Search results for "washer sensor"

XPARTCO DC31-00187A Washer Drain Pump Motor The XPARTCO DC31-00187A is an aftermarket replacement washer drain pump motor compatible with select Samsung front-load and top-load washers in the WA4, WA5, WF2, WF3, WF4, and WF5 series, as well as select Kenmore washers built on the Samsung platform. The drain pump motor drives the impeller that expels water from the washer tub during the drain phase of each wash cycle. When the motor fails, the washer will not drain, will leave standing water in the tub, stop mid-cycle, or display error codes 5C, SE, SC, 5E, or SUDS. This motor-only assembly includes the pump motor, impeller, and replacement O-ring. Rated 120V, 60Hz, 80W, 1.1A (CL.F), with a 30-minute on / 30-minute off duty cycle. Dimensions: 4-1/4"L x 3"W x 4-1/4"H in gray/white/black plastic, metal, and rubber housing. The DC31-00187A is the motor component that installs into the existing pump housing on compatible Samsung washers — the pump housing (DC97-20621C assembly) is reused from the old pump, making this a motor-only swap rather than a complete pump replacement. It directly replaces DC31-00187D, DC31-00178A, DC31-00178D, PX3516-01, 03DC3100187A, 4958525, AP6977256, EAP9605762, PD00056512, PS9605762, and PS1274262. Installs in 20–30 minutes with basic hand tools. Quick Answer The XPARTCO DC31-00187A Washer Drain Pump Motor fixes Samsung front-load and top-load washers displaying error codes 5C, SE, SC, 5E, or SUDS, not draining, leaving standing water, or making loud noise during the drain cycle. Motor-only assembly — includes motor, impeller, and O-ring; installs into existing pump housing. 120V/60Hz/80W/1.1A/CL.F. 30 min on/30 min off. 4-1/4"L x 3"W x 4-1/4"H. Replaces DC31-00187D, DC31-00178A, DC31-00178D, PX3516-01, 4958525, AP6977256, PS9605762. Compatible with Samsung WA4/WA5/WF2/WF3/WF4/WF5 series. Common Problems This Part Fixes Washer not draining — standing water remaining in the tub after a cycle Error codes 5C, SE, SC, 5E, or SUDS displayed — drain fault detected Washer stopping mid-cycle due to a drain fault Loud humming during the drain phase — motor energized but impeller not turning Grinding or rattling during drain — damaged impeller or worn motor bearings Clothes excessively wet after a cycle — pump not fully removing water before spin Water draining very slowly — motor weakening below rated performance Replaces Part Numbers This drain pump motor directly replaces the following OEM and cross-reference part numbers: DC31-00187A, DC31-00178A, DC31-00178D, 03DC3100187A, ASM654116, EAP9605762, 4958525, AP6977256, PD00056512, PS12742622, PX3516-01. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drain pump motor is compatible with select Samsung front-load and top-load washers from the following series: Samsung top-load washers — WA4 series (WA40J3000AW, WA44A3205AW, WA45H7000AW, WA45M7050AW, WA45N3050AW, WA45T3200AW, WA45R6100AC and related models) Samsung top-load washers — WA5 series (WA50F9A6DSW, WA50M7450AW, WA50R5200AW, WA50R5400AV and related models) Samsung front-load washers — WF2 series (select models) Samsung front-load washers — WF3 series (select models) Samsung front-load washers — WF4 series (WF42H5000AW, WF42H5200AW, WF45M5500AW, WF45N5300AW, WF45R6100AC, WF45T6000AW, WF45A6400AV, WF45B6300AP and related models) Samsung front-load washers — WF5 series (select models) Kenmore / Sears washers (select Samsung-built models) Note: The DC31-00187A is the pump motor only — it installs into the existing pump housing (DC97-20621C assembly) which is retained from the old pump. The housing is not replaced. Check and clean the drain filter before replacing the pump motor — a clogged filter is a common cause of drain errors that doesn't require motor replacement. Key Features Pump motor only — includes motor, impeller, and O-ring; installs into the existing DC97-20621C pump housing retained from the old pump Drives the pump impeller to expel water from the washer tub during the drain cycle Resolves Samsung error codes 5C, SE, SC, 5E, and SUDS caused by drain pump motor failure Rated 120V, 60Hz, 80W, 1.1A (CL.F) — correct specifications for compatible Samsung washers Duty cycle: 30 minutes on / 30 minutes off Dimensions: 4-1/4"L x 3"W x 4-1/4"H Replaces DC31-00187D, DC31-00178A, DC31-00178D, PX3516-01, 4958525, AP6977256, PS9605762, and