ERP 3406108 Dryer Door Switch
Replaces Part Numbers: WP3406108, 3406108, PS11741702, AP6008562
Description: This Door Switch is a replacement part for select Whirlpool dryer models. It is responsible for detecting whether the dryer door is open or closed. When the door is closed, the switch allows the dryer to operate. Conversely, if the door is open, the switch interrupts the electrical circuit to prevent the dryer from running, ensuring safety during use.
Fits Models: LTE5243DQ1 , LTE5243DQ2 , LTE5243DQ3 , LTE5243DQ4 , LTE5243DQ5 , LTE5243DQ6 , LTE5243DQ7 , LTE5243DQ8 , LTE5243DQ9 , LTE5243DQA , LTE5243DQB , LTE5243DT2 , LTE5243DT3 , LTE5243DT4 , LTE5243DT5 , LTE5243DT6 , LTE5243DT7 , LTE5243DZ1 , LTE5243DZ2 , LTG5243DQ1 , LTG5243DQ2 , LTG5243DQ3 , LTG5243DQ4 , LTG5243DQ5 , LTG5243DQ6 , LTG5243DQ7 , LTG5243DQ8 , LTG5243DQ9 , LTG5243DQA , LTG5243DQB , LTG5243DQC , LTG5243DT2 , LTG5243DT3 , LTG5243DT4 , LTG5243DT5 , LTG5243DT6 , LTG5243DT7 , LTG5243DT8 , LTG5243DZ1 , LTG5243DZ2 , WET4024EW0 , YLTE5243DQ2 , YLTE5243DQ3 , YLTE5243DQ4 , YLTE5243DQ5 , YLTE5243DQ6 , YLTE5243DQ7 , YLTE5243DQ8 , YLTE5243DQ9 , YLTE5243DQA , YLTE5243DQB , YWET4024EW0.
This is an aftermarket part that can be used as a replacement for the OEM part.
00770657 Genuine OEM Bosch Dishwasher Silverware / Cutlery Drawer
The 00770657 is a genuine Bosch OEM cutlery drawer — a dedicated third-rack silverware caddy that sits in the upper interior of the dishwasher tub, above the top rack, on select Bosch dishwashers equipped with a third rack add-on compartment. Rather than loading silverware into a basket down in the lower rack, this drawer holds forks, spoons, and knives flat in their own dedicated level, laid out individually with room around each piece so water and detergent can reach every surface. It rides on durable rollers along rails built into the tub, sliding smoothly in and out for loading and unloading, and its position at the top of the tub gives it a clear, unobstructed line to the upper spray arm for targeted cleaning.
The tray and support grid inside the drawer are open enough to let water flow freely through while still keeping utensils separated and organized. Because it's a lightweight tray sitting in a hot, wet, chemically active environment for years, common failure points include a metal frame that rusts through and eventually collapses under its own weight, plastic that becomes brittle or begins visibly disappearing from years of heat exposure, and dividers that crack or break, letting silverware jumble together. It directly replaces AP5788109, 00689507, 3279853, and PS8747441. As a genuine OEM part, the 00770657 is manufactured by Bosch to factory specifications — guaranteed fit, materials, and performance.
Quick Answer
The 00770657 Genuine OEM Bosch Dishwasher Silverware / Cutlery Drawer fixes Bosch (and compatible Thermador, Gaggenau, and select Kenmore) dishwashers with a third-rack cutlery drawer that has rusted through, has cracked or broken dividers, has become gummy or sticky and won't slide smoothly, or has cracks exposing silverware to the heating element below. Rides on rollers for smooth in-and-out extension. Replaces AP5788109, 00689507, 3279853, PS8747441. This is the roller-equipped cutlery drawer — a similar-looking companion part, 00770656, is a different drawer design without rollers, so double-check which one your dishwasher uses.
Common Problems This Part Fixes
Metal frame of the cutlery drawer rusted through or visibly corroding
Drawer frame collapsing or sagging under the weight of silverware
Missing or broken dividers letting silverware commingle instead of staying separated
Drawer glides that have become gummy or sticky from food residue buildup, obstructing smooth movement
Cracks or holes in the drawer exposing silverware to direct contact with the heating element
Plastic that has become brittle, discolored, or is visibly disappearing after years of heat exposure
Silverware not getting fully clean due to poor spray coverage from a warped or damaged drawer
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This dishwasher cutlery drawer directly replaces the following OEM and cross-reference part numbers:
00770657, AP5788109, 00689507, 3279853, ABS12031, EAP8747441, PD00043732, PS8747441
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This cutlery drawer is compatible with select Bosch dishwashers equipped with a third rack add-on compartment, and is also compatible with Thermador, Gaggenau, and select Kenmore dishwashers configured with a triple-rack setup, including model numbers such as:
SHE68T52UC, SHE68T55UC, SHE68T56UC, SHE68TL5UC
SHE863WF5N, SHE863WF6N
SHP65T56UC, SHP65TL2UC
SHV68T53UC, SHV68TL3UC, SHV863WD3N
SHVM63W53N, SHXM63W55N, SHXM63WS5N
Each of these models spans multiple production suffixes (such as /01, /02, /07, and /09) — check your full model and production number for exact confirmation.
Note — check for rollers: This drawer rides on rollers. A similar-looking companion part, 00770656, is a separate cutlery drawer design used on other Bosch/Thermador/Gaggenau models without the roller mechanism. The two are not interchangeable. Check whether your existing drawer slides on visible rollers before ordering, and always verify your full model and production number. Contact our support team with your model number if you're unsure which drawer fits your dishwasher.
