XPARTCO XPDC60X5-450R Dual Run Capacitor (60/5 MFD, 450V, Round)
The XPARTCO XPDC60X5-450R is a universal dual run capacitor for central air conditioners, heat pumps, and condensing units. A run capacitor works alongside a single-phase AC motor to keep it running efficiently once it's started, boosting torque and correcting the phase of the current feeding the motor's windings. This is a dual capacitor, meaning it combines two separate capacitors — one for the compressor, one for the condenser fan motor — into a single three-terminal can, which is why nearly every residential outdoor AC unit uses exactly this style of component to run both motors from one part.
Rated 60 MFD for the compressor circuit and 5 MFD for the fan motor circuit, at 450VAC, in a round aluminum can housing. Because a capacitor's voltage rating is a ceiling rather than a fixed match, this 450V-rated capacitor can safely replace an original capacitor rated 370V or 440V — going higher on voltage is always safe, going lower is not. Over time, the dielectric material inside a run capacitor breaks down from heat cycling and electrical stress, causing it to lose capacitance or fail outright. A failing dual capacitor produces a very recognizable set of symptoms: the outdoor unit hums but the compressor or fan won't start, the fan spins slowly or needs a manual push to get going, the system trips the breaker, or the capacitor can itself is visibly bulging, domed, or leaking oily residue at the top.
Quick Answer
The XPARTCO XPDC60X5-450R Dual Run Capacitor fixes central air conditioners and heat pumps where the outdoor unit hums but won't start, the compressor or fan motor won't run, the fan spins slowly or needs a manual push, the breaker trips, or the capacitor can is visibly bulged or leaking. 60 MFD (compressor) + 5 MFD (fan) dual capacitor, 450VAC, round, 3-terminal. Universal fit for equipment originally speced at 370V or 440V, since a higher voltage rating is always a safe upgrade. Capacitors store a dangerous electrical charge even after power is disconnected — always discharge before handling.
Common Problems This Part Fixes
Outdoor AC unit hums but the compressor won't start
Condenser fan won't spin, or spins slowly and needs a manual push to get going
System trips the breaker shortly after starting
AC blows warm air because the compressor isn't running
Repeated clicking sound from the contactor as it tries and fails to start the motor
Capacitor can visibly bulging, domed on top, or leaking oily residue
System that used to start slowly and has now stopped starting altogether
Burning smell from the outdoor unit's electrical compartment
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
XPDC60X5-450R
This is a universal component rather than a single-manufacturer part, so the specific OEM number your HVAC system's label references will vary by brand (Goodman, Trane, Carrier, Rheem, York, Lennox, Amana, and others). This capacitor is a correct replacement for any dual run capacitor matching the 60 MFD / 5 MFD rating with a voltage rating of 450V or lower. If you have your original part number, contact our support team and we will verify compatibility before you order.
Compatibility
This dual run capacitor is a universal replacement compatible with central air conditioners, heat pumps, and condensing units across all major HVAC brands, wherever the original capacitor is rated:
60 MFD (compressor) + 5 MFD (fan motor)
370V, 440V, or 450V (this capacitor's 450V rating exceeds and safely replaces either lower rating)
Round can shape with 3 terminals
Note: The MFD (microfarad) rating must match your original capacitor exactly on both sides — do not substitute a different MFD value for either the compressor or fan side. Voltage rating, on the other hand, can be equal to or higher than the original (450V safely replaces 370V or 440V), but never lower. Can shape (round vs. oval) affects only physical fit inside your unit's electrical compartment, not performance. If you're unsure of your original capacitor's specifications, they're printed directly on its can — contact our support team if you'd like help confirming compatibility.
Key Features
Universal dual run capacitor — supports both the compressor and condenser fan motor from one component
60 MFD compressor rating + 5 MFD fan motor rating in a single 3-terminal can
450VAC rating — a safe upgrade replacement for equipment originally speced at 370V or 440V
Round aluminum can construction
Resolves "hums but won't start," "fan spins slowly," "trips the breaker," and "bulging or leaking can" symptoms caused by capacitor failure
1/4" quick-connect terminals for a direct plug-on fit to standard HVAC wiring
50/60Hz rated
Safety approved: CQC, VDE, TÜV, and CL; built to GB/T 3667 and EN 60252 standards
Built to meet or exceed industry-standard specifications for this capacitor class
Product Specifications
Part Number
XPDC60X5-450R
Part Type
Dual Run Capacitor
Condition
New — Universal Replacement Part
Capacitance — Compressor
60 MFD (µF)
Capacitance — Fan Motor
5 MFD (µF)
Voltage Rating
450VAC
Shape
Round
Terminals
3 (1/4" quick-connect)
Frequency
50/60 Hz
Tolerance
±5%
Construction Type
Polypropylene film capacitor
Operating Temperature Range
-40°C to 70°C (-40°F to +158°F)
Safety Approvals
CQC, VDE, TÜV, CL
Approval Standard
GB/T 3667, EN 60252
Application
Central Air Conditioners, Heat Pumps, Condensing Units
Quantity
1 dual run capacitor
Compatible Brands
Universal — all major HVAC brands
Installation Notes
⚠️ Danger — Capacitors Store A Dangerous Electrical Charge Shut off power to the outdoor unit at the disconnect box and at the breaker before beginning. A capacitor stores an electrical charge even after power has been disconnected, and that charge can deliver a serious or fatal shock. Before touching any terminal, discharge the capacitor by shorting each pair of terminals together (C-to-Fan, C-to-Herm, and Fan-to-Herm) using an insulated-handle screwdriver, or by using a proper capacitor discharge tool with a resistor. Never short the terminals with a bare metal tool held with your bare hand. If you are not fully comfortable performing a capacitor discharge safely, have a qualified HVAC technician replace this part instead.
⚠️ Photograph The Wiring Before Disconnecting — Match Terminals Exactly Wear work gloves and safety glasses. After confirming the capacitor is fully discharged, photograph the wiring on the old capacitor's terminals before disconnecting anything — dual capacitors are labeled C (Common), Herm or Comp (compressor/hermetic), and Fan, and getting a wire on the wrong terminal can damage the new capacitor or the motor it feeds. Note which terminal each wire came from, or label them individually with tape. Remove the mounting strap or bracket holding the old capacitor in its housing, and disconnect each wire from its terminal. Install the new XPDC60X5-450R in the same mounting position, secure it with the strap or bracket, and reconnect each wire to the matching terminal (C, Herm, and Fan) exactly as labeled. Double-check every connection before restoring power. Restore power at the breaker and disconnect box, and confirm the compressor and fan both start promptly and run smoothly. Tools needed: insulated-handle screwdriver or capacitor discharge tool, nut driver, work gloves, safety glasses.
Frequently Asked Questions
My AC unit hums but won't start. Is this the capacitor?
It's one of the most common causes of exactly that symptom. A run capacitor gives the compressor or fan motor the extra push needed to start turning; without it, the motor can draw power and hum in place without ever actually starting to spin. If you can see the capacitor can and it looks bulged, domed on top, or is leaking a brown oily residue, that's strong visual confirmation of failure.
Can I use a 450V capacitor to replace my old 370V or 440V one?
Yes. Voltage rating is a ceiling, not an exact match requirement — a capacitor rated for a higher voltage than your original will work safely and often lasts longer under the same electrical stress. What you cannot do is go the other direction: never install a capacitor with a lower voltage rating than your original, since that risks premature failure or the capacitor breaking down under normal operating conditions.
Does the round vs. oval shape matter?
Only for physical fit inside your unit's electrical compartment — it has no effect on electrical performance. If your unit's mounting bracket or available space is sized for a round can, use a round capacitor; if it's sized for an oval can, use an oval one. The MFD and voltage ratings are what matter electrically, not the shape.
The fan spins if I give it a push, but won't start on its own. What does that mean?
This is a classic sign of a weak or failing capacitor — it may still have enough charge to keep the motor running once it's already spinning, but not enough to provide the initial starting torque. This is a strong signal to replace the capacitor before it fails completely and leaves you with no cooling at all.
Is this a genuine OEM part?
This is a universal replacement part rather than a brand-specific OEM part. Because dual run capacitors are a standardized component defined by their electrical specifications rather than their manufacturer, this capacitor is a correct replacement for any unit's original capacitor that shares the same 60/5 MFD, 450VAC, round dual run capacitor rating — regardless of which HVAC brand originally installed it.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Quality Replacement Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
WR49X25197 Refrigerator Genuine OEM Axial Evaporator Motor Replaces WR60X26866
The WR49X25197 is a genuine GE OEM axial evaporator fan motor for the fresh food evaporator on select GE French door refrigerators. Unlike a standard evaporator fan motor, this is an axial-design motor purpose-built for the fresh food side of the refrigeration system, using its blade geometry to move air efficiently and quietly through that compartment's evaporator coil for precise, consistent temperature control.
