XPARTCO 131763302 Washer Door Striker
The XPARTCO 131763302 is an aftermarket replacement washer door striker compatible with a wide range of Frigidaire, Electrolux, Kenmore, Crosley, Gibson, Kelvinator, Tappan, and Westinghouse front-load washers — including the Frigidaire Affinity series and a broad set of GLTF, FAFW, FFFW, FFFS, ATF, ATFB, BLTF, CTF, CRTF, FCCW, FRFW, FTF, and FWFB models. The door striker (also called a door strike or door catch) attaches to the inside edge of the washer door and physically enters the lock mechanism on the front panel when the door closes. Once engaged, the strike is what the lock latches onto — and the strike also activates the door switch, signaling the control board that the door is safely closed and the washer can start.
When the striker fails — typically by cracking, chipping, or breaking off from repeated door closures — the washer will not start, will not lock the door, may leak water, or may fail to advance past the fill phase. Gray/red plastic construction, approximately 2.6" x 1.3". This is the current production part number that supersedes many earlier revisions. It directly replaces 131763302, 131763310, 131763300, 131763340, 131763330, 134456600, 134456602, 134456640, 1032664, 1564512, LP3310, PA66-GF25, WH10X10004, AP3580441, AP4508273, AH2378364, AH890617, EA2378364, EA890617, PD00000164, PS2378364, and PS890617. Often replaced together with the matching door lock assembly (131763256, sold separately). Installs in under 5 minutes — no tools required beyond a Phillips screwdriver.
Quick Answer
The XPARTCO 131763302 Washer Door Striker fixes Frigidaire, Electrolux, Kenmore, Crosley, Gibson, Kelvinator, Tappan, and Westinghouse front-load washers where the door won't lock, won't start, won't close properly, leaks water, or won't fill. Gray/red plastic. Approx 2.6" x 1.3". Current production part — supersedes 131763310, 131763300, 131763340, 131763330, 134456600, 134456602, 134456640, 1032664, 1564512, LP3310, PA66-GF25, WH10X10004, AP3580441, AP4508273, AH890617, EA890617, PS890617, AH2378364, PS2378364. Often paired with the door lock assembly (131763256, sold separately).
Common Problems This Part Fixes
Washer door won't latch properly — striker broken or worn down
Washer won't start because the door isn't detected as locked
Washer door won't close — striker missing or damaged
Washer door will not open at the end of the cycle — striker stuck inside the lock
Washer pumps but won't spin — spin cycle blocked by broken striker
Washer won't fill with water — fill cycle blocked by broken striker
Water leaking around the door — door not fully sealing because striker isn't fully engaging
Striker visibly broken, chipped, or missing on the inside edge of the door
Door lock failure — actuator damaged
Replaces Part Numbers
This washer door striker directly replaces the following OEM and cross-reference part numbers:
131763302, 134456600, 131763300, 131763340, 134456602, 134456640, 1564512, AH2378364, EA2378364, EAP2378364, AP4508273, AFR14210, PD00000391, PS2378364.
131763302 is the current OEM production part superseding all listed earlier revisions. Contact our support team with your model number if you need confirmation before ordering.
Compatibility
This door striker is compatible with select front-load washers from the following brands:
Frigidaire front-load washers — Affinity series (FAFW3001LW0-LW7, FAFW3511KW0-KW2, FAFW3801LW0/LW2/LW3/LW4/LW5, FAFW3921NW0/NW1, FAFW4011LW0, FAFW4221LW0)
Frigidaire front-load washers — ATF6000ES0/ES1, ATF6000FS0/FS1/FS2, ATFB6000ES0/ES1, ATFB6000FS0, ATF7000FE0, ATFB7000ES0 series
Frigidaire front-load washers — BLTF2940ES0-ES3, BLTF2940FS0/FS1, BLTF6100FS0 series
Frigidaire front-load washers — FFFS5115PW0, FFFW4000QW0, FFFW5000QW0 series
Frigidaire front-load washers — FRFW3700LW0, FCCW2000LS0, FCCW3000ES0/FS0/FS1/FS2/FS3/FS4 series
Frigidaire front-load washers — FTF1040AS0, FTF1240FS0/FS1, BTF2140FS1, CRTF1240AS0, CRTR9300AS0, CTF140ES0, CTF140FS0/FS1/FS2 series
Frigidaire front-load washers — GLTF1040/GLTF1240/GLTF1570/GLTF2940 series and related GLEH/GLGH models
Frigidaire front-load washers — Additional 38712, 38802, 970L48022A0, 970L48422E0 and related legacy models
Electrolux front-load washers — select models with the matching striker configuration
Kenmore / Sears front-load washers — 4124182300/2301, 412180/181/182/183/184, 4129042992, 4129052991, 410032990, 410042990, 410052990, 4101400, 410410, 410411 and related Frigidaire-built models
Crosley front-load washers — BTF1240ES0/ES1, BTF1240FS0 and related models
Gibson front-load washers — select models
Kelvinator, Tappan, Westinghouse front-load washers — select models
Note: The door striker (131763302) and the door lock assembly (131763256) are two separate components that work together — the striker enters the lock, and the lock grips the striker. If both are worn or one has caused damage to the other, replacing them together as a matched set ensures reliable door locking and prevents premature wear on the new part. Always verify your model number before ordering.