Key Features
Genuine Bosch OEM part — factory-specified frame, grid, and roller mechanism
Dedicated third-rack cutlery drawer positioned above the top rack for optimal spray-arm targeting
Resolves "rusted frame," "broken dividers," "sticky glides," and "cracked drawer" symptoms caused by wear and corrosion
Multi-level basket layout keeps silverware separated for full surface exposure to wash spray
Rides smoothly on rollers for easy extension and retraction when loading and unloading
Open tray and support grid design allows water and detergent to flow through freely
Direct drop-in replacement — no tools required, simply slides into place on existing rails
Replaces AP5788109, 00689507, 3279853, and PS8747441
Compatible with Bosch, Thermador, Gaggenau, and select Kenmore third-rack dishwashers
Genuine OEM replacement — guaranteed fit, materials, and performance
Product Specifications
Part Number
00770657
Part Type
Dishwasher Third-Rack Cutlery / Silverware Drawer
Condition
Genuine OEM
Brand
Bosch
Location
Upper interior of the tub, above the top rack
Mounting
Rides on rollers along built-in tub rails
Design
Multi-level basket grid with open tray for water flow
Repair Difficulty
Very Easy — no tools required
Quantity
1 cutlery drawer
Compatible Brands
Bosch, Thermador, Gaggenau, select Kenmore
Installation Notes
This is one of the simplest repairs in the entire dishwasher — no tools, no wiring, and no water lines to disconnect. Open the dishwasher door fully. Locate the existing cutlery drawer at the top of the tub, above the upper rack, and slide it forward and out along its rails until it clears the cabinet. Line up the new 00770657 drawer with the same rollers and rails, and slide it in until it seats fully at the back of the tub. Close the door and run a cycle to confirm the drawer sits securely and doesn't rattle or shift during operation.
Frequently Asked Questions
Does my drawer use rollers, or is it the other style?
Slide your existing drawer out partway and look underneath or along the sides — this 00770657 drawer rides on visible roller wheels along the tub rails. If your drawer instead has a simpler glide track with no rollers, you likely have the companion part, 00770656, which is a different design used on other models. The two aren't interchangeable, so it's worth confirming before ordering.
My drawer's metal frame has rusted through. Is that just cosmetic, or should I replace it?
It's worth replacing rather than living with it. Once the metal frame starts rusting through, it typically continues to weaken and can eventually collapse under the weight of loaded silverware, sometimes suddenly. Customers who've dealt with this describe the original frame rusting to the point of failure over time — replacing it before it fully gives out avoids a mid-cycle collapse and keeps your utensils properly organized and exposed to the wash spray.
Do I need any tools to install this?
No. This is a genuinely tool-free repair — slide the old drawer out along its rails, then slide the new one in until it seats. Customers consistently describe this as one of the easiest dishwasher parts to swap.
I see cracks or holes in my drawer near the bottom. Is that a safety concern?
It can be, depending on where the damage is. If cracks or holes are positioned where silverware could shift down and make direct contact with the dishwasher's heating element, that's worth addressing rather than ignoring, since it can affect both the cleaning process and the condition of your utensils over repeated cycles. Replacing a cracked or holed drawer resolves this.
Is this an OEM or aftermarket part?
This is a genuine OEM part, manufactured by Bosch to factory specifications — guaranteed fit, materials, and performance. It matches the original roller mechanism, basket grid layout, and dimensions of the cutlery drawer originally installed in your third-rack-equipped Bosch, Thermador, Gaggenau, or compatible Kenmore dishwasher.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
XPARTCO 4970FR2084Z Washer Suspension Spring
The XPARTCO 4970FR2084Z is an aftermarket replacement suspension hinge spring for LG and Kenmore front-load washers. The suspension springs support and stabilize the outer tub during wash and spin cycles and help it stay steady through unbalanced loads. When a spring is broken, snapped, or stretched, the washer may make a loud noise during spin, vibrate heavily, or stop spinning.
This is a direct-fit aftermarket replacement for the original LG spring. A broken spring can let the drum drop and damage the shocks, dampers, and door seal, so inspect those parts while the washer is open.
Quick Answer
The XPARTCO 4970FR2084Z Suspension Spring fixes an LG or Kenmore front-load washer that is loud or shakes badly during spin, stops spinning, or has a drum that has dropped because a suspension spring is broken or stretched. Classic symptom: a loud banging or grinding noise on spin, as if something snapped inside the washer.
Common Problems This Part Fixes
Loud drum noise during the spin cycle
Excessive vibration or shaking on spin
Washer stops spinning or stops mid-cycle
Drum looks lowered, or the front door seal is pushed forward
Visibly broken, snapped, or stretched spring
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This suspension spring directly replaces the following part numbers:
4970FR2084Z, MHY62964802, AGF75223050, MHY57694605, MHY62964801, ALG51959, AP4998892, AH3524578, EA3524578, OEM14996685, PD00028343, PS3524578
These numbers span several generations of LG's own part numbering for this spring as washer models were updated. Confirm against your washer's parts diagram, or contact our support team, if your model calls out a different number.
