Search results for "filter housing"

XPARTCO 341241 Dryer Drum Belt The XPARTCO 341241 is an aftermarket replacement dryer drum belt compatible with a wide range of Whirlpool-family dryers including Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Admiral, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, Norge, Modern Maid, Hardwick, Caloric, and Ikea. The drum belt wraps around the outside of the dryer drum, loops around the motor pulley and idler pulley, and drives the drum to rotate during every drying cycle. Without a functioning belt, the drum cannot spin and clothes will not tumble or dry. Made from high-strength rubber with reinforced ribs, this belt measures 92-1/4 inches long x 1/4 inch wide and features 4 ribs and 3 grooves. It is flat on one side and ribbed on the other, and is built to resist cracking, stretching, and wear under the high heat and repeated tension cycles of daily dryer use. It also replaces some 5-rib, 4-groove belts. Installs in 30–45 minutes with basic hand tools. Quick Answer The XPARTCO 341241 Dryer Drum Belt fixes dryers where the drum is not spinning, clothes are not tumbling, or a thumping/squealing noise is coming from the dryer. Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Admiral, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, and more. Measures 92-1/4" L x 1/4" W with 4 ribs and 3 grooves. Common Problems This Part Fixes Dryer drum not spinning — motor runs but drum stays still Clothes not tumbling during the drying cycle Thumping, squealing, or slapping noise during operation Dryer runs but produces no heat because drum is stationary Burning rubber smell coming from the dryer Visible broken or frayed belt pieces found inside the dryer cabinet Clothes taking too long to dry due to drum not rotating at correct speed Replaces Part Numbers This drum belt directly replaces the following OEM and cross-reference part numbers: 341241, 14210003, 2008, 26000341241, 26000349533, 31001026, 31531589, 3389628, 3392665, 3394651, 3399844, 341241VP, 345473, 349533, 529597, 53-0186, 53-1080, 53-1086, 53-1528, 53-1589, 53-2671, 53-2910, 660996, 660997, 661561, 693306, 694088, 694416, 694868, 695055, 697388, 8066065, 8206, 8210, 920H4, 920H5, 99906951, 99989673, 99989674, FSP341241, LB276, LB279, P46-037, P46-149, W10127457, W10131364, AH346995, AP32, EA346995, ER341241, AWP39161, PD00002263, EAP346995, 694088-NC, AP2946843, PS346995, TJ341241. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drum belt is compatible with select dryers from the following brands: Whirlpool dryers (gas and electric) Kenmore / Sears dryers (select models) Maytag dryers KitchenAid dryers Amana dryers Roper dryers Admiral dryers Jenn-Air dryers Estate dryers Magic Chef dryers Crosley dryers Inglis dryers Norge, Modern Maid, Hardwick, Caloric, and Ikea dryers Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Drives the dryer drum via the motor pulley and idler pulley for smooth, consistent tumbling every cycle 92-1/4" length x 1/4" width — 4-rib, 3-groove design; flat on one side, ribbed on the other Also replaces some 5-rib, 4-groove belts — wide cross-compatibility across Whirlpool-family models Made from high-strength rubber with reinforced ribs — resists cracking, stretching, and heat damage Direct replacement for OEM part numbers 341241 and 8066065 — no modification required Compatible with over a dozen major appliance brands built on the Whirlpool platform Aftermarket replacement built to OEM-equivalent quality standards DIY-friendly repair — installs in 30–45 minutes with basic hand tools Often replaced together with the idler pulley (691366) and drum rollers (349241T) for a complete drum drive repair Product Specifications Part Number 341241 Part Type Dryer Drum Drive Belt Condition Aftermarket Replacement Application Gas and Electric Dryers Length 92-1/4 inches Width 1/4 inch Ribs 4 ribs, 3 grooves Profile Flat on one side, ribbed on the other Material High-strength rubber with reinforced ribs Color Black Compatible Brands Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Admiral, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, Norge, Modern Maid, Hardwick, Caloric, Ikea Often Replaced With 691366 Idler Pulley, 349241T Drum Rollers Installation Notes ⚠️ Safety First — Unplug Dryer Before Starting Unplug the dryer from the power source (and shut off the gas supply for gas dryers) before beginning any repair. Remove the lint screen, then unscrew the two Phillips screws inside the lint filter housing. Use a putty knife 2 inches from each front corner to release the top panel clips and lift the top panel. Remove the front panel to access the drum. Release belt tension at the idler pulley, lift the drum slightly, and slide the old belt off. Loop the new 341241 belt around the drum with the ribbed side facing down (toward the drum). Route the belt around the idler pulley and motor pulley — consult your model's service manual or a model-specific video for the correct belt path. Reassemble and run a test cycle. Tip: While the drum is out, inspect and replace the idler pulley (691366) and drum rollers (349241T) if worn. Tools needed: Phillips screwdriver, putty knife or flat pry tool. Frequently Asked Questions How does the 341241 differ from the W10205415 and 6602-001655 belts? All three are 92-inch dryer drum belts, but they differ in width and rib count. The 341241 is 1/4" wide with 4 ribs and 3 grooves. The W10205415 is 3/8" wide with 5 ribs and 4 grooves. The 6602-001655 is 5/16" wide with 5 ribs and 4 grooves designed for Samsung dryers. Always match the part number to your specific model — do not substitute based on appearance alone. Will this belt fit my Kenmore dryer? Many Kenmore dryers — especially the popular 110-series — are manufactured by Whirlpool and use the 341241 belt. Check your model number against the compatibility list and contact our support team if you need help confirming the fit before ordering. How do I know if my drum belt needs to be replaced? The most obvious sign is that the dryer motor hums but the drum does not spin. You may also notice a thumping or slapping sound during operation, a burning rubber smell, or clothes that are damp after a full cycle. Open the dryer cabinet to visually confirm if the belt is broken, frayed, or stretched. Should I also replace the idler pulley and drum rollers? Yes — since the dryer is already disassembled, it is highly recommended to inspect and replace the idler pulley (691366) and drum support rollers (349241T) at the same time. These parts wear at a similar rate and replacing all three together — often sold as a repair kit — prevents having to disassemble the dryer again in the near future. Is this an OEM or aftermarket part? This is an aftermarket replacement built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is made from high-strength rubber to match the dimensions and performance of the original 341241 belt. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

