Search results for "dishwasher seal"

3W40025L Genuine LG OEM Dishwasher Micro Switch – Compatible with LG Dishwashers Product Description Restore proper operation to your dishwasher with the 3W40025L Genuine LG OEM Dishwasher Micro Switch. This small but essential component detects door position or button activations, ensuring cycles start and stop correctly. A failed micro switch can cause the dishwasher not to run, stop mid-cycle, or display error codes. Replacing it with this genuine LG part restores dependable performance and safety. Replaces Part Numbers 3W40025L, D3V-16G-1C25, PD00035953, EAP5574491, AP5650845 PS5574491. Compatibility This micro switch is compatible with select LG dishwashers. Example compatible models include (but are not limited to): LG LDF7774ST, LDF8764ST, and LDF6810ST. Always verify your dishwasher’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 OEM Replacement – Genuine LG part for reliable performance 🔒 Cycle Safety – Ensures proper door detection and cycle control 💰 Cost-Effective OEM Part – Built to last with factory-tested quality 🛠️ Easy to Install – Small component, quick replacement with basic tools 🛡️ Fixes Common Issues – Resolves dishwashers not starting, stopping mid-cycle, or showing error codes 📐 Product Specification Part Number: 3W40025L Component Type: Dishwasher Micro Switch, 16A  125/250VAC Material: High-durability plastic housing with electrical contacts Mounting: Direct replacement switch with snap-in or screw mount Operating Conditions: Designed for standard dishwasher use Compliance: Genuine LG OEM certified 🛠️ Installation Notes Tools Needed: Phillips screwdriver, flathead screwdriver, needle-nose pliers ⚠️ Safety First: Always disconnect the dishwasher from power before starting repairs. Steps: Disconnect power supply to dishwasher. Access control panel or door latch assembly (depending on model). Locate and remove the faulty micro switch. Install the new 3W40025L switch and reconnect wiring. Reassemble the control panel or door latch assembly. Restore power and test dishwasher operation. ⏱️ Time Required: 15–20 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders 🛠️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Get your dishwasher running properly again — Add to Cart Now for a genuine, factory-approved fix!

Read more less

00622058 Dishwasher Genuine OEM Water Valve  Fits Specific Bosch Dishwasher Models Description: This dishwasher Water Inlet Valve is a Genuine OEM part for specific Bosch dishwasher models. This component is responsible for controlling the flow of water into the dishwasher. It operates via electrical signals from the dishwasher's control board, opening to allow water to enter during the fill cycle and closing to prevent water from entering during other cycles. ✅ Key Features: Genuine OEM Part for Bosch #00622058 120V, 60Hz single solenoid valve Includes mounting bracket and hose connection port Durable thermoplastic construction 🔁 Replaces Part Numbers: 00622058, 1999956, 622058, AH3491417, AP4927070, EA3491417, PS3491417, PS8728724. 🔧 Fixes These Common Symptoms: Dishwasher not filling with water Low or slow water flow Water inlet error codes Humming or clicking without water intake Leaking around the valve area 🧰 Compatible With: ✔️ Bosch✔️ Thermador✔️ Gaggenau✔️ Siemens(Check your model number or contact us for assistance.) ✅ Affordable aftermarket solution ✅ Always Fast and Free U.S. shipping ✅ Backed by helpful support and easy returns ✅ Trusted by DIYers and appliance techs 🛒 Restore your dishwasher’s performance — order the 00622058 water inlet valve today from Parts-O-Matic.com, and get it delivered fast and free.

Read more less

WD21X10224 Genuine GE / Hotpoint Dishwasher Interlock Switch Replaces Part Numbers:AP3872949, 1168295, AH1021382, EA1021382, PS1021382   California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

DC62-00223A Washer Center Tub Seal – Replacement for Samsung Washers Product Overview The Center Tub Seal is a replacement part compatible with Samsung washers. This seal is located on the center tub assembly and provides a watertight barrier between the inner and outer tubs. It prevents water from leaking out during the wash cycle. Fits Specific Samsung Washer Models. Replaces Part Numbers This seal replaces DC62-00223A, AP4211943, PS4208713. Designed to match the original dimensions and performance of the factory part. Compatible Brands Compatible with Samsung front-load washer models, Fits various models that require a shaft-to-tub seal of this type. Fixes the Following Issues Water leaking from under the washer Noisy spin cycle due to worn seal Mold or mildew forming near tub bearing Internal water damage from leaking shaft area Why Buy from Parts‑O‑Matic Reliable aftermarket quality Fast and free U.S. shipping Helps extend washer lifespan and prevent damage Trusted by repair professionals and homeowners

