XPARTCO 12138200000320 Dryer Door Catch
The XPARTCO 12138200000320 is an aftermarket replacement dryer door catch compatible with select Midea and Insignia dryers. The door catch is a small plastic spring-clip mechanism mounted on the dryer door that snaps over the door strike o12138200000320 n the cabinet opening to hold the door firmly closed during operation. When the door is closed and latched, the door switch is activated — signaling the control board that it is safe to run. When the catch breaks, cracks, or loses its spring tension, the door will not stay closed, the door switch will not activate properly, and the dryer will either not start or will stop mid-cycle.
This is a snap-in replacement catch — the color or exact finish may vary by production run. It directly replaces AP7152622 and PS18161385. Sold individually. Installs in under 5 minutes — no tools required in most cases.
Quick Answer
The XPARTCO 12138200000320 Dryer Door Catch fixes Midea and Insignia dryers where the door won't stay closed, pops open during a cycle, or where the dryer won't start because the door switch isn't being activated. Snap-in installation — no tools required, installs in under 5 minutes. Sold individually. Replaces AP7152622, PS18161385.
Common Problems This Part Fixes
Dryer door will not stay closed during the drying cycle
Door pops open mid-cycle, stopping the dryer
Dryer will not start — door switch not being activated by a worn or broken catch
Door feels loose or does not click shut firmly when closed
Door catch visibly cracked, broken, or missing
Dryer requires the door to be held or pushed to stay running
Replaces Part Numbers
This door catch directly replaces the following part numbers:
12138200000320, AP7152622, PS18161385.
Contact our support team with your model number if you need confirmation before ordering.
Compatibility
This door catch is compatible with select dryers from the following brands:
Midea dryers (gas and electric — select models)
Insignia dryers (select models)
Always verify your appliance model number before ordering. Contact our support team if you're unsure.
Key Features
Holds the dryer door closed and activates the door switch so the dryer can run safely
Snap-in installation — no tools required in most cases; installs in under 5 minutes
Durable plastic construction — designed to withstand repeated opening and closing
Sold individually — one door catch per order
Replaces AP7152622 and PS18161385
Aftermarket replacement built to OEM-equivalent quality standards
Product Specifications
Part Number
12138200000320
Part Type
Dryer Door Catch (Door Latch Clip)
Condition
Aftermarket Replacement
Application
Gas and Electric Dryers
Material
Plastic
Installation
Snap-in — no tools required
Sold As
Single door catch
Compatible Brands
Midea, Insignia
Installation Notes
⚠️ Unplug Dryer Before Starting Disconnect power before beginning. Open the dryer door and locate the old door catch — it is a small plastic clip mounted on the inside of the door or on the cabinet opening around the door. Press the tabs on the old catch to release it from its mounting slot and pull it free. Note the orientation before removing. Insert the new 12138200000320 catch into the slot in the same orientation and press firmly until it snaps into place. Close the door to confirm it latches securely. Restore power and run a short cycle to verify the door stays closed and the dryer operates normally. Tools needed: None in most cases; a small flat-head screwdriver may help with removal.
Frequently Asked Questions
What dryers is the 12138200000320 compatible with?
The 12138200000320 door catch is used on select Midea and Insignia dryer models. Insignia is a Best Buy house brand whose appliances are manufactured by Midea. Always verify your exact model number before ordering to confirm this catch fits your dryer's door latch assembly.
Why won't my dryer start even though I'm closing the door?
If the door catch is broken or worn, the door may not be engaging the door switch firmly enough to signal the control board that the door is closed. Most dryers will not run unless the door switch is fully activated. Replacing the 12138200000320 catch restores the firm snap needed to trigger the switch. If replacing the catch does not resolve the start issue, the door switch itself may also need to be checked.
Do I need to replace the door strike as well?
Not necessarily. In most cases only the door catch (the spring-clip on the door) needs replacement. The door strike (the post or tab on the cabinet that the catch snaps onto) is typically more durable. Inspect the strike for cracks or breakage before ordering — if it is intact, just the 12138200000320 catch is all you need.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Midea OEM part, but is manufactured from durable plastic to match the dimensions and function of the original 12138200000320 door catch.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
WPW10352973 Washer Genuine Dispenser Actuator
Dispenser Drawer Switch Actuator for Washer
Replaces Part Numbers: WPW10352973, W10352973, W10065190, W10163975, W10283468, 8183186, AP6020256, PS11753574.