Key Features
Washer door striker — mounts to the inside edge of the door and enters the lock mechanism when the door closes
Activates the door switch to signal the control board that the door is safely closed and ready for the wash cycle
Restores the proper engagement between the door and lock assembly for consistent locking every cycle
Current OEM production part number — supersedes many earlier revisions (131763310, 131763300, 131763340, 134456600, and more)
Gray and red plastic construction, approximately 2.6" x 1.3"
Replaces 20+ OEM and cross-reference part numbers spanning Frigidaire, Electrolux, GE (WH10X10004), and universal aftermarket catalogs
Compatible with Frigidaire Affinity series and a broad set of Frigidaire, Electrolux, Kenmore, Crosley, Gibson, Kelvinator, Tappan, and Westinghouse front-load washers
Often replaced together with the matching door lock assembly (131763256, sold separately)
Aftermarket replacement built to OEM-equivalent quality standards
Quick DIY repair — installs in under 5 minutes with a Phillips screwdriver
Product Specifications
Part Number
XP131763302
Supersedes
131763310, 131763300, 131763340, 131763330, 134456600, 134456602, 134456640
Part Type
Washer Door Striker (Door Strike / Door Catch)
Condition
Aftermarket Replacement
Application
Front-Load Washers (Frigidaire platform)
Dimensions
Approximately 2.6" x 1.3"
Color
Gray / Red
Material
Plastic
Mounting Location
Inside edge of washer door
Often Paired With
Door Lock Assembly (131763256, sold separately)
Compatible Brands
Frigidaire, Electrolux, Kenmore, Crosley, Gibson, Kelvinator, Tappan, Westinghouse
Installation Notes
⚠️ Unplug Washer Before Starting — Quick Toolless Replacement Disconnect power before beginning. Wear work gloves to protect your hands. Open the washer door — if the door is stuck locked because of a failed lock, use a putty knife to release the manual override latch through the bottom service opening. Locate the old door striker on the inside edge of the washer door. It's typically secured by a single Phillips screw. Unscrew the mounting screw and remove the old striker. If the striker has broken off inside the lock mechanism on the front panel, remove any broken pieces from the lock before proceeding — leaving debris in the lock will damage the new striker and prevent proper engagement. Take the new 131763302 striker and align it with the mounting hole in the same direction and orientation as the old one — installing it backwards will prevent the lock from engaging. Secure the new striker with the Phillips mounting screw. Close the door and confirm the striker enters the lock slot smoothly. Restore power and run a test cycle to confirm the door locks properly and the washer starts. Tools needed: Phillips screwdriver, putty knife (for stuck doors), work gloves.
Frequently Asked Questions
What's the difference between the door striker and the door lock assembly?
These are two separate parts that work together as a system to lock the washer door. The door striker (131763302) is the plastic part attached to the inside edge of the washer door — when the door closes, the striker enters the lock. The door lock assembly (131763256) is the assembly mounted on the front panel just inside the door opening — it contains the latching mechanism that grips the striker and the electrical switch that tells the control board the door is closed. If the striker is broken, the lock has nothing to grip and the washer won't start. If the lock is broken, the striker can still enter the slot but the lock won't hold it or send the right signal. Both can fail independently, and often wear together — many repairs call for replacing both at the same time.
What is the difference between 131763302 and the older 131763310 or 131763300?
All are the same door striker across production revisions. 131763300 was the original OEM part number, 131763310 and 131763340 were mid-generation revisions, and 131763302 is the current OEM production version. Frigidaire also uses 134456600, 134456602, and 134456640 as additional catalog references for the same part. All are physically and functionally interchangeable — if your washer's parts diagram shows any of these numbers, the 131763302 is the correct current replacement, and this listing covers all of them.
My washer won't start and the door seems to close normally — could this be the striker?
Yes, this is one of the most common symptoms of a failed door striker on Frigidaire-platform front-load washers. Even though the door appears to close, if the striker has cracked or worn down, it may not physically engage the lock or activate the door switch correctly. Visually inspect the striker on the inside edge of the door — if it's broken, missing, chipped, or its tab has worn down, replacement is straightforward. Also inspect the lock opening on the front panel: if there are broken plastic pieces inside from the old striker, they need to be removed before the new striker can seat properly.
Do I really only need a Phillips screwdriver for this repair?
Correct — the 131763302 striker is held in place by a single Phillips mounting screw on the inside edge of the washer door. Remove the old striker, install the new one in the same orientation, and tighten the screw. The whole replacement typically takes under 5 minutes once you have the new part in hand. Just make sure to install it in the correct direction — installing the striker backwards will prevent the lock from engaging when the door closes.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Frigidaire/Electrolux OEM part, but is manufactured from durable plastic to match the dimensions (approximately 2.6" x 1.3"), mounting configuration, and lock-engagement function of the original 131763302 door striker used in compatible Frigidaire, Electrolux, Kenmore, Crosley, and related front-load washers.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
XPARTCO WH01X10060 Washer / Dryer Selector Knob – Compatible with GE & Hotpoint Laundry Units
Product Description
Restore smooth control and reliable operation with the XPARTCO WH01X10060 Washer / Dryer Selector Knob. This high-quality aftermarket replacement knob fits securely onto the selector switch shaft, allowing easy and precise cycle or function selection. A cracked, loose, or missing selector knob can make it difficult to operate your washer or dryer correctly. Replacing it with this durable XPARTCO knob helps restore normal operation and improves everyday usability.