Compatibility
This suspension spring is listed for LG and Kenmore front-load washers, including these examples:
LG WM3470HWA, WM3360HWCA, WM3700HVA, WM3770HVA, WM4370HWA, WM5000HWA
LG WM2601HW, WM2801HWA, WM2901HVA, WM3001HWA, WM3875HWCA
Kenmore 79641172212, 79641182311
Note: The models above are a sample of more than 100 listed models, not a full list. Washers use more than one suspension spring, and customers often replace the springs on both sides together, so check how many your model uses. Confirm your model number against your parts diagram, or contact our support team to verify fit before ordering.
Key Features
Direct-fit aftermarket suspension hinge spring for LG and Kenmore front-load washers
Supports and stabilizes the outer tub during wash and spin cycles
Resolves loud spin noise and vibration caused by a broken or stretched spring
Fits a long list of LG and Kenmore front-load models
Product Specifications
Part Number
XP4970FR2084Z
OEM Part Number
4970FR2084Z
Part Type
Washer Suspension Hinge Spring
Condition
Aftermarket Replacement
Application
LG & Kenmore Front-Load Washers
Installation Notes
⚠️ Unplug Power Before Installing Unplug the washer and turn off the water supply before beginning, and wear work gloves. Follow your model's service guide to reach the springs, which usually means removing the top and front panels. The drum is heavy, so have a second person lift it, or use a rope loop, while you hook the new spring, which customers say is the hardest step. Check the shocks, dampers, hoses, and door seal while you are in there, since a dropped drum can damage them. Reassemble, then run a spin cycle and check the washer is steady.
Frequently Asked Questions
My washer is very loud on spin. Is this the part I need?
A broken or stretched suspension spring is a common cause of loud spin noise and heavy vibration, especially if it sounded like something snapped. Check the springs, shocks, and dampers for damage.
Should I replace all the springs?
Many customers replace the springs on both sides together, since an old spring may stretch or fail soon after. Check your parts diagram for how many your model uses.
Is this an easy repair?
Retailers rate it easy to moderate, with customers reporting from under 15 minutes to 2 hours. Hooking the new spring while holding up the drum is the hardest part, so a helper makes it easier.
Will this fit my washer?
It is listed for many LG and Kenmore front-load washers, but the model list above is only a sample. Check your model number against your parts diagram, or contact our support team and we'll verify it before you order.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
XPARTCO W10195416 Dishwasher Lower Rack Wheel Replaces W10195416V
The XPARTCO W10195416 is an aftermarket replacement lower dishrack wheel assembly for Whirlpool dishwashers, and also fits select Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models. This assembly attaches directly to the lower dishrack and lets it slide in and out of the dishwasher smoothly during loading and unloading.
This is a current, superseding part number — it replaces the earlier W10195416V designation. Finished in gray, made of heat-resistant ABS plastic without BPA, rated for temperatures up to 300°F. The wheel measures approximately 1.59" in diameter, with an overall assembly height of about 2.83" and a footprint of roughly 3" x 6". Over time, normal wear and tear can crack or break the wheel or its mounting caps. Symptoms of a failing wheel assembly include the rack becoming difficult to slide, jerky or uneven wheel movement, noisy or screeching sounds when moving the rack, or in more advanced cases, dishes not cleaning properly because the rack isn't positioned correctly. It directly replaces W10195416V, W10195416, W10195416VP, 1872127, 4245021, AP5983730, AWP1252597, EAP11722152, PD00024134, PS11722152
Quick Answer
The XPARTCO W10195416 Dishwasher Lower Rack Wheel fixes Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore dishwashers where the lower rack is hard to slide, moves jerkily, makes noise, or won't clean dishes properly because it's out of position. Gray, ABS plastic, ~1.59" wheel diameter. Replaces W10195416V, W10195416, W10195416VP, 1872127, 4245021, AP5983730, AWP1252597, EAP11722152, PD00024134, PS11722152. This wheel snaps on and off — no tools are typically required for installation.
Common Problems This Part Fixes
Lower rack difficult to slide in or out
Jerky or uneven wheel movement
Noisy or screeching sound when moving the rack
Dishes not cleaning properly due to a misaligned rack
Broken or cracked wheel visible on the rack
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This dishwasher lower rack wheel directly replaces the following OEM and cross-reference part numbers:
W10195416V, W10195416, W10195416VP, 1872127, 4245021, AP5983730, AWP1252597, EAP11722152, PD00024134, PS11722152
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This lower rack wheel is compatible with select Whirlpool dishwashers, and also fits select Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore dishwashers built on the Whirlpool platform, including model numbers such as WDT780SAEM1, MDB4949SDM2, and Kenmore 66513222N410, 66513222N411, 66513222N412, 66513222N413, 66513223N410, 66513223N411, 66513293K116, and 66513299K110.
Note: This wheel is a different part from the similarly-numbered W10195417 and W10195420 wheels used on other models. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which wheel your dishwasher needs.