PS1274262 Compatible with Samsung WA4, WA5, WF2, WF3, WF4, WF5 series and Kenmore Samsung-built washers Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 20–30 minutes with basic hand tools Product Specifications Part Number XPDC31-00187A Also Covers DC31-00187D, DC31-00178A, DC31-00178D (variants) Part Type Washer Drain Pump Motor (Motor Only — reuses existing housing) Condition Aftermarket Replacement Application Samsung Front-Load and Top-Load Washers (WA4/WA5/WF2/WF3/WF4/WF5) Voltage 120V AC Frequency 60 Hz Wattage 80W Amperage 1.1A Duty Class CL.F Duty Cycle 30 minutes on / 30 minutes off Dimensions 4-1/4"L x 3"W x 4-1/4"H Color Gray / White / Black Material Plastic / Metal / Rubber Includes Pump motor, impeller, O-ring Error Codes Resolved 5C, SE, SC, 5E, SUDS Compatible Brands Samsung, Kenmore (Samsung-built) Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting — Wear Gloves Disconnect power and turn off the water supply before beginning. Wear work gloves — there are sharp edges inside the washer cabinet. For front-load models: remove the lower front access panel to expose the pump housing and filter. Drain residual water via the filter drain hose (have a shallow pan ready). Disconnect the wire harness from the motor. On most Samsung front-load models, the motor assembly twists out of the pump housing by rotating counter-clockwise — do not force it. Remove the old motor, note the O-ring position, and install the new O-ring from this kit onto the new DC31-00187A motor. Insert the new motor into the housing and twist clockwise to lock. Reconnect the wire harness. Reinstall the lower panel, restore power and water, and run a drain/spin cycle to confirm drainage. For top-load models: access through the lower front panel or by tilting the washer on its side depending on model. Tools needed: Phillips screwdriver, pliers, shallow pan, towels, work gloves. Frequently Asked Questions What is the difference between DC31-00187A and DC97-20621C? The DC31-00187A is the drain pump motor — the electrical component that drives the impeller. The DC97-20621C is the complete drain pump assembly, which includes the motor plus the outer pump housing, hose connection ports, and mounting hardware. When you order the DC31-00187A, you replace only the motor and reuse the existing DC97-20621C pump housing. When you order the DC97-20621C, you replace the entire assembly including the housing. Both resolve the same drain fault — the DC31-00187A is the more targeted repair when the housing is in good condition. What error codes indicate a drain pump motor failure? Error codes 5C, SE, SC, 5E, and SUDS on compatible Samsung washers all indicate a drain fault — the washer was unable to drain within the expected time. Before replacing the motor, clean the drain filter/coin trap at the lower front panel. A clogged filter is one of the most common causes of these error codes and does not require motor replacement. If the filter is clear and the codes persist, or if the pump is making loud noise or is completely silent during the drain phase, the motor needs replacement. What is the difference between DC31-00187A and DC31-00178A? These are cross-references for the same or very similar Samsung drain pump motor used across different Samsung washer generations. The DC31-00178A was used on earlier Samsung models and the DC31-00187A is the current version. Both are commonly listed as interchangeable replacements for each other in Samsung washer drain pump repair. The DC31-00187D and DC31-00178D are also variants of the same motor from different production runs. Should I clean the filter before replacing the pump motor? Yes — always check and clean the drain filter first. On Samsung front-load washers, the filter is accessible behind the lower front kick panel, typically on the right side — remove the cap slowly and drain water into a shallow pan first. Lint, coins, debris, and hair are very common causes of Samsung drain error codes that are completely resolved by cleaning the filter without any parts replacement. If the filter is clear and the error codes persist, the pump motor is the next component to replace. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured to match the electrical specifications and performance of the original DC31-00187A drain pump motor. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