Genuine OEM W11210463 Washer Water Inlet Valve The Genuine OEM Whirlpool W11210463 is the water inlet valve assembly for select Whirlpool, Maytag, Amana, Crosley, Admiral, Inglis and Roper washers. The valve controls the flow of hot and cold water into the washer. When it fails, the washer may not fill, may fill slowly or with too little water, or may leak. This is the original Whirlpool part, not an aftermarket equivalent. It is sold individually. Check your model number before ordering, because several similar inlet valves exist. Quick Answer The Genuine OEM W11210463 Water Inlet Valve replaces the inlet valve on a compatible washer when it has failed. Replaces W10701461, W10869803, W10883458, W11038696 and W11101906. Classic symptoms: the washer won't fill or fills slowly, leaks, or gets no hot or cold water. Common Problems This Part Fixes Washer won't fill, or fills slowly No hot or cold water Water leaking from the valve Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This water inlet valve replaces or supersedes the following part numbers: W11210463, W11038696, 4591539, W10701461, W10869803, W10883458, W11101906, AP6329219, PS12349269 If your old valve shows a different number, contact our support team and we'll check whether it matches. Compatibility This water inlet valve is listed for Whirlpool, Maytag, Amana, Crosley, Admiral, Inglis and Roper washers, including these examples: Whirlpool WTW4816FW3, NTW4516FW2, NTW4665GW0, RTW4516FW2, MVW4005SW0, ITW4871FW3, CWW3812RW0, VWW3809RW0 Maytag ATW4516HW0, NTW4516FW3 Amana NTW4516FW4, NTW4605EW1, NTW4655EW1 Crosley CAW11544EW2, CAW8350EW2 Admiral ATW4516MW0 Inglis ITW4671EW1, ITW4971EW1 Note: The models above are a sample, not a full list. Whirlpool sells similar inlet valves under other part numbers. Check your full model number against your parts diagram, or contact our support team to verify fit before ordering. Key Features Genuine OEM Whirlpool part, not an aftermarket equivalent Controls the flow of water into the washer Replaces five earlier Whirlpool valve part numbers Sold individually Product Specifications Part Number W11210463 OEM Part Number W11210463 Part Type Washer Water Inlet Valve Condition Genuine OEM Manufacturer Whirlpool Quantity 1 Valve Application Select Whirlpool-Built Washers Installation Notes ⚠️ Disconnect Power And Water Before Installing Unplug the washer and shut off the water supply before you begin, and wear work gloves. Disconnect the water hoses and the wire connectors from the old valve, noting where each goes, and remove it. Fit the new valve, reconnect the hoses and connectors, restore power and water, and check for leaks while the washer fills. Frequently Asked Questions My washer won't fill or fills slowly. Is this the part I need? It can be. Check that both water supplies are on and the hose screens are clear first, since a blocked screen can cause the same symptom. If those are fine, the inlet valve may have failed. Is this an OEM or aftermarket part? This is a genuine OEM part from Whirlpool, not an aftermarket equivalent. Does this replace my old valve number? It replaces W10701461, W10869803, W10883458, W11038696 and W11101906. If your valve shows another number, contact our support team and we'll check it. Will this fit my washer? It is listed for many Whirlpool-built models, but the model list above is only a sample. Check your full model number against your parts diagram, or contact our support team and we'll verify it before you order. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

DC97-18682D Washer Genuine Drain Hose Assembly – Compatible with Samsung Washers Product Description Maintain proper water drainage with the DC97-18682D Washer Genuine Drain Hose Assembly. This OEM replacement hose is designed to channel used water safely from your washer to the household drain system. A damaged or clogged drain hose can cause leaks, standing water, or drainage errors. Replacing it with this genuine part restores dependable washer performance and prevents messy water issues. Replaces Part Numbers DC97-18682D, DC97-18682B, DC97-18682C, DC97-18682E, PD00070138, EAP16556783, AP7018854, PS16556783. Compatibility This genuine drain hose assembly is compatible with select Samsung front-load washers. Example compatible models include (but are not limited to): Samsung WF42H5000AW, WF45K6500AW, WF56H9100AW. Always verify your washer’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Genuine OEM Replacement – Designed specifically for Samsung washers 💧 Reliable Drainage – Ensures proper water flow and prevents backup or leaks 💰 Cost-Effective Solution – Avoids costly water damage and washer breakdowns 🛠️ Easy Installation – Flexible design for quick fit with standard tools 🛡️ Fixes Common Issues – Resolves leaks, clogs, or drain-related error codes 📐 Product Specification Part Number: DC97-18682D Component Type: Washer Drain Hose Assembly Material: Heavy-duty rubber and reinforced plastic fittings Mounting: Direct fit replacement with factory connections Operating Conditions: Standard residential washer use Compliance: Genuine Samsung OEM part 🛠️ Installation Notes Tools Needed: Pliers, screwdriver (if clamps are included) ⚠️ Safety First: Always disconnect power and water supply before beginning any washer repair. Steps: Turn off water supply and unplug washer. Locate drain hose at the back of the washer. Remove hose clamps securing the old drain hose. Detach old hose from washer and household drain. Connect new DC97-18682D drain hose to washer outlet. Secure with clamps and ensure a snug fit into the drain standpipe. Restore water, reconnect power, and test for leaks. ⏱️ Time Required: 15–20 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders 🛠️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Prevent leaks and drainage problems — Add to Cart Now for a reliable, factory-approved repair!

Read more less

Genuine GE OEM Part GE WD24X25325 Dishwasher Genuine Fan Vent Assembly Genuine GE door-vent blower/fan assembly for select GE and Haier dishwashers. Product Overview The GE WD24X25325 Dishwasher Fan Vent Assembly is a genuine OEM replacement used in the dishwasher door ventilation system. The blower circulates air through the door vent during the drying portion of the cycle to help reduce retained moisture and improve drying performance. Quick Answer WD24X25325 is a Genuine GE OEM dishwasher door-vent blower/fan motor assembly. It is used on select GE and Haier dishwashers and helps move moist air through the door vent during drying. Common Problems This Part May Fix Poor drying performance Excess moisture remaining after a cycle Door vent fan does not run Unusual noise from the vent/blower area Moist air is not being exhausted through the door vent Replaces and Cross-References WD24X25325, 265D2664G005, U40G12BS3A5-51, AGE25072, AP6972063, EAP12726435, PD00073154, PS12726435. Cross-reference numbers are supplied for identification. Always verify the complete dishwasher model number before ordering. Compatibility Fits select GE and Haier dishwashers. Compatible model examples include: CDT800P2N0S1 CDT805P2N0S1 CDT845P2N3S1 DDT700SBN0TS GDF645SSN0SS GDT645SFN3DS GDT665SFN0DS GDP665SYN3FS PDT715SYN2FS PDT715SFN0DS PDP715SYN3FS QDP555SYN0FS Important: This is only a partial compatibility list. Confirm the exact dishwasher model number before purchase because similar models may use a different vent or blower assembly. Key Features Genuine GE Appliances OEM part Complete door-vent blower/fan assembly Circulates air through the dishwasher door vent Helps reduce moisture during drying For select GE and Haier dishwashers Product Specifications Manufacturer GE Appliances Manufacturer Part Number WD24X25325 Part Type Dishwasher Fan Vent / Door Vent Blower Assembly Condition New Part Quality Genuine OEM Application Dishwasher Door Ventilation / Drying System Approx. Shipping Weight 0.5 lb Installation Notes Disconnect electrical power to the dishwasher at the breaker before service. Access the door vent assembly according to the appliance service procedure. Disconnect the wiring connector carefully before removing the old fan assembly. Transfer or reuse any hardware only as directed for the specific model. Confirm the vent path is clear and the new assembly is fully seated before reassembly. Diagnostic note: Poor drying can also result from rinse-aid settings, heating-system faults, blocked vent passages, or control issues. Confirm the fan assembly is defective before replacing it. Frequently Asked Questions Is WD24X25325 a Genuine GE OEM part? Yes. GE Appliances identifies WD24X25325 as a genuine replacement fan vent assembly. What does this fan assembly do? It circulates air through the dishwasher door vent to help reduce moisture during the drying stage. Does it fit every GE dishwasher? No. It fits specific GE and Haier models. Verify the complete model number before ordering. Is this only the fan motor? This listing is for the complete WD24X25325 fan vent / door-vent blower assembly as supplied by GE. Shop With Confidence Use your dishwasher's complete model number to confirm fitment before purchase. Genuine GE OEMFan Vent AssemblyModel Verification RecommendedFast U.S. Shipping

