Search results for "Condenser Fan Motor"

WPW10448896 Dryer Genuine OEM Drive Motor Replaces Part Number: WPW10448896, W10448896, 2312076, 8547170, 8571882, W10007310, W10136931, W10136932, W10396036, W10460374, AP6021554, PS11754878.  Description:  This Dryer Drive Motor is a Genuine OEM part for specific Whirlpool, Kenmore, Maytag dryer models. This motor is responsible for turning the drum and the blower wheel, which allows for effective drying and air circulation within the dryer.  Over time, the drive motor can wear out or fail due to mechanical stress, electrical issues, or general wear from regular use. Causes of a bad drive motor include motor burnout, worn bearings, or issues with the electrical connections.

Read more less

DD94-01031A Dishwasher Duct Condensor Assembly   Replaces Part Numbers: DD94-01031A, 4001433, AP5586892, PS4222729.      California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

Genuine GE OEM Part GE WD24X25325 Dishwasher Genuine Fan Vent Assembly Genuine GE door-vent blower/fan assembly for select GE and Haier dishwashers. Product Overview The GE WD24X25325 Dishwasher Fan Vent Assembly is a genuine OEM replacement used in the dishwasher door ventilation system. The blower circulates air through the door vent during the drying portion of the cycle to help reduce retained moisture and improve drying performance. Quick Answer WD24X25325 is a Genuine GE OEM dishwasher door-vent blower/fan motor assembly. It is used on select GE and Haier dishwashers and helps move moist air through the door vent during drying. Common Problems This Part May Fix Poor drying performance Excess moisture remaining after a cycle Door vent fan does not run Unusual noise from the vent/blower area Moist air is not being exhausted through the door vent Replaces and Cross-References WD24X25325, 265D2664G005, U40G12BS3A5-51, AGE25072, AP6972063, EAP12726435, PD00073154, PS12726435. Cross-reference numbers are supplied for identification. Always verify the complete dishwasher model number before ordering. Compatibility Fits select GE and Haier dishwashers. Compatible model examples include: CDT800P2N0S1 CDT805P2N0S1 CDT845P2N3S1 DDT700SBN0TS GDF645SSN0SS GDT645SFN3DS GDT665SFN0DS GDP665SYN3FS PDT715SYN2FS PDT715SFN0DS PDP715SYN3FS QDP555SYN0FS Important: This is only a partial compatibility list. Confirm the exact dishwasher model number before purchase because similar models may use a different vent or blower assembly. Key Features Genuine GE Appliances OEM part Complete door-vent blower/fan assembly Circulates air through the dishwasher door vent Helps reduce moisture during drying For select GE and Haier dishwashers Product Specifications Manufacturer GE Appliances Manufacturer Part Number WD24X25325 Part Type Dishwasher Fan Vent / Door Vent Blower Assembly Condition New Part Quality Genuine OEM Application Dishwasher Door Ventilation / Drying System Approx. Shipping Weight 0.5 lb Installation Notes Disconnect electrical power to the dishwasher at the breaker before service. Access the door vent assembly according to the appliance service procedure. Disconnect the wiring connector carefully before removing the old fan assembly. Transfer or reuse any hardware only as directed for the specific model. Confirm the vent path is clear and the new assembly is fully seated before reassembly. Diagnostic note: Poor drying can also result from rinse-aid settings, heating-system faults, blocked vent passages, or control issues. Confirm the fan assembly is defective before replacing it. Frequently Asked Questions Is WD24X25325 a Genuine GE OEM part? Yes. GE Appliances identifies WD24X25325 as a genuine replacement fan vent assembly. What does this fan assembly do? It circulates air through the dishwasher door vent to help reduce moisture during the drying stage. Does it fit every GE dishwasher? No. It fits specific GE and Haier models. Verify the complete model number before ordering. Is this only the fan motor? This listing is for the complete WD24X25325 fan vent / door-vent blower assembly as supplied by GE. Shop With Confidence Use your dishwasher's complete model number to confirm fitment before purchase. Genuine GE OEMFan Vent AssemblyModel Verification RecommendedFast U.S. Shipping

Read more less

5901JA1021A Genuine OEM LG Refrigerator Evaporator Fan Blade The 5901JA1021A is a genuine LG OEM evaporator fan blade for LG and select Kenmore refrigerators. This is the plastic blade itself — not the motor — that mounts onto the evaporator fan motor's shaft and physically moves air through the evaporator fins and interior compartment as it spins, which is what carries cooled air to the fresh food and freezer sections and helps maintain efficient, even cooling. Over time, the blade can crack, chip, or warp from ice contact, age, or physical damage, even while the motor underneath it is still working perfectly fine. A damaged fan blade typically shows up as reduced airflow and less effective cooling, a wobbling or unbalanced sound as the fan spins, or visible cracks and missing pieces on the blade itself. Since this is the blade only, it's a straightforward and inexpensive fix when the motor is still good but the blade has failed. It directly replaces 5901JJ1005A, AP4457221, 1268187, AH3528674, EA3528674, and PS3528674. Quick Answer The 5901JA1021A Genuine OEM LG Refrigerator Evaporator Fan Blade fixes LG and select Kenmore refrigerators with reduced cooling airflow, a wobbling or unbalanced fan noise, or a cracked/chipped/missing fan blade. Replaces 5901JJ1005A, AP4457221, 1268187, AH3528674, EA3528674, PS3528674. This is the blade only, not the motor — if your fan motor itself has failed (won't spin, no power, electrical fault), you need a motor replacement instead, such as our EAU61524007 listing. Common Problems This Part Fixes Reduced airflow and less effective cooling despite the fan motor running Wobbling, unbalanced, or rattling sound as the fan spins Visible cracks, chips, or missing sections on the fan blade Fan blade that has broken away from the motor shaft Inconsistent cooling performance in the refrigerator or freezer Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This refrigerator evaporator fan blade directly replaces the following OEM and cross-reference part numbers: 5901JA1021A, 5901JJ1005A, 1268187, ADP73694301, ALG51767, AP4457221, EAP3528674, PD00009011 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This evaporator fan blade is compatible with select LG refrigerators, and also fits select Kenmore refrigerators built on the LG platform, including model numbers such as 71052, 71053, 71059, 71073, 71602, 71603, and 71609. Note — blade only, not the motor: This listing is for the fan blade component only. If your evaporator fan motor itself has failed electrically (won't spin at all, no power, humming with no rotation), you need a full motor replacement instead of just this blade. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which part your refrigerator needs. Key Features Genuine LG OEM part — factory-specified blade design and shaft fit Mounts directly onto the existing evaporator fan motor shaft Resolves "reduced airflow," "wobbling fan noise," and "cracked or chipped blade" symptoms Inexpensive fix when only the blade — not the motor — has failed Durable plastic construction designed for the freezer environment Direct drop-in replacement — no tools required on most models Replaces 5901JJ1005A, AP4457221, 1268187, AH3528674, EA3528674, and PS3528674 Compatible with LG and select Kenmore refrigerators Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number 5901JA1021A Part Type Refrigerator Evaporator Fan Blade (Blade Only) Condition Genuine OEM Brand LG Material Plastic Function Moves air through the evaporator fins and compartment when mounted to the fan motor shaft Includes Motor No — blade only Repair Difficulty Very Easy — typically no tools required Quantity 1 fan blade Compatible Brands LG, Kenmore Installation Notes ⚠️ Unplug Refrigerator Before Starting Disconnect power at the outlet before beginning, and move perishable food to a cooler for the duration of the repair. Wear work gloves. Access is typically through the freezer's rear interior panel: remove shelving and bins as needed, then remove the screws securing the back panel to expose the evaporator fan. If there's significant frost or ice around the fan or coil, let the unit sit unplugged with the door open for a few hours, or run a manual defrost, before continuing. Photograph the old blade's orientation on the motor shaft before removing it. Gently pull the old fan blade off the motor shaft — it typically presses on and off without tools. Press the new 5901JA1021A blade onto the same motor shaft in the same orientation, seating it fully. Confirm the blade spins freely by hand without wobbling or contacting the housing before reassembling the back panel. Restore power and monitor cooling performance over the next 24 hours to confirm normal, even airflow has returned. Tools needed: Phillips screwdriver (for the rear panel), work gloves. Frequently Asked Questions How do I know if I need just the blade or the whole motor? Check whether the motor is actually turning. If you can see or hear the motor shaft spinning but the blade is cracked, wobbling, or missing pieces, this blade-only replacement is the correct and less expensive fix. If the motor itself isn't turning at all — no spin, no hum, or an electrical fault — the motor has failed and needs to be replaced instead, which is a different part from this blade. My fan makes a wobbling or rattling noise. Is that the blade? It's a strong possibility, especially if the motor itself sounds otherwise normal. A cracked, chipped, or unevenly worn blade can throw off the fan's balance as it spins, producing a rattling or wobbling sound distinct from the grinding noise typically associated with a failing motor bearing. Do I need any tools to replace this blade? No, in most cases. The blade presses onto and off of the motor shaft without tools — you'll just need a screwdriver to access the rear panel covering the evaporator fan area, but the blade swap itself is tool-free. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by LG to factory specifications — guaranteed fit, materials, and performance. It matches the original blade design and motor shaft fit of the evaporator fan blade originally installed in your refrigerator. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO DD31-00005A Dishwasher Drain Pump Motor The XPARTCO DD31-00005A is an aftermarket replacement drain pump motor for Samsung dishwashers. This pump uses an internal impeller to force wastewater out of the tub and through the drain hose during the drain phase of the wash cycle — it's the component doing the physical work every time your dishwasher empties itself between cycle stages and at the end of the wash. Rated 120V, 0.8A. Over time, the impeller can wear down, debris can jam the motor, or the motor windings themselves can fail electrically. A failing drain pump produces a very recognizable pattern: standing water left in the tub after a cycle finishes, water leaking from underneath the dishwasher, unusually loud or grinding noise during the drain phase, or a pump that audibly tries to run for a moment and then shuts off right away without actually clearing the water. It directly replaces AP4342621 and PS4222308. Quick Answer The XPARTCO DD31-00005A Dishwasher Drain Pump Motor fixes Samsung dishwashers that won't drain, leave standing water in the tub, leak underneath the unit, or run unusually noisy during the drain phase. 