Genuine OEM Frigidaire / Electrolux Washer Part 134762010 Washer Genuine OEM Water Level Pressure Switch Monitors air pressure from the washer tub and signals the control system when the correct water level has been reached. Product Overview The Frigidaire 134762010 Washer Water Level Pressure Switch senses changes in air pressure through the washer pressure hose to monitor the amount of water inside the tub. It signals the washer control system when the correct water level has been reached so the appliance can fill, wash, drain, and advance through the cycle correctly. This is a new Genuine OEM Frigidaire / Electrolux replacement part manufactured to the original equipment specifications for proper fit, electrical connection, and operation in compatible washers. Quick Answer 134762010 is a Genuine OEM water-level pressure switch for select Frigidaire, Electrolux, Kenmore, and Crosley front-load washers. It replaces 7134762010. This listing is for the pressure switch only; the pressure hose, clamp, wiring harness, and mounting hardware are not included unless specifically shown. Common Problems This Part May Fix Washer overfills with water Washer does not fill or underfills Incorrect or inconsistent water level Cycle stops or will not advance Washer does not drain or complete the cycle correctly E35 or another water-level-related error on applicable models Replaces and Cross-References 134762010, 1482962, 7134762010, AH2349296, AP4368525, AFR14413, EA2349296, PD00007813, PS2349296. 134762010 is the current manufacturer part number. Other numbers are previous manufacturer or retailer cross-references. Compatibility Designed for select front-load washers manufactured by Electrolux and sold under Frigidaire, Electrolux, Kenmore, and Crosley brand names. Confirmed model examples include: 41741100000 41744130000 EIFLS55IRR0 EIFLS60JIW1 FAFS4473LN0 FAFW3921NW0 FFFW5000QW0 CFW4700LW0 CFW7400QW0 Important: This is a partial compatibility list. Pressure switches can look alike while using different settings, terminals, mounting tabs, or control calibration. Verify the complete washer model number before ordering. Key Features Genuine OEM Frigidaire / Electrolux replacement part Monitors the water level inside the washer tub Signals the control system when the correct fill level is reached Supports proper filling, washing, draining, and cycle operation Snap-tab mounting design on compatible models Designed for original fit and electrical connection Product Specifications Manufacturer Part Number 134762010 Brand Frigidaire / Electrolux Part Type Washer Water Level Pressure Switch Condition New Quality Genuine OEM Application Front-Load Washing Machine Primary Function Senses and controls the washer water level Included One Water Level Pressure Switch Installation Notes Unplug the washer and shut off both water-supply valves. Remove the washer top panel as required for your model. Photograph the wire connector and pressure-hose connection before disconnecting them. Disconnect the electrical connector without pulling on the wires. Release the clamp and carefully remove the pressure hose. Remove the old switch and install the replacement in the same position. Reconnect the hose, clamp, and electrical connector, then reinstall the top panel. Diagnostic tip: Inspect the pressure hose for cracks, pinholes, blockage, moisture, loose connections, or trapped debris. A damaged or obstructed hose can cause the same symptoms as a failed pressure switch. Frequently Asked Questions Is 134762010 a genuine OEM part? Yes. It is a Genuine OEM Frigidaire / Electrolux washer water-level pressure switch. What does the pressure switch do? It monitors air pressure from the washer tub and signals the control system when the correct water level has been reached. Which part number does it replace? It replaces previous manufacturer part number 7134762010. Does this include the pressure hose? No. The listing is for the pressure switch only unless additional components are specifically shown and stated as included. Will it fit every Frigidaire or Electrolux washer? No. Verify the complete appliance model number and required manufacturer part number before purchasing. Shop With Confidence Purchase the correct Genuine OEM replacement part for dependable fit and operation. Verify your washer model number before ordering, and contact our parts team when compatibility assistance is needed. Genuine OEM PartFast U.S. ShippingCompatibility SupportSecure Checkout

