Search results for "washer strike"

WH01X10279 Washer Door Boot Outside Clamp Replaces Part Numbers: WH01X10279, 1168582, AH1016305, EA1016305, AGE25430, AP3883931, PS1016305.    

Read more less

XPARTCO 4681EA2001T Washer Drain Pump Motor The XPARTCO 4681EA2001T is an aftermarket replacement drain pump motor assembly compatible with a wide range of LG and Kenmore front-load washers. The drain pump motor forces water out of the washer drum through the drain hose during and after the wash and spin cycles — when it fails, the washer will not drain, will display an OE error code, leave standing water in the drum, or produce a loud humming or grinding noise during the drain phase. This drain pump motor is rated at 120V–127V, 60Hz, 85W, 1.4A with a flow rate of 45 liters per minute and a spin speed of 1,100–1,200 RPM. It is made from durable metal and ABS plastic and includes the pump impeller and a removable filter housing with sealing ring for quieter, smoother operation. Note: this is the motor assembly only — it reuses the existing pump housing from your washer. It directly replaces 4681EA2001N, 4681EA1007G, 4681EA1007D, AP5328388, and several additional cross-reference numbers. Installs in 30–60 minutes with basic hand tools. Quick Answer The XPARTCO 4681EA2001T Washer Drain Pump Motor fixes LG and Kenmore front-load washers showing OE error codes, not draining, leaving standing water, or making loud humming or grinding sounds during the drain cycle. Rated 120V–127V/60Hz/85W/1.4A, 45L/min, 1,100–1,200 RPM. Includes impeller and removable filter housing. Motor assembly only — reuses existing pump housing. Replaces 4681EA2001N, AP5328388, 4681EA1007G, and more. Common Problems This Part Fixes OE error code displayed — washer cannot drain within the allotted time Washer not draining — standing water remaining in the drum after a cycle Loud humming or buzzing during the drain cycle — motor running but impeller not turning Grinding or rattling noise during draining — physical damage to pump components Washer stopping mid-cycle due to a drain fault Washer draining very slowly — worn pump motor below rated flow Water leaking from the drain pump area Replaces Part Numbers This drain pump motor directly replaces the following OEM and cross-reference part numbers: 4681EA2001T, 4681EA1007G, 2003273, 4681EA1007D, 4681EA2001D, 4681EA2001N, 4681EA2001U, DP040-038, ALG51292, AH3579318, EA3579318, PD00001722, EAP3579318, AP5328388, PS3579318. 4681EA2001T is the current updated part number — it is the manufacturer-approved replacement for the older 4681EA2001N. If your washer or parts diagram shows 4681EA2001N, order 4681EA2001T. Compatibility This drain pump motor is compatible with select front-load washers from the following brands: LG front-load washers — WM2xxx, WM3xxx, WM4xxx, WM5xxx, WM8xxx, WM9xxx series Kenmore / Sears front-load washers (select LG-built models, including 796-series) Important: This is the pump motor assembly only — it installs into your washer's existing pump housing. The pump housing is not included and is reused from your old assembly. Always verify your model number before ordering. Contact our support team if you're unsure. Key Features Forces water out of the drum through the drain hose during wash and spin cycles at 45 liters per minute Rated 120V–127V, 60Hz, 85W, 1.4A — correct electrical specifications for compatible LG and Kenmore models Spin speed: 1,100–1,200 RPM for powerful, efficient drainage Includes pump impeller and removable filter housing with sealing ring Removable filter housing allows easy cleaning without full pump disassembly Sealing ring reduces vibration and noise during operation Durable metal and ABS plastic construction — built to withstand repeated high-volume drainage cycles Motor assembly only — installs into existing pump housing, no housing replacement needed Resolves OE error code on compatible LG and Kenmore front-load washers Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 30–60 minutes with basic hand tools Product Specifications Part Number 4681EA2001T Also Replaces 4681EA2001N (updated current replacement) Part Type Washer Drain Pump Motor Assembly Condition Aftermarket Replacement Application LG and Kenmore Front-Load Washers Voltage 120V – 127V AC Frequency 60 Hz Wattage 85W Amperage 1.4A Flow Rate 45 liters per minute Spin Speed 1,100 – 1,200 RPM Material Metal / ABS Plastic Includes Motor assembly, impeller, removable filter housing, sealing ring Note Motor assembly only — existing pump housing is reused Compatible Brands LG, Kenmore Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off the water supply before beginning any repair. Place towels and a shallow pan at the front of the washer to catch residual water. Open the small access panel at the lower front of the washer and drain any remaining water through the drain hose or filter port. Remove the front panel of the washer by unscrewing the top panel screws, then removing the door gasket retaining wire and door latch screws to free the front panel. With the front panel removed, the drain pump assembly is now visible at the lower front. Use a flat-head screwdriver to release the pump mounting clip, then disconnect the drain hoses using pliers to loosen the clamps. Disconnect the wire harness from the pump motor. Pull the motor assembly out of the pump housing. Install the new 4681EA2001T motor into the existing housing, reconnect the hoses and wire harness, secure the pump clip, and reassemble the front panel. Restore power and water supply, then run a drain/spin cycle to verify proper drainage. Tools needed: Phillips screwdriver, flat-head screwdriver, needle-nose pliers, slip-joint pliers, shallow pan. Frequently Asked Questions What is the difference between 4681EA2001T and 4681EA2001N? These are the same drain pump motor — 4681EA2001T is the updated current part number that replaced the older 4681EA2001N. LG issued the updated number during a production cycle revision. If your washer or its documentation shows 4681EA2001N, 4681EA2001D, or any other older variant, the 4681EA2001T is the correct replacement to order. What does the OE error code mean on an LG washer? OE (or OE error) stands for "Outlet Error" — it means the washer was unable to drain within the expected time. Common causes include a clogged drain filter, a blocked or kinked drain hose, or a failed drain pump motor. Before replacing the motor, check and clean the drain filter and inspect the drain hose for kinks or blockages. If both are clear and the washer still shows OE, the pump motor has likely failed and needs replacement. Does this include the pump housing? No — the 4681EA2001T is the motor assembly only. It installs into your washer's existing pump housing, which is not included and does not need to be replaced in most cases. If your pump housing is cracked or damaged, you will need to source it separately. In most repairs, the housing is reused and only the motor assembly is replaced. Should I check the drain filter before replacing the pump motor? Yes — always check and clean the drain filter first. LG front-load washers have a coin trap and filter at the lower front that should be cleaned regularly. A heavily clogged filter or a foreign object jammed in the impeller can cause OE errors and loud humming without the pump motor being permanently damaged. Remove the filter, clear debris from the impeller area, and test the washer. If the problem persists after cleaning, the motor is the likely culprit. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine LG OEM part, but is manufactured from durable metal and ABS plastic to match the electrical specifications and performance of the original 4681EA2001T drain pump motor assembly. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

