Search results for "washer sensor"

W11210459 Genuine OEM Whirlpool Washer Water Inlet Valve The W11210459 is a genuine Whirlpool OEM water inlet valve for Whirlpool top-load washers, and also fits select Kenmore, Maytag, Amana, Crosley, Inglis, and Roper models. This valve controls the flow of hot and cold water into the tub during the fill portion of each cycle — an electrical solenoid opens and closes the valve to admit exactly the right amount of water for the selected wash setting. Over time, mineral or sediment buildup inside the valve, or general wear in the solenoid coil, can cause the valve to fail. A failing valve typically shows up as the washer not filling with water, filling very slowly, or water continuing to leak into the tub after the wash has completed. It directly replaces AP6329217, W10701459, W10838319, W11038711, 4591321, PS12349267, W10869799, W11025984, and W11210459VP. Quick Answer The W11210459 Genuine OEM Whirlpool Washer Water Inlet Valve fixes Whirlpool, Kenmore, Maytag, Amana, Crosley, Inglis, and Roper top-load washers that won't fill, fill very slowly, or continue leaking water into the tub after the wash has finished. Replaces AP6329217, W10701459, W10838319, W11038711, 4591321, PS12349267, W10869799, W11025984, W11210459VP. The control panel can be removed more easily with a putty knife slid under each end to release the clips, rather than removing the back panel first. Common Problems This Part Fixes Washer not filling with water Washer filling very slowly Water continuing to leak into the tub after the wash cycle has completed No hot water reaching the tub, or no cold water reaching the tub Cycle stalling at the fill step and never advancing to wash Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer water inlet valve directly replaces the following OEM and cross-reference part numbers: W11210459, W10701459, W10838319, W11038711, 4591321, W10869799, W11025984, 33190189, 33190190, W10423122, W10423124, W10868380, W10868381, AP6329217, AWP43369, EAP12349267, OEM18987660, PD00042885, PS12349267 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water inlet valve is compatible with select Whirlpool top-load washers, and also fits select Kenmore, Maytag, Amana, Crosley, Inglis, and Roper washers built on the Whirlpool platform, including model numbers such as WTW5000DW1 and WTW4816FW2. Note — not the same as W11210463: A similarly-numbered valve, W11210463 (also cross-referenced as W11101906), is a separate part with its own cross-reference set (W10701461, W10883458, W10869803, W11038696, AP6329219), used on other Whirlpool washer models. The two are easy to confuse given how close the numbers are — always confirm you have the exact part number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine Whirlpool OEM part — factory-specified solenoid design and flow rate Regulates hot and cold water flow into the washer tub Resolves "won't fill," "fills slowly," and "leaks after cycle completes" symptoms caused by valve failure Factory Certified Part built to Whirlpool's engineering specifications Direct drop-in replacement — matches the original mounting and hose connections Replaces AP6329217, W10701459, W10838319, W11038711, 4591321, PS12349267, W10869799, W11025984, and W11210459VP Compatible with Whirlpool, Kenmore, Maytag, Amana, Crosley, Inglis, and Roper top-load washers Genuine OEM replacement — guaranteed fit, materials, and performance Moderate DIY repair Product Specifications Part Number W11210459 Part Type Washer Water Inlet Valve Condition Genuine OEM Brand Whirlpool Application Top-Load Washers Function Controls hot and cold water flow into the tub Repair Difficulty Moderate Quantity 1 valve Compatible Brands Whirlpool, Kenmore, Maytag, Amana, Crosley, Inglis, Roper Installation Notes ⚠️ Unplug Washer And Shut Off Water Supply Before Starting — Use A Putty Knife To Release The Control Panel Disconnect power at the outlet, or shut off the house circuit breaker for the appliance, and shut off both hot and cold water supplies before beginning. Wear work gloves. The top control panel can be removed more easily by sliding a putty knife under the panel on each end to release the retaining clips, rather than removing the back panel first — one customer specifically noted this trick saved considerable time after trying the back-panel approach without success. With the panel released, locate the water inlet valve and photograph the wiring and hose connections before disconnecting anything. Disconnect the electrical connector and the hot/cold water lines from the old valve, remove its mounting screws, and pull it free. Install the new W11210459 in the same position, reconnect the water lines and electrical connector fully, and secure the mounting screws. Reinstall the control panel. Restore the water supply and power, then run a full test cycle across a few temperature settings to confirm correct fill behavior with no leaking. Tools needed: multi-screwdriver, putty knife, work gloves. Frequently Asked Questions My washer isn't filling with water. Is this the right part? Yes, this is the most direct symptom of a failed water inlet valve. Since this valve is what admits water from your household supply into the washer, a solenoid failure or internal blockage can prevent any water from entering at all, stopping the wash cycle from proceeding. What's the easiest way to access the control panel for this repair? Try sliding a putty knife under the panel at each end to release the retaining clips, rather than removing the back panel of the washer first. One customer specifically learned this trick after trying the back-panel approach with no luck, then found the putty knife method worked cleanly after watching an online tutorial. Is this the same as W11210463? No, these are two separate Whirlpool valve part numbers with different cross-reference sets, despite the similar numbering. Always confirm the exact part number from your washer's parts diagram or the sticker on your old valve rather than assuming based on a close number match. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original solenoid design, flow rate, and connection type of the water inlet valve originally installed in your washer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