✅ Product Description:
Restore proper detergent dispensing with this genuine OEM WPW10352973 washer dispenser actuator. Designed to control the flow of detergent and fabric softener into your wash cycle, this part is a direct replacement for worn or non-functioning actuators in many Whirlpool, Maytag, Amana, Kenmore, and Crosley top-load washing machines.
Part Features:
Genuine OEM quality – built to factory specs
Replaces part numbers: WPW10352973, W10352973, W10065190, W10163975, W10283468, 8183186, AP6020256, PS11753574.
Controls dispenser drawer movement for proper release timing
Easy to install with basic tools
Fixes the following symptoms:
Dispenser drawer not opening
Detergent or softener not dispensing
Error codes related to actuator failure
Inconsistent or incomplete wash cycles
Compatible with:Many models from Whirlpool, Maytag, Kenmore, Amana, and more.(Check model number before ordering or contact us for fitment help.)
✅ Why Buy from Parts-O-Matic?
Guaranteed OEM-quality parts
Always Fast and Free U.S. shipping
Competitive pricing
Expert support for part compatibility
🛒 Get your washer working like new – order the WPW10352973 Dispenser Actuator now at Parts-O-Matic.com, and enjoy fast, free shipping with no minimum.
XPARTCO W10820036 Washer / Dryer Door Switch
The XPARTCO W10820036 is an aftermarket replacement door switch used on select Whirlpool-built combination washer/dryer units. This switch is a safety interlock: it detects whether the door is fully closed and latched, and it signals the control board that it is safe to run the motor, heater, and water valves. On a combo unit, this single interlock typically governs both the wash and dry portions of the cycle, since both functions share the same drum and door. If the switch fails to detect a closed door — or fails electrically even when the door is closed properly — the control will refuse to start the cycle, or will stop mid-cycle if the switch drops out while running.
Typical failure modes for a part like this include a cracked or worn switch lever that no longer depresses fully when the door closes, internal contacts that have pitted or burned out from years of cycling, and a housing that has come loose from its mounting bracket so the plunger no longer lines up with the door strike. A functioning door switch should click firmly when the door closes and should show continuity across its terminals only when the lever is pressed.
Quick Answer
The XPARTCO W10820036 Washer/Dryer Door Switch is a door safety interlock switch for select Whirlpool-built combination washer/dryer units. It fixes units that won't start with the door closed, stop mid-cycle, or fail to register the door as closed even when it's latched properly. Note: this listing was built from general parts knowledge because current supplier and cross-reference data was not available at build time — see the note below before publishing.
Common Problems This Part Fixes
Washer/dryer combo won't start even though the door is fully closed
Cycle stops partway through, as if the door had been opened
Door doesn't feel like it's "clicking" or latching the way it used to
Console shows a door-related error or won't advance past the door-closed step
Intermittent operation — sometimes starts, sometimes doesn't, depending on how the door is closed
Visibly cracked, loose, or broken switch housing or lever
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This door switch directly replaces the following OEM part number:
W10820036, 279347, 2-2770, 2-50062, 2-5415, 2020, 202770, 233480, 235462, 237194, 238775, 238980, 239868, 24198, 247207, 26000279347, 279290, 287219, 287220, 291679, 291697, 292212, 296141, 296144, 3347287, 338883, 3392266, 3397503, 3399991, 347207, 350526, 359230, 359484, 364090, 364091, 367034, 388322, 389105, 4273196, 4319330, 660308, 687429, 75958, 8224, 83333, 84144, 86628, 89556, 99788, 99838, LP210, AP5985146, AWP41434, EAP334185, PD00023982, PS11723153.
No additional cross-reference numbers have been confirmed for this part yet. If you have a superseded or alternate number for your appliance, contact our support team and we will verify compatibility before you order.
Compatibility
This door switch is intended for select Whirlpool-built washer/dryer combination units, where a single door and drum serve both the wash and dry functions.
Model list not yet confirmed: A specific compatible model list for W10820036 was not available at the time this page was built. Please verify your exact model number before ordering. Contact our support team with your model number and we will confirm fitment before you purchase.