Rated 13.6VDC, 0.16A. Manufactured by Nidec, designation V80E14MS2A3-57A611. Over time, motor bearings wear out or the motor can fail electrically, and symptoms typically include the fresh food compartment running warm while the freezer remains unaffected, unusual noise from the fresh food evaporator area, or inconsistent cooling in that compartment specifically, since this motor doesn't serve the freezer side at all. It directly replaces WR60X26866, WR60X10341, WR60X24303, WR60X26033, WR60X10356, WR60X10357, WR60X26030, 239D1412P001, 239D1412P006, and AP6278228.
Quick Answer
The WR49X25197 Genuine OEM GE Axial Evaporator Motor fixes GE French door refrigerators where the fresh food compartment specifically runs warm, there's unusual noise from the fresh food evaporator area, or fresh food cooling is inconsistent while the freezer works fine. 13.6VDC, 0.16A axial motor. Replaces WR60X26866, WR60X10341, WR60X24303, WR60X26033, WR60X10356, WR60X10357, WR60X26030, 239D1412P001, 239D1412P006, AP6278228. If your refrigerator was manufactured between May 2014 and March 2015 (serial range HD–FF), the control software must also be updated by factory service or a Software Update Module (WR98R882802) for this motor to perform correctly.
Common Problems This Part Fixes
Fresh food compartment running warm while the freezer stays normal
Unusual noise coming from the fresh food evaporator area
Inconsistent or fluctuating temperature in the fresh food section specifically
Fresh food evaporator fan not spinning or spinning intermittently
Reduced airflow affecting fresh food cooling performance
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This refrigerator axial evaporator motor directly replaces the following OEM and cross-reference part numbers:
WR49X25197, WR60X26866, WR02X13733, WR60X10341, WR60X10356, WR60X10357, WR60X24303, WR60X26030, WR60X26033, V80E14MS2A3-57A611, 8817V W1, 239D1412P006, PD00038765, FIX12172983, AGE29673, AP6278228, PS12172983
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This axial evaporator motor is compatible with select GE French door refrigerators.
Note — fresh food evaporator only, and a software caveat for certain units: This motor serves the fresh food evaporator specifically — a different application from a general freezer evaporator fan motor. Additionally, if your refrigerator was manufactured between May 2014 and March 2015 (serial range HD through FF), the refrigerator's control software must be updated by factory service, or with a Software Update Module (WR98R882802), for this motor to perform correctly after installation. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure.
Key Features
Genuine GE OEM part — factory-specified axial blade design for the fresh food evaporator
Resolves "fresh food running warm," "unusual noise from the fresh food evaporator," and "inconsistent fresh food cooling" symptoms
Rated 13.6VDC, 0.16A
Manufactured by Nidec, designation V80E14MS2A3-57A611
Direct drop-in replacement matching the original mounting and blade fitment
Replaces WR60X26866, WR60X10341, WR60X24303, WR60X26033, WR60X10356, WR60X10357, WR60X26030, 239D1412P001, 239D1412P006, and AP6278228
Compatible with GE French door refrigerators
Genuine OEM replacement — guaranteed fit, materials, and performance
Product Specifications
Part Number
WR49X25197
OEM Part Number
WR60X26866
Part Type
Axial Evaporator Fan Motor (Fresh Food)
Condition
Genuine OEM
Brand
GE
Application
French Door Refrigerators — Fresh Food Evaporator
Voltage
13.6VDC
Amperage
0.16A
Motor Manufacturer
Nidec (V80E14MS2A3-57A611)
Motor Type
Axial
Software Update Caveat
Required for units mfg. May 2014–March 2015, serial range HD–FF (WR98R882802)
Quantity
1 evaporator motor
Compatible Brand
GE
Installation Notes
⚠️ Unplug Refrigerator Before Starting — Check Your Manufacture Date For A Software Update Requirement Disconnect power at the outlet before beginning, and move perishable food to a cooler for the duration of the repair. Wear work gloves. Before starting, check your refrigerator's serial number/manufacture date sticker (typically inside the fresh food compartment) — if your unit was made between May 2014 and March 2015 with a serial range of HD through FF, plan for a control software update via factory service or a Software Update Module (WR98R882802) after installing this motor, since without it the new motor may not perform correctly. Access to the fresh food evaporator is typically through an interior panel in the fresh food compartment, separate from the freezer's evaporator access — check your model's service diagram. If there's frost or ice buildup around the fan or coil, let the unit sit unplugged with the door open for a few hours before continuing. Photograph the wiring harness connector and the fan blade's orientation before disconnecting anything. Unplug the wiring harness connector from the old motor, remove the mounting screws or clips holding the motor bracket in place, and pull the motor and fan blade assembly free. Mount the new WR49X25197 in the same position, reconnect the wiring harness connector fully, and confirm the blade spins freely by hand without contacting the housing before reassembling the panel. Restore power and monitor the fresh food compartment over the next 24 hours to confirm even, consistent cooling has returned. Tools needed: Phillips screwdriver, work gloves.
Frequently Asked Questions
My fresh food section runs warm but the freezer is fine. Is this the right part?
Yes, this is exactly the symptom pattern this motor addresses, since it's dedicated specifically to the fresh food evaporator rather than serving both compartments. If your freezer is cooling normally and only the fresh food section is warm or inconsistent, this axial motor is a strong candidate for the cause.
Do I really need a software update after installing this motor?
Only if your refrigerator falls into a specific manufacturing window: units made between May 2014 and March 2015, identifiable by a serial range of HD through FF. For those units, GE's own guidance states the control software must be updated by factory service or with a Software Update Module (WR98R882802) for the new motor to perform correctly. If your refrigerator falls outside that date range, this step isn't necessary — check your serial number sticker to confirm which category your unit falls into.
Is this the same as a regular evaporator fan motor?
Not quite — this is an axial-design motor built specifically for the fresh food evaporator on GE French door refrigerators, distinct from general evaporator fan motors that serve the freezer side or both compartments together. Always confirm your model number and which compartment's fan has failed before ordering.
Is this an OEM or aftermarket part?
This is a genuine OEM part, manufactured by GE to factory specifications — guaranteed fit, materials, and performance. It matches the original axial motor design, blade fitment, and electrical rating of the fresh food evaporator motor originally installed in your refrigerator.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
XPARTCO DC31-00187A Washer Drain Pump Motor
The XPARTCO DC31-00187A is an aftermarket replacement washer drain pump motor compatible with select Samsung front-load and top-load washers in the WA4, WA5, WF2, WF3, WF4, and WF5 series, as well as select Kenmore washers built on the Samsung platform. The drain pump motor drives the impeller that expels water from the washer tub during the drain phase of each wash cycle. When the motor fails, the washer will not drain, will leave standing water in the tub, stop mid-cycle, or display error codes 5C, SE, SC, 5E, or SUDS.
This motor-only assembly includes the pump motor, impeller, and replacement O-ring. Rated 120V, 60Hz, 80W, 1.1A (CL.F), with a 30-minute on / 30-minute off duty cycle. Dimensions: 4-1/4"L x 3"W x 4-1/4"H in gray/white/black plastic, metal, and rubber housing. The DC31-00187A is the motor component that installs into the existing pump housing on compatible Samsung washers — the pump housing (DC97-20621C assembly) is reused from the old pump, making this a motor-only swap rather than a complete pump replacement. It directly replaces DC31-00187D, DC31-00178A, DC31-00178D, PX3516-01, 03DC3100187A, 4958525, AP6977256, EAP9605762, PD00056512, PS9605762, and PS1274262. Installs in 20–30 minutes with basic hand tools.
Quick Answer
The XPARTCO DC31-00187A Washer Drain Pump Motor fixes Samsung front-load and top-load washers displaying error codes 5C, SE, SC, 5E, or SUDS, not draining, leaving standing water, or making loud noise during the drain cycle. Motor-only assembly — includes motor, impeller, and O-ring; installs into existing pump housing. 120V/60Hz/80W/1.1A/CL.F. 30 min on/30 min off. 4-1/4"L x 3"W x 4-1/4"H. Replaces DC31-00187D, DC31-00178A, DC31-00178D, PX3516-01, 4958525, AP6977256, PS9605762. Compatible with Samsung WA4/WA5/WF2/WF3/WF4/WF5 series.