131436700 Washer Genuine Control Timer   Replaces Part Numbers:  131436700, OEM8427502, AP2106875, 407393, AH417799, EA417799, PS417799.  

Read more less

XPARTCO WH12X955 Washer Lid Switch The XPARTCO WH12X955 is an aftermarket replacement lid switch assembly compatible with GE, Hotpoint, RCA, and Kenmore GE-built washer/dryer combo units (including GE spacemaker and stacked laundry models). The lid switch is a safety component mounted inside the washer lid — it detects whether the lid is open or closed and signals the control that it's safe for the machine to start, agitate, and spin. When the lid closes, the switch activates and the washer can run through its full cycle. If the lid switch fails, the washer typically won't spin or drain, may not start or agitate at all, and clothes are left sitting in water. This is a complete lid switch assembly with an integrated wiring harness and ground wire. Dimensions: 1-1/4" H x 2-1/4" W x 16" D (the 16" depth is the wire harness that routes from the lid down into the washer cabinet). It directly replaces WH12X955, WH12X0955, AP2045786, 278666, AH270219, EA270219, PS270219, and OEM6137363. Installation involves accessing the lid itself — the switch mounts inside the lid with two screws plus a separate ground wire screw. Installs in 30–45 minutes with basic hand tools. Quick Answer The XPARTCO WH12X955 Washer Lid Switch fixes GE, Hotpoint, RCA, and Kenmore GE-built washer/dryer combo units where the washer won't spin, won't drain, won't start, or won't agitate — leaving clothes sitting in water. Complete lid switch assembly with wiring harness and ground wire. Dimensions 1-1/4"H x 2-1/4"W x 16"D. Replaces WH12X0955, AP2045786, 278666, AH270219, EA270219, PS270219, OEM6137363. Classic symptom: washer won't spin or drain. Common Problems This Part Fixes Washer won't spin — the classic lid switch failure symptom Washer won't drain — clothes left sitting in water at the end of the cycle Washer won't start at all — control not detecting a closed lid Washer won't agitate — the machine won't advance past the fill phase Machine doesn't recognize the lid is closed even when it is Lid switch body cracked from the lid being closed hard over time Internal switch contacts worn out — no longer signaling that the lid is closed Intermittent operation — washer sometimes spins, sometimes doesn't, depending on lid position Broken or frayed lid switch wiring harness Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer lid switch directly replaces the following OEM and cross-reference part numbers: WH12X955, 278666, AGE25981, AH270219, EA270219, PD00030733, EAP270219, PS270219, AP2045786, WH12X0955, EXPWH12X955 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This lid switch assembly is compatible with select washer/dryer combo units (spacemaker and stacked laundry models) from the following brands: GE washer/dryer combo units — spacemaker and stacked laundry center models GE Spacemaker washers — select models Hotpoint washer/dryer combo units (select GE-built models) RCA washer/dryer combo units (select GE-built models) Kenmore / Sears washer/dryer combo units (select GE-built models) Note: This lid switch is specific to GE washer/dryer combo and spacemaker units — it is NOT the same switch used on standalone GE top-load washers, which use different lid switch part numbers. Always search by your appliance model number to confirm this part fits before ordering. Contact our support team with your model number if you're unsure. Key Features Lid switch safety assembly — detects whether the lid is open or closed and allows the washer to start, agitate, spin, and drain when the lid is shut Resolves the classic "won't spin" and "won't drain" symptoms of lid switch failure Complete assembly with integrated wiring harness and ground wire Dimensions: 1-1/4" H x 2-1/4" W x 16" D (the 16" depth is the wiring harness) Mounts inside the washer lid with two screws plus a separate ground wire screw Snap-in switch design with connector — no wiring modifications required Replaces WH12X0955, AP2045786, 278666, AH270219, EA270219, PS270219, and OEM6137363 Compatible with GE, Hotpoint, RCA, and Kenmore GE-built washer/dryer combo and spacemaker units Aftermarket replacement built to OEM-equivalent quality standards DIY-friendly repair — installs in 30–45 minutes with basic hand tools Product Specifications Part Number WH12X955 Part Type Washer Lid Switch Assembly Condition Aftermarket Replacement Application Washer/Dryer Combo & Spacemaker Units (GE platform) Dimensions 1-1/4" H x 2-1/4" W x 16" D Includes Lid switch, wiring harness, ground wire Function Prevents washer spin/agitation when lid is open Location Inside the washer lid Mounting Two screws + separate ground wire screw Compatible Brands GE, Hotpoint, RCA, Kenmore (GE-built) Installation Notes ⚠️ Unplug Washer Before Starting — Wear Work Gloves — The Lid Comes Off Disconnect power at the outlet or breaker before beginning. Wear work gloves to protect your hands from sharp sheet metal edges. This repair requires removing the washer lid to access the switch. Open the lid, then push it toward the back of the machine to release the plastic clips at the front that hold the lid up. Slowly lift the lid at the front — you'll see the lid switch is the only thing still connecting the lid to the washer body. Confirm the power is off, then unclip the electrical connector that joins the lid switch harness to the washer's wiring (it's typically a molex-style connector). With the