Search results for "washer switch"

WP389140 Genuine OEM Whirlpool Washer Drive Block The WP389140 is a genuine Whirlpool OEM drive block for large-capacity belt-drive and direct-drive top-load washers. This is a purely mechanical coupling component: it connects the inner spin basket to the transmission's drive shaft, so that when the transmission turns, the basket turns with it. Without a properly seated drive block, the connection between the motor's rotational power and the basket is lost or unreliable, even though every electrical component in the washer may be working perfectly. Measuring approximately 2-5/16" high, this drive block is a wear component subject to gradual mechanical stress every time the washer agitates or spins. A worn or failed drive block produces a distinctive set of symptoms: the basket may spin freely without properly engaging, the washer may spin slowly and leave clothes excessively wet, or you may hear a loud knocking or banging noise during operation as the connection between the basket and drive shaft becomes loose or worn. It directly replaces 389140, AP6008836, 357782, 97360, J27-936, PS11741977, PS349903, AP2905773, WH40X180, WP389140VP, LP16171, and 2858. Quick Answer The WP389140 Genuine OEM Whirlpool Washer Drive Block fixes Whirlpool, Kenmore, Maytag, KitchenAid, Roper, Admiral, Amana, Crosley, Estate, and Inglis top-load washers with a basket that spins freely without engaging, slow spinning that leaves clothes excessively wet, or loud knocking/banging noise during operation. Approximately 2-5/16" high. For large-capacity belt-drive and direct-drive washers. Replaces 389140, AP6008836, 357782, 97360, J27-936, PS11741977, PS349903, AP2905773, WH40X180, WP389140VP, LP16171, 2858. This repair typically requires a spanner wrench to remove a large securing nut — budget for the right tool before starting. Common Problems This Part Fixes Washer basket spins freely without properly engaging during the wash or spin cycle Washer spins slowly, leaving clothes excessively wet at the end of a cycle Loud knocking or banging noise during operation Washer shakes or moves noticeably during spin Basket continues spinning after the cycle should have stopped Inefficient wash and spin cycles overall due to poor basket engagement Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer drive block directly replaces the following OEM and cross-reference part numbers: WP389140, 389140, 357782, 97360, PD00002363, EAP11741977, WP389140VP, AP6008836, AWP47839, J27-936, PS11741977. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drive block is compatible with select Whirlpool large-capacity top-load washers (belt-drive and direct-drive), and also fits select Kenmore, Maytag, KitchenAid, Roper, Admiral, Amana, Crosley, Estate, and Inglis washers built on the Whirlpool platform, including model numbers such as: NTW4516FW, NTW4516FW3, NTW4516FW4 WTW4816FW2, WTW4816FW3 RTW4516FW, NTW4605EW, WTW4800BQ Note: Always verify your full model number before ordering, since Whirlpool uses different drive block designs across its washer lineup. Contact our support team with your model number if you're unsure. Key Features Genuine Whirlpool OEM part — factory-specified fit for a secure basket-to-transmission connection Connects the inner spin basket to the transmission's drive shaft Resolves "basket spins freely," "slow spin, clothes too wet," and "loud knocking noise" symptoms caused by drive block wear Approximately 2-5/16" high Designed for large-capacity belt-drive and direct-drive washer platforms Direct drop-in replacement matching the original fit onto the spin tube notches Replaces 389140, AP6008836, 357782, 97360, J27-936, PS11741977, PS349903, AP2905773, WH40X180, WP389140VP, LP16171, and 2858 Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Roper, Admiral, Amana, Crosley, Estate, and Inglis washers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number WP389140 Part Type Washer Drive Block Condition Genuine OEM Brand Whirlpool Application Large-Capacity Belt-Drive and Direct-Drive Top-Load Washers Height Approx. 2-5/16 in. Function Connects the inner spin basket to the transmission drive shaft Related Component Drive cam (commonly inspected/replaced during the same repair) Repair Difficulty Moderate — spanner wrench and washer disassembly required Quantity 1 drive block Compatible Brands Whirlpool, Kenmore, Maytag, KitchenAid, Roper, Admiral, Amana, Crosley, Estate, Inglis Installation Notes ⚠️ Unplug Washer And Shut Off Water Supply Before Starting — Spanner Wrench Required Disconnect power at the outlet or shut off the circuit breaker, and shut off the hot and cold water supply valves before beginning. Wear work gloves. Remove the washer's top and control console per your model's service instructions to access the inner tub assembly. Remove the agitator and any hardware securing the basket, which typically includes a large center nut — a spanner wrench is required to remove this nut, along with a socket and long extension for other fasteners; expect to remove a fair number of components to fully access the drive block. Lift the wash basket out to expose the drive block, which sits on the spin tube near the center of the transmission. Photograph the orientation of the old drive block and any surrounding hardware before removing it. Lift the old drive block free, and while it's accessible, inspect the drive cam nearby for wear as well, since it's commonly replaced at the same time. Slide the new WP389140 drive block into position, making sure it seats fully onto the spin tube notches, and reassemble the basket, hardware, agitator, console, and top panel in reverse order. Restore water and power, then run a test cycle through both wash and spin to confirm the basket engages properly with no unusual noise. Tools needed: multi-screwdriver, spanner wrench, socket set with long extension, work gloves. Frequently Asked Questions My washer basket spins freely and doesn't seem connected to anything. Is this the drive block? Yes, this is the classic symptom of a failed drive block. Since this component is the mechanical link between the transmission's drive shaft and the inner spin basket, once it wears out or fails, the basket can spin independently without properly engaging, even though the motor and transmission are working normally. Do I really need a spanner wrench for this repair? Yes, on most models. Accessing the drive block requires removing a large nut that secures the basket assembly, and this nut is specifically designed to be removed with a spanner wrench rather than a standard socket. Trying to remove it without the correct tool risks damaging the nut or the surrounding components, so it's worth having one on hand before you start. Should I replace the drive cam at the same time? It's worth inspecting while you have the assembly open, since the drive cam sits in the same area and is commonly replaced alongside the drive block when a technician is already this far into the repair. If it shows visible wear, replacing both at once saves you from repeating this same teardown again soon after. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original dimensions and fit of the drive block originally installed in your washer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WH07X10019 Washer Drive Pulley  Genuine GE part Replaces Part Number: WH07X10019, 1264466, AH1482349, EA1482349, AP3995204, PS1482349, WH07X10018.