Read more less

W10335056 Washer Genuine OEM Water Level Switch Pressure Switch Replaces Part Numbers: W10335056, 1617123, 3366846, AH3408073, EA3408073, AP4566382, PS3408073, W10335056VP.  Description: This Pressure Switch is a Genuine OEM part for specific Whirlpool washing machine models. This part ensures your machine fills with the correct amount of water for the selected cycle, preventing overfilling or insufficient water levels that can lead to suboptimal washing results.    A faulty Pressure Switch can result from several issues, including clogging with detergent residue or debris, wear and tear from regular use, or electrical malfunctions affecting its responsiveness.     California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

W11248040 Washer Console (Control Panel Housing) Genuine Whirlpool part Replaces Part Number W11248040, 4845509, W11035013, W11120176, W11192407, PD00087512, EAP12584120, AP6783239, PS12584120. Model Cross Reference This part #W11248040 works with all models listed. Kenmore / Sears 110.27132412 Washer Kenmore / Sears 110.27132413 Washer  

Read more less

XPARTCO DC96-01703G Washer Water Level Pressure Switch - Compatible with Samsung Washers Product Description Ensure accurate water level control in your washer with the replacement XPARTCO DC96-01703G Washer Water Level Pressure Switch. This replacement pressure switch is designed for select Samsung front-load and top-load washers, sensing and controlling water levels for optimal washing performance. It addresses issues like incorrect water levels, not filling, or error codes (e.g., E6 FA), offering a cost-effective alternative to OEM parts. Note: Includes one water level pressure switch. Disconnect power and water supply before installation. Verify compatibility with your washer model. Replaces part numbers: DC96-01703G, PD00026135, EAP4217083, AP5623035, PS4217083. Compatibility: Compatible with models including but not limited to: Samsung: WF42H5000AW/A2, WF42H5200AP/A2, WF42H5400AF/A2, WF45K6200AW/A2, WF45K6500AW/A2, WF45M5500AP/A5, WF45M5500AZ/A5, WF50K7500AV/A2, WF50K7500AW/A2, WF56H9100AG/A2, WF56H9110CW/A2, WF457ARGSG, WW22K6800AW/A2, WV55M9600AW/A5, WV60M9900AV/A5, WD10J6410AW/ZS Other brands: Select models requiring DC96-01703G Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Samsung front-load and top-load washers requiring DC96-01703G. 🔥 Specifications: Precision-engineered water level pressure switch with 28" air pressure hose, designed for accurate water level sensing and control. 💰 Cost-Effective Alternative: Offers OEM-equivalent performance at a lower price. 🛠️ Easy Installation: Requires Phillips screwdriver, work gloves; typically installed in 10–15 minutes. 🛡️ Effective Fixes: Resolves issues like incorrect water levels, not filling, motor idling, or error codes (e.g., E6 FA). Product Specification Part Number: XPDC96-01703G Component Type: Washer water level pressure switch Material: Durable plastic housing with metal contacts Terminal Type: Electrical connector. Operating Conditions: Suitable for high-humidity washer environments Compliance: Prop 65 warning for California Installation Notes: Safety First: Disconnect the washer from the power source and water supply before installation. Tools Needed: Phillips screwdriver, work gloves. Process: Access the switch by removing the top or back panel of the washer, disconnect the old switch’s wiring and hose, install the new switch, and reconnect wiring and hose. Ensure secure connections and test for proper operation. Shop for high-quality replacement appliance parts with a 30-day return policy. Keep your washer running efficiently today! Add to cart now for a budget-friendly fix!

