Search results for "tools"

S48D21 8" Range Surface Element Product Title Aftermarket S48D21 8" Range Surface Element - Compatible with Whirlpool, Maytag, Kenmore, Jenn-Air, Amana Electric Ranges Product Description Revive your electric range’s cooking performance with the Aftermarket S48D21 8" Range Surface Element from Parts-O-Matic. This high-quality aftermarket burner element replaces the original S48D21, delivering 2100 watts at 240V with a 4-turn coil design for efficient and even heating. Ideal for select Whirlpool, Maytag, Kenmore, Jenn-Air, Amana, and other brand electric ranges, it addresses issues like uneven heating, slow warm-up, or non-functional burners. Enjoy free shipping on all orders at Parts-O-Matic! Key Features: ✅ Broad Compatibility: Fits select Whirlpool, Maytag, Kenmore, Jenn-Air, Amana, and other electric range models. 🔥 Efficient Heating: 8" diameter, 4-turn coil delivers 2100 watts at 240V for consistent, even cooking. 💰 Cost-Effective Alternative: Aftermarket part offers OEM-equivalent performance at a lower price. 🛠️ Easy Installation: Plug-in design with Y-style bracket; requires no tools and takes 5–10 minutes to install. 🛡️ Fixes Common Issues: Resolves uneven heating, slow warm-up, or burners that fail to heat. Compatibility: Compatible with models including but not limited to: Whirlpool: RF110AXSQ0, RF262LXSB, RF365PXKW0 Maytag: MER4110AAH, MER4120AAQ Kenmore: 629.4297, 629.60003600 (pre-2004 models) Jenn-Air: JES9750AAB Amana: AER5511AAQ Replaces part numbers: TJ90SP21MA, 14215226, 1938283, 309917, 403782, 404110, 406000, 814154, ERS48D21, SE302, SP21MA, SU214, SU302, TS4D8221, TS4D8221PB, TS4D8221SR, TS4D8221WI, YSP21MA, AP4503257. Verify compatibility with your appliance brand and model number, please contact Parts-O-Matic support for assistance. Installation Notes: Tools Needed: None for standard installation; a flathead screwdriver may help for stubborn connections. Safety First: Unplug the range before installation to avoid electrical shock. Steps: Remove the old burner element by gently pulling it from the receptacle, align the Y-style bracket of the new S48D21 element, and plug it into the socket. Ensure the element sits flat in the drip pan. If the burner is not level, adjust the connection bolts to ensure they are parallel and push down gently. Installation takes 5–10 minutes. Note: A slight burning smell during first use is normal due to a protective coating; this will dissipate after 15–20 minutes. Download our installation guide or watch our YouTube tutorial for step-by-step instructions. Shop Parts-O-Matic for high-quality aftermarket appliance parts with free shipping on all orders and a 30-day return policy. Restore your range’s cooking performance today! Add to cart now for an affordable fix with free shipping on your entire order!

Read more less

XPARTCO EXP571 Dryer Door Catch The XPARTCO EXP571 is an aftermarket replacement door catch for electric and gas dryers from Whirlpool, Maytag, Kenmore, Frigidaire, Electrolux, GE, Amana, Crosley, White-Westinghouse, and LG. The door catch is the small plastic part the dryer door latches onto to stay securely shut during a cycle. Keeping the door tightly closed holds heat and airflow inside the drum, so clothes dry efficiently. Over time, regular wear, physical damage, or a door that has drifted out of alignment can cause the catch to crack, wear down, or lose its grip, and the door stops latching reliably. Made from durable plastic, this is a direct-fit replacement with a simple snap-in installation — no tools required. Because the same catch design was used across several appliance families, it carries a long cross-reference list spanning Whirlpool, Frigidaire, and GE part numbers; see the Replaces list below. Each order includes 1 door catch. Quick Answer The XPARTCO EXP571 Dryer Door Catch fixes a dryer door that won't stay closed, won't latch properly, or pops open during a cycle because the catch is cracked, worn, or damaged. Durable plastic, snap-in install with no tools, 1 catch per order. Fits Whirlpool, Maytag, Kenmore, Frigidaire, Electrolux, GE, Amana, Crosley, White-Westinghouse, and LG dryers. Classic symptom: you have to push or hold the door shut, or it swings open mid-cycle and heat escapes. Common Problems This Part Fixes Dryer door won't stay closed or pops open during a cycle Door doesn't latch with a firm, positive click Visibly cracked, broken, or worn catch Heat escaping around the door, leaving clothes damp after a full cycle Door feels loose or misaligned when closed Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This door catch directly replaces the following part numbers: WP71002106, WP3389441, 3389441, 71002106, AWP47565, PD00004499, AP6010685, PS11743869, AP6008299, PS11741434, WE1X1195, AGE1230465, AP2042209, PS266896, 131658800, AFR14189, AP2107362, PD00000626, PS418433, 5307521419, 10690002, 10690001, AFR14189, AP4450746, PD00000626, PS418433 This one catch design was sold under the part numbers of several manufacturers: Whirlpool/Maytag (WP71002106, WP3389441), Frigidaire/Electrolux (131658800, 5307521419), and GE (WE1X1195, WE1X1153, WE01X10023, and related). The AP/PS-prefixed numbers are third-party catalog cross-references for the same physical part. Compatibility This door catch is used on dryer models from the following brands: Whirlpool, Maytag, Amana, and Kenmore (Whirlpool-built) dryers Frigidaire, Electrolux, Crosley, White-Westinghouse, and Kenmore (Frigidaire-built) dryers GE dryers Select LG dryers Note: Because this catch was used across so many brands and model years, a full model-number list can't be shown here. The safest way to confirm fit is to match the number on your old catch, or on your dryer's parts diagram, against the Replaces list above rather than relying on brand alone. Contact our support team with your model number and we'll verify before you order. Key Features Aftermarket replacement dryer door catch Durable plastic construction for long-lasting use Simple snap-in installation — no tools required Holds the door securely closed to keep heat and airflow in the drum Cross-references to Whirlpool, Frigidaire, GE, and other OEM numbering 1 door catch per order Product Specifications Part Number EXP571 OEM Part Number WP71002106, 131658800, WE1X1195 Part Type Dryer Door Catch Condition Aftermarket Replacement Material Plastic Quantity 1 Door Catch Installation Snap-In, No Tools Required Application Whirlpool, Maytag, Kenmore, Frigidaire, Electrolux, GE, Amana, Crosley, White-Westinghouse & LG Dryers Installation Notes ℹ️ No Tools Required Unplug the dryer before starting as a general safety precaution. Open the dryer door and locate the worn or broken catch the door latches onto. Pull or pry the old catch free from its mounting position, then press the new catch into the same opening until it snaps firmly into place. Close the door and confirm it latches with a positive click and stays shut. If the door still won't seat or latch evenly after the swap, check the door's alignment and hinges, since a misaligned door can wear out a new catch quickly. Frequently Asked Questions My dryer door won't stay shut — is this the part I need? Very likely. A cracked, worn, or damaged door catch is a common reason a dryer door won't latch or pops open mid-cycle. Inspect the old catch for cracks or wear; if it looks damaged, replacing it should restore a firm latch. Will this fit my dryer? I have a Whirlpool, Frigidaire, or GE. This catch is cross-referenced to part numbers from all three families, plus several others. Match the number on your old catch or your dryer's parts diagram against the Replaces list above. If you're unsure, contact our support team with your model number and we'll confirm fit before you order. Do I need tools to install it? No. It's a simple snap-in design — remove the old catch and press the new one into place until it clicks. How many catches come in this order? Each order includes 1 door catch. The door still doesn't close right after replacing the catch. What else could be wrong? A door that has drifted out of alignment can keep a new catch from seating properly and wear it out fast. Check the door hinges and alignment against the cabinet opening. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