connector released, you can carry the lid to a workbench or flat surface to work on it comfortably. On the underside/inside of the lid, remove the two screws on the right-hand side that hold the switch in place, then remove the screw that secures the ground wire to the inside of the lid. Lift out the old switch. The new WH12X955 switch snaps into place — seat it, reinstall the two mounting screws, and reattach the ground wire with its screw. Route the new harness cable through the same path as the old one; you can gently lift the retaining clips with a flathead screwdriver to slide the new cable through. Reconnect the electrical connector, set the lid back into position, and press it down until the front plastic clips engage. Restore power and test by closing the lid and running a cycle — confirm the washer agitates, drains, and spins. Tools needed: Phillips screwdriver, nut driver, flathead screwdriver, work gloves. (Tip: if you drop the ground wire nut inside the cabinet, a magnet on a stick makes retrieval easy.) Frequently Asked Questions My washer won't spin or drain — is the lid switch the cause? Yes — this is the single most common and telling symptom of a failed lid switch. The lid switch is a safety interlock that prevents the drum from spinning while the lid is open. When the switch fails (cracked body, worn internal contacts, or broken wiring), the control never receives the "lid closed" signal, so it blocks the spin and drain phases as a safety measure — leaving your clothes sitting in water. On many GE washer/dryer combos, a failed lid switch will also prevent the machine from starting or agitating at all. If your washer fills but goes no further, or completes the wash but leaves clothes soaked, the lid switch is the prime suspect. You can confirm by testing the switch for continuity with a multimeter when the lever is depressed. Why is this switch 16" long? The 16" dimension is the length of the wiring harness, not the switch body itself. The switch mounts inside the washer lid, and its harness has to route from the lid, through the hinge area, down into the washer cabinet to reach the main wiring connector. That's why the assembly comes with a long attached cable — and it's also why this repair involves removing the lid to access everything. The switch body itself is compact at roughly 1-1/4" H x 2-1/4" W. Does this fit my standalone GE top-load washer? Probably not. The WH12X955 is specifically used on GE washer/dryer combo units and spacemaker/stacked laundry models. Standalone GE top-load washers use different lid switch part numbers. Because the lid switch design and mounting vary significantly across GE's washer lineup, always search by your appliance model number to confirm the correct part before ordering. If your unit is a standalone top-loader, contact our support team with your model number and we'll identify the right lid switch for it. Do I really have to take the lid off to install this? On most compatible models, yes — the lid switch mounts inside the lid itself, so you'll need to release the lid from the washer body to reach the two mounting screws and the ground wire screw. The good news is that the lid comes off fairly easily: push it toward the back to release the front plastic clips, then lift it slowly, unclip the electrical connector, and carry the lid to a comfortable work surface. Working on the lid off the machine is far easier than trying to reach into a cramped laundry closet. Just be sure power is disconnected before unclipping the connector. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured to match the dimensions (1-1/4"H x 2-1/4"W x 16"D), harness and ground wire configuration, connector, mounting, and lid-detection function of the original WH12X955 lid switch used in compatible GE, Hotpoint, RCA, and Kenmore GE-built washer/dryer combo and spacemaker units. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 4681EA2001T Washer Drain Pump Motor The XPARTCO 4681EA2001T is an aftermarket replacement drain pump motor assembly compatible with a wide range of LG and Kenmore front-load washers. The drain pump motor forces water out of the washer drum through the drain hose during and after the wash and spin cycles — when it fails, the washer will not drain, will display an OE error code, leave standing water in the drum, or produce a loud humming or grinding noise during the drain phase. This drain pump motor is rated at 120V–127V, 60Hz, 85W, 1.4A with a flow rate of 45 liters per minute and a spin speed of 1,100–1,200 RPM. It is made from durable metal and ABS plastic and includes the pump impeller and a removable filter housing with sealing ring for quieter, smoother operation. Note: this is the motor assembly only — it reuses the existing pump housing from your washer. It directly replaces 4681EA2001N, 4681EA1007G, 4681EA1007D, AP5328388, and several additional cross-reference numbers. Installs in 30–60 minutes with basic hand tools. Quick Answer The XPARTCO 4681EA2001T Washer Drain Pump Motor fixes LG and Kenmore front-load washers showing OE error codes, not draining, leaving standing water, or making loud humming or grinding sounds during the drain cycle. Rated 120V–127V/60Hz/85W/1.4A, 45L/min, 1,100–1,200 RPM. Includes impeller and removable filter housing. Motor assembly only — reuses existing pump housing. Replaces 4681EA2001N, AP5328388, 4681EA1007G, and more. Common Problems This Part Fixes OE error code displayed — washer cannot drain within the allotted time Washer not draining — standing water remaining in the drum after a cycle Loud humming or buzzing during the drain cycle — motor running but impeller not turning Grinding or rattling noise during draining — physical damage to pump components Washer stopping mid-cycle due to a drain fault Washer draining very slowly — worn pump motor below rated flow Water leaking from the drain pump area Replaces Part Numbers This drain pump motor directly replaces the following OEM and cross-reference part numbers: 4681EA2001T, 4681EA1007G, 2003273, 4681EA1007D, 4681EA2001D, 4681EA2001N, 4681EA2001U, DP040-038, ALG51292, AH3579318, EA3579318, PD00001722, EAP3579318, AP5328388, PS3579318. 