Read more less

XPARTCO 5220FR2008C Washer Water Valve The XPARTCO 5220FR2008C is an aftermarket replacement water inlet and dispenser valve assembly for LG front-load washers, and also fits select Kenmore models. This valve connects to your home's water source and to the washer's solenoid wiring, controlling exactly how much water enters the tub and ensuring the correct fill level for each cycle. The assembly has 1 inlet and 4 outlets. Rated 120V, 60Hz. Common failure causes include mineral or sediment buildup inside the valve body and general electrical wear in the solenoid coils. A failing valve produces a clear set of symptoms: the washer continuing to fill even after it should be full, filling slowly, overfilling, or leaking water into the drum when the washer is off. On some LG models, this can also trigger an FE error code specifically tied to the fill process. It directly replaces 5220FR2008C, 1345045, AH3527429, EA3527429, OEM13323375, AP4441122, ALG312490, PD00001833, PS3527429 Quick Answer The XPARTCO 5220FR2008C Washer Water Valve fixes LG and select Kenmore front-load washers that keep filling past full, fill slowly, overfill, or leak water into the drum when off — sometimes accompanied by an FE error code. 120V, 60Hz, 1 inlet, 4 outlets. Replaces 5220FR2008C, 1345045, AH3527429, EA3527429, OEM13323375, AP4441122, ALG312490, PD00001833, PS3527429. Some LG steam washers use this valve alongside a separate hot water valve — if only one side is failing, you may only need to replace the specific valve at fault rather than the whole group. Common Problems This Part Fixes Washer continues filling with water even after it should be full Washer filling slowly Washer overfilling Water leaking into the drum when the washer is turned off FE error code displayed during the fill portion of the cycle Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer water inlet valve directly replaces the following OEM and cross-reference part numbers: 5220FR2008C, 1345045, AH3527429, EA3527429, OEM13323375, AP4441122, ALG312490, PD00001833, PS3527429 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water inlet valve is compatible with select LG front-load washers, and also fits select Kenmore washers built on the LG platform. Note: LG uses several visually similar water valves across its washer lineup, including 5220FR2006H and 5221ER1003S. This part is also closely related to our 5220FR2008C cold water inlet valve listing — some model listings note that either may fit depending on the exact production run, but they are separate part numbers. Always confirm your exact part number — comparing your old valve's printed number and photo against the listing is the most reliable way to avoid ordering a similar-looking but incorrect valve. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement water inlet and dispenser valve assembly Resolves "won't stop filling," "fills slowly," "overfills," "leaks when off," and "FE error code" symptoms 1 inlet, 4 outlets Rated 120V, 60Hz Sold individually Direct drop-in replacement — matches the original mounting and hose connections Replaces 1345045, AH3527429, EA3527429, OEM13323375, AP4441122, ALG312490, PD00001833, PS3527429 Compatible with LG and select Kenmore front-load washers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number XP5220FR2008C OEM Part Number 5220FR2008C Part Type Washer Water Inlet & Dispenser Valve Assembly Condition Aftermarket Replacement Application Front-Load Washers Voltage 120V Frequency 60 Hz Inlets / Outlets 1 inlet, 4 outlets Weight Approx. 0.60 lbs Package Dimensions 5.12" x 4.69" x 3.98" Repair Difficulty Easy to Moderate Quantity 1 valve (sold individually) Compatible Brands LG, Kenmore Installation Notes ⚠️ Shut Off Water Supply And Unplug Washer Before Starting Disconnect power at the outlet or shut off the circuit breaker, and shut off the water supply before beginning. Wear work gloves. Access on most LG front-load washers requires removing the top cover to reach the water valve assembly and its electrical connections and hoses. On models with multiple valves (some LG steam washers use one separate hot water valve plus a group of cold water valves), identify specifically which valve is failing before removing anything — check your old valve's printed part number and compare it against a reference photo, since several LG valves look very similar. Photograph the wiring and hose connections before disconnecting anything. Disconnect the electrical connector and hose from the failing valve, remove its mounting screws, and pull it free. Install the new 5220FR2008C in the same position, reconnect the hose and electrical connector fully, and secure the mounting screws. Restore the water supply and power, then run a full test cycle to confirm correct fill behavior with no leaking or error codes. Tools needed: Phillips screwdriver, pliers, work gloves. Frequently Asked Questions My washer shows an FE error code. Is this the valve I need? Possibly. One customer reported an FE error appearing while the machine was still "filling," which pointed to one of the hot or cold water valves not working correctly. If your FE error consistently appears during the fill portion of the cycle, this valve is a reasonable place to start troubleshooting. My washer has more than one water valve. Do I need to replace all of them? Not necessarily. Some LG steam washers use a separate hot water valve plus a group of valves fed from the cold water main, and it's common for only one specific valve in that group to actually be bad. One customer confirmed this exact setup, testing and replacing only the single failing valve rather than the entire group, which resolved their issue. How do I make sure I'm ordering the correct valve, since several look similar? Check the part number printed directly on your old valve and compare it, along with a photo if available, against the listing before ordering. One customer specifically noted that several LG valves looked alike, and having a clear reference photo was what let them positively identify the correct replacement. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine LG OEM part, but is manufactured to match the solenoid design, inlet/outlet configuration, and electrical rating of the original 5220FR2008C valve used in compatible LG and Kenmore front-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