XPARTCO is a trusted aftermarket brand offering appliance replacement parts built to OEM-equivalent specifications at a cost-effective price.
Replaces Part Numbers
WH01X10060, WH01X10140, 277248, WE01M0445, WE01X10142, WE01X10147, WE1M445, WE1X10142, WE1X10147, WH01X10107, WH01X10135, WH1X10060, WH1X10107, WH1X10135, WH1X10140, PD00001193, EAP268450, AH268450, EA268450, AP2044504, PS268450.
Compatibility
This replacement washer / dryer selector knob fits select GE and Hotpoint washers and dryers.
Commonly used on laundry units with rotary selector switches.
Always verify your appliance’s model number before ordering.Contact our support team if you’re unsure.
✅ Key Features
🔄 Aftermarket Replacement – Matches OEM fit and appearance
🎛️ Smooth Selector Control – Restores easy cycle or function selection
🧩 Direct-Fit Design – Push-on fit for secure installation
💪 Durable Plastic Construction – Built for repeated daily use
💰 Cost-Effective Repair – Affordable alternative to OEM knobs
📐 Product Specification
Part Number: WH01X10060
Component Type: Washer / Dryer Selector Knob
Material: High-strength molded plastic
Color: White (OEM-style)
Mounting: Push-on / shaft-fit
Quality Level: Aftermarket replacement (not OEM)
🛠️ Installation Notes
Tools Needed: None
⚠️ Safety First: Ensure the washer or dryer is powered off before installing the knob.
Basic Steps:
Turn the appliance off.
Align the new XPARTCO WH01X10060 knob with the selector shaft.
Press firmly until fully seated.
Rotate to confirm smooth operation.
⏱️ Time Required: Under 2 minutes
📦 Shop With Confidence
🚚 Free Shipping on All Orders
⚙️ Trusted Aftermarket Appliance Parts
🔄 30-Day Return Policy
Restore smooth control in seconds — Add to Cart Now for a quick, budget-friendly fix!
WP389386 Washer Lower Agitator
Fits Specific Top Load Washer Models.
Replaces Part Number: WP389386, 389386, 2418, 99989683, AP6008839, PS11741980.
Description: The Lower Agitator is an OEM part designed for select Kenmore, Whirlpool top-loading washing machines. It sits at the bottom of the wash tub and plays a key agitation role during cycles. This is the bottom part of the agitator assembly.
3204405 Washer Outer Tub Bearing
Replaces: 3204405, 508644, AH446536, EA446536, AP2131587, PS446536.
3204405 Washer Outer Tub Bearing – Genuine OEM Replacement
Fix noisy or unbalanced wash cycles with the 3204405 Outer Tub Bearing. This Genuine OEM part supports the washer drum and allows smooth, quiet rotation during cycles.
Key Features:
✅ Genuine OEM Part – designed for reliable, long-lasting performance
🔁 Replaces: 3204405, 508644, AH446536, EA446536, AP2131587, PS446536.
🌀 Ensures smooth drum movement and reduces vibration
🛠️ Fits select Frigidaire, Gibson, Kenmore, Westinghouse washers
🧰 Essential for tub and spin basket support
⚠️ Washer must be disassembled for bearing replacement. Contact us to confirm compatibility.
📦 Part Number: 3204405💯 30-Day Money Back Guarantee
W10518394 Genuine OEM Whirlpool Dishwasher Heating Element
The W10518394 is a Genuine OEM Whirlpool replacement dishwasher heating element compatible with select Whirlpool, Maytag, KitchenAid, Amana, and Kenmore Whirlpool-built dishwashers — including the WDF, WDT, ADB, and related series. The heating element is mounted at the bottom of the dishwasher tub and serves two purposes: it heats the wash water to the temperature required by the selected cycle (improving cleaning performance and helping detergent dissolve and work effectively), and it provides drying heat at the end of the cycle to evaporate moisture from dishes during the heated dry phase. When the element fails, dishes come out wet, glassware is spotted or cloudy, and wash performance noticeably degrades.
This is an oval-shape element rated 1200W, approximately 15"L x 3"W x 3"H. As a Genuine OEM part manufactured by Whirlpool to factory specifications, the W10518394 directly replaces W10518394VP, W10134009, W10441445, 8194250, 8563007, 8563464, 8572861, 2977737, 1381534, 8268559, A3-06, AP4325066, AP5690151, EAP9605070, PD00012075, PS1960583, and PS9605070. The element mounts to the bottom of the tub with large nuts on the underside — the rubber washer (Whirlpool 717273) and heater nut (Whirlpool 8268548) are sold separately if they need replacement. Important: after installation on most Whirlpool dishwashers, you must run the diagnostic mode to reset the control board to recognize the new element. Installs in 30–45 minutes with basic hand tools.
Quick Answer
The W10518394 Genuine OEM Whirlpool Dishwasher Heating Element fixes Whirlpool, Maytag, KitchenAid, Amana, and Kenmore dishwashers where dishes come out wet, glassware is spotted, wash water isn't getting hot, or the heated dry phase isn't working. Oval shape, 1200W, ~15"L x 3"W x 3"H. Genuine OEM. Replaces W10518394VP, W10134009, W10441445, 8194250, 8563007, 8563464, 8572861, 2977737, AP4325066, AP5690151, PS1960583, PS9605070. Diagnostic reset required on most Whirlpool dishwashers after installation. Rubber washer (717273) and heater nut (8268548) sold separately if needed.