4681EA2001T is the current updated part number — it is the manufacturer-approved replacement for the older 4681EA2001N. If your washer or parts diagram shows 4681EA2001N, order 4681EA2001T. Compatibility This drain pump motor is compatible with select front-load washers from the following brands: LG front-load washers — WM2xxx, WM3xxx, WM4xxx, WM5xxx, WM8xxx, WM9xxx series Kenmore / Sears front-load washers (select LG-built models, including 796-series) Important: This is the pump motor assembly only — it installs into your washer's existing pump housing. The pump housing is not included and is reused from your old assembly. Always verify your model number before ordering. Contact our support team if you're unsure. Key Features Forces water out of the drum through the drain hose during wash and spin cycles at 45 liters per minute Rated 120V–127V, 60Hz, 85W, 1.4A — correct electrical specifications for compatible LG and Kenmore models Spin speed: 1,100–1,200 RPM for powerful, efficient drainage Includes pump impeller and removable filter housing with sealing ring Removable filter housing allows easy cleaning without full pump disassembly Sealing ring reduces vibration and noise during operation Durable metal and ABS plastic construction — built to withstand repeated high-volume drainage cycles Motor assembly only — installs into existing pump housing, no housing replacement needed Resolves OE error code on compatible LG and Kenmore front-load washers Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 30–60 minutes with basic hand tools Product Specifications Part Number 4681EA2001T Also Replaces 4681EA2001N (updated current replacement) Part Type Washer Drain Pump Motor Assembly Condition Aftermarket Replacement Application LG and Kenmore Front-Load Washers Voltage 120V – 127V AC Frequency 60 Hz Wattage 85W Amperage 1.4A Flow Rate 45 liters per minute Spin Speed 1,100 – 1,200 RPM Material Metal / ABS Plastic Includes Motor assembly, impeller, removable filter housing, sealing ring Note Motor assembly only — existing pump housing is reused Compatible Brands LG, Kenmore Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off the water supply before beginning any repair. Place towels and a shallow pan at the front of the washer to catch residual water. Open the small access panel at the lower front of the washer and drain any remaining water through the drain hose or filter port. Remove the front panel of the washer by unscrewing the top panel screws, then removing the door gasket retaining wire and door latch screws to free the front panel. With the front panel removed, the drain pump assembly is now visible at the lower front. Use a flat-head screwdriver to release the pump mounting clip, then disconnect the drain hoses using pliers to loosen the clamps. Disconnect the wire harness from the pump motor. Pull the motor assembly out of the pump housing. Install the new 4681EA2001T motor into the existing housing, reconnect the hoses and wire harness, secure the pump clip, and reassemble the front panel. Restore power and water supply, then run a drain/spin cycle to verify proper drainage. Tools needed: Phillips screwdriver, flat-head screwdriver, needle-nose pliers, slip-joint pliers, shallow pan. Frequently Asked Questions What is the difference between 4681EA2001T and 4681EA2001N? These are the same drain pump motor — 4681EA2001T is the updated current part number that replaced the older 4681EA2001N. LG issued the updated number during a production cycle revision. If your washer or its documentation shows 4681EA2001N, 4681EA2001D, or any other older variant, the 4681EA2001T is the correct replacement to order. What does the OE error code mean on an LG washer? OE (or OE error) stands for "Outlet Error" — it means the washer was unable to drain within the expected time. Common causes include a clogged drain filter, a blocked or kinked drain hose, or a failed drain pump motor. Before replacing the motor, check and clean the drain filter and inspect the drain hose for kinks or blockages. If both are clear and the washer still shows OE, the pump motor has likely failed and needs replacement. Does this include the pump housing? No — the 4681EA2001T is the motor assembly only. It installs into your washer's existing pump housing, which is not included and does not need to be replaced in most cases. If your pump housing is cracked or damaged, you will need to source it separately. In most repairs, the housing is reused and only the motor assembly is replaced. Should I check the drain filter before replacing the pump motor? Yes — always check and clean the drain filter first. LG front-load washers have a coin trap and filter at the lower front that should be cleaned regularly. A heavily clogged filter or a foreign object jammed in the impeller can cause OE errors and loud humming without the pump motor being permanently damaged. Remove the filter, clear debris from the impeller area, and test the washer. If the problem persists after cleaning, the motor is the likely culprit. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine LG OEM part, but is manufactured from durable metal and ABS plastic to match the electrical specifications and performance of the original 4681EA2001T drain pump motor assembly. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 280187 Washer Drain Pump Assembly The XPARTCO 280187 is an aftermarket replacement drain pump assembly for Whirlpool-built front-load washers sold under the Whirlpool, Kenmore, Kenmore Elite, Maytag, KitchenAid, and Amana names. The drain pump pushes water out of the tub through the drain hose at the end of the wash and rinse stages. When it clogs, wears out, or seizes, the washer can stop with water still in the drum, throw drain errors, stop before the spin cycle, leak, or make loud humming or grinding noises. This is a complete drain pump assembly, including the pump motor and housing, so it replaces the whole unit rather than just an internal part. The pump sits at the base of the washer behind the lower front panel, and the swap typically takes 15–30 minutes with common hand tools. Quick Answer The XPARTCO 280187 Drain Pump Assembly fixes a Whirlpool-built front-load washer that won't drain, leaves water in the drum, stops before spinning, leaks from the pump, or makes loud noise during draining. Complete pump motor and housing, aftermarket replacement. Classic symptom: the cycle stalls with water still in the tub, or you hear a loud hum or grind while it tries to drain. Common Problems This Part Fixes Washer won't drain, or water is left in the drum after the cycle Drain error codes or the cycle stopping before the spin Loud humming, grinding, or rattling while the washer drains Water leaking from the pump or its housing Pump motor seized or not running Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This drain pump assembly replaces the following part numbers: 280187, 1200164, 285998, 8181684, 8182819, 8182821, AH1485610, AP3953640, AWP39453, EA1485610, EAP1485610, PD00002352, PS1485610 These are Whirlpool's current and earlier numbers for this pump. If your old pump or parts diagram shows any of them, this is the matching replacement. Compatibility This pump is listed for select front-load washers from: Whirlpool, including Duet models such as WFW9400VE03, WFW9500TW03, and WFW9600TW02 Kenmore and Kenmore Elite, including 11042822200, 11042926200, 11045962400, and 11045966403 Maytag, including MHWE400WR00 and MHWE400WW0 KitchenAid, including KHWS02RWH0 Amana Note: The model list above is only a sample, since this pump fits many more models. Confirm fit by matching the number on your old pump or parts diagram against the Replaces list, or contact our support team with your model number and we'll verify before you order. This pump is for front-load washers and is not intended for top-load machines. Key Features Aftermarket replacement drain pump assembly Complete unit with pump motor and housing Restores full draining so cycles finish and the washer can spin Cross-references to Whirlpool 280187, 285998, 8181684, 8182819, and 8182821 Fits select Whirlpool, Kenmore, Maytag, KitchenAid, and Amana front-load washers Typical installation 15–30 minutes with common hand tools Product Specifications Part Number XP280187 OEM Part Number 280187 Part Type Washer Drain Pump Assembly Condition Aftermarket Replacement Included Pump Motor and Housing Application Select Whirlpool, Kenmore, Kenmore Elite, Maytag, KitchenAid & Amana Front-Load Washers Installation Notes ⚠️ Unplug Power and Expect Water Unplug the washer and turn off the water supply before starting. Remove the lower front panel to reach the pump at the base of the washer, then drain any residual water into a shallow pan or with a wet/dry vacuum, using the drain hose or the small drain cap if your model has one. Disconnect the wiring harness from the pump, then loosen the clamps holding the hoses and pull the hoses off. Remove the pump's mounting screw and take out the old pump. Fit the new pump in the same position, reattach the hoses with the clamps (replace worn clamps if needed), and reconnect the wiring harness. Check that the pump and hose connections are secure, replace the front panel, restore power and water, and run a drain cycle while checking for leaks. Common tools include a nutdriver or Torx driver, screwdrivers, and pliers. Frequently Asked Questions My washer won't drain. Is this the part I need? A failed or clogged drain pump is one of the most common causes. Before replacing it, check the drain hose and the pump filter for a clog, such as a sock or coin. If the filter is clear but the pump hums, grinds, or doesn't run, replacing the pump should fix it. Does this include the pump motor? Yes. This is the complete assembly, with the pump motor and housing. My old pump is marked 285998, 8181684, 8182819, or 8182821. Will this work? Yes. All of those are earlier Whirlpool numbers for this pump, and 280187 is the current number. Will this fit my top-load washer? It is intended for front-load washers. Contact our support team with your model number if you're unsure, and we'll confirm before you order. Is this an OEM part? No. This is an XPARTCO aftermarket replacement built to match the Whirlpool 280187. If you prefer a genuine OEM pump, contact us. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