Genuine Whirlpool OEM Part Whirlpool WP91939 Washer Genuine OEM Upper Transmission Shaft Seal Factory OEM upper transmission shaft/oil seal for select Whirlpool-built direct-drive washers. Product Overview The Whirlpool WP91939 Upper Transmission Shaft Seal is a Genuine OEM washer seal installed at the top of the transmission shaft where the shaft enters the tub area. It acts as a barrier to help prevent wash water from entering the transmission/gearcase assembly. A worn or damaged seal can contribute to water leakage around the transmission shaft area. Quick Answer WP91939 is the Genuine Whirlpool OEM upper transmission shaft seal, also commonly described as an oil seal or transmission shaft seal. It replaces earlier numbers including 91939, 17248, 18918, 92939, and 99835. Common Problems This Part May Fix Water leaking around the transmission shaft Moisture reaching the transmission/gearcase area Visible deterioration of the upper shaft seal Water pooling beneath a direct-drive washer Seal replacement during transmission or centerpost service Replaces and Cross-References WP91939, 91939, 17248, 18918, 3154, 92939, 99835, J27-501, LP632, AP6013637, EAP11746864, AWP48904, PD00005395, PS11746864. Cross-reference numbers are supplied for identification. Always verify the complete appliance model number before ordering. Compatibility Used on select Whirlpool-built direct-drive washers sold under Whirlpool, Kenmore, Estate, Roper, KitchenAid, Crosley, and Inglis brands. Confirmed model examples include: CAE2792AW0 ETW4400WQ1 RAL5144BQ1 110.15942401 110.22912100 110.24922202 110.92587410 110.72785720 Important: This is only a partial compatibility list. Whirlpool has used several different seals in similar-looking washers. Verify the complete model number and original part number before purchase. Key Features Genuine Whirlpool OEM replacement part Upper transmission shaft/oil seal Helps keep wash water out of the transmission For select Whirlpool-built direct-drive washers Factory replacement for multiple earlier seal numbers Product Specifications Manufacturer Part Number WP91939 Brand Whirlpool Part Type Upper Transmission Shaft Seal / Oil Seal Condition New Part Quality Genuine OEM Approx. Diameter 1 in. Approx. Height 1/2 in. Application Washer transmission shaft sealing Package Quantity 1 Seal Installation Notes Unplug the washer and shut off both water-supply valves before service. Follow the appliance service procedure to access the transmission/shaft area. Remove the old seal carefully without damaging the shaft or surrounding sealing surface. Clean the shaft and seal seat before installing the new seal. Install the replacement seal squarely and to the same position/orientation as the original. Inspect nearby tub, centerpost, spin-shaft, and transmission seals while the washer is disassembled. Service note: This repair can require substantial washer disassembly. If there is corrosion, shaft wear, transmission oil leakage, or centerpost damage, additional parts may be required. Frequently Asked Questions Is WP91939 a Genuine Whirlpool OEM part? Yes. WP91939 is manufactured by Whirlpool as an Original Equipment Manufacturer replacement seal. What does the WP91939 seal do? It seals around the upper transmission shaft to help prevent wash water from entering the transmission/gearcase area. Does WP91939 replace 91939? Yes. WP91939 is the current Whirlpool replacement for original part number 91939 and several earlier numbers. Is WP91939 the same as WP8577376? No. They are different seals used at different locations in the washer sealing system. Order by the complete washer model number and required seal position. Shop With Confidence Verify your complete washer model number before ordering. Genuine OEM WP91939 is designed for specified Whirlpool-built washer applications. Genuine Whirlpool OEM Upper Transmission Seal Direct-Drive Washer Applications Compatibility Support

Read more less

5304524452 Washer Genuine OEM Drain Pump Assembly The 5304524452 is a genuine Frigidaire OEM drain pump assembly for Frigidaire stacked laundry center (washer/dryer combo) units, and also fits select Crosley, Electrolux, Gibson, Kelvinator, Westinghouse, and Kenmore models. This pump removes wash water from the tub at the end of each cycle, draining it out before the washer refills with fresh water for rinses. Common causes of a failing pump include normal wear and tear over time, an obstructed drain line, or issues with the pump housing or impeller. Symptoms of a bad pump assembly include incomplete draining of water at the end of cycles, water pooling in the tub, or the washer failing to advance through its cycle because it can't clear the water. It directly replaces 4246239, 4839543, 4959972, 5304500535, 5304515673, A03077601, AP5962219, AP6333076, AFR19009, AP6989734, BPX401-13J, EAP11703882, EAP12365991, EAP16218540, PD00063454, PS16218540. Quick Answer The 5304524452 Washer Genuine OEM Drain Pump Assembly fixes Frigidaire, Crosley, Electrolux, Gibson, Kelvinator, Westinghouse, and Kenmore stacked laundry center units where the washer won't drain, water pools in the tub, or the cycle won't advance past the drain step. Replaces 4246239, 4839543, 4959972, 5304500535, 5304515673, A03077601, AP5962219, AP6333076, AFR19009, AP6989734, BPX401-13J, EAP11703882, EAP12365991, EAP16218540, PD00063454, PS16218540. Several sources note that some replacement drain pumps look similar to this one but aren't the same part — check your original pump's model number or your washing machine's model number carefully before ordering. Common Problems This Part Fixes Washer not draining at the end of a cycle Water pooling or standing in the tub after a completed cycle Washer failing to advance past the drain step Incomplete draining leaving damp or soaked clothes Pump making unusual noise from a damaged impeller Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer drain pump assembly directly replaces the following OEM and cross-reference part numbers: 5304524452, 4246239, 4839543, 4959972, 5304500535, 5304515673, A03077601, AP5962219, AP6333076, AFR19009, AP6989734, BPX401-13J, EAP11703882, EAP12365991, EAP16218540, PD00063454, PS16218540 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drain pump assembly is compatible with select Frigidaire stacked laundry center units, and also fits select Crosley, Electrolux, Gibson, Kelvinator, Westinghouse, and Kenmore combo units built on the same platform, including model numbers such as CFLE3900UW0, CFLE3900UW1, CFLE3900UW3, FFLE3900UW0, FFLE3900UW1, FFLE3900UW2, FFLE3900UW3, FFLE3911QW0, FFLE3911QW1, FFLE39C1QW0, FFLE4033QT0, FFLE4033QW0, FFLE40C3QT0, FFLE40C3QW0, FFLG3900UW0, FFLG3900UW1, FFLG3900UW2, FFLG3900UW5, FFLG3911QW0, FFLG3911QW1, FFLG3911QW2, FFLG4033QT0, FFLG4033QT1, FFLG4033QW0, FFLG4033QW1, SFLG3911RW0, SFLG3911RW1, SFLG4033RT0, SFLG4033RT1, SFLG4033RW0, SFLG4033RW1, and Kenmore 417.61712510, 417.61712511, 417.61722510, 417.61723510, 417.61732810, 417.61733810, 417.71712510, 417.71712511, 417.71722510, 417.71722511, 417.71723510, 417.71723511, 417.71732810, and 417.71733810. Note — similar-looking but different pumps exist: Some replacement drain pumps are visually similar to this one but aren't compatible. Check your original pump's model number or your washing machine's model number carefully before ordering. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine Frigidaire OEM part — factory-specified pump housing and impeller design Drains wash water from the tub at the end of each cycle Resolves "won't drain," "water pooling," and "won't advance past drain step" symptoms Direct drop-in replacement matching the original mounting and hose connections Replaces 4246239, 4839543, 4959972, 5304500535, 5304515673, A03077601, AP5962219, AP6333076, AFR19009, AP6989734, BPX401-13J, EAP11703882, EAP12365991, EAP16218540, PD00063454, PS16218540 Compatible with Frigidaire, Crosley, Electrolux, Gibson, Kelvinator, Westinghouse, and Kenmore laundry center units Genuine OEM replacement — guaranteed fit, materials, and performance Simple DIY repair with basic tools Product Specifications Part Number 5304524452 Part Type Washer Drain Pump Assembly Condition Genuine OEM Brand Frigidaire Application Stacked Washer/Dryer Laundry Centers Function Drains wash water from the tub at the end of each cycle Repair Difficulty Easy Quantity 1 drain pump assembly Compatible Brands Frigidaire, Crosley, Electrolux, Gibson, Kelvinator, Westinghouse, Kenmore Installation Notes ⚠️ Unplug The Laundry Center And Shut Off Water Supply Before Starting Disconnect power to the laundry center unit and shut off the water supply before beginning. Wear work gloves and have towels ready for any residual water. Access the pump, typically located at the bottom front or rear of the washer section depending on your model. Remove the clamp attaching the hose to the old pump, then remove the hose. Remove the three screws holding the pump to the washer. Take out the old pump. Install the new 5304524452 in the same position and secure it with the three mounting screws. Reattach the hose to the new pump and secure the clamp. Restore the water supply and power, then run a test cycle to confirm the washer drains completely with no leaks. Tools needed: pliers, screwdriver, work gloves. Frequently Asked Questions My washer isn't draining. Is this the part I need? Yes, this is the most direct symptom of a failed drain pump. Since this pump is responsible for removing wash water from the tub at the end of each cycle, a worn impeller or internal failure can leave water standing in the tub and prevent the washer from advancing to the next stage of the cycle. Is this a difficult repair? No, one customer described it as an easy removal and installation: remove the clamp attaching the hose to the pump, remove the hose, remove the three screws holding the pump to the washer, then reverse the process with the new pump. How do I make sure I'm ordering the correct pump, since some look similar? Check the model number printed on your original pump, or your washing machine's full model number, before ordering. Multiple sources note that some replacement drain pumps look visually similar to this one but aren't actually compatible, so matching your specific part or model number is the reliable way to confirm fit. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Frigidaire to factory specifications — guaranteed fit, materials, and performance. It matches the original pump housing, impeller, and connection type of the drain pump assembly originally installed in your washer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