Read more less

XPARTCO W10316760 Refrigerator Thermistor Sensor – Compatible with Whirlpool, Kenmore, Maytag, and KitchenAid Refrigerators Product Description Maintain accurate refrigerator temperature control with the XPARTCO W10316760 Refrigerator Thermistor Sensor. This Refrigerator Thermistor Sensor is a replacement part for select Kenmore, KitchenAid, Maytag, Whirlpool refrigerator models. It is a crucial component responsible for accurately monitoring and regulating the temperature inside the refrigerator and freezer compartments. Replaces Part Numbers W10316760, WPW10323459, W10323459, 12791417, 12791417SP, 12791419SP, 1876627, W10280385, W10280386, W10308052, W10316760VP, W10438639, W10438761, W10452402, AH2580944, EA2580944, PD00006590, EAP2580944, AP4538142, PS2580944,  Compatibility This replacement thermistor sensor fits select Whirlpool, Kenmore, Maytag, Amana, Jenn-Air, and KitchenAid refrigerators. Example compatible models include (but are not limited to): Whirlpool WRS322FDAW04, Maytag MSS25N4MKZ00, and Kenmore 106.51133213. Always verify your refrigerator’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM temperature accuracy and response rate ❄️ Precision Cooling Control – Helps maintain stable refrigerator and freezer temperatures 💰 Affordable Alternative – Cost-effective solution versus expensive OEM sensors 🛠️ Simple Installation – Plug-in design for fast, hassle-free replacement 🛡️ Fixes Common Issues – Solves warm fridge, over-cooling, ice buildup, or erratic temperature cycling 📐 Product Specification Part Number: W10316760 Component Type: Refrigerator Thermistor / Temperature Sensor Material: Plastic probe housing with insulated wiring harness Resistance: ~2.7 kΩ at 77°F (varies with temperature) Mounting: Clips or adhesive tape depending on model location Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, needle-nose pliers (optional) ⚠️ Safety First: Always unplug the refrigerator before performing any repairs to prevent electrical shock. Steps: Disconnect power and remove interior shelves for access. Locate the existing thermistor near the evaporator or liner wall. Disconnect the wiring harness and remove any clips or tape. Install the new XPARTCO W10316760 thermistor in the same location. Reconnect the harness, secure wiring, and reassemble interior panels. Restore power and allow several hours for temperatures to stabilize. ⏱️ Time Required: 10–20 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Restore accurate refrigerator cooling — Add to Cart Now for a reliable, budget-friendly repair!