Common Problems This Part Fixes
Washer not draining — standing water remaining in the tub after a cycle
Error codes 5C, SE, SC, 5E, or SUDS displayed — drain fault detected
Washer stopping mid-cycle due to a drain fault
Loud humming during the drain phase — motor energized but impeller not turning
Grinding or rattling during drain — damaged impeller or worn motor bearings
Clothes excessively wet after a cycle — pump not fully removing water before spin
Water draining very slowly — motor weakening below rated performance
Replaces Part Numbers
This drain pump motor directly replaces the following OEM and cross-reference part numbers:
DC31-00187A, DC31-00178A, DC31-00178D, 03DC3100187A, ASM654116, EAP9605762, 4958525, AP6977256, PD00056512, PS12742622, PX3516-01.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This drain pump motor is compatible with select Samsung front-load and top-load washers from the following series:
Samsung top-load washers — WA4 series (WA40J3000AW, WA44A3205AW, WA45H7000AW, WA45M7050AW, WA45N3050AW, WA45T3200AW, WA45R6100AC and related models)
Samsung top-load washers — WA5 series (WA50F9A6DSW, WA50M7450AW, WA50R5200AW, WA50R5400AV and related models)
Samsung front-load washers — WF2 series (select models)
Samsung front-load washers — WF3 series (select models)
Samsung front-load washers — WF4 series (WF42H5000AW, WF42H5200AW, WF45M5500AW, WF45N5300AW, WF45R6100AC, WF45T6000AW, WF45A6400AV, WF45B6300AP and related models)
Samsung front-load washers — WF5 series (select models)
Kenmore / Sears washers (select Samsung-built models)
Note: The DC31-00187A is the pump motor only — it installs into the existing pump housing (DC97-20621C assembly) which is retained from the old pump. The housing is not replaced. Check and clean the drain filter before replacing the pump motor — a clogged filter is a common cause of drain errors that doesn't require motor replacement.
Key Features
Pump motor only — includes motor, impeller, and O-ring; installs into the existing DC97-20621C pump housing retained from the old pump
Drives the pump impeller to expel water from the washer tub during the drain cycle
Resolves Samsung error codes 5C, SE, SC, 5E, and SUDS caused by drain pump motor failure
Rated 120V, 60Hz, 80W, 1.1A (CL.F) — correct specifications for compatible Samsung washers
Duty cycle: 30 minutes on / 30 minutes off
Dimensions: 4-1/4"L x 3"W x 4-1/4"H
Replaces DC31-00187D, DC31-00178A, DC31-00178D, PX3516-01, 4958525, AP6977256, PS9605762, and PS1274262
Compatible with Samsung WA4, WA5, WF2, WF3, WF4, WF5 series and Kenmore Samsung-built washers
Aftermarket replacement built to OEM-equivalent quality standards
DIY repair — installs in 20–30 minutes with basic hand tools
Product Specifications
Part Number
XPDC31-00187A
Also Covers
DC31-00187D, DC31-00178A, DC31-00178D (variants)
Part Type
Washer Drain Pump Motor (Motor Only — reuses existing housing)
Condition
Aftermarket Replacement
Application
Samsung Front-Load and Top-Load Washers (WA4/WA5/WF2/WF3/WF4/WF5)
Voltage
120V AC
Frequency
60 Hz
Wattage
80W
Amperage
1.1A
Duty Class
CL.F
Duty Cycle
30 minutes on / 30 minutes off
Dimensions
4-1/4"L x 3"W x 4-1/4"H
Color
Gray / White / Black
Material
Plastic / Metal / Rubber
Includes
Pump motor, impeller, O-ring
Error Codes Resolved
5C, SE, SC, 5E, SUDS
Compatible Brands
Samsung, Kenmore (Samsung-built)
Installation Notes
⚠️ Unplug Washer and Shut Off Water Before Starting — Wear Gloves Disconnect power and turn off the water supply before beginning. Wear work gloves — there are sharp edges inside the washer cabinet. For front-load models: remove the lower front access panel to expose the pump housing and filter. Drain residual water via the filter drain hose (have a shallow pan ready). Disconnect the wire harness from the motor. On most Samsung front-load models, the motor assembly twists out of the pump housing by rotating counter-clockwise — do not force it. Remove the old motor, note the O-ring position, and install the new O-ring from this kit onto the new DC31-00187A motor. Insert the new motor into the housing and twist clockwise to lock. Reconnect the wire harness. Reinstall the lower panel, restore power and water, and run a drain/spin cycle to confirm drainage. For top-load models: access through the lower front panel or by tilting the washer on its side depending on model. Tools needed: Phillips screwdriver, pliers, shallow pan, towels, work gloves.
Frequently Asked Questions
What is the difference between DC31-00187A and DC97-20621C?
The DC31-00187A is the drain pump motor — the electrical component that drives the impeller. The DC97-20621C is the complete drain pump assembly, which includes the motor plus the outer pump housing, hose connection ports, and mounting hardware. When you order the DC31-00187A, you replace only the motor and reuse the existing DC97-20621C pump housing. When you order the DC97-20621C, you replace the entire assembly including the housing. Both resolve the same drain fault — the DC31-00187A is the more targeted repair when the housing is in good condition.
What error codes indicate a drain pump motor failure?
Error codes 5C, SE, SC, 5E, and SUDS on compatible Samsung washers all indicate a drain fault — the washer was unable to drain within the expected time. Before replacing the motor, clean the drain filter/coin trap at the lower front panel. A clogged filter is one of the most common causes of these error codes and does not require motor replacement. If the filter is clear and the codes persist, or if the pump is making loud noise or is completely silent during the drain phase, the motor needs replacement.
What is the difference between DC31-00187A and DC31-00178A?
These are cross-references for the same or very similar Samsung drain pump motor used across different Samsung washer generations. The DC31-00178A was used on earlier Samsung models and the DC31-00187A is the current version. Both are commonly listed as interchangeable replacements for each other in Samsung washer drain pump repair. The DC31-00187D and DC31-00178D are also variants of the same motor from different production runs.
Should I clean the filter before replacing the pump motor?
Yes — always check and clean the drain filter first. On Samsung front-load washers, the filter is accessible behind the lower front kick panel, typically on the right side — remove the cap slowly and drain water into a shallow pan first. Lint, coins, debris, and hair are very common causes of Samsung drain error codes that are completely resolved by cleaning the filter without any parts replacement. If the filter is clear and the error codes persist, the pump motor is the next component to replace.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured to match the electrical specifications and performance of the original DC31-00187A drain pump motor.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
Genuine OEM WB26X44167 Wall Oven Convection Motor Kit
The Genuine OEM GE WB26X44167 is the convection motor kit for select GE wall ovens. The motor spins the convection fan blade that circulates hot air through the oven cavity for even heating. When it wears out, airflow weakens, the oven gets noisy, and convection performance drops.
This is the original GE part, not an aftermarket equivalent. It is sold as a kit. Check your model number before ordering.
Quick Answer
The Genuine OEM WB26X44167 Convection Motor Kit replaces the convection fan motor on a compatible GE wall oven when it has failed. Replaces WB26T10069, WB26X21763, WB26X23476, WB26X27929 and WB26X31224. Classic symptoms: no convection heat, uneven baking, weak airflow, or a noisy oven fan.
Common Problems This Part Fixes
No convection heat, or the convection fan not working
Uneven baking
Weak airflow or declining convection performance
Increased noise from the oven fan
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This convection motor kit replaces or supersedes the following part numbers:
WB26X44167, WB26X23476, WB26X27929, WB26X31224, WB26T10069, WB26X21763, AGE22636, AP7193683, OEM21581058, EAP16742591, PD00089141, PS16742591
If your old motor shows a different number, contact our support team and we'll check whether it matches.
Compatibility
This convection motor kit is listed for GE, GE Profile and Café wall ovens, including these examples:
GE CT9050EK2DS, CT9050SH1SS, CT9070SH1SS
GE CT9550EK2DS, CT9550SH1SS, CT9570SL1SS
GE CTD70DM2N2S5, CTD70DP2N1S1
GE PT7550DF2BB, PT7550EH1ES, PCT7050DF2BB
Note: The models above are a sample, not a full list. GE sells several convection motor kits with different part numbers. Check your full model number against your parts diagram, or contact our support team to verify fit before ordering.
Key Features
Genuine OEM GE part, not an aftermarket equivalent
Drives the convection fan that circulates hot air for even heating
Replaces five earlier GE convection motor part numbers
Sold as a kit
Product Specifications
Part Number
WB26X44167
OEM Part Number
WB26X44167
Part Type
Wall Oven Convection Motor Kit
Condition
Genuine OEM
Manufacturer
GE
Quantity
1 Kit
Application
Select GE Wall Ovens
Installation Notes
⚠️ Disconnect Power Before Installing Shut off the oven's circuit breaker or unplug the oven before you begin, let the oven cool, and wear work gloves. Remove the oven's rear cover per your model's service guide to reach the motor, disconnect the wire connector, and remove the old motor. Install the new motor, reconnect the wiring, refit the cover, restore power, and run a convection cycle to confirm the fan runs quietly.