Common Problems This Part Fixes
Dishes coming out wet at the end of the cycle — element not providing heat for the drying phase
Wash water not getting hot enough — poor cleaning performance even with proper detergent
Glassware coming out cloudy or spotted — water not reaching temperature for proper detergent activation
Heated dry cycle not working — no warm air at the end of the cycle
Element visibly burned through, broken, or showing arcing damage
Multimeter continuity test on the element shows an open circuit (no continuity)
Heating element showing the wrong region glowing red (only a 6" segment heating rather than the whole element)
Detergent not fully dissolving — water too cool to activate the formulation
Replaces Part Numbers
This dishwasher heating element directly replaces the following OEM and cross-reference part numbers:
W10518394, 2977737, 8194250, 8563007, 8572861, W10134009, W10441445, W10518394VP, AWP40983, PD00004893, EAP8260087, AP5690151, PS8260087.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Always confirm the shape and dimensions of your old element match this oval ~15" element before ordering — some Whirlpool dishwashers use a different horseshoe-style element instead.
Compatibility
This dishwasher heating element is compatible with select Whirlpool, Maytag, KitchenAid, Amana, and Kenmore dishwashers, including:
Whirlpool dishwashers — WDF330PAHS, WDF520PADM, WDT720PADM, WDT730PAHZ series and related models
Whirlpool dishwashers — additional WDF and WDT series models (verify with parts diagram)
Maytag dishwashers — select models (verify with parts diagram)
KitchenAid dishwashers — select models
Amana dishwashers — ADB1400AGW and related models
Kenmore / Sears dishwashers — select Whirlpool-built models
Important — Confirm Element Shape Before Ordering: The W10518394 is an oval-shape heating element approximately 15" in length. Some Whirlpool-platform dishwashers use a different horseshoe-style heating element instead, which is NOT interchangeable with this one. Before ordering, visually compare your old element's shape and length to this part, or check your dishwasher's parts diagram to confirm W10518394 is the correct element for your specific model. If your element is horseshoe-shaped, you need a different part number — contact our support team with your model number.
Key Features
Genuine OEM part manufactured by Whirlpool to factory specifications — guaranteed fit and performance
Heats wash water for optimal cleaning performance and provides drying heat during the heated dry phase
Rated 1200W for efficient heating and reliable temperature control
Oval-shape element approximately 15" L x 3" W x 3" H
Mounts in the bottom of the dishwasher tub, secured underneath with large nuts
Note: rubber washer (Whirlpool 717273) and heater nut (Whirlpool 8268548) sold separately if yours need replacement
Diagnostic reset required on most Whirlpool dishwashers after installation (typically pressing any 3 buttons in sequence 3 times)
Replaces 18+ OEM and cross-reference part numbers including W10518394VP, W10134009, W10441445, 8194250, 8563007, 8563464, 8572861, AP4325066, AP5690151, PS1960583, PS9605070
Compatible with Whirlpool WDF and WDT series, Maytag, KitchenAid, Amana ADB1400AGW, and Kenmore Whirlpool-built dishwashers
DIY repair — installs in 30–45 minutes with basic hand tools
Product Specifications
Part Number
W10518394
Part Type
Dishwasher Heating Element
Condition
Genuine OEM
Application
Dishwashers (Whirlpool platform)
Shape
Oval (NOT interchangeable with horseshoe-style elements)
Wattage
1200W
Dimensions
Approximately 15" L x 3" W x 3" H
Mounting Location
Bottom of dishwasher tub
Related Parts (Sold Separately)
Rubber Washer (717273), Heater Nut (8268548)
Post-Install Step
Diagnostic reset required on most Whirlpool dishwashers
Compatible Brands
Whirlpool, Maytag, KitchenAid, Amana, Kenmore
Installation Notes
⚠️ Unplug Dishwasher and Shut Off Water Before Starting — Don't Touch Element with Bare Hands Disconnect power at the breaker and shut off the water supply at the valve under the sink before beginning. Wear work gloves and safety glasses to protect your hands and eyes. Handle the new heating element only by the metal end terminals or its support brackets — do NOT touch the heating coil itself with bare fingers; skin oils can cause hot spots that shorten element life. From inside the dishwasher tub, the element is visible at the bottom — it's the looped metal coil running along the floor of the tub. Remove the bottom rack and any debris to clear access. To access the wire connections and mounting nuts, you'll need to either reach underneath the dishwasher from the front access panel or, on some installations, pull the dishwasher out partially. From underneath: disconnect the two wires from the bottom of the element terminals (photograph the wire connections first to ensure correct reinstallation). Remove the plastic nuts holding the element terminals in place. From inside the tub, lift the old element straight up and out. Inspect the rubber washers — if they're cracked, hardened, or torn, replace them now with new 717273 washers. Install the new W10518394 element through the same mounting holes, replace the rubber washers if needed, and secure with the plastic nuts (or new 8268548 nuts) from underneath. Reconnect the two wires to the terminals matching your original orientation. Important: after restoring power, run the Whirlpool diagnostic mode to reset the control board — on most models this is done by pressing any three buttons in sequence three times and closing the door, which initiates a ~30-minute diagnostic cycle. The new element will not be recognized by the control until this is done. Tools needed: Phillips screwdriver, 5/8" wrench, 5/16" nut driver, 3/4" wrench, work gloves, safety glasses.