Read more less

WH11X39237 Genuine OEM GE Washer Drain Pump The WH11X39237 is a Genuine OEM GE replacement drain pump and filter assembly compatible with select GE, GE Profile, and GE 2-in-1 Washer/Dryer Combo front-load washers in the GFW510, GFW550, GFW650, GFW655, GFW850, PFW, and PFQ series. The drain pump is responsible for removing water from the washer drum during the drain and spin cycles — when it fails, the washer will not drain, will leave standing water in the drum, or will produce unusual noises during the drain cycle. This complete drain pump and filter assembly operates at 120V, 60Hz, 1.2A and includes the pump motor, impeller housing, and integrated filter. It directly replaces the discontinued WH11X29539 — WH11X39237 is the current manufacturer-approved updated part number. Also replaces AP6986715, 4962370, B25-3A04, and several additional cross-reference numbers. Installs in 30–45 minutes with basic hand tools. Quick Answer The WH11X39237 Genuine OEM GE Washer Drain Pump fixes GE front-load washers that won't drain, leave standing water in the drum, display drain error codes, or make loud humming or grinding noises during the drain cycle. Complete pump and filter assembly. 120V/60Hz/1.2A. Replaces discontinued WH11X29539. Compatible with GE GFW510, GFW550, GFW650, GFW655, GFW850, PFW, and PFQ series. Common Problems This Part Fixes Washer not draining — standing water remaining in the drum after a cycle Drain error codes displayed on GE front-load washers (e.g. E23, E24, or pump-related codes) Loud humming, grinding, or buzzing noise during the drain cycle Washer stopping mid-cycle due to a drain fault Water leaking from around the drain pump area Drain pump running continuously but water not being expelled Pump impeller jammed by debris and motor burned out Replaces Part Numbers This drain pump directly replaces the following OEM and cross-reference part numbers: WH11X39237, WH11X29539, Hanyu B25-3A04, 9019841, PD00094541, AGE1260100, AP8054992, PS18351790. WH11X39237 is the current manufacturer-approved replacement for the discontinued WH11X29539. If your appliance documentation lists WH11X29539, this is the correct updated part. Compatibility This drain pump is compatible with select front-load washers and laundry combos from the following GE product lines: GE front-load washers — GFW510 series GE front-load washers — GFW550 series GE front-load washers — GFW650 series GE front-load washers — GFW655 series GE front-load washers — GFW850 series GE Profile front-load washers — PFW870, PFW950, PFW955 series GE Profile front-load washers — PFQ83 series GE 2-in-1 Washer/Dryer Combo (select models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Complete drain pump and filter assembly — pump motor, impeller housing, and integrated filter all included Removes water from the drum during drain and spin cycles for proper washer operation Integrated filter traps lint, coins, and debris to prevent pump impeller damage and clogs Electrical specs: 120V, 60Hz, 1.2A — correct for compatible GE front-load models WH11X39237 is the current manufacturer-approved replacement for discontinued WH11X29539 Direct replacement — installs into existing pump housing with no modification required Genuine OEM part manufactured by GE to factory specifications — guaranteed fit and performance Compatible with GFW510, GFW550, GFW650, GFW655, GFW850, PFW, and PFQ series DIY-friendly repair — installs in 30–45 minutes with basic hand tools Product Specifications Part Number WH11X39237 Supersedes WH11X29539 (discontinued) Part Type Washer Drain Pump and Filter Assembly Condition Genuine OEM Application GE Front-Load Washers and 2-in-1 Washer/Dryer Combos Voltage 120V AC Frequency 60 Hz Amperage 1.2A Includes Pump motor, impeller housing, and integrated filter Compatible Series GFW510, GFW550, GFW650, GFW655, GFW850, PFW870, PFW950, PFW955, PFQ83 Compatible Brands GE, GE Profile Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off the water supply before beginning any repair. Place towels and a shallow pan under the pump access area to catch residual water. Remove the front lower access panel of the washer. Before removing the pump, first clean the pump filter (WH23X38617) and check for a clogged filter or debris in the pump housing — a jammed impeller is sometimes mistaken for a failed pump. If the pump motor is confirmed failed, disconnect the wire harness and drain hoses from the old pump assembly, then unscrew or unclip the pump from the mounting bracket. Install the new WH11X39237 pump assembly, reconnect the drain hoses and secure with clamps, reconnect the wire harness, and reinstall the access panel. Restore power and water supply, then run a drain-only cycle to verify proper drainage and check for leaks. Tools needed: Phillips screwdriver, pliers, shallow pan or towels. Frequently Asked Questions What is the difference between WH11X39237 and WH11X29539? These are the same drain pump assembly — WH11X39237 is the current updated part number that GE issued to replace the discontinued WH11X29539. If your washer's documentation, parts diagram, or old pump label shows WH11X29539, the WH11X39237 is the correct replacement to order. Should I check the pump filter before replacing the drain pump? Yes — always check and clean the pump filter (WH23X38617) before replacing the drain pump. A heavily clogged filter can restrict water flow enough to mimic pump failure symptoms, and a foreign object jammed in the impeller can stall the pump motor without permanently damaging it. Remove the filter, clear any debris from the housing and impeller, and test the washer again. If the pump still fails to drain after cleaning, then pump replacement is the next step. How do I know if my drain pump has failed? A failed drain pump typically causes the washer to stop mid-cycle with a drain error code, or to finish a cycle with standing water in the drum. You may also hear a loud humming noise during the drain phase — this indicates the motor is running but the impeller is not turning (jammed or broken). A grinding noise suggests physical damage to the impeller or pump housing. If the pump is completely silent during the drain cycle despite power being delivered to it, the motor has likely burned out. Is the WH11X39237 compatible with GE Profile and GE 2-in-1 models? Yes — the WH11X39237 is compatible with select GE Profile front-load washers in the PFW870, PFW950, PFW955, and PFQ83 series, as well as select GE 2-in-1 Washer/Dryer Combo models. Always verify your specific model number before ordering to confirm compatibility. Is this an OEM or aftermarket part? This is a Genuine OEM part manufactured by GE to factory specifications. It is the exact same drain pump and filter assembly installed in compatible GE and GE Profile front-load washers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

WH12X10614C Washer Genuine Electronic Control Board Replaces Part Number: WH12X10614C, WH12X10614, WH12X10538, AP8056060.

Read more less

DA32-00006W Genuine Samsung OEM Refrigerator Thermistor Refrigerator defrost temperature sensor. Replaces Part Numbers: DA32-10105R, DA32-00006W, DA32-00006U, 2030342, DA32-00006B, DA32-00006C, DA32-00006D, DA32-00006L, DA32-00006M, DA32-00006T, DA32-00006V, AP4135567, PS4138681. The Samsung Defrost Sensor is a genuine part designed specifically for Samsung refrigerators. This sensor, sometimes referred to as a defrost thermostat or defrost temperature sensor, is an integral part of your refrigerator's defrost system.  

