XPARTCO W10209656 Range Surface Igniter – Compatible with Whirlpool, Maytag, KitchenAid, and Kenmore Gas Ranges
Product Description
Restore reliable burner ignition with the XPARTCO W10209656 Range Surface Igniter. This high-quality aftermarket replacement provides the heat needed to ignite gas burners on your cooktop. A weak or failed igniter can cause burners not to light or take too long to ignite. Replacing it with this durable XPARTCO igniter restores instant ignition and safe cooking performance.
Replaces Part Numbers
WPW10209656, W10209656, 1468965, 98008959, 98012193, 98014514, 98014515, 98017561, 98017562, 98017917, W10112313, W10127479, AP6017135, PS11750430.
Compatibility
This replacement surface igniter is compatible with select Whirlpool, Maytag, KitchenAid, and Kenmore gas ranges.
Example compatible models include (but are not limited to): Whirlpool WFG320M0BS3, Maytag MGR6600FZ0, and Kenmore 665.75002100.
Always verify your range’s model number before ordering. Contact our support team if you’re unsure.
✅ Key Features
🔄 Aftermarket Replacement – Compatible with Whirlpool-brand gas ranges
🔥 Reliable Ignition – Provides consistent spark for fast burner lighting
💰 Affordable Solution – Quality alternative to OEM parts at lower cost
🛠️ DIY Friendly – Installs easily with basic hand tools
🛡️ Fixes Common Issues – Solves burners not igniting or clicking without flame
📐 Product Specification
Part Number: W10209656
Component Type: Gas Range Surface Igniter
Material: High-temperature ceramic base and metal electrode
Mounting: Direct-fit replacement for surface burner assembly
Operating Conditions: Designed for standard household gas ranges
Compliance: Built to OEM-equivalent standards (not OEM)
🛠️ Installation Notes
Tools Needed: Phillips screwdriver, nut driver
⚠️ Safety First: Always unplug the range and shut off the gas supply before starting repairs.
Steps:
Disconnect power and shut off gas supply.
Remove burner grates and top panel to access the igniter.
Detach the wire connector and mounting screw from the old igniter.
Install the new XPARTCO W10209656 igniter and reconnect wires.
Reassemble burner components, restore power and gas, and test ignition.
⏱️ Time Required: 15–25 minutes
📦 Shop With Confidence
🚚 Free Shipping on All Orders
🛠️ Trusted Appliance Parts Supplier
🔄 30-Day Return Policy
Enjoy quick, reliable ignition every time — Add to Cart Now for a dependable, budget-friendly repair!
XPARTCO 131763310 Washer Door Striker
The XPARTCO 131763310 is an aftermarket replacement door striker (also called a door strike or door catch) compatible with select Frigidaire, Kenmore, Electrolux, Crosley, Gibson, White-Westinghouse, Kelvinator, and Tappan front-load washers. The door striker is a small plastic tab mounted on the washer door that engages with the door lock assembly on the front of the washer when the door is closed — activating the door switch and allowing the washer to start, fill, and spin. When the striker breaks or wears down, the door will not properly activate the door lock, causing the washer not to start, not to fill, or to display a door-related error code.
Made from durable white plastic, this striker measures approximately 1-1/4" L x 9/16" W x 2-9/16" H with approximately 2 inches between mounting holes (center to center). It directly replaces 131763300, 134456600, 1032664, LP3310, AP3580441, and several additional cross-reference numbers. Sold individually. Installs in under 15 minutes with a Phillips screwdriver.
Quick Answer
The XPARTCO 131763310 Washer Door Striker fixes Frigidaire-platform front-load washers where the door won't activate the door lock, the washer won't start, won't fill, leaks from the door, or shows a door-related error code. White plastic, approx. 1-1/4" L x 9/16" W x 2-9/16" H, ~2" between mounting holes. Sold individually. Phillips screwdriver only — installs in under 15 minutes. Compatible with Frigidaire, Kenmore, Electrolux, Crosley, Gibson, and more.
Common Problems This Part Fixes
Washer door will not properly latch or activate the door lock when closed
Washer will not start — door switch not being triggered by the striker
Washer will not fill with water — door lock not engaged
Washer will not spin — door lock fault preventing cycle completion
Water leaking from the door area due to door not sealing properly
Door-related error codes displayed on compatible models
Broken, cracked, or missing door striker visible on the washer door
Replaces Part Numbers
This door striker directly replaces the following OEM and cross-reference part numbers:
131763310, 134456600, 131763302, 1032664, 131763300, AH890617, EA890617, AP3580441, PS890617, AFR14210, PD00000391, EAP2378364, AP4508273, PS2378364, WH10X10004, 824421, AH269392, EA269392, AP2621447, PS269392.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This door striker is compatible with select front-load washers from the following brands:
Frigidaire front-load washers (ATF, ATFB, BLTF, GLTF, LTF, FTF, FAFW, FRFW series and more)
Kenmore / Sears front-load washers (select Frigidaire-built models)
Electrolux front-load washers (select models)
Crosley front-load washers (CFW, CLCE series)
Gibson front-load washers (GTF series)
White-Westinghouse front-load washers
Kelvinator front-load washers
Tappan front-load washers
Note: The 131763310 (white) and 131763302 (gray) are interchangeable and functionally identical — the only difference is color. Either part will work as a replacement regardless of which color was originally installed.
Key Features
Engages with the door lock assembly to activate the door switch, allowing the washer to start, fill, and run
Critical safety component — washer will not operate without a properly functioning door striker
Durable white plastic construction — strong and wear-resistant for long service life
Dimensions: approx. 1-1/4" L x 9/16" W x 2-9/16" H; ~2" between mounting holes (center to center)
Sold individually — one striker per order
Direct replacement for 131763300, 134456600, 1032664, and LP3310
Compatible with Frigidaire, Kenmore, Electrolux, Crosley, Gibson, White-Westinghouse, Kelvinator, and Tappan washers
Aftermarket replacement built to OEM-equivalent quality standards
Quick DIY repair — installs in under 15 minutes with a Phillips screwdriver only
Product Specifications
Part Number
131763310
Part Type
Washer Door Striker (Door Strike / Door Catch)
Condition
Aftermarket Replacement
Application
Front-Load Washers
Dimensions
Approx. 1-1/4" L x 9/16" W x 2-9/16" H
Mounting Hole Spacing
Approx. 2" center to center
Color
White
Material
Plastic
Sold As
Single striker
Compatible Brands
Frigidaire, Kenmore, Electrolux, Crosley, Gibson, White-Westinghouse, Kelvinator, Tappan
Installation Notes
⚠️ Unplug Washer Before Starting Disconnect power before beginning any repair. Open the washer door and locate the door striker — it is the small plastic tab mounted on the inside of the door, typically near the top or center of the door panel. Remove the two Phillips screws securing the old striker to the door. If the striker is broken, the screws may already be loose or missing. Align the new 131763310 striker with the mounting holes in the door and secure it with the two Phillips screws. Close the door to confirm it clicks firmly into the door lock assembly. Restore power and run a short cycle to verify the washer starts, fills, and runs normally. Tools needed: Phillips screwdriver only.