Read more less

WPW10481149 Dishwasher Touchpad and Control Panel Fits Specific KitchenAid Dishwasher Models Color: White   Replaces Part Numbers: WPW10481149, W10356933, W10481149, AP6022134, PS11755463.    California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

XPARTCO 4933DD3001B Dishwasher Door Hinge Cable – Compatible with LG & Kenmore Dishwashers Product Description Restore smooth and controlled dishwasher door movement with the XPARTCO 4933DD3001B Dishwasher Door Hinge Cable. This high-quality aftermarket replacement connects the dishwasher door to the hinge spring system, allowing the door to open and close evenly without slamming or dropping. A worn or broken hinge cable can cause the door to fall open, feel too heavy, or fail to stay balanced. Replacing it with this durable XPARTCO cable helps restore proper door tension and safe operation. XPARTCO is a trusted aftermarket brand offering appliance replacement parts designed to meet OEM-equivalent specifications at a cost-effective price. Replaces Part Numbers 4933DD3001B, 1395107, 4933DD3001A, PD00001803, EAP3524406, AH3524406, AP4511304, EA3524406, PS3524406   Compatibility This replacement dishwasher door hinge cable fits select LG and Kenmore (LG-manufactured) dishwashers. Example compatible models include (but are not limited to):LG LDF7811ST, LDF6920STKenmore 795.13293K701, 795.13299K701 Always verify your dishwasher’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM fit, length, and tension performance 🚪 Restores Proper Door Balance – Prevents door from dropping or slamming 💪 Durable Steel Cable – Designed to withstand repeated door cycles 💰 Cost-Effective Repair – Reliable alternative to OEM hinge cables 🛡️ Fixes Common Issues – Solves loose door, uneven opening, or excessive door weight 📐 Product Specification Part Number: 4933DD3001B Component Type: Dishwasher Door Hinge Cable Material: Braided steel cable with end fittings Application: Door hinge and spring tension system Installation Side: Typically used on left or right side (model dependent) Quality Level: Aftermarket replacement (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, needle-nose pliers ⚠️ Safety First: Disconnect power to the dishwasher before servicing. Door springs are under tension—use caution during installation. Basic Steps: Disconnect dishwasher power. Remove the lower access panel. Carefully release tension from the old hinge cable. Remove the damaged cable from the hinge and spring. Install the new XPARTCO 4933DD3001B cable in the same routing. Reattach spring tension and reinstall access panel. Test door movement for smooth, balanced operation. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Aftermarket Appliance Parts 🔄 30-Day Return Policy Restore smooth, controlled dishwasher door operation — Add to Cart Now for a dependable, budget-friendly repair!

Read more less

DC62-30314L Dishwasher Water Valve - Compatible with Samsung Dishwashers Product Description Ensure your dishwasher operates efficiently with the replacement DC62-30314L Dishwasher Water Valve. This high-quality replacement water inlet valve, designed for Samsung dishwashers, regulates water flow to ensure proper filling during wash cycles. Constructed from durable plastic and metal, this single-coil valve addresses issues like no water entering, continuous filling, leaks, or abnormal noises. Note: Includes one water inlet valve. Shut off water supply and unplug the dishwasher before installation. Replaces part numbers: DC62-30314L, 3992459, 33290415, PD00041597, EAP4208749, AP5582579, PS4209101, EAP4209101. Compatibility: Compatible with models including but not limited to: Samsung: DW80H9970US/AA, DW80J7550UG/AA, DW80K5050UB/AA, DW80K5050UG/AA, DW80K5050US/AA, DW80K5050UW/AA, DW80K7050UG/AA, DW80R9950QN/AA, DW80R9950UG/AA, DW80R9950US/AA, DW80R9950UT/AA, DW80R5060US/AA, DW80R5061US/AA, DW80J3020UW/AA, DW60M9990AP/AA Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Samsung dishwasher models. 🔥 Specifications: replacement water inlet valve, single-coil, plastic and metal construction, 110-120V, 60Hz, 0.75" inlet (GHT), 0.75" outlet (FPT), designed for reliable water flow regulation. 💰 Cost-Effective Alternative: replacement valve offers OEM-equivalent performance at a lower price. 🛠️ Easy Installation: Requires a screwdriver, pliers, work gloves; typically installed in 20–40 minutes. 🛡️ Reliable Fixes: Resolves no water, continuous filling, leaks, abnormal noises, or improper cleaning. Installation Notes: Safety First: Unplug the dishwasher and shut off the water supply before installation. Shop Parts-O-Matic for high-quality replacement appliance parts with a 30-day return policy. Keep your dishwasher running smoothly today! Add to cart now for a budget-friendly fix!