W11700916 Washer Genuine OEM Door Latch The W11700916 is a genuine Whirlpool OEM lid lock assembly for Whirlpool top-load washers, and also fits select Maytag and Kenmore models. This assembly ensures the washer's lid remains securely locked during the wash and spin cycle, preventing access to the moving parts inside while the drum is in motion and confirming to the control board that the lid is safely closed before the cycle can proceed. This part is a superseding design, replacing the earlier W11394572 lid latch. Over time, the internal locking mechanism can wear out or fail electrically. A failing lid lock typically shows up as the lid not locking properly during a cycle, or the washer failing to start at all, since the control board won't proceed without confirmation the lid is securely closed. It directly replaces W11543566, W11394572, W11032875, AP7219279, and PS17217010. Quick Answer The W11700916 Washer Genuine OEM Door Latch fixes Whirlpool, Maytag, and Kenmore top-load washers where the lid isn't locking properly, or the washer won't start at all. Replaces W11543566, W11394572, W11032875, AP7219279, PS17217010. This is a newer superseding lid lock design — if your washer's original latch is one of the numbers it replaces, this is the correct current part to order. Common Problems This Part Fixes Lid isn't locking properly during the wash or spin cycle Washer won't start at all Lid pops open or unlocks unexpectedly mid-cycle Cycle stalls at the start and won't proceed to wash or spin Washer pumps or agitates but won't spin because the lid isn't sensed as locked Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer door latch directly replaces the following OEM and cross-reference part numbers: W11700916, W11394572, W11032875, W11543566, EG-380900, AP7219279, AWP46729, EAP17217010, OEM21657846, PD00085319, PS17217010 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This lid lock assembly is compatible with select Whirlpool top-load washers, and also fits select Maytag and Kenmore washers built on the Whirlpool platform, including model numbers such as: MVW8230HC0, MVW7230HW0, MVW7230HC0, MVW7232HC0, MVW7232HW0 MVW6200KW0, MVW6230RHW0, MVW6230HC1, MVW6230HW1, MVW6230HC0, MVW6230HW0 WTW8120HC0, WTW8120HW0 WTW7120HC0, WTW7120HW0 WTW6120HC1, WTW6120HW1, WTW6120HW0, WTW6120HC0 WTW5100HC0, WTW5100HW0, WTW5105HW0, WTW5105HC0 Note: This is a distinct lid lock design from other Whirlpool washer latches already in our catalog, such as our W10404050 and W10810403 listings — Whirlpool has used multiple different lid lock designs across its top-load washer lineup over the years. Always verify your full model number before ordering, or match the exact part number printed on your old latch. Contact our support team with your model number if you're unsure. Key Features Genuine Whirlpool OEM part — factory-specified locking mechanism Confirms lid closure to the control board and locks the lid during wash/spin Resolves "lid won't lock," "washer won't start," and "lid pops open mid-cycle" symptoms Superseding design — current replacement for the earlier W11394572 latch Direct drop-in replacement — matches the original mounting and harness connector Replaces W11543566, W11394572, W11032875, AP7219279, and PS17217010 Compatible with Whirlpool, Maytag, and Kenmore top-load washers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number W11700916 Part Type Washer Lid Lock Assembly / Door Latch Condition Genuine OEM Brand Whirlpool Application Top-Load Washers Function Locks the lid during wash/spin and confirms closure to the control board Supersedes W11394572 Repair Difficulty Easy to Moderate — basic hand tools, novice repair experience Quantity 1 lid lock assembly Compatible Brands Whirlpool, Maytag, Kenmore Installation Notes ⚠️ Unplug Washer Before Starting Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Open the washer lid and locate the lid lock assembly mounted on its underside, typically secured with a couple of screws. Photograph the wiring harness connection before disconnecting anything. Remove the mounting screws, disconnect the wiring harness connector from the old assembly, and pull it free. Install the new W11700916 in the same position, reconnect the wiring harness connector fully, and secure the mounting screws. Restore power and run a test cycle to confirm the lid locks securely, the washer starts and completes a full cycle, and the lid unlocks normally once finished. Tools needed: multi-screwdriver, work gloves. Frequently Asked Questions My washer's lid isn't locking properly. Is this the part I need? Yes, this is the classic symptom this assembly addresses. Since the control board won't proceed into the wash or spin cycle without confirmation the lid is closed and locked, a worn or failing lock assembly can prevent the washer from starting or cause it to stop mid-cycle if the lock fails while running. My old part number is W11394572. Is this the same thing? This W11700916 is the current superseding part for W11394572 — Whirlpool has updated the part number, and this is the correct part to order now even if your washer's original latch was labeled with the older number. Is this the same latch as other Whirlpool washer lid locks you sell? Not necessarily — Whirlpool has used several different lid lock designs across its top-load washer lineup over the years, including other designs found elsewhere in our catalog. Always match your exact original part number, or your full washer model number, rather than assuming any "Whirlpool lid lock" will fit your machine. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original locking mechanism and wiring harness configuration of the lid lock assembly designed for your washer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

