Search results for "filter housing"

XPARTCO 4349 Door Latch Kit for Air Cleaner (4-Pack) Replaces Aprilaire 4349 The XPARTCO 4349 is an aftermarket replacement door latch kit compatible with Aprilaire Model 2200 and Model 2400 whole-house media air cleaners. Each cabinet uses a set of spring-loaded latches to hold the access door securely against the cabinet, keeping the seal tight so unfiltered air can't bypass the media filter. Over time these plastic latches crack, snap, or lose their spring tension from repeated opening and closing during filter changes, causing the door to sit loose, rattle, or fail to seal properly against the cabinet gasket. This kit includes 4 latches — enough to replace every latch on one cabinet door in a single order — manufactured to match the fit and mounting points of the original Aprilaire "new style door" latch design. The genuine Aprilaire 4349 was discontinued by the manufacturer in January 2022; this XPARTCO version is an aftermarket-manufactured equivalent built to keep these still-common air cleaner cabinets in service. Installs in under 10 minutes with no tools required. Quick Answer The XPARTCO 4349 Door Latch Kit fixes Aprilaire Model 2200 and Model 2400 whole-house air cleaners with a loose, rattling, or poorly sealing access door caused by cracked or worn-out latches. 4-pack — enough for a full door. Designed for the Aprilaire "new style door." No tools required for installation. The genuine Aprilaire 4349 is discontinued; this is an aftermarket-manufactured equivalent. Classic symptom: door won't stay shut, or air smell/bypass around the cabinet edge. Common Problems This Part Fixes Air cleaner access door won't stay closed or pops open on its own Door rattles or feels loose against the cabinet Visible cracked, broken, or missing latch tabs on the door Poor door seal allowing unfiltered air to bypass the media filter Musty or dusty smell around the cabinet edge from an incomplete seal Difficulty keeping the door aligned during filter changes Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This door latch kit directly replaces the following OEM part number: 4349 We were not able to confirm any additional cross-reference or alternate part numbers for this item at this time. If you have one, contact our support team before ordering and we will verify compatibility. Compatibility This latch kit is compatible with the following Aprilaire whole-house media air cleaners: Aprilaire Model 2200 whole-house air cleaner Aprilaire Model 2400 whole-house air cleaner Note: This kit is designed for the "new style" door used on later production Model 2200 and 2400 units. Earlier cabinets used a different door and latch design that this kit does not fit. Compare your existing latch and door style before ordering, or contact our support team with your model number if you're unsure. Key Features Replacement door latch kit for Aprilaire Model 2200 and Model 2400 whole-house air cleaners Resolves loose, rattling, or non-sealing access door caused by cracked or worn latches 4-pack — enough latches to fully replace one cabinet door Matches the fit and mounting points of the original Aprilaire "new style door" latch No tools required — snap-fit installation Helps maintain a proper door seal so unfiltered air can't bypass the media filter Aftermarket replacement built to OEM-equivalent quality standards for a now-discontinued genuine part Product Specifications Part Number 4349 OEM Part Number Aprilaire 4349 (discontinued) Part Type Air Cleaner Cabinet Door Latch Kit Condition Aftermarket Replacement Quantity 4-Pack (1 full door set) Door Style New Style Door Application Aprilaire Model 2200 & 2400 Whole-House Air Cleaners Installation Snap-fit, no tools required Installation Notes ℹ️ No Tools Required Open the air cleaner cabinet door fully. Locate each damaged or missing latch along the edge of the door. Grip the old latch and pull firmly to release it from its mounting slot — if it's already broken, remove any remaining fragments from the slot. Line up the new latch tab with the mounting slot and press firmly until it snaps into place. Repeat for each latch being replaced. Close the door and check that it seats flush and securely against the cabinet gasket with no gaps. If the door still doesn't seal evenly after replacing all latches, check the door hinge alignment and the condition of the cabinet gasket itself. Frequently Asked Questions Is the genuine Aprilaire 4349 still available? No — Aprilaire discontinued the genuine 4349 latch kit in January 2022. This XPARTCO version is an aftermarket-manufactured equivalent designed to keep still-common Model 2200 and 2400 cabinets in service now that the original part is no longer produced. How many latches come in this kit, and how many do I need? This kit includes 4 latches, which is a full set for one cabinet door. Most installers replace all four at once even if only one or two have failed, since the remaining originals are usually close behind in wear. Will this fit my Aprilaire air cleaner? This kit is designed for the "new style door" used on Model 2200 and 2400 units. Earlier cabinets used a different door and latch design that this kit will not fit. Compare your existing latch shape to the product photos, or contact our support team with your model number to confirm before ordering. Do I need any tools to install this? No. The latches are a snap-fit design — pull the old one out of its mounting slot and press the new one in firmly until it clicks into place. No screwdrivers or other tools are needed. Shop With Confidence A U.S.-based appliance and HVAC parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance and air-quality equipment brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

Genuine OEM W10120998 Dryer Lint Screen Filter The Genuine OEM Whirlpool W10120998 is the lint screen filter for select Whirlpool-built dryers, including Kenmore, Maytag, Amana, Roper and other brands. The lint screen traps lint and debris from the exhaust air flowing out of the dryer to help prevent clogging and support performance. Replace it if it is damaged or missing. This is the original Whirlpool part, not an aftermarket equivalent. Lint screens differ between dryers, so check your model number before ordering. Clean and inspect the screen regularly. Quick Answer The Genuine OEM W10120998 Lint Screen Filter replaces a damaged or missing lint screen on a compatible Whirlpool-built dryer. Replaces W10120998, W10049370 and 8066170. Classic symptoms: long drying times, lint on clothes, or poor drying. Other problems can cause the same symptoms. Common Problems This Part Fixes Long drying times Lint on clothing Poor drying Damaged or missing lint screen Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This lint screen replaces or supersedes the following part numbers: W10120998, 1206293, 3390721, 8066170, 8572268, W10049370, W10120998VP, W10178353, W10596627, AP3967919, AWP40367, AH1491676, EA1491676, EAP1491676, PD00002655, PS1491676 Whirlpool uses many similar lint screen numbers for different dryers, and they are not interchangeable by number alone. If your old lint screen shows a different number, contact our support team and we'll check whether it matches. Compatibility This lint screen is listed for Kenmore, Whirlpool, Maytag, Amana, Roper, KitchenAid, Crosley, Inglis