Read more less

XPARTCO WR51X10055 Refrigerator Defrost Heater Assembly The XPARTCO WR51X10055 is an aftermarket replacement refrigerator defrost heater and bracket assembly compatible with a wide range of GE, Hotpoint, Kenmore, Haier, Americana, Monogram, and Café refrigerators. The defrost heater is a glass quartz tube heater mounted on a bracket below the evaporator coils in the freezer compartment. During each automatic defrost cycle, the heater energizes and melts any frost that has accumulated on the evaporator coils — maintaining unobstructed airflow through the coils so the refrigerator can cool efficiently. When the heater fails, frost accumulates on the coils unchecked, blocking airflow and causing both the freezer and fresh food sections to gradually warm up. Rated at 120V, 725W, this single quartz tube heater assembly measures 12-1/8" L x 3-3/8" W x 2-1/8" H and includes the heater element and mounting bracket. It directly replaces WR51X10030, AP3183311, 914088, AH303781, EA303781, PS303781, SH323, and EAP303781. Often replaced together with the defrost thermostat (WR50X10068) and temperature sensor (WR55X10025) for a complete defrost system repair. Installs in 20–30 minutes with basic hand tools. Quick Answer The XPARTCO WR51X10055 Refrigerator Defrost Heater Assembly fixes GE and Hotpoint refrigerators where frost is building up on the evaporator coils, the freezer is too warm, the fresh food section is warming up, or the refrigerator is running continuously without cooling properly. Single quartz tube heater, 120V / 725W. Assembly measures 12-1/8" L x 3-3/8" W x 2-1/8" H. Includes heater and bracket. Replaces WR51X10030, AP3183311, 914088, SH323, and more. Compatible with GE, Hotpoint, Kenmore, Haier, Americana, Monogram, and Café. Common Problems This Part Fixes Frost or ice buildup covering the evaporator coils in the freezer compartment Freezer section warming up or not maintaining set temperature Fresh food section warming up even though the freezer is running Refrigerator running continuously but not cooling properly Visible frost accumulation on the freezer back wall behind the panel Defrost heater element visibly burned out, broken, or dark/charred at the ends Both compartments gradually warming up after working normally for years Replaces Part Numbers This defrost heater assembly directly replaces the following OEM and cross-reference part numbers: WR51X10055, WR51X10030, 914088, AGE29323, AH303781, AP3183311, EA303781, EAP303781, PD00001004, PS303781. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This defrost heater is compatible with select refrigerators from the following brands: GE refrigerators (side-by-side, French door, top-freezer, and bottom-freezer) Hotpoint refrigerators Kenmore / Sears refrigerators (select GE-built models) Haier refrigerators (select GE-platform models) Americana refrigerators Monogram refrigerators Café refrigerators Tip: When replacing the defrost heater, it is highly recommended to also replace the defrost thermostat (WR50X10068) and temperature sensor (WR55X10025) at the same time. These three parts form the defrost system and are commonly replaced together — replacing all three prevents a second disassembly if another component fails soon after. Key Features Single quartz tube glass heater — melts frost from the evaporator coils during each automatic defrost cycle, maintaining airflow and cooling efficiency Rated 120V / 725W — correct electrical specifications for compatible GE refrigerators Assembly dimensions: 12-1/8" L x 3-3/8" W x 2-1/8" H — direct fit into the evaporator coil bracket Includes heater element and mounting bracket — complete assembly ready to install Replaces WR51X10030 and WR51X10055 — both older and current part numbers covered Compatible with GE, Hotpoint, Kenmore, Haier, Americana, Monogram, and Café refrigerators Often replaced together with WR50X10068 defrost thermostat and WR55X10025 temperature sensor Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 20–30 minutes with basic hand tools Product Specifications Part Number WR51X10055 Also Replaces WR51X10030 Part Type Refrigerator Defrost Heater and Bracket Assembly Condition Aftermarket Replacement Heater Type Single quartz tube glass heater Voltage 120V AC Wattage 725W Dimensions 12-1/8" L x 3-3/8" W x 2-1/8" H Includes Heater element and mounting bracket Often Replaced With WR50X10068 Defrost Thermostat, WR55X10025 Temperature Sensor Compatible Brands GE, Hotpoint, Kenmore, Haier, Americana, Monogram, Café Installation Notes ⚠️ Unplug Refrigerator Before Starting — Wear Work Gloves Unplug the refrigerator before beginning. Remove all food and shelving from the freezer compartment. Remove the freezer bottom drawer and the back panel screws (typically 2 hex-head screws). Slide out the back panel to expose the evaporator coils and defrost heater assembly. If the coils are covered in frost or ice, use a hair dryer to melt the ice before removing the heater — do not chip or force the heater free while iced over, as the glass element is fragile and will break. Disconnect the heater wires from the wiring harness — note the orientation before disconnecting. Remove the 2 Phillips screws securing the heater bracket and lift the heater assembly out. Install the new WR51X10055 heater assembly in the same position, reconnect the wires, and reinstall the bracket screws. Reinstall the back panel, shelving, and food. Restore power and verify the defrost cycle operates normally. Wear work gloves throughout — the evaporator area has sharp edges. Tools needed: Phillips screwdriver, 1/4" nut driver, hair dryer (if coils are iced over), work gloves. Frequently Asked Questions What does the refrigerator defrost heater do? Modern refrigerators use an automatic defrost system that periodically runs a defrost cycle — typically once or twice a day — to melt frost that accumulates on the evaporator coils during normal operation. The defrost heater is a glass quartz heating element that energizes during this cycle and melts the frost off the coils. This keeps the coils clear so air can flow freely through them to cool the refrigerator. When the heater fails, frost builds up unchecked on the coils over days or weeks — eventually blocking airflow completely and causing both compartments to warm up, even though the compressor is still running. How do I know if my defrost heater has failed? Remove the freezer back panel to expose the evaporator coils. If the coils are heavily coated in frost or solid ice — especially if both the freezer and refrigerator sections have been warming up — a failed defrost heater is the most likely cause. You can confirm with a multimeter: disconnect the heater and probe both wire ends. A working heater shows continuity (resistance between approximately 10–200 ohms at room temperature depending on wattage). No continuity confirms the heater element has burned out. Also visually inspect the glass tube — a burned, blackened, or broken tube is a clear sign of failure. Should I also replace the defrost thermostat and temperature sensor? Yes — since the freezer must be fully emptied and the back panel removed to replace the heater, it is highly recommended to also replace the defrost thermostat (WR50X10068) and temperature sensor (WR55X10025) at the same time. All three components form the defrost system and wear at similar rates. A failed thermostat or sensor can cause the heater to run too long or not at all — replacing all three in a single repair eliminates that risk and saves you from another complete freezer teardown in the near future. My freezer is warming up but the compressor is running — is it the defrost heater? It often is — but not always. A compressor that is running but not cooling can be caused by a failed defrost heater (frost blocking airflow), a faulty evaporator fan motor (air not circulating), a defrost thermostat or timer failure, or a sealed system problem (refrigerant leak or compressor issue). The easiest way to distinguish a defrost system failure from other causes is to open the freezer and check whether frost has built up on the back panel or coils. If yes, the defrost heater is the most likely culprit. If the coils are clear and the compressor is running, look at the evaporator fan or sealed system next. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured as a single quartz tube glass heater rated at 120V/725W to match the dimensions and performance of the original WR51X10055 defrost heater assembly. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