285751 Washer Genuine Agitator Dog Cam Kit Replaces Part Numbers:  285751, 2837, 3351019, 387092, 3947410, AH334624, EA334624, OEM9283568, AP3094521, PS334624. Description: This Agitator Kit is an OEM replacement part for specific Whirlpool top-loading washer models. Installed in the center of the wash basket, it aids in the mechanical agitation central to regular laundry cleaning.It contains the plastic cam and four plastic dogs needed to repair a malfunctioning or noisy agitator during the wash cycle.   California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

WH03X36897 Washer Genuine OEM Mode Shifter Actuator – Compatible with GE & Hotpoint Washers Product Description Restore proper wash and spin operation with the WH03X36897 Washer Genuine OEM Mode Shifter Actuator. This factory-approved component shifts the washer between agitation and spin modes during the wash cycle. A failing mode shifter can cause the washer to agitate but not spin, spin improperly, make clicking noises, or display cycle errors. Replacing it with this Genuine OEM actuator ensures precise shifting, reliable performance, and correct cycle operation. Replaces Part Numbers WH03X36897, WH18X27186, AP7225424, PD00087767, EAP17626543, PS17626543 Compatibility This Genuine OEM mode shifter actuator fits select GE and Hotpoint top-load washers. Example compatible models include (but are not limited to):GE GTW335ASN1WW, GTW465ASN2WW, GTW485ASJ1WSHotpoint HTW240ASK6WS Always verify your washer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🧩 Genuine OEM Replacement – Factory-certified for exact fit and dependable operation 🔄 Accurate Mode Shifting – Properly switches between wash and spin cycles 🔇 Quiet, Smooth Operation – Reduces clicking or erratic shifting noises 💪 OEM-Grade Durability – Designed for long service life under repeated cycles 🛡️ Fixes Common Issues – Solves no-spin, improper agitation, or cycle errors 📐 Product Specification Part Number: WH03X36897 Component Type: Washer Mode Shifter Actuator Voltage: 120V AC Mounting: Direct-fit installation on transmission assembly Function: Controls agitation-to-spin shifting Compliance: Genuine OEM certified 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver ⚠️ Safety First: Unplug the washer before servicing to avoid electrical shock. Steps: Disconnect power and tilt the washer back for bottom access. Locate the mode shifter actuator near the transmission. Disconnect the wiring harness and remove mounting screws. Install the new WH03X36897 actuator and secure it in place. Reconnect wiring, return washer upright, and restore power. Run a test cycle to confirm proper shifting. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Genuine OEM Replacement Part 🔄 30-Day Return Policy Restore correct washer cycle operation — Add to Cart Now for a factory-quality repair!