5220FR2006H Washer Genuine OEM Water Inlet Valve (Hot) The 5220FR2006H is a genuine LG OEM hot water inlet valve for LG front-load washers, and also fits select Kenmore models. This valve connects to your home's hot water line and controls the flow of hot water into the tub during the fill portion of each cycle, opening as the cycle calls for hot water and closing once the correct fill level and temperature mix are reached. The valve has a standard hose fitting inlet and a single water outlet. Common causes of failure include mineral or sediment buildup inside the valve body and general electrical wear in the solenoid. Symptoms of a failing valve include the washer not filling, not stopping when it should, not starting, leaking water, not washing properly, no hot water reaching the tub, or an IE error code displayed on the control panel. It directly replaces 1268123, 5220FR1280F, 5220FR2006L, 5220FR2006Q, AP4441935, ALG51717, AH3527427, EA3527427, EAP3527427, PD00001765, PS3527427. Quick Answer The 5220FR2006H Washer Genuine OEM Water Inlet Valve (Hot) fixes LG and select Kenmore front-load washers with no hot water, won't fill, won't stop filling, won't start, leaking, or an IE error code. Standard hose fitting inlet, 1 outlet. Replaces 1268123, 5220FR1280F, 5220FR2006L, 5220FR2006Q, AP4441935, ALG51717, AH3527427, EA3527427, EAP3527427, PD00001765, PS3527427. This is the hot water valve — a separate but related cold water valve is used alongside it. If both valves are original and the same age, consider replacing both together while you have the washer open. Common Problems This Part Fixes No hot water reaching the tub Washer not filling with water Washer not stopping fill when it should Washer not starting Water leaking from the valve area IE error code displayed on the control panel Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer hot water inlet valve directly replaces the following OEM and cross-reference part numbers: 1268123, 5220FR1280F, 5220FR2006L, 5220FR2006Q, AP4441935, ALG51717, AH3527427, EA3527427, EAP3527427, PD00001765, PS3527427 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This hot water inlet valve is compatible with select LG front-load washers, and also fits select Kenmore washers built on the LG platform, including model numbers such as WM2240CW, WM2250CW, WM2277HW, WM3170CW, WM3250HV, 40272, 40441 (ABWESEU), 41002, 41003, 41172 (ABWEPEU), 41172 (ABWESEU), 41182, 41262 (ABWEPEU), 41262 (ABWEVEU), and 41283. Note: This is the hot water valve. Our 5220FR2008C listing is the related cold water valve, and our 5220FR2008F listing is a closely related water inlet and dispenser valve assembly used on other models — these are separate parts serving different roles or platforms. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which valve your washer needs. Key Features Genuine LG OEM part — factory-specified solenoid design and flow rate Regulates hot water flow into the tub during fill Resolves "no hot water," "won't fill," "won't stop filling," "won't start," "leaking," and "IE error code" symptoms Standard hose fitting inlet, 1 water outlet Direct drop-in replacement — matches the original mounting and hose connections Replaces 1268123, 5220FR1280F, 5220FR2006L, 5220FR2006Q, AP4441935, ALG51717, AH3527427, EA3527427, EAP3527427, PD00001765, PS3527427 Compatible with LG and select Kenmore front-load washers Genuine OEM replacement — guaranteed fit, materials, and performance Simple 15-minute DIY repair Product Specifications Part Number 5220FR2006H Part Type Washer Hot Water Inlet Valve Condition Genuine OEM Brand LG Application Front-Load Washers Inlet Standard hose fitting Outlet 1 Related Part 5220FR2008C cold water valve (sold separately) Repair Difficulty Easy — approx. 15 minutes Quantity 1 valve Compatible Brands LG, Kenmore Installation Notes ⚠️ Shut Off Water Supply And Unplug Washer Before Starting Turn off the water supply and unplug the washing machine from the wall before beginning. Wear work gloves. Locate the top cover of your washer — depending on your model, it may be located along the side or in the back — and use a flat-blade screwdriver to gently pry it off. Locate the hot water valve and disconnect the water supply hose from it, using locking pliers to loosen the hose clamp before carefully pulling the hose away. Unscrew the screws holding the valve in place and gently remove it from the washer. Mount the new 5220FR2006H valve in place and replace the screws. Reconnect the water supply hose to the valve and tighten the hose clamp using locking pliers. Turn the water supply back on and plug the washer back in. Test the new valve by running a load of laundry and checking for any leaks. Tools needed: flat-blade screwdriver, locking pliers, work gloves. Frequently Asked Questions My washer isn't getting hot water. Is this the part I need? Yes, this is the most direct symptom of a failed hot water inlet valve. Since this valve is what admits hot water from your household supply into the washer, a solenoid failure or internal blockage can prevent hot water from entering properly, even if cold water fill still works normally. My washer shows an IE error code. Could this valve be the cause? Yes, an IE error code on LG washers is commonly tied to a fill issue, and a failed inlet valve — hot or cold — is one of the most frequent causes. Confirm which side (hot or cold) is actually affected before ordering, since these are separate parts. Should I replace the cold water valve at the same time? It's worth considering, especially if both valves are the same age. One customer specifically purchased both the hot and cold water inlet valves together during a single repair, along with a new drain pump motor, rather than tackling each part separately over multiple repairs. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by LG to factory specifications — guaranteed fit, materials, and performance. It matches the original solenoid design, flow rate, and connection type of the hot water inlet valve originally installed in your washer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