Genuine OEM Whirlpool Washer Part WP3951632 Washer Genuine OEM Lower Agitator The lower agitator base moves back and forth during the wash cycle to help circulate clothing through the water and detergent. Product Overview The Whirlpool WP3951632 Washer Lower Agitator is the lower half, or base, of the agitator used in compatible top-load washing machines. During the wash cycle, the agitator moves back and forth to circulate clothing through the wash water and detergent for effective cleaning. This is a new Genuine OEM Whirlpool replacement part manufactured to the original equipment specifications for proper fit and operation in compatible models. Quick Answer WP3951632 is the Genuine OEM Whirlpool lower agitator base for select top-load washers. It replaces part number 3951632. This listing is for the lower agitator only; the upper agitator, agitator dogs, cam, cap, bolt, dispenser, and other hardware are not included unless specifically shown in the product photographs. Common Problems This Part May Fix Washer fills and runs but clothing is not agitated properly Lower agitator does not move during the wash cycle Cracked, broken, or damaged agitator fins Worn or stripped center connection on the agitator base Agitator slips on the transmission shaft Poor washing or uneven clothing movement Replaces and Cross-References WP3951632, 3951632, 547649, AP6008904, AWP47252, EAP11742045, PD00004360, PS11742045. WP3951632 is the current manufacturer part number. Other numbers shown are previous manufacturer or retailer cross-reference numbers used to identify the same lower agitator. Compatibility Designed for select Whirlpool-built top-load washers, including certain models sold under the Whirlpool, Amana, Crosley, Estate, Inglis, and Kenmore brand names. Confirmed model examples include: WTW4800BQ1 WTW4816FW1 WTW4816FW3 WTW4850XQ3 LSQ9010PW3 7MWTW1701DQ1 3RGSC9455JQ1 110.20232711 VAW3584GW0 Important: This is only a partial compatibility list. Agitators can look similar but use different shaft connections, heights, fins, and internal components. Verify the complete washer model number before ordering. Key Features Genuine OEM Whirlpool replacement part Lower agitator base for compatible top-load washers Moves clothing through wash water and detergent Durable molded construction Designed for original fit and operation Direct replacement when WP3951632 is specified Replaces original part number 3951632 Product Specifications Manufacturer Part Number WP3951632 Brand Whirlpool Part Type Washer Lower Agitator / Agitator Base Condition New Quality Genuine OEM Application Top-Load Washing Machine Primary Function Moves clothing through wash water during agitation Included One Lower Agitator Base Installation Notes Unplug the washer before beginning the repair. Remove the fabric-softener dispenser or agitator cap, if installed. Remove the inner cap or seal to access the agitator retaining bolt. Use the correct socket and extension to remove the center retaining bolt. Lift the agitator assembly from the washer and separate the upper agitator from the lower base as required. Inspect the agitator bolt, thrust washer, cam, agitator dogs, upper agitator, and transmission shaft for additional wear. Install the new lower agitator in the same position, tighten the retaining bolt securely, and reinstall all caps or dispenser components. Installation tip: A washer that does not agitate can also have worn agitator dogs, a damaged cam, a loose bolt, a failed drive component, or a transmission problem. Diagnose the appliance before ordering when the cause is uncertain. Frequently Asked Questions Is WP3951632 a genuine Whirlpool part? Yes. WP3951632 is a Genuine OEM Whirlpool replacement lower agitator. Does this listing include the complete agitator assembly? No. This part is the lower agitator base only. The upper agitator, cam, agitator dogs, cap, dispenser, bolt, and related hardware are separate unless specifically shown or stated. What part number does WP3951632 replace? WP3951632 replaces the previous manufacturer part number 3951632. Will this fit every Whirlpool washer? No. It fits only select top-load washer models. Verify your complete model number and required manufacturer part number before purchasing. Should I replace the agitator dogs at the same time? Inspect the agitator dogs and cam while the agitator is disassembled. Replace them separately if they are worn, rounded, cracked, or slipping. Shop With Confidence Purchase the correct Genuine OEM replacement part for dependable fit and performance. Verify your washer model number before ordering, and contact our parts team when compatibility assistance is needed. Genuine OEM WhirlpoolFast U.S. ShippingCompatibility SupportSecure Checkout