Read more less

WH44X10288 Washer Lid Lock and Switch Assembly Replaces Part Numbers: WH44X10288, 1974376, AH3496878, EA3496878, AP5270191, PS3496878. 120V, 60Hz, lid lock and switch assembly. Fits select GE laundry center. Description: This Door Latch Lid Lock is a replacement part for select GE washing machine models. It is designed to securely lock the washing machine's lid or door during operation, ensuring safety and preventing water from spilling during the wash cycle.   This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

Genuine OEM Frigidaire / Electrolux Washer Part 134762010 Washer Genuine OEM Water Level Pressure Switch Monitors air pressure from the washer tub and signals the control system when the correct water level has been reached. Product Overview The Frigidaire 134762010 Washer Water Level Pressure Switch senses changes in air pressure through the washer pressure hose to monitor the amount of water inside the tub. It signals the washer control system when the correct water level has been reached so the appliance can fill, wash, drain, and advance through the cycle correctly. This is a new Genuine OEM Frigidaire / Electrolux replacement part manufactured to the original equipment specifications for proper fit, electrical connection, and operation in compatible washers. Quick Answer 134762010 is a Genuine OEM water-level pressure switch for select Frigidaire, Electrolux, Kenmore, and Crosley front-load washers. It replaces 7134762010. This listing is for the pressure switch only; the pressure hose, clamp, wiring harness, and mounting hardware are not included unless specifically shown. Common Problems This Part May Fix Washer overfills with water Washer does not fill or underfills Incorrect or inconsistent water level Cycle stops or will not advance Washer does not drain or complete the cycle correctly E35 or another water-level-related error on applicable models Replaces and Cross-References 134762010, 1482962, 7134762010, AH2349296, AP4368525, AFR14413, EA2349296, PD00007813, PS2349296. 134762010 is the current manufacturer part number. Other numbers are previous manufacturer or retailer cross-references. Compatibility Designed for select front-load washers manufactured by Electrolux and sold under Frigidaire, Electrolux, Kenmore, and Crosley brand names. Confirmed model examples include: 41741100000 41744130000 EIFLS55IRR0 EIFLS60JIW1 FAFS4473LN0 FAFW3921NW0 FFFW5000QW0 CFW4700LW0 CFW7400QW0 Important: This is a partial compatibility list. Pressure switches can look alike while using different settings, terminals, mounting tabs, or control calibration. Verify the complete washer model number before ordering. Key Features Genuine OEM Frigidaire / Electrolux replacement part Monitors the water level inside the washer tub Signals the control system when the correct fill level is reached Supports proper filling, washing, draining, and cycle operation Snap-tab mounting design on compatible models Designed for original fit and electrical connection Product Specifications Manufacturer Part Number 134762010 Brand Frigidaire / Electrolux Part Type Washer Water Level Pressure Switch Condition New Quality Genuine OEM Application Front-Load Washing Machine Primary Function Senses and controls the washer water level Included One Water Level Pressure Switch Installation Notes Unplug the washer and shut off both water-supply valves. Remove the washer top panel as required for your model. Photograph the wire connector and pressure-hose connection before disconnecting them. Disconnect the electrical connector without pulling on the wires. Release the clamp and carefully remove the pressure hose. Remove the old switch and install the replacement in the same position. Reconnect the hose, clamp, and electrical connector, then reinstall the top panel. Diagnostic tip: Inspect the pressure hose for cracks, pinholes, blockage, moisture, loose connections, or trapped debris. A damaged or obstructed hose can cause the same symptoms as a failed pressure switch. Frequently Asked Questions Is 134762010 a genuine OEM part? Yes. It is a Genuine OEM Frigidaire / Electrolux washer water-level pressure switch. What does the pressure switch do? It monitors air pressure from the washer tub and signals the control system when the correct water level has been reached. Which part number does it replace? It replaces previous manufacturer part number 7134762010. Does this include the pressure hose? No. The listing is for the pressure switch only unless additional components are specifically shown and stated as included. Will it fit every Frigidaire or Electrolux washer? No. Verify the complete appliance model number and required manufacturer part number before purchasing. Shop With Confidence Purchase the correct Genuine OEM replacement part for dependable fit and operation. Verify your washer model number before ordering, and contact our parts team when compatibility assistance is needed. Genuine OEM PartFast U.S. ShippingCompatibility SupportSecure Checkout

Read more less

W11248040 Washer Console (Control Panel Housing) Genuine Whirlpool part Replaces Part Number W11248040, 4845509, W11035013, W11120176, W11192407, PD00087512, EAP12584120, AP6783239, PS12584120. Model Cross Reference This part #W11248040 works with all models listed. Kenmore / Sears 110.27132412 Washer Kenmore / Sears 110.27132413 Washer  

Read more less

AHA75673404 Washer Genuine OEM Drain Pump Replaces Part Numbers: AHA75673404, AHA75673402, AGF30196101, AP6978814, PS12748410 Description: This Drain Pump Assembly is a Genuine OEM part compatible with Specific LG washer models. It is responsible for pumping water out of the washing machine during the drain cycle.  

Read more less