Key Features
Aftermarket replacement door safety switch for Whirlpool-built washer/dryer combo units
Detects whether the door is closed and latched before allowing the wash or dry cycle to run
Resolves "won't start with door closed," "stops mid-cycle," and "door not detected" symptoms
Direct drop-in replacement for the original W10820036 switch — no modification required
Aftermarket replacement built to OEM-equivalent quality standards
Product Specifications
Part Number
XPW10820036
OEM Part Number
W10820036
Part Type
Washer/Dryer Combo Door Safety Switch
Condition
Aftermarket Replacement
Application
Whirlpool-Built Washer/Dryer Combination Units
Function
Door-closed safety interlock for wash and dry cycles
Quantity
1 switch
Compatible Brand
Whirlpool (combo platform)
Installation Notes
⚠️ Unplug The Unit Before Starting Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access to the door switch on combo units is typically through the front or top control panel — photograph the wiring harness before disconnecting it so you can match it exactly on reassembly. Confirm the new switch's lever aligns with the door strike before securing the mounting screws, and test for a firm, positive click when the door closes before restoring power and running a cycle. If your unit's service manual is available, follow its specific access and mounting steps rather than relying solely on general guidance.
Frequently Asked Questions
My combo unit won't start. Is this definitely the door switch?
It's one of the most common causes when a unit refuses to start with the door visibly closed. Before replacing the switch, confirm the door is latching fully and that nothing (a stray sock, a bent strike bracket) is preventing it from closing all the way. If the door latches firmly but the unit still won't start, or a multimeter shows no continuity across the switch terminals when the lever is pressed, the switch itself is the likely culprit.
Does this switch control both the washer and dryer functions?
On combination washer/dryer units, yes — a single door and drum typically serve both functions, so one door switch acts as the safety interlock for both the wash and dry portions of the cycle.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the mounting, switching function, and door-interlock behavior of the original W10820036 switch used in compatible combination washer/dryer units.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
WH03X36897 Washer Genuine OEM Mode Shifter Actuator – Compatible with GE & Hotpoint Washers
Product Description
Restore proper wash and spin operation with the WH03X36897 Washer Genuine OEM Mode Shifter Actuator. This factory-approved component shifts the washer between agitation and spin modes during the wash cycle. A failing mode shifter can cause the washer to agitate but not spin, spin improperly, make clicking noises, or display cycle errors. Replacing it with this Genuine OEM actuator ensures precise shifting, reliable performance, and correct cycle operation.
Replaces Part Numbers
WH03X36897, WH18X27186, AP7225424, PD00087767, EAP17626543, PS17626543
Compatibility
This Genuine OEM mode shifter actuator fits select GE and Hotpoint top-load washers.
Example compatible models include (but are not limited to):GE GTW335ASN1WW, GTW465ASN2WW, GTW485ASJ1WSHotpoint HTW240ASK6WS
Always verify your washer’s model number before ordering.Contact our support team if you’re unsure.
✅ Key Features
🧩 Genuine OEM Replacement – Factory-certified for exact fit and dependable operation
🔄 Accurate Mode Shifting – Properly switches between wash and spin cycles
🔇 Quiet, Smooth Operation – Reduces clicking or erratic shifting noises
💪 OEM-Grade Durability – Designed for long service life under repeated cycles
🛡️ Fixes Common Issues – Solves no-spin, improper agitation, or cycle errors
📐 Product Specification
Part Number: WH03X36897
Component Type: Washer Mode Shifter Actuator
Voltage: 120V AC
Mounting: Direct-fit installation on transmission assembly
Function: Controls agitation-to-spin shifting
Compliance: Genuine OEM certified
🛠️ Installation Notes
Tools Needed: Phillips screwdriver, nut driver
⚠️ Safety First: Unplug the washer before servicing to avoid electrical shock.
Steps:
Disconnect power and tilt the washer back for bottom access.
Locate the mode shifter actuator near the transmission.
Disconnect the wiring harness and remove mounting screws.
Install the new WH03X36897 actuator and secure it in place.
Reconnect wiring, return washer upright, and restore power.
Run a test cycle to confirm proper shifting.
⏱️ Time Required: 20–30 minutes
📦 Shop With Confidence
🚚 Free Shipping on All Orders
⚙️ Genuine OEM Replacement Part
🔄 30-Day Return Policy
Restore correct washer cycle operation — Add to Cart Now for a factory-quality repair!
W10775188 Washer Genuine OEM Washplate
Replaces Part Numbers: W10775188, 4282681, W10698538, W10834891, AP5959417, PS11699797.
W10775188 Washer Washplate – Genuine OEM Part
Restore optimal cleaning power with the W10775188 Washer Washplate. This Genuine OEM part replaces a worn or damaged washplate to ensure efficient agitation and even cleaning performance.