5215ER2002G Washer Genuine OEM Drain Hose Assembly Product Overview The 5215ER2002G Washer Genuine OEM Drain Hose Assembly is designed to carry wastewater from the washer tub to the household drain. This OEM drain hose ensures proper water flow and prevents leaks, helping your washer drain efficiently and reliably. Flexible drain hose assembly that carries wastewater from your washer to the household drain. Replace if cracked, leaking, or damaged during installation. Quick Answer If your washer is not draining, leaking from the back, or showing drain errors, the 5215ER2002G drain hose may be clogged, cracked, or damaged. Replacing it restores proper drainage and prevents leaks. Replaces Part Numbers Replaces OEM part number: 5215ER2002G, AEM73773301, 5215ER2002Q, 1268108, 4932ER3008A, 5215ER2002B, 5215ER2002C, 5215ER2002D, 5215ER2002E, 5215ER2002F, 5215ER2002N, 5215ER2002R, 5215ER2002S, 5215ER2002Y, AEM75033801, AGM75511501, ALG51596, PD00005676, 095225452741, AH3527325, EA3527325, AP4457291, PS3527325. Compatibility This drain hose assembly is compatible with select LG and compatible front-load washers. LG Front-Load Washers Kenmore (LG-built) Washers Always verify your washer’s model number before ordering. Contact our support team if you’re unsure. Common Problems This Part Fixes Washer not draining Water leaking from hose or rear panel Drain errors or slow drainage Cracked, kinked, or clogged hose Key Features Genuine OEM drain hose assembly Ensures proper wastewater flow Leak-resistant construction Exact-fit replacement for compatible models Product Specifications Part Number: 5215ER2002G Part Type: Washer Drain Hose Assembly Brand: LG Condition: New OEM / Aftermarket: Genuine OEM Application: Front-Load Washers Troubleshooting Guide Water won’t drain → Possible blockage or damaged hose Leak at back of washer → Cracked or loose drain hose Slow draining → Kinked or partially clogged hose When Should You Replace This Hose? Replace this hose if you notice leaks, visible damage, or if your washer is not draining properly. Installation Notes ⚠️ Disconnect power and water supply before installation. Remove clamps, detach the old hose, and install the new hose securely to prevent leaks. Related Parts Washer Drain Pump Drain Pump Filter Water Inlet Valve Frequently Asked Questions Will this hose fit my washer?This hose fits select LG and compatible washers. Always verify your model number. What does a drain hose do?It carries wastewater from the washer to the household drain. What are signs of a bad hose?Leaks, cracks, kinks, or drainage issues indicate replacement is needed. Is this OEM?Yes, this is a genuine OEM drain hose assembly. Shop With Confidence Parts-O-Matic is a U.S.-based appliance parts retailer specializing in OEM and high-quality replacement parts. We offer fast shipping, reliable products, and expert support. Fast Shipping Genuine OEM Parts Compatibility Support  

Read more less

XPARTCO Washer Replacement Part XPARTCO 5220FR2075V Washer Water Valve Replaces 5221ER1003M Three-solenoid, DC12V water inlet valve assembly for select LG-built front-load washing machines. Product Overview The XPARTCO 5220FR2075V Washer Water Inlet Valve controls the flow of water entering compatible front-load washing machines. When energized by the washer control, the valve opens the required water path and directs water through the dispenser and into the tub. This is a new XPARTCO aftermarket replacement part designed to replace compatible LG inlet valve assemblies, including part number 5221ER1003M. Quick Answer XPARTCO 5220FR2075V is a three-solenoid, DC12V washer water inlet valve for select LG and LG-built Kenmore front-load washers. It replaces 5221ER1003M. Verify the complete washer model number, valve configuration, electrical connectors, and hose outlets before ordering. Common Problems This Part May Fix Washer does not fill with water Slow or restricted water filling Water continues entering after the washer is turned off Leaking from the inlet-valve area Incorrect water flow through the dispenser IE or another water-inlet-related error One or more valve solenoids do not open Replaces and Cross-References 5220FR2075V, ALG312873, AP7003066, PD00074485, PS16544738, 5221ER1003M, AP6334246, 4869495, ALG51888, EAP12579227, PD00050119, PS12579227 Cross-reference numbers help identify the compatible component. XPARTCO is an aftermarket replacement brand and is not manufactured by LG. Compatibility Designed for select LG and LG-built Kenmore front-load washers that specify 5220FR2075V, 5221ER1003M, or an approved equivalent. Compatible model examples associated with this valve family.  Important: This is only a partial compatibility list. LG water valves can look nearly identical while using different voltages, solenoid counts, mounting tabs, connectors, or outlet arrangements. Confirm the full washer model and original valve number before purchase. Key Features High-quality XPARTCO aftermarket replacement Replaces LG valve number 5221ER1003M DC12V, Three-solenoid inlet valve design Controls water entering the washer Directs water through the dispenser system Threaded inlet connection for the supply hose Designed for select LG-built front-load washers Product Specifications XPARTCO Part Number 5220FR2075V Replaces 5221ER1003M Brand XPARTCO Part Type Washer Water Inlet Valve Assembly, DC12V, 3 solenoid. Condition New Part Quality Aftermarket Replacement Valve Configuration Three Solenoids, DC12V Application Front-Load Washing Machine Included One Water Inlet Valve Assembly Installation Notes Unplug the washer and close both water-supply valves. Disconnect the inlet hose and prepare for residual water. Remove the washer top panel according to the appliance service procedure. Photograph the electrical connectors and outlet-hose locations before disconnecting them. Release the wire connectors, hose clamps, and mounting screws from the original valve. Install the replacement valve in the same orientation and reconnect every hose and wire. Open the water supplies slowly, check for leaks, restore power, and test the washer. Diagnostic tip: Confirm that the household water valves are open, inlet hoses are not kinked, and the inlet screens are not clogged before replacing the valve. Frequently Asked Questions Is XPARTCO 5220FR2075V a Genuine OEM LG part? No. It is an XPARTCO aftermarket replacement designed for compatible LG-built washers. What does the water inlet valve do? It opens and closes electrically to control water entering the washer and directs water through the dispenser system. Does this valve replace 5221ER1003M? Yes, this XPARTCO valve is sold as a replacement for 5221ER1003M on compatible washer models. Can a bad inlet valve cause an IE error? Yes. A failed solenoid, restricted valve, clogged inlet screen, or water-supply problem can cause slow filling or an inlet-related error. Will this fit every LG washer? No. Confirm the complete model number and compare the original valve number, connectors, mounting points, and hose outlets before ordering. Shop With Confidence Verify your washer model and original valve number before ordering. Our compatibility support team can help determine whether XPARTCO 5220FR2075V is correct for your appliance. XPARTCO Replacement PartFast U.S. ShippingCompatibility SupportSecure Checkout