and other Whirlpool-built dryers, including these examples: Kenmore 11087994500, 11087983830, 11097195800, 11087994300 Whirlpool WED7500GW0, WGD7500GW0, WED6120HW0, 3LWGD4800YQ0 Maytag MGDB765FC0, MGDB850YG2, MGDB725BW0 Note: The models above are a small sample, not a full list. It fits only some models of each brand. Check your full model number against your parts diagram, or contact our support team to verify fit before ordering. Key Features Genuine OEM Whirlpool part, not an aftermarket equivalent Traps lint and debris from the dryer's exhaust air Slides into place in the lint compartment, with no tools required Replaces several earlier Whirlpool lint screen numbers Product Specifications Part Number W10120998 OEM Part Number W10120998 Part Type Dryer Lint Screen Filter Condition Genuine OEM Manufacturer Whirlpool Quantity 1 Lint Screen Application Select Whirlpool-Built Dryers Installation Notes ⚠️ Make Sure The Dryer Is Off And Cool Make sure the dryer is off and has cooled before you begin. Remove the old lint screen, clear any lint from the lint compartment, and slide the new screen into place. Follow your dryer's owner's manual for model-specific details. Clean and inspect the screen regularly, and avoid harsh chemicals or rough materials when cleaning. Frequently Asked Questions What does the lint screen do? It traps lint and debris from the exhaust air flowing out of the dryer, which helps prevent clogging. Replace it if it is damaged or missing. Is this an OEM or aftermarket part? This is a genuine OEM part from Whirlpool, not an aftermarket equivalent. Can I use a lint screen with a similar part number? Not by number alone. Whirlpool uses different lint screens for different dryers, so match the part number and your model number, or contact our support team and we'll check for you. Will this fit my dryer? It is listed for many Whirlpool-built dryers, but the model list above is only a sample. Check your full model number against your parts diagram, or contact our support team and we'll verify it before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

00701751 Refrigerator Genuine Defrost Heater Replaces Part Numbers:  00701751, 00660332, 2000209, 660332, 701751, AH3484061, EA3484061, PS3484061, OEM18267702, AP4566925, PS8735951. Description: This Defrost Heater Assembly is a Genuine part for Specific Bosch, Thermador refrigerator models. It plays a crucial role in the refrigerator's defrost cycle, melting away any frost that accumulates on the evaporator coils.   California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

Genuine OEM W11210463 Washer Water Inlet Valve The Genuine OEM Whirlpool W11210463 is the water inlet valve assembly for select Whirlpool, Maytag, Amana, Crosley, Admiral, Inglis and Roper washers. The valve controls the flow of hot and cold water into the washer. When it fails, the washer may not fill, may fill slowly or with too little water, or may leak. This is the original Whirlpool part, not an aftermarket equivalent. It is sold individually. Check your model number before ordering, because several similar inlet valves exist. Quick Answer The Genuine OEM W11210463 Water Inlet Valve replaces the inlet valve on a compatible washer when it has failed. Replaces W10701461, W10869803, W10883458, W11038696 and W11101906. Classic symptoms: the washer won't fill or fills slowly, leaks, or gets no hot or cold water. Common Problems This Part Fixes Washer won't fill, or fills slowly No hot or cold water Water leaking from the valve Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This water inlet valve replaces or supersedes the following part numbers: W11210463, W11038696, 4591539, W10701461, W10869803, W10883458, W11101906, AP6329219, PS12349269 If your old valve shows a different number, contact our support team and we'll check whether it matches. Compatibility This water inlet valve is listed for Whirlpool, Maytag, Amana, Crosley, Admiral, Inglis and Roper washers, including these examples: Whirlpool WTW4816FW3, NTW4516FW2, NTW4665GW0, RTW4516FW2, MVW4005SW0, ITW4871FW3, CWW3812RW0, VWW3809RW0 Maytag ATW4516HW0, NTW4516FW3 Amana NTW4516FW4, NTW4605EW1, NTW4655EW1 Crosley CAW11544EW2, CAW8350EW2 Admiral ATW4516MW0 Inglis ITW4671EW1, ITW4971EW1 Note: The models above are a sample, not a full list. Whirlpool sells similar inlet valves under other part numbers. Check your full model number against your parts diagram, or contact our support team to verify fit before ordering. Key Features Genuine OEM Whirlpool part, not an aftermarket equivalent Controls the flow of water into the washer Replaces five earlier Whirlpool valve part numbers Sold individually Product Specifications Part Number W11210463 OEM Part Number W11210463 Part Type Washer Water Inlet Valve Condition Genuine OEM Manufacturer Whirlpool Quantity 1 Valve Application Select Whirlpool-Built Washers Installation Notes ⚠️ Disconnect Power And Water Before Installing Unplug the washer and shut off the water supply before you begin, and wear work gloves. Disconnect the water hoses and the wire connectors from the old valve, noting where each goes, and remove it. Fit the new valve, reconnect the hoses and connectors, restore power and water, and check for leaks while the washer fills. Frequently Asked Questions My washer won't fill or fills slowly. Is this the part I need? It can be. Check that both water supplies are on and the hose screens are clear first, since a blocked screen can cause the same symptom. If those are fine, the inlet valve may have failed. Is this an OEM or aftermarket part? This is a genuine OEM part from Whirlpool, not an aftermarket equivalent. Does this replace my old valve number? It replaces W10701461, W10869803, W10883458, W11038696 and W11101906. If your valve shows another number, contact our support team and we'll check it. Will this fit my washer? It is listed for many Whirlpool-built models, but the model list above is only a sample. Check your full model number against your parts diagram, or contact our support team and we'll verify it before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

Genuine Frigidaire OEM Frigidaire 5304533220 Washer Water Fill Hose Assembly Genuine OEM internal valve-to-tub fill hose for select Frigidaire-built laundry centers and washer/dryer combination units. Product Overview The Frigidaire 5304533220 Washer Water Fill Hose Assembly is a Genuine OEM internal fill hose used to route incoming water from the washer water inlet valve to the wash tub on compatible laundry-center models. This is the valve-to-tub hose inside the appliance. It is not the external hot/cold household water-supply hose that connects the appliance to the wall faucets. Quick Answer 5304533220 is the Genuine Frigidaire OEM valve-to-tub washer fill hose. It replaces earlier Frigidaire numbers 5304508358 and 809191901 and is used on select Frigidaire, Kenmore, Crosley, and other Electrolux-manufactured laundry centers. Common Problems This Part May Fix Water leaking inside the washer cabinet during fill Cracked, split, hardened, or deteriorated fill hose Leak between the inlet-valve outlet and wash tub Loose or damaged internal water-fill connection Water dripping from the valve-to-tub hose during operation Replaces and Cross-References 5304533220, 5304508358, 809191901, AFR20016, AP7194866, EAP11775692, PD00076846, PS16745853 