Read more less

XPARTCO WD21X10519 Dishwasher Flood Switch – Compatible with GE, Hotpoint, and RCA Dishwashers Product Description Prevent overfilling and protect your dishwasher from water damage with the XPARTCO WD21X10519 Dishwasher Flood Switch. This Flood Switch Assembly is a replacement part compatible with GE dishwashers. The dishwasher flood switch and thermistor assembly is responsible for detecting and preventing water from overflowing the dishwasher. It is located at the base of the tub and detects when water is present in the base from a leak, preventing the water inlet valve from filling further. The thermistor shuts off the water flow from the valve if the incoming water temperature is outside of the acceptable range. Replaces Part Numbers WD21X10519, 3028650, WD21X10492, WD21X20204, PD00023214, EAP8690623, AP5781465, PS8690623. Compatibility This replacement flood  switch fits select GE, Hotpoint, and RCA dishwashers. Example compatible models include (but are not limited to): GE GSD2100V65BB, GDF520PGJ2WW, Hotpoint HDA3600H35BB, and RCA RBD3300G00BB. Always verify your dishwasher’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Designed to meet OEM performance and safety standards 💧 Prevents Overfilling – Accurately detects water level and stops excessive filling 💰 Budget-Friendly Alternative – Provides OEM-like reliability at a lower cost 🛠️ Quick & Easy Installation – Simple wiring connection for fast repair 🛡️ Fixes Common Issues – Solves leaking, overfilling, or dishwasher not filling problems 📐 Product Specification Part Number: WD21X10519 Component Type: Dishwasher flood Switch Material: Plastic flood housing with integrated electrical microswitch Mounting: Direct-fit installation beneath dishwasher tub Function: Monitors water level and signals control board Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, pliers (optional) ⚠️ Safety First: Always unplug the dishwasher or turn off its circuit breaker before servicing. Steps: Disconnect power to the dishwasher. Remove the toe-kick panel to access the flood  switch area. Disconnect the wiring connector from the old switch. Twist or unclip the old flood switch and remove it. Install the new XPARTCO WD21X10519 switch in the same position. Reconnect wiring, reinstall toe-kick panel, and restore power. Run a quick fill test to confirm proper operation. ⏱️ Time Required: 10–15 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Protect your dishwasher from overfilling — Add to Cart Now for a reliable, cost-effective repair!