Frequently Asked Questions
My oven fan is noisy or not turning. Is this the part I need?
It can be. With the oven off and cool, turn the fan blade by hand. If it is hard to turn, the motor bearings may be worn. A multimeter continuity check on the motor can confirm a failed motor.
Is this an OEM or aftermarket part?
This is a genuine OEM part from GE, not an aftermarket equivalent.
What is in the kit?
It is sold as a convection motor kit. Retailers do not itemize the contents, so contact our support team if you need to confirm them before ordering.
Will this fit my wall oven?
It is listed for many GE wall oven models, but the model list above is only a sample. Check your full model number against your parts diagram, or contact our support team and we'll verify it before you order.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout
Genuine Whirlpool OEM
Whirlpool WPW10184813 Refrigerator Genuine OEM Ice Dispenser Motor
Genuine OEM ice-dispenser door motor for select Whirlpool-built refrigerators.
Product Overview
The Whirlpool WPW10184813 Refrigerator Ice Dispenser Door Motor is a Genuine Whirlpool OEM replacement part. It opens and closes the ice chute door during dispenser operation so ice can pass through the chute and the door can reseal afterward.
A failed motor can cause the dispenser door to remain stuck open or closed, prevent ice from dispensing correctly, or allow warm room air to enter the chute area.
Quick Answer
WPW10184813 is the Genuine Whirlpool OEM ice-dispenser door motor that replaces W10184813 and 2305262. Verify the complete refrigerator model number before purchase.
Common Problems This Part May Fix
Ice dispenser door will not open
Ice chute door will not close
Ice maker makes ice but ice will not dispense
Chute door sticks or operates intermittently
Warm air enters around the dispenser chute
Frost or moisture develops around the dispenser opening
Replaces and Cross-References
WPW10184813, 1489085, 2305262, AP6016508, EAP11749796, W10184813, AWP49407, OEM18049533, PD00006398, PS11749796
Cross-reference numbers are provided for identification. Always verify compatibility by complete refrigerator model number.
Compatibility
Used on select Whirlpool-built refrigerators sold under Whirlpool, KitchenAid, JennAir, Maytag, and Kenmore brand names. Compatible model examples include:
GI7FVCXWY00
KSCS25FTMS02
KSRS25FTSS01
KSCS23FVMS02
KSRS25RSBT01
KSCS25FVMS01
KSCS25FTSS00
GC3NHAXVA00
106.56702500
Important: This is only a partial model list. Confirm the complete model number from the refrigerator identification label before ordering.
Key Features
Genuine Whirlpool OEM part
Operates the ice dispenser chute door
Replaces W10184813 and 2305262
For select Whirlpool-built side-by-side and French-door refrigerators
Helps restore proper dispenser-door opening and closing
Product Specifications
Manufacturer Part Number
WPW10184813
Brand
Whirlpool
Part Type
Refrigerator Ice Dispenser Door Motor
Condition
New
Quality
Genuine OEM
Application
Ice Dispenser Chute Door
Package Quantity
1 Motor
Installation Notes
Disconnect refrigerator power before service.
Remove the dispenser trim and front components according to the appliance service procedure.
Photograph connector and mechanical linkage positions before disassembly.
Inspect the chute door, hinge, spring, and linkage for binding or damage before replacing the motor.
Transfer or reconnect the wiring and linkage exactly as originally installed.
Reassemble all dispenser parts and verify the chute door opens and fully closes before returning the refrigerator to service.
Diagnostic tip: A dispenser that will not release ice can also be caused by an actuator, dispenser switch, control board, auger motor, frozen chute, or mechanical obstruction. Diagnose the dispenser system before replacing parts.
Frequently Asked Questions
Is WPW10184813 a Genuine Whirlpool OEM part?
Yes. WPW10184813 is a Genuine Whirlpool OEM ice-dispenser door motor.
Does it replace W10184813?
Yes. Whirlpool lists WPW10184813 as the replacement for W10184813 and 2305262.
What does this motor do?
It opens and closes the dispenser chute door so ice can pass through the chute and the opening can reseal after dispensing.
Will it fit every Whirlpool refrigerator?
No. Verify the complete refrigerator model number before ordering because dispenser designs vary by model and production revision.
Shop With Confidence
Genuine Whirlpool OEM replacement part. Verify your complete refrigerator model and original part number before ordering.
Genuine OEMIce Dispenser MotorCompatibility SupportFast U.S. Shipping
XPARTCO XPDC70X5-450R Dual Run Capacitor (70/5 MFD, 450V, Round)
The XPARTCO XPDC70X5-450R is a universal dual run capacitor for central air conditioners, heat pumps, and condensing units. A run capacitor works alongside a single-phase AC motor to keep it running efficiently once it's started, boosting torque and correcting the phase of the current feeding the motor's windings. This is a dual capacitor, meaning it combines two separate capacitors — one for the compressor, one for the condenser fan motor — into a single three-terminal can, which is why nearly every residential outdoor AC unit uses exactly this style of component to run both motors from one part.
Rated 70 MFD for the compressor circuit and 5 MFD for the fan motor circuit, at 450VAC, in a round aluminum can housing. Because a capacitor's voltage rating is a ceiling rather than a fixed match, this 450V-rated capacitor can safely replace an original capacitor rated 370V or 440V — going higher on voltage is always safe, going lower is not. Over time, the dielectric material inside a run capacitor breaks down from heat cycling and electrical stress, causing it to lose capacitance or fail outright. A failing dual capacitor produces a very recognizable set of symptoms: the outdoor unit hums but the compressor or fan won't start, the fan spins slowly or needs a manual push to get going, the system trips the breaker, or the capacitor can itself is visibly bulging, domed, or leaking oily residue at the top.
Quick Answer
The XPARTCO XPDC70X5-450R Dual Run Capacitor fixes central air conditioners and heat pumps where the outdoor unit hums but won't start, the compressor or fan motor won't run, the fan spins slowly or needs a manual push, the breaker trips, or the capacitor can is visibly bulged or leaking. 70 MFD (compressor) + 5 MFD (fan) dual capacitor, 450VAC, round, 3-terminal. Universal fit for equipment originally speced at 370V or 440V, since a higher voltage rating is always a safe upgrade. Capacitors store a dangerous electrical charge even after power is disconnected — always discharge before handling.
Common Problems This Part Fixes
Outdoor AC unit hums but the compressor won't start
Condenser fan won't spin, or spins slowly and needs a manual push to get going
System trips the breaker shortly after starting
AC blows warm air because the compressor isn't running
Repeated clicking sound from the contactor as it tries and fails to start the motor
Capacitor can visibly bulging, domed on top, or leaking oily residue
System that used to start slowly and has now stopped starting altogether
Burning smell from the outdoor unit's electrical compartment
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
XPDC70X5-450R
This is a universal component rather than a single-manufacturer part, so the specific OEM number your HVAC system's label references will vary by brand (Goodman, Trane, Carrier, Rheem, York, Lennox, Amana, and others). This capacitor is a correct replacement for any dual run capacitor matching the 70 MFD / 5 MFD rating with a voltage rating of 450V or lower. If you have your original part number, contact our support team and we will verify compatibility before you order.
Compatibility
This dual run capacitor is a universal replacement compatible with central air conditioners, heat pumps, and condensing units across all major HVAC brands, wherever the original capacitor is rated:
70 MFD (compressor) + 5 MFD (fan motor)
370V, 440V, or 450V (this capacitor's 450V rating exceeds and safely replaces either lower rating)
Round can shape with 3 terminals
Note: The MFD (microfarad) rating must match your original capacitor exactly on both sides — do not substitute a different MFD value for either the compressor or fan side. Voltage rating, on the other hand, can be equal to or higher than the original (450V safely replaces 370V or 440V), but never lower. Can shape (round vs. oval) affects only physical fit inside your unit's electrical compartment, not performance. If you're unsure of your original capacitor's specifications, they're printed directly on its can — contact our support team if you'd like help confirming compatibility.