Cross-reference numbers are provided for identification. Always verify the full appliance model number before ordering. Compatibility Confirmed applications include select Frigidaire-built laundry centers and washer/dryer combinations such as: FLCE7523AW0 FLCE7523AW1 FLCE7522AW1 FLCE7522AW4 FFLE3900UW0 FFLE3900UW1 FFLG3900UW0 FFLE3911QW1 CFLE3900UW0 41761712511 41761732810 41771732810 Important: This is only a partial compatibility list. Confirm the complete model number from the appliance rating label before purchase. Key Features Genuine Frigidaire OEM replacement part Internal valve-to-tub fill hose Routes fill water from the inlet valve to the washer tub Direct replacement for 5304508358 and 809191901 Factory-style fit for compatible laundry centers Used on select Frigidaire, Kenmore, and related Electrolux-built models Product Specifications Manufacturer Part Number 5304533220 Brand Frigidaire Part Type Washer Internal Water Fill Hose Hose Location Water Inlet Valve to Wash Tub OEM Status Genuine OEM Appliance Type Laundry Center / Washer-Dryer Combo Condition New External Supply Hose? No — this is an internal appliance hose Installation Notes Disconnect electrical power to the appliance before service. Shut off both household water-supply valves. Access the washer inlet-valve and tub-fill connection according to the model-specific service procedure. Place towels or a shallow pan below the hose connections to catch residual water. Release the clamps and remove the old hose without damaging the valve outlet or tub fitting. Install the new hose fully onto both fittings and reinstall the clamps in their original positions. Restore water and inspect carefully for leaks before returning the appliance to service. Diagnostic tip: If water is leaking during fill, inspect the hose, clamps, inlet valve, and tub connection before replacing parts. A leak from the external household supply hose requires a different part. Frequently Asked Questions Is 5304533220 a Genuine OEM part? Yes. It is a Genuine Frigidaire OEM fill hose. Does 5304533220 replace 5304508358? Yes. 5304533220 supersedes 5304508358 and 809191901. Is this the hose that connects the washer to the wall faucet? No. This is an internal valve-to-tub fill hose located inside the laundry center. Can this part correct a washer leak? Yes, if the leak is caused by a cracked or damaged valve-to-tub fill hose or its connection. Inspect all nearby fittings and clamps before ordering. Shop With Confidence Verify your complete laundry-center model number before ordering. This listing is for the Genuine Frigidaire OEM internal valve-to-tub fill hose. Genuine Frigidaire OEMValve-to-Tub Fill HoseCompatibility SupportFast U.S. Shipping

Read more less

341241 Dryer Genuine OEM Drum Belt The 341241 is a Genuine OEM dryer drum belt compatible with a wide range of Whirlpool-family dryers including Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Admiral, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, Norge, Modern Maid, Hardwick, Caloric, and Ikea. The drum belt wraps around the outside of the dryer drum, loops around the motor pulley and idler pulley, and drives the drum to rotate during every drying cycle. Without a functioning belt, the drum cannot spin and clothes will not tumble or dry. Made from high-strength rubber with reinforced ribs, this belt measures 92-1/4 inches long x 1/4 inch wide and features 4 ribs and 3 grooves. It is flat on one side and ribbed on the other, and is built to resist cracking, stretching, and wear under the high heat and repeated tension cycles of daily dryer use. It also replaces some 5-rib, 4-groove belts. Installs in 30–45 minutes with basic hand tools. Quick Answer The 341241 Dryer Genuine OEM Drum Belt fixes dryers where the drum is not spinning, clothes are not tumbling, or a thumping/squealing noise is coming from the dryer. Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Admiral, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, and more. Measures 92-1/4" L x 1/4" W with 4 ribs and 3 grooves. Common Problems This Part Fixes Dryer drum not spinning — motor runs but drum stays still Clothes not tumbling during the drying cycle Thumping, squealing, or slapping noise during operation Dryer runs but produces no heat because drum is stationary Burning rubber smell coming from the dryer Visible broken or frayed belt pieces found inside the dryer cabinet Clothes taking too long to dry due to drum not rotating at correct speed Replaces Part Numbers This drum belt directly replaces the following OEM and cross-reference part numbers: 341241, 14210003, 2008, 26000341241, 26000349533, 31001026, 31531589, 3389628, 3392665, 3394651, 3399844, 341241VP, 345473, 349533, 529597, 53-0186, 53-1080, 53-1086, 53-1528, 53-1589, 53-2671, 53-2910, 660996, 660997, 661561, 693306, 694088, 694416, 694868, 695055, 697388, 8066065, 8206, 8210, 920H4, 920H5, 99906951, 99989673, 99989674, FSP341241, LB276, LB279, P46-037, P46-149, W10127457, W10131364, AH346995, AP32, EA346995, ER341241, AWP39161, PD00002263, EAP346995, AP2946843, PS346995, TJ341241. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drum belt is compatible with select dryers from the following brands: Whirlpool dryers (gas and electric) Kenmore / Sears dryers (select models) Maytag dryers KitchenAid dryers Amana dryers Roper dryers Admiral dryers Jenn-Air dryers Estate dryers Magic Chef dryers Crosley dryers Inglis dryers Norge, Modern Maid, Hardwick, Caloric, and Ikea dryers Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Drives the dryer drum via the motor pulley and idler pulley for smooth, consistent tumbling every cycle 92-1/4" length x 1/4" width — 4-rib, 3-groove design; flat on one side, ribbed on the other Also replaces some 5-rib, 4-groove belts — wide cross-compatibility across Whirlpool-family models Made from high-strength rubber with reinforced ribs — resists cracking, stretching, and heat damage Direct replacement for OEM part numbers 341241 and 8066065 — no modification required Compatible with over a dozen major appliance brands built on the Whirlpool platform Genuine OEM part — factory-exact fit, materials, and dimensions DIY-friendly repair — installs in 30–45 minutes with basic hand tools Often replaced together with the idler pulley (691366) and drum rollers (349241T) for a complete drum drive repair Product Specifications Part Number 341241 Part Type Dryer Drum Drive Belt Condition Genuine OEM Application Gas and Electric Dryers Length 92-1/4 inches Width 1/4 inch Ribs 4 ribs, 3 grooves Profile Flat on one side, ribbed on the other Material High-strength rubber with reinforced ribs Color Black Compatible Brands Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Admiral, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, Norge, Modern Maid, Hardwick, Caloric, Ikea Often Replaced With 691366 Idler Pulley, 349241T Drum Rollers Installation Notes ⚠️ Safety First — Unplug Dryer Before Starting Unplug the dryer from the power source (and shut off the gas supply for gas dryers) before beginning any repair. Remove the lint screen, then unscrew the two Phillips screws inside the lint filter housing. Use a putty knife 2 inches from each front corner to release the top panel clips and lift the top panel. Remove the front panel to access the drum. Release belt tension at the idler