120V, 0.8A. Replaces AP4342621, PS4222308. This is the drain pump — not the same part as the wash/circulation pump (DD31-00004B), which handles spraying water during the wash itself rather than draining it afterward. Common Problems This Part Fixes Dishwasher not draining — standing water left in the tub after a cycle Water leaking from underneath the dishwasher Unusually loud, grinding, or strange noise during the drain phase Pump that tries to run briefly, then shuts off right away without draining Dishwasher running noisily overall Cycle that stalls or won't advance past the drain step Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dishwasher drain pump motor directly replaces the following OEM and cross-reference part numbers: DD31-00005A, 1550731, DW0005A, AP4342621, ASM35435 PD00002014, PS4222308 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drain pump motor is compatible with select Samsung dishwashers, including model numbers such as: DMR57LFB, DMR57LFS, DMR57LFW DMR77LHB, DMR77LHS, DMR77LHW DMR78AHB, DMR78AHS, DMR78AHW DMT300RFB, DMT300RFS, DMT300RFW DMT400RHB, DMT400RHS, DMT400RHW DMT800RHB, DMT800RHS, DMT800RHW Note — drain pump, not wash pump: This is the drain pump, which removes wastewater from the tub. It is a different part from the DD31-00004B wash/circulation pump motor, which sprays water through the spray arms during the wash itself. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which pump your dishwasher needs. Key Features Aftermarket replacement drain pump motor — removes wastewater from the tub during the drain phase Resolves "not draining," "standing water," "leaking underneath," and "noisy drain phase" symptoms caused by pump failure Impeller-driven design for efficient water removal through the drain hose Rated 120V, 0.8A Direct drop-in replacement — matches the original mounting and hose connections Replaces AP4342621 and PS4222308 Compatible with a range of Samsung dishwasher models Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number DD31-00005A OEM Part Number DD31-00005A Part Type Dishwasher Drain Pump Motor Condition Aftermarket Replacement Brand Samsung Function Removes wastewater from the tub during the drain phase Voltage 120V Amperage 0.8 A Related Part DD31-00004B wash/circulation pump (different function, sold separately) Repair Difficulty Moderate — tight working space under the unit Quantity 1 drain pump motor Compatible Brand Samsung Installation Notes ⚠️ Unplug Dishwasher And Shut Off Water Supply Before Starting — Remove Standing Water First Unplug the dishwasher and shut off the water supply before beginning. Wear work gloves. If there's standing water left in the tub from the original failure, remove as much as possible by hand with a cup or towel before starting the repair. Access to the drain pump is typically from underneath the unit, which can mean a tight working space — pulling the dishwasher partially out from under the counter, or working from the front after removing the lower access panel, makes this considerably easier depending on your installation. Photograph the wiring and hose connections before disconnecting anything. Disconnect the electrical connector and the drain hose connections from the old pump, remove its mounting screws or clips, and pull it free. Install the new DD31-00005A pump in the same position, reconnect the drain hose connections securely, and reconnect the electrical connector fully. Restore the water supply and power, then run a cycle and check underneath for leaks while confirming the tub drains completely at the end. Tools needed: Phillips screwdriver, pliers, towels or a small cup for removing standing water, work gloves. Frequently Asked Questions My dishwasher pump tries to run for a second, then shuts off. Is that the drain pump? Yes, this is a documented symptom of a failing drain pump motor — one customer described exactly this pattern, where the pump attempted to run and then shut off right away without actually clearing the standing water. This typically points to a motor that's jammed, worn, or electrically failing rather than a clog, since a simple clog usually lets the motor keep running (just ineffectively) rather than shutting off immediately. Access to my drain pump is really tight. Is that normal? Yes, this is a common challenge with under-counter dishwasher installations — the drain pump often sits low and toward the back, and reaching it can mean working in a cramped space regardless of the model. Removing standing water first and having patience with the process makes a real difference, and pulling the unit partially forward, if your installation allows it, can improve access significantly. Is this the same as the wash pump on my dishwasher? No. This DD31-00005A is specifically the drain pump, which removes wastewater from the tub. Your dishwasher's separate wash/circulation pump (DD31-00004B) is what sprays water through the spray arms during the actual wash portion of the cycle. If your dishwasher isn't cleaning dishes well but drains fine, the wash pump — not this drain pump — is more likely the issue. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured to match the electrical rating, impeller design, and mounting configuration of the original DD31-00005A drain pump motor used in compatible Samsung dishwashers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WPW10348269 Genuine OEM Whirlpool Dishwasher Drain Pump Motor The WPW10348269 is a genuine Whirlpool OEM drain pump motor for Whirlpool, KitchenAid, Kenmore, Maytag, Amana, Crosley, Estate, Inglis, Jenn-Air, Magic Chef, and Roper dishwashers. This pump uses an electric motor to create suction, pulling wastewater out of the tub and expelling it through the drain hose at the end of each cycle. This is the dedicated drain pump, distinct from a circulation pump — such as our WPW10605057 listing — which handles spraying water through the spray arms during the wash itself rather than draining it afterward. Rated 120VAC, 60Hz, 45W, 0.7A, with a run time pattern of 5 minutes on, 30 minutes off. Ships as a complete pump motor with impeller and O-ring. If the impeller becomes damaged or the motor shorts out and stops draining, the pump body itself can crack over time, leading to leakage — replacing the pump before that happens is the more reliable fix. Symptoms of a failing drain pump include water not draining from the tub, unusual noise such as grinding during the drain phase, or visible leaks from underneath the unit. It directly replaces W10348269, W10084573, 661662, 8558995, 8565839, W10158351, WPW10348269VP, AP6020066, AWP49992, PD00004898, PS11753379 Quick Answer The WPW10348269 Genuine OEM Whirlpool Dishwasher Drain Pump Motor fixes Whirlpool, KitchenAid, Kenmore, Maytag, Amana, Crosley, Estate, Inglis, Jenn-Air, Magic Chef, and Roper dishwashers that aren't draining, are making grinding noise during the drain phase, or are leaking from underneath. 