Read more less

5304524452 Washer Genuine OEM Drain Pump Assembly The 5304524452 is a genuine Frigidaire OEM drain pump assembly for Frigidaire stacked laundry center (washer/dryer combo) units, and also fits select Crosley, Electrolux, Gibson, Kelvinator, Westinghouse, and Kenmore models. This pump removes wash water from the tub at the end of each cycle, draining it out before the washer refills with fresh water for rinses. Common causes of a failing pump include normal wear and tear over time, an obstructed drain line, or issues with the pump housing or impeller. Symptoms of a bad pump assembly include incomplete draining of water at the end of cycles, water pooling in the tub, or the washer failing to advance through its cycle because it can't clear the water. It directly replaces 4246239, 4839543, 4959972, 5304500535, 5304515673, A03077601, AP5962219, AP6333076, AFR19009, AP6989734, BPX401-13J, EAP11703882, EAP12365991, EAP16218540, PD00063454, PS16218540. Quick Answer The 5304524452 Washer Genuine OEM Drain Pump Assembly fixes Frigidaire, Crosley, Electrolux, Gibson, Kelvinator, Westinghouse, and Kenmore stacked laundry center units where the washer won't drain, water pools in the tub, or the cycle won't advance past the drain step. Replaces 4246239, 4839543, 4959972, 5304500535, 5304515673, A03077601, AP5962219, AP6333076, AFR19009, AP6989734, BPX401-13J, EAP11703882, EAP12365991, EAP16218540, PD00063454, PS16218540. Several sources note that some replacement drain pumps look similar to this one but aren't the same part — check your original pump's model number or your washing machine's model number carefully before ordering. Common Problems This Part Fixes Washer not draining at the end of a cycle Water pooling or standing in the tub after a completed cycle Washer failing to advance past the drain step Incomplete draining leaving damp or soaked clothes Pump making unusual noise from a damaged impeller Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer drain pump assembly directly replaces the following OEM and cross-reference part numbers: 5304524452, 4246239, 4839543, 4959972, 5304500535, 5304515673, A03077601, AP5962219, AP6333076, AFR19009, AP6989734, BPX401-13J, EAP11703882, EAP12365991, EAP16218540, PD00063454, PS16218540 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drain pump assembly is compatible with select Frigidaire stacked laundry center units, and also fits select Crosley, Electrolux, Gibson, Kelvinator, Westinghouse, and Kenmore combo units built on the same platform, including model numbers such as CFLE3900UW0, CFLE3900UW1, CFLE3900UW3, FFLE3900UW0, FFLE3900UW1, FFLE3900UW2, FFLE3900UW3, FFLE3911QW0, FFLE3911QW1, FFLE39C1QW0, FFLE4033QT0, FFLE4033QW0, FFLE40C3QT0, FFLE40C3QW0, FFLG3900UW0, FFLG3900UW1, FFLG3900UW2, FFLG3900UW5, FFLG3911QW0, FFLG3911QW1, FFLG3911QW2, FFLG4033QT0, FFLG4033QT1, FFLG4033QW0, FFLG4033QW1, SFLG3911RW0, SFLG3911RW1, SFLG4033RT0, SFLG4033RT1, SFLG4033RW0, SFLG4033RW1, and Kenmore 417.61712510, 417.61712511, 417.61722510, 417.61723510, 417.61732810, 417.61733810, 417.71712510, 417.71712511, 417.71722510, 417.71722511, 417.71723510, 417.71723511, 417.71732810, and 417.71733810. Note — similar-looking but different pumps exist: Some replacement drain pumps are visually similar to this one but aren't compatible. Check your original pump's model number or your washing machine's model number carefully before ordering. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine Frigidaire OEM part — factory-specified pump housing and impeller design Drains wash water from the tub at the end of each cycle Resolves "won't drain," "water pooling," and "won't advance past drain step" symptoms Direct drop-in replacement matching the original mounting and hose connections Replaces 4246239, 4839543, 4959972, 5304500535, 5304515673, A03077601, AP5962219, AP6333076, AFR19009, AP6989734, BPX401-13J, EAP11703882, EAP12365991, EAP16218540, PD00063454, PS16218540 Compatible with Frigidaire, Crosley, Electrolux, Gibson, Kelvinator, Westinghouse, and Kenmore laundry center units Genuine OEM replacement — guaranteed fit, materials, and performance Simple DIY repair with basic tools Product Specifications Part Number 5304524452 Part Type Washer Drain Pump Assembly Condition Genuine OEM Brand Frigidaire Application Stacked Washer/Dryer Laundry Centers Function Drains wash water from the tub at the end of each cycle Repair Difficulty Easy Quantity 1 drain pump assembly Compatible Brands Frigidaire, Crosley, Electrolux, Gibson, Kelvinator, Westinghouse, Kenmore Installation Notes ⚠️ Unplug The Laundry Center And Shut Off Water Supply Before Starting Disconnect power to the laundry center unit and shut off the water supply before beginning. Wear work gloves and have towels ready for any residual water. Access the pump, typically located at the bottom front or rear of the washer section depending on your model. Remove the clamp attaching the hose to the old pump, then remove the hose. Remove the three screws holding the pump to the washer. Take out the old pump. Install the new 5304524452 in the same position and secure it with the three mounting screws. Reattach the hose to the new pump and secure the clamp. Restore the water supply and power, then run a test cycle to confirm the washer drains completely with no leaks. Tools needed: pliers, screwdriver, work gloves. Frequently Asked Questions My washer isn't draining. Is this the part I need? Yes, this is the most direct symptom of a failed drain pump. Since this pump is responsible for removing wash water from the tub at the end of each cycle, a worn impeller or internal failure can leave water standing in the tub and prevent the washer from advancing to the next stage of the cycle. Is this a difficult repair? No, one customer described it as an easy removal and installation: remove the clamp attaching the hose to the pump, remove the hose, remove the three screws holding the pump to the washer, then reverse the process with the new pump. How do I make sure I'm ordering the correct pump, since some look similar? Check the model number printed on your original pump, or your washing machine's full model number, before ordering. Multiple sources note that some replacement drain pumps look visually similar to this one but aren't actually compatible, so matching your specific part or model number is the reliable way to confirm fit. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Frigidaire to factory specifications — guaranteed fit, materials, and performance. It matches the original pump housing, impeller, and connection type of the drain pump assembly originally installed in your washer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 17438200000160 Gas Dryer Flame Switch The XPARTCO 17438200000160 is an aftermarket replacement gas dryer flame switch compatible with select Midea, Insignia gas dryers, including the MLG45N1BWW, MLG45N3BMG, MLG45N3BWW, MLG52S7AWW, CDG41N1AW/CDG45N1AW series, NSDRE67WH8A, NSFDRG67WH8A, NSDRE67WH8AC, NSTDRG75W1. The flame switch is a safety component mounted on the burner assembly that confirms a flame is actually present after the gas valve opens and the igniter lights the burner. If the switch does not detect a flame within the expected window, it signals the control board to shut off the gas valve, preventing unburned gas from continuing to flow into the dryer cabinet. When the flame switch fails, the dryer may not heat at all, may shut off the burner shortly after ignition (short-cycling the flame), may trip a no-heat fault code on models with digital displays, or — in rarer failure modes — may fail to shut off gas flow appropriately, which is a safety-relevant failure. It directly replaces 17438200000160 (Midea OEM). Installs in 30–45 minutes with basic hand tools. Quick Answer The XPARTCO 17438200000160 Gas Dryer Flame Switch fixes Midea gas dryers that won't heat, where the burner lights and then shuts off shortly after ignition, or where a no-heat fault is displayed. Mounted on the burner assembly — confirms flame presence after ignition and signals the control board to keep the gas valve open. Genuine Midea OEM part number. Compatible with Midea MLG45N1BWW, MLG45N3BMG, MLG45N3BWW, MLG52S7AWW, CDG41N1AW, and CDG45N1AW gas dryers. Common Problems This Part Fixes Gas dryer not heating — flame switch not confirming flame presence to the control board Burner lights briefly and then shuts off — flame switch failing to maintain the "flame confirmed" signal No-heat fault code displayed on models with digital control panels Dryer runs and tumbles normally but produces no heat Burner repeatedly cycling on and off rapidly during a heat cycle Visible damage, corrosion, or carbon buildup on the flame switch near the burner Replaces Part Numbers This flame switch directly replaces the following part number: 17438200000160, AP7153000, PS18188577. This is the Midea, Insignia manufacturer part number used across multiple Midea gas dryer models. Contact our support team with your model number if you need confirmation before ordering. Compatibility This flame switch is compatible with select Midea, Insignia gas dryers, including: Midea MLG45N1BWW gas dryer Midea MLG45N3BMG gas dryer Midea MLG45N3BWW gas dryer Midea MLG52S7AWW gas dryer (8.0 cu. ft. front load) Midea CDG41N1AW gas dryer (Criterion, air vent) Midea CDG45N1AW gas dryer (Criterion, air vent) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Confirms flame presence at the burner after ignition and signals the control board accordingly Safety component — helps ensure the gas valve closes promptly if a flame is not detected Mounts directly to the burner assembly in the same position as the original switch Genuine Midea manufacturer part number — designed as a direct fit for compatible models Compatible with Midea MLG45N1BWW, MLG45N3BMG, MLG45N3BWW, MLG52S7AWW, CDG41N1AW, and CDG45N1AW gas dryers Installs in 30–45 minutes with basic hand tools Product Specifications Part Number XP17438200000160 Part Type Gas Dryer Flame Switch Condition Aftermarket Replacement Application Gas Dryers (Midea platform) Location Mounted on the burner assembly Compatible Brands Midea Installation Notes ⚠️ Gas Appliance Safety Warning This part is installed in a gas dryer. Always unplug the dryer and shut off the gas supply at the shutoff valve before beginning any repair. If you smell gas at any point during or after installation, leave the area immediately and contact your gas utility provider. Do not restore power or gas until the repair is fully complete and all connections are confirmed secure. If you are not comfortable working on gas appliances or safety-relevant flame-detection components, have this part installed by a qualified technician. ⚠️ Wear Work Gloves — Access Requires Cabinet Disassembly Disconnect power and shut off gas before beginning. Wear work gloves throughout — there are sharp metal edges inside the dryer cabinet. Remove the lint filter and the screws securing the lint filter housing. Release the top panel locking clips with a putty knife and lift the top panel. Disconnect the door switch harness and remove the front panel to access the drum and burner assembly. Locate the flame switch mounted on the burner assembly — it is positioned to detect the flame produced once the igniter lights the gas. Photograph the wire connections before disconnecting. Disconnect the wires from the old flame switch, remove the mounting screw, and pull the switch free. Install the new 17438200000160 flame switch in the same position, secure the mounting screw, and reconnect the wires. Reassemble the front panel, drum, and top panel in reverse order. Restore gas and power, and run a test heat cycle to confirm the burner ignites and stays lit normally. Tools needed: Phillips screwdriver, putty knife, work gloves. Frequently Asked Questions What does the flame switch do, and how is it different from an igniter? The igniter is the component that heats up and ignites the gas at the burner. The flame switch is a separate safety component that confirms a flame is actually present after the igniter has done its job and the gas valve has opened. If the flame switch does not detect the expected flame condition, it signals the control system to close the gas valve, stopping gas flow. This two-part system — ignition plus flame confirmation — is a standard safety design in gas dryers and gas appliances generally, ensuring gas does not continue flowing if combustion isn't actually occurring. My burner lights and then shuts off after a few seconds — is this the flame switch? Yes, this is a common symptom of a failing flame switch. If the switch is not reliably maintaining its "flame detected" signal to the control board even though the burner is genuinely lit, the system may interpret this as a flame failure and shut the gas valve as a safety precaution — causing the burner to repeatedly light and then extinguish. This short-cycling pattern during what should be a continuous heat cycle is a strong indicator that the flame switch needs replacement. Why is this called a "flame switch" rather than a "flame sensor"? Different manufacturers use different terminology for similar flame-detection safety components. On Whirlpool-family gas dryers, this type of part is typically called a "flame sensor" — a bimetal-style sensor near the igniter that closes a circuit when it senses sufficient heat. Midea's parts catalog labels this specific component the "flame switch," and it serves an analogous safety role within the Midea gas burner system: confirming the presence of a flame after ignition. The terminology differs by manufacturer, but the safety function is similar in concept. Why does this repair require opening the whole dryer cabinet? On Midea gas dryers, the flame switch is mounted directly on the burner assembly inside the dryer cabinet, which is only accessible after removing the lint filter housing, releasing the top panel, and removing the front panel. This is a more involved repair than swapping an externally accessible part, but it follows the same general gas dryer disassembly procedure used for replacing igniters, thermal fuses, and other burner-area components. Since the cabinet must be opened, it can be a good opportunity to inspect other burner components (igniter, gas valve coils) for wear at the same time. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is manufactured to match the dimensions, mounting configuration, and function of the original 17438200000160 Midea flame switch. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