pulley, lift the drum slightly, and slide the old belt off. Loop the new 341241 belt around the drum with the ribbed side facing down (toward the drum). Route the belt around the idler pulley and motor pulley — consult your model's service manual or a model-specific video for the correct belt path. Reassemble and run a test cycle. Tip: While the drum is out, inspect and replace the idler pulley (691366) and drum rollers (349241T) if worn. Tools needed: Phillips screwdriver, putty knife or flat pry tool. Frequently Asked Questions How does the 341241 differ from the W10205415 and 6602-001655 belts? All three are 92-inch dryer drum belts, but they differ in width and rib count. The 341241 is 1/4" wide with 4 ribs and 3 grooves. The W10205415 is 3/8" wide with 5 ribs and 4 grooves. The 6602-001655 is 5/16" wide with 5 ribs and 4 grooves designed for Samsung dryers. Always match the part number to your specific model — do not substitute based on appearance alone. Will this belt fit my Kenmore dryer? Many Kenmore dryers — especially the popular 110-series — are manufactured by Whirlpool and use the 341241 belt. Check your model number against the compatibility list and contact our support team if you need help confirming the fit before ordering. How do I know if my drum belt needs to be replaced? The most obvious sign is that the dryer motor hums but the drum does not spin. You may also notice a thumping or slapping sound during operation, a burning rubber smell, or clothes that are damp after a full cycle. Open the dryer cabinet to visually confirm if the belt is broken, frayed, or stretched. Should I also replace the idler pulley and drum rollers? Yes — since the dryer is already disassembled, it is highly recommended to inspect and replace the idler pulley (691366) and drum support rollers (349241T) at the same time. These parts wear at a similar rate and replacing all three together — often sold as a repair kit — prevents having to disassemble the dryer again in the near future. Is this an OEM or aftermarket part? This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It is the exact same belt that came installed in your dryer from the factory — same materials, dimensions, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

XPARTCO 341241 Dryer Drum Belt The XPARTCO 341241 is an aftermarket replacement dryer drum belt compatible with a wide range of Whirlpool-family dryers including Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Admiral, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, Norge, Modern Maid, Hardwick, Caloric, and Ikea. The drum belt wraps around the outside of the dryer drum, loops around the motor pulley and idler pulley, and drives the drum to rotate during every drying cycle. Without a functioning belt, the drum cannot spin and clothes will not tumble or dry. Made from high-strength rubber with reinforced ribs, this belt measures 92-1/4 inches long x 1/4 inch wide and features 4 ribs and 3 grooves. It is flat on one side and ribbed on the other, and is built to resist cracking, stretching, and wear under the high heat and repeated tension cycles of daily dryer use. It also replaces some 5-rib, 4-groove belts. Installs in 30–45 minutes with basic hand tools. Quick Answer The XPARTCO 341241 Dryer Drum Belt fixes dryers where the drum is not spinning, clothes are not tumbling, or a thumping/squealing noise is coming from the dryer. Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Admiral, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, and more. Measures 92-1/4" L x 1/4" W with 4 ribs and 3 grooves. Common Problems This Part Fixes Dryer drum not spinning — motor runs but drum stays still Clothes not tumbling during the drying cycle Thumping, squealing, or slapping noise during operation Dryer runs but produces no heat because drum is stationary Burning rubber smell coming from the dryer Visible broken or frayed belt pieces found inside the dryer cabinet Clothes taking too long to dry due to drum not rotating at correct speed Replaces Part Numbers This drum belt directly replaces the following OEM and cross-reference part numbers: 341241, 14210003, 2008, 26000341241, 26000349533, 31001026, 31531589, 3389628, 3392665, 3394651, 3399844, 341241VP, 345473, 349533, 529597, 53-0186, 53-1080, 53-1086, 53-1528, 53-1589, 53-2671, 53-2910, 660996, 660997, 661561, 693306, 694088, 694416, 694868, 695055, 697388, 8066065, 8206, 8210, 920H4, 920H5, 99906951, 99989673, 99989674, FSP341241, LB276, LB279, P46-037, P46-149, W10127457, W10131364, AH346995, AP32, EA346995, ER341241, AWP39161, PD00002263, EAP346995, 694088-NC, AP2946843, PS346995, TJ341241. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drum belt is compatible with select dryers from the following brands: Whirlpool dryers (gas and electric) Kenmore / Sears dryers (select models) Maytag dryers KitchenAid dryers Amana dryers Roper dryers Admiral dryers Jenn-Air dryers Estate dryers Magic Chef dryers Crosley dryers Inglis dryers Norge, Modern Maid, Hardwick, Caloric, and Ikea dryers Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Drives the dryer drum via the motor pulley and idler pulley for smooth, consistent tumbling every cycle 92-1/4" length x 1/4" width — 4-rib, 3-groove design; flat on one side, ribbed on the other Also replaces some 5-rib, 4-groove belts — wide cross-compatibility across Whirlpool-family models Made from high-strength rubber with reinforced ribs — resists cracking, stretching, and heat damage Direct replacement for OEM part numbers 341241 and 8066065 — no modification required Compatible with over a dozen major appliance brands built on the Whirlpool platform Aftermarket replacement built to OEM-equivalent quality standards DIY-friendly repair — installs in 30–45 minutes with basic hand tools Often replaced together with the idler pulley (691366) and drum rollers (349241T) for a complete drum drive repair Product Specifications Part Number 341241 Part Type Dryer Drum Drive Belt Condition Aftermarket Replacement Application Gas and Electric Dryers Length 92-1/4 inches Width 1/4 inch Ribs 4 ribs, 3 grooves Profile Flat on one side, ribbed on the other Material High-strength rubber with reinforced ribs Color Black Compatible Brands Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Admiral, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, Norge, Modern Maid, Hardwick, Caloric, Ikea Often Replaced With 691366 Idler Pulley, 349241T Drum Rollers Installation Notes ⚠️ Safety First — Unplug Dryer Before Starting Unplug the dryer from the power source (and shut off the gas supply for gas dryers) before beginning any repair. Remove the lint screen, then unscrew the two Phillips screws inside the lint filter housing. Use a putty knife 2 inches from each front corner to release the top panel clips and lift the top panel. Remove the front panel to access the drum. Release belt tension at the idler pulley, lift the drum slightly, and slide the old belt off. Loop the new 341241 belt around the drum with the ribbed side facing down (toward the drum). Route the belt around the idler pulley and motor pulley — consult your model's service manual or a model-specific video for the correct belt path. Reassemble and run a test cycle. Tip: While the drum is out, inspect and replace the idler pulley (691366) and drum rollers (349241T) if worn. Tools needed: Phillips screwdriver, putty knife or flat pry tool. Frequently Asked Questions How does the 341241 differ from the W10205415 and 6602-001655 belts? All three are 92-inch dryer drum belts, but they differ in width and rib count. The 341241 is 1/4" wide with 4 ribs and 3 grooves. The W10205415 is 3/8" wide with 5 ribs and 4 grooves. The 6602-001655 is 5/16" wide with 5 ribs and 4 grooves designed for Samsung dryers. Always match the part number to your specific model — do not substitute based on appearance alone. Will this belt fit my Kenmore dryer? Many Kenmore dryers — especially the popular 110-series — are manufactured by Whirlpool and use the 341241 belt. Check your model number against the compatibility list and contact our support team if you need help confirming the fit before ordering. How do I know if my drum belt needs to be replaced? The most obvious sign is that the dryer motor hums but the drum does not spin. You may also notice a thumping or slapping sound during operation, a burning rubber smell, or clothes that are damp after a full cycle. Open the dryer cabinet to visually confirm if the belt is broken, frayed, or stretched. Should I also replace the idler pulley and drum rollers? Yes — since the dryer is already disassembled, it is highly recommended to inspect and replace the idler pulley (691366) and drum support rollers (349241T) at the same time. These parts wear at a similar rate and replacing all three together — often sold as a repair kit — prevents having to disassemble the dryer again in the near future. Is this an OEM or aftermarket part? This is an aftermarket replacement built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is made from high-strength rubber to match the dimensions and performance of the original 341241 belt. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

XPARTCO 17438200000160 Gas Dryer Flame Switch The XPARTCO 17438200000160 is an aftermarket replacement gas dryer flame switch compatible with select Midea, Insignia gas dryers, including the MLG45N1BWW, MLG45N3BMG, MLG45N3BWW, MLG52S7AWW, CDG41N1AW/CDG45N1AW series, NSDRE67WH8A, NSFDRG67WH8A, NSDRE67WH8AC, NSTDRG75W1. The flame switch is a safety component mounted on the burner assembly that confirms a flame is actually present after the gas valve opens and the igniter lights the burner. If the switch does not detect a flame within the expected window, it signals the control board to shut off the gas valve, preventing unburned gas from continuing to flow into the dryer cabinet. When the flame switch fails, the dryer may not heat at all, may shut off the burner shortly after ignition (short-cycling the flame), may trip a no-heat fault code on models with digital displays, or — in rarer failure modes — may fail to shut off gas flow appropriately, which is a safety-relevant failure. It directly replaces 17438200000160 (Midea OEM). Installs in 30–45 minutes with basic hand tools. Quick Answer The XPARTCO 17438200000160 Gas Dryer Flame Switch fixes Midea gas dryers that won't heat, where the burner lights and then shuts off shortly after ignition, or where a no-heat fault is displayed. Mounted on the burner assembly — confirms flame presence after ignition and signals the control board to keep the gas valve open. Genuine Midea OEM part number. Compatible with Midea MLG45N1BWW, MLG45N3BMG, MLG45N3BWW, MLG52S7AWW, CDG41N1AW, and CDG45N1AW gas dryers. Common Problems This Part Fixes Gas dryer not heating — flame switch not confirming flame presence to the control board Burner lights briefly and then shuts off — flame switch failing to maintain the "flame confirmed" signal No-heat fault code displayed on models with digital control panels Dryer runs and tumbles normally but produces no heat Burner repeatedly cycling on and off rapidly during a heat cycle Visible damage, corrosion, or carbon buildup on the flame switch near the burner Replaces Part Numbers This flame switch directly replaces the following part number: 17438200000160, AP7153000, PS18188577. This is the Midea, Insignia manufacturer part number used across multiple Midea gas dryer models. Contact our support team with your model number if you need confirmation before ordering. Compatibility This flame switch is compatible with select Midea, Insignia gas dryers, including: Midea MLG45N1BWW gas dryer Midea MLG45N3BMG gas dryer Midea MLG45N3BWW gas dryer Midea MLG52S7AWW gas dryer (8.0 cu. ft. front load) Midea CDG41N1AW gas dryer (Criterion, air vent) Midea CDG45N1AW gas dryer (Criterion, air vent) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Confirms flame presence at the burner after ignition and signals the control board accordingly Safety component — helps ensure the gas valve closes promptly if a flame is not detected Mounts directly to the burner assembly in the same position as the original switch Genuine Midea manufacturer part number — designed as a direct fit for compatible models Compatible with Midea MLG45N1BWW, MLG45N3BMG, MLG45N3BWW, MLG52S7AWW, CDG41N1AW, and CDG45N1AW gas dryers Installs in 30–45 minutes with basic hand tools Product Specifications Part Number XP17438200000160 Part Type Gas Dryer Flame Switch Condition Aftermarket Replacement Application Gas Dryers (Midea platform) Location Mounted on the burner assembly Compatible Brands Midea Installation Notes ⚠️ Gas Appliance Safety Warning This part is installed in a gas dryer. Always unplug the dryer and shut off the gas supply at the shutoff valve before beginning any repair. If you smell gas at any point during or after installation, leave the area immediately and contact your gas utility provider. Do not restore power or gas until the repair is fully complete and all connections are confirmed secure. If you are not comfortable working on gas appliances or safety-relevant flame-detection components, have this part installed by a qualified technician. ⚠️ Wear Work Gloves — Access Requires Cabinet Disassembly Disconnect power and shut off gas before beginning. Wear work gloves throughout — there are sharp metal edges inside the dryer cabinet. Remove the lint filter and the screws securing the lint filter housing. Release the top panel locking clips with a putty knife and lift the top panel. Disconnect the door switch harness and remove the front panel to access the drum and burner assembly. Locate the flame switch mounted on the burner assembly — it is positioned to detect the flame produced once the igniter lights the gas. Photograph the wire connections before disconnecting. Disconnect the wires from the old flame switch, remove the mounting screw, and pull the switch free. Install the new 17438200000160 flame switch in the same position, secure the mounting screw, and reconnect the wires. Reassemble the front panel, drum, and top panel in reverse order. Restore gas and power, and run a test heat cycle to confirm the burner ignites and stays lit normally. Tools needed: Phillips screwdriver, putty knife, work gloves. Frequently Asked Questions What does the flame switch do, and how is it different from an igniter? The igniter is the component that heats up and ignites the gas at the burner. The flame switch is a separate safety component that confirms a flame is actually present after the igniter has done its job and the gas valve has opened. If the flame switch does not detect the expected flame condition, it