Key Features
Universal dual run capacitor — supports both the compressor and condenser fan motor from one component
70 MFD compressor rating + 5 MFD fan motor rating in a single 3-terminal can
450VAC rating — a safe upgrade replacement for equipment originally speced at 370V or 440V
Round aluminum can construction
Resolves "hums but won't start," "fan spins slowly," "trips the breaker," and "bulging or leaking can" symptoms caused by capacitor failure
1/4" quick-connect terminals for a direct plug-on fit to standard HVAC wiring
50/60Hz rated
Safety approved: CQC, VDE, TÜV, and CL; built to GB/T 3667 and EN 60252 standards
Built to meet or exceed industry-standard specifications for this capacitor class
Product Specifications
Part Number
XPDC70X5-450R
Part Type
Dual Run Capacitor
Condition
New — Universal Replacement Part
Capacitance — Compressor
70 MFD (µF)
Capacitance — Fan Motor
5 MFD (µF)
Voltage Rating
450VAC
Shape
Round
Terminals
3 (1/4" quick-connect)
Frequency
50/60 Hz
Tolerance
±5%
Construction Type
Polypropylene film capacitor
Operating Temperature Range
-40°C to 70°C (-40°F to +158°F)
Safety Approvals
CQC, VDE, TÜV, CL
Approval Standard
GB/T 3667, EN 60252
Application
Central Air Conditioners, Heat Pumps, Condensing Units
Quantity
1 dual run capacitor
Compatible Brands
Universal — all major HVAC brands
Installation Notes
⚠️ Danger — Capacitors Store A Dangerous Electrical Charge Shut off power to the outdoor unit at the disconnect box and at the breaker before beginning. A capacitor stores an electrical charge even after power has been disconnected, and that charge can deliver a serious or fatal shock. Before touching any terminal, discharge the capacitor by shorting each pair of terminals together (C-to-Fan, C-to-Herm, and Fan-to-Herm) using an insulated-handle screwdriver, or by using a proper capacitor discharge tool with a resistor. Never short the terminals with a bare metal tool held with your bare hand. If you are not fully comfortable performing a capacitor discharge safely, have a qualified HVAC technician replace this part instead.
⚠️ Photograph The Wiring Before Disconnecting — Match Terminals Exactly Wear work gloves and safety glasses. After confirming the capacitor is fully discharged, photograph the wiring on the old capacitor's terminals before disconnecting anything — dual capacitors are labeled C (Common), Herm or Comp (compressor/hermetic), and Fan, and getting a wire on the wrong terminal can damage the new capacitor or the motor it feeds. Note which terminal each wire came from, or label them individually with tape. Remove the mounting strap or bracket holding the old capacitor in its housing, and disconnect each wire from its terminal. Install the new XPDC70X5-450R in the same mounting position, secure it with the strap or bracket, and reconnect each wire to the matching terminal (C, Herm, and Fan) exactly as labeled. Double-check every connection before restoring power. Restore power at the breaker and disconnect box, and confirm the compressor and fan both start promptly and run smoothly. Tools needed: insulated-handle screwdriver or capacitor discharge tool, nut driver, work gloves, safety glasses.
Frequently Asked Questions
My AC unit hums but won't start. Is this the capacitor?
It's one of the most common causes of exactly that symptom. A run capacitor gives the compressor or fan motor the extra push needed to start turning; without it, the motor can draw power and hum in place without ever actually starting to spin. If you can see the capacitor can and it looks bulged, domed on top, or is leaking a brown oily residue, that's strong visual confirmation of failure.
Can I use a 450V capacitor to replace my old 370V or 440V one?
Yes. Voltage rating is a ceiling, not an exact match requirement — a capacitor rated for a higher voltage than your original will work safely and often lasts longer under the same electrical stress. What you cannot do is go the other direction: never install a capacitor with a lower voltage rating than your original, since that risks premature failure or the capacitor breaking down under normal operating conditions.
Does the round vs. oval shape matter?
Only for physical fit inside your unit's electrical compartment — it has no effect on electrical performance. If your unit's mounting bracket or available space is sized for a round can, use a round capacitor; if it's sized for an oval can, use an oval one. The MFD and voltage ratings are what matter electrically, not the shape.
The fan spins if I give it a push, but won't start on its own. What does that mean?
This is a classic sign of a weak or failing capacitor — it may still have enough charge to keep the motor running once it's already spinning, but not enough to provide the initial starting torque. This is a strong signal to replace the capacitor before it fails completely and leaves you with no cooling at all.
Is this a genuine OEM part?
This is a universal replacement part rather than a brand-specific OEM part. Because dual run capacitors are a standardized component defined by their electrical specifications rather than their manufacturer, this capacitor is a correct replacement for any unit's original capacitor that shares the same 70/5 MFD, 450VAC, round dual run capacitor rating — regardless of which HVAC brand originally installed it.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Quality Replacement Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
XPARTCO 4681EA2001T Washer Drain Pump Motor
The XPARTCO 4681EA2001T is an aftermarket replacement drain pump motor assembly compatible with a wide range of LG and Kenmore front-load washers. The drain pump motor forces water out of the washer drum through the drain hose during and after the wash and spin cycles — when it fails, the washer will not drain, will display an OE error code, leave standing water in the drum, or produce a loud humming or grinding noise during the drain phase.
This drain pump motor is rated at 120V–127V, 60Hz, 85W, 1.4A with a flow rate of 45 liters per minute and a spin speed of 1,100–1,200 RPM. It is made from durable metal and ABS plastic and includes the pump impeller and a removable filter housing with sealing ring for quieter, smoother operation. Note: this is the motor assembly only — it reuses the existing pump housing from your washer. It directly replaces 4681EA2001N, 4681EA1007G, 4681EA1007D, AP5328388, and several additional cross-reference numbers. Installs in 30–60 minutes with basic hand tools.
Quick Answer
The XPARTCO 4681EA2001T Washer Drain Pump Motor fixes LG and Kenmore front-load washers showing OE error codes, not draining, leaving standing water, or making loud humming or grinding sounds during the drain cycle. Rated 120V–127V/60Hz/85W/1.4A, 45L/min, 1,100–1,200 RPM. Includes impeller and removable filter housing. Motor assembly only — reuses existing pump housing. Replaces 4681EA2001N, AP5328388, 4681EA1007G, and more.
Common Problems This Part Fixes
OE error code displayed — washer cannot drain within the allotted time
Washer not draining — standing water remaining in the drum after a cycle
Loud humming or buzzing during the drain cycle — motor running but impeller not turning
Grinding or rattling noise during draining — physical damage to pump components
Washer stopping mid-cycle due to a drain fault
Washer draining very slowly — worn pump motor below rated flow
Water leaking from the drain pump area
Replaces Part Numbers
This drain pump motor directly replaces the following OEM and cross-reference part numbers:
4681EA2001T, 4681EA1007G, 2003273, 4681EA1007D, 4681EA2001D, 4681EA2001N, 4681EA2001U, DP040-038, ALG51292, AH3579318, EA3579318, PD00001722, EAP3579318, AP5328388, PS3579318.
4681EA2001T is the current updated part number — it is the manufacturer-approved replacement for the older 4681EA2001N. If your washer or parts diagram shows 4681EA2001N, order 4681EA2001T.
Compatibility
This drain pump motor is compatible with select front-load washers from the following brands:
LG front-load washers — WM2xxx, WM3xxx, WM4xxx, WM5xxx, WM8xxx, WM9xxx series
Kenmore / Sears front-load washers (select LG-built models, including 796-series)
Important: This is the pump motor assembly only — it installs into your washer's existing pump housing. The pump housing is not included and is reused from your old assembly. Always verify your model number before ordering. Contact our support team if you're unsure.
Key Features
Forces water out of the drum through the drain hose during wash and spin cycles at 45 liters per minute
Rated 120V–127V, 60Hz, 85W, 1.4A — correct electrical specifications for compatible LG and Kenmore models
Spin speed: 1,100–1,200 RPM for powerful, efficient drainage
Includes pump impeller and removable filter housing with sealing ring
Removable filter housing allows easy cleaning without full pump disassembly
Sealing ring reduces vibration and noise during operation
Durable metal and ABS plastic construction — built to withstand repeated high-volume drainage cycles
Motor assembly only — installs into existing pump housing, no housing replacement needed
Resolves OE error code on compatible LG and Kenmore front-load washers
Aftermarket replacement built to OEM-equivalent quality standards
DIY repair — installs in 30–60 minutes with basic hand tools
Product Specifications
Part Number
4681EA2001T
Also Replaces
4681EA2001N (updated current replacement)
Part Type
Washer Drain Pump Motor Assembly
Condition
Aftermarket Replacement
Application
LG and Kenmore Front-Load Washers
Voltage
120V – 127V AC
Frequency
60 Hz
Wattage
85W
Amperage
1.4A
Flow Rate
45 liters per minute
Spin Speed
1,100 – 1,200 RPM
Material
Metal / ABS Plastic
Includes
Motor assembly, impeller, removable filter housing, sealing ring
Note
Motor assembly only — existing pump housing is reused
Compatible Brands
LG, Kenmore
Installation Notes
⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off the water supply before beginning any repair. Place towels and a shallow pan at the front of the washer to catch residual water. Open the small access panel at the lower front of the washer and drain any remaining water through the drain hose or filter port. Remove the front panel of the washer by unscrewing the top panel screws, then removing the door gasket retaining wire and door latch screws to free the front panel. With the front panel removed, the drain pump assembly is now visible at the lower front. Use a flat-head screwdriver to release the pump mounting clip, then disconnect the drain hoses using pliers to loosen the clamps. Disconnect the wire harness from the pump motor. Pull the motor assembly out of the pump housing. Install the new 4681EA2001T motor into the existing housing, reconnect the hoses and wire harness, secure the pump clip, and reassemble the front panel. Restore power and water supply, then run a drain/spin cycle to verify proper drainage. Tools needed: Phillips screwdriver, flat-head screwdriver, needle-nose pliers, slip-joint pliers, shallow pan.