Key Features
Aftermarket replacement wheel assembly — factory-equivalent wheel and mount design
Lets the lower dishrack slide in and out of the dishwasher smoothly
Resolves "rack hard to slide," "jerky movement," "noisy operation," and "dishes not cleaning properly" symptoms
Superseding part number — current replacement for the earlier W10195416V designation
Gray, heat-resistant ABS plastic without BPA, rated up to 300°F
Approximately 1.59" wheel diameter, 2.83" assembly height, ~3" x 6" footprint
Snap-on/snap-off installation — no tools typically required
Replaces W10195416V, W10195416, W10195416VP, 1872127, 4245021, AP5983730, AWP1252597, EAP11722152, PD00024134, PS11722152
Compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore dishwashers
Aftermarket replacement built to OEM-equivalent quality standards
Product Specifications
Part Number
W10195416
OEM Part Number
W10195416V
Part Type
Dishwasher Lower Rack Wheel Assembly
Condition
Aftermarket Replacement
Brand
Whirlpool
Color
Gray
Material
ABS plastic (BPA-free)
Heat Resistance
Up to 300°F
Wheel Diameter
Approx. 1.59"
Assembly Height
Approx. 2.83"
Overall Footprint
Approx. 3" x 6"
Supersedes
W10195416V
Repair Difficulty
Very Easy — snap-on, no tools required
Quantity
1 wheel assembly
Compatible Brands
Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore
Installation Notes
⚠️ Unplug Dishwasher Before Starting Disconnect power to the dishwasher before beginning. Open the dishwasher door and pull out the lower dishrack fully. Locate the old wheel assembly and push the tab from both sides — it should pop out of the rack. Take the new W10195416 wheel assembly and position it on the rack, making sure the caps overlap the wire from the inside before clipping it into place by pushing on the wheel until it snaps securely. Repeat for any other worn wheels on the rack. Slide the rack back into the dishwasher and test it by pulling it in and out to confirm smooth, quiet movement. Tools needed: none typically required.
Frequently Asked Questions
My dishwasher rack is hard to slide. Is this the part I need?
Yes, this is the most common symptom of a worn or broken lower rack wheel. Since this wheel is what lets the rack roll smoothly in and out of the dishwasher, a cracked or damaged wheel can make the rack feel stiff, jerky, or difficult to move.
Is this a difficult repair?
No, this is one of the simplest dishwasher repairs. One customer described it as "an easy fix" — the old wheel snaps off, and the new one snaps right on, typically without needing any tools.
My old part number is W10195416V. Is this the same thing?
Yes, W10195416 is the current part number and supersedes the earlier W10195416V designation. If your old wheel's number matches either of these, this is the correct current part to order.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the wheel design, mounting caps, and dimensions of the original W10195416V lower rack wheel used in compatible Whirlpool, Maytag, KitchenAid, and related dishwashers.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
00622058 Dishwasher Genuine OEM Water Valve
Fits Specific Bosch Dishwasher Models
Description: This dishwasher Water Inlet Valve is a Genuine OEM part for specific Bosch dishwasher models. This component is responsible for controlling the flow of water into the dishwasher. It operates via electrical signals from the dishwasher's control board, opening to allow water to enter during the fill cycle and closing to prevent water from entering during other cycles.
✅ Key Features:
Genuine OEM Part for Bosch #00622058
120V, 60Hz single solenoid valve
Includes mounting bracket and hose connection port
Durable thermoplastic construction
🔁 Replaces Part Numbers:
00622058, 1999956, 622058, AH3491417, AP4927070, EA3491417, PS3491417, PS8728724.
🔧 Fixes These Common Symptoms:
Dishwasher not filling with water
Low or slow water flow
Water inlet error codes
Humming or clicking without water intake
Leaking around the valve area
🧰 Compatible With:
✔️ Bosch✔️ Thermador✔️ Gaggenau✔️ Siemens(Check your model number or contact us for assistance.)
✅ Affordable aftermarket solution
✅ Always Fast and Free U.S. shipping
✅ Backed by helpful support and easy returns
✅ Trusted by DIYers and appliance techs
🛒 Restore your dishwasher’s performance — order the 00622058 water inlet valve today from Parts-O-Matic.com, and get it delivered fast and free.
WR2X7054CM Dishwasher / Refrigerator Push-on Nut
Push on retainer clip.
Used on GE dishwashers and refrigerators.
Replaces Part Numbers:WR2X7054, WD02X0429, WD2X429, WR02X7054, AH298353, EA298353, AP2059046, PS298353.
This is an aftermarket part that can be used as a replacement for the OEM part.
California Residents only
WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov
XPARTCO 279973 Dryer Thermostat Kit
The XPARTCO 279973 is an aftermarket replacement dryer thermostat and thermal cut-off kit compatible with a wide range of Whirlpool-family electric dryers including Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Inglis, Roper, and Admiral. The kit contains two components — the high-limit thermostat (L295-80F) and the thermal cut-off fuse — both located on the heating element housing. Together they protect the dryer's heating element from overheating: the high-limit thermostat monitors element temperature and cuts power if it exceeds safe levels, then resets when cooled. The thermal cut-off fuse is a backup one-time device that permanently opens the circuit if the thermostat fails to protect the element.
Both parts are mounted on the side of the heating element housing and can be accessed through the dryer's back panel. The thermal cut-off fuse is a non-resettable one-time device — once it opens, it must be replaced. The 279973 kit includes both parts, an instruction sheet, and hardware. It directly replaces 3391913, 3404151, 3404152, 3977395, 8318314, 897710, 279973VP, AP3094323, and several additional cross-reference numbers. Note: this kit is for electric dryers only. Installs in 20–30 minutes with basic hand tools.
Quick Answer
The XPARTCO 279973 Dryer Thermostat Kit fixes Whirlpool-family electric dryers with no heat, overheating, or a dryer that shuts off too early. Kit includes the L295-80F high-limit thermostat (auto-reset, opens at 295°F) and the thermal cut-off fuse (352°F, one-time). Both mount on the heating element housing. Electric dryers only. Replaces 3391913, 3404151, 8318314, 897710, AP3094323. Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Inglis, Roper, and Admiral.