Frequently Asked Questions
What does the washer door striker do?
The door striker is the small plastic tab on the washer door that engages with the door lock assembly mounted on the front of the washer when the door is closed. As the door closes, the striker pushes into the door lock, activating the door switch — a signal to the control board that the door is securely closed. The washer will not start, fill, or spin unless the door switch is activated by the striker. A broken or worn striker means the door lock is never properly engaged, so the washer appears to be in a constant "door open" state even when the door is physically shut.
What is the difference between the 131763310 and 131763302 door strikers?
Both are Frigidaire-platform door strikers, they are different color and interchangeable. The 131763310 is used on older Frigidaire front-load washer models (ATF, GLTF, FAFW series and others). The 131763302 is a gray color used on newer Frigidaire and Electrolux models. Always compare your existing striker's shape and dimensions to confirm, or contact our support team with your model number.
Should I also replace the door lock assembly when replacing the striker?
Not necessarily — in most cases the striker is the only part that needs replacement. The striker is a small plastic tab that takes repeated impact every time the door is closed, making it the most commonly worn part in the door latch system. The door lock assembly (131763202) is more durable and less prone to failure. Inspect the door lock for any cracks, burn marks, or a latch that does not spring back after pressing — if it appears damaged, replace it as well. If the lock looks intact, the 131763310 striker alone should resolve the issue.
My washer door closes but the washer still won't start — is it the striker?
It may be. If the striker is cracked, worn, or broken, it may appear to engage the door lock but not push far enough into the lock assembly to fully activate the door switch. In other cases, a fully intact striker may not be the cause — the door lock assembly itself (131763202) or the door latch on the frame side may also be the culprit. Visually inspect the striker first — if it is visibly broken, replace it. If it appears intact, the issue may be with the door lock assembly or wiring.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Frigidaire OEM part, but is manufactured from durable plastic to match the dimensions and function of the original 131763310 door striker.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
XPARTCO 00631633 Range Surface Burner Igniter Electrode
The XPARTCO 00631633 is an aftermarket replacement gas range surface burner igniter electrode (also called a spark electrode) compatible with select Bosch, Thermador, and Gaggenau gas ranges and cooktops in the HDI, HGI, NGM, NGMP, HDIP, and HGIP series. The surface burner igniter electrode is the ceramic-tipped spark generator located at each gas burner position on the cooktop. When the burner is turned on, the ignition system sends a high-voltage pulse to the electrode, which generates a spark across the ceramic tip to ignite the gas flowing from the burner. When the electrode cracks, chips, or becomes contaminated with grease or food residue, the burner may fail to light, click continuously without igniting, or spark intermittently.
This replacement electrode is constructed from high-quality ceramic and metal — the ceramic insulator body withstands the thermal cycling of repeated ignition, while the metal spark tip maintains reliable spark gap geometry over time. Sold individually — one electrode per order. It directly replaces AP5950372, 4162041, and PS10057850. Because a gas range typically has four or more burners with individual electrodes, compare your existing electrode's dimensions and mounting configuration before ordering to ensure a correct fit. Installs in minutes — no tools required in most cases.
Quick Answer
The XPARTCO 00631633 Range Surface Burner Igniter Electrode fixes Bosch, Thermador, and Gaggenau gas ranges where a surface burner won't light, clicks repeatedly without igniting, or sparks intermittently. Ceramic and metal construction. Sold individually — one electrode per order. Compatible with Bosch HDI, HGI, NGM, NGMP, HDIP, HGIP series. Replaces AP5950372, 4162041, PS10057850. Compare dimensions to your original before ordering — each burner position uses the same electrode style on compatible models.
Common Problems This Part Fixes
Gas burner will not light when the knob is turned
Burner clicks repeatedly without igniting the gas
Burner sparks intermittently — fires once or twice but does not sustain ignition
Igniter clicks continuously even when the burner knob is in the off position
One burner not lighting while other burners on the same range work normally
Electrode tip visibly cracked, chipped, or heavily contaminated with baked-on grease
Weak or inconsistent spark — arc not reaching the burner port reliably
Replaces Part Numbers
This igniter electrode directly replaces the following OEM and cross-reference part numbers:
00631633, 631633, ABS11789, AP5950372, EAP10057850, PD00044775, PS10057850
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This igniter electrode is compatible with select gas ranges and cooktops from the following brands and series:
Bosch gas ranges — HDI8054U, HDI8056U, HGI8046UC, HGI8054UC, HGI8056UC series
Bosch gas ranges — HDIP054U, HDIP056U, HGIP054UC, HGIP056UC series
Bosch gas cooktops — NGM5055UC, NGM5455UC, NGM5655UC, NGM8055UC, NGM8065UC, NGM8655UC, NGM8665UC, NGMP055UC, NGMP655UC series
Thermador gas ranges and cooktops (select models using the same electrode style)
Gaggenau gas ranges and cooktops (select models using the same electrode style)
Note: Before ordering, compare your existing igniter electrode's physical dimensions and mounting configuration to confirm this electrode is the correct fit for your burner position. Always verify your exact model number. If you are unsure, contact our support team with your model number for confirmation.