signals the control system to close the gas valve, stopping gas flow. This two-part system — ignition plus flame confirmation — is a standard safety design in gas dryers and gas appliances generally, ensuring gas does not continue flowing if combustion isn't actually occurring. My burner lights and then shuts off after a few seconds — is this the flame switch? Yes, this is a common symptom of a failing flame switch. If the switch is not reliably maintaining its "flame detected" signal to the control board even though the burner is genuinely lit, the system may interpret this as a flame failure and shut the gas valve as a safety precaution — causing the burner to repeatedly light and then extinguish. This short-cycling pattern during what should be a continuous heat cycle is a strong indicator that the flame switch needs replacement. Why is this called a "flame switch" rather than a "flame sensor"? Different manufacturers use different terminology for similar flame-detection safety components. On Whirlpool-family gas dryers, this type of part is typically called a "flame sensor" — a bimetal-style sensor near the igniter that closes a circuit when it senses sufficient heat. Midea's parts catalog labels this specific component the "flame switch," and it serves an analogous safety role within the Midea gas burner system: confirming the presence of a flame after ignition. The terminology differs by manufacturer, but the safety function is similar in concept. Why does this repair require opening the whole dryer cabinet? On Midea gas dryers, the flame switch is mounted directly on the burner assembly inside the dryer cabinet, which is only accessible after removing the lint filter housing, releasing the top panel, and removing the front panel. This is a more involved repair than swapping an externally accessible part, but it follows the same general gas dryer disassembly procedure used for replacing igniters, thermal fuses, and other burner-area components. Since the cabinet must be opened, it can be a good opportunity to inspect other burner components (igniter, gas valve coils) for wear at the same time. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is manufactured to match the dimensions, mounting configuration, and function of the original 17438200000160 Midea flame switch. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

5304524953 Genuine OEM Frigidaire Refrigerator Defrost Heater Assembly The 5304524953 is a Genuine OEM Frigidaire/Electrolux replacement defrost heater assembly compatible with select Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Tappan, Westinghouse, and Kenmore Frigidaire-built refrigerators and upright freezers — including the popular Frigidaire Professional 19 cu. ft. single-door models in the FPRU19F8 and FPFU19F8 series. The defrost heater is mounted near the evaporator coils and periodically activates during the dishwasher's defrost cycle to melt frost buildup that accumulates on the coils. Without functioning defrost, frost continues to build up on the evaporator until it blocks airflow — causing the refrigerator or freezer to lose cooling efficiency, run continuously, and ultimately fail to maintain set temperatures. As a Genuine OEM part manufactured by Frigidaire/Electrolux to factory specifications, the 5304524953 directly replaces 5304523833, AP6997296, PS16227227, and 4975045. Tip: when replacing the defrost heater, it's a good time to also inspect or replace the paired defrost thermostat and defrost timer/control board — these three components form the defrost system and often fail in sequence. Addressing them together saves a future repair. Installs in 30–45 minutes with basic hand tools. Quick Answer The 5304524953 Genuine OEM Frigidaire Refrigerator Defrost Heater Assembly fixes Frigidaire and related-brand refrigerators and upright freezers with excessive frost or ice buildup on the evaporator coils, freezer or fresh food section too warm, refrigerator running continuously, or food spoiling faster than normal. Genuine OEM. Replaces 5304523833, AP6997296, PS16227227, 4975045. Compatible with Frigidaire Professional FPRU19F8WF0/WF2/WF3/WF4/WF5 and FPFU19F8WF2/WF4/WF5 series, plus Crosley, Electrolux, Gibson, Kelvinator, Tappan, Westinghouse, and Kenmore Frigidaire-built models. Often paired with defrost thermostat replacement. Common Problems This Part Fixes Excessive frost or ice buildup on the evaporator coils Freezer section too warm — evaporator coils iced over and blocking airflow Refrigerator section too warm — cold air not circulating because coils are frosted Refrigerator/freezer running continuously without reaching set temperature Food spoiling faster than normal due to inadequate cooling Visible ice sheet on the rear interior wall of the freezer compartment Defrost heater visibly burned through, broken, or showing arcing damage Multimeter continuity test on the heater shows an open circuit (no continuity) Replaces Part Numbers This defrost heater assembly directly replaces the following OEM and cross-reference part numbers: 5304524953, 5304523833, 140223390018, 4975045, AFR19119, AP6997296, EAP16227227, PD00083605, PS16227227. 5304524953 is the current production part superseding 5304523833. Contact our support team with your model number if you need confirmation before ordering. Compatibility This defrost heater assembly is compatible with select refrigerators and upright freezers from the following brands: Frigidaire Professional refrigerators — FPRU19F8WF0, FPRU19F8WF2, FPRU19F8WF3, FPRU19F8WF4, FPRU19F8WF5 series (19 cu. ft. single-door) Frigidaire Professional upright freezers — FPFU19F8WF2, FPFU19F8WF4, FPFU19F8WF5 series Frigidaire refrigerators — FPRU19F7WF0 and related FPRU/FPFU series models Electrolux refrigerators and freezers — select Frigidaire-platform models Crosley refrigerators (select Frigidaire-built models) Gibson refrigerators (select models) Kelvinator refrigerators (select models) Tappan refrigerators (select models) Westinghouse refrigerators (select models) Kenmore / Sears refrigerators (select Frigidaire-built models) White-Westinghouse refrigerators (select models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Genuine OEM part manufactured by Frigidaire/Electrolux to factory specifications — guaranteed fit and performance Defrost heater assembly — periodically melts frost buildup on the evaporator coils to maintain proper airflow and cooling efficiency Direct factory-original replacement — no modifications required Current production part — directly supersedes 5304523833 Replaces AP6997296, PS16227227, and 4975045 (plus 5304523833) Compatible with Frigidaire Professional FPRU19F8 and FPFU19F8 series, plus Electrolux, Crosley, Gibson, Kelvinator, Tappan, Westinghouse, White-Westinghouse, and Kenmore Frigidaire-built refrigerators and upright freezers Often replaced together with the defrost thermostat and defrost timer/control board as a paired defrost-system repair DIY repair — installs in 30–45 minutes with basic hand tools Product Specifications Part Number 5304524953 Supersedes 5304523833 Part Type Refrigerator/Freezer Defrost Heater Assembly Condition Genuine OEM Application Refrigerators and Upright Freezers (Frigidaire/Electrolux platform) Location Mounted near the evaporator coils Approximate Weight 1.60 lbs Often Paired With Defrost Thermostat, Defrost