Common Problems This Kit Fixes
Dryer produces no heat — thermal cut-off fuse or high-limit thermostat has failed
Dryer overheats — clothes or drum too hot at the end of a cycle
Dryer shuts off early before clothes are dry
Dryer takes multiple cycles or very long time to dry clothes
Repeated no-heat failures — underlying overheating condition affecting the element housing components
Dryer tumbles normally but produces no heat at all
What's in the Kit
Part 1 of 2
High-Limit Thermostat (L295-80F)
Opens at 295°F — cuts power to the heating element if temperature exceeds safe levels · Auto-resets when cooled · Located on the heating element housing · Should show closed continuity (near-zero resistance) at room temperature
Part 2 of 2
Thermal Cut-Off Fuse (352°F)
Opens at 352°F — one-time backup safety device on the heating element housing · Permanently interrupts power to the heating element if the high-limit thermostat fails to protect it · Cannot be reset — must be replaced if blown · Should show closed continuity at room temperature when working
Replaces Part Numbers
This thermostat kit directly replaces the following OEM and cross-reference part numbers:
279973, 279973VP, 3391913, 3404151, 3404152, 3977395, 8318314, 897710, ER279973, PD00002626, EAP334387, AWP39286, AH334387, AP3094323, EA334387, PS334387.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This thermostat kit is compatible with select electric dryers only from the following brands:
Whirlpool electric dryers (Duet, Cabrio, and standard series)
Kenmore / Sears electric dryers (Whirlpool-built models)
Maytag electric dryers
KitchenAid electric dryers
Amana electric dryers
Inglis electric dryers
Roper electric dryers
Admiral electric dryers
Important: This kit is for electric dryers only. Gas dryers use a different burner assembly and require a different thermostat kit (XP6974 for Whirlpool-family gas dryers). Always verify your dryer type and model number before ordering. Also: if the thermal cut-off fuse has blown, always check for a clogged exhaust vent before replacing — a blocked vent is the most common root cause of overheating and repeated fuse failures.
Key Features
2-part kit — high-limit thermostat and thermal cut-off fuse, both on the heating element housing
High-limit thermostat (L295-80F) — opens at 295°F to cut element power, auto-resets when cooled
Thermal cut-off fuse (352°F) — one-time backup safety device; permanently opens if thermostat fails to protect the element
Both parts located on the heating element housing — accessible from the dryer back panel
Replacing both together ensures complete thermal protection is restored on the element housing
Replaces 3391913, 3404151, 8318314, 897710, AP3094323, and over 10 additional cross-reference numbers
Electric dryers only — not for gas dryer models
Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Inglis, Roper, and Admiral electric dryers
Aftermarket replacement built to OEM-equivalent quality standards
Installs in 20–30 minutes with basic hand tools
Product Specifications
Kit Part Number
279973
Condition
Aftermarket Replacement
Application
Electric Dryers Only
Kit Includes
1x High-Limit Thermostat (L295-80F), 1x Thermal Cut-Off Fuse (352°F), hardware, instruction sheet
High-Limit Thermostat Rating
L295-80F — opens at 295°F, resets at 215°F — auto-resets
Thermal Cut-Off Fuse Trip Temp
352°F — one-time, non-resettable
Location
Heating element housing (both parts)
Compatible Brands
Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Inglis, Roper, Admiral
Installation Notes
⚠️ Unplug Dryer Before Starting — Electric Dryers Only Disconnect power before beginning. Remove the back panel of the dryer by unscrewing the perimeter screws to expose the heating element housing. Both the high-limit thermostat and thermal cut-off fuse are mounted on the side of the heating element housing — the thermostat is typically the larger component and the thermal cut-off fuse is smaller. Test each component with a multimeter before removing (both should show closed continuity at room temperature; the failed one will read open). Photograph the wiring before disconnecting. Disconnect the wires, remove the mounting screws, and install the new components in the same positions. Reconnect the wires and mounting screws, reinstall the back panel, restore power, and run a test cycle to confirm heat. Tip: Before running the dryer, clean the full length of the exhaust duct — a clogged vent is the most common cause of overheating and a blown thermal cut-off fuse. Tools needed: Phillips screwdriver, 1/4" nut driver, multimeter.
Frequently Asked Questions
What is the difference between the high-limit thermostat and the thermal cut-off fuse in this kit?
The high-limit thermostat (L295-80F) is a resettable safety switch that opens at 295°F to cut power to the heating element and resets automatically when the temperature drops. It is the primary protection against overheating during normal operation. The thermal cut-off fuse is a one-time backup device rated at 352°F — it permanently opens the circuit if the heating element temperature climbs beyond the point the thermostat should have caught. Once the cut-off fuse opens, it must be replaced; it does not reset on its own. If the cut-off fuse has blown, it usually means the high-limit thermostat also failed to do its job and should be replaced at the same time — which is exactly what this kit provides.
How do I test these parts with a multimeter?
Unplug the dryer and remove the back panel to access the heating element housing. Disconnect each component from the wiring and probe both terminals with a multimeter set to continuity or resistance mode. At room temperature, both the high-limit thermostat and the thermal cut-off fuse should show closed continuity (near-zero resistance). Any component that reads open circuit (no continuity) has failed and needs to be replaced. The thermal cut-off fuse reads open even after it cools — it is non-resettable. The high-limit thermostat may read open at room temperature if it has failed internally rather than by an overheat trip.