W11481722 Genuine OEM Whirlpool Washer Shift Actuator The W11481722 is a genuine Whirlpool OEM shift actuator (gear case) for Whirlpool, Maytag, Amana, Crosley, and Kenmore top-load washers. Mounted at the bottom of the washer, this component does two jobs in one assembly: it physically shifts the transmission between modes by moving an arm on the cam assembly, engaging and disengaging either the basket or the agitator/washplate depending on what the cycle calls for, and it houses the tachometer that reports drum speed back to the control board throughout the cycle. Rated 120V, 60Hz, with a 6-pin wire connector for a direct plug-in fit. Because this single part handles both mechanical shifting and speed sensing, a failure here can produce a range of symptoms depending on which function is affected: the washer may fail to spin or agitate properly, get stuck in one mode without transitioning to the other, or the control board may throw an error code related to a lost tachometer signal or improper basket engagement. It directly replaces AP6990751, W10597177, WPW10597177, W11237117, W11398781. Quick Answer The W11481722 Genuine OEM Whirlpool Washer Shift Actuator fixes Whirlpool, Maytag, Amana, Crosley, and Kenmore top-load washers that won't spin or agitate properly, get stuck in one mode, or throw a tachometer/basket-engagement error code. 120V, 60Hz, 6-pin connector. Replaces AP6990751, W10597177, WPW10597177, W11237117, W11398781. This part also contains the tachometer — a single failure here can affect both cycle shifting and speed sensing at once. Common Problems This Part Fixes Washer won't spin Washer won't agitate Washer gets stuck in one mode and won't transition between agitate and spin Error code related to a tachometer signal or basket engagement Basket doesn't engage or disengage correctly during the cycle Cycle stalls partway through as the control loses accurate speed feedback Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer shift actuator directly replaces the following OEM and cross-reference part numbers: W11481722, W10597177, WPW10597177, W11237117, W11398781, AP6990751, AWP45140, EAP16221077, PD00067016, PS16221077 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This shift actuator is compatible with select Whirlpool top-load washers, and also fits select Maytag, Amana, Crosley, and Kenmore washers built on the Whirlpool platform, including model numbers such as: WTW5100HW1, WTW5100HC1, WTW6120HC1 WTW4616FW3, WTW4655JW2, WTW4715EW0, WTW4715EW2 WET4027HW2, WETLV27HW3, WGT4027HW0, WGTLV27HW0 NTW4516FW0, NTW4516FW2, NTW4516FW4, NTW4519JW2 NTW4601BQ1, NTW4605EW0, NTW4611BQ1, NTW4615EW0, NTW4631BQ1, NTW4635EW0, NTW4651BQ1, NTW4655EW0, NTW4701BQ1, NTW4705EW0, NTW4750BQ1, NTW4755EW0 Crosley VAW3584GW0, VAW3584GW1, VAW3584GW2 Kenmore 110-series models (110.xxxxx) Note: Always verify your full model number before ordering, since Whirlpool uses several different shift actuator designs across its washer lineup. Contact our support team with your model number if you're unsure. Key Features Genuine Whirlpool OEM part — factory-specified shifting mechanism and tachometer calibration Combines two functions in one assembly: transmission mode shifting and drum speed sensing Resolves "won't spin," "won't agitate," "stuck in one mode," and "tachometer error code" symptoms Rated 120V, 60Hz 6-pin connector for a direct plug-in electrical fit Direct drop-in replacement — mounts to the original gear case position Replaces W10597177, W11237117, W11398781, WPW10597177, and W10625252 Compatible with Whirlpool, Maytag, Amana, Crosley, and Kenmore top-load washers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number W11481722 Part Type Washer Shift Actuator (Gear Case) Condition Genuine OEM Brand Whirlpool Location Bottom of the washer, in the gear case Function Shifts transmission between agitate/wash and spin modes; houses the tachometer Voltage 120V Frequency 60 Hz Connector 6-pin Material Metal Repair Difficulty Moderate — gear case access required Quantity 1 shift actuator Compatible Brands Whirlpool, Maytag, Amana, Crosley, Kenmore Installation Notes ⚠️ Unplug Washer Before Starting — Note Cam Position Before Removal Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access to the shift actuator is through the gear case at the bottom of the washer, which typically requires tipping the washer back or removing surrounding panels per your model's service instructions to reach it. Photograph the wiring harness connection and the actuator's mounting position before disconnecting anything. Disconnect the 6-pin wiring harness connector from the old actuator, remove its mounting screws, and pull it free from the gear case. Install the new W11481722 in the same position, secure the mounting screws, and reconnect the 6-pin harness connector fully. Reassemble any panels removed for access, restore power, and run a full test cycle through both agitate and spin to confirm the washer shifts between modes correctly with no error codes. Tools needed: Phillips or nut driver screwdriver, work gloves. Frequently Asked Questions My washer is stuck in one mode — it will either agitate or spin, but not both. Is this the shift actuator? Yes, this is a classic symptom of a failed shift actuator. This part is what physically moves the arm on the cam assembly to switch the transmission between agitate/wash mode and spin mode. If it fails, the washer can get mechanically stuck engaging only one of those two functions, since the shifting mechanism itself is no longer moving the cam correctly. My control board shows a tachometer error. Why would that be the shift actuator and not something else? Because this single part combines both the mechanical shifting function and the tachometer that reports drum speed to the control board, a failure inside the actuator can knock out the speed-sensing function even if the shifting mechanism is unaffected, or vice versa. A tachometer-related error code is a direct signal that this component — not a separate sensor — is the likely cause. Is this a difficult repair? It's a moderate repair, since accessing the gear case at the bottom of the washer typically requires tipping the unit back or removing surrounding panels, depending on your specific model. It's within reach for a confident DIYer with basic hand tools, but budget more time than a simple top-panel swap. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original shifting mechanism, tachometer calibration, and 6-pin harness configuration of the shift actuator originally installed in your washer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