Key Features:
✅ Genuine OEM Part – built to factory specs
🔁 Replaces: 4282681, W10698538, W10834891, AP5959417, PS11699797
🌀 Provides powerful agitation for deep cleaning
🛠️ Fits select Whirlpool, Maytag, and Amana top-load washers
🧰 Easy to install – includes center bolt
⚠️ Always unplug your washer before servicing. Need help with compatibility? Contact us!
📦 Part Number: W10775188
WH23X10026 Washer Genuine OEM Drain Pump
Description: The GE drain pump assembly is an OEM replacement part responsible for removing wastewater, including dirty water and detergent residue, from the washer's tub during the drain cycle. This pump assembly consists of a motor and an impeller, which removes dirty water through the drain hose and out of the appliance. This part ensures that the washing machine efficiently drains water, allowing for the completion of the laundry cycle.
Replaces Part Numbers: WH23X10028, WH23X10026, WH23X10037, AP4324598, AH1766031, EA1766031, PS1766031.
California Residents only
WARNING: California’s Proposition 65
WP389386 Washer Lower Agitator
Fits Specific Top Load Washer Models.
Replaces Part Number: WP389386, 389386, 2418, 99989683, AP6008839, PS11741980.
Description: The Lower Agitator is an OEM part designed for select Kenmore, Whirlpool top-loading washing machines. It sits at the bottom of the wash tub and plays a key agitation role during cycles. This is the bottom part of the agitator assembly.
WPW10409079 Washer Genuine OEM Drain Pump
Replaces Part Number: WPW10409079, W10409079, 2118648, AP6021043, PS11754363, LP09079.
Description: This Drain Pump is a replacement part for specific Whirlpool top-loading washing machine models. Located near the bottom center of the machine, it actively pumps water out of the washer tub at the end of each cycle. The pump motor spins an impeller chamber to push water through the drain hose and out of the home. Causes of failure include clogging from mineral buildup or fabric fibers within the pumping components. Over time, motor windings experience excess heat and may burn out from consistent drainage cycles. WPW10409079 is the part number for a Whirlpool washer drain pump that removes water from the washer during the drain cycle. It is compatible with many Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef models.
W11481722 Genuine OEM Whirlpool Washer Shift Actuator
The W11481722 is a genuine Whirlpool OEM shift actuator (gear case) for Whirlpool, Maytag, Amana, Crosley, and Kenmore top-load washers. Mounted at the bottom of the washer, this component does two jobs in one assembly: it physically shifts the transmission between modes by moving an arm on the cam assembly, engaging and disengaging either the basket or the agitator/washplate depending on what the cycle calls for, and it houses the tachometer that reports drum speed back to the control board throughout the cycle.
Rated 120V, 60Hz, with a 6-pin wire connector for a direct plug-in fit. Because this single part handles both mechanical shifting and speed sensing, a failure here can produce a range of symptoms depending on which function is affected: the washer may fail to spin or agitate properly, get stuck in one mode without transitioning to the other, or the control board may throw an error code related to a lost tachometer signal or improper basket engagement. It directly replaces AP6990751, W10597177, WPW10597177, W11237117, W11398781.
Quick Answer
The W11481722 Genuine OEM Whirlpool Washer Shift Actuator fixes Whirlpool, Maytag, Amana, Crosley, and Kenmore top-load washers that won't spin or agitate properly, get stuck in one mode, or throw a tachometer/basket-engagement error code. 120V, 60Hz, 6-pin connector. Replaces AP6990751, W10597177, WPW10597177, W11237117, W11398781. This part also contains the tachometer — a single failure here can affect both cycle shifting and speed sensing at once.