Key Features
Ceramic and metal spark electrode — generates the high-voltage spark that ignites the gas burner when the knob is turned
High-quality ceramic insulator body — withstands repeated thermal cycling without cracking under normal use
Durable metal spark tip — maintains reliable spark gap geometry for consistent ignition
Replaces AP5950372, 4162041, and PS10057850
Compatible with Bosch HDI, HGI, NGM, NGMP, HDIP, and HGIP series gas ranges and cooktops
Also compatible with select Thermador and Gaggenau gas ranges and cooktops
Sold individually — one electrode per order; order as many as needed for your burner positions
Aftermarket replacement built to OEM-equivalent quality standards
Quick DIY repair — installs in minutes, no special tools required in most cases
Product Specifications
Part Number
00631633
Also Known As
631633
Part Type
Gas Range Surface Burner Igniter Electrode (Spark Electrode)
Condition
Aftermarket Replacement
Application
Gas Ranges and Cooktops
Material
Ceramic / Metal
Color
White
Sold As
Single electrode — order quantity as needed
Compatible Brands
Bosch, Thermador, Gaggenau
Installation Notes
⚠️ Gas Appliance Safety Warning This part is used in gas ranges. Always turn off the gas supply at the shutoff valve and unplug the range from the electrical outlet before beginning any repair. If you smell gas at any point during or after installation, leave the area immediately and contact your gas utility provider. If you are not confident working on gas appliances, have this part installed by a qualified appliance technician.
⚠️ Unplug Range and Turn Off Gas Before Starting With the range unplugged and gas supply off, remove the cooktop grates and burner caps to access the burner heads. The igniter electrode is the small ceramic component positioned beside each burner head, held in place by a mounting bracket and screw or a snap-in clip depending on the model. Disconnect the single wire connector from the old electrode. Remove the mounting screw and lift the old electrode out. Install the new 00631633 electrode in the same position, secure the mounting screw, and reconnect the wire connector. Replace the burner caps and grates. Restore power and gas supply, then test each burner for reliable ignition. If the burner still does not light after replacing the electrode, inspect the igniter wire and the electronic ignition module. Tools needed: Phillips or Torx screwdriver (for mounting bracket on some models); no tools needed on models with snap-in electrodes.
Frequently Asked Questions
What does the surface burner igniter electrode do?
The igniter electrode is the component that creates the spark to light each gas burner. When you turn a burner knob past the "lite" position, the range's electronic ignition module sends a series of high-voltage pulses through the igniter wiring to the electrode at that burner. The electrode generates a visible spark across its ceramic tip to the grounded burner cap or burner head, and that spark ignites the gas flowing from the burner ports. Each burner position has its own dedicated electrode — failure of one electrode affects only that burner, while other burners on the same range continue to work normally.
My burner clicks constantly even when turned off — is it the electrode?
Constant clicking when a burner is in the off position is almost always caused by moisture or food residue in the igniter system rather than a failed electrode. When liquid boilover or steam gets into the burner cap area or electrode housing, it can cause the ignition module to fire continuously. Remove the burner cap and grate from the affected burner and allow everything to dry thoroughly — an hour in a warm oven (electric only, turned off) can help. Wipe the electrode tip clean with a dry cloth. If clicking persists after the components are completely dry and clean, the electrode or the ignition module may have been damaged by the moisture and needs replacement.
How many electrodes do I need for my Bosch range?
Most Bosch gas ranges have four surface burners, each with its own dedicated igniter electrode — so a full cooktop replacement typically requires four electrodes. This listing is for one electrode. If only one burner is not lighting, you likely only need one replacement. If multiple burners are failing, order one electrode for each affected burner. Because the electrodes on compatible Bosch models use the same part number across all burner positions, one order of multiple quantities covers all positions.
Can I clean the electrode instead of replacing it?
Yes — a contaminated or greasy electrode can often be cleaned successfully rather than replaced. Remove the electrode from the burner area and gently clean the ceramic tip and metal contact with a dry cloth or a soft toothbrush. Do not use water or liquid cleaners directly on the electrode — moisture in the ceramic can cause persistent clicking. If the ceramic body is cracked or the metal tip is corroded or missing, replacement is required. If the ceramic is intact and clean but the spark is still weak or absent, the electrode's spark gap geometry may have changed from thermal expansion and a replacement is the better fix.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Bosch OEM part, but is manufactured from high-quality ceramic and metal to match the dimensions and spark performance of the original 00631633 igniter electrode.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
S48D21 8" Range Surface Element
Product Title
Aftermarket S48D21 8" Range Surface Element - Compatible with Whirlpool, Maytag, Kenmore, Jenn-Air, Amana Electric Ranges
Product Description
Revive your electric range’s cooking performance with the Aftermarket S48D21 8" Range Surface Element from Parts-O-Matic. This high-quality aftermarket burner element replaces the original S48D21, delivering 2100 watts at 240V with a 4-turn coil design for efficient and even heating. Ideal for select Whirlpool, Maytag, Kenmore, Jenn-Air, Amana, and other brand electric ranges, it addresses issues like uneven heating, slow warm-up, or non-functional burners. Enjoy free shipping on all orders at Parts-O-Matic!
Key Features:
✅ Broad Compatibility: Fits select Whirlpool, Maytag, Kenmore, Jenn-Air, Amana, and other electric range models.
🔥 Efficient Heating: 8" diameter, 4-turn coil delivers 2100 watts at 240V for consistent, even cooking.
💰 Cost-Effective Alternative: Aftermarket part offers OEM-equivalent performance at a lower price.
🛠️ Easy Installation: Plug-in design with Y-style bracket; requires no tools and takes 5–10 minutes to install.
🛡️ Fixes Common Issues: Resolves uneven heating, slow warm-up, or burners that fail to heat.
Compatibility:
Compatible with models including but not limited to:
Whirlpool: RF110AXSQ0, RF262LXSB, RF365PXKW0
Maytag: MER4110AAH, MER4120AAQ
Kenmore: 629.4297, 629.60003600 (pre-2004 models)
Jenn-Air: JES9750AAB
Amana: AER5511AAQ
Replaces part numbers: TJ90SP21MA, 14215226, 1938283, 309917, 403782, 404110, 406000, 814154, ERS48D21, SE302, SP21MA, SU214, SU302, TS4D8221, TS4D8221PB, TS4D8221SR, TS4D8221WI, YSP21MA, AP4503257.
Verify compatibility with your appliance brand and model number, please contact Parts-O-Matic support for assistance.
Installation Notes:
Tools Needed: None for standard installation; a flathead screwdriver may help for stubborn connections.
Safety First: Unplug the range before installation to avoid electrical shock.
Steps: Remove the old burner element by gently pulling it from the receptacle, align the Y-style bracket of the new S48D21 element, and plug it into the socket. Ensure the element sits flat in the drip pan. If the burner is not level, adjust the connection bolts to ensure they are parallel and push down gently. Installation takes 5–10 minutes. Note: A slight burning smell during first use is normal due to a protective coating; this will dissipate after 15–20 minutes.