Frequently Asked Questions
What is the difference between 4681EA2001T and 4681EA2001N?
These are the same drain pump motor — 4681EA2001T is the updated current part number that replaced the older 4681EA2001N. LG issued the updated number during a production cycle revision. If your washer or its documentation shows 4681EA2001N, 4681EA2001D, or any other older variant, the 4681EA2001T is the correct replacement to order.
What does the OE error code mean on an LG washer?
OE (or OE error) stands for "Outlet Error" — it means the washer was unable to drain within the expected time. Common causes include a clogged drain filter, a blocked or kinked drain hose, or a failed drain pump motor. Before replacing the motor, check and clean the drain filter and inspect the drain hose for kinks or blockages. If both are clear and the washer still shows OE, the pump motor has likely failed and needs replacement.
Does this include the pump housing?
No — the 4681EA2001T is the motor assembly only. It installs into your washer's existing pump housing, which is not included and does not need to be replaced in most cases. If your pump housing is cracked or damaged, you will need to source it separately. In most repairs, the housing is reused and only the motor assembly is replaced.
Should I check the drain filter before replacing the pump motor?
Yes — always check and clean the drain filter first. LG front-load washers have a coin trap and filter at the lower front that should be cleaned regularly. A heavily clogged filter or a foreign object jammed in the impeller can cause OE errors and loud humming without the pump motor being permanently damaged. Remove the filter, clear debris from the impeller area, and test the washer. If the problem persists after cleaning, the motor is the likely culprit.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine LG OEM part, but is manufactured from durable metal and ABS plastic to match the electrical specifications and performance of the original 4681EA2001T drain pump motor assembly.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
5040JA2004A Genuine OEM LG Refrigerator Motor Damper Grommet (Rear)
The 5040JA2004A is a genuine LG OEM rubber motor damper grommet for LG and select Kenmore refrigerators. This small rubber component mounts and isolates a fan motor from the surrounding bracket, cushioning it against vibration as the motor runs. This is the rear-position grommet; LG refrigerators typically use more than one grommet to support a fan motor from multiple points.
Made of rubber, this grommet naturally degrades over years of exposure to cold temperatures and constant vibration, eventually cracking, hardening, or losing its cushioning shape. Once it fails, the motor it supports is no longer properly isolated, and the metal motor bracket can end up in direct contact with the surrounding housing. A worn or failed grommet typically shows up as new or worsening rattling, buzzing, or vibration noise coming from the back of the refrigerator, especially noticeable when the fan motor is running. It directly replaces 5040JA2004B, 1268010, AP4635690, AH3526229, EA3526229, PS3526229, EAP3526229, and PD00027884.
Quick Answer
The 5040JA2004A Genuine OEM LG Refrigerator Motor Damper Grommet (Rear) fixes LG and select Kenmore refrigerators with new or worsening rattling, buzzing, or vibration noise from the back of the unit, especially when the fan motor is running. Rubber, rear-position grommet. Replaces 5040JA2004B, 1268010, AP4635690, AH3526229, EA3526229, PS3526229, EAP3526229, PD00027884. This grommet is used with a fan motor at the rear of the refrigerator; sources vary on whether that's the evaporator or condenser fan depending on the specific model, so confirm your model number before ordering.
Common Problems This Part Fixes
Rattling or buzzing noise from the back of the refrigerator
Vibration noise that's especially noticeable when the fan motor is running
Noise that has gradually worsened over time
Visibly cracked, hardened, or flattened rubber grommet
Motor bracket that feels loose or vibrates excessively against its housing
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This motor damper grommet directly replaces the following OEM and cross-reference part numbers:
5040JA2004A, 1268010, AP4635690, AH3526229, EA3526229, PS3526229, EAP3526229, PD00027884
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This motor damper grommet is compatible with select LG refrigerators, and also fits select Kenmore refrigerators built on the LG platform, including model numbers such as LSXS26386S00, LTCS20030S/00, LTC24380SB00, LRSCS21935SW, LFC24770ST/02, LSXS26326W/01, and Kenmore 795.79043311, 795.51089011, 795.51832412, 795.79412810, and 795.78032211.
Note: This is the rear-position grommet. LG also lists a related grommet, part number 5040JA2009B, used as a support damper for fan motors on other models — the two are not necessarily interchangeable, so confirm your exact part number and position before ordering. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure.
Key Features
Genuine LG OEM part — factory-specified rubber compound and fit
Isolates the fan motor from its bracket, cushioning it against vibration
Resolves "rattling," "buzzing," and "vibration noise" symptoms caused by a worn or failed grommet
Rear-position grommet
Durable rubber construction designed for the refrigerator's cold operating environment
Direct drop-in replacement — no tools required on most models
Replaces 5040JA2004B, 1268010, AP4635690, AH3526229, EA3526229, PS3526229, EAP3526229, and PD00027884
Compatible with LG and select Kenmore refrigerators
Genuine OEM replacement — guaranteed fit, materials, and performance
Product Specifications
Part Number
5040JA2004A
Part Type
Fan Motor Damper Grommet — Rear
Condition
Genuine OEM
Brand
LG
Material
Rubber
Function
Isolates and cushions a fan motor from vibration at its bracket
Position
Rear
Related Part
5040JA2009B (support damper, different position/models — verify before substituting)
Repair Difficulty
Very Easy — typically no tools required
Quantity
1 damper grommet
Compatible Brands
LG, Kenmore
Installation Notes
⚠️ Unplug Refrigerator Before Starting Disconnect power at the outlet before beginning, and move perishable food to a cooler if access requires opening the freezer compartment. Wear work gloves. Access depends on your model — this grommet supports a fan motor that may be located behind the freezer's rear interior panel or in the compressor/machine compartment at the back or bottom of the unit, so check your model's service diagram for the exact location. Remove any panel screws needed to reach the motor bracket. Photograph the grommet's position and how it seats against the bracket before removing it. Gently remove the old, worn grommet from around the motor mounting post — it typically pulls or presses off without tools. Press the new 5040JA2004A grommet into the same position, seating it fully so it cushions the motor bracket evenly. Reassemble any panels removed for access, restore power, and run the refrigerator for a while to confirm the rattling or vibration noise has resolved. Tools needed: Phillips screwdriver (for panel access), work gloves.
Frequently Asked Questions
My refrigerator has developed a rattling noise from the back. Is this the grommet?
Yes, this is a common cause of exactly that symptom. Once the rubber grommet cracks, hardens, or loses its cushioning shape, the fan motor's mounting bracket is no longer properly isolated and can vibrate directly against the surrounding housing, producing a rattling or buzzing noise — especially noticeable whenever the fan motor is actively running.
Is this for the evaporator fan motor or the condenser fan motor?
Sources describe this grommet's application somewhat differently depending on the specific refrigerator model — some reference it as supporting the evaporator fan motor, others the condenser fan motor. In practice, this reflects that LG uses the same grommet design for fan motor mounting in more than one location depending on the model. Confirm your full model number against the compatibility list, or check your appliance's parts diagram, to be certain which motor this grommet supports on your specific unit.
Do I need any tools to replace this?
The grommet itself is tool-free — it simply presses into place around the motor mounting post. You will likely need a screwdriver to remove whatever panel is covering the area where the motor and grommet are located, but the grommet swap itself requires no tools.
Is this an OEM or aftermarket part?
This is a genuine OEM part, manufactured by LG to factory specifications — guaranteed fit, materials, and performance. It matches the original rubber compound and mounting fit of the motor damper grommet originally installed in your refrigerator.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
134196602CM Dryer Drive Motor
120V, 60Hz, 1/4 HP, main motor
Fits Specific Frigidaire dryer Models.
Replaces Part Numbers:134196602, 134196600, 134196601, AP6783327, PS12584805.