Read more less

W11700916 Washer Genuine OEM Door Latch The W11700916 is a genuine Whirlpool OEM lid lock assembly for Whirlpool top-load washers, and also fits select Maytag and Kenmore models. This assembly ensures the washer's lid remains securely locked during the wash and spin cycle, preventing access to the moving parts inside while the drum is in motion and confirming to the control board that the lid is safely closed before the cycle can proceed. This part is a superseding design, replacing the earlier W11394572 lid latch. Over time, the internal locking mechanism can wear out or fail electrically. A failing lid lock typically shows up as the lid not locking properly during a cycle, or the washer failing to start at all, since the control board won't proceed without confirmation the lid is securely closed. It directly replaces W11543566, W11394572, W11032875, AP7219279, and PS17217010. Quick Answer The W11700916 Washer Genuine OEM Door Latch fixes Whirlpool, Maytag, and Kenmore top-load washers where the lid isn't locking properly, or the washer won't start at all. Replaces W11543566, W11394572, W11032875, AP7219279, PS17217010. This is a newer superseding lid lock design — if your washer's original latch is one of the numbers it replaces, this is the correct current part to order. Common Problems This Part Fixes Lid isn't locking properly during the wash or spin cycle Washer won't start at all Lid pops open or unlocks unexpectedly mid-cycle Cycle stalls at the start and won't proceed to wash or spin Washer pumps or agitates but won't spin because the lid isn't sensed as locked Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer door latch directly replaces the following OEM and cross-reference part numbers: W11700916, W11394572, W11032875, W11543566, EG-380900, AP7219279, AWP46729, EAP17217010, OEM21657846, PD00085319, PS17217010 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This lid lock assembly is compatible with select Whirlpool top-load washers, and also fits select Maytag and Kenmore washers built on the Whirlpool platform, including model numbers such as: MVW8230HC0, MVW7230HW0, MVW7230HC0, MVW7232HC0, MVW7232HW0 MVW6200KW0, MVW6230RHW0, MVW6230HC1, MVW6230HW1, MVW6230HC0, MVW6230HW0 WTW8120HC0, WTW8120HW0 WTW7120HC0, WTW7120HW0 WTW6120HC1, WTW6120HW1, WTW6120HW0, WTW6120HC0 WTW5100HC0, WTW5100HW0, WTW5105HW0, WTW5105HC0 Note: This is a distinct lid lock design from other Whirlpool washer latches already in our catalog, such as our W10404050 and W10810403 listings — Whirlpool has used multiple different lid lock designs across its top-load washer lineup over the years. Always verify your full model number before ordering, or match the exact part number printed on your old latch. Contact our support team with your model number if you're unsure. Key Features Genuine Whirlpool OEM part — factory-specified locking mechanism Confirms lid closure to the control board and locks the lid during wash/spin Resolves "lid won't lock," "washer won't start," and "lid pops open mid-cycle" symptoms Superseding design — current replacement for the earlier W11394572 latch Direct drop-in replacement — matches the original mounting and harness connector Replaces W11543566, W11394572, W11032875, AP7219279, and PS17217010 Compatible with Whirlpool, Maytag, and Kenmore top-load washers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number W11700916 Part Type Washer Lid Lock Assembly / Door Latch Condition Genuine OEM Brand Whirlpool Application Top-Load Washers Function Locks the lid during wash/spin and confirms closure to the control board Supersedes W11394572 Repair Difficulty Easy to Moderate — basic hand tools, novice repair experience Quantity 1 lid lock assembly Compatible Brands Whirlpool, Maytag, Kenmore Installation Notes ⚠️ Unplug Washer Before Starting Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Open the washer lid and locate the lid lock assembly mounted on its underside, typically secured with a couple of screws. Photograph the wiring harness connection before disconnecting anything. Remove the mounting screws, disconnect the wiring harness connector from the old assembly, and pull it free. Install the new W11700916 in the same position, reconnect the wiring harness connector fully, and secure the mounting screws. Restore power and run a test cycle to confirm the lid locks securely, the washer starts and completes a full cycle, and the lid unlocks normally once finished. Tools needed: multi-screwdriver, work gloves. Frequently Asked Questions My washer's lid isn't locking properly. Is this the part I need? Yes, this is the classic symptom this assembly addresses. Since the control board won't proceed into the wash or spin cycle without confirmation the lid is closed and locked, a worn or failing lock assembly can prevent the washer from starting or cause it to stop mid-cycle if the lock fails while running. My old part number is W11394572. Is this the same thing? This W11700916 is the current superseding part for W11394572 — Whirlpool has updated the part number, and this is the correct part to order now even if your washer's original latch was labeled with the older number. Is this the same latch as other Whirlpool washer lid locks you sell? Not necessarily — Whirlpool has used several different lid lock designs across its top-load washer lineup over the years, including other designs found elsewhere in our catalog. Always match your exact original part number, or your full washer model number, rather than assuming any "Whirlpool lid lock" will fit your machine. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original locking mechanism and wiring harness configuration of the lid lock assembly designed for your washer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WP21352320 Genuine OEM Whirlpool Washer Drive Belt The WP21352320 is a genuine Whirlpool OEM drive belt for Whirlpool top-load washers. This belt connects the drive motor to the transmission at the bottom of the washer, and it's what actually spins the basket during the wash and spin cycles. Unlike a dryer's drum belt, which simply tumbles a drum, this washer drive belt has to transfer real torque to spin a heavy, water-filled basket, which puts it under considerably more mechanical stress. Measuring approximately 51" long and 3/8" wide. A worn or broken belt produces a distinctive set of symptoms: the washer may not spin at all, spin only slowly, agitate poorly or not at all, fail to drain properly since the pump relies on the same drive system, or produce a burning smell or loud grinding noise as a worn belt slips against the pulley. One useful diagnostic tip worth knowing: a belt can look intact at a glance but still be worn out — if the sides of the belt appear shiny or glazed rather than matte, that's a sign of slippage-related wear even without a visible crack. It directly replaces 21001478, 21352320, 35-2073, 35-2320, AP6005822, WP21352320VP, and PS11738882. Quick Answer The WP21352320 Genuine OEM Whirlpool Washer Drive Belt fixes Whirlpool, Maytag, Roper, Admiral, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, Norge, Amana, Kenmore, KitchenAid, and Ikea top-load washers with a drum that won't spin, spins slowly, won't agitate, won't drain, or produces a burning smell or loud grinding noise. Approximately 51" long, 3/8" wide. Replaces 21001478, 21352320, 35-2073, 35-2320, AP6005822, WP21352320VP, PS11738882. A belt can look intact but still be worn out — check the sides for a shiny, glazed appearance, which indicates slippage wear even without a visible crack. Common Problems This Part Fixes Washer drum won't spin, or spins only slowly Washer won't agitate during the wash cycle Washer won't drain properly Burning smell coming from the washer during operation Loud grinding noise from underneath the washer Washer that shakes or moves excessively during spin Washer that won't start or stalls partway through a cycle Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer drive belt directly replaces the following OEM and cross-reference part numbers: WP21352320, 21352320, 21001478, 35-2073, 35-2320, 35-3662, PD00002418, EAP11738882, AP6005822, AWP46532, PS11738882, WP21352320VP If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drive belt is compatible with select Whirlpool top-load washers, and also fits select Maytag, Roper, Admiral, Hardwick, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, Norge, Modern Maid, Amana, Kenmore, KitchenAid, and Ikea washers built on the Whirlpool platform, including model numbers such as HAV3460AWW. Note: Always verify your full model number before ordering, since Whirlpool uses several different drive belts across its top-load washer lineup. Contact our support team with your model number if you're unsure. Key Features Genuine Whirlpool OEM part — factory-specified length, width, and material Connects the drive motor to the transmission to spin the basket Resolves "won't spin," "won't agitate," "won't drain," "burning smell," and "grinding noise" symptoms caused by belt failure Approximately 51" long, 3/8" wide Direct drop-in replacement matching the original belt routing Replaces 21001478, 21352320, 35-2073, 35-2320, AP6005822, WP21352320VP, and PS11738882 Compatible with Whirlpool, Maytag, Roper, Admiral, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, Norge, Amana, Kenmore, KitchenAid, and Ikea top-load washers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number WP21352320 Part Type Washer Drive Belt Condition Genuine OEM Brand Whirlpool Application Top-Load Washers Length Approx. 51 in. Width 3/8 in. Attaches To Motor pulley and transmission Repair Difficulty Medium — basic hand tools required Quantity 1 drive belt Compatible Brands Whirlpool, Maytag, Roper, Admiral, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, Norge, Amana, Kenmore, KitchenAid, Ikea Installation Notes ⚠️ Unplug Washer And Shut Off Water Supply Before Starting — Consider The Motor Pulley While You're In There Disconnect power at the outlet or shut off the circuit breaker, and shut off both the hot and cold water supply valves before beginning. Pull the washer out from the wall for full access. Wear work gloves. Locate the drive belt around the motor at the bottom of the washer. Use a flathead screwdriver or hex wrench to remove the screws holding the motor bracket in place, which releases tension on the belt. Carefully slide the motor bracket off the motor, and use pliers if needed to work the old belt off the pulley. While the bottom of the washer is accessible, this is a good time to inspect the motor pulley for wear as well, since it's a related component you'll already have exposed. Install the new WP21352320 belt around the pulley and transmission, following the same routing as the old belt, and make sure it's seated securely and tightened properly — a loose or improperly seated