Download our installation guide or watch our YouTube tutorial for step-by-step instructions.
Shop Parts-O-Matic for high-quality aftermarket appliance parts with free shipping on all orders and a 30-day return policy. Restore your range’s cooking performance today!
Add to cart now for an affordable fix with free shipping on your entire order!
XPARTCO 4392065 Dryer Maintenance Kit Replaces 349241T, 341241, WP691366
The XPARTCO 4392065 is an aftermarket dryer maintenance and repair kit containing the three most commonly replaced drum drive components for Whirlpool-family 29-inch dryers including Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Admiral, Estate, Crosley, Inglis, and Magic Chef. The kit includes the drum belt (341241), idler pulley (691366), and rear drum support roller kit (349241T) — the three parts that work together to drive and support the dryer drum, and that most frequently cause squealing, thumping, no heat, and drum-not-spinning issues when worn.
Replacing all three parts together in a single repair is the recommended approach — since these components wear at similar rates and the dryer must be fully disassembled to access any one of them, doing all three at once saves significant time and cost compared to replacing them individually. The kit contains everything needed: 1 drum belt, 1 idler pulley, 2 drum support rollers, 4 tri-rings, and 2 retaining washers. Installs in 45–60 minutes with basic hand tools.
Quick Answer
The XPARTCO 4392065 Dryer Maintenance Kit fixes squealing, thumping, no heat, and drum-not-spinning issues in Whirlpool-family 29" dryers in a single repair. Includes 1x 341241 drum belt (92-1/4" x 1/4", 4 ribs), 1x 691366 idler pulley, 2x 349241T drum rollers, 4x tri-rings, and 2x retaining washers. Compatible with Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Admiral, Estate, Crosley, Inglis, and Magic Chef dryers.
Common Problems This Kit Fixes
Loud squealing, squeaking, or thumping noise during the drying cycle
Dryer drum not spinning — motor runs but belt has broken
Clothes not tumbling or drying properly
Grinding or rumbling noise from the drum area
Dryer drum spinning unevenly or stopping intermittently
Belt repeatedly slipping or breaking due to worn idler pulley
Drum vibrating excessively due to worn roller bearings
What's in the Kit
Part 1 of 3 — 1 included
341241 Dryer Drum Belt
92-1/4" L x 1/4" W · 4 ribs, 3 grooves · Neoprene rubber · Wraps around the drum and connects to the idler pulley and motor pulley to drive drum rotation
Part 2 of 3 — 1 included
691366 Idler Pulley
Sturdy plastic with metal shaft and idler arm · Maintains correct tension on the drum belt between the motor and drum · Self-lubricating bearing
Part 3 of 3 — 2 included
349241T Rear Drum Support Roller Kit
2 drum rollers · Reinforced self-lubricating metal bearings, thickened rubber wheel · Supports the rear of the drum as it rotates · Includes 4 tri-rings and 2 retaining washers
Replaces Part Numbers
Kit (4392065) cross-references:
4392065, 2014, 26000279435, 26000279436, 279435, 279436, 279708, 279708MS, 279709, 279709MS, 279860, 279948, 4392065VP, 587636, 80046, 8106, 8237, 8238, AWP39348, PD00002464, AH373087, EA373087, AP3131942, PS373087.
341241 Belt cross-references:
341241, 14210003, 2008, 26000341241, 26000349533, 31001026, 31531589, 3389628, 3392665, 3394651, 3399844, 341241VP, 345473, 349533, 529597, 53-0186, 53-1080, 53-1086, 53-1528, 53-1589, 53-2671, 53-2910, 660996, 660997, 661561, 693306, 694088, 694416, 694868, 695055, 697388, 8066065, 8206, 8210, 920H4, 920H5, 99906951, 99989673, 99989674, FSP341241, LB276, LB279, P46-037, P46-149, W10127457, W10131364, AH346995, AP32, EA346995, ER341241, AP2946843, PS346995, TJ341241.
691366 Idler Pulley cross-references:
WP691366, 691366, 239477, 26000691366, 3346, 337116, 337407, 337510, 3388345, 338946, 3394332, 347034, 347226, 347277, 4319391, 688166, 691366BULK, 8207, 99989677, DE412, K35-163, W10612905, AP6010582, PS11743765.
349241T Drum Roller cross-references:
349241T, 26000349241, 337089, 3389901, 3397588, 3397590, 340352, 3436, 349241, 349241TVP, 661562, 8170, 8205, 99989678, 99989679, AH347627, EA347627, K34-895, AP3098345, PS347627.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This kit is compatible with select 29-inch large-capacity gas and electric dryers from the following brands:
Whirlpool dryers (gas and electric)
Kenmore / Sears dryers (select Whirlpool-built models)
Maytag dryers (gas and electric)
Amana dryers
KitchenAid dryers
Roper dryers
Admiral dryers
Estate dryers
Crosley dryers
Inglis dryers
Magic Chef dryers
Note: This kit is designed for 29-inch large-capacity Whirlpool-family dryers. If your dryer is a compact or stackable model, verify compatibility with our support team before ordering.
Key Features
Three-part kit addresses the most common drum drive failures in a single repair — saves time and cost vs. replacing parts individually
Belt: 92-1/4" x 1/4", 4 ribs, 3 grooves — premium neoprene rubber resists cracking, heat, and stretching
Idler pulley: sturdy plastic with metal shaft and self-lubricating bearing — maintains correct belt tension
Drum rollers: 2 included — reinforced self-lubricating metal bearings and thickened rubber wheels for quiet, stable drum support
All hardware included: 4 tri-rings and 2 retaining washers — everything needed for complete installation
Since the dryer must be disassembled to access any one of these parts, replacing all three at once eliminates repeated teardowns
Compatible with 11 major appliance brands on the Whirlpool 29-inch platform
Aftermarket replacement built to OEM-equivalent quality standards
DIY repair — installs in 45–60 minutes with basic hand tools
Product Specifications
Kit Part Number
4392065
Condition
Aftermarket Replacement
Application
29-inch Gas and Electric Dryers
Kit Includes
1x 341241 Drum Belt, 1x 691366 Idler Pulley, 2x 349241T Drum Rollers, 4x Tri-rings, 2x Retaining Washers
Belt Length
92-1/4 inches
Belt Width
1/4 inch
Belt Ribs
4 ribs, 3 grooves
Belt Material
Neoprene rubber
Idler Pulley Material
Plastic / Metal
Drum Roller Quantity
2 rollers (replace both at same time)
Roller Lubrication
Self-lubricating bearings — no grease needed
Compatible Brands
Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Admiral, Estate, Crosley, Inglis, Magic Chef
Installation Notes
⚠️ Unplug Dryer Before Starting Disconnect power (and shut off gas for gas dryers) before beginning. Remove the lint screen and unscrew the Phillips screws inside the lint screen housing. Use a putty knife to release the top panel clips and lift the top panel. Remove the front panel to access the drum. Release belt tension at the idler pulley, then lift the drum out. Remove the old belt, idler pulley, and drum rollers. Install the 2 new 349241T rollers onto the rear bulkhead shafts, pressing the new tri-rings and washers into place. Install the new 691366 idler pulley onto the idler arm. Loop the new 341241 belt around the drum with the ribbed side facing inward, then route it around the idler pulley and motor pulley. Reinstall the drum, reassemble the front and top panels, and restore power. Run a test cycle to confirm quiet operation. Tools needed: Phillips screwdriver, 1/4" nut driver, putty knife, needle-nose pliers, flat pry tool.