Frequently Asked Questions
Why are my dishes coming out wet — is the heating element the cause?
Most likely, yes — wet dishes are the classic signature of a failed dishwasher heating element. The element provides heat for the dry phase, evaporating moisture from dish surfaces. When it fails, dishes simply air-dry, which leaves them wet (especially plastics and the interior of inverted glassware). To confirm: with the dishwasher unplugged, disconnect the wires from the element and check continuity with a multimeter. A working element shows continuity; a failed element shows an open circuit (infinite resistance). Also check that you have the heated dry option enabled in your cycle settings — some users mistakenly turn off heated dry and then assume the element has failed.
After installing the new element, the dishwasher still isn't heating — why?
On most Whirlpool dishwashers, you must run the diagnostic mode after replacing the heating element so the control board recognizes the new part. To enter diagnostic mode on most Whirlpool models, press any three buttons in sequence three times rapidly, then close the door — this starts a roughly 30-minute diagnostic cycle that resets the heater logic. If you've installed the new element correctly and it still isn't heating after the diagnostic cycle, also check the high-limit thermostat (a safety component that can stop power to the element if it has failed open). Confirm your wire connections are tight on the element terminals as well.
How is the W10518394 different from horseshoe-shape heating elements?
The W10518394 is an oval-shape element about 15" in length. Some Whirlpool-platform dishwashers — even similar-looking models — use a horseshoe-shape element instead, which has a different mounting hole pattern and shape that won't fit positions designed for the oval element. The two are NOT interchangeable. Before ordering, compare your old element to a photo of the W10518394, or check your dishwasher's parts diagram. If your old element is horseshoe-shaped, contact our support team with your model number and we'll help identify the correct horseshoe-style element for your dishwasher.
Do I need to replace the rubber washers and nuts when installing this?
Not always — they're reusable as long as they're in good condition. Inspect the rubber washers (Whirlpool 717273) for cracks, hardening, or tears. If they're brittle or torn, replace them now while you have the element out — they prevent water leaks from the tub at the element mounting points. The plastic heater nuts (Whirlpool 8268548) are usually reusable unless visibly damaged. Both parts are sold separately if you need replacements. Reusing torn rubber washers is the most common cause of leaks after this repair, so don't skip the inspection.
Is this a Genuine OEM or aftermarket part?
This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It is the exact same heating element installed in compatible Whirlpool, Maytag, KitchenAid, Amana, and Kenmore Whirlpool-built dishwashers from the factory — guaranteed fit, materials, and performance.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
W11130362 Washer Genuine OEM Suspension Rod Kit
23-1/2" overall length.
The pack includes four dampers.
Fits Specific Whirlpool 4.5 CF top load washer models.
Replaces Part numbers: W11130362, W11027174, W10780040, W10594080, W10735786, W10748956, W10821710, W10901056, W11033491, W11228718, AP6262443, PS12347546.
🛠️ W11130362 Washer Genuine OEM Suspension Rod Kit
Stop the shaking. Start the cleaning. The W11130362 Suspension Rod Kit is a genuine OEM replacement designed to stabilize your washer tub and eliminate excessive vibration during spin cycles.
If your washer is banging, off-balance, or “walking” across the floor, worn suspension rods are the likely cause. This easy-to-install kit restores proper balance and extends the life of your machine.
✅ Key Features:
Genuine OEM Quality – Factory-approved replacement for W11130362
Vibration Control – Dampens movement for a smooth spin cycle
Includes All 4 Suspension Rods – Complete kit for a full fix
DIY Installation – No special tools required
Compatible with Whirlpool, Maytag, Amana, and more
🔍 Common Washer Issues This Fixes:
Excessive noise or banging during spin
Off-balance or unsteady drum
Washer “walking” or shifting position
Poor spinning or water left in clothes
💡 Why Buy from Parts-O-Matic?We carry only 100% genuine OEM parts—no substitutes. With fast shipping, verified fit, and expert customer service, Parts-O-Matic helps you fix it fast and fix it right the first time.
📦 Replaces Part Numbers:
W11130362, W11027174, W10780040, W10594080, W10735786, W10748956, W10821710, W10901056, W11033491, W11228718, AP6262443, PS12347546.
🧰 Fits Brands & Models:
Whirlpool
Maytag
Amana
Admiral
Roper
Not sure if it fits your washer model? Contact us — we’ll help you match the right part!
280146 Washer Motor Rotor
Product Condition:
Genuine OEM
New / Old Stock
Replaces Part Numbers: 280146, 1175771, 8565177, AH993018, EA993018, AP3882831, PS993018.
California Residents only
WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov
Genuine OEM WPW10446920 Dryer Push-To-Start Switch
The Genuine OEM WPW10446920 is a factory-original push-to-start switch manufactured by Whirlpool for use in Whirlpool, Maytag, Amana, Kenmore, Inglis, and other Whirlpool-built dryers that use a momentary push-button start control rather than a pull/rotary start knob. Pressing and releasing the button sends a signal to the timer or control board that begins the drying cycle; the switch itself does not stay latched, so the control electronics — not the switch — keep the dryer running after you let go.