W10467289 Washer Genuine OEM Temperature Sensor Replaces Part Numbers: WPW10467289, W10467289, 2629420, 8181705, 8182291, 8540225, 8540226, W10176658, W10176659, OEM18065663, AP6021886,, PS11755214. Description: This Water Temperature Sensor is a Genuine OEM part for specific Kenmore, Whirlpool washing machine models. This sensor ensures the water is reaching the proper temperature at each stage of the wash cycle.   California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

XPARTCO W10734521 Washer Clutch Slider Kit The XPARTCO W10734521 is an aftermarket replacement washer clutch slider kit compatible with a wide range of Whirlpool, Maytag, Kenmore, KitchenAid, Amana, Crosley, Estate, Jenn-Air, Roper, Magic Chef, Admiral, and Kirkland HE top-load washers. The clutch slider kit is part of the drive system that engages and disengages the inner tub from the gearcase — it's responsible for transitioning the washer between agitation and spin modes. The slider gear works together with the electromagnetic clutch and gearcase to move the inner tub during the wash and spin portions of every cycle. When the slider or its spring fails, the washer typically won't spin properly, won't agitate, makes grinding noise, or leaves clothes soaking wet at the end of a cycle. This kit includes the slider, spring support, 30mm spiral, and bolt. Slider dimensions: 2-7/8" outer diameter x 7/8" deep. Support spring: 1-5/8" outer diameter x 1-1/8" long. Spiral: 1-5/16" outer diameter. Bolt: 7/8" head diameter x 1" high. Construction is metal and plastic in black, white, and gray. Important: this is the slider kit only — it does NOT include the electromagnetic clutch (sold separately as W10754448). The current W10734521 part number supersedes the earlier W10006484, W10006494, W10275082, W10447975, and W10905025. It also replaces 3452506, AP5952873, EAP10060062, PD00025495, and PS10060062. Installs in 60–90 minutes with basic hand tools. Quick Answer The XPARTCO W10734521 Washer Clutch Slider Kit fixes Whirlpool, Maytag, Kenmore, KitchenAid, and related HE top-load washers that won't spin or agitate properly, won't transition between cycle phases, leave clothes soaking wet, or make grinding noise during the spin cycle. Slider kit only — electromagnetic clutch (W10754448) is sold separately. Includes slider (2-7/8" OD), spring support (1-5/8" OD), 30mm spiral, and bolt. Replaces W10006484, W10006494, W10275082, W10447975, W10905025, 3452506, AP5952873, EAP10060062, PD00025495, PS10060062. Common Problems This Part Fixes Washer won't spin or spins very slowly — slider not engaging the gearcase for spin mode Washer won't agitate — slider not transitioning the drive system to agitation mode Clothes left soaking wet at the end of the cycle — incomplete spin Grinding, rattling, or clunking noise during the spin or agitation phase Washer fills and drains normally but never spins or agitates Worn or broken slider gear teeth visible on the drive assembly Weak or broken slider spring — washer drive losing positive engagement Repeated cycle interruptions in the spin or agitation portion of cycles What's in the Kit Part 1 Slider Gear 2-7/8" outer diameter x 7/8" deep · Slides over the drive assembly shaft to engage/disengage the gearcase for agitation and spin transitions · Install with the teeth facing outward Part 2 Spring Support 1-5/8" outer diameter x 1-1/8" long · Provides return tension for the slider · Replace whenever the gearcase or slider is replaced — spring can weaken over time Part 3 30mm Spiral 1-5/16" outer diameter · Spiral retaining component that holds the slider assembly together on the drive shaft Part 4 Bolt 7/8" head diameter x 1" high · Secures the assembly Replaces Part Numbers This clutch slider kit directly replaces the following OEM and cross-reference part numbers: W10734521, 3452506, W10006484, W10006494, W10275082, W10447975, AP5952873, AWP41487, EAP10060062, PD00025495, PS10060062. W10734521 is the current production part superseding W10006484, W10006494, W10275082, W10447975, and W10905025. Contact our support team with your model number if you need confirmation before ordering. Compatibility This clutch slider kit is compatible with select HE top-load washers from the following brands: Whirlpool top-load washers (Cabrio, WTW5000, WTW5500, WTW5700, WTW6000, WTW6200, WTW6400, WTW7000, WTW7120, WTW8000, WTW8200, WTW8500, WTW8700 series and related models) Maytag top-load washers (Bravos and Centennial series and related models) Kenmore / Sears top-load washers (Whirlpool-built — select 110-series and related models) KitchenAid top-load washers (select models) Amana top-load washers (select models) Crosley top-load washers (select models) Estate top-load washers (select models) Jenn-Air top-load washers (select models) Roper top-load washers (select models) Magic Chef top-load washers (select models) Admiral top-load washers (select models) Kirkland top-load washers (select models) Important — Slider Kit Only, NOT Clutch: This is the clutch slider kit (slider, spring, spiral, bolt) — it does not include the electromagnetic clutch assembly. The electromagnetic clutch is part number W10754448 and is sold separately. If you need both components, order each part separately. Many repair scenarios call for replacing both at the same time, since both wear together. Always verify your model number and confirm exactly which component has failed before ordering. Key Features Complete slider repair kit — slider, spring support, 30mm spiral, and bolt included as a matched set Works with the electromagnetic clutch and gearcase to drive the inner tub during agitation and spin modes Resolves "won't spin," "won't agitate," and "clothes left soaking wet" symptoms when the slider has worn or the spring has weakened Current production part number — supersedes W10006484, W10006494, W10275082, W10447975, and W10905025 Slider: 2-7/8" outer diameter x 7/8" deep · Spring: 1-5/8" OD x 1-1/8"L · Spiral: 1-5/16" OD · Bolt: 7/8" head x 1"H Metal and plastic construction in