120VAC, 60Hz, 45W, 0.7A. Includes impeller and O-ring. Replaces W10348269, WPW10348269VP, W10084573, W10158351, 661662, 8558995, 8565839, 2813258, AP6020066, EAP11753379, PD00004898, PS11753379. This is the drain pump — a separate part from our WPW10605057 circulation pump listing, which handles spraying water rather than draining it. Common Problems This Part Fixes Dishwasher not draining — standing water left in the tub after a cycle Grinding noise coming from the drain pump area Water leaking from underneath the dishwasher Cycle stalling or failing to advance past the drain step Dishes not getting cleaned as a downstream effect of drainage problems Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dishwasher drain pump motor directly replaces the following OEM and cross-reference part numbers: WPW10348269, W10348269, W10084573, 661662, 8558995, 8565839, W10158351, WPW10348269VP, AP6020066, AWP49992, PD00004898, PS11753379 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drain pump motor is compatible with select Whirlpool dishwashers, and also fits select KitchenAid, Kenmore, Maytag, Amana, Crosley, Estate, Inglis, Jenn-Air, Magic Chef, and Roper dishwashers built on the Whirlpool platform. Note — drain pump, not circulation pump: This is the dedicated drain pump, which removes wastewater from the tub. It is a separate part from our WPW10605057 listing, which is the circulation pump and diverter motor responsible for spraying water through the spray arms during the wash itself. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which pump your dishwasher needs. Key Features Genuine Whirlpool OEM part — factory-specified motor and impeller design Pumps wastewater out of the tub through the drain hose Resolves "not draining," "grinding noise," and "leaking underneath" symptoms caused by pump failure Complete assembly — includes pump motor, impeller, and O-ring Rated 120VAC, 60Hz, 45W, 0.7A Run time: 5 minutes on, 30 minutes off Dimensions: approximately 3-1/2"L x 3"W x 3-1/2"H Direct drop-in replacement — matches the original mounting and hose connections Replaces W10348269, W10084573, 661662, 8558995, 8565839, W10158351, WPW10348269VP, AP6020066, AWP49992, PD00004898, PS11753379 Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number WPW10348269 Part Type Dishwasher Drain Pump Motor (with Impeller and O-Ring) Condition Genuine OEM Brand Whirlpool Function Pumps wastewater out of the tub through the drain hose Voltage 120VAC Frequency 60 Hz Wattage 45 W Amperage 0.7 A Run Time 5 min ON / 30 min OFF Dimensions Approx. 3-1/2"L x 3"W x 3-1/2"H Color White / Gray / Black / Yellow Related Part WPW10605057 circulation pump & diverter motor (different function, sold separately) Repair Difficulty Beginner to Moderate Quantity 1 drain pump motor Compatible Brands Whirlpool, KitchenAid, Kenmore, Maytag, Amana, Crosley, Estate, Inglis, Jenn-Air, Magic Chef, Roper Installation Notes ⚠️ Unplug Dishwasher Before Starting — Removing The Unit Makes Access Easier Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. This repair can be done without pulling the dishwasher out from under the counter, but many technicians find it considerably easier to access the pump if you do pull the unit out first. Remove the lower rack and any components blocking access to the tub floor, then work from underneath the dishwasher to reach the drain pump. Test the old pump for continuity with a multimeter before removing it — if it shows no continuity, or if it's getting power but still won't run, that confirms the pump has failed. Photograph the wiring and hose connections before disconnecting anything. Disconnect the electrical connector and the drain hose connection from the old pump, remove its mounting hardware, and pull it free. Install the new WPW10348269 in the same position, reconnect the drain hose connection securely, and reconnect the electrical connector fully. Reinstall any components removed for access and the lower rack. Restore power, run a test cycle, and check underneath for leaks while confirming the tub drains completely at the end. Tools needed: Phillips screwdriver, 5/16" nut driver, 5/8" wrench, flathead screwdriver, multimeter, work gloves. Frequently Asked Questions Do I need to pull the dishwasher out from under the counter for this repair? Not strictly — this pump can be replaced without fully removing the dishwasher. That said, several customers who've done this repair note that pulling the unit out first makes access considerably easier, since you're working from underneath the appliance either way. If you have the space to pull it out, it's worth doing to make the job smoother. How do I know if the pump has actually failed? Test the pump motor with a multimeter set to continuity before replacing it. If there's no continuity, or if the pump is receiving power but still won't run, that confirms the motor has failed and the pump should be replaced. This quick check avoids replacing a part that isn't actually the problem. My old pump was leaking. Why does that happen? If the impeller becomes damaged or the motor shorts out and stops running, the pump body itself can develop a crack over time, which leads to leakage. Rather than trying to repair a leaking pump, replacing the complete assembly resolves both the drainage failure and the leak at the same time. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original motor, impeller, and hose connection configuration of the drain pump originally installed in your dishwasher. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

W11497943 Dishwasher Genuine Drain Pump Motor Replaces Part Numbers: W11497943, AP6994646, PS16221213, W11412663.   Description: This Drain Pump Motor is a Genuine OEM component for select Maytag, Kenmore, Whirlpool dishwasher models. This electric motor powers the drain pump to empty wash water from the tub at the end of cycles. Common causes of a bad pump motor include wear over extended use, moisture damage degrading electronics, or electrical faults from voltage fluctuations.