When this switch fails, the dryer typically has power (the display and drum lights, if equipped, still work) but pressing Start does nothing, or the button feels mushy and requires several presses to register. As the genuine Whirlpool part, it ships with the exact factory-specified contacts, housing, and three-terminal wiring connector used on original production, so there's no fit or function guesswork. It directly replaces W10446920, 4446934, AP6021533, AWP51175, EAP11754857, OEM18064608, PD00038667, PS11754857. Installs in 15–30 minutes with basic hand tools.
Quick Answer
The Genuine OEM WPW10446920 Dryer Push-To-Start Switch fixes Whirlpool, Maytag, Amana, Kenmore, and Inglis dryers that won't start when the Start button is pressed, even though the dryer otherwise has power. This is the factory-original Whirlpool switch — not an aftermarket equivalent — with a 3-terminal wiring connector. Replaces W10446920, 4446934, AP6021533, AWP51175, EAP11754857, OEM18064608, PD00038667, PS11754857. Classic symptom: display and lights work, but pressing Start produces no response at all.
Common Problems This Part Fixes
Dryer won't start when the Start button is pressed
Start button feels loose, mushy, or requires multiple presses to register
Dryer has power (lights/display work) but the motor never engages
Intermittent starting — sometimes works, sometimes doesn't
Audible click from the button with no response from the dryer
Start switch visibly cracked, stuck, or not returning after being pressed
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This push-to-start switch directly replaces the following OEM and cross-reference part numbers:
WPW10446920, W10446920, 4446934, AP6021533, AWP51175, EAP11754857, OEM18064608, PD00038667, PS11754857
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This push-to-start switch is compatible with select Whirlpool-built dryers from the following brands:
Whirlpool dryers (including 7MWED1650EQ0, 7MWGD1750EQ0, 7MWGD1850EI0 and related models)
Maytag dryers (select Whirlpool-built models, including MED4005SW0, MGD4005SW0)
Amana dryers (select models, including NED4700YQ0, NGD4700YQ1)
Kenmore dryers (select Whirlpool-built models, including 11062332511, 11072332510)
Inglis, KitchenAid, Jenn-Air, Magic Chef, and Admiral dryers (select Whirlpool-built models)
Note: This switch is specific to dryers with a push-to-start button. It is not used on models with a rotary or pull-to-start knob — those use a different start switch design. Always verify your appliance model number before ordering. Contact our support team with your model number if you're unsure.
Key Features
Genuine Whirlpool OEM push-to-start switch — factory-original fit, form, and function
Resolves "won't start," "mushy button," and "intermittent start" symptoms caused by switch failure
Momentary contact design — signals the timer/control board to begin the cycle
3-terminal wiring connector matching original factory harness
Direct-fit mounting to the original control panel opening
Replaces W10446920, 4446934, AP6021533, AWP51175, EAP11754857, OEM18064608, PD00038667, PS11754857
Compatible with Whirlpool, Maytag, Amana, Kenmore, and Inglis dryers
Genuine OEM part — factory-specified materials and electrical rating
Quick DIY repair — installs in 15–30 minutes with basic hand tools
Product Specifications
Part Number
WPW10446920
OEM Part Number
WPW10446920
Part Type
Dryer Push-To-Start Switch
Condition
Genuine OEM Replacement
Switch Type
Momentary Push Button
Terminals
3-terminal wiring connector
Application
Push-To-Start Dryer Control Panels
Compatible Brands
Whirlpool, Maytag, Amana, Kenmore, Inglis
Installation Notes
⚠️ Unplug Dryer Before Starting Disconnect power before beginning. Access the control panel — on most models this means removing a few screws along the top or rear of the console, or releasing spring clips, and tilting or lifting the panel to expose the back of the start switch. Photograph the wiring before disconnecting. Unplug the 3-terminal wiring connector from the old switch — note the connector orientation. Depress the retaining tabs or remove the mounting screw(s) holding the switch in the control panel and push it out from the back. Install the new WPW10446920 switch into the same opening until it snaps or seats into place. Reconnect the wiring connector, matching your photos. Reassemble the control panel and secure it with its screws or clips. Plug the dryer back in and test by pressing Start — confirm the dryer begins its cycle. Tools needed: Phillips screwdriver, putty knife or flat-blade screwdriver (for spring clips, if applicable).
Frequently Asked Questions
My dryer has power but won't start when I press the button — is this the part?
This is the classic symptom of a failed push-to-start switch. If the display and any lights still work but pressing Start produces no response — not even a click or hum from the motor — the start switch is the most common cause. If you do hear a hum or click but the drum still doesn't turn, also check the thermal fuse and cycling thermostat, since a tripped thermal fuse can sometimes present with similar no-start symptoms.
Will this fit my dryer?
WPW10446920 and its cross-reference numbers fit a range of Whirlpool-built dryers across several brands, but only models with a push-to-start button — not a rotary or pull-to-start knob. Confirm fit using your dryer's exact model number before ordering, since the two start mechanisms are not interchangeable.
Is this a genuine Whirlpool part or an aftermarket equivalent?
This is the genuine, factory-original Whirlpool part — not an aftermarket equivalent. It ships with the same contacts, housing, and 3-terminal connector used in original production, so there's no guesswork on fit, feel, or electrical rating.
Do I need any special tools to install this?