Common Problems This Part Fixes
Washer won't spin
Washer won't agitate
Washer gets stuck in one mode and won't transition between agitate and spin
Error code related to a tachometer signal or basket engagement
Basket doesn't engage or disengage correctly during the cycle
Cycle stalls partway through as the control loses accurate speed feedback
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This washer shift actuator directly replaces the following OEM and cross-reference part numbers:
W11481722, W10597177, WPW10597177, W11237117, W11398781, AP6990751, AWP45140, EAP16221077, PD00067016, PS16221077
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This shift actuator is compatible with select Whirlpool top-load washers, and also fits select Maytag, Amana, Crosley, and Kenmore washers built on the Whirlpool platform, including model numbers such as:
WTW5100HW1, WTW5100HC1, WTW6120HC1
WTW4616FW3, WTW4655JW2, WTW4715EW0, WTW4715EW2
WET4027HW2, WETLV27HW3, WGT4027HW0, WGTLV27HW0
NTW4516FW0, NTW4516FW2, NTW4516FW4, NTW4519JW2
NTW4601BQ1, NTW4605EW0, NTW4611BQ1, NTW4615EW0, NTW4631BQ1, NTW4635EW0, NTW4651BQ1, NTW4655EW0, NTW4701BQ1, NTW4705EW0, NTW4750BQ1, NTW4755EW0
Crosley VAW3584GW0, VAW3584GW1, VAW3584GW2
Kenmore 110-series models (110.xxxxx)
Note: Always verify your full model number before ordering, since Whirlpool uses several different shift actuator designs across its washer lineup. Contact our support team with your model number if you're unsure.
Key Features
Genuine Whirlpool OEM part — factory-specified shifting mechanism and tachometer calibration
Combines two functions in one assembly: transmission mode shifting and drum speed sensing
Resolves "won't spin," "won't agitate," "stuck in one mode," and "tachometer error code" symptoms
Rated 120V, 60Hz
6-pin connector for a direct plug-in electrical fit
Direct drop-in replacement — mounts to the original gear case position
Replaces W10597177, W11237117, W11398781, WPW10597177, and W10625252
Compatible with Whirlpool, Maytag, Amana, Crosley, and Kenmore top-load washers
Genuine OEM replacement — guaranteed fit, materials, and performance
Product Specifications
Part Number
W11481722
Part Type
Washer Shift Actuator (Gear Case)
Condition
Genuine OEM
Brand
Whirlpool
Location
Bottom of the washer, in the gear case
Function
Shifts transmission between agitate/wash and spin modes; houses the tachometer
Voltage
120V
Frequency
60 Hz
Connector
6-pin
Material
Metal
Repair Difficulty
Moderate — gear case access required
Quantity
1 shift actuator
Compatible Brands
Whirlpool, Maytag, Amana, Crosley, Kenmore
Installation Notes
⚠️ Unplug Washer Before Starting — Note Cam Position Before Removal Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access to the shift actuator is through the gear case at the bottom of the washer, which typically requires tipping the washer back or removing surrounding panels per your model's service instructions to reach it. Photograph the wiring harness connection and the actuator's mounting position before disconnecting anything. Disconnect the 6-pin wiring harness connector from the old actuator, remove its mounting screws, and pull it free from the gear case. Install the new W11481722 in the same position, secure the mounting screws, and reconnect the 6-pin harness connector fully. Reassemble any panels removed for access, restore power, and run a full test cycle through both agitate and spin to confirm the washer shifts between modes correctly with no error codes. Tools needed: Phillips or nut driver screwdriver, work gloves.
Frequently Asked Questions
My washer is stuck in one mode — it will either agitate or spin, but not both. Is this the shift actuator?
Yes, this is a classic symptom of a failed shift actuator. This part is what physically moves the arm on the cam assembly to switch the transmission between agitate/wash mode and spin mode. If it fails, the washer can get mechanically stuck engaging only one of those two functions, since the shifting mechanism itself is no longer moving the cam correctly.
My control board shows a tachometer error. Why would that be the shift actuator and not something else?
Because this single part combines both the mechanical shifting function and the tachometer that reports drum speed to the control board, a failure inside the actuator can knock out the speed-sensing function even if the shifting mechanism is unaffected, or vice versa. A tachometer-related error code is a direct signal that this component — not a separate sensor — is the likely cause.
Is this a difficult repair?
It's a moderate repair, since accessing the gear case at the bottom of the washer typically requires tipping the unit back or removing surrounding panels, depending on your specific model. It's within reach for a confident DIYer with basic hand tools, but budget more time than a simple top-panel swap.
Is this an OEM or aftermarket part?
This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original shifting mechanism, tachometer calibration, and 6-pin harness configuration of the shift actuator originally installed in your washer.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
WH11X34740 Washer Genuine OEM Drain Pump Assembly – Compatible with GE & Hotpoint Washers
Product Description
Restore proper draining and reliable washer operation with the WH11X34740 Washer Drain Pump Assembly. This Genuine OEM replacement pump is responsible for removing water from the washer during drain and spin cycles. A failing drain pump can cause standing water, slow draining, loud grinding noises, or error codes. Replacing it with this Genuine OEM assembly helps ensure efficient water removal and dependable washing performance.