Read more less

CON-5-370-R HVAC ROUND MOTOR RUN CAPACITOR Appli Parts Run Capacitor for ac 5 Mfd uF (microfarads) 370 VAC Appli Parts Run Capacitor for ac 5 Mfd uF (microfarads) 370 VAC Round Universal fit for hvac and other applications 2-1/2 in High 1-1/2 in Wide CON-5-370Universal: Replaces any brand with the same capacitance capacity and voltage. Will work for 370V . 1/4 in Male Quick-connectSpecs: Tolerance is +/- 5 % of Capacity, Working temperature environment from -40F (-40C) to +185F (85C). Dimensions 2-5/8 in H, 1-1/2 in WProtection: Protected for 10,000AFC which means this product will not burst if by any reason is short circuitsReplaces: TRCF5 PRCF5A CAP-5-370Confirm that the dimensions and other attributes of the product closely match those of the original item being replaced

Read more less

W11236851 Refrigerator Genuine OEM Air Damper Diffuser The W11236851 is a genuine Whirlpool OEM air damper diffuser assembly for Whirlpool refrigerators, and also fits select Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore, and Ikea models. Located inside the refrigerator behind the evaporator cover, this damper controls the flow of cold air from the freezer into the refrigerator compartment, opening and closing as needed to maintain the set temperatures in each section. Causes of a bad damper include wear and tear of the movable parts over time, failure of the actuator motor that powers it, or damage from something accidentally blocking the damper mechanism. Symptoms of a failing damper include the refrigerator section running too cold or too warm, the freezer section running too cool or too warm, difficulty maintaining set temperatures, excessive condensation inside the appliance, or ice accumulation. It directly replaces 4814117, W11175955, AP6783936, EAP12584010, AWP43935, PD00058357, PS12584010. Quick Answer The W11236851 Refrigerator Genuine OEM Air Damper Diffuser fixes Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore, and Ikea refrigerators where the fridge or freezer section runs too warm or too cold, temperatures are hard to maintain, or you notice excessive condensation or ice buildup. Replaces 4814117, W11175955, AP6783936, EAP12584010, AWP43935, PD00058357, PS12584010. Check that nothing is accidentally blocking the damper mechanism before assuming it has failed — food items or packaging pushed against it can cause the same symptoms as a worn or broken damper. Common Problems This Part Fixes Refrigerator section too cold Refrigerator section too warm Freezer section too cool Freezer section too warm Excessive condensation inside the appliance Ice accumulation Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This refrigerator air damper diffuser directly replaces the following OEM and cross-reference part numbers: W11236851, 4814117, W11175955, AP6783936, EAP12584010, AWP43935, PD00058357, PS12584010 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This air damper diffuser is compatible with select Whirlpool refrigerators, and also fits select Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore, and Ikea refrigerators built on the Whirlpool platform. Note: Always verify your full model number before ordering, since Whirlpool uses several different damper designs across its refrigerator lineup. Contact our support team with your model number if you're unsure. Key Features Genuine Whirlpool OEM part — factory-specified damper and actuator design Controls cold airflow from the freezer into the refrigerator compartment Resolves "too cold," "too warm," "excessive condensation," and "ice accumulation" symptoms Located behind the evaporator cover Direct drop-in replacement matching the original mounting and connections Replaces 4814117, W11175955, AP6783936, EAP12584010, AWP43935, PD00058357, PS12584010 Compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore, and Ikea refrigerators Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number W11236851 Part Type Refrigerator Air Damper Diffuser Assembly Condition Genuine OEM Brand Whirlpool Location Behind the evaporator cover Function Controls cold airflow between the freezer and refrigerator compartments Repair Difficulty Moderate Quantity 1 damper assembly Compatible Brands Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Kenmore, Ikea Installation Notes ⚠️ Unplug Refrigerator Before Starting — Check For Blockages First Unplug the refrigerator and safely store any food that could spoil while the power is off. Wear work gloves. Before disassembling anything, check whether food items or packaging have been accidentally pushed against the damper mechanism, since this can cause the same temperature symptoms as a genuinely failed part. Locate the evaporator cover, typically in the freezer or at the back of the fresh food compartment depending on your model, and remove it to access the damper assembly. Photograph the wiring connection to the actuator motor before disconnecting anything. Disconnect the wiring harness from the old damper assembly, remove any mounting clips or fasteners, and pull it free. Install the new W11236851 in the same position, reconnect the wiring harness fully, and secure any mounting hardware. Reinstall the evaporator cover. Restore power and monitor both the refrigerator and freezer temperatures over the next 24 hours to confirm consistent, accurate cooling in both compartments. Tools needed: Phillips screwdriver (model-dependent), work gloves. Frequently Asked Questions My refrigerator section is too warm but the freezer is fine. Is this the part I need? Yes, this is a common symptom of a failing air damper. Since this damper controls how much cold air moves from the freezer into the refrigerator compartment, a stuck or broken damper can leave the refrigerator section too warm even while the freezer maintains a normal temperature. My freezer or fridge is too cold instead of too warm. Could this still be the damper? Yes. A damper stuck in the open position can let too much cold air flow into the refrigerator compartment, making it colder than intended, while a damper stuck closed can have the opposite effect. Both too-cold and too-warm symptoms in either compartment can point to this same part. What should I check before assuming the damper itself is broken? Check that nothing — food packaging, containers, or shifted items — is physically blocking the damper mechanism, since accidental blocking can produce the same temperature symptoms as a genuinely worn or failed damper, without requiring a replacement part at all. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original damper and actuator design of the air damper diffuser originally installed in your refrigerator. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO W10350564 Refrigerator Run Capacitor Replaces WPW10350564 The XPARTCO W10350564 is an aftermarket replacement compressor run capacitor compatible with a wide range of Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Roper, Admiral, Ikea, and Kenmore refrigerators and freezers. The run capacitor is a small but critical electrical component mounted near the compressor at the back of the refrigerator — it delivers a phase-shifted power boost that helps the compressor motor start at the beginning of each cooling cycle, and supports smooth, efficient motor operation while the compressor runs. When the capacitor fails — typically from dielectric breakdown, age, heat, or moisture intrusion — the compressor may fail to start, hum without starting, kick on and off repeatedly, or cause inconsistent cooling throughout the refrigerator. Rated 12 µF (MFD) ±5% capacitance, 180VAC, 50/60Hz. This capacitor works together with the compressor start relay/start device — the two components are frequently replaced together, since a failed capacitor often stresses the relay and vice versa. It directly replaces WPW10350564, W10350564, AP6020176, PS11753490, EAP11753490, and 2683570. This is one of the most cost-effective refrigerator repairs — a failed run capacitor mimics symptoms of a failed compressor (a far more expensive repair), so testing and replacing the capacitor first can save hundreds of dollars. Installs in about 15 minutes with basic hand tools. Quick Answer The XPARTCO W10350564 Refrigerator Run Capacitor fixes Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, and Kenmore refrigerators and freezers where the compressor won't start, hums without starting, kicks on and off, or the fridge/freezer is too warm with inconsistent cooling. 12 µF (MFD) ±5%, 180VAC, 50/60Hz. Replaces WPW10350564, AP6020176, PS11753490, EAP11753490, 2683570. Often replaced together with the compressor start relay. A 15-minute repair that can save you from misdiagnosing a "failed compressor." Common Problems This Part Fixes Compressor won't start — no power boost from the failed capacitor Compressor hums or clicks but doesn't start running Compressor kicks on and off repeatedly (short cycling) Refrigerator and freezer too warm — cooling cycles not completing Fridge too warm while freezer seems okay — weak compressor operation Noticeable humming sounds from the back of the refrigerator Inconsistent cooling and variable temperatures inside the refrigerator Refrigerator will not start at all Capacitor visibly bulged, leaking, or burned Capacitance test reads significantly off from 12 µF Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This run capacitor directly replaces the following OEM and cross-reference part numbers: WPW10350564, W10350564, PD00030179, EAP11753490, AP6020176, AWP50050, PS11753490. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This run capacitor is compatible with select refrigerators and freezers from the following brands: Whirlpool refrigerators — French door, side-by-side, and bottom-mount models (including WRX735SDBM00 and related WRX/WRF series) Maytag refrigerators (select models) KitchenAid refrigerators (select models) Jenn-Air refrigerators (select models) Amana refrigerators (select models) Magic Chef refrigerators (select models) Roper refrigerators (select models) Admiral refrigerators (select models) Ikea refrigerators (select Whirlpool-built models) Kenmore / Sears refrigerators (select Whirlpool-built models) Also fits compatible upright and chest freezers on the Whirlpool platform Note: The run capacitor works together with the compressor start relay/start device. When one fails, the other has typically been stressed by the same electrical events — many repair scenarios call for replacing both at the same time since both are accessible in the same location and the combined parts cost is still far below a service call. Always verify your model number before ordering. Key Features Compressor run capacitor — delivers the phase-shifted power boost that starts the compressor motor and supports smooth operation during cooling cycles Rated 12 µF (MFD) capacitance with ±5% tolerance — precise match to OEM electrical specifications 180VAC, 50/60Hz rating for compatible refrigerator compressor circuits Resolves "compressor won't start," "humming but not starting," "short cycling," and "too warm" symptoms when caused by capacitor failure A cost-effective first repair — failed capacitors commonly mimic the symptoms of a far more expensive failed compressor Replaces WPW10350564, AP6020176, PS11753490, EAP11753490, and 2683570 Compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Roper, Admiral, Ikea, and Kenmore refrigerators and freezers Often replaced together