belt will slip and wear out quickly. Reattach the motor bracket with its screws. Restore the water supply and power, then run a test cycle to confirm the washer spins, agitates, and drains normally with no unusual noise. Tools needed: multi-bit screwdriver, hex wrench, standard pliers, work gloves. Frequently Asked Questions My belt looks fine — no cracks or visible damage. Could it still need replacing? Yes, and this is a common source of confusion. A belt can appear intact with no cracks and still be worn out. Check the sides of the belt closely: if they look shiny or glazed rather than having a matte, textured surface, that glazing indicates the belt has been slipping against the pulley, which is a clear sign of wear even without visible cracking. My washer pumps and drains but the drum spins slowly or not at all. Is this the belt? Yes, this is one of the most direct symptoms of a worn or slipping drive belt. Since this belt is what actually transfers the motor's power to spin the basket, a worn belt can slip under load, causing slow or absent spinning even though the motor itself and the drain pump are both working normally. Should I replace the motor pulley at the same time? It's worth inspecting while you have the bottom of the washer accessible, even if you don't end up replacing it. A worn pulley can accelerate wear on a brand-new belt, so checking its condition during this repair is a reasonable precaution, especially if your old belt showed the glazed, slipping-related wear pattern. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original length, width, and routing configuration of the drive belt originally installed in your washer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WH01X27954 Washer Lid Switch (Old Style) Product Overview The XPARTCO WH01X27954 Washer Lid Switch (Old Style) is designed to restore proper lid detection and washer operation. This high-quality replacement detects whether the washer lid is closed, allowing safe operation during wash and spin cycles. A broken or faulty switch can cause the washer not to start, stop mid-cycle, or fail to spin. Replacing it with this durable XPARTCO switch restores normal functionality and safety performance. Old-style GE lid switch (does not require harness replacement). Quick Answer If your washer will not spin, drain, or start properly, a faulty WH01X27954 lid switch may be the cause. Replacing this old style washer lid switch helps restore normal washer operation and cycle performance. Replaces Part Numbers Replaces OEM part number: WH08X32697, WH01X27954, WH08X31577, WH01X24114, WH01X26114, 290D1580P001, 290D1580P004, 290D1580P002, 290D1580P003, WH08X31577, AP7015047, PS16554755. Compatibility This washer lid switch is compatible with select GE, Hotpoint, and other compatible top-load washers that use the old style lid switch design. Example compatible models include (but are not limited to): GE GTW220ACK1WW GTW220ACK2WW GTW220ACK3WW GTW220ACK4WW GTW220ACK5WW GTW220ACK6WW GTW220ACK7WW GTW220ACKWW GTW330ASK0WW GTW330ASK1WW GTW330ASK2WW GTW330ASK3WW GTW330ASK4WW GTW330ASKWW GTW335ASN0WW GTW335ASN2WW GTW335ASNWW GTW460AMJ0WW GTW460AMJ1WW GTW460AMJ2WW GTW460AMJ3WW GTW460AMJ4WW GTW220ACK4WW GTW220ACK5WW GTW220ACK6WW GTW220ACK7WW GTW220ACKWW GTW330ASK0WW GTW330ASK1WW GTW335ASN0WW. GE Top-Load Washers Hotpoint Washers Old Style Lid Switch Applications Always verify your washer’s model number before ordering. Contact our support team if you’re unsure. Common Problems This Part Fixes Washer not spinning Washer not draining Washer not starting cycle Lid switch not detecting closed lid Key Features Designed for old style washer lid switch applications Helps restore safe and proper washer operation High-quality aftermarket replacement Durable construction for reliable performance Product Specifications Part Number: WH01X27954 Part Type: Washer Lid Switch Brand: XPARTCO Condition: New OEM / Aftermarket: Aftermarket Application: Top-Load Washers Style: Old Style Troubleshooting Guide Washer fills but does not spin → Lid switch may be faulty Washer will not start cycle → Lid switch may not detect closed lid Washer stops before spin cycle → Defective lid switch can interrupt operation When Should You Replace This Lid Switch? Replace this lid switch if your washer does not start, spin, or drain properly, or if the switch no longer detects when the lid is closed. Installation Notes ⚠️ Disconnect power before installation. Access the lid switch area according to your washer design and install the replacement securely. Refer to your appliance manual if needed. Related Parts Washer Lid Strike Washer Timer Washer Door or Lid Lock Components Frequently Asked Questions Will this lid switch fit my washer?This switch fits select GE and compatible washers that use the old style lid switch. Always verify your model number. What does a washer lid switch do?It detects whether the washer lid is closed so the machine can operate safely. What are signs of a bad lid switch?Common signs include the washer not spinning, not starting, or stopping before the cycle completes. Is this the old style version?Yes, this listing is for the old style WH01X27954 washer lid switch. Shop With Confidence Parts-O-Matic is a U.S.-based appliance parts retailer specializing in OEM and high-quality aftermarket parts. We offer fast shipping, reliable products, and expert support. Fast Shipping Quality Tested Parts Compatibility Support  