Frequently Asked Questions
Why should I replace all three parts at the same time?
The drum belt, idler pulley, and drum support rollers all work together as a system and wear at similar rates under the same conditions. Since the dryer must be fully disassembled to access any one of these parts, replacing all three in a single repair is far more cost-effective than replacing them one at a time — which would require three separate teardowns. This is the same reason the 4392065 maintenance kit was designed: one repair, all three parts, done.
What does each part in this kit do?
The 341241 drum belt wraps around the outside of the drum and connects to the idler pulley and motor pulley — the motor drives the belt, which spins the drum. The 691366 idler pulley maintains tension on the belt so it grips the drum and motor pulley properly. The 349241T drum rollers are support wheels mounted on the rear of the dryer that cradle and support the back edge of the drum as it rotates. All three are essential to smooth, quiet drum operation.
How is this kit different from the 4392067 repair kit?
The 4392065 and 4392067 kits are designed for different Whirlpool-family dryer generations. The 4392065 uses the 341241 belt (92-1/4" x 1/4", 4 ribs) and the 691366 idler pulley, and is for older 29-inch Whirlpool-family dryers. The 4392067 uses the 661570V belt (93-1/2" x 1/4", 4 ribs) and the W10837240 idler arm assembly, and is for newer Whirlpool-family dryers (those with the lint screen inside the door). Use your model number to confirm which kit fits your specific dryer before ordering.
Do I need to lubricate the drum rollers after installing?
No — the 349241T drum rollers include self-lubricating bearings and do not require any additional grease or oil after installation. Applying grease to self-lubricating rollers is not recommended and can actually attract lint and debris, causing the rollers to wear faster.
Is this an OEM or aftermarket kit?
This is an aftermarket replacement kit built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM kit, but all three included components are manufactured from premium neoprene rubber, durable plastic, and metal to match the dimensions and performance of the original 4392065 kit parts.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
XPARTCO 349241T Dryer Drum Roller Set (2-Pack)
The XPARTCO 349241T is an aftermarket replacement dryer rear drum support roller set compatible with a wide range of Whirlpool-family 29-inch dryers including Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Crosley, Estate, Inglis, Admiral, and Magic Chef. The drum support rollers are cylindrical rubber-and-metal wheels mounted on shafts at the rear of the dryer cabinet that cradle and support the outer edge of the drum as it rotates. Without the rollers, the drum would drag directly on the cabinet, causing rapid wear and generating the loud thumping or squealing noise that indicates failing rollers.
This set includes 2 drum rollers, 4 tri-ring retaining clips, and 2 retaining washers — everything needed for a complete rear roller replacement. Each roller measures 3-1/4"L x 1"W x 3-1/4"H and is constructed from rubber over a metal bearing hub with a plastic axle support. Both rollers must always be replaced at the same time. The set directly replaces 349241, 349241TVP, 8170, 8205, 337089, 340352, 661562, 3389901, 3397588, 3397590, AP3098345, PS347627, and several additional cross-reference numbers. Often replaced together with the drum belt (341241) and idler pulley (691366 or 279640) for a complete drum drive repair. Installs in 30–60 minutes with basic hand tools.
Quick Answer
The XPARTCO 349241T Dryer Drum Roller Set fixes Whirlpool-family 29" dryers that are squealing, thumping, rumbling, or where the drum is not turning smoothly. Set of 2 rollers with 4 tri-rings and 2 retaining washers. 3-1/4"L x 1"W x 3-1/4"H each. Replace both rollers at the same time. Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Crosley, Estate, Inglis, Admiral, and Magic Chef 29" dryers. Replaces 349241, 8170, 8205, 337089, 3389901, AP3098345, PS347627.
Common Problems This Part Fixes
Loud thumping, rumbling, or squealing noise during the drying cycle
Grinding or scraping sound when the drum is turning
Drum turning unevenly or wobbling during operation
Drum not spinning — rollers so worn they can no longer support the drum
Squealing or squeaking that gets worse over time as roller bearings degrade
Marks or scuff lines on clothes — drum dragging against the dryer cabinet
Excessive vibration during the drying cycle
Replaces Part Numbers
This drum roller set directly replaces the following OEM and cross-reference part numbers:
349241T, 26000349241, 337089, 3389901, 3397588, 3397590, 340352, 3436, 349241, 349241TVP, 661562, 8170, 8205, 99989678, 99989679, AWP39168, AH347627, EA347627, K34-895, PD00002257, EAP347627, AP3098345, PS347627.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This drum roller set is compatible with select 29-inch gas and electric dryers from the following brands:
Whirlpool dryers (gas and electric — 29" models)
Kenmore / Sears dryers (Whirlpool-built models)
Maytag dryers
KitchenAid dryers
Amana dryers
Roper dryers
Crosley dryers
Estate dryers
Inglis dryers
Admiral dryers
Magic Chef dryers
Note: The 349241T rollers are for 29-inch Whirlpool-family dryers. Newer Whirlpool Duet front-load dryers and larger-capacity models use different roller part numbers (such as WPW10314173 / 8536974). Always verify your model number before ordering.