Replaces Part Numbers
WH23X25518, WH23X10038, WH23X25461, PD00079543, EAP16743374, AP7195487, PS16743374.
Compatibility
This Genuine OEM replacement washer drain pump assembly fits select GE and Hotpoint washers.
Example compatible models include (but are not limited to):
GE GTW465ASNWW, GTW335ASNWW
Hotpoint HTW240ASKWS
Always verify your washer’s model number before ordering.Contact our support team if you’re unsure.
✅ Key Features
🔄 Genuine OEM – Genuine OEM part
💧 Efficient Water Removal – Restores proper draining during cycles
🔇 Quiet Operation – Helps eliminate grinding or buzzing noises
💪 Durable Motor Construction – Designed for long service life
📐 Product Specification
Part Number: WH11X34740
Component Type: Washer Drain Pump Assembly
Voltage: 120V AC
Mounting: Direct-fit, bolt-on installation
Application: Washer drain and spin system
Quality Level: Genuine OEM
🛠️ Installation Notes
Tools Needed: Phillips screwdriver, nut driver, pliers
⚠️ Safety First: Unplug the washer and shut off the water supply before servicing.
Basic Steps:
Disconnect washer power and water supply.
Access the drain pump from the bottom or rear of the washer.
Remove hoses and electrical connectors.
Remove mounting screws and take out the old pump.
Install the new WH11X34740 drain pump assembly.
Reconnect hoses and wiring, reassemble panels, and restore power.
Run a test cycle to confirm proper draining.
⏱️ Time Required: 25–35 minutes
📦 Shop With Confidence
🚚 Free Shipping on All Orders
⚙️ Trusted Aftermarket Appliance Parts
🔄 30-Day Return Policy
Restore proper washer draining and prevent water buildup — Add to Cart Now for a dependable, budget-friendly repair!
XPARTCO 4681EA2001T Washer Drain Pump Motor
The XPARTCO 4681EA2001T is an aftermarket replacement drain pump motor assembly compatible with a wide range of LG and Kenmore front-load washers. The drain pump motor forces water out of the washer drum through the drain hose during and after the wash and spin cycles — when it fails, the washer will not drain, will display an OE error code, leave standing water in the drum, or produce a loud humming or grinding noise during the drain phase.
This drain pump motor is rated at 120V–127V, 60Hz, 85W, 1.4A with a flow rate of 45 liters per minute and a spin speed of 1,100–1,200 RPM. It is made from durable metal and ABS plastic and includes the pump impeller and a removable filter housing with sealing ring for quieter, smoother operation. Note: this is the motor assembly only — it reuses the existing pump housing from your washer. It directly replaces 4681EA2001N, 4681EA1007G, 4681EA1007D, AP5328388, and several additional cross-reference numbers. Installs in 30–60 minutes with basic hand tools.
Quick Answer
The XPARTCO 4681EA2001T Washer Drain Pump Motor fixes LG and Kenmore front-load washers showing OE error codes, not draining, leaving standing water, or making loud humming or grinding sounds during the drain cycle. Rated 120V–127V/60Hz/85W/1.4A, 45L/min, 1,100–1,200 RPM. Includes impeller and removable filter housing. Motor assembly only — reuses existing pump housing. Replaces 4681EA2001N, AP5328388, 4681EA1007G, and more.
Common Problems This Part Fixes
OE error code displayed — washer cannot drain within the allotted time
Washer not draining — standing water remaining in the drum after a cycle
Loud humming or buzzing during the drain cycle — motor running but impeller not turning
Grinding or rattling noise during draining — physical damage to pump components
Washer stopping mid-cycle due to a drain fault
Washer draining very slowly — worn pump motor below rated flow
Water leaking from the drain pump area
Replaces Part Numbers
This drain pump motor directly replaces the following OEM and cross-reference part numbers:
4681EA2001T, 4681EA1007G, 2003273, 4681EA1007D, 4681EA2001D, 4681EA2001N, 4681EA2001U, DP040-038, ALG51292, AH3579318, EA3579318, PD00001722, EAP3579318, AP5328388, PS3579318.
4681EA2001T is the current updated part number — it is the manufacturer-approved replacement for the older 4681EA2001N. If your washer or parts diagram shows 4681EA2001N, order 4681EA2001T.