No — just a Phillips screwdriver and, on some models, a putty knife or flat-blade screwdriver to release the control panel's spring clips. No soldering or wire splicing is required; the switch connects via its original 3-terminal plug.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine Whirlpool OEM Part ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
XPARTCO 134511600 Washer Drive Belt Replaces WH07X10009
The XPARTCO 134511600 is an aftermarket replacement washer drive belt (V-belt) compatible with a wide range of Frigidaire, Electrolux, GE, Gibson, Crosley, Kenmore, Tappan, White-Westinghouse, and Kelvinator washing machines. The drive belt connects the drive motor to the washer's drive system, transferring power to spin the basket and drive the transmission during agitation and spin cycles. When the belt wears out, stretches, frays, or snaps, the washer motor runs but the tub doesn't spin or agitate — one of the most recognizable failure patterns in appliance repair.
This is a universal-fit aftermarket belt that spans both the Frigidaire/Electrolux platform (134511600-series part numbers) and the GE platform (WH07X-series part numbers) — one physical belt covers both manufacturers' cross-referenced drive belt positions on compatible washers. V-belt profile, approximately 1/2" wide with a 31–32" circumference. It directly replaces 134511600, 134161100, 131686100, 131234000, 1156860, 145371, 3204418, F145371, F145371-000, AP3867042, AP3203734, AH1146950, EA1146950, PS1146950, PS960606, WH07X10009, WH07X10002, WH07X0113, WH7X10009, WH7X10002, WH7X113, AH960606, EA960606, and 1089279. Belt failures typically come from normal wear, stretching, fraying, or snapping due to overloading. Installs in 30–60 minutes with basic hand tools.
Quick Answer
The XPARTCO 134511600 Washer Drive Belt fixes Frigidaire, Electrolux, GE, Gibson, Crosley, Kenmore, Tappan, and White-Westinghouse washers where the motor runs but the tub won't spin or agitate, the washer makes squealing or burning-rubber smells, or the belt is visibly cracked, frayed, or snapped. V-belt, approximately 1/2" wide x 31–32" circumference. Universal-fit — spans both Frigidaire (134511600) and GE (WH07X10009) platforms. Replaces 134161100, 131686100, 131234000, 1156860, AP3867042, AP3203734, PS1146950, PS960606, WH07X10009, WH07X10002, WH7X113 and more.
Common Problems This Part Fixes
Washer motor runs but the tub won't spin — belt snapped or slipping
Washer won't agitate — belt no longer driving the transmission
Tub spins slowly or intermittently — belt worn, stretched, or glazed
Loud squealing or screeching during the spin cycle — belt slipping on the pulleys
Burning rubber smell during operation — belt slipping and overheating
Belt visibly cracked, frayed, glazed, or stretched
Belt broken completely — often found lying in the bottom of the cabinet
Clothes coming out sopping wet because the spin cycle isn't working
Washer stops mid-cycle when it should transition to spin
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This universal-fit washer drive belt directly replaces the following OEM and cross-reference part numbers across multiple brands:
134511600, 1156860, 131234000, 131686100, 134161100, 145371, 3204418, AH1146950, AP3867042, EA1146950, F145371, F145371-000, AFR14885, PD00000111, PS1146950, WH07X10009, WH07X0113, WH07X10002, WH7X10002, WH7X10009, WH7X113, AH960606, EA960606, AP3203734, PS960606.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This universal-fit drive belt is compatible with select washing machines from the following brands:
Frigidaire washers — FLEB43RGS3, FLEB8200FS0, FLGB43RGS1, FLSE72GCS8, FLSG72GCSA, FWS223RFS0, FWS777GHS0, FWS933FS0, FWX233RES4, FWX645LBS4, FWXB45RGS0, FEZ831AS2 and related models
Electrolux washers — select models on the Frigidaire platform
GE washers and washer/dryer combo units — select models (WH07X10009 cross-reference)
Crosley washers — CLCE500FW0, CLCE500FW1, CLCE500FW2, CLCG500FW0, CLCG500FW1, CLCG500FW3 and related models
Gibson washers — select models
Kelvinator washers — select models
Tappan washers — select models
White-Westinghouse washers — select models
Kenmore / Sears washers — select Frigidaire-built and GE-built models
Hotpoint and RCA washers — select GE-built models
Always verify your appliance model number before ordering. Contact our support team if you're unsure.