How is the 279973 kit different from the XP6974 thermostat kit?
The 279973 is a 2-part kit — high-limit thermostat and thermal cut-off fuse — designed specifically for the heating element housing of Whirlpool-family electric dryers. The XP6974 is a 4-part kit — cycling thermostat, thermal fuse, high-limit thermostat, and thermal cut-off — designed for Whirlpool-family gas and electric dryers, covering both the exhaust duct components and the burner/element housing components. If your electric dryer is showing no-heat and you need only the heating element housing components, the 279973 kit covers exactly those two parts. If you want to replace all thermal components in one repair, the XP6974 covers a broader set.
Why does the thermal cut-off fuse keep blowing?
If the thermal cut-off fuse blows repeatedly after replacement, it almost always means there is an underlying overheating condition causing the heating element housing to run hotter than it should. The most common cause is a clogged or restricted exhaust vent — lint accumulation in the duct reduces airflow, trapping heat inside the dryer cabinet and around the element. Other causes include a failed cycling thermostat that is not regulating element temperature correctly, a stuck heating element relay, or a dryer in an enclosed space with inadequate ventilation. Always clean the full exhaust duct and check the cycling thermostat (WP3387134) before replacing the thermal cut-off fuse a second time.
Is this an OEM or aftermarket part?
This is an aftermarket replacement kit built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the temperature ratings and specifications of the original 279973 high-limit thermostat and thermal cut-off fuse kit.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
XPARTCO DC66-00887A Washer Pulsator Cap – Compatible with Samsung Washers
Product Description
Replace your worn or missing washer pulsator cap with the XPARTCO DC66-00887A Washer Pulsator Cap. This high-quality aftermarket replacement protects the central bolt of the pulsator (wash plate) from water intrusion and corrosion. A damaged or missing cap can lead to imbalance, leaks, or noise during spin cycles. Installing this part restores proper drum function and extends the washer’s lifespan.
Replaces Part Numbers
DC66-00887A, PD00038471, EAP11762121, AP6027557, 4814077, PS11762121.
Compatibility
This replacement pulsator cap fits select Samsung top-load washers.
Example compatible models include (but are not limited to):Samsung WA45H7000AW/A2, WA400PJHDWR/AA, WA422PRHDWR/AA
Always verify your washer’s model number before ordering. Contact our support team if you’re unsure.
✅ Key Features
🔄 Aftermarket Replacement – Compatible with Samsung top-load washers
💧 Protective Design – Prevents water from reaching the pulsator bolt
💰 Budget-Friendly Fix – Quality replacement at a lower cost than OEM
🛠️ Simple Installation – Snaps securely into place in seconds
🛡️ Fixes Common Issues – Resolves missing, cracked, or leaking pulsator caps
📐 Product Specification
Part Number: DC66-00887A
Component Type: Washer Pulsator (Wash Plate) Cap
Material: Durable, water-resistant plastic
Mounting: Snap-fit installation, tool-free
Operating Conditions: Designed for residential top-load washers
Compliance: Built to OEM-equivalent quality standards (not OEM)
🛠️ Installation Notes
Tools Needed: None
⚠️ Safety First: Always unplug the washer before performing repairs.
Steps:
Unplug washer and open lid.
Remove any debris around the pulsator area.
Gently pry off the old cap using a flathead screwdriver if needed.
Align and press the new XPARTCO DC66-00887A cap firmly until it clicks.
Confirm a tight seal before restarting the washer.
⏱️ Time Required: 5 minutes
📦 Shop With Confidence
🚚 Free Shipping on All Orders
🛠️ Trusted Appliance Parts Supplier
🔄 30-Day Return Policy
Restore your washer’s performance — Add to Cart Now for a reliable, affordable replacement!
XPARTCO DD31-00016A Dishwasher Drain Pump Motor
The XPARTCO DD31-00016A is an aftermarket replacement BLDC (brushless DC) drain pump motor for Samsung dishwashers. This motor removes water from the dishwasher tub during the drain phase of the cycle — an impeller mechanism pumps water out through the drain hose, running during the draining phase to ensure a constant, steady flow and help prevent clogs.
Weighs approximately 0.50 lbs, with package dimensions of 4.02" x 3.50" x 3.54". Compatible with 120V and 230V systems. Common causes of failure include worn motor bearings, electrical failure, or debris obstructing the impeller. Symptoms of a failing drain pump motor include water not draining from the tub, standing water left after a cycle, unusual noise during the drain phase, or intermittent draining problems that don't happen every cycle. It directly replaces AP5917178, 113121, 4000925, EAP9606350, PS9606350, ASM773863, PD00036475, and 045900194701.
Quick Answer
The XPARTCO DD31-00016A Dishwasher Drain Pump Motor fixes Samsung dishwashers that aren't draining, leave standing water after a cycle, make unusual noise during draining, or have intermittent draining problems. BLDC motor, 120V/230V, ~0.50 lbs. Replaces AP5917178, 113121, 4000925, EAP9606350, PS9606350, ASM773863, PD00036475, 045900194701. When removing the old motor, you'll need to hold a release tab open while twisting the motor counterclockwise at the same time — this two-handed step trips up a lot of first-time installers.