This is an aftermarket part that can be used as a replacement for the OEM part.
California Residents only
WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov
XPARTCO DD31-00016A Dishwasher Drain Pump Motor
The XPARTCO DD31-00016A is an aftermarket replacement BLDC (brushless DC) drain pump motor for Samsung dishwashers. This motor removes water from the dishwasher tub during the drain phase of the cycle — an impeller mechanism pumps water out through the drain hose, running during the draining phase to ensure a constant, steady flow and help prevent clogs.
Weighs approximately 0.50 lbs, with package dimensions of 4.02" x 3.50" x 3.54". Compatible with 120V and 230V systems. Common causes of failure include worn motor bearings, electrical failure, or debris obstructing the impeller. Symptoms of a failing drain pump motor include water not draining from the tub, standing water left after a cycle, unusual noise during the drain phase, or intermittent draining problems that don't happen every cycle. It directly replaces AP5917178, 113121, 4000925, EAP9606350, PS9606350, ASM773863, PD00036475, and 045900194701.
Quick Answer
The XPARTCO DD31-00016A Dishwasher Drain Pump Motor fixes Samsung dishwashers that aren't draining, leave standing water after a cycle, make unusual noise during draining, or have intermittent draining problems. BLDC motor, 120V/230V, ~0.50 lbs. Replaces AP5917178, 113121, 4000925, EAP9606350, PS9606350, ASM773863, PD00036475, 045900194701. When removing the old motor, you'll need to hold a release tab open while twisting the motor counterclockwise at the same time — this two-handed step trips up a lot of first-time installers.
Common Problems This Part Fixes
Dishwasher not draining water from the tub
Standing water left in the tub after a completed cycle
Unusual noise during the drain phase
Intermittent draining problems that don't occur every cycle
Reduced water circulation and cleaning performance
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This dishwasher drain pump motor directly replaces the following OEM and cross-reference part numbers:
DD31-00016A, 113121, 4000925, AP5917178, ASM773863, EAP9606350, PD00036475, PS9606350
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This drain pump motor is compatible with select Samsung dishwashers, including model numbers such as DW80R9950QH/AA, DW80B7070UG/AA, DW80R9950MT/AA, DW80B6061UG/AA, DW80R9950QN/AA, DW80B7070US/AA, DW80B6061US/AA, DW80B7071UG/AA, DW80B6060US/AA, DW80B6060UG/AA, DW80BB7070U1/AA, DW80B7070AP/AA, DW80B7071US/AA, DW80R7061UG/AA, DDW24T999BB/DA, DDW24M999UM/DA, DDW24T998US/DA, DDW24M999US/DA, DW60M9990AP, and DW80B6060UG.
Note: This part is not a replacement for any earlier designation — per Samsung's own listing, DD31-00016A is a new part that doesn't supersede another part number. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure.
Key Features
Aftermarket replacement BLDC (brushless DC) drain pump motor
Resolves "won't drain," "standing water," "unusual noise," and "intermittent draining" symptoms
Impeller mechanism pumps water out through the drain hose to prevent clogs
Compatible with 120V and 230V systems
Direct drop-in replacement matching the original mounting and connections
Replaces AP5917178, 113121, 4000925, EAP9606350, PS9606350, ASM773863, PD00036475, and 045900194701
Compatible with Samsung dishwashers
Aftermarket replacement built to OEM-equivalent quality standards
Typical repair takes 30 to 60 minutes
Product Specifications
Part Number
XPDD31-00016A
OEM Part Number
DD31-00016A
Part Type
Dishwasher Drain Pump Motor (BLDC)
Condition
Aftermarket Replacement
Brand
Samsung
Motor Type
Brushless DC (BLDC)
Voltage Compatibility
120V / 230V
Weight
Approx. 0.50 lbs
Package Dimensions
4.02" x 3.50" x 3.54"
Repair Difficulty
Moderate — 30 to 60 minutes
Quantity
1 drain pump motor
Compatible Brand
Samsung
Installation Notes
⚠️ Unplug Dishwasher And Shut Off Water Supply Before Starting — This Step Needs Two Hands Turn off and unplug the dishwasher for safety, and shut off the water supply before beginning. Wear work gloves. Remove any panels or components blocking access to the motor pump. Disconnect all wiring from the old motor. Removing the old motor requires holding a release tab open while simultaneously twisting the motor counterclockwise — this two-handed step trips up a lot of first-time installers, so take it slowly and make sure the tab stays held open through the full twist. Once free, remove the old motor. Install the new DD31-00016A securely in the same mounting position. Reconnect all wiring according to the original connections. Reinstall any panels or components removed for access. Restore the water supply and power, then run a test cycle to confirm the dishwasher drains completely with no leaks or unusual noise. Tools needed: screwdriver, work gloves.
Frequently Asked Questions
My dishwasher isn't draining. Is this the part I need?
Yes, this is the most direct symptom of a failed drain pump motor. Since this motor is what removes water from the tub during the drain phase, a worn or failed motor can leave standing water behind or prevent the cycle from completing properly.
My dishwasher's drainage problem only happens sometimes. Could this still be the motor?
Yes, this is possible. One customer replaced this exact motor to address an intermittent draining issue, noting it was somewhat of a guess since the problem didn't occur every cycle. Intermittent symptoms can still point to a motor that's beginning to fail rather than one that's failed completely, though it's worth noting the customer wasn't fully certain the replacement resolved their specific issue.
What's the trickiest part of installing this motor?
Removing the old motor requires holding a release tab open while twisting the motor counterclockwise at the same time — a two-handed maneuver that one customer specifically called out as the biggest challenge of the whole repair. Taking it slowly and keeping steady pressure on the tab through the full twist makes this easier.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured to match the motor design, impeller mechanism, and voltage compatibility of the original DD31-00016A drain pump motor used in compatible Samsung dishwashers.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
5304532557 Refrigerator Genuine Evaporator Motor
Replaces Part Numbers: 5304532557, 242077707, AP7194947, PS16745551.
Description: This Part is a Genuine OEM refrigerator evaporator fan motor compatible with specific Electrolux, Frigidaire refrigerator models. The fan motor is a vital component of your refrigerator. It is designed to maintain cold temperatures by circulating air through the fresh food compartments. By doing so, it ensures uniform cooling within the refrigerator. This helps to prevent warm spots that can lead to frost build-up.
279827 Genuine OEM Whirlpool Dryer Drive Motor
The 279827 is a Genuine OEM Whirlpool replacement dryer drive motor with pre-attached pulley, compatible with a wide range of Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Estate, and Kenmore dryers. The drive motor is the component that powers everything that moves in your dryer — it turns the drum belt (which rotates the drum to tumble clothes) and simultaneously drives the blower wheel (which pushes heated air through the drum and out the exhaust vent). When the motor fails, the dryer either won't start, won't tumble, stops mid-cycle, or makes loud humming, buzzing, or grinding noises.
This is a dual-shaft motor: the drive shaft (1-3/4" long) connects to the drum belt via the pre-attached pulley, and the blower shaft (1-3/4" long) drives the blower wheel. The pulley is pre-attached and is not available separately — if your old motor's pulley is worn, this replacement includes a new one. As a Genuine OEM part manufactured by Whirlpool to factory specifications, the 279827 is one of the most widely used dryer motors across the Whirlpool platform, replacing over 70 legacy part numbers spanning decades of production. Key cross-references include W10448892, W10396029, W10194250, 8066206, 3395654, 3398046, 3391888, 3395652, AP3094245, PS334304, and EAP334304. Includes the motor assembly, two 1/8" insulated female terminals, and instructions. Before replacing the motor, check the thermal fuse (electric dryers) and door switch first — a blown fuse or failed switch produces identical no-start symptoms and is a far cheaper fix. Installs in 45–90 minutes with basic hand tools.
Quick Answer
The 279827 Genuine OEM Whirlpool Dryer Drive Motor fixes Whirlpool, Maytag, KitchenAid, Amana, Roper, Estate, and Kenmore dryers that won't start, won't tumble, stop mid-cycle, or make loud humming/buzzing/grinding noises. Dual-shaft drive motor with pre-attached pulley. Shaft lengths: blower 1-3/4", drive 1-3/4". Includes motor assembly + 2 insulated female terminals + instructions. Genuine OEM. Key cross-refs: W10448892, W10396029, W10194250, 8066206, 3395654, AP3094245, PS334304. Before replacing the motor: check the thermal fuse and door switch first — they're far cheaper fixes for no-start symptoms.