Timer/Control Board Compatible Brands Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Tappan, Westinghouse, White-Westinghouse, Kenmore Installation Notes ⚠️ Unplug Refrigerator and Move Perishable Food Before Starting — Don't Touch Heater with Bare Hands Unplug the refrigerator and safely store any food that could spoil while the power is off. Wear work gloves and safety glasses to protect your hands and eyes. Handle the new heater only by its mounting brackets or end terminals — do NOT touch the heating element directly with bare fingers; skin oils can cause hot spots and shorten the heater's life. The defrost heater is mounted near the evaporator coils, behind the rear interior access panel of the freezer compartment. Remove all freezer shelves, drawers, and the ice maker (if equipped) to clear access. If there's a heavy ice sheet covering the back wall, allow the freezer to thaw completely or carefully manually defrost the coils before continuing — never break ice off the coils, as this damages the aluminum fins. Once the area is clear, remove the screws securing the rear access panel and lift it away to expose the evaporator coils and the defrost heater. Photograph the wire connections and heater orientation before disconnecting. Disconnect the wire harness connectors from the old heater, release the heater from its mounting clips or brackets, and lift it out. Install the new 5304524953 heater in the same position, ensuring it's properly seated in the mounting brackets, and reconnect the wire harness. While the panel is open, inspect the defrost thermostat for damage — if it's brittle, discolored, or shows visible defects, this is the ideal time to replace it as well. Reinstall the rear access panel, shelves, drawers, and ice maker. Plug the refrigerator back in and allow several hours for the unit to return to its set temperature before reloading with food. Tools needed: Phillips screwdriver, 1/4" nut driver, work gloves, safety glasses. Frequently Asked Questions How do I know if the defrost heater has failed? The most reliable sign is heavy frost or ice buildup on the evaporator coils behind the freezer back panel — when the heater can't melt the frost as designed, ice accumulates until it blocks airflow and cooling efficiency drops. You may also notice the freezer or fresh food section running warm, the compressor running continuously, or food spoiling faster than normal. To confirm with the refrigerator unplugged: remove the rear freezer access panel, disconnect the heater's wire harness, and test the heater's terminals with a multimeter set to continuity mode. A working heater shows continuity (low resistance); a failed heater shows an open circuit (infinite resistance). If you measure no continuity, the heater has burned out and needs replacement. Should I replace the defrost thermostat and timer at the same time? Yes, it's strongly recommended. The defrost heater, defrost thermostat, and defrost timer/control board work together as a system — the timer (or control board on newer models) initiates the defrost cycle, the thermostat monitors the temperature at the coils and terminates the cycle when the coils are above freezing, and the heater provides the heat that melts the frost. When one component fails, the others have typically experienced similar age and stress, and a near-term failure of another defrost component is common. Since the rear access panel must already be off and the components are right next to each other, replacing all three in a single session prevents a repeat repair down the road. Should I manually defrost my freezer before installing the new heater? If there's significant ice buildup on the evaporator coils or rear wall, yes — you need to clear it before installing the new heater. Leave the freezer empty and unplugged with the door open for 12–24 hours (or longer for heavy ice) to let everything thaw naturally. Place towels at the base to catch melt water. Do NOT chip or pry ice off the evaporator coils with any tool — the aluminum fins damage easily and a damaged coil is a far more expensive repair. Once everything is fully thawed and dried, you can proceed with the heater replacement. My refrigerator/freezer has multiple defrost heater-related part numbers — which one do I need? Frigidaire/Electrolux uses different defrost heater part numbers across different generations and models. The 5304524953 is specifically used in the Frigidaire Professional 19 cu. ft. single-door FPRU19F8 series refrigerators and FPFU19F8 series upright freezers, plus a smaller set of related Frigidaire-platform models. Before ordering, confirm your refrigerator or freezer's model number is in the compatibility list above, or check your appliance's parts diagram to verify that 5304524953 (or one of its cross-references 5304523833, AP6997296, PS16227227, 4975045) is the correct part for your specific model. If your unit is a side-by-side, French door, or other style, you may need a different defrost heater. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Frigidaire/Electrolux to factory specifications. It is the exact same defrost heater assembly installed in compatible Frigidaire, Electrolux, Crosley, Gibson, Kelvinator, Tappan, Westinghouse, White-Westinghouse, and Kenmore Frigidaire-built refrigerators and freezers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

242252702 Genuine OEM Frigidaire Refrigerator Water Valve The 242252702 is a genuine Frigidaire OEM triple-solenoid water inlet valve assembly for Frigidaire, Electrolux, Kenmore, Crosley, and White-Westinghouse side-by-side refrigerators. This valve is the central control point where your home's water supply connects to the refrigerator, and it manages water flow to both the ice maker and the door-mounted water dispenser through three separate solenoids housed in one assembly, each opening independently depending on what's being called for. Rated 120V, 50/60Hz per solenoid (20W maroon, 20W yellow, 35W green — each solenoid's wire is color-coded), this valve has 4 outlets total: one 1/4" tube inlet, three 5/16" tube outlets, and one 1/4" tube outlet. It measures approximately 7-1/8"L x 3-3/4"W x 3-1/4"H and ships as a complete assembly with mounting bracket and installation instructions. This valve directly replaces the older 241734302 design and uses updated quick-connect fittings in place of the older screw-on style. A failing valve typically shows up as the ice maker or dispenser not working, slow water flow, or — notably — an overflowing ice maker caused by the valve not shutting off completely if household water pressure is too low. It directly replaces 240321801, 240505101, 240505102, 240508101, 240508102, 240531101, 241734301, 241734302, 7241734301, WV2702, 2692163, AP5671757, EAP7784018, PD00000153, PS7784018, and K-76150. Quick Answer The 242252702 Genuine OEM Frigidaire Refrigerator Water Valve fixes Frigidaire, Electrolux, Kenmore, Crosley, and White-Westinghouse side-by-side refrigerators where the ice maker or water dispenser isn't working, water flow is slow, or the ice maker is overflowing. Triple-solenoid, 4-outlet valve assembly with bracket. Replaces 240321801, 240505101, 240505102, 240508101, 240508102, 240531101, 241734301, 241734302, 7241734301, WV2702, 2692163, AP5671757, EAP7784018, PD00000153, PS7784018, K-76150. This valve needs at