Common Problems This Part Fixes
Dishwasher not draining water from the tub
Standing water left in the tub after a completed cycle
Unusual noise during the drain phase
Intermittent draining problems that don't occur every cycle
Reduced water circulation and cleaning performance
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This dishwasher drain pump motor directly replaces the following OEM and cross-reference part numbers:
DD31-00016A, 113121, 4000925, AP5917178, ASM773863, EAP9606350, PD00036475, PS9606350
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This drain pump motor is compatible with select Samsung dishwashers, including model numbers such as DW80R9950QH/AA, DW80B7070UG/AA, DW80R9950MT/AA, DW80B6061UG/AA, DW80R9950QN/AA, DW80B7070US/AA, DW80B6061US/AA, DW80B7071UG/AA, DW80B6060US/AA, DW80B6060UG/AA, DW80BB7070U1/AA, DW80B7070AP/AA, DW80B7071US/AA, DW80R7061UG/AA, DDW24T999BB/DA, DDW24M999UM/DA, DDW24T998US/DA, DDW24M999US/DA, DW60M9990AP, and DW80B6060UG.
Note: This part is not a replacement for any earlier designation — per Samsung's own listing, DD31-00016A is a new part that doesn't supersede another part number. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure.
Key Features
Aftermarket replacement BLDC (brushless DC) drain pump motor
Resolves "won't drain," "standing water," "unusual noise," and "intermittent draining" symptoms
Impeller mechanism pumps water out through the drain hose to prevent clogs
Compatible with 120V and 230V systems
Direct drop-in replacement matching the original mounting and connections
Replaces AP5917178, 113121, 4000925, EAP9606350, PS9606350, ASM773863, PD00036475, and 045900194701
Compatible with Samsung dishwashers
Aftermarket replacement built to OEM-equivalent quality standards
Typical repair takes 30 to 60 minutes
Product Specifications
Part Number
XPDD31-00016A
OEM Part Number
DD31-00016A
Part Type
Dishwasher Drain Pump Motor (BLDC)
Condition
Aftermarket Replacement
Brand
Samsung
Motor Type
Brushless DC (BLDC)
Voltage Compatibility
120V / 230V
Weight
Approx. 0.50 lbs
Package Dimensions
4.02" x 3.50" x 3.54"
Repair Difficulty
Moderate — 30 to 60 minutes
Quantity
1 drain pump motor
Compatible Brand
Samsung
Installation Notes
⚠️ Unplug Dishwasher And Shut Off Water Supply Before Starting — This Step Needs Two Hands Turn off and unplug the dishwasher for safety, and shut off the water supply before beginning. Wear work gloves. Remove any panels or components blocking access to the motor pump. Disconnect all wiring from the old motor. Removing the old motor requires holding a release tab open while simultaneously twisting the motor counterclockwise — this two-handed step trips up a lot of first-time installers, so take it slowly and make sure the tab stays held open through the full twist. Once free, remove the old motor. Install the new DD31-00016A securely in the same mounting position. Reconnect all wiring according to the original connections. Reinstall any panels or components removed for access. Restore the water supply and power, then run a test cycle to confirm the dishwasher drains completely with no leaks or unusual noise. Tools needed: screwdriver, work gloves.
Frequently Asked Questions
My dishwasher isn't draining. Is this the part I need?
Yes, this is the most direct symptom of a failed drain pump motor. Since this motor is what removes water from the tub during the drain phase, a worn or failed motor can leave standing water behind or prevent the cycle from completing properly.
My dishwasher's drainage problem only happens sometimes. Could this still be the motor?
Yes, this is possible. One customer replaced this exact motor to address an intermittent draining issue, noting it was somewhat of a guess since the problem didn't occur every cycle. Intermittent symptoms can still point to a motor that's beginning to fail rather than one that's failed completely, though it's worth noting the customer wasn't fully certain the replacement resolved their specific issue.
What's the trickiest part of installing this motor?
Removing the old motor requires holding a release tab open while twisting the motor counterclockwise at the same time — a two-handed maneuver that one customer specifically called out as the biggest challenge of the whole repair. Taking it slowly and keeping steady pressure on the tab through the full twist makes this easier.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured to match the motor design, impeller mechanism, and voltage compatibility of the original DD31-00016A drain pump motor used in compatible Samsung dishwashers.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
W11612327 Dishwasher Genuine Circulation Pump
Circulation pump and motor assembly
Replaces Part Numbers: W11612327, W11024423, W10805387, W11521436, AP7194668, PS16744935.
Description: This Pump is a Genuine component for specific Whirlpool dishwasher models. It refers to the water pump component that circulates water throughout the dishwasher during cycles. Common cause of a faulty pump can include normal wear over many uses. The continuous motor operation puts strain on internal seals and impellers. Mineral deposits from hard water can also clog pump parts over time.
XPARTCO 137292700 Dryer Drum Belt
The XPARTCO 137292700 is an aftermarket replacement multi-rib drum belt for Frigidaire stacked laundry center (combination washer/dryer) units, and also fits select Crosley, Electrolux, Gibson, Kelvinator, Kenmore, Tappan, and White Westinghouse combo models. This belt attaches to the motor pulley and spins the drum as the motor rotates, keeping clothes tumbling evenly throughout the drying cycle.
Measures approximately 89-1/2" long and 1/4" wide, with multiple ribs. Over time, this belt naturally dries out, cracks, or breaks from regular use. If your dryer is running but the drum won't turn, there's a good chance the belt has broken. Symptoms of a failing belt include the drum not turning, loud banging noises, or the dryer failing to tumble clothes. It directly replaces 137292700, 134163500, 134503900, 5303283287, 4PH 2273, 4PH2273, AFR14366, AH3408299, AP4565702, EA3408299, EAP3408299, PD00000115, PS3408299.