Read more less

131758600 Washer Genuine OEM Timer Replaces Part Numbers: 131758600, AP2107583, PS418697. Description: This washer timer is a Genuine OEM part for select Frigidaire washing machine models. This timer controls the various cycles of the washing machine, including wash, rinse, and spin cycles. By regulating the duration and sequence of each cycle, the timer ensures that the washing machine operates smoothly and efficiently.

Read more less

4681EA2001T Genuine OEM LG Washer Drain Pump Motor The 4681EA2001T is a genuine LG OEM drain pump motor for LG and Kenmore front-load washers, and also fits washer/dryer combo units. This motor is responsible for removing water from the washer at the end of the wash and spin cycles, expelling it through the drain hose so the machine can move on to the next stage of the cycle. This part is the motor only — you'll reuse your existing pump housing. It includes the pump impeller, which is not sold separately. Rated 120V-127V, 60Hz, 85W, 1.4A, with a flow rate of 45L per minute. Measures approximately 6.57" x 4.29" x 3.5". As of April 2025, the design of this drain pump motor changed to a gray housing, replacing the earlier black housing — this is expected and doesn't affect fit or function. Common failure causes include a worn or seized motor and general electrical wear. Symptoms of a failing drain pump motor include the washer not draining, unusual noise during the drain cycle, an OE error code, or leaking near the pump if the motor fails while still under load. It directly replaces 4681EA2001D, 4681EA2001U, 4681EA2001N, 4681EA1007G, 4681EA1007D, LP2001T, AP5328388, 2003273, 1468049, DP040-038, EAP3523278, EAP3579318, and 5214FR4006L. Quick Answer The 4681EA2001T Genuine OEM LG Washer Drain Pump Motor fixes LG and Kenmore front-load washers (and washer/dryer combos) that aren't draining, are making unusual noise during the drain cycle, or are showing an OE error code. 120V-127V, 60Hz, 85W, 1.4A, 45L/min. Replaces 4681EA2001D, 4681EA2001U, 4681EA2001N, 4681EA1007G, 4681EA1007D, LP2001T, AP5328388, 2003273, 1468049, DP040-038, EAP3523278, EAP3579318, 5214FR4006L. This is the motor only — reuse your existing pump housing when installing. As of April 2025, the new housing color is gray instead of the older black; this is a normal design change and not a compatibility issue. Common Problems This Part Fixes Washer not draining — standing water left in the tub after a cycle Unusual noise during the drain cycle OE error code displayed on the control panel Washer taking longer than normal to drain Leaking near the pump area Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer drain pump motor directly replaces the following OEM and cross-reference part numbers: 4681EA2001T, 4681EA1007G, 2003273, 4681EA1007D, 4681EA2001D, 4681EA2001N, 4681EA2001U, DP040-038, ALG51292, AH3579318, EA3579318, PD00001722, EAP3579318, AP5328388, PS3579318 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drain pump motor is compatible with select LG front-load washers, and also fits select Kenmore Elite washers built on the LG platform, and washer/dryer combo units, including model numbers such as WM2101HW, WM3270CW, WM3431HS, WM3770HVA, WM3001HWA, WM8000HVA, WM8000HWA, WM2550HRCA, WM2550HWCA, GCW1069CS, WM3550HWCA, WM3070HRA, WM4070HVA, WM3070HWA, WM2350HRC, WM3360HVCA, WM2350HWC, GCW1069QS, WM2650HRA, WM3360HRCA, WM3360HWCA, WM3150HVC, WM2650HWA, WM2655HVA, WM3885HCCA, WM3150HWC, WM3885HWCA, WM2250CW, WM2450HRA, WM3987HW, WM3470HVA, WM3470HWA, LSWF388HVS, WM3550HVCA, WM2455HG, WM2277HB, WM2487HRMA, and Kenmore 79641072310. Note: Always verify your full model number before ordering, since LG uses several different drain pump designs across its washer lineup. Contact our support team with your model number if you're unsure. Key Features Genuine LG OEM part — factory-specified motor design and impeller Pumps wastewater out of the tub through the drain hose Resolves "not draining," "unusual noise during drain," and "OE error code" symptoms caused by motor failure Includes pump impeller (not sold separately) Reuses your existing pump housing — motor only Rated 120V-127V, 60Hz, 85W, 1.4A, 45L/min flow rate Direct drop-in replacement matching the original mounting and connections Replaces 4681EA2001D, 4681EA2001U, 4681EA2001N, 4681EA1007G, 4681EA1007D, LP2001T, AP5328388, 2003273, 1468049, DP040-038, EAP3523278, EAP3579318, and 5214FR4006L Compatible with LG and Kenmore front-load washers and washer/dryer combo units Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number 4681EA2001T Part Type Washer Drain Pump Motor Condition Genuine OEM Brand LG Application Front-Load Washers, Washer/Dryer Combos Voltage 120V-127V Frequency 60 Hz Wattage 85 W Amperage 1.4 A Flow Rate 45 L/min Dimensions Approx. 6.57" x 4.29" x 3.5" Housing Not included — reuse existing pump housing Housing Color (as of April 2025) Gray (previously black) Repair Difficulty Medium — 30 to 60 minutes Quantity 1 drain pump motor Compatible Brands LG, Kenmore Installation Notes ⚠️ Unplug Washer And Shut Off Water Supply Before Starting — Have Towels Ready For Draining Water Disconnect power at the outlet or shut off the circuit breaker, and shut off the water supply before beginning. Wear work gloves. Lay towels down in front of the washer before starting, and have a pail ready. Remove the detergent drawer and check the drain filter (bottom lower left panel door) to confirm it's clean and the drain line isn't blocked before assuming the motor is at fault. Many customers find it easier to access the pump from underneath by carefully laying the washer on its back — be prepared for a significant amount of additional water to drain out onto the floor once you do this, so keep towels close by. With access to the pump, disconnect the electrical connector from the old motor and separate the motor from the pump housing, which you'll reuse with the new motor. Attach the new 4681EA2001T motor to your existing pump housing, transferring the impeller setup as needed. Reconnect the electrical connector fully. Stand the washer back upright, reinstall the detergent drawer, and reconnect the water supply and power. Test the new pump to confirm it drains properly before considering the repair complete. Tools needed: Phillips screwdriver, locking pliers, needle nose pliers, small flathead screwdriver, towels, work gloves. Frequently Asked Questions My washer shows an OE error code and isn't draining. Is this the part I need? Likely yes. An OE error code on LG washers is commonly tied to a drain issue, and a bad drain pump motor is one of the most frequent causes. Before replacing the motor, it's worth checking that the drain filter and coin trap (if your model has one) are clean and that the drain line itself isn't blocked, since those are simpler and cheaper things to rule out first. Does this come with the pump housing? No, this is the motor only, and it includes the pump impeller, which isn't sold separately. You'll reuse your existing pump housing during installation rather than replacing it as part of this repair. The new motor's housing looks a different color than I expected. Did I get the wrong part? No, this is expected. As of April 2025, LG changed the design of this drain pump motor to use a gray housing in place of the earlier black housing. This is a normal manufacturing update and doesn't affect fit or function. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by LG to factory specifications — guaranteed fit, materials, and performance. It matches the original motor design, impeller, and electrical rating of the drain pump motor originally installed in your washer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