Key Features
Set of 2 rear drum support rollers — supports and cradles the drum as it rotates for smooth, quiet operation
Includes all hardware: 2 rollers, 4 tri-ring retaining clips, 2 retaining washers — everything needed for a complete installation
Dimensions: 3-1/4"L x 1"W x 3-1/4"H per roller
Rubber wheel over metal bearing hub with plastic axle support — designed to resist wear and heat under continuous drum load
Both rollers must be replaced at the same time — replacing only one results in uneven drum support and accelerated wear on the new roller
Often replaced together with the drum belt (341241) and idler pulley (691366 or 279640) for a complete drum drive repair
Compatible with 11 major appliance brands on the Whirlpool 29-inch platform
Aftermarket replacement built to OEM-equivalent quality standards
DIY repair — installs in 30–60 minutes with basic hand tools
Product Specifications
Part Number
349241T
Part Type
Dryer Rear Drum Support Roller Set
Condition
Aftermarket Replacement
Application
29-inch Gas and Electric Dryers
Quantity
Set of 2 rollers (replace both at the same time)
Roller Dimensions
3-1/4"L x 1"W x 3-1/4"H (per roller)
Material
Rubber wheel / Metal bearing hub / Plastic axle support
Color
Black / White
Kit Includes
2 drum rollers, 4 tri-ring retaining clips, 2 retaining washers
Often Replaced With
341241 Drum Belt, 691366 or 279640 Idler Pulley
Compatible Brands
Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Crosley, Estate, Inglis, Admiral, Magic Chef
Installation Notes
⚠️ Unplug Dryer Before Starting Disconnect power (and shut off gas for gas dryers) before beginning. Remove the lint screen and unscrew the screws inside the lint screen housing. Use a putty knife to release the top panel spring clips and lift the top panel. Remove the front panel to access the drum. Release the drive belt from the idler pulley, lift the drum forward, and set it aside. The rear drum support rollers are mounted on shafts on the rear bulkhead — each roller is secured with a tri-ring clip and a retaining washer. Use needle-nose pliers to remove the old tri-ring clips, then slide the old rollers off the shafts. Install the new rollers, new retaining washers, and new tri-ring clips on the shafts. Reinstall the drum, re-route the belt around the motor and idler pulley, and reassemble the front and top panels. Restore power and run a test cycle to verify quiet, smooth drum operation. Tip: while the dryer is open, inspect and replace the drum belt (341241) and idler pulley (691366 or 279640) if worn. Tools needed: Phillips screwdriver, 1/4" or 5/16" nut driver, putty knife, needle-nose pliers.
Frequently Asked Questions
What do the drum support rollers do?
The rear drum support rollers are cylindrical wheels mounted on fixed shafts at the back of the dryer cabinet. As the drum rotates, its rear outer rim rests on these rollers, which carry the drum's weight and allow it to spin smoothly and quietly. When the rubber wheels wear down or the bearing hubs corrode, the drum no longer rides smoothly on the rollers — causing thumping, rumbling, or squealing noises that get progressively worse. In severe cases, worn rollers allow the drum to sag and drag against the cabinet rear panel.
Why must I replace both rollers at the same time?
Both rear drum support rollers carry the same load and experience the same wear through every drying cycle. When one roller fails, the other has been under the same stress for the same number of cycles and is almost certainly near the end of its useful life. Replacing only the failed roller leaves one worn roller supporting the drum unevenly, which puts extra stress on the new roller and causes it to wear out much faster. Replace both rollers at the same time to ensure even drum support and get the full service life from the new parts.
Should I also replace the belt and idler pulley at the same time?
Yes — this is the ideal time. Since the dryer must be fully disassembled to access the rear drum rollers, replacing the drum belt (341241) and idler pulley (691366 or 279640) at the same time is strongly recommended. All three parts wear at similar rates, and a worn belt or idler pulley is often what caused the rollers to wear prematurely. Doing all three in one repair eliminates the most common drum drive failure points and saves you from repeating the teardown in the near future. The 4392065 maintenance kit includes all three parts together.
What causes dryer drum rollers to wear out?
Drum rollers wear naturally over time from the continuous load of supporting the rotating drum. The most common accelerating factors are operating the dryer with a worn or broken belt (which allows the drum to sag and puts extra weight on the rollers), running very large or heavy loads frequently, and allowing lint to accumulate around the roller shafts, which causes the bearings to run dry and wear faster. Regular dryer maintenance — including cleaning lint from around the drum and periodically checking the belt — helps extend roller life.
Is this an OEM or aftermarket part?
This is an aftermarket replacement set built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured from rubber, metal, and plastic to match the dimensions and load-bearing performance of the original 349241T drum roller set.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
XPARTCO DC61-01215B Dryer Idler Tension Spring – Compatible with Samsung & Kenmore Dryers
Product Description
Restore proper belt tension and smooth drum rotation with the XPARTCO DC61-01215B Dryer Idler Tension Spring. This high-quality replacement spring maintains correct tension on the idler pulley, ensuring the dryer belt stays tight during operation. A worn or broken tension spring can cause belt slippage, squealing noises, drum not turning, or dryer stopping mid-cycle. Replacing it with this durable XPARTCO spring helps maintain reliable dryer performance.
Replaces Part Numbers
DC61-01215B, 2069087, DC61-01215A, DE1215B, PD00027514, EAP4206154, AP4211487, PS4206154.
Compatibility
This replacement idler tension spring fits select Samsung and Kenmore (Samsung-manufactured) dryers.
Example compatible models include (but are not limited to):Samsung DV42H5000EW, DV45H7000EWKenmore 592-89045, 592-89047
Always verify your dryer’s model number before ordering.Contact our support team if you’re unsure.
✅ Key Features
🔄 Aftermarket Replacement – Matches OEM tension and fit specifications
🔧 Maintains Proper Belt Tension – Keeps dryer belt tight and aligned
🔇 Reduces Noise & Slippage – Prevents squealing and belt skipping
💪 Durable Spring Steel Construction – Built for long-lasting elasticity
🛡️ Fixes Common Issues – Solves drum not turning, belt slipping, or abnormal noises
📐 Product Specification
Part Number: DC61-01215B
Component Type: Dryer Idler / Belt Tension Spring
Material: High-tensile spring steel
Application: Idler pulley tension control
Mounting: Hooks between idler arm and cabinet
Compliance: Built to OEM-equivalent quality standards (not OEM)
🛠️ Installation Notes
Tools Needed: Phillips screwdriver, needle-nose pliers
⚠️ Safety First: Always unplug the dryer before servicing to prevent electrical shock.
Steps:
Disconnect power and open the dryer cabinet.
Locate the idler pulley and tension spring.