Key Features
Universal-fit washer drive belt (V-belt) — replaces both Frigidaire/Electrolux (134511600-series) and GE (WH07X-series) OEM drive belts in a single aftermarket part
Connects the drive motor to the washer's drive system, spinning the basket and driving the transmission
Resolves "motor runs but tub won't spin," "won't agitate," "squealing," and "burning rubber smell" symptoms
V-belt profile: approximately 1/2" wide with a 31–32" circumference
Durable rubber construction engineered to resist stretching, cracking, and glazing under load
Replaces 23+ OEM and cross-reference part numbers spanning Frigidaire, Electrolux, GE, and universal aftermarket catalogs
Compatible with Frigidaire, Electrolux, GE, Gibson, Crosley, Kenmore, Tappan, White-Westinghouse, Kelvinator, Hotpoint, and RCA washers
Aftermarket replacement built to OEM-equivalent quality standards
DIY repair — installs in 30–60 minutes with basic hand tools
Product Specifications
Part Number
134511600
Also Replaces (GE-side)
WH07X10009
Part Type
Washer Drive Belt (V-Belt) — Universal Fit
Condition
Aftermarket Replacement
Application
Washing Machines (Frigidaire and GE platforms)
Belt Profile
V-belt
Width
Approximately 1/2"
Circumference
Approximately 31–32"
Material
Rubber
Also Known As
V-Belt
Compatible Brands
Frigidaire, Electrolux, GE, Gibson, Crosley, Kenmore, Tappan, White-Westinghouse, Kelvinator, Hotpoint, RCA
Installation Notes
⚠️ Unplug Washer and Shut Off Water Before Starting — Wear Work Gloves Disconnect the washer from all utilities — unplug it from the outlet (or shut off the breaker) and turn off the hot and cold water supplies — before beginning. Wear work gloves to protect your hands from sharp sheet metal edges inside the cabinet. Pull the washer away from the wall to give yourself room to work. Access the drive belt by removing the rear access panel or tilting/laying the washer to reach the underside — the specific procedure varies by model, so consult your appliance's service diagram. Photograph the belt routing before removing anything so you can match the path with the new belt. Remove any pieces of the old broken belt from around the motor pulley and the transmission/drive pulley, and clear out accumulated lint or debris. Inspect the pulleys while you're in there — if a pulley is rough, grooved, or wobbly, the new belt will wear out prematurely and the pulley should be addressed too. Route the new 134511600 belt around the drive motor pulley and the transmission pulley, following the same path as the original. Rotate the pulleys by hand a few full turns to confirm the belt seats correctly in the pulley grooves and rides smoothly without twisting or binding. Confirm proper belt tension — the belt should be snug with a small amount of deflection, not loose enough to slip or so tight that it stresses the bearings. Reinstall the access panel, restore water and power, and run a test cycle to confirm the tub agitates and spins normally. Tools needed: Phillips screwdriver, nut driver, socket/ratchet, work gloves.
Frequently Asked Questions
My washer motor runs but the tub won't spin — is the belt the problem?
Almost certainly, yes. When you can hear the motor running (a hum or whir) but the tub stays still or barely turns, the drive belt has almost always snapped, slipped off its pulleys, or worn to the point where it can't grip. A quick check: unplug the washer, open the cabinet, and look for a belt lying loose in the bottom — a snapped belt is unmistakable. If the belt is still on the pulleys but glazed, cracked, or stretched, it's slipping rather than driving and needs replacement. Other symptoms that point to the belt: a squealing noise during spin, or a burning-rubber smell from the belt slipping and overheating against the pulleys.
Does this really fit both Frigidaire AND GE washers?
Yes — this is a genuine cross-brand part. The same V-belt design serves as a direct replacement for both the Frigidaire/Electrolux 134511600-series and the GE WH07X-series drive belts, and the two OEM catalogs are cross-referenced to each other through the 134161100 number. The belts share the same V-profile, width (approximately 1/2"), and circumference (31–32"), allowing a single aftermarket belt to function correctly in both platforms. Compatible models span Frigidaire's FLEB/FLGB/FLSE/FLSG/FWS/FWX series, GE washers and washer/dryer combos, plus Crosley, Gibson, Kelvinator, Tappan, White-Westinghouse, Kenmore, Hotpoint, and RCA models. Always verify your specific model number before ordering.
What causes a washer drive belt to fail?
The most common causes are normal wear and tear from continuous use, stretching over time (which reduces grip and causes slipping), fraying or cracking from age and repeated flexing, and snapping due to overloading the washer or improper installation. Chronic overloading is a big contributor — forcing the motor to drive an over-packed tub puts extreme stress on the belt. Belt failures can also be accelerated by a worn or seized pulley, which is why it's worth inspecting the motor and transmission pulleys whenever you replace the belt. If a pulley is rough, grooved, or wobbly, the new belt will wear out quickly against it.
How tight should the new belt be?
The belt should be snug in the pulley grooves with a small amount of deflection when you press on it — firm enough that it won't slip under load, but not so tight that it puts excess strain on the motor and transmission bearings. Most washers with a V-belt drive use a spring-loaded or adjustable motor mount to set tension automatically; if yours has an adjustment, follow your model's service specification. After installing, rotate the pulleys by hand a few full turns and confirm the belt tracks correctly in the grooves without twisting or riding up the sides.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Frigidaire, Electrolux, or GE OEM part, but is manufactured from durable rubber to match the V-belt profile, dimensions (approximately 1/2" wide x 31–32" circumference), and drive function of the original 134511600 and WH07X10009 washer drive belts used across compatible Frigidaire, Electrolux, GE, Gibson, Crosley, Kenmore, Tappan, White-Westinghouse, Kelvinator, Hotpoint, and RCA washers.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
5231JA2006F Refrigerator Water Filter
Description: This water filter is designed to remove impurities from the water and ice dispensed by your refrigerator, providing clean and fresh-tasting water. It effectively reduces contaminants such as chlorine, lead, mercury, and other particulates, ensuring safe drinking water for you and your family. You should replace this water filter if it becomes clogged or reaches the end of its usable life, typically every six months. Causes of a bad water filter can include normal usage leading to clogging, the accumulation of sediments and impurities over time, or damage to the filter casing. Failing to replace the filter regularly can also compromise its effectiveness.
Cross Reference Number: 5231JA2006G, 5231JA2006F, AP6889576, PS12724531, LT600P, LT600P/PC/PCS