2 Pack - 12638000004021 Genuine OEM Midea Dryer Drum Roller The 12638000004021 is a genuine Midea OEM dryer drum support roller, sold under the Frigidaire/Midea manufacturing relationship for Midea-built dryers and select Frigidaire, Insignia, and Kenmore dryers using this same platform. This roller sits underneath the drum, along its rear support track, and does the physical work of holding the drum's weight while letting it turn freely as the belt drives it around. A dryer typically uses more than one of these rollers working together to keep the drum properly supported and centered. Over time, the wheel and bearing inside the roller wear down from the constant heat and rotation the dryer subjects them to, eventually developing a flat spot, seizing up, or simply wearing thin enough that the drum sits unevenly. A worn roller produces a distinctive symptom: a rumbling, squeaking, or thumping noise that rises and falls with drum rotation, often getting louder as a load tumbles. It directly replaces 5304511415, AP7990985. Quick Answer The 12638000004021 Genuine OEM Midea Dryer Drum Roller fixes Midea-built dryers (and select Frigidaire, Insignia, and Kenmore dryers on this platform) with a rumbling, squeaking, or thumping noise that rises and falls with drum rotation. Supports and centers the drum on its rear track. Replaces 5304511415, AP7990985. Common Problems This Part Fixes Rumbling or grinding noise that rises and falls with drum rotation Squeaking or squealing noise from inside the dryer during operation Thumping or knocking noise, especially with a heavier load Noise that gets louder over time as the roller wears further Drum that sits unevenly or wobbles slightly when turned by hand Visible flat spot, cracking, or wear on the roller wheel Noise that continues even with an empty drum tumbling Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer drum roller directly replaces the following OEM and cross-reference part numbers: 12638000004021, AP7990985, PS18170578, 5304511415, 4056012471, AP8049485, PS17993389. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drum roller is compatible with select Midea-built dryers, and also fits select Frigidaire, Insignia, and select Kenmore dryers built on the same Midea platform. Note: Always verify your full model number before ordering, since Midea and its partner brands use several different roller designs across their dryer lineup. Contact our support team with your model number if you're unsure. Key Features Genuine Midea OEM part — factory-specified wheel and bearing design Supports the drum along its rear track, allowing smooth rotation as the belt drives it Resolves "rumbling," "squeaking," and "thumping" noise symptoms caused by roller wear Direct drop-in replacement for the original roller and axle assembly Replaces 5304511415, AP7990985. Compatible with Midea, Frigidaire, Insignia, and select Kenmore dryers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number 12638000004021 Part Type Dryer Drum Support Roller Condition Genuine OEM Brand Midea Location Rear drum support track Function Supports and centers the drum during rotation Quantity 1 roller Compatible Brands Midea, Frigidaire, Insignia, Kenmore Installation Notes ⚠️ Unplug Dryer Before Starting Disconnect power at the outlet or shut off the circuit breaker before beginning. On a gas model, also close the gas shutoff valve before moving the cabinet. Wear work gloves — sheet metal edges inside the cabinet are sharp. Access is typically through the rear panel: remove the screws securing the panel, then release the drum belt from the idler pulley to relieve tension so the drum can be supported and moved slightly for access to the rollers underneath. Photograph the roller and axle positions before removing anything. Remove the retaining clip or fastener holding the worn roller's axle in place, then slide the old roller off. Install the new 12638000004021 roller onto the axle in the same orientation, and secure it with the retaining clip or fastener. While you're in there, check the other rollers by spinning each one by hand — if any feel stiff, gritty, or worn, replace them at the same time, since they're typically the same age and wear on a similar schedule. Re-tension the belt around the idler pulley, reassemble the rear panel, restore power, and run a short empty cycle to confirm the noise has resolved. Tools needed: Phillips screwdriver, nut driver, pliers, work gloves. Frequently Asked Questions My dryer makes a rumbling noise that gets louder over time. Is this the part I need? Yes, this is the classic symptom of a worn drum roller. As the wheel and bearing wear down, the noise typically starts subtle and gradually worsens, often becoming most noticeable with a full load as the extra weight puts more load on the worn wheel. If the noise rises and falls in rhythm with the drum turning, a roller is the most likely cause. Should I replace just one roller, or all of them? It's worth checking all of them while you have access. Dryers typically use more than one roller supporting the drum, and since they're the same age and under the same stress, if one has worn out the others are often not far behind. Spin each roller by hand — if any feel stiff, gritty, or rough, replace them together to avoid repeating this repair again soon. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Midea to factory specifications — guaranteed fit, materials, and performance. It matches the original wheel design, bearing, and axle fitment of the drum roller originally installed in your dryer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

341241 Dryer Genuine OEM Drum Belt The 341241 is a Genuine OEM dryer drum belt compatible with a wide range of Whirlpool-family dryers including Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Admiral, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, Norge, Modern Maid, Hardwick, Caloric, and Ikea. The drum belt wraps around the outside of the dryer drum, loops around the motor pulley and idler pulley, and drives the drum to rotate during every drying cycle. Without a functioning belt, the drum cannot spin and clothes will not tumble or dry. Made from high-strength rubber with reinforced ribs, this belt measures 92-1/4 inches long x 1/4 inch wide and features 4 ribs and 3 grooves. It is flat on one side and ribbed on the other, and is built to resist cracking, stretching, and wear under the high heat and repeated tension cycles of daily dryer use. It also replaces some 5-rib, 4-groove belts. Installs in 30–45 minutes with basic hand tools. Quick Answer The 341241 Dryer Genuine OEM Drum Belt fixes dryers where the drum is not spinning, clothes are not tumbling, or a thumping/squealing noise is coming from the dryer. Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Admiral, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, and more. Measures 92-1/4" L x 1/4" W with 4 ribs and 3 grooves. Common Problems This Part Fixes Dryer drum not spinning — motor runs but drum stays still Clothes not tumbling during the drying cycle Thumping, squealing, or slapping noise during operation Dryer runs but produces no heat because drum is stationary Burning rubber smell coming from the dryer Visible broken or frayed belt pieces found inside the dryer cabinet Clothes taking too long to dry due to drum not rotating at correct speed Replaces Part Numbers This drum belt directly replaces the following OEM and cross-reference part numbers: 341241, 14210003, 2008, 26000341241, 26000349533, 31001026, 31531589, 3389628, 3392665, 3394651, 3399844, 341241VP, 345473, 349533, 529597, 53-0186, 53-1080, 53-1086, 53-1528, 53-1589, 53-2671, 53-2910, 660996, 660997, 661561, 693306, 694088, 694416, 694868, 695055, 697388, 8066065, 8206, 8210, 920H4, 920H5, 99906951, 99989673, 99989674, FSP341241, LB276, LB279, P46-037, P46-149, W10127457, W10131364, AH346995, AP32, EA346995, ER341241, AWP39161, PD00002263, EAP346995, AP2946843, PS346995, TJ341241. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drum belt is compatible with select dryers from the following brands: Whirlpool dryers (gas and electric) Kenmore / Sears dryers (select models) Maytag dryers KitchenAid dryers Amana dryers Roper dryers Admiral dryers Jenn-Air dryers Estate dryers Magic Chef dryers Crosley dryers Inglis dryers Norge, Modern Maid, Hardwick, Caloric, and Ikea dryers Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Drives the dryer drum via the motor pulley and idler pulley for smooth, consistent tumbling every cycle 92-1/4" length x 1/4" width — 4-rib, 3-groove design; flat on one side, ribbed on the other Also replaces some 5-rib, 4-groove belts — wide cross-compatibility across Whirlpool-family models Made from high-strength rubber with reinforced ribs — resists cracking, stretching, and heat damage Direct replacement for OEM part numbers 341241 and 8066065 — no modification required Compatible with over a dozen major appliance brands built on the Whirlpool platform Genuine OEM part — factory-exact fit, materials, and dimensions DIY-friendly repair — installs in 30–45 minutes with basic hand tools Often replaced together with the idler pulley (691366) and drum rollers (349241T) for a complete drum drive repair Product Specifications Part Number 341241 Part Type Dryer Drum Drive Belt Condition Genuine OEM Application Gas and Electric Dryers Length 92-1/4 inches Width 1/4 inch Ribs 4 ribs, 3 grooves Profile Flat on one side, ribbed on the other Material High-strength rubber with reinforced ribs Color Black Compatible Brands Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Admiral, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, Norge, Modern Maid, Hardwick, Caloric, Ikea Often Replaced With 691366 Idler Pulley, 349241T Drum Rollers Installation Notes ⚠️ Safety First — Unplug Dryer Before Starting Unplug the dryer from the power source (and shut off the gas supply for gas dryers) before beginning any repair. Remove the lint screen, then unscrew the two Phillips screws inside the lint filter housing. Use a putty knife 2 inches from each front corner to release the top panel clips and lift the top panel. Remove the front panel to access the drum. Release belt tension at the idler pulley, lift the drum slightly, and slide the old belt off. Loop the new 341241 belt around the drum with the ribbed side facing down (toward the drum). Route the belt around the idler pulley and motor pulley — consult your model's service manual or a model-specific video for the correct belt path. Reassemble and run a test cycle. Tip: While the drum is out, inspect and replace the idler pulley (691366) and drum rollers (349241T) if worn. Tools needed: Phillips screwdriver, putty knife or flat pry tool. Frequently Asked Questions How does the 341241 differ from the W10205415 and 6602-001655 belts? All three are 92-inch dryer drum belts, but they differ in width and rib count. The 341241 is 1/4" wide with 4 ribs and 3 grooves. The W10205415 is 3/8" wide with 5 ribs and 4 grooves. The 6602-001655 is 5/16" wide with 5 ribs and 4 grooves designed for Samsung dryers. Always match the part number to your specific model — do not substitute based on appearance alone. Will this belt fit my Kenmore dryer? Many Kenmore dryers — especially the popular 110-series — are manufactured by Whirlpool and use the 341241 belt. Check your model number against the compatibility list and contact our support team if you need help confirming the fit before ordering. How do I know if my drum belt needs to be replaced? The most obvious sign is that the dryer motor hums but the drum does not spin. You may also notice a thumping or slapping sound during operation, a burning rubber smell, or clothes that are damp after a full cycle. Open the dryer cabinet to visually confirm if the belt is broken, frayed, or stretched. Should I also replace the idler pulley and drum rollers? Yes — since the dryer is already disassembled, it is highly recommended to inspect and replace the idler pulley (691366) and drum support rollers (349241T) at the same time. These parts wear at a similar rate and replacing all three together — often sold as a repair kit — prevents having to disassemble the dryer again in the near future. Is this an OEM or aftermarket part? This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It is the exact same belt that came installed in your dryer from the factory — same materials, dimensions, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

Y54414 Dryer Idler Pulley Replaces WPY54414 The Y54414 is a genuine Whirlpool OEM idler pulley wheel and bearing assembly for Whirlpool dryers, and also fits select Maytag, Amana, Caloric, Crosley, Kenmore, and Speed Queen models. This pulley puts tension on the drive belt as it rides against it, and correct tension is what allows the belt to grip properly and spin the drum smoothly throughout the drying cycle. Available in beige or black, this pulley wheel is 2" wide with a metallic bearing at its center, and mounts beneath the drum using two 5/16" screws. Over time, the bearing wears out or the wheel becomes damaged, and once that happens, the pulley can no longer maintain proper belt tension. Symptoms of a failing idler pulley include the dryer making noise during operation, failing to start, or failing to tumble, even though other parts of the drying cycle — like heating — may continue working normally. It directly replaces WPY54414, WPY54414VP, 14218926, 54414, 54414-REPL, 54414-2, R0609504, R0609504-REPL, AP6024203, AP6329060, PS11757553, EAP11757553, PS17001032, D510142P, 510142P, and 510142. Quick Answer The Y54414 Dryer Idler Pulley fixes Whirlpool, Maytag, Amana, Caloric, Crosley, Kenmore, and Speed Queen dryers making noise during operation, failing to start, or failing to tumble — even while other functions like heating still work. 2" pulley wheel with metallic bearing, beige or black. Replaces WPY54414, WPY54414VP, 14218926, 54414, 54414-REPL, 54414-2, R0609504, R0609504-REPL, AP6024203, AP6329060, PS11757553, EAP11757553, PS17001032, D510142P, 510142P, 510142. This pulley is located beneath the drum — removing the blower housing and motor first makes access considerably easier. Common Problems This Part Fixes Dryer making noise during operation Dryer fails to start Dryer fails to tumble Dryer dries clothes but makes a terrible or unusual noise while doing so Belt slipping or losing tension Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer idler pulley directly replaces the following OEM and cross-reference part numbers: WPY54414, Y54414, 14218926, 54414, R0609504, WPY54414VP, 54414-REPL, R0609504-REPL, AP6024203, AWP51465, EAP11757553, PD00002420, PS11757553, D510142P, 510142P, 510142, D510142, 510142P, 510142, 54414, 54415, 54415P, AP6329060, ASQ376005, PD00042476, PS17001032, DE407 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This idler pulley is compatible with select Whirlpool dryers, and also fits select Maytag, Amana, Caloric, Crosley, Kenmore, and Speed Queen dryers built on the Whirlpool platform, including model numbers such as SDG3606AWW, LG8469W2, SDE3606AYW, SDE4606AYW, SDG4606AWW, and LEA30AW. Note: This is a different idler pulley from our 279640 listing, used on other Whirlpool/Kenmore dryer models. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which pulley your dryer needs. Key Features Genuine Whirlpool OEM part — factory-specified pulley wheel and bearing design Maintains proper tension on the drive belt for smooth drum rotation Resolves "noisy operation," "won't start," and "won't tumble" symptoms caused by pulley failure 2" wide pulley wheel with metallic bearing Available in beige or black Mounts beneath the drum with two 5/16" screws Direct drop-in replacement matching the original mounting Replaces WPY54414, WPY54414VP, 14218926, 54414, 54414-REPL, 54414-2, R0609504, R0609504-REPL, AP6024203, AP6329060, PS11757553, EAP11757553, PS17001032, D510142P, 510142P, and 510142 Compatible with Whirlpool, Maytag, Amana, Caloric, Crosley, Kenmore, and Speed Queen dryers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number Y54414 OEM Part Number WPY54414 Part Type Dryer Idler Pulley Wheel & Bearing Assembly Condition Genuine OEM Color Beige or Black Wheel Width 2" Bearing Metallic, center-mounted Location Beneath the drum Mounting Two 5/16" screws Repair Difficulty Moderate — drum removal required for access Quantity 1 idler pulley Compatible Brands Whirlpool, Maytag, Amana, Caloric, Crosley, Kenmore, Speed Queen Installation Notes ⚠️ Unplug Dryer Before Starting — Remove The Blower Housing And Motor First For Easier Access Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. This pulley is located beneath the drum, so the drum will need to be removed to access it. Per official guidance, it's also recommended to remove the blower housing and motor from the dryer for easier access to the idler pulley. With the drum out and access clear, locate the idler pulley and remove the two 5/16" screws securing it in place. Take out the old pulley. Install the new Y54414 in the same position, making sure it's seated correctly against where the belt will ride, and secure it with the two 5/16" screws. Reinstall the motor and blower housing if removed, then reinstall the drum. Reroute the drive belt around the drum, motor pulley, and this idler pulley, matching the original path. Reassemble any panels removed for access. Restore power and run a test cycle to confirm quiet, smooth tumbling with proper belt tension. Tools needed: 5/16" nut driver or socket, Phillips screwdriver, work gloves. Frequently Asked Questions My dryer dries clothes fine but makes a terrible noise. Is this the part I need? Yes, this is a documented symptom of a worn idler pulley. One customer described exactly this: "The dryer would dry clothes but made a terrible noise" — after watching a repair video to identify the correct part, they confirmed this idler pulley was the cause, since a worn or damaged pulley can still allow the dryer to function while producing noticeable noise as it rubs or wobbles against the belt. Is there an easier way to access this pulley than pulling out the whole drum? The drum does need to come out since this pulley sits beneath it, but official guidance recommends also removing the blower housing and motor from the dryer, which makes reaching and working with the idler pulley considerably easier than trying to access it with those components still in place. My dryer won't start at all. Could this pulley really be the cause? Yes, on some models. If the idler pulley fails to put proper tension on the belt, some dryers won't allow the cycle to start at all rather than simply running without tumbling, since certain safety interlocks depend on normal belt tension and drum movement. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original pulley wheel size, bearing type, and mounting configuration of the idler pulley originally installed in your dryer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WB03X43926 Genuine OEM GE Range Surface Burner Control Knob Set The WB03X43926 is a genuine GE OEM surface burner knob kit, including 5 stainless steel knobs for GE, Hotpoint, Haier, Monogram, and Café ranges. These are the knobs you turn to light and adjust each surface burner — each one fits onto a control shaft behind the panel, and its position controls the heat setting for that burner. Since this kit includes a full set of five, it's designed for replacing every burner knob on the range at once rather than mismatching a single new knob against several older, worn ones. Over years of use, the finish on plastic-coated or stainless-finished knobs can crack, peel, or start to bubble, and the knobs themselves can become loose or worn at the point where they grip the control shaft. A full-set replacement gives your range a uniform, refreshed look while also resolving any individual knobs that have become difficult to turn or read. Weighing approximately 2.64 oz total, this kit requires no tools to install — each knob simply pulls straight off its post and the new one presses straight back on. It directly replaces AP7187858, WB03K10305, WB03K10303, WB03K10208, WB03K10221, and WB03K10294. Quick Answer The WB03X43926 Genuine OEM GE Range Surface Burner Control Knob Set fixes GE, Hotpoint, Haier, Monogram, and Café ranges with burner knobs that are cracked, peeling, bubbling, loose, or simply worn-looking after years of use. Set of 5 stainless steel knobs. Replaces AP7187858, WB03K10305, WB03K10303, WB03K10208, WB03K10221, WB03K10294. No tools required — each knob pulls straight off and the new one presses straight on. Common Problems This Part Fixes Burner knobs with cracked, peeling, or bubbling finish Knobs that feel loose or wobbly on the control shaft Knobs that are hard to read due to worn or faded markings Mismatched or inconsistent-looking knobs across the range from replacing them one at a time Knobs that have become difficult to turn smoothly General wear after many years of daily cooking use Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This range surface burner knob set directly replaces the following OEM and cross-reference part numbers: WB03X43926, WB03K10303, WB03K10305, WB03K10208, WB03K10221, WB03K10294, AP7187858, OEM21563583, AGE21567, PD00074146 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This burner knob set is compatible with select GE ranges, and also fits select Hotpoint, Haier, Monogram, and Café ranges built on the GE platform. Note: This is the stainless steel finish knob set. GE also sells a visually different black plastic knob (WB03T10236) for other range models — the two are not interchangeable, so confirm your original knob's finish and shaft style before ordering. Always verify your full model number before ordering, since GE uses several different knob designs across its range lineup. Contact our support team with your model number if you're unsure which knob set fits your range. Key Features Genuine GE OEM part — factory-specified fit and finish Complete set of 5 stainless steel surface burner knobs for a uniform look across the range Resolves "cracked or peeling finish," "loose knob," and "worn markings" symptoms No tools required — pulls straight off the post, presses straight back on Compatible with the same control shaft used across a range of GE-platform ranges Replaces AP7187858, WB03K10305, WB03K10303, WB03K10208, WB03K10221, and WB03K10294 Compatible with GE, Hotpoint, Haier, Monogram, and Café ranges Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number WB03X43926 Part Type Range Surface Burner Control Knob Set Condition Genuine OEM Brand GE Kit Contents 5 surface burner knobs Finish Stainless steel Weight Approx. 2.64 oz. (full set) Mount Style Push-fit onto control shaft Repair Difficulty Very Easy — no tools required Quantity 1 set (5 knobs) Compatible Brands GE, Hotpoint, Haier, Monogram, Café Installation Notes ⚠️ Unplug Range Or Shut Off Breaker Before Starting Disconnect power at the outlet or shut off the circuit breaker before beginning. Remove each old knob by pulling it straight off its post — on most models this requires no tools, just firm, even pressure. Align each new knob from the WB03X43926 set with its corresponding control panel position and indicator arrow, then press it firmly onto the post until it seats flush. Repeat for all five burner positions. There's no need to remove the knobs for normal baking, broiling, or self-clean use once installed. Restore power and test that each knob turns smoothly through its full range, with the markings lining up correctly against the indicator arrow at each setting. Tools needed: none. Frequently Asked Questions My knobs' finish is bubbling after many years. Is this the right fix? Yes, this is a common wear pattern on older knobs — one customer described replacing 14-year-old knobs whose coating had started to bubble, and found the swap simple enough to do entirely by hand with no tools. If your knobs are showing this kind of surface wear, a full set replacement gives your range a consistent, refreshed look across all burners. Do I need to remove these knobs before running a self-clean cycle? No — these knobs are designed to be left in place during normal oven use, including self-clean cycles. One customer specifically noted using the self-clean feature without removing the knobs and had no issues. Can I buy just one replacement knob instead of the full set of 5? This particular listing is sold as a complete 5-knob set rather than individually. If only one knob has failed, you may still prefer the full set for a matching, uniform appearance across the range, especially if the remaining original knobs are also showing age. Contact our support team if you're looking for a single replacement knob instead. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by GE to factory specifications — guaranteed fit, materials, and performance. It matches the original stainless steel finish, shaft fit, and marking layout of the surface burner knobs originally installed on your range. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

12638200000241 Genuine OEM Midea Dryer Drum Belt The 12638200000241 is a Genuine OEM Midea replacement dryer drum belt compatible with a wide range of Midea, Criterion, and Insignia electric and gas dryers, including the MLE41/45/47/52, MLG45/52, MLTE37, CDE41, CDG41/45, CLADE67, and MDD160 series. The drum belt wraps around the dryer drum and the motor pulley, transferring the motor's rotation to spin the drum during the drying cycle. When the belt breaks, stretches, or wears out, the motor continues to run but the drum no longer spins — clothes sit still in the drum while the motor hums, and the dryer cannot complete a normal cycle. As a Genuine OEM part manufactured by Midea to factory specifications, the 12638200000241 is constructed from durable black rubber. Packaged dimensions are approximately 11" L x 3" W x 2" H. Note: if the drum belt has failed, this is also a good opportunity to inspect the drum support rollers (Midea 12638000004021) and the idler/tensioner pulley assembly while the dryer cabinet is open — these components wear together and a failing roller or pulley can accelerate belt wear. Installs in 45–60 minutes with basic hand tools. Quick Answer The 12638200000241 Genuine OEM Midea Dryer Drum Belt fixes Midea, Criterion, and Insignia dryers where the motor runs but the drum doesn't spin, the belt has snapped or is visibly stretched, or where there's a burning rubber smell during operation. Black rubber drum belt. Packaged dimensions approximately 11" L x 3" W x 2" H. Genuine OEM. Compatible with Midea MLE41/45/47/52, MLG45/52, MLTE37, CDE41, CDG41/45, CLADE67, MDD160 series, plus Criterion CDE41N1AW/CDG41N1AW/CDG45N1AW and Insignia Midea-built models. Common Problems This Part Fixes Drum not spinning — belt has broken or slipped off Motor runs and hums but the drum stays still Drum spins intermittently — belt slipping under load Burning rubber smell during operation — belt slipping on the motor pulley Squealing or chirping noise during the drying cycle — belt frayed or stretched Belt visibly cracked, frayed, broken, or missing inside the dryer cabinet Extended drying times — drum not rotating at correct speed due to a worn belt Replaces Part Numbers This drum belt directly replaces the following part number: 12638200000241, AP7158561, PS18170626 This is the Midea manufacturer part number used across the compatible Midea, Criterion, and Insignia dryer platform. Contact our support team with your model number if you need confirmation before ordering. Compatibility This drum belt is compatible with select Midea, Criterion, and Insignia electric and gas dryers, including: Midea electric dryers — MLE41N1AWW, MLE45N1AWW, MLE45N1BWW, MLE45N3BMG, MLE45N3BWW, MLE47A3AGG, MLE47C3AWW, MLE47C4AWW, MLE47R5BWW, MLE52N3AWW, MLE52S7AGS, MLE52S7AWW Midea gas dryers — MLG45N1AWW, MLG45N1BWW, MLG45N3BMG, MLG45N3BWW, MLG52S7AGS, MLG52S7AWW Midea — MLTE37N1BWW, CLADE67W, MDD160A2301E1305 and related models Criterion — CDE41N1AW (electric), CDG41N1AW (gas), CDG45N1AW (gas) Insignia electric dryers — NSDRE67WH8A, NSFDRE67WH8A, NSFDRE67WH8AC, NSFDRE77WH8B, NSTDRE67W1, NSTDRE75W1 Insignia gas dryers — NSFDRG67WH8A, NSTDRG67W1, NSTDRG75W1 Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Genuine OEM part manufactured by Midea to factory specifications — guaranteed fit and performance Wraps around the dryer drum and motor pulley to transfer the motor's rotation to spin the drum Durable black rubber construction designed for continuous flex and motor load Packaged dimensions: approximately 11" L x 3" W x 2" H Compatible with the full Midea, Criterion, and Insignia electric and gas dryer platform Often replaced along with the drum support rollers (Midea 12638000004021) and idler pulley assembly Installs in 45–60 minutes with basic hand tools Product Specifications Part Number 12638200000241 Part Type Dryer Drum Belt Condition Genuine OEM Application Electric and Gas Dryers (Midea platform) Material Rubber Color Black Packaged Dimensions Approximately 11" L x 3" W x 2" H Often Replaced With Drum Support Roller (Midea 12638000004021) Compatible Brands Midea, Criterion, Insignia Installation Notes ⚠️ Unplug Dryer Before Starting (Shut Off Gas First on Gas Models) — Wear Work Gloves Disconnect power before beginning (and shut off the gas supply first if you have a gas dryer model). Wear work gloves — there are sharp sheet metal edges inside the dryer cabinet. Remove the lint filter housing screws, release the top panel locking clips with a putty knife, and lift the top panel. Disconnect the door switch harness and remove the front panel to access the drum, drive belt, and motor/idler pulley assembly. Take a photo of the existing belt routing before removing anything — this is essential for correct reassembly. Release the old belt from the idler pulley and slide it off the drum and motor pulley. Carefully lift the drum out and inspect the drum support rollers and idler pulley for wear — replace them now if needed while the dryer is open. Wrap the new 12638200000241 belt around the drum (ribbed side against the drum). Reinstall the drum, then route the belt around the motor pulley and under the idler pulley, allowing the idler to tension the belt. Reassemble the front panel and top panel in reverse order. Restore power (and gas, for gas models) and run a test cycle to confirm smooth, quiet drum rotation. Tools needed: Phillips screwdriver, putty knife, work gloves. Frequently Asked Questions How do I know if the drum belt has failed? The clearest sign of a broken drum belt is a dryer where the motor starts and runs normally, but the drum does not spin — you'll hear the motor humming with no drum movement. If you open the door mid-cycle and the drum spins freely with no resistance (as if disconnected from the motor), the belt has either broken or slipped off completely. A stretched or worn belt that still drives the drum may also produce squealing or burning rubber smells from slippage on the motor pulley. Visually inspecting the belt after removing the dryer's front panel confirms the condition. Should I replace the drum rollers and idler pulley at the same time? Yes — since the dryer cabinet must already be opened and the drum removed to replace the belt, this is the ideal time to also inspect and replace the drum support rollers (Midea 12638000004021) and the idler/tensioner pulley. All three components form the drum drive system and tend to wear together. A worn roller or pulley is often what caused the belt to fail prematurely in the first place. Addressing them together in a single repair eliminates the most common drum drive failure points and prevents a near-term repeat teardown. Does this belt fit Insignia and Criterion dryers as well as Midea? Yes — Insignia (Best Buy) and Criterion (Sears/Kmart) are house brands whose dryers in this size class are manufactured by Midea and use the same internal components, including this drum belt. Confirmed compatible models include Insignia NSDRE67WH8A, NSFDRE67WH8A, NSFDRE77WH8B, NSTDRE67W1, NSTDRE75W1 (electric) and NSFDRG67WH8A, NSTDRG67W1, NSTDRG75W1 (gas), plus Criterion CDE41N1AW (electric) and CDG41N1AW/CDG45N1AW (gas). Always verify your specific model number before ordering. Which way does the belt go around the drum — ribbed side in or out? On the drum belt, the ribbed (grooved) side should face inward, against the drum surface, while the smooth side faces outward. The ribs grip the smooth drum surface to drive it as the motor pulley turns. On the motor pulley side, the belt seats in the grooves of the small motor pulley. Take a photo of how the original belt was routed before removing it — this is the most reliable way to confirm correct orientation during reinstallation. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Midea to factory specifications. It is the exact same drum belt installed in compatible Midea, Criterion, and Insignia electric and gas dryers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

279570 Genuine OEM Whirlpool Dryer Door Catch Kit The 279570 is a Genuine OEM Whirlpool dryer door catch and strike kit compatible with a wide range of Whirlpool, Kenmore, Roper, Estate, Amana, Crosley, Inglis, KitchenAid, Maytag, and Admiral dryers. The door catch is the spring-clip mechanism on the dryer door that snaps over the door strike to hold the door firmly closed during operation, activating the door switch so the dryer can run. When the catch breaks, wears out, or loses tension, the door will not stay closed, the door switch will not be activated, and the dryer will either not start or will stop mid-cycle. The strike is the corresponding post or tab on the dryer cabinet that the catch engages. This Genuine OEM kit includes three color-coded door catches of different tensions and two metal door strikes, plus one screw. Because the tension of the catch must match the original, Whirlpool includes three options in the kit — each is color-coded and numbered on the back. Refer to identify which catch is correct for your model. The kit directly replaces a very large list of older cross-reference numbers including 279570VP, 3493, 2003, 8208, 279280, 279337, 696144, 693717, AP3094183, PS334230, and dozens more. Installs in under 15 minutes with a Phillips screwdriver. Quick Answer The 279570 Genuine OEM Whirlpool Dryer Door Catch Kit fixes dryers where the door won't stay closed, pops open mid-cycle, or won't activate the door switch to start. Kit includes 3 color-coded catches (different tensions), 2 metal strikes, 1 screw. Use the catch that matches your original. Genuine OEM. Compatible with Whirlpool, Kenmore, Roper, Estate, Amana, Crosley, Inglis, KitchenAid, Maytag, and Admiral dryers. Installs in under 15 minutes. Common Problems This Kit Fixes Dryer door will not stay closed during the drying cycle Door pops open mid-cycle, stopping the dryer Dryer will not start — door switch not being activated by a worn or broken catch Door feels loose or does not click shut firmly when closed Door catch visibly cracked, broken, or missing Door strike bent or missing — door cannot engage the catch properly Dryer requires the door to be held or pushed closed to stay running Replaces Part Numbers This door catch kit directly replaces the following OEM and cross-reference part numbers: 279570, 14205029, 14205577, 14210022, 2003, 236876, 236877, 241282, 241890, 26000279570, 261847, 263067, 279280, 279337, 279469, 279570VP, 291949, 3390239, 3392538, 3398175, 342295, 347813, 3493, 4165234, 51651001, 51655001, 66021, 690081, 690082, 693717, 694343, 696144, 8208, 830751, 834767, 834813, 834943, 834944, AH334230, DE902, EA334230, EAP334230, FSP279570, AP3094183, AWP39897, PD00002346, PS334230. Contact our support team with your model number if you need confirmation before ordering. Compatibility This door catch kit is compatible with select dryers from the following brands: Whirlpool dryers (gas and electric) Kenmore / Sears dryers (Whirlpool-built models) Roper dryers Estate dryers Amana dryers Crosley dryers Inglis dryers KitchenAid dryers Maytag dryers Admiral dryers Important: This kit includes three catches with different spring tensions, color-coded and numbered on the back. You must use the catch that matches the tension of your original. Using the wrong tension catch may result in a door that is too hard to open or too easy to pop open. Key Features Genuine OEM kit manufactured by Whirlpool to factory specifications — guaranteed fit and performance Holds the dryer door closed and activates the door switch so the dryer can run safely Kit includes 3 color-coded door catches (different spring tensions), 2 metal door strikes, 1 screw Catches are color-coded and numbered on the back — use the one that matches your original. Plastic catches with metal strikes and metal screw — durable construction for long service life Consolidates a very large list of older Whirlpool-family door catch cross-reference numbers Compatible with 10 major appliance brands on the Whirlpool platform Quick DIY repair — installs in under 15 minutes with a Phillips screwdriver Product Specifications Part Number 279570 Part Type Dryer Door Catch and Strike Kit Condition Genuine OEM Application Gas and Electric Dryers Kit Includes 3 color-coded door catches (different tensions), 2 metal strikes, 1 screw Material Plastic catches / Metal strikes Color White / Silver Catch Selection Color-coded and numbered, Use the catch that matches your original Compatible Brands Whirlpool, Kenmore, Roper, Estate, Amana, Crosley, Inglis, KitchenAid, Maytag, Admiral Installation Notes ⚠️ Unplug Dryer Before Starting Disconnect power before beginning. using the wrong tension catch will result in incorrect door resistance. Open the dryer door and locate the old door catch on the inside of the door panel and the strike on the dryer cabinet opening. To remove the old catch: press the retaining tabs and pull the catch free from its slot, or unscrew the mounting screw. Install the correct new catch into the same position. To replace the strike: remove the old strike (typically held by a single screw) and install the new strike in the same position. Close the dryer door to confirm it latches firmly with a satisfying click. Restore power and run a short test cycle to confirm the door stays closed and the dryer operates normally. Tools needed: Phillips screwdriver; needle-nose pliers may help with catch removal on some models. Frequently Asked Questions Why does the kit include three different catches? Whirlpool used door catches with different spring tensions across its dryer lineup — a lighter catch on some models and a stiffer catch on others. To cover all compatible models in a single kit, Whirlpool