Read more less

W10919003 Washer Genuine OEM Drain Pump Replaces Part Numbers: W10919003, 4461359, W10775446, AP6038235, PS11770076. Description: This Water Pump is a Genuine OEM replacement part for specific Maytag, Kenmore, Whirlpool washing machine models. It plays a crucial role in circulating water throughout the wash cycles and draining the used water from the tub.

Read more less

DC61-02432A Genuine OEM Samsung Washer Suspension Spring Guide The DC61-02432A is a genuine Samsung OEM suspension spring guide (bracket) for Samsung and select Kenmore washers. This small but structurally important bracket connects the washer's outer frame to one of the suspension springs that support the wash tub, keeping the spring correctly seated and aligned as the tub moves during fill, wash, and especially spin. The tub itself hangs suspended inside the cabinet, and it's this network of springs and guides that lets it move and absorb vibration without banging against the surrounding frame or panels. Because this guide holds the spring in its proper working position, a cracked, worn, or broken guide lets the spring drift out of alignment or lose tension where it seats. The result is usually excessive tub movement, unusual banging or knocking noises (especially during spin), or a washer that seems to "walk" or vibrate more than it used to. Left unaddressed, a spring that has come loose from a failed guide can allow the tub to strike the cabinet repeatedly, accelerating wear on nearby components. It directly replaces AP5581510, 2069491, and PS4206750. As a genuine OEM part, the DC61-02432A is manufactured by Samsung to factory specifications — guaranteed fit, materials, and performance. Quick Answer The DC61-02432A Genuine OEM Samsung Washer Suspension Spring Guide fixes Samsung and select Kenmore washers with excessive tub movement, unusual banging or knocking noise (especially during spin), a washer that vibrates or "walks" more than it used to, or a suspension spring that has come loose or shifted out of position. Connects the washer frame to the suspension spring. Replaces AP5581510, 2069491, PS4206750. This bracket doesn't replace or include the spring itself — if the spring is stretched, rusted, or broken, it should be replaced separately alongside this guide. Common Problems This Part Fixes Excessive tub movement or vibration, especially noticeable during spin Unusual banging, knocking, or thudding noise from inside the cabinet Washer that vibrates more than it used to, or seems to "walk" across the floor during spin Suspension spring that has come loose, shifted, or disconnected from its mounting point Tub striking the cabinet frame or nearby panels during operation Visible cracking or breakage on the guide/bracket where the spring attaches Noise that has gradually worsened over time as the guide wears Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer suspension spring guide directly replaces the following OEM and cross-reference part numbers: DC61-02432A, AP5581510, 2069491, ASM33826, PD00026723, PS4206750 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This suspension spring guide is compatible with select Samsung washers, and also fits select Kenmore washers built on the Samsung platform, including model numbers such as: Samsung 402-49032012 Samsung 592-49006, 592-49032, 592-49042, 592-49045, 592-49052, 592-49075 Kenmore 40249032012 Note: This is the spring guide/bracket only — it does not include the suspension spring itself. If your spring is stretched, rusted, corroded, or broken, order the correct spring separately in addition to this guide. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine Samsung OEM part — factory-specified bracket geometry and mounting fit Connects the washer's outer frame to the suspension spring, keeping it correctly seated and aligned Resolves "excessive tub movement," "banging or knocking noise," "washer vibrating or walking," and "loose spring" symptoms caused by guide failure Direct drop-in replacement — mounts to the original frame attachment point Simple, tool-light installation Replaces AP5581510, 2069491, and PS4206750 Compatible with a range of Samsung and select Kenmore washers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number DC61-02432A Part Type Washer Suspension Spring Guide / Bracket Condition Genuine OEM Brand Samsung Function Connects and aligns the washer frame to the suspension spring Includes Spring No — bracket/guide only, spring sold separately Quantity 1 spring guide Compatible Brands Samsung, Kenmore Installation Notes ⚠️ Unplug Washer Before Starting Disconnect power at the outlet before beginning. Wear work gloves. Depending on your washer's design, you may need to remove the cabinet or rear access panel to reach the suspension spring and its guide bracket at the top of the tub assembly. Photograph how the old guide and spring are connected to the frame before removing anything, since suspension components are often symmetrical and easy to reverse or mismatch between mounting points. Carefully release the tension on the affected spring — depending on the model, this may involve unhooking the spring from the frame or the tub side first, then removing the old guide from its mounting point on the frame. Install the new DC61-02432A guide in the same position, then reattach the spring, making sure it seats fully and squarely in the new guide. Check any other springs and guides in the suspension system while you're in there, since if one has failed from age or wear, the others are often not far behind. Reassemble any panels you removed, restore power, and run a spin cycle to confirm the excessive movement, vibration, or banging noise has resolved. Tools needed: screwdriver (model-dependent access), pliers (helpful for spring tension), work gloves. Frequently Asked Questions My washer bangs loudly during spin. Is this the part I need? It's a strong possibility, especially if the banging has developed gradually or seems to come from inside the cabinet near the tub. This guide keeps the suspension spring seated and aligned; when it cracks or wears out, the spring can shift out of position, letting the tub move more than it should and strike nearby components. Before ordering, it's worth opening up the access panel if you're comfortable doing so, to visually confirm whether a spring has come loose or a guide bracket looks cracked or broken. Does this part include the suspension spring? No — this is the guide/bracket only, which connects the frame to the spring. If your suspension spring itself is stretched, rusted, corroded, or snapped, you'll need to order the correct spring for your model separately in addition to this guide. Should I replace just one guide, or check the others too? It's worth inspecting the other suspension springs and guides while you have access, since they're typically all the same age and subject to the same wear. If one has failed, the others may not be far behind, and replacing them together can save you from repeating this repair again soon after. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Samsung to factory specifications — guaranteed fit, materials, and performance. It matches the original bracket geometry and mounting fit of the suspension spring guide originally installed in your washer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