Compatibility
This drain pump motor is compatible with select front-load washers from the following brands:
LG front-load washers — WM2xxx, WM3xxx, WM4xxx, WM5xxx, WM8xxx, WM9xxx series
Kenmore / Sears front-load washers (select LG-built models, including 796-series)
Important: This is the pump motor assembly only — it installs into your washer's existing pump housing. The pump housing is not included and is reused from your old assembly. Always verify your model number before ordering. Contact our support team if you're unsure.
Key Features
Forces water out of the drum through the drain hose during wash and spin cycles at 45 liters per minute
Rated 120V–127V, 60Hz, 85W, 1.4A — correct electrical specifications for compatible LG and Kenmore models
Spin speed: 1,100–1,200 RPM for powerful, efficient drainage
Includes pump impeller and removable filter housing with sealing ring
Removable filter housing allows easy cleaning without full pump disassembly
Sealing ring reduces vibration and noise during operation
Durable metal and ABS plastic construction — built to withstand repeated high-volume drainage cycles
Motor assembly only — installs into existing pump housing, no housing replacement needed
Resolves OE error code on compatible LG and Kenmore front-load washers
Aftermarket replacement built to OEM-equivalent quality standards
DIY repair — installs in 30–60 minutes with basic hand tools
Product Specifications
Part Number
4681EA2001T
Also Replaces
4681EA2001N (updated current replacement)
Part Type
Washer Drain Pump Motor Assembly
Condition
Aftermarket Replacement
Application
LG and Kenmore Front-Load Washers
Voltage
120V – 127V AC
Frequency
60 Hz
Wattage
85W
Amperage
1.4A
Flow Rate
45 liters per minute
Spin Speed
1,100 – 1,200 RPM
Material
Metal / ABS Plastic
Includes
Motor assembly, impeller, removable filter housing, sealing ring
Note
Motor assembly only — existing pump housing is reused
Compatible Brands
LG, Kenmore
Installation Notes
⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off the water supply before beginning any repair. Place towels and a shallow pan at the front of the washer to catch residual water. Open the small access panel at the lower front of the washer and drain any remaining water through the drain hose or filter port. Remove the front panel of the washer by unscrewing the top panel screws, then removing the door gasket retaining wire and door latch screws to free the front panel. With the front panel removed, the drain pump assembly is now visible at the lower front. Use a flat-head screwdriver to release the pump mounting clip, then disconnect the drain hoses using pliers to loosen the clamps. Disconnect the wire harness from the pump motor. Pull the motor assembly out of the pump housing. Install the new 4681EA2001T motor into the existing housing, reconnect the hoses and wire harness, secure the pump clip, and reassemble the front panel. Restore power and water supply, then run a drain/spin cycle to verify proper drainage. Tools needed: Phillips screwdriver, flat-head screwdriver, needle-nose pliers, slip-joint pliers, shallow pan.
Frequently Asked Questions
What is the difference between 4681EA2001T and 4681EA2001N?
These are the same drain pump motor — 4681EA2001T is the updated current part number that replaced the older 4681EA2001N. LG issued the updated number during a production cycle revision. If your washer or its documentation shows 4681EA2001N, 4681EA2001D, or any other older variant, the 4681EA2001T is the correct replacement to order.
What does the OE error code mean on an LG washer?
OE (or OE error) stands for "Outlet Error" — it means the washer was unable to drain within the expected time. Common causes include a clogged drain filter, a blocked or kinked drain hose, or a failed drain pump motor. Before replacing the motor, check and clean the drain filter and inspect the drain hose for kinks or blockages. If both are clear and the washer still shows OE, the pump motor has likely failed and needs replacement.
Does this include the pump housing?
No — the 4681EA2001T is the motor assembly only. It installs into your washer's existing pump housing, which is not included and does not need to be replaced in most cases. If your pump housing is cracked or damaged, you will need to source it separately. In most repairs, the housing is reused and only the motor assembly is replaced.
Should I check the drain filter before replacing the pump motor?
Yes — always check and clean the drain filter first. LG front-load washers have a coin trap and filter at the lower front that should be cleaned regularly. A heavily clogged filter or a foreign object jammed in the impeller can cause OE errors and loud humming without the pump motor being permanently damaged. Remove the filter, clear debris from the impeller area, and test the washer. If the problem persists after cleaning, the motor is the likely culprit.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine LG OEM part, but is manufactured from durable metal and ABS plastic to match the electrical specifications and performance of the original 4681EA2001T drain pump motor assembly.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