Common Problems This Part Fixes
Dryer won't start — motor has failed or seized
Dryer won't tumble — motor not powering the drum belt
Dryer stops mid-cycle — motor overheating or intermittently failing
Loud humming or buzzing when the start button is pressed — motor trying to start but can't
Grinding or squealing noise during operation — worn motor bearings
Motor runs but drum doesn't turn — pulley worn or belt slipping on a worn motor shaft
Dryer runs intermittently — motor cutting out from thermal overload
Burning smell from the motor area — overheating windings or seized bearings
Motor locked up or seized — bearings failed completely
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This dryer drive motor directly replaces a large number of OEM and cross-reference part numbers spanning decades of Whirlpool-platform dryer production. Key replacements include:
279827, 3388235, 2019, 2584, 26000299992, 26000695925, 337099, 337100, 3388209, 3388234, 339088, 3391886, 3391887, 3392857, 339627, 339635, 339662, 339672, 340907, 343029, 345437, 348804, 349587, 349808, 3980069, 660199, 660617, 661654, 687499, 687988, 690094, 690870, 694051, 695089, 695925, 697075, 786067, 786090, 8066206, 8066207, 8115, 8528319, 8538262, 8539555, S87-531, W10194250, W10366770, W10396029, W10396032, W10448892, AH334304, AM211, EA334304, K35-099, OEM9282744, AP3094245, AWP39205, EAP334304, PD00002349, PS334304.
This is one of the most extensively cross-referenced parts in the Whirlpool catalog. If your old motor shows a part number not listed here, contact our support team with your dryer model number and we will verify compatibility.
Compatibility
This drive motor is compatible with select dryers from the following brands:
Whirlpool dryers — electric and gas models across many generations (WED, WGD, LER, LGR, LEQ, LGQ series and many more)
Maytag dryers — select Whirlpool-built models (MED, MGD, MEDC, MEDX series)
KitchenAid dryers (select models)
Jenn-Air dryers (select models)
Amana dryers — select models (NED, NGD series)
Magic Chef dryers (select models)
Admiral dryers (select models)
Norge dryers (select models)
Roper dryers (select models)
Estate dryers (select models)
Kenmore / Sears dryers — select Whirlpool-built models (110-series)
Important — Before Replacing the Motor: A dryer that won't start can be caused by several components that are far cheaper and easier to replace than the motor. Before ordering, check the thermal fuse (electric dryers — test for continuity with a multimeter), the door switch (test for continuity when pressed), and the start switch. All three produce identical no-start symptoms. Only replace the motor after ruling out these common causes — a motor replacement is a significant repair, and it's far cheaper to replace a $10 thermal fuse than a $150+ motor. Always verify your dryer model number before ordering.
Key Features
Genuine OEM part manufactured by Whirlpool to factory specifications — guaranteed fit and performance
Dryer drive motor — powers the drum (via belt and pulley) and the blower wheel simultaneously
Dual-shaft design: drive shaft 1-3/4" and blower shaft 1-3/4"
Pre-attached pulley (pulley is not available separately — included with the motor)
Resolves "won't start," "won't tumble," "stops mid-cycle," "humming/buzzing," "grinding," and "burning smell" symptoms when caused by motor failure
Includes motor assembly, two 1/8" insulated female terminals, and instructions
One of the most widely used dryer motors across the Whirlpool platform — replaces 60+ legacy part numbers
Key cross-references: W10448892, W10396029, W10194250, 8066206, 3395654, 3398046, 3391888, AP3094245, PS334304, EAP334304
Compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Estate, and Kenmore dryers
Designed for heavy daily use with minimal noise
DIY repair — installs in 45–90 minutes with basic hand tools
Product Specifications
Part Number
279827
Part Type
Dryer Drive Motor with Pulley
Condition
Genuine OEM
Application
Dryers — Electric & Gas (Whirlpool platform)
Drive Shaft Length
1-3/4"
Blower Shaft Length
1-3/4"
Pulley
Pre-attached (not sold separately)
Function
Powers drum rotation (via belt/pulley) and blower wheel
Kit Includes
Motor assembly, 2x 1/8" insulated female terminals, instructions
Compatible Brands
Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Estate, Kenmore
Installation Notes
⚠️ Disconnect Power Before Starting — 240V Circuit (Electric) or Gas Line (Gas) — Wear Work Gloves Disconnect power at the breaker before beginning — electric dryers operate on a 240V circuit and there is a serious risk of electrical shock. For gas dryers, also shut off the gas supply at the shutoff valve. Wear work gloves and safety glasses. Pull the dryer away from the wall. Remove the lint screen and the screws beneath it. For most Whirlpool-platform dryers, remove the top panel by releasing the spring clips at the front, then detach the front panel by removing the screws at the top corners. Disconnect the door switch wires and set the front panel aside. Support the drum and slide it forward to access the motor at the bottom rear. Remove the drum belt from the motor pulley and idler pulley. Photograph the motor's wiring connections before disconnecting. Disconnect the electrical connections from the motor. Remove the blower wheel from the old motor's blower shaft — this typically requires a clamp or clip removal (the blower wheel threads off counterclockwise on many models). Remove the motor mounting clip/bracket and lift out the old motor. Install the new 279827 motor in the same position. Transfer the blower wheel onto the new motor's blower shaft and secure it. Reinstall the motor mounting clip/bracket. Reconnect the electrical connections using the included insulated female terminals if needed (match your photos). Re-route the drum belt around the drum, through the idler pulley, and onto the motor pulley. Reassemble the front panel, top panel, and lint screen. Restore power (and gas for gas dryers) and run a test cycle — confirm the drum spins smoothly and heated air flows through the drum. Tools needed: Phillips screwdriver, nut driver, socket/ratchet set, putty knife (for spring clips), needle-nose pliers, work gloves, safety glasses.
Frequently Asked Questions
My dryer won't start — is the motor definitely the problem?
Not necessarily — and this is important because a motor replacement is a significant repair. A dryer that won't start can be caused by several components that are far cheaper and easier to replace. Before ordering the motor, check these first: 1) Thermal fuse (electric dryers) — a blown thermal fuse is the single most common cause of a no-start condition. Test for continuity with a multimeter; if it reads open, replace the fuse (~$10). 2) Door switch — test for continuity when pressed; if it's failed, the dryer won't start as a safety measure. 3) Start switch — if pressing the start button produces no response at all, the start switch itself may have failed. Only replace the motor after ruling these out. Signs that point specifically to the motor: a loud humming or buzzing when you press start (motor trying but can't turn), grinding or squealing from the motor area, or a motor that runs intermittently and cuts out.
Why does the motor hum but the drum doesn't turn?
A humming motor that won't turn is a classic sign of a seized or failing motor — the windings are energized (hence the hum) but the shaft can't rotate because the bearings have failed or the motor is mechanically stuck. This can also be caused by the blower wheel being jammed with lint or debris, preventing the shaft from turning — so before condemning the motor, check the blower wheel for obstructions. If the blower wheel spins freely and the motor still hums without turning, the motor has failed and needs replacement. Note: a humming motor that won't start will eventually trip the thermal fuse as a safety measure, so you may need to replace both the motor and the thermal fuse.
Why are there so many cross-reference part numbers for this motor?
The 279827 is one of the most extensively cross-referenced parts in the Whirlpool catalog because it's been the standard dryer drive motor across the Whirlpool platform for decades — spanning Whirlpool, Maytag, KitchenAid, Amana, Roper, Estate, Kenmore, and many other brands that Whirlpool manufactures for. Over the years, the motor has been assigned different part numbers by different brands, distributors, and catalog systems (W10448892, W10396029, 8066206, 3395654, 3398046, etc.), but they all point to the same motor. If your old motor shows ANY of those numbers, the 279827 is the correct replacement.
Does this motor come with the pulley?
Yes — the pulley is pre-attached to the motor and is not available separately. The pulley is what the drum belt rides on, transferring the motor's rotation to the drum. If your old motor's pulley was worn or grooved (a common cause of belt slipping and squealing), the new 279827 includes a fresh pulley. You will need to transfer the blower wheel from your old motor to the new one — the blower wheel is not included.
Should I replace the belt and idler pulley while changing the motor?
It's strongly recommended. When you replace the motor, the dryer is already apart and both the drum belt and idler pulley are right there in your hands. All three components wear from the same friction and heat cycles, and installing a new motor with a worn belt or a seized idler pulley puts unnecessary stress on the new motor from day one. Many technicians replace the belt, idler pulley, and drum support rollers as standard maintenance whenever the dryer is opened for a motor replacement — the combined cost of these parts is modest compared to the labor of disassembling the dryer again later.
Is this a Genuine OEM or aftermarket part?
This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It is the exact same drive motor with pulley installed in compatible Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Estate, and Kenmore dryers from the factory — guaranteed fit, materials, and performance.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