4681EA2001T Genuine OEM LG Washer Drain Pump Motor The 4681EA2001T is a genuine LG OEM drain pump motor for LG and Kenmore front-load washers, and also fits washer/dryer combo units. This motor is responsible for removing water from the washer at the end of the wash and spin cycles, expelling it through the drain hose so the machine can move on to the next stage of the cycle. This part is the motor only — you'll reuse your existing pump housing. It includes the pump impeller, which is not sold separately. Rated 120V-127V, 60Hz, 85W, 1.4A, with a flow rate of 45L per minute. Measures approximately 6.57" x 4.29" x 3.5". As of April 2025, the design of this drain pump motor changed to a gray housing, replacing the earlier black housing — this is expected and doesn't affect fit or function. Common failure causes include a worn or seized motor and general electrical wear. Symptoms of a failing drain pump motor include the washer not draining, unusual noise during the drain cycle, an OE error code, or leaking near the pump if the motor fails while still under load. It directly replaces 4681EA2001D, 4681EA2001U, 4681EA2001N, 4681EA1007G, 4681EA1007D, LP2001T, AP5328388, 2003273, 1468049, DP040-038, EAP3523278, EAP3579318, and 5214FR4006L. Quick Answer The 4681EA2001T Genuine OEM LG Washer Drain Pump Motor fixes LG and Kenmore front-load washers (and washer/dryer combos) that aren't draining, are making unusual noise during the drain cycle, or are showing an OE error code. 120V-127V, 60Hz, 85W, 1.4A, 45L/min. Replaces 4681EA2001D, 4681EA2001U, 4681EA2001N, 4681EA1007G, 4681EA1007D, LP2001T, AP5328388, 2003273, 1468049, DP040-038, EAP3523278, EAP3579318, 5214FR4006L. This is the motor only — reuse your existing pump housing when installing. As of April 2025, the new housing color is gray instead of the older black; this is a normal design change and not a compatibility issue. Common Problems This Part Fixes Washer not draining — standing water left in the tub after a cycle Unusual noise during the drain cycle OE error code displayed on the control panel Washer taking longer than normal to drain Leaking near the pump area Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer drain pump motor directly replaces the following OEM and cross-reference part numbers: 4681EA2001T, 4681EA1007G, 2003273, 4681EA1007D, 4681EA2001D, 4681EA2001N, 4681EA2001U, DP040-038, ALG51292, AH3579318, EA3579318, PD00001722, EAP3579318, AP5328388, PS3579318 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drain pump motor is compatible with select LG front-load washers, and also fits select Kenmore Elite washers built on the LG platform, and washer/dryer combo units, including model numbers such as WM2101HW, WM3270CW, WM3431HS, WM3770HVA, WM3001HWA, WM8000HVA, WM8000HWA, WM2550HRCA, WM2550HWCA, GCW1069CS, WM3550HWCA, WM3070HRA, WM4070HVA, WM3070HWA, WM2350HRC, WM3360HVCA, WM2350HWC, GCW1069QS, WM2650HRA, WM3360HRCA, WM3360HWCA, WM3150HVC, WM2650HWA, WM2655HVA, WM3885HCCA, WM3150HWC, WM3885HWCA, WM2250CW, WM2450HRA, WM3987HW, WM3470HVA, WM3470HWA, LSWF388HVS, WM3550HVCA, WM2455HG, WM2277HB, WM2487HRMA, and Kenmore 79641072310. Note: Always verify your full model number before ordering, since LG uses several different drain pump designs across its washer lineup. Contact our support team with your model number if you're unsure. Key Features Genuine LG OEM part — factory-specified motor design and impeller Pumps wastewater out of the tub through the drain hose Resolves "not draining," "unusual noise during drain," and "OE error code" symptoms caused by motor failure Includes pump impeller (not sold separately) Reuses your existing pump housing — motor only Rated 120V-127V, 60Hz, 85W, 1.4A, 45L/min flow rate Direct drop-in replacement matching the original mounting and connections Replaces 4681EA2001D, 4681EA2001U, 4681EA2001N, 4681EA1007G, 4681EA1007D, LP2001T, AP5328388, 2003273, 1468049, DP040-038, EAP3523278, EAP3579318, and 5214FR4006L Compatible with LG and Kenmore front-load washers and washer/dryer combo units Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number 4681EA2001T Part Type Washer Drain Pump Motor Condition Genuine OEM Brand LG Application Front-Load Washers, Washer/Dryer Combos Voltage 120V-127V Frequency 60 Hz Wattage 85 W Amperage 1.4 A Flow Rate 45 L/min Dimensions Approx. 6.57" x 4.29" x 3.5" Housing Not included — reuse existing pump housing Housing Color (as of April 2025) Gray (previously black) Repair Difficulty Medium — 30 to 60 minutes Quantity 1 drain pump motor Compatible Brands LG, Kenmore Installation Notes ⚠️ Unplug Washer And Shut Off Water Supply Before Starting — Have Towels Ready For Draining Water Disconnect power at the outlet or shut off the circuit breaker, and shut off the water supply before beginning. Wear work gloves. Lay towels down in front of the washer before starting, and have a pail ready. Remove the detergent drawer and check the drain filter (bottom lower left panel door) to confirm it's clean and the drain line isn't blocked before assuming the motor is at fault. Many customers find it easier to access the pump from