includes three catches of different tensions, each color-coded and numbered on the back. It is important to use the correct one — using a catch with too little tension may allow the door to pop open, while a catch with too much tension may make the door difficult to open. Do I need to replace both the catch and the strike, or just one? It depends on which component has failed. The catch (the spring-clip on the door) is the more commonly replaced part — it wears out from repeated use faster than the strike. Inspect both: if the catch is cracked or has lost its spring tension, replace the catch. If the strike is bent, cracked, or missing, replace the strike. Since the kit includes both catches and strikes, you have everything needed for a complete repair. When in doubt, replacing both ensures the full latch system is renewed. My dryer will not start even after replacing the door catch — what else could it be? If the dryer still will not start after the catch is replaced, the door switch may also need to be tested. The door switch is the electrical component that the door catch activates when the door closes — if the switch itself is failed, replacing the catch alone will not restore function. Test the door switch (3406107 for most Whirlpool-family models) with a multimeter for continuity in both the open and closed positions. If the switch reads open in both positions or closed in both positions, it has failed and needs replacement. How is the 279570 different from the W11429587 dryer door catch? The 279570 is the door catch kit for older Whirlpool-family dryers — it includes multiple catches of different tensions and metal strikes because it covers a wide range of older models. The W11429587 is a single snap-in door catch for newer Whirlpool-family dryers (Cabrio and newer platform models). If your dryer is a newer model with a snap-in catch slot rather than a screw-mounted catch and strike, you likely need the W11429587. Verify your model number to confirm which part is correct. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM kit manufactured by Whirlpool to factory specifications. It is the exact same door catch and strike kit supplied by Whirlpool for compatible dryer service repairs — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

Genuine OEM WP3387134 Dryer Cycling Thermostat The Genuine OEM Whirlpool WP3387134 is a dryer cycling thermostat, the operating thermostat that controls drying temperature. It switches the heating element off when the dryer reaches its set temperature and back on after it cools, keeping the inside of the dryer at a steady temperature throughout the cycle. This one is rated L155-25: it cuts out at approximately 155°F and cycles back on once the temperature drops about 25°F. When a cycling thermostat fails, the dryer may stop heating, run too hot, or keep heating after the drum has stopped. This is the original Whirlpool part, and it fits a wide range of Whirlpool-built dryers sold under the Whirlpool, Kenmore, Maytag, KitchenAid, Roper, Crosley, Estate, Amana, and other brand names. Quick Answer The Genuine OEM WP3387134 Cycling Thermostat fixes a Whirlpool-built dryer that isn't heating, runs too hot, or has inconsistent drying temperatures. Rated L155-25, it cycles the heating element off at about 155°F and back on after a 25°F drop. Classic symptom: clothes come out damp or the dryer runs excessively hot, with no sign of a clogged vent. Common Problems This Part Fixes Dryer not heating Dryer running too hot Inconsistent drying temperatures Heat staying on after the drum has stopped Dryer won't start or the timer doesn't advance, if the thermostat has failed Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This cycling thermostat directly replaces the following part numbers: WP3387134, 3387134, 2011, 2893, 3-6910, 306910, 3387135, 3387139, ET187,  EAP11741405, WP3387134VP, AP6008270, AWP47432, EAP11741405, PD00002313, PS11741405, L155-25F These numbers span several generations of Whirlpool's own part numbering for this thermostat as model lines were updated. All are the correct replacement regardless of which number appears on your dryer's parts diagram. Compatibility This thermostat fits a wide range of Whirlpool, Kenmore, Maytag, KitchenAid, Roper, Crosley, Estate, Amana and related dryers, including these examples: Kenmore 11060012000, 11060012001, 11060022010, 11060172000, 11060232000, 11060602990 Numerous additional Whirlpool-built dryer models Note: This is the cycling (operating) thermostat, not the high limit thermostat or the thermal fuse, which are separate safety parts. The models above are a sample, not a full list. Confirm your model number against your dryer's parts diagram, or contact our support team to verify fit before ordering. Key Features Genuine OEM Whirlpool cycling thermostat Rated L155-25: cuts out at about 155°F and cycles back on after a 25°F drop Keeps dryer temperature steady by cycling the heating element on and off Resolves no-heat, overheating, and inconsistent-temperature symptoms Fits Whirlpool, Kenmore, Maytag, KitchenAid, and other Whirlpool-built dryers Medium-difficulty repair with basic hand tools Product Specifications Part Number WP3387134 OEM Part Number WP3387134 Part Type Dryer Cycling Thermostat Condition Genuine OEM Temperature Rating L155-25 (Cuts Out ~155°F, 25°F Differential) Application Whirlpool, Kenmore, Maytag, KitchenAid & Related Dryers Installation Notes ⚠️ Unplug Power Before Installing Unplug the dryer or switch off its circuit breaker before beginning, and shut off the gas supply first on gas models. Wear work gloves, as the cabinet edges are sharp. Remove the panel that gives access to the heater housing per your model's service guide, note the wire terminal positions, and disconnect them from the old thermostat. Remove the thermostat, install the new one in the same position, and reconnect the wires. A screwdriver and needle-nose pliers are typically all you need. Before closing the dryer, clean the lint trap and check the exhaust vent for restrictions, since poor airflow is a common cause of overheating. Frequently Asked Questions My dryer isn't heating or runs too hot. Is this the part I need? A failed cycling thermostat can cause either symptom. It may stay open and prevent heat, or stay closed and let the dryer overheat. Check for a clogged vent and test the thermostat for continuity before replacing it. What's the difference between the cycling thermostat and the high limit thermostat? The cycling thermostat controls normal drying temperature by switching the heating element on and off. The high limit thermostat and thermal fuse are separate safety devices that cut power if the dryer overheats. This listing is for the cycling thermostat only. How do I test this thermostat? With the dryer unplugged and the wires removed, check for continuity across the terminals with a multimeter at room temperature. A properly working cycling thermostat should show continuity when cool. No continuity means it has failed. Will this fit my dryer? It fits many Whirlpool-built dryers, but the model list above is only a sample. Check your model number against your parts diagram, or contact our support team and we'll verify it before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

W11457841 Genuine OEM Whirlpool Washer Lid Strike The W11457841 is a Genuine OEM Whirlpool replacement washer lid strike compatible with select Whirlpool, Maytag, and Kenmore HE top-load washers — including the Whirlpool WTW5100, WTW5105, WTW6120, WTW7120, WTW8120, WTW8127 series, and the Maytag MVW6200, MVW6230, MVW7230, MVW7232, MVW8230 series. The lid strike is the plastic component attached to the underside of the washer lid that physically engages the lid lock mechanism when the lid is closed. As the lid lowers into place, the strike enters the lock slot and activates the lid switch — signaling the control board that the lid is securely closed and the washer is safe to start agitation and spin. When the lid strike fails — typically by breaking off, cracking, or wearing down — the lid lock can't be properly activated, and the washer will not start, will stop mid-cycle, or will refuse to advance to the spin cycle. As a Genuine OEM part manufactured by Whirlpool to factory specifications, the W11457841 is the current production part, directly superseding W11091027. It also replaces 4959179, AP6987306, EAP16218028, PD00061788, and PS16218028. Installation is fast and simple — a counterclockwise twist removes the old strike, and a clockwise twist installs the new one. Installs in under 5 minutes, no special tools required. Quick Answer The W11457841 Genuine OEM Whirlpool Washer Lid Strike fixes Whirlpool, Maytag, and Kenmore HE top-load washers that won't start, won't lock the lid, stop mid-cycle, or won't advance to spin because the lid strike is broken or worn. Plastic strike that attaches to the underside of the washer lid and activates the lid lock and switch. Twist-in installation. Genuine OEM. Replaces W11091027, 4959179, AP6987306, EAP16218028, PD00061788, PS16218028. Compatible with Whirlpool WTW5100/5105/6120/7120/8120/8127 and Maytag MVW6200/6230/7230/7232/8230 series. Common Problems This Part Fixes Washer not starting — lid strike not engaging the lid lock Lid won't lock at the start of the cycle Washer stops mid-cycle with a lid-related fault Washer fills with water but won't agitate or advance to spin