Remove the worn or broken spring.
Install the new XPARTCO DC61-01215B spring in the same mounting points.
Reassemble dryer panels and restore power.
Run a test cycle to confirm proper belt tension.
⏱️ Time Required: 20–30 minutes
📦 Shop With Confidence
🚚 Free Shipping on All Orders
⚙️ Trusted Appliance Parts Supplier
🔄 30-Day Return Policy
Restore proper belt tension and smooth dryer operation — Add to Cart Now for a dependable, budget-friendly repair!
XPARTCO 8182703 Washer Shock Absorber Replaces WP8182703
The XPARTCO 8182703 is an aftermarket replacement front-load washer shock absorber compatible with select Whirlpool, Maytag, Kenmore, KitchenAid, Amana, Jenn-Air, Admiral, and Roper front-load washers in the GHW, WFW, MHWE, MFW, and KHWS series. The shock absorber is a hydraulic dampener that connects the outer washer tub to the base frame. During the spin cycle, the shock absorbers absorb and dampen the vibrations and movement generated by the spinning drum — keeping the washer stable, quiet, and protecting internal components from damage caused by excessive movement.
Most compatible Whirlpool-family front-load washers use four shock absorbers — two at the front and two at the rear. When one or more shock absorbers wear out, the outer tub vibrates excessively, causing loud banging or thumping during the spin cycle. It is strongly recommended to replace all four shock absorbers at the same time. This listing is for a single shock absorber. It directly replaces WP8182703, 8181646, 1173231, and several additional cross-reference numbers. Installs in 30–45 minutes with basic hand tools.
Quick Answer
The XPARTCO 8182703 Washer Shock Absorber fixes front-load washers that shake violently, bang loudly, or walk across the floor during the spin cycle. The shock absorber dampens tub vibration. Most models use 4 shock absorbers — replace all 4 at the same time. Sold individually. Compatible with Whirlpool, Maytag, Kenmore, KitchenAid, Amana, Jenn-Air, Admiral, and Roper front-load washers. Replaces WP8182703, 8181646, AP6011831, and more.
Common Problems This Part Fixes
Violent shaking or vibrating during the spin cycle
Loud banging, thumping, or clunking noise during spin
Washer "walking" across the floor during the spin cycle
Outer tub hitting the sides of the cabinet during high-speed spin
Spin cycle errors caused by excessive tub movement triggering the imbalance sensor
Visible oil leak, broken mount, or collapsed shock absorber body
Washer repeatedly pausing spin cycle and redistributing the load without resolving the vibration
Replaces Part Numbers
This shock absorber directly replaces the following OEM and cross-reference part numbers:
WP8182703, 8182703, 1173231, 8181646, EAP11745030, AWP48892, PD00003153, AP6011831, PS11745030.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This shock absorber is compatible with select front-load washers from the following brands and series:
Whirlpool front-load washers — GHW and WFW series
Maytag front-load washers — MHWE and MFW series
Kenmore / Sears front-load washers (select Whirlpool-built models)
KitchenAid front-load washers — KHWS series
Amana front-load washers
Jenn-Air front-load washers
Admiral front-load washers
Roper front-load washers
Important: Most compatible models use 4 shock absorbers (2 front, 2 rear). This part is sold individually. It is strongly recommended to replace all 4 at the same time, as the remaining absorbers have experienced the same wear and will fail soon after.
Key Features
Hydraulic dampener that connects the outer washer tub to the base frame — absorbs spin cycle vibration and prevents tub-to-cabinet contact
Keeps the washer stable and quiet during high-speed spin cycles, protecting drum bearings, seals, and cabinet from premature wear
High-quality reinforced construction — excellent toughness, oil resistance, and resistance to weak acids and alkalis for long service life
Direct replacement for WP8182703 and 8181646 — no modification required
Compatible with Whirlpool GHW, WFW, Maytag MHWE, MFW, and KitchenAid KHWS series front-load washers
Sold individually — most models require 4 shock absorbers; replace all 4 at the same time
Aftermarket replacement built to OEM-equivalent quality standards
DIY repair — installs in 30–45 minutes with basic hand tools
Product Specifications
Part Number
8182703
OEM Part Number
WP8182703
Part Type
Front-Load Washer Shock Absorber (Hydraulic Dampener)
Condition
Aftermarket Replacement
Application
Front-Load Washers
Quantity Per Washer
4 (2 front, 2 rear) — sold individually
Compatible Brands
Whirlpool, Maytag, Kenmore, KitchenAid, Amana, Jenn-Air, Admiral, Roper
Compatible Series
GHW, WFW, MHWE, MFW, KHWS
Installation Notes
⚠️ Unplug Washer and Shut Off Water Before Starting Unplug the washer and turn off the water supply before beginning. To access the front shock absorbers, remove the lower front access panel. To access the rear shock absorbers, pull the washer away from the wall, disconnect the water hoses, and remove the rear panel. The shock absorbers connect the outer tub to the base frame with mounting pins at the top and bottom — turn the shock absorber 90 degrees at both pins to release and remove it. Install the new 8182703 shock absorber by inserting the pins into the top and bottom mounting brackets and rotating 90 degrees to lock in place. Replace all 4 shock absorbers during the same repair. Reconnect all panels and water hoses, plug in the washer, restore water supply, and run a spin cycle to verify normal operation. Work gloves are recommended as there are sharp edges inside the cabinet. Tools needed: Phillips screwdriver, channel-lock pliers, work gloves.
Frequently Asked Questions
What does the washer shock absorber do?
The shock absorbers are hydraulic dampeners that connect the outer washer tub to the base frame of the machine. During the spin cycle — when the drum spins at high speeds — the shock absorbers absorb and dampen the vibrations and movement of the heavy outer tub, keeping it centered and preventing it from striking the sides of the washer cabinet. Without functioning shock absorbers, the washer vibrates violently, makes loud banging noises, and can "walk" across the floor during spin, potentially damaging internal components over time.
How many shock absorbers does my front-load washer have?
Most Whirlpool-family front-load washers compatible with the 8182703 shock absorber use four shock absorbers — two mounted at the front of the tub and two at the rear. This listing is for a single shock absorber. When replacing shock absorbers, it is strongly recommended to replace all four at once, as they all experience the same amount of use and the remaining absorbers are likely to fail soon after the first one.
What is the difference between 8182703 and WP8182703?