Read more less

154825001 Genuine OEM Frigidaire Dishwasher Heating Element The 154825001 is a genuine Frigidaire OEM round heating element that sits exposed at the bottom of the dishwasher tub. Unlike a hidden element concealed beneath the tub floor, this is a visible ring-shaped element you can see sitting right in the bottom of the wash chamber. It serves two jobs: it heats the wash water to the temperature needed to properly dissolve detergent and break down grease and food soil, and at the end of the cycle it provides the heat that drives the drying phase, helping moisture evaporate off your dishes rather than leaving them wet. Mounted through a 0.98" hole with two mounting nuts and connected by two wire terminals, this element carries a pair of white alignment dots that must line up with the tub's retaining clips during installation. Over time, mineral buildup from hard water, general corrosion, or simple electrical wear can cause the element to fail. A failing or dead element produces a specific and recognizable pattern: water never gets hot enough to clean effectively, dishes come out wet at the end of the cycle instead of dry, and the whole cycle may run noticeably longer as the dishwasher's control tries to compensate. It directly replaces AP5628696, 154482901, 154663801, 2308825, PS3653449, and EAP3653449. As a genuine OEM part, the 154825001 is manufactured by Frigidaire to factory specifications — guaranteed fit, materials, and performance. Quick Answer The 154825001 Genuine OEM Frigidaire Dishwasher Heating Element fixes Frigidaire, Kenmore, Electrolux, Crosley, Gibson, Kelvinator, Tappan, and Westinghouse dishwashers with dishes that don't get properly clean, dishes that come out wet instead of dry, or cycles that take longer than they used to. Exposed round heating element, 0.98" mounting hole, 2 wire terminals. Replaces AP5628696, 154482901, 154663801, 2308825, PS3653449, EAP3653449. Before replacing, test the old element with a multimeter for resistance — a bad control board relay can produce identical symptoms with a perfectly good element. Common Problems This Part Fixes Dishes not getting properly clean because wash water isn't reaching the correct temperature Dishwasher not drying dishes — items come out wet at the end of the cycle Cycle taking noticeably longer than usual to complete Visible damage, corrosion, or discoloration on the element itself Element that doesn't glow or heat up when the wash cycle is running Water leaking near the high-temperature wire connector at the element terminals Mineral scale buildup visible on or around the element Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dishwasher heating element directly replaces the following OEM and cross-reference part numbers: 154825001, 154482901, 154663801, 2308825, AP5628696, AFR14520, EAP3653449, PD00000951, PS3653449. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This heating element is compatible with select Frigidaire, Electrolux, Kenmore, Crosley, Gibson, Kelvinator, Tappan, and Westinghouse dishwashers, spanning a wide range of model series including BBBD, BGBD, BGHD, DGBD, DGCD, DGHD, FDB, FDBB, FDBD, FFBD, FFID, FGBD, FGCD, FGHD, FGID, FPHD, FPID, GLD, GSB, LEDB, LFBD, LFID, LGBD, LGHD, and PLD. Verified model numbers include: FFCD2413UW1A, FGID2466QF4A, FGID2466QF5A, FFID2426TD1A, FGBD2438PF4A, FGHD2465NF1A, FGHD2433KF1, LFID2426TF1A, LFID2422RF0A, LFID2422RF3B, LFID2422RF4B, LFID2426TF4A, LFID2426TF5A, LGBD2431LF0A, LGBD2431NF0B, LGBD2431NF1B, LGBD2432LW0A, LGBD2432LW0B, and CDB350/CDB500/CDB900 series models. Also fits Kenmore 587-series, Crosley CBD-series, Kelvinator KADB240, and White-Westinghouse WWBD2400 dishwashers. Note: This is an exposed round heating element sitting visibly in the bottom of the tub, not a hidden element mounted underneath. It is not interchangeable with hidden/concealed heating elements used on other dishwasher platforms. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine Frigidaire OEM part — factory-specified heating output and terminal configuration Exposed round design sits in the tub bottom for direct water heating and drying support Resolves "not cleaning properly," "not drying," and "cycle taking too long" symptoms caused by element failure 0.98" mounting hole with two mounting nuts and wire terminals Two white alignment dots for correct positioning in the tub's retaining clips Direct drop-in replacement — no modification required Replaces 154482901, 154663801, 2308825, AP5628696, PS3653449, and EAP3653449 Compatible with Frigidaire, Electrolux, Kenmore, Crosley, Gibson, Kelvinator, Tappan, and Westinghouse dishwashers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number 154825001 Part Type Dishwasher Round Heating Element (Exposed) Condition Genuine OEM Brand Frigidaire / Electrolux Location Bottom of the wash tub (exposed, visible) Mounting Hole 0.98 in. Terminals 2 wire connections + 2 mounting nuts Alignment 2 white dots must align with tub retaining clips Repair Difficulty Medium — basic dishwasher familiarity required Tools Required Screwdrivers, wrench set Quantity 1 heating element Compatible Brands Frigidaire, Electrolux, Kenmore, Crosley, Gibson, Kelvinator, Tappan, Westinghouse Installation Notes ⚠️ Unplug Dishwasher And Shut Off Water Before Starting — Handle The Element Carefully Disconnect power at the circuit breaker and shut off the water supply before beginning. Wear work gloves. On many models you'll need to pull the dishwasher out from under the counter to access the undercarriage — remove the two screws securing the unit to the counter first. Remove the lower rack and the lower spray arm (it typically pushes down and twists to unlock) to access the element inside the tub. From underneath, disconnect the two wires from the element's terminals and remove the two mounting nuts with a 1/2" wrench, taking care not to overtighten when you reach the new element — over-torquing can crush the sealing washers and cause a leak at the connector. Lift the old element free from its retaining clips inside the tub. To install the new 154825001, locate the two white alignment dots on the element and position them so they slide into the tub's retaining clips correctly — this ensures the element seats in its proper orientation. Push the terminals down through the mounting hole, then from underneath, reinstall and tighten the mounting nuts snugly but not excessively. Reconnect the two wires to the terminals, reinstall the lower spray arm and press it down to lock it in place, and reinstall the lower rack. Restore water and power, then slide the dishwasher back into place and secure it to the counter with its mounting screws. Run a test cycle and check underneath for any leaks at the element connection before considering the repair complete. Tools needed: screwdriver, 1/2" wrench, work gloves. Frequently Asked Questions How do I know it's the heating element and not something else, like the control board? Before replacing the element, it's worth testing it with a multimeter for resistance — a healthy element typically reads in the neighborhood of 14 ohms, though exact values vary by model. If the old element tests fine but dishes still aren't drying or getting hot enough, the more likely cause is upstream of the element itself, such as a control board relay that isn't sending power to it correctly. Some owners have replaced a perfectly good element only to find the actual fault was a bad solder connection on the control board relay — testing first can save you an unnecessary purchase. Can I clean the element instead of replacing it? Light surface cleaning to remove mineral scale buildup is reasonable and can sometimes help if reduced heating output is due to scale insulating the element. However, if the element tests as an open circuit (no continuity) or shows visible damage, cracking, or corrosion through the metal sheath, cleaning won't restore it — replacement is the correct fix at that point. I noticed water leaking near the element's wire connector. Is that related? Yes, this is a documented failure point on this element design — the high-temperature wire connector at the terminals can develop a leak, especially if the mounting nuts were overtightened during a prior installation and damaged the sealing washer. When installing the new element, tighten the mounting nuts snugly but avoid excessive force, which helps prevent this same leak point from recurring. Do I really need to pull the dishwasher out from under the counter? On most installations, yes — accessing the mounting nuts and wire terminals underneath the tub requires pulling the unit forward after removing the two screws that secure it to the counter. Some technicians have managed the nut removal with a deep socket without fully pulling the unit, but planning for full access makes the job considerably easier, especially the first time. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Frigidaire to factory specifications — guaranteed fit, materials, and performance. It matches the original heating output, mounting configuration, and terminal layout of the element originally installed in your dishwasher. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WPW10455261 Dishwasher Genuine OEM Pump and Motor Assembly Fits specific Whirlpool, Maytag, Kenmore Dishwasher models Description: This Dishwasher Pump & Motor is an OEM replacement part for specific Whirlpool dishwasher models. As the main component for water circulation, it contains both the water pump and motor required to power it. Replaces Part Numbers: WPW10455261, W10455261, 2312159, W10500284, AP6021679, PS11755005. California Residents only WARNING: California’s Proposition 65 