black, white, and gray Important: slider kit only — electromagnetic clutch (W10754448) sold separately For full performance, replace all components in the kit together as a set Compatible with Whirlpool, Maytag, Kenmore, KitchenAid, Amana, Crosley, Estate, Jenn-Air, Roper, Magic Chef, Admiral, and Kirkland HE top-load washers Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 60–90 minutes with basic hand tools Product Specifications Part Number W10734521 Supersedes W10006484, W10006494, W10275082, W10447975, W10905025 Part Type Washer Clutch Slider Kit Condition Aftermarket Replacement Application HE Top-Load Washers (Whirlpool platform) Includes 1x Slider, 1x Spring Support, 1x 30mm Spiral, 1x Bolt Slider Dimensions 2-7/8" Outer Diameter x 7/8" Deep Spring Support Dimensions 1-5/8" Outer Diameter x 1-1/8" Long Spiral Dimensions 1-5/16" Outer Diameter Bolt Dimensions 7/8" Head Diameter x 1" High Material Metal / Plastic Color Black / White / Gray Electromagnetic Clutch NOT included — see W10754448 (sold separately) Compatible Brands Whirlpool, Maytag, Kenmore, KitchenAid, Amana, Crosley, Estate, Jenn-Air, Roper, Magic Chef, Admiral, Kirkland Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting — Wear Work Gloves Disconnect power and turn off the water supply before beginning. Place towels under the washer — some residual water may spill from hoses during disassembly. Wear work gloves to protect your hands. Unthread the hot and cold water supply hoses from the inlet valve ports. Disconnect the drain hose from the outlet port using channel-lock pliers to release the spring clamp. Carefully tip the washer onto its side or back on a padded surface to access the underside. Disconnect the wiring harnesses to the drive motor and pull the rotor free — be prepared for some resistance, as the permanent magnets in the rotor require some effort to remove. Use a small awl inserted between the slider gear teeth to release the spring retainer. With the retainer released, pull off the old spring and slider gear. Note the orientation of the slider — teeth facing outward. Install the new W10734521 components in sequence: slide the new slider gear onto the drive assembly shaft with teeth facing outward, install the new spring support and 30mm spiral, and secure with the new bolt. Reinstall the rotor (the magnets will pull it into place), reconnect the wiring harnesses, return the washer to upright, reconnect supply hoses and drain hose, restore power and water, and test the spin cycle for proper function. Tools needed: Phillips screwdriver, socket set, channel-lock pliers, small awl, padded surface for tipping, work gloves. Frequently Asked Questions What's the difference between W10734521 and W10754448? These are two different parts in the same drive system. The W10734521 is the clutch slider kit — it includes the slider gear, spring support, spiral, and bolt that physically engage/disengage the inner tub from the gearcase to transition between agitation and spin modes. The W10754448 is the electromagnetic clutch itself — the electrical component that drives the engagement. Both can fail independently, and many repair scenarios call for replacing both at the same time since they work together. Confirm exactly which component has failed before ordering, or order both if you're rebuilding the drive system as a full repair. My washer won't spin — is it the slider or something else? A washer that won't spin can have several causes: a failed slider kit, a failed electromagnetic clutch (W10754448), a damaged drive belt, a failed motor or rotor, a broken lid switch, or — on some models — a failed gearcase. The slider kit is one of the more common causes when the symptom is "fills and drains but won't spin" with no obvious noise or burning smell. Before replacing the slider, check that the lid latch strike (W11457841 on some models) is engaging properly, the drive belt is intact, and the motor is functioning. If those check out and the slider gear shows visible wear, missing teeth, or a stretched spring, the W10734521 kit is the right repair. Should I replace all parts in the kit together? Yes — for the kit to perform as designed, all components should be replaced as a matched set. The slider, spring support, spiral, and bolt all work together — if one is worn, the others have typically experienced the same load and wear. Reusing old components alongside new ones can cause premature failure of the new parts and a repeat repair. The W10734521 kit is priced and packaged for a complete replacement, so install all four pieces during your repair. What is the difference between W10734521 and the older part numbers it replaces? W10734521 is the current production version of this slider kit. It directly supersedes W10006484, W10006494, W10275082, W10447975, and W10905025 — all of which were earlier OEM part numbers for variations of the same slider kit across production revisions. Whirlpool consolidated these into the W10734521 to streamline the parts catalog. If your washer's parts diagram shows any of these older numbers, the W10734521 is the correct current replacement. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured from metal and plastic to match the dimensions, gear profile, and drive engagement function of the original W10734521 clutch slider kit used in compatible Whirlpool, Maytag, Kenmore, and related HE top-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

DC62-00266G Washer Water Inlet Valve Cold Side Water Valve Fits specific Samsung washer models. Description: This Water Inlet Valve is a replacement part for specific Samsung washing machine models. It controls the flow of water into the washer during the fill cycles, ensuring the proper amount of water is delivered for each wash load. This valve opens and closes to allow water to enter the tub from the household water supply, making it a critical component for the washing machine's operation. Replaces Part Numbers:DC62-00266G, AP5966622, PS11719652   This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