W11396717 Genuine OEM Whirlpool Washer Drain Pump Assembly The W11396717 is a Genuine OEM Whirlpool replacement drain pump assembly compatible with select Whirlpool, Maytag, and Kenmore high-efficiency top-load washers — including the Whirlpool WTW5100, WTW6120, WTW7120, WTW8120, and WTW8127 series, and the Maytag MVW6200, MVW6230, MVW7230, MVW7232, and MVW8230 series. The drain pump removes water from the washer tub during the drain portion of each wash cycle. When the pump fails, the washer will not drain, will leave standing water in the tub, stop mid-cycle, or make loud humming, grinding, or rattling noises during the drain phase. Rated 120V, 60Hz, 1.2A (CL.F duty class), this complete pump assembly is mounted to the underside of the outer tub and secured by three mounting screws. It directly replaces the earlier W11263349 as well as 4960510, AP6974116, PS12731177, and EAP12731177. Note: the pump is accessed from the bottom of the washer — the machine must be tilted or laid on its back to reach the mounting screws. Installs in 20–35 minutes with basic hand tools. Quick Answer The W11396717 Genuine OEM Whirlpool Washer Drain Pump fixes Whirlpool and Maytag HE top-load washers that won't drain, leave standing water, stop mid-cycle, or make loud noise during the drain cycle. 120V/60Hz/1.2A CL.F. Mounted on the underside of the outer tub — access by tilting the washer. Replaces W11263349, 4960510, AP6974116, PS12731177, EAP12731177. Compatible with Whirlpool WTW5100/6120/7120/8120/8127 and Maytag MVW6200/6230/7230/7232/8230 series top-load washers. Common Problems This Part Fixes Washer not draining — standing water remaining in the tub after a cycle Washer stopping mid-cycle due to a drain fault Loud humming during the drain phase — motor energized but pump not moving water Grinding or rattling during drain — damaged impeller or worn bearings Clothes excessively wet after a full cycle — pump not fully removing water before spin Water draining very slowly — pump motor weakening below rated performance Water leaking from the pump area underneath the washer Replaces Part Numbers This drain pump directly replaces the following OEM and cross-reference part numbers: W11396717, W11263349, Hanyu B25-3A04, AP6974116, AWP44690, EAP12731177, PD00065247, PS12731177 W11396717 is the current production part number superseding W11263349. If your parts diagram shows W11263349, the W11396717 is the correct current replacement. Contact our support team if you need confirmation before ordering. Compatibility This drain pump is compatible with select HE top-load washers from the following brands and series: Whirlpool top-load washers — WTW5100HC0, WTW5100HW0, WTW5105HC0, WTW5105HW0, WTW6120HC0, WTW6120HW0, WTW7120HC0, WTW7120HC1, WTW7120HW0, WTW8120HC0, WTW8120HW0, WTW8127LC1, WTW8127LW0, WTW8127LW1 and related models Maytag top-load washers — MVW6200KW0, MVW6230HC0, MVW6230HW0, MVW6230RHW0, MVW7230HC0, MVW7230HC1, MVW7230HW0, MVW7230HW1, MVW7232HC0, MVW7232HC1, MVW7232HC2, MVW7232HW0, MVW7232HW1, MVW7232HW2, MVW8230HC0, 7MMVW7230LC0, 7MMVW7230LW0 and related models Kenmore / Sears top-load washers — 11021112021, 11021652020, 11031652020 and related models Note: This pump is mounted on the underside of the outer tub and requires tilting or laying the washer on its back for access. Always verify your model number before ordering. Key Features Removes water from the tub during drain and spin cycles for proper washer operation Rated 120V, 60Hz, 1.2A (CL.F) — correct electrical specifications for compatible HE top-load washers Current production part — directly supersedes W11263349 Mounted on the underside of the outer tub and secured by three mounting screws — tilt or lay washer on its back for access Replaces W11263349, 4960510, AP6974116, PS12731177, EAP12731177, and B25-3A04 Compatible with Whirlpool WTW5100/6120/7120/8120/8127 and Maytag MVW6200/6230/7230/7232/8230 series top-load washers Genuine OEM part manufactured by Whirlpool to factory specifications — guaranteed fit and performance DIY repair — installs in 20–35 minutes with basic hand tools Product Specifications Part Number W11396717 Supersedes W11263349 Part Type HE Top-Load Washer Drain Pump Assembly Condition Genuine OEM Application Whirlpool / Maytag / Kenmore HE Top-Load Washers Voltage 120V AC Frequency 60 Hz Amperage 1.2A Duty Class CL.F Mounting 3 screws on underside of outer tub — tilt washer for access Compatible Brands Whirlpool, Maytag, Kenmore Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting — Work Gloves Recommended Disconnect power and turn off the water supply before beginning. Wear work gloves throughout. The drain pump is mounted on the underside of the outer tub — to access it, disconnect the water supply hoses, drain hose, and lid switch wiring, then carefully tilt the washer onto its back or side on a padded surface. Locate the pump on the bottom of the tub. Using a 5/16" nut driver, remove the three mounting screws securing the pump assembly to the tub. Release the two spring clamps with channel-lock pliers and disconnect the inlet and outlet hoses from the pump. Disconnect the wiring harness and remove the old pump. Install the new W11396717 pump in the same position, reconnect hoses and clamps, reconnect the wiring harness, and secure with the three mounting screws. Return the washer to upright, reconnect all hoses and wiring, restore power and water, and run a drain/spin cycle to confirm drainage and check for leaks. Tools needed: Phillips screwdriver, 5/16" nut driver, channel-lock pliers, padded surface for tilting, work gloves. Frequently Asked Questions What is the difference between W11396717 and W11263349? These are the same drain pump assembly across two production revisions. W11263349 was the original part number, and W11396717 is the current updated version that supersedes it. Whirlpool issues updated part numbers when minor engineering changes are made during production. Both are the same pump with the same specifications, dimensions, and function. If your washer's parts diagram shows W11263349, the W11396717 is the correct current replacement to order. Why does accessing this pump require tilting the washer? On compatible Whirlpool WTW and Maytag MVW HE top-load washers, the drain pump is mounted directly to the underside of the outer tub — not on the cabinet side panel or behind a front access panel as on some other models. The pump's three mounting screws are only reachable from below the machine. The standard repair procedure is to unplug and disconnect the washer, tilt it onto its back or side on a padded surface, access the pump from underneath, and return the washer to upright after installation. How do I know if it's the drain pump versus a blocked drain hose? Before replacing the pump, check the drain hose for kinks or blockages — disconnect the hose and blow through it to confirm it is clear. Also check whether the drain hose standpipe height is within the recommended range (typically 39–96 inches from the floor). If the hose is clear and properly positioned but the washer still won't drain, listen during the drain phase: a completely silent drain cycle (motor not running) suggests a failed motor or control board issue, while a humming or grinding noise during drain confirms the pump motor is receiving power but the pump is mechanically failed and needs replacement. Is this pump the same as the W10876600 used in older Whirlpool Cabrio models? No — the W11396717 and the W10876600 are different drain pumps for different Whirlpool top-load washer generations. The W10876600 (and its successor WPW10730972) is used in older Whirlpool Cabrio and Maytag Centennial models. The W11396717 is used in newer WTW5100/6120/7120/8120 and MVW6200/6230/7230/7232/8230 series models. They are not interchangeable — verify your model number before ordering. Is this an OEM or aftermarket part? This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It is the exact same drain pump assembly installed in compatible Whirlpool, Maytag, and Kenmore top-load washers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less