Genuine Bosch 00617090 Microwave Waveguide Cover - Compatible with Bosch Microwaves Product Description Protect your microwave with the Genuine Bosch 00617090 Microwave Waveguide Cover. This OEM waveguide cover is designed for select Bosch built-in microwaves, shielding the magnetron from food splatter and moisture to ensure safe and efficient operation. Made of silicone-bonded mica and measuring approximately 4-1/8" x 2-5/8"", it prevents arcing, sparking, or microwave failure due to a damaged cover, delivering reliable performance as an authentic Bosch part. Note: Includes one waveguide cover. Disconnect power before installation. Inspect waveguide channel for debris to ensure optimal performance. Replaces part numbers: 00617090, 12014089, PD00053143, EAP9492671, AP5806321, PS9492671. Compatibility: Compatible with models including but not limited to: Bosch: HBL5751UC/01, HBL8751UC/01, HMC80151UC/01, HMC87151UC/01, HMC80152UC/01, HMC80251UC/01, HMC80252UC/01, HMC87152UC/01, HMB50152UC/01, HMB50162UC/01, HMB57152UC/01 Thermador: (select models, verify compatibility) Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Bosch built-in microwaves. 🛡️ Specifications: OEM waveguide cover, silicone-bonded mica, approximately 4-1/8" x 2-5/8". 💪 Reliable Performance: Authentic Bosch part ensures long-lasting durability. 🛠️ Easy Installation: Requires screwdriver; typically installed in 5–10 minutes. 🔥 Effective Fixes: Prevents arcing, sparking, or microwave failure due to damaged cover. Product Specification Part Number: Genuine Bosch 00617090 Component Type: Microwave waveguide cover Material: Silicone-bonded mica Mounting: Screw-mounted or clip-in (model-dependent) Operating Conditions: Suitable for high-temperature microwave environments Compliance: Prop 65 warning for California Installation Notes: Safety First: Disconnect the microwave from the power source before installation. Shop for high-quality Genuine appliance parts with a 30-day return policy. Keep your microwave running safely today! Add to cart now for a reliable fix!