XPARTCO WH01X20826 Washing Machine Shock Absorber The XPARTCO WH01X20826 is an aftermarket replacement shock absorber (damper) for GE front-load washers. The wash tub inside a front-load washer hangs suspended inside the cabinet, and a set of these shock absorbers is what controls that movement — dampening the tub's vibration and motion during spin so it doesn't bang against the cabinet or shake the whole machine. These washers typically use four shock absorbers working together around the tub, and this listing is for a single individual shock absorber. Over time the internal damping material in these shocks wears out, or the shock can physically separate from its mounting point — something that can also happen if the washer is moved or shifted without the tub properly secured first. Because all four shocks on a given washer are typically the same age and under the same stress, if one has failed the others are often not far behind — many technicians recommend ordering four of this same part and replacing the full set together as a preventative measure. A worn or detached shock absorber produces a very recognizable symptom: excessive vibration, shaking, or banging noise during the spin cycle, sometimes strong enough that the washer visibly moves or "walks" across the floor. It directly replaces WH01X20826, AGE25988, AP5982139, AGE25988, EAP11701130, PD00037528, PS11701130. Quick Answer The XPARTCO WH01X20826 Washing Machine Shock Absorber fixes GE front-load washers (and select Hotpoint, Haier, Monogram, Café, and Kenmore models built on the GE platform) that vibrate, shake, or bang excessively during spin, or seem to "walk" across the floor. Sold as a single individual shock absorber. Replaces WH01X20826, AGE25988, AP5982139, AGE25988, EAP11701130, PD00037528, PS11701130. These washers use four shock absorbers total — if one has failed, order four of this part to replace the full set, since they wear on the same schedule. Common Problems This Part Fixes Excessive vibration or shaking during the spin cycle Loud banging or knocking noise from inside the cabinet during spin Washer that seems to "walk" or move across the floor during operation Tub striking the cabinet frame or nearby panels Shock absorber that has visibly separated or detached from its mounting point Noise or vibration that started or worsened after the washer was moved or relocated Visible wear, cracking, or looseness in the shock absorber material Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washing machine shock absorber directly replaces the following OEM and cross-reference part numbers: WH01X20826, AGE25988, AP5982139, AGE25988, EAP11701130, PD00037528, PS11701130 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This shock absorber is compatible with select GE front-load washers, and also fits select Hotpoint, Haier, Monogram, and Café washers built on the GE platform. Note: GE uses several different shock absorber part numbers across its washer lineup, including separate parts such as WH01X10727 and WH03X29516 for other platforms. This WH01X20826 shock is specific to the front-load models listed above and is not interchangeable with those other GE shocks. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement shock absorber — dampens tub vibration and movement during spin Sold individually — order four to replace the full set on a typical front-load washer Resolves "excessive vibration," "banging or knocking noise," and "washer walking across the floor" symptoms caused by worn or detached shocks Durable plastic and rubber construction for long-term damping performance Direct drop-in replacement — no modification required Replaces WH01X20826, AGE25988, AP5982139, AGE25988, EAP11701130, PD00037528, PS11701130. Compatible with GE, Hotpoint, Haier, Monogram, Café, and select Kenmore front-load washers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number XPWH01X20826 OEM Part Number WH01X20826 Part Type Washing Machine Shock Absorber (Damper) Condition Aftermarket Replacement Application GE Front-Load Washers Material Plastic and rubber Function Dampens tub vibration and movement during spin Typical Quantity Per Washer 4 (this listing is for 1 individual shock) Quantity 1 shock absorber Compatible Brands GE, Hotpoint, Haier, Monogram, Café, Kenmore Installation Notes ⚠️ Unplug Washer Before Starting — Consider Replacing All Four Shocks Together Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access to the shock absorbers typically requires removing the top and/or front panel of the washer to reach the tub suspension points — check your model's service diagram, since access varies. Photograph how each old shock absorber connects to the frame and the tub before removing anything, since these components are symmetrical around the tub and easy to reverse or mismatch. Disconnect the old shock absorber from its mounting point at both the frame and tub ends, and remove the mounting pin. Install the new shock absorber in the same position with its mounting pin, matching the original orientation. If you're only replacing one shock, be aware the remaining three original shocks are the same age and under the same stress — many technicians recommend ordering three more of this same part and replacing all four together to avoid reopening the washer again soon after. Once installed, gently rock the tub by hand to confirm even resistance at each corner before reassembling the panels. Restore power and run a full spin cycle to confirm the vibration, shaking, or banging noise has resolved. Tools needed: Phillips screwdriver, nut driver, work gloves. Frequently Asked Questions Do I need to order more than one of these? This listing is for a single shock absorber, but GE front-load washers use four of them working together around the tub. If one has failed, it's strongly worth ordering four total and replacing the full set, since all four are typically the same age and have been under the same stress — replacing just one risks having to reopen the washer again soon after for the next one. My washer started shaking right after I moved it to a new spot. Is that related? Yes, this is a documented cause of shock absorber problems on this platform. If the tub wasn't properly secured or the washer was tilted significantly during a move, one or more shock absorbers can separate from their mounting point. Check that all four shocks are still properly connected at both ends before assuming a shock itself has failed — sometimes reseating a separated shock is all that's needed, though if it shows wear it's worth replacing regardless. How much vibration is normal, and how do I know it's actually the shocks? Some vibration during high-speed spin is normal, especially with an unbalanced load. But vibration strong enough to move the washer across the floor, or accompanied by a banging or knocking noise from inside the cabinet, points to a suspension problem rather than a simple unbalanced load. Try redistributing the laundry evenly in the drum and running the spin cycle again — if the shaking persists with a balanced load, inspect the shock absorbers for wear, cracking, or separation. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured to match the dimensions, mounting configuration, and damping performance of the original WH01X20826 shock absorber used in compatible GE, Hotpoint, Haier, Monogram, Café, and Kenmore front-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