with the compressor start relay/start device as a paired repair Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in about 15 minutes with basic hand tools Product Specifications Part Number W10350564 OEM Part Number WPW10350564 Part Type Refrigerator Compressor Run Capacitor Condition Aftermarket Replacement Application Refrigerators and Freezers (Whirlpool platform) Capacitance 12 µF (MFD) Tolerance ±5% Voltage 180V AC Frequency 50/60 Hz Mounting Location Near compressor, rear of refrigerator Often Paired With Compressor Start Relay / Start Device Compatible Brands Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Roper, Admiral, Ikea, Kenmore Installation Notes ⚠️ Capacitor Safety Warning — Stored Electrical Charge Capacitors store an electrical charge even after the refrigerator is unplugged. Before handling the old capacitor, discharge it safely: with the refrigerator unplugged, touch the blade of an insulated-handle screwdriver across both capacitor terminals simultaneously to short them together (you may see or hear a small spark — that's the stored charge dissipating). Never touch the capacitor terminals with bare hands before discharging. If you're not comfortable with this step, have the repair done by a qualified appliance technician. ⚠️ Unplug Refrigerator Before Starting — Wear Work Gloves Unplug the refrigerator and pull it away from the wall to access the rear. Safely store any food that could spoil if the repair takes longer than expected. Wear work gloves to protect your hands. The run capacitor is located near the compressor at the bottom rear of the refrigerator, typically behind a lower rear access panel. Remove the screws holding the access panel and set it aside. Locate the capacitor — a small rectangular or oval component connected to the compressor's start relay/start device by wire terminals. Photograph the wire connections before disconnecting anything. Discharge the old capacitor before touching the terminals (see the safety warning above). Disconnect the wire terminals from the old capacitor — note which wire goes to which terminal. Release the capacitor from its mounting clip or bracket. Install the new W10350564 capacitor in the same position, secure the mounting clip, and reconnect the wires to the same terminals as photographed. While the panel is open, inspect the start relay/start device on the side of the compressor — if it rattles when shaken, shows burn marks, or has corroded terminals, replace it at the same time. Reinstall the rear access panel, push the refrigerator back into place, plug it in, and listen for the compressor to start smoothly within a few minutes. Allow several hours for the refrigerator to return to its set temperature. Tools needed: Phillips screwdriver, 1/4" nut driver, insulated-handle flathead screwdriver (for discharging), needle-nose pliers, work gloves. Frequently Asked Questions How do I know if the run capacitor has failed and not the compressor? This is the key question — because a failed $15–30 capacitor produces nearly identical symptoms to a failed $300+ compressor. Signs pointing to the capacitor: the compressor hums or clicks but won't start; the compressor tries to start, runs briefly, then shuts off (short cycling); or the refrigerator gradually stopped cooling with humming from the rear. To test: unplug the refrigerator, discharge the capacitor, disconnect it, and measure it with a multimeter that has a capacitance setting — a healthy capacitor reads close to 12 µF (within ±5%). A reading far off, zero, or infinite confirms the capacitor has failed. Visual signs like bulging, leaking, or burn marks also confirm failure. Given the low cost, replacing the capacitor (and start relay) first is the standard diagnostic approach before condemning the compressor. Should I replace the start relay at the same time? Yes, it's strongly recommended. The run capacitor and the compressor start relay/start device work together in the compressor's starting circuit — the relay switches power to the start winding while the capacitor provides the phase-shifted boost. When one fails, the other has typically been stressed by the same electrical events (voltage spikes, overheating, repeated failed start attempts). Both components are inexpensive, mounted in the same location on or near the compressor, and accessible in the same repair session. A quick relay check: with the refrigerator unplugged, remove the relay and shake it — if it rattles, the internal components have failed and it needs replacement. Why does the capacitor need to be discharged before handling? Capacitors store electrical energy — that's their job. Even after the refrigerator is unplugged, the capacitor can hold a charge capable of delivering a painful (and potentially dangerous) shock when you touch both terminals. Before handling, always discharge the capacitor by shorting both terminals together with the blade of an insulated-handle screwdriver — touch the metal blade across both terminals at once and hold for a second or two. You may see a small spark as the charge dissipates; that's normal. After discharging, the capacitor is safe to handle. This takes five seconds and eliminates the shock risk entirely. What's the difference between a run capacitor and a start capacitor? Both assist the compressor motor but in different phases of operation. A start capacitor delivers a large, brief boost only during the initial moment of motor startup, then is switched out of the circuit. A run capacitor — like the W10350564 — stays in the circuit continuously while the motor runs, providing an ongoing phase shift that improves the motor's running efficiency and torque. Household refrigerators on the Whirlpool platform typically use a run capacitor working alongside the start relay/start device. Match the replacement to your original: the W10350564 is a 12 µF, 180VAC run capacitor, and the capacitance rating must match for correct compressor operation. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the electrical specifications (12 µF ±5%, 180VAC, 50/60Hz), terminal configuration, and compressor-support function of the original WPW10350564/W10350564 run capacitor used in compatible Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, and Kenmore refrigerators and freezers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 6501KW2001B Washer Rotor Positioning Sensor The XPARTCO 6501KW2001B is an aftermarket replacement rotor position sensor (RPS) compatible with a wide range of LG and Kenmore direct-drive front-load washers. This 5-pin Hall effect sensor mounts to the motor stator and monitors the speed and rotational direction of the motor rotor, feeding that data back to the control board so it can properly manage spin speed, direction changes during wash/rinse agitation, and load balancing. When this sensor fails or reads inaccurately, the control board loses the feedback it needs to run the motor correctly, and the washer commonly throws an "LE" (motor/rotor position) error code, fails to spin or agitate, or runs unusually long cycles as it struggles to detect motor movement. Built with PBT-GF30 housing and black epoxy potting for durability in the motor compartment. It directly replaces 6501KW2001A, 6501KW2001D, AP5973402, PS11706506, EAP11706506, and 3282954. Installs in 30–60 minutes with basic hand tools. Quick Answer The XPARTCO 6501KW2001B Washer Rotor Positioning Sensor fixes LG and Kenmore (LG-built) direct-drive front-load washers throwing an "LE" error code, failing to spin or agitate, or running abnormally long cycles. 5-pin Hall effect sensor, PBT-GF30 housing, black epoxy potting. Replaces 6501KW2001A, 6501KW2001D, AP5973402, PS11706506, EAP11706506, 3282954. Classic symptom: washer displays "LE" and stops mid-cycle, or won't spin at all. Common Problems This Part Fixes Washer displays an "LE" (motor/rotor position) error code Tub fails to spin or agitate during the wash cycle Washer struggles to detect load movement, resulting in abnormally long cycle times Motor runs erratically or stalls mid-cycle Washer stops partway through a cycle without completing Inconsistent or failed direction changes during agitation Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This rotor position sensor directly replaces the following OEM and cross-reference part numbers: 6501KW2001B, 6501KW2001A, 6501KW2001D, PD00001726, EAP2497738, 6501KW2001C, EBR37560301, ALG52243, AP4457567, AP5973402, EAP11706506, 3282954, PD00059513, PS3529185, PS11706506 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This rotor position sensor is compatible with select LG-built direct-drive front-load washers, including: LG front-load washers (including WM1814CW, WM2010CW, WM2016CW, WM3455HW) Kenmore front-load washers (select LG-built models, including WD-3243RHD, WD-3245RHD, WD-3274RHD) Important: Do not confuse this with 6501KW2002B, which is a different, non-interchangeable rotor position sensor used on other LG washer platforms. Some newer LG models also integrate the Hall sensor directly into the motor stator assembly (such as AJB73816004) rather than using a standalone sensor like this one. Always verify your appliance model number before ordering, and check your parts diagram to confirm whether your model uses a standalone sensor. Contact our support team with your model number if you're unsure. Key Features Direct-fit replacement LG/Kenmore washer rotor position sensor (Hall effect, 5-pin) Resolves "LE error code," "won't spin," "won't agitate," and "long cycle time" symptoms Monitors motor rotor speed and rotational direction for accurate control board feedback PBT-GF30 housing with black epoxy potting for durability in the motor compartment Replaces 6501KW2001A, 6501KW2001D, AP5973402, PS11706506, EAP11706506, and 3282954 Compatible with select LG and Kenmore (LG-built) direct-drive front-load washers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number XP6501KW2001B OEM Part Number 6501KW2001B Part Type Washer Motor Rotor Position Sensor Condition Aftermarket Replacement Sensor Type Hall Effect, 5-Pin Housing Material PBT-GF30 with black epoxy potting Application LG-Built Direct-Drive Front-Load Washer Motor Assembly Compatible Brands LG, Kenmore Installation Notes ⚠️ Unplug Washer Before Starting Disconnect power before beginning. Access the motor compartment, typically by removing the rear panel of the washer. Locate the rotor position sensor mounted to the motor stator near the rotor. Photograph the wiring before disconnecting, then unplug the sensor's connector from the wiring harness. Remove the mounting screw(s) or clip holding the sensor to the stator and remove the old sensor. Install the new 6501KW2001B sensor in the same position, taking care to seat it at the correct distance/orientation from the rotor magnets, and secure it. Reconnect the wiring harness connector, matching your photos. Reinstall the rear panel, restore power, and run a test cycle to confirm the washer spins and agitates normally without triggering an LE error code. Tools needed: nut driver or screwdriver, needle-nose pliers (for wiring connectors). Frequently Asked Questions My washer shows an "LE" error code — is this the part I need? This is one of the most common causes of an LE (motor/rotor position) error on LG and LG-built Kenmore washers. If your washer displays LE and stops mid-cycle or won't spin, this sensor is a likely culprit. That said, LE errors can also stem from the control board or