-Built Washers Installation Notes ⚠️ Unplug Power And Shut Off Water Before Installing Unplug the washer and turn off the water supply before you begin, and wear protective gloves. Access to the valve is typically through the back panel or the control panel, depending on the model. Note where each hose and wiring connector goes, disconnect them, remove the old valve, and fit the new valve in the same position. Reconnect everything, restore water and power, and run a short cycle while checking for leaks. Frequently Asked Questions My washer is leaking at the valve. Is this the part I need? If the leak is coming from the water inlet valve itself, replacing the valve is the repair. Check the supply hoses and their connections first, since a loose or worn hose can leak in the same area. Is this an OEM or aftermarket part? This is a genuine OEM part from Whirlpool, not an aftermarket equivalent. Can I use a valve with a similar part number? Not by number alone. Whirlpool sells several water inlet valves with similar numbers for different washers. Match the part number and your model number, or contact our support team and we'll check for you. Will this fit my washer? It is listed for many Whirlpool-built washers, but the model list above is only a sample. Check your full model number against your parts diagram, or contact our support team and we'll verify it before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

WP8182119 Washer Genuine OEM Door Boot Gasket Genuine OEM washer door boot gasket designed to create a watertight seal between the washer tub and front door assembly. ✓ Genuine OEM Part ✓ Replaces WP8182119 ✓ Compatibility Support Product Description The Genuine OEM WP8182119 Washer Door Boot Gasket helps create a secure watertight seal between the washer tub and front door assembly. A torn or worn gasket can cause leaks, mold buildup, or poor door sealing performance. Replacing the washer door boot gasket can help restore proper sealing and reduce water leaks during operation. Quick Answer If your washer is leaking from the front door area or the gasket is torn, damaged, or moldy, the WP8182119 washer door boot gasket may need replacement. ⚠️ Always verify your washer’s model number before ordering. Contact our support team if you’re unsure. Common Problems This Part Fixes Front-load washer water leaks Torn or damaged door gasket Mold or mildew buildup Poor washer door sealing Water leaking around washer door Replaces part Number WP8182119, 8182119, W10003800, AWP825300, AP6011758, EAP11744957, PD00002449, PS11744957. Compatibility This part fits select Whirlpool, Kenmore, Maytag, and compatible front-load washer models using part number WP8182119. Always verify your washer’s model number before ordering. Contact our support team if you’re unsure. Key Features Genuine OEM washer door boot gasket Helps prevent washer door leaks Supports proper watertight sealing Designed for compatible washer models Durable OEM replacement component Product Specifications Brand Whirlpool Part Type Washer Door Boot Gasket Primary Part Number WP8182119 Compatible Appliance Type Washer Condition Genuine OEM New Installation Disconnect power before installation. Ensure gasket is aligned properly to prevent leaks. Troubleshooting Guide ⚠️ Disconnect power before servicing the washer. Inspect the gasket for tears or mold buildup. Check door alignment and sealing condition. Test washer operation after installation. Replace the gasket if leaks continue around the door area. When Should You Replace This Part? Replace the washer door boot gasket if the washer leaks from the front door area or the gasket becomes torn, damaged, or heavily worn. Shop With Confidence We are a U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock parts for major appliance brands and ship quickly from our U.S. warehouse. ✓ Fast Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

285751 Washer Genuine Agitator Dog Cam Kit Replaces Part Numbers:  285751, 2837, 3351019, 387092, 3947410, AH334624, EA334624, OEM9283568, AP3094521, PS334624. Description: This Agitator Kit is an OEM replacement part for specific Whirlpool top-loading washer models. Installed in the center of the wash basket, it aids in the mechanical agitation central to regular laundry cleaning.It contains the plastic cam and four plastic dogs needed to repair a malfunctioning or noisy agitator during the wash cycle.   California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

WPW10409079 Washer Genuine OEM Drain Pump Replaces Part Number: WPW10409079, W10409079, 2118648, AP6021043, PS11754363, LP09079. Description: This Drain Pump is a replacement part for specific Whirlpool top-loading washing machine models. Located near the bottom center of the machine, it actively pumps water out of the washer tub at the end of each cycle.  The pump motor spins an impeller chamber to push water through the drain hose and out of the home. Causes of failure include clogging from mineral buildup or fabric fibers within the pumping components. Over time, motor windings experience excess heat and may burn out from consistent drainage cycles. WPW10409079 is the part number for a Whirlpool washer drain pump that removes water from the washer during the drain cycle. It is compatible with many Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef models.

Read more less

WDH6FT Washer Universal 6' Corrugated Drain Hose 6 foot. Corrugated plastic hose fits 1", 1-1/8", 1-1/4" & 1-3/8" outlets for Whirlpool, Kenmore, GE, Frigidaire & most other brands. Cross Reference: WDH6FT, TJ76WDH, AP4568426, 200-6, 2046, 48397, 600-6P, 60356, 6WDH, ERSSD6, HP395, HP406, HP406E, R87-407, SSD-6, SSD6, TJ6WDH, TJSSD-6, OEM13705283, WDH6FT. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov  

Read more less