Read more less

XPARTCO W11165546 Washer Water Inlet Valve The XPARTCO W11165546 is an aftermarket replacement washer water inlet valve assembly compatible with Maytag Bravos XL, Whirlpool Cabrio, Kenmore 700-series, and related Whirlpool-platform HE top-load washers. This 4-solenoid assembly controls the flow of hot and cold water from the household supply lines into the washer tub and dispenser compartments. It includes an integrated thermistor on the center outlet that monitors incoming water temperature and communicates it to the control board so the washer can achieve the correct wash temperature. When the valve fails — or when a single solenoid coil burns out — the washer may not fill, fill too slowly, fill with the wrong temperature, overfill, or display error codes F8E1, LF, or LO FL. Rated 120V, 60Hz, with 2 inlet ports and 3 outlet ports, this assembly measures 5-3/8"L x 4-1/4"W x 3"H. The valve body may be blue or green in color depending on production run — both are functionally identical. It is compatible with 1/2" ID supply hoses. It directly replaces W10599423, W10758828, W10839828, W11096267, W11165546VP, WV5546, 33090105, 4545980, AP6284346, EAP12348013, PD00037668, and PS12348013. Installs in 15–25 minutes with basic hand tools. Quick Answer The XPARTCO W11165546 Washer Water Inlet Valve fixes Maytag Bravos XL and Whirlpool Cabrio/WTW HE top-load washers that won't fill, fill slowly, fill with wrong temperature, overfill, or display error codes F8E1, LF, or LO FL. 4-solenoid valve with thermistor. 120V/60Hz. 2 inlet / 3 outlet ports. 5-3/8"L x 4-1/4"W x 3"H. Compatible with 1/2" ID supply hoses. Replaces W10599423, W10758828, W10839828, W11096267, W11165546VP, 33090105, 4545980, AP6284346, PS12348013. Common Problems This Part Fixes Washer not filling with water — error code F8E1, LF, or LO FL displayed Washer filling very slowly — taking much longer than normal to reach water level Washer filling with only cold water on a warm or hot cycle — hot solenoid failed Washer filling with only hot water on a cold cycle — cold solenoid failed Washer overfilling or filling continuously — valve port stuck open Water temperature incorrect despite correct cycle selection — thermistor failed Water dripping into the tub between cycles — valve not closing completely Water leaking from the back of the washer near the valve Replaces Part Numbers This water inlet valve directly replaces the following OEM and cross-reference part numbers: W10839828, 33090105, 4545980, W10599423, W10758828, W11096267, W11165546VP, AP6284346, AWP43457, EAP12348013, PD00037668, PS12348013. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water inlet valve is compatible with select HE top-load washers from the following brands and series: Maytag top-load washers — Bravos XL series (MVWB765FW0, MVWB765FW1, MVWB765FW2, MVWB765FW3, MVWB765FC1, MVWB765FC2, MVWB766FW0, MVWB766FW1, MVWB835DW1, MVWB835DW2, MVWB835DW3, MVWB835DW4, MVWB855DC2, MVWB855DC3, MVWB865GC0, MVWB865GW0, MVW6230HW2, MVW7230HW0, MVW7232HW0 and related models) Whirlpool top-load washers — Cabrio / WTW series (WTW7500GC0, WTW7500GW0, WTW8500DC2, WTW8500DC4, WTW8500DC5, WTW8500DR4, WTW8500DR5, WTW8500DW4, WTW8500DW5, WTW8700EC1, 7MWTW8500EC2 and related models) Kenmore / Sears top-load washers — 700 series (11028132410, 11028132411, 11028132412, 11028132413, 11028133410, 11028133411, 11029132411, 11029133410 and related models) Crosley top-load washers (select models) Note: The valve body color may be blue or green depending on production run — both are functionally identical. This valve is for HE top-load washers only. Always verify your model number before ordering. Key Features 4-solenoid valve assembly — controls hot water, cold water, and additional dispenser/recirculation ports to fill the tub with the correct temperature water for each cycle Integrated thermistor on center outlet — monitors incoming water temperature and communicates with the control board to achieve the correct wash temperature Resolves F8E1, LF, and LO FL error codes on compatible Maytag and Whirlpool HE top-load washers Rated 120V, 60Hz — correct electrical specifications for compatible models Dimensions: 5-3/8"L x 4-1/4"W x 3"H 2 inlet ports, 3 outlet ports — compatible with 1/2" ID supply hoses Valve body color (blue or green) varies by production run — functionally identical Replaces W10599423, W10758828, W10839828, W11096267, and W11165546VP Compatible with Maytag Bravos XL MVWB series, Whirlpool WTW7xxx/WTW8xxx, Kenmore 700 series, and Crosley top-load washers Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 15–25 minutes with basic hand tools Product Specifications Part Number W11165546 Part Type Washer Water Inlet Valve Assembly (4-Solenoid with Thermistor) Condition Aftermarket Replacement Application HE Top-Load Washers — Bravos XL, Cabrio, WTW series Solenoids 4-coil (hot, cold, and additional ports) Thermistor Integrated on center outlet — monitors water temperature Voltage 120V AC Frequency 60 Hz Dimensions 5-3/8"L x 4-1/4"W x 3"H Inlet Ports 2 (hot and cold) Outlet Ports 3 Supply Hose ID 1/2 inch Color White / Blue or Green (production run dependent — functionally identical) Error Codes Resolved F8E1, LF, LO FL Compatible Brands Maytag, Whirlpool, Kenmore, Crosley Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off both the hot and cold water supply valves before beginning. Pull the washer away from the wall to access the back panel. The water inlet valve is mounted on the upper rear of the washer. Photograph all wire harness connections and hose routing before disconnecting. Disconnect the two external supply hoses from the valve inlet ports using pliers to loosen any stuck connections. Disconnect the internal outlet hoses by squeezing the retaining clips and pulling free. Disconnect the wiring harness connectors from all solenoid coils and the thermistor. Unscrew the mounting hardware and remove the old valve. Install the new W11165546 valve in the same position, reconnect all internal hoses, wire harnesses, and external supply hoses in the same positions as documented. Restore water supply and power, then run a fill cycle to verify normal filling and check for leaks. Tools needed: Phillips screwdriver, pliers, channel-lock pliers for stubborn hose connections. Frequently Asked Questions What do error codes F8E1, LF, and LO FL mean on Maytag and Whirlpool washers? F8E1 (also displayed as LF or LO FL on some models) indicates a long fill fault — the washer was unable to fill to the required water level within the expected time. The most common causes are a failed water inlet valve (solenoid coil burned out or valve seat clogged), low household water pressure, or kinked supply hoses. Before replacing the valve, confirm both supply valves are fully open, the supply hoses are not kinked, and household water pressure is adequate. If all supply conditions are good and the error persists, the water inlet valve is the most likely cause. What is the difference between W11165546 and W11096267? These are the same water inlet valve assembly. W11096267 was an earlier version, and W11165546 is the current updated part number. The W10599423 and W10758828 are also cross-references to earlier versions of this same valve. The W11165546VP is the Whirlpool factory-packaged version. All of these are covered by this aftermarket replacement. Why does this valve have 4 solenoids? Modern HE top-load washers like the Maytag Bravos XL and Whirlpool Cabrio use multiple water paths for different wash functions — hot water inlet, cold water inlet, a bleach dispenser port, and a fabric softener/recirculation port. Each path is controlled by its own independent solenoid coil on the same valve assembly. This allows the control board to independently open any combination of ports needed for a given cycle phase. When any single solenoid coil fails, only the function controlled by that coil is affected — which is why the washer might fill normally with cold water but not hot, or fail to activate only one dispenser. Does the valve color (blue vs green) matter? No — the blue and green valve body colors are simply the result of different production runs at the factory. Both colors are the same part number (W11165546) with identical electrical specifications, port configuration, thermistor, and dimensions. Either color will function correctly in your washer. There is no functional difference between the two. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured with 4 solenoid coils and an integrated thermistor to match the electrical specifications and port configuration of the original W11165546 water inlet valve assembly. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less