least 20 psi of household water pressure to shut off completely — if pressure is too low, the valve can leak and cause the ice maker to overflow even when the valve itself is functioning correctly. Common Problems This Part Fixes Ice maker has stopped making ice, or is producing less ice than usual Water dispenser on the refrigerator door isn't working or has slowed down Ice maker overflowing or leaking Slow water flow at the dispenser Water leaking near the valve at the back of the refrigerator Error code related to the water system displayed on some models Cracked or physically damaged valve housing Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This refrigerator water valve directly replaces the following OEM and cross-reference part numbers: 242252702, 240321801, 240505101, 240505102, 240508101, 240508102, 240531101, 241734301, 241734302, 2692163, 7241734301, PD00000153, EAP7784018, AP5671757, AFR15932, PS7784018 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water valve is compatible with select Frigidaire side-by-side refrigerators, and also fits select Electrolux, Kenmore, Crosley, and White-Westinghouse refrigerators built on the same platform, including model numbers such as: BFHS2611LM, BFHS2611LM0 BGHS2634KE0, BGHS2634KE1, BGHS2634KP0, BGHS2634KP1, BGHS2644KF0, BGHS2644KF1 FFSS2615TS0, FFSS2615TE4, FFHS2611PFEA, FFHB2750TD5, FRSS26L3AF0 FRS26H5ASB4, FRS26H5ASB5, FRS26H5ASB8, FRS26H5ASBA, FRS26R2AW6, FRS26R4AW5, FRS26R4CB1, FRS26RLECS0, FRS26LF7DS7 FRS6LR5EB3, FRS6LR5EB6, FRS6LR5EM2, FRS6LR5EM8, FRS6R5ESB4 PLHS69EESS2, PLHS69EGSS1, PLHS269ZCB4, PHSC39EGSS0 Crosley CRSE234FB2 Note: This valve's fitting style has been updated to quick-connect fittings, replacing the older screw-on style used on some earlier units — this may cause the appearance to differ slightly from your original part, but it is a correct functional replacement. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine Frigidaire OEM part — factory-specified solenoid design and flow-rate calibration Triple-solenoid assembly supplies water to both the ice maker and door water dispenser Resolves "ice maker not working," "dispenser not working," "slow water flow," and "ice maker overflowing" symptoms Color-coded solenoid wiring (maroon, yellow, green) for straightforward reconnection 4 outlets: 1x 1/4" tube inlet, 3x 5/16" tube outlets, 1x 1/4" tube outlet Updated quick-connect fittings for easier installation than older screw-on designs Ships complete with mounting bracket and installation instructions Replaces the full cross-reference list above, including the older 241734302 design Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number 242252702 Part Type Refrigerator Water Inlet Valve (Triple Solenoid) Condition Genuine OEM Brand Frigidaire Application Side-by-Side Refrigerators Voltage 120V per solenoid Frequency 50/60 Hz per solenoid Wattage 20W (maroon), 20W (yellow), 35W (green) Outlets 1x 1/4" tube inlet, 3x 5/16" tube outlets, 1x 1/4" tube outlet Dimensions 7-1/8"L x 3-3/4"W x 3-1/4"H Weight Approx. 1.08 lbs. Minimum Water Pressure 20 psi (required to shut off fully) Kit Contents Valve assembly, mounting bracket, installation instructions Color Gray / Blue / Green / Yellow / Maroon Material Plastic / Metal Quantity 1 valve assembly Compatible Brands Frigidaire, Electrolux, Kenmore, Crosley, White-Westinghouse Installation Notes ⚠️ Unplug Refrigerator And Shut Off Water Supply Before Starting Disconnect power at the outlet and shut off the water supply before beginning. Wear work gloves. Pull the refrigerator away from the wall for access, then locate the valve at the rear of the cabinet. Remove the two hex screws securing the old valve. Before disconnecting anything, note or photograph which plastic tube connects to which port on the multi-port valve assembly — with three solenoids and multiple outlets, getting a hose on the wrong port will send water to the wrong place. Disconnect the water supply hose, the electrical connectors (which are color-coded to their matching solenoids on the new valve), and the outlet hoses, then remove the old valve. Install the new 242252702 in the same position with its included mounting bracket, secure it with the hex screws, and reconnect each outlet hose to its correct port exactly as noted. Reconnect the color-coded electrical connectors to their matching solenoid wires. Reattach the water supply hose, tightening securely. While the back of the refrigerator is accessible, it's also a good opportunity to clean the condenser coils and surrounding area. Restore the water supply and check every connection for leaks before restoring power. Push the refrigerator back into place, then test both the ice maker and water dispenser over the following day. Tools needed: hex screwdriver or nut driver, pliers, work gloves. Frequently Asked Questions My ice maker is overflowing. Is this the valve? Possibly, but check your household water pressure first. This valve requires a minimum of 20 psi to shut off fully — if your home's water pressure is below that, the valve may not close completely even though it's functioning correctly, letting water leak through and overflow the ice maker. If your water pressure tests below 20 psi, that's the underlying cause rather than a defective valve, and addressing the pressure issue (or installing a pressure-boosting solution) is the correct fix. The new valve looks different from my old one. Is that normal? Yes. This valve has been updated to use quick-connect fittings in place of the older screw-on style used on earlier units, so the connection points may look different from what you're used to. It's still a correct, direct functional replacement — the new fittings just make installation somewhat easier. How do I know which hose goes where? This valve has multiple outlets. Note or photograph the hose routing on your old valve before disconnecting anything — with three solenoids and four total outlets, it's easy to reverse a connection if you're not careful. The electrical connectors are color-coded (maroon, yellow, green) to help you match them to the correct solenoid on the new valve, which makes the wiring side more foolproof than the hose routing. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Frigidaire to factory specifications — guaranteed fit, materials, and performance. It matches the original triple-solenoid design, wattage per solenoid, and outlet configuration of the water valve originally installed in your refrigerator. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WR57X30890 Refrigerator Genuine Water Valve Water inlet valve assembly with Wire Harness Replaces Part Numbers: WR57X30890, WR57X26569, WR57X30891, AP6891693, PS12727426. Description: This water inlet valve is a Genuine OEM part for select GE Refrigerator models, responsible for controlling the flow of water into the refrigerator's ice maker and water dispenser. It is typically located at the back of the appliance, near the water supply line. The water inlet valve features quick-connect fittings for easy installation and ensures a reliable and steady supply of water for ice production and dispensing.  

Read more less

WR60X10062 Refrigerator Air Damper Assembly Replaces Part Numbers:WR60X10062, 914163, AH304650, EA304650, AP3184950, PS304650.    California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less