Lid strike visibly broken, cracked, or missing on the underside of the lid Strike worn down — physically fits the lock slot but no longer activates the lid switch Repeated lid lock errors despite the lid appearing to close normally Replaces Part Numbers This washer lid strike directly replaces the following OEM and cross-reference part numbers: W11457841, W11091027, AP6987306, AWP44638, PD00061788, EAP16218028, PS16218028. W11457841 is the current production part superseding W11091027. Contact our support team with your model number if you need confirmation before ordering. Compatibility This lid strike is compatible with select HE top-load washers from the following brands and series: Whirlpool top-load washers — WTW5100HC0, WTW5100HC1, WTW5100HC2, WTW5100HW0, WTW5100HW1, WTW5100HW2 series Whirlpool top-load washers — WTW5105HC0, WTW5105HC1, WTW5105HC2, WTW5105HW0, WTW5105HW1, WTW5105HW2 series Whirlpool top-load washers — WTW6120HC0, WTW6120HC1, WTW6120HC2, WTW6120HW0, WTW6120HW1, WTW6120HW2 series Whirlpool top-load washers — WTW7120HC0, WTW7120HW0 series Whirlpool top-load washers — WTW8120HC0, WTW8120HW0 series Whirlpool top-load washers — WTW8127LC0, WTW8127LC1, WTW8127LW0 series Maytag top-load washers — MVW6200KW0, MVW6200KW1, MVW6200KW2, MVW6200KW3 series Maytag top-load washers — MVW6230HC0, MVW6230HC1, MVW6230HC2, MVW6230HW0, MVW6230HW1, MVW6230HW2 series Maytag top-load washers — MVW6230RHW0, MVW6230RHW1, MVW6230RHW2 series Maytag top-load washers — MVW7230HC0, MVW7230HW0, MVW7230HW1 series Maytag top-load washers — MVW7232HC0, MVW7232HW0, MVW7232HW2 series Maytag top-load washers — MVW8230HC0 series Kenmore / Sears top-load washers (Whirlpool-built — select 110-series models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Genuine OEM part manufactured by Whirlpool to factory specifications — guaranteed fit and performance Plastic strike attaches to the underside of the washer lid and engages the lid lock mechanism when the lid closes Activates the lid switch to signal the control board that the lid is securely closed and the washer is safe to start Twist-in/twist-out installation — no tools or hardware required; counterclockwise to remove, clockwise to install Current production part — directly supersedes W11091027 Replaces W11091027, 4959179, AP6987306, EAP16218028, PD00061788, and PS16218028 Compatible with Whirlpool WTW5100/5105/6120/7120/8120/8127 and Maytag MVW6200/6230/7230/7232/8230 series HE top-load washers, plus select Kenmore Whirlpool-built models Fast DIY repair — installs in under 5 minutes Product Specifications Part Number W11457841 Supersedes W11091027 Part Type Washer Lid Strike Condition Genuine OEM Application HE Top-Load Washers (Whirlpool/Maytag/Kenmore platform) Material High-strength plastic Installation Twist-in (clockwise) / twist-out (counterclockwise) — no tools required Mounting Location Underside of washer lid Compatible Brands Whirlpool, Maytag, Kenmore Installation Notes ⚠️ Unplug Washer Before Starting — Wear Work Gloves Disconnect power before beginning. Wear work gloves to protect your hands. Open the washer lid and locate the lid strike on the underside of the lid — it's the small plastic peg that drops into the lock slot when the lid is closed. To remove the old strike: rotate the strike counterclockwise until the retaining tab breaks free and pulls back, then pull the old strike straight out. To install the new W11457841: align it with the mounting hole in the same orientation as the old one, and rotate clockwise until you hear or feel the retainer tab click into place. Close the lid and confirm the strike engages the lock slot properly. Restore power, start a test cycle, and confirm the lid locks and the washer begins normal operation. Tools needed: work gloves only — no tools required for the strike itself. Frequently Asked Questions What's the difference between the lid strike, lid lock, and lid switch? These three components work together as a safety system. The lid strike (W11457841) is the small plastic peg attached to the underside of the lid that physically enters the lock slot when the lid closes. The lid lock is the mechanism in the washer cabinet that grips the strike and physically locks the lid closed during the spin cycle. The lid switch is the electrical sensor inside the lock assembly that signals the control board when the strike is engaged. If the strike is broken or missing, none of the three can do their job — even if the lock and switch are working perfectly. Replacing just the strike often resolves "won't start" issues without needing to replace the more expensive lock assembly. What is the difference between W11457841 and W11091027? These are the same lid strike across production revisions. W11091027 was the earlier OEM part number, and W11457841 is the current production version that Whirlpool issued as a direct replacement. Both parts are physically and functionally identical — if your washer's parts diagram shows W11091027, the W11457841 is the correct current replacement, and this listing covers both numbers. My washer won't start and the lid seems to close normally — could this be the strike? Yes, this is one of the most common symptoms of lid strike failure on compatible Whirlpool and Maytag washers. Even though the lid appears to close, if the strike has cracked or worn down it may not physically engage the lock or activate the switch correctly. Visually inspect the strike on the underside of the lid — if it's broken, missing, or chipped, replacement is straightforward. If the strike looks intact and the washer still won't start, the lid lock assembly itself or the wiring harness may need attention. Do I really not need any tools to install this? Correct — the W11457841 lid strike uses a twist-in design with no screws or hardware. To remove the old strike, rotate it counterclockwise until the internal retaining tab breaks free, then pull it out. To install the new one, push it into the mounting hole and twist clockwise until it clicks into place. The whole replacement typically takes under 5 minutes once you have the new part in hand. Work gloves are recommended to protect your hands while gripping the small plastic part, but no other tools are needed. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It is the exact same lid strike installed in compatible Whirlpool, Maytag, and Kenmore HE top-load washers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 280187 Washer Drain Pump Assembly The XPARTCO 280187 is an aftermarket replacement drain pump assembly for Whirlpool-built front-load washers sold under the Whirlpool, Kenmore, Kenmore Elite, Maytag, KitchenAid, and Amana names. The drain pump pushes water out of the tub through the drain hose at the end of the wash and rinse stages. When it clogs, wears out, or seizes, the washer can stop with water still in the drum, throw drain errors, stop before the spin cycle, leak, or make loud humming or grinding noises. This is a complete drain pump assembly, including the pump motor and housing, so it replaces the whole unit rather than just an internal part. The pump sits at the base of the washer behind the lower front panel, and the swap typically takes 15–30 minutes with common hand tools. Quick Answer The XPARTCO 280187 Drain Pump Assembly fixes a Whirlpool-built front-load washer that won't drain, leaves water in the drum, stops before spinning, leaks from the pump, or makes loud noise during draining. Complete pump motor and housing, aftermarket replacement. Classic symptom: the cycle stalls with water still in the tub, or you hear a loud hum or grind while it tries to drain. Common Problems This Part Fixes Washer won't drain, or water is left in the drum after the cycle Drain error codes or the cycle stopping before the spin Loud humming, grinding, or rattling while the washer drains Water leaking from the pump or its housing Pump motor seized or not running Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This drain pump assembly replaces the following part numbers: 280187, 1200164, 285998, 8181684, 8182819, 8182821, AH1485610, AP3953640, AWP39453, EA1485610, EAP1485610, PD00002352, PS1485610 These are Whirlpool's current and earlier numbers for this pump. If your old pump or parts diagram shows any of them, this is the matching replacement. Compatibility This pump is listed for select front-load washers from: Whirlpool, including Duet models such as WFW9400VE03, WFW9500TW03, and WFW9600TW02 Kenmore and Kenmore Elite, including 11042822200, 11042926200, 11045962400, and 11045966403 Maytag, including MHWE400WR00 and MHWE400WW0 KitchenAid, including KHWS02RWH0 Amana Note: The model list above is only a sample, since this pump fits many more models. Confirm fit by matching the number on your old pump or parts diagram against the Replaces list, or contact our support team with your model number and we'll verify before you order. This pump is for front-load washers and is not intended for top-load machines. Key Features Aftermarket replacement drain pump assembly Complete unit with pump motor and housing Restores full draining so cycles finish and the washer can spin Cross-references to Whirlpool 280187, 285998, 8181684, 8182819, and 8182821 Fits select Whirlpool, Kenmore, Maytag, KitchenAid, and Amana front-load washers Typical installation 15–30 minutes with common hand tools Product Specifications Part Number XP280187 OEM Part Number 280187 Part