Read more less

PK136277-2 Lower Dishrack Roller and Axle Set Pack of 2 Replaces: WD12X10136,  WD12X10277   This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

AEC74337401 Dishwasher Water Inlet Guide - Compatible with LG Dishwashers Product Description Restore your dishwasher’s cleaning performance with the AEC74337401 Water Inlet Guide from Parts-O-Matic. This genuine OEM replacement guide directs water from the inlet valve into the dishwasher tub, ensuring proper water flow for wash and rinse cycles. Designed for LG dishwashers, it fixes issues like insufficient water, poor cleaning, or water inlet error codes.  Note: Includes one water inlet guide. Take photos of connections during disassembly and clean the inlet valve before installation. Replaces part numbers: AEC74337401, AP6233501, PD00056036, PS12078211. Compatibility: Compatible with models including but not limited to: Verify your model number or contact Parts-O-Matic support for assistance. Key Features: ✅ Brand Compatibility: Fits select LG dishwasher models. 💧 Specifications: OEM plastic water inlet guide, designed for secure water flow and durability. 💰 Cost-Effective: OEM performance at a competitive price. 🛠️ Easy Installation: Requires a screwdriver, pliers, work gloves; typically installed in 20–30 minutes. 🛡️ Reliable Fixes: Resolves insufficient water, poor cleaning, or water inlet error codes. Installation Notes: Safety First: Unplug the dishwasher and turn off the water supply before installation to avoid shock or leaks. Clean the inlet valve and hose to prevent clogs. Access the inlet guide (inside or near the bottom of the dishwasher), disconnect the old guide, and install the new one, ensuring tight connections. Shop Parts-O-Matic for high-quality replacement appliance parts with a 30-day return policy. Keep your dishwasher running smoothly today! Add to cart now for a budget-friendly fix!

Read more less