Genuine Whirlpool OEM Whirlpool WP8577376 Washer Genuine OEM Transmission Shaft Seal Factory replacement transmission stem / agitator shaft seal for select Whirlpool-built top-load washers. Product Overview WP8577376 is a Genuine Whirlpool OEM washer shaft seal. Whirlpool describes it as a washing machine transmission stem seal, while Sears identifies it as an agitator shaft seal. The seal helps prevent wash water from leaking between the tub mounting stem and the agitator drive shaft, protecting the transmission/drive area from moisture. Quick Answer WP8577376 is the current Genuine Whirlpool OEM replacement for several older washer shaft and center-post seals. It is commonly used on older Whirlpool-built direct-drive top-load washers. Common Problems This Part May Fix Water leaking around the agitator or center-post area Moisture reaching the transmission or drive system Worn, cracked, hardened, or missing shaft seal Leak discovered during tub or transmission service Replaces and Cross-References WP8577376, WP91938, 8577376, 91938, 1181094, 356934, 356934BULK, 356934D, 99404, J27-500, J27-661, LP630, LP631, AP6013521, AWP49388, PD00005095, PS11746747 Cross-reference numbers are provided for identification. Always verify the complete appliance model number before ordering. Compatibility Fits select Whirlpool-built washers sold under Whirlpool, Kenmore, KitchenAid, Roper, Estate, Crosley, Admiral, Amana, Magic Chef, Maytag and related brands. Compatible model examples include: LSR7233DZ1 LSQ8243HQ0 LSQ8512KQ0 LSQ8543JQ0 LSQ9110PW3 LSQ9544KQ0 LSQ9549LG1 110.10502990 110.16602690 110.73875800 110.71770610 110.73775200 Important: This is only a partial compatibility list. Verify the full washer model number and original seal number before purchase. Key Features Genuine Whirlpool OEM replacement part Transmission stem / agitator drive shaft sealing function Helps prevent water intrusion into the drive area Updated replacement for multiple older shaft-seal numbers Designed for select Whirlpool-built top-load washers Product Specifications Manufacturer Part Number WP8577376 Brand Whirlpool Part Type Transmission Stem / Agitator Shaft Seal Condition New Part Quality Genuine OEM Application Washer Tub / Transmission Shaft Sealing Package Quantity 1 Shaft Seal Installation Notes Unplug the washer and shut off both water-supply valves before service. Drain any remaining water and follow the appliance service procedure for tub/drive-system access. Remove the old shaft seal without damaging the mounting surface or drive shaft. Clean the sealing surface before installing the replacement. Install the new seal in the correct orientation and reassemble the washer. Run a test cycle and inspect carefully for leaks. Service note: A leak in this area can also involve worn tub seals, a damaged mounting stem, corrosion, or transmission/shaft wear. Inspect related components while the washer is disassembled. Frequently Asked Questions Is WP8577376 a Genuine Whirlpool OEM part? Yes. WP8577376 is a Genuine Whirlpool OEM replacement shaft seal. What does this seal do? It helps prevent water from leaking between the tub mounting stem and agitator drive shaft. Does WP8577376 replace 8577376 and 91938? Yes. Those are among the earlier part numbers superseded by WP8577376. Is this the complete transmission? No. This listing is for the shaft seal only. The transmission/gearcase and other seals are not included. Shop With Confidence Use your washer's complete model number to confirm fitment before ordering. Genuine Whirlpool OEM Factory Replacement Compatibility Support Fast U.S. Shipping

Read more less

Genuine OEM Whirlpool Washer Part WP3951632 Washer Genuine OEM Lower Agitator The lower agitator base moves back and forth during the wash cycle to help circulate clothing through the water and detergent. Product Overview The Whirlpool WP3951632 Washer Lower Agitator is the lower half, or base, of the agitator used in compatible top-load washing machines. During the wash cycle, the agitator moves back and forth to circulate clothing through the wash water and detergent for effective cleaning. This is a new Genuine OEM Whirlpool replacement part manufactured to the original equipment specifications for proper fit and operation in compatible models. Quick Answer WP3951632 is the Genuine OEM Whirlpool lower agitator base for select top-load washers. It replaces part number 3951632. This listing is for the lower agitator only; the upper agitator, agitator dogs, cam, cap, bolt, dispenser, and other hardware are not included unless specifically shown in the product photographs. Common Problems This Part May Fix Washer fills and runs but clothing is not agitated properly Lower agitator does not move during the wash cycle Cracked, broken, or damaged agitator fins Worn or stripped center connection on the agitator base Agitator slips on the transmission shaft Poor washing or uneven clothing movement Replaces and Cross-References WP3951632, 3951632, 547649, AP6008904, AWP47252, EAP11742045, PD00004360, PS11742045. WP3951632 is the current manufacturer part number. Other numbers shown are previous manufacturer or retailer cross-reference numbers used to identify the same lower agitator. Compatibility Designed for select Whirlpool-built top-load washers, including certain models sold under the Whirlpool, Amana, Crosley, Estate, Inglis, and Kenmore brand names. Confirmed model examples include: WTW4800BQ1 WTW4816FW1 WTW4816FW3 WTW4850XQ3 LSQ9010PW3 7MWTW1701DQ1 3RGSC9455JQ1 110.20232711 VAW3584GW0 Important: This is only a partial compatibility list. Agitators can look similar but use different shaft connections, heights, fins, and internal components. Verify the complete washer model number before ordering. Key Features Genuine OEM Whirlpool replacement part Lower agitator base for compatible top-load washers Moves clothing through wash water and detergent Durable molded construction Designed for original fit and operation Direct replacement when WP3951632 is specified Replaces original part number 3951632 Product Specifications Manufacturer Part Number WP3951632 Brand Whirlpool Part Type Washer Lower Agitator / Agitator Base Condition New Quality Genuine OEM Application Top-Load Washing Machine Primary Function Moves clothing through wash water during agitation Included One Lower Agitator Base Installation Notes Unplug the washer before beginning the repair. Remove the fabric-softener dispenser or agitator cap, if installed. Remove the inner cap or seal to access the agitator retaining bolt. Use the correct socket and extension to remove the center retaining bolt. Lift the agitator assembly from the washer and separate the upper agitator from the lower base as required. Inspect the agitator bolt, thrust washer, cam, agitator dogs, upper agitator, and transmission shaft for additional wear. Install the new lower agitator in the same position, tighten the retaining bolt securely, and reinstall all caps or dispenser components. Installation tip: A washer that does not agitate can also have worn agitator dogs, a damaged cam, a loose bolt, a failed drive component, or a transmission problem. Diagnose the appliance before ordering when the cause is uncertain. Frequently Asked Questions Is WP3951632 a genuine Whirlpool part? Yes. WP3951632 is a Genuine OEM Whirlpool replacement lower agitator. Does this listing include the complete agitator assembly? No. This part is the lower agitator base only. The upper agitator, cam, agitator dogs, cap, dispenser, bolt, and related hardware are separate unless specifically shown or stated. What part number does WP3951632 replace? WP3951632 replaces the previous manufacturer part number 3951632. Will this fit every Whirlpool washer? No. It fits only select top-load washer models. Verify your complete model number and required manufacturer part number before purchasing. Should I replace the agitator dogs at the same time? Inspect the agitator dogs and cam while the agitator is disassembled. Replace them separately if they are worn, rounded, cracked, or slipping. Shop With Confidence Purchase the correct Genuine OEM replacement part for dependable fit and performance. Verify your washer model number before ordering, and contact our parts team when compatibility assistance is needed. Genuine OEM WhirlpoolFast U.S. ShippingCompatibility SupportSecure Checkout

Read more less