Type Washer Drain Pump Assembly Condition Aftermarket Replacement Included Pump Motor and Housing Application Select Whirlpool, Kenmore, Kenmore Elite, Maytag, KitchenAid & Amana Front-Load Washers Installation Notes ⚠️ Unplug Power and Expect Water Unplug the washer and turn off the water supply before starting. Remove the lower front panel to reach the pump at the base of the washer, then drain any residual water into a shallow pan or with a wet/dry vacuum, using the drain hose or the small drain cap if your model has one. Disconnect the wiring harness from the pump, then loosen the clamps holding the hoses and pull the hoses off. Remove the pump's mounting screw and take out the old pump. Fit the new pump in the same position, reattach the hoses with the clamps (replace worn clamps if needed), and reconnect the wiring harness. Check that the pump and hose connections are secure, replace the front panel, restore power and water, and run a drain cycle while checking for leaks. Common tools include a nutdriver or Torx driver, screwdrivers, and pliers. Frequently Asked Questions My washer won't drain. Is this the part I need? A failed or clogged drain pump is one of the most common causes. Before replacing it, check the drain hose and the pump filter for a clog, such as a sock or coin. If the filter is clear but the pump hums, grinds, or doesn't run, replacing the pump should fix it. Does this include the pump motor? Yes. This is the complete assembly, with the pump motor and housing. My old pump is marked 285998, 8181684, 8182819, or 8182821. Will this work? Yes. All of those are earlier Whirlpool numbers for this pump, and 280187 is the current number. Will this fit my top-load washer? It is intended for front-load washers. Contact our support team with your model number if you're unsure, and we'll confirm before you order. Is this an OEM part? No. This is an XPARTCO aftermarket replacement built to match the Whirlpool 280187. If you prefer a genuine OEM pump, contact us. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

EXP651 Dryer Belt and Idler Pulley Kit Replaces WPW10112954, W10837240 The EXP651 is an aftermarket dryer repair kit containing two essential drum drive components for select Whirlpool, Maytag, Amana, Kenmore, KitchenAid, Crosley, Admiral, Inglis, and Roper dryers. The kit includes one drum belt (replaces WPW10112954) and one idler pulley assembly with bracket (replaces W10837240) — the two parts most commonly worn together when a dryer drum stops spinning or becomes noisy. Replacing both the belt and idler pulley at the same time is the smart repair choice. Since the dryer must be disassembled to access either part, doing both in one repair saves you from having to take the machine apart again if the second part fails shortly after. This kit covers the two most common failure points in the Whirlpool-family dryer drum drive system. Quick Answer The EXP651 Dryer Belt and Idler Pulley Kit fixes dryers where the drum is not spinning, making loud squeaking or grinding noises, or the belt has broken. Includes one 93-1/4" x 5/16" 5-rib drum belt (WPW10112954) and one idler pulley assembly with bracket (W10837240). Compatible with select Whirlpool, Maytag, Amana, Kenmore, KitchenAid, Crosley, Admiral, Inglis, and Roper dryers. What's in the Kit Part 1 of 2 Dryer Drum Belt — Replaces WPW10112954 93-1/4" L x 5/16" W x 1/8" H · 5-rib Multi-V rubber belt · Wraps around drum and connects to motor and idler pulleys to drive drum rotation Part 2 of 2 Idler Pulley Assembly with Bracket — Replaces W10837240 2-1/8" pulley diameter · 6-1/4" L x 1-1/4" W x 3-7/16" H overall · Plastic/metal construction · Maintains correct belt tension to spin the drum · Fits Whirlpool dryers with lint screen inside door Common Problems This Kit Fixes Dryer drum not spinning — motor runs but drum stays still Loud squeaking, squealing, or grinding noise during operation Clothes not tumbling during the drying cycle Thumping or slapping noise when dryer is running Belt slipping off or repeatedly breaking Burning rubber smell coming from the dryer Dryer drum turning erratically or stopping while motor continues to run Replaces Part Numbers Drum Belt (WPW10112954) cross-references: WPW10112954, W10112954, 1447719, AWP48873, PD00003553, EAP11748388, AP6015116, PS11748388. Idler Pulley Assembly (W10837240) cross-references: W10837240, W10547287, W10547290, 3387372, 3388674, W10118754, W10118756, W10837240VP, AWP41730, PD00025564, FIX11726337, AP5988716, PS11726337, 279640, AP3094197, 279640VP, 2958, 3388672, 697692, TJ279640, W10468057, AH334244, EA334244, ER279640, PS334244. If your part numbers are not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This kit is compatible with select dryers from the following brands: Whirlpool dryers (gas and electric — fits models with lint screen inside door) Maytag dryers (gas and electric) Amana dryers Kenmore / Sears dryers (select Whirlpool-built models) KitchenAid dryers Crosley dryers Admiral dryers Inglis dryers Roper dryers Note: The W10837240 idler pulley fits Whirlpool-family dryers with the lint screen located inside the door. If your dryer has the lint screen on top of the cabinet, a different idler pulley part number may be required. Contact our support team to confirm before ordering. Key Features Two-part kit covers the most common drum drive failures in Whirlpool-family dryers in a single repair Belt: 93-1/4" L x 5/16" W, 5-rib Multi-V rubber — resists cracking, stretching, and heat damage Idler pulley: 2-1/8" diameter pulley with arm and bracket — maintains correct belt tension for smooth drum rotation Replacing both parts together saves a second disassembly if the other part fails soon after Aftermarket replacement built to OEM-equivalent quality standards Belt directly replaces WPW10112954 / W10112954 — no modification required Idler pulley directly replaces W10837240 / W10547287 / W10547290 — no modification required DIY-friendly repair — installs in 30–60 minutes with basic hand tools Product Specifications Kit Part Number EXP651 Condition Aftermarket Replacement Application Gas and Electric Dryers Kit Includes 1x Drum Belt (WPW10112954), 1x Idler Pulley Assembly with Bracket (W10837240) Belt Length 93-1/4 inches Belt Width 5/16 inch Belt Height 1/8 inch Belt Ribs 5 ribs, 4 grooves (Multi-V) Belt Material Rubber Pulley Diameter 2-1/8 inches Pulley Overall Dimensions 6-1/4" L x 1-1/4" W x 3-7/16" H Pulley Material Plastic / Metal Compatible Brands Whirlpool, Maytag, Amana, Kenmore, KitchenAid, Crosley, Admiral, Inglis, Roper Installation Notes ⚠️ Safety First — Unplug Dryer Before Starting Unplug the dryer from the power source (and shut off the gas supply for gas dryers) before beginning any repair. Remove the lint screen, then unscrew the Phillips screws inside the lint screen housing. Use a putty knife to release the top panel clips and lift the top panel. Remove the front panel to access the drum and drive components. Release belt tension at the old idler pulley, lift the drum slightly, and slide the old belt off. Remove the old idler arm assembly by unscrewing the mounting screw, then install the new W10837240 idler pulley assembly and secure with the screw. Loop the new WPW10112954 belt around the drum with the ribbed side facing inward, then route it around the new idler pulley and motor pulley. Consult your model's service manual or a model-specific repair video for the correct belt path. Reassemble and run a test cycle. Tools needed: Phillips screwdriver, putty knife or flat pry tool. Frequently Asked Questions Why should I replace the belt and idler pulley at the same time? The belt and idler pulley wear together — when one fails, the other is usually close behind. Since the dryer must be fully disassembled to access either part, replacing both in a single repair saves you from having to take the machine apart again soon after. It also protects the new belt from being damaged by a worn pulley, and vice versa. How does the W10837240 differ from other Whirlpool idler pulleys? The W10837240 is the updated idler pulley arm and bracket assembly designed for Whirlpool-family dryers that have the lint screen inside the door. It replaces the older W10547287 and W10547290 assemblies. Some older or different Whirlpool models use a different idler pulley style — if you're unsure which one your dryer needs, contact our support team with your model number before ordering. What is the difference between WPW10112954 and W10112954? These are the same belt. WPW10112954 is the updated Whirlpool OEM part number that superseded the original W10112954. Both refer to the identical drum belt included in this kit. Should I also replace the drum rollers at the same time? It depends on the condition of your rollers. Since the dryer is already fully disassembled, it is a good opportunity to inspect the drum support rollers for flat spots, cracks, or wobbling. If they show any wear, replacing them at the same time is recommended to avoid a third disassembly. Check your model's roller part number before ordering. Are these OEM or aftermarket parts? Both parts in this kit are aftermarket replacements built to OEM-equivalent quality standards. They are not genuine Whirlpool OEM parts, but are manufactured to match the dimensions and performance of the original WPW10112954 belt and W10837240 idler pulley assembly. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less