Quick Answer
The XPARTCO 137292700 Dryer Drum Belt fixes Frigidaire, Crosley, Electrolux, Gibson, Kelvinator, Kenmore, Tappan, and White Westinghouse stacked laundry center units where the drum won't turn, you hear loud banging noises, or the dryer won't tumble clothes. Approximately 89-1/2" long, 1/4" wide, multiple ribs. Replaces 137292700, 134163500, 134503900, 5303283287, 4PH 2273, 4PH2273, AFR14366, AH3408299, AP4565702, EA3408299, EAP3408299, PD00000115, PS3408299. This is a laundry center (stacked combo) belt, distinct from standalone dryer belts — verify your full model number before ordering.
Common Problems This Part Fixes
Drum won't turn even though the motor is running
Loud banging noises during operation
Dryer failing to tumble clothes
Belt visibly cracked, dried out, or broken
Drum stopping mid-cycle
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This dryer drum belt directly replaces the following OEM and cross-reference part numbers:
137292700, 134163500, 134503900, 5303283287, 4PH 2273, 4PH2273, AFR14366, AH3408299, AP4565702, EA3408299, EAP3408299, PD00000115, PS3408299
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This drum belt is compatible with select Frigidaire stacked laundry center units, and also fits select Crosley, Electrolux, Gibson, Kelvinator, Kenmore, Tappan, and White Westinghouse combo units built on the same platform, including model numbers such as WLXG42REW0, FLSE72GCTC, FLSG72GCT1, FLSG72GCT6, LCE852LL1, FLXG52RBS2, FLXG52RBS8, FLXE52RBS9, CLCG900FW0, CLCG900FW1, CLCG900FW2, CLCG900FW3, CLCE900FW0, CLCE900FW1, CLCE900FW2, CLCG500FW0, CLCG500FW1, CLCE600RW0, CLCE500MW1, CLCE500FW2, and CLCE500FW4.
Note: This is a laundry center (stacked washer/dryer combo) belt, distinct from standalone Frigidaire dryer belts. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure.
Key Features
Aftermarket replacement multi-rib drum belt — built to OEM-equivalent specifications
Attaches to the motor pulley to spin the drum for laundry center (combo) units
Resolves "drum won't turn," "loud banging noises," and "won't tumble" symptoms
Approximately 89-1/2" long, 1/4" wide, multiple ribs
Direct drop-in replacement matching the original length and profile
Replaces 137292700, 134163500, 134503900, 5303283287, 4PH 2273, 4PH2273, AFR14366, AH3408299, AP4565702, EA3408299, EAP3408299, PD00000115, PS3408299
Compatible with Frigidaire, Crosley, Electrolux, Gibson, Kelvinator, Kenmore, Tappan, and White Westinghouse laundry center units
Aftermarket replacement built to OEM-equivalent quality standards
Product Specifications
Part Number
XP137292700
OEM Part Number
137292700
Part Type
Laundry Center Multi-Rib Drum Belt
Condition
Aftermarket Replacement
Compatible Brand
Frigidaire
Application
Stacked Washer/Dryer Laundry Centers
Length
Approx. 89-1/2"
Width
1/4"
Ribs
Multiple
Function
Transmits motor rotation to spin the drum
Repair Difficulty
Moderate — laundry center disassembly required
Quantity
1 drum belt
Compatible Brands
Frigidaire, Crosley, Electrolux, Gibson, Kelvinator, Kenmore, Tappan, White Westinghouse
Installation Notes
⚠️ Unplug The Laundry Center Before Starting Disconnect power to the laundry center unit at the outlet before beginning. Wear work gloves. This repair is best approached from the top down: remove the top of the unit first, which gives more room to get the dryer tub out. Remove the two screws from the vented plate on the back of the machine to access and undo the old belt. Since this is a stackable washer/dryer combo, also remove the white plate on the front between the washer and dryer sections for full access. Locate the old belt connecting the motor pulley to the drum and remove it. Fit the new 137292700 belt around the drum and motor pulley in the same path as the old one, making sure it seats correctly and is properly tensioned. Reassemble the front plate, vented back plate, and top of the unit. Restore power and run a test cycle to confirm the drum tumbles smoothly with no banging or unusual noise. Tools needed: putty knife, screwdriver set, work gloves.
Frequently Asked Questions
The motor is running but the drum won't turn. Is this the belt I need?
Yes, this is the classic and most reliable sign of a broken drum belt. If you can hear the motor running normally but the drum itself stays still, the belt has likely dried out and broken, no longer connecting the motor's rotation to the drum.
Is this the same as a standalone Frigidaire dryer belt?
No, this belt is specifically sized and profiled for Frigidaire-style stacked laundry center units, where the washer and dryer are combined into one appliance. It's a different part from standalone Frigidaire dryer belts used on separate dryers. Confirm your unit type and model number before ordering.
Is this a difficult repair?
It's a moderate repair since it involves removing the top of the laundry center unit, the vented back plate, and the front plate between the washer and dryer sections to get full access to the belt. One customer described working from the top down as the easiest approach, since it gives more room to remove the dryer tub.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Frigidaire OEM part, but is manufactured to match the length, width, and rib pattern of the original 137292700 multi-rib drum belt used in compatible Frigidaire, Crosley, Electrolux, Gibson, Kelvinator, Kenmore, Tappan, and White Westinghouse laundry center units.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