underneath by carefully laying the washer on its back — be prepared for a significant amount of additional water to drain out onto the floor once you do this, so keep towels close by. With access to the pump, disconnect the electrical connector from the old motor and separate the motor from the pump housing, which you'll reuse with the new motor. Attach the new 4681EA2001T motor to your existing pump housing, transferring the impeller setup as needed. Reconnect the electrical connector fully. Stand the washer back upright, reinstall the detergent drawer, and reconnect the water supply and power. Test the new pump to confirm it drains properly before considering the repair complete. Tools needed: Phillips screwdriver, locking pliers, needle nose pliers, small flathead screwdriver, towels, work gloves. Frequently Asked Questions My washer shows an OE error code and isn't draining. Is this the part I need? Likely yes. An OE error code on LG washers is commonly tied to a drain issue, and a bad drain pump motor is one of the most frequent causes. Before replacing the motor, it's worth checking that the drain filter and coin trap (if your model has one) are clean and that the drain line itself isn't blocked, since those are simpler and cheaper things to rule out first. Does this come with the pump housing? No, this is the motor only, and it includes the pump impeller, which isn't sold separately. You'll reuse your existing pump housing during installation rather than replacing it as part of this repair. The new motor's housing looks a different color than I expected. Did I get the wrong part? No, this is expected. As of April 2025, LG changed the design of this drain pump motor to use a gray housing in place of the earlier black housing. This is a normal manufacturing update and doesn't affect fit or function. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by LG to factory specifications — guaranteed fit, materials, and performance. It matches the original motor design, impeller, and electrical rating of the drain pump motor originally installed in your washer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 5304516132 Washer Drive Belt – Compatible with Frigidaire, Electrolux, and Kenmore Washers Product Description Keep your washer spinning smoothly with the XPARTCO 5304516132 Washer Drive Belt. This high-quality aftermarket replacement transfers power from the motor to the washer drum, enabling proper agitation and spin speed. A worn, stretched, or broken belt can cause slow spinning, loud noises, or the drum not turning at all. Replacing it with this durable XPARTCO belt restores reliable performance and efficient wash cycles. Replaces Part Numbers 5304516132, 12638000001161, 7PJE607, PD00055739, EAP12585162, 4839724, AP6339955, PS12585162. Compatibility This replacement drive belt fits select Frigidaire, Electrolux, and Kenmore front-load washers. Example compatible models include (but are not limited to): Frigidaire FAFW3801LW, Electrolux EWFLS70JSS0, and Kenmore 417.41122310. Always verify your washer's model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM fit and performance at a lower cost ⚙️ Restores Drum Motion – Ensures proper spinning, agitation, and wash performance 💪 Durable Construction – Made with reinforced rubber for long-lasting tension 🛠️ Easy Installation – Designed for quick DIY replacement 🛡️ Fixes Common Issues – Solves slow spinning, no spin, squealing noises, or drum not turning 📐 Product Specification Part Number: 5304516132 Component Type: Washer Drive Belt Material: Reinforced rubber with tension-resistant cord Dimensions: Exact OEM-equivalent sizing for proper tension Mounting: Wraps around motor pulley and drum pulley Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver (depending on model) ⚠️ Safety First: Always unplug the washer before servicing to avoid electrical shock. Steps: Unplug the washer and remove the rear access panel. Locate the old drive belt and remove it from the motor and drum pulleys. Position the new XPARTCO 5304516132 belt around the drum pulley first. Stretch the belt onto the motor pulley while rotating the drum. Reinstall the back panel, restore power, and test wash/spin cycles. ⏱️ Time Required: 10–20 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Restore smooth washer performance — Add to Cart Now for a dependable, affordable repair!

Read more less

ERP 383EER3001G Washer Shock Absorber  Fits Specific LG, Kenmore Front Load Washer Models. Replaces Part Numbers: 383EER3001G, 383EER3001A, 383EER3001F, 383EER3001H, 383EER3001K, 383EER3001L, AH3522311, EA3522311, AP4437743, PS3522311.    California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

WP3347288 Washer Lower Agitator  Fits Specific Top Load Washer Models. Replaces Part Number: WP3347288, 3347288, 3348245, 3352107, 519233, AP6008022, PS11741151. Description: The Lower Agitator is an OEM part designed for select Kenmore, Whirlpool top-loading washing machines. It sits at the bottom of the wash tub and plays a key agitation role during cycles. This is the bottom part of the agitator assembly.

Read more less