These are the same shock absorber. WP8182703 is the updated Whirlpool OEM part number that superseded the original 8182703. The 8181646 is also a cross-reference to this same part. This aftermarket replacement is compatible with all three numbers.
My washer still vibrates after replacing the shock absorbers — what else could it be?
If vibration persists after replacing all four shock absorbers, other possible causes include an unbalanced or overloaded drum, worn drum bearings, a failing suspension spring, or the washer not being level on the floor. Check that the washer's leveling feet are adjusted so all four corners are in firm contact with the floor. Also confirm the load is not oversized — overloading is the most common cause of spin vibration and can prematurely wear shock absorbers.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured from high-quality reinforced materials to match the dimensions and performance of the original WP8182703 shock absorber.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
EXP640 Dryer Belt and Idler Pulley Set – Replaces 661570V & 279640 – Compatible with Whirlpool, Maytag & Kenmore Dryers
Product Description
Restore smooth drum rotation and eliminate dryer noise with the EXP640 Dryer Belt and Idler Pulley Set. This high-quality aftermarket repair kit includes one drum belt and one idler pulley, providing a convenient solution for common belt tension and tumbling issues.
If your dryer is squealing, not turning, or producing uneven drying results, worn belt and pulley components are often the cause. Replacing both parts together helps restore proper belt tension, reduce noise, and extend the life of your dryer.
This kit includes:
1 Drum Belt (Replaces 661570V)
1 Idler Pulley (Replaces 279640)
Belt Replaces Part Numbers
661570V, 661570, 3387610, 3389728, 3393999, 339728, 661570VP, PD00023608, FIX382430, AP5983729, PS11722115
Idler Pulley Replaces Part Numbers
279640, 279640VP, 2958, 3388672, 697692, TJ279640, W10468057, AH334244, EA334244, ER279640, PD00002356, EAP334244, AP3094197, PS334244.
Compatibility
This dryer belt and idler pulley repair kit fits select Whirlpool, Maytag, Kenmore (Whirlpool-manufactured), Amana, Estate, and Roper dryers.
Common compatible models include (but are not limited to):
Whirlpool WED4815EW
Maytag MEDC215EW
Kenmore 110.60612990
Always verify your dryer’s model number before ordering.Contact our support team if you’re unsure.
✅ Key Features
🔄 Complete Repair Kit – Includes one drum belt and one idler pulley
🌀 Restores Smooth Drum Rotation – Maintains proper belt tension
🔇 Reduces Noise & Vibration – Fixes squealing or slipping belt issues
💪 Durable Construction – Reinforced belt and long-life pulley bearing
💰 Cost-Effective Solution – Replace two common wear parts at once
📐 Product Specification
Kit Number: EXP640
Includes:
(1) Dryer Drum Belt – Replaces 661570V
(1) Dryer Idler Pulley – Replaces 279640
Application: Dryer drum drive system
Material: Reinforced rubber belt, metal pulley with bearing
Quality Level: Aftermarket replacement kit (not OEM)
🛠️ Installation Notes
Tools Needed: Phillips screwdriver, nut driver
⚠️ Safety First: Unplug the dryer before servicing to avoid electrical shock.
Basic Steps:
Disconnect dryer power.
Remove the top and front panels (model dependent).
Remove the drum and old belt and pulley.
Install the new idler pulley onto the idler arm.
Route the new belt around the drum and motor pulley.
Reassemble the dryer and test operation.
⏱️ Time Required: 30–45 minutes
📦 Shop With Confidence
🚚 Free Shipping on All Orders
⚙️ Trusted Aftermarket Appliance Parts
🔄 30-Day Return Policy
Restore quiet, reliable dryer performance — Add to Cart Now for a complete repair solution!
285785 Washer Transmission Clutch - Compatible with Whirlpool, Kenmore, KitchenAid, Maytag, Amana, Roper, and Other Washers
Product Description
Restore your washer’s performance with the replacement 285785 Washer Transmission Clutch. This high-quality replacement clutch assembly, designed for direct-drive (beltless) Whirlpool, Kenmore, KitchenAid, Maytag, Amana, Roper, and other washer models, connects the transmission to the inner tub during the spin cycle and the agitator during the wash cycle. Constructed from durable plastic and metal, this clutch assembly includes a clutch with liner, brake cam driver, retaining clip, blue spring for large capacity (27") washers, and black spring for compact (24") washers. It addresses issues like slow spinning, failure to agitate, burning smells, or excessive shaking.
Note: Includes one clutch assembly with hardware. Disconnect power before installation.
Replaces part numbers: 285785, 2670, 285331, 285380, 285422, 285540, 285761, 285785VP, 3350015, 3350114, 3350115, 3351342, 3351343, 387888, 388948, 388949, 3946794, 3946847, 3951311, 3951312, 62699, 63174, 63765, 64176, PD00002503, EAP334641, AH334641, EA334641, J27-662, LP326, AP3094537, PS334641.
Compatibility:
Compatible with models including but not limited to:
Whirlpool: WTW5300SQ0, LSR7233EQ0, LSR8433KQ0, LSQ9544KQ0
Kenmore: 110.26902690, 110.28762790, 110.29822800
KitchenAid: KAWS750JQ0, KAWS850JQ0
Maytag: MAV6451AWW, MAV9750AWW
Amana: NTW4500XQ0
Roper: RAS8245EQ1, RTW4440XQ0
Inglis: ITW4300SQ0
Verify your model number or contact our support team for assistance.
Key Features:
✅ Brand and Models Compatibility: Fits select Whirlpool, Kenmore, KitchenAid, Maytag, Amana, Roper, Inglis, and other direct-drive washer models.
🔥 Specifications: replacement clutch assembly, plastic and metal, 4-1/2"L x 4-1/2"W x 1-1/8"H, includes clutch w/liner, brake cam driver, retaining clip, blue spring (1.24" for large capacity 27" washers), black spring (1.46" for compact 24" washers).
💰 Cost-Effective Alternative: replacement clutch offers OEM-equivalent performance at a lower price.
🛠️ Easy Installation: Requires a socket set, screwdrivers, work gloves; typically installed in 1–2 hours.
🛡️ Reliable Fixes: Resolves slow spinning, failure to agitate, burning smells, excessive shaking, or noisy operation.
Installation Notes:
Safety First: Disconnect the washer from the power source before installation.
Shop Parts-O-Matic for high-quality replacement appliance parts with a 30-day return policy. Keep your washer spinning and agitating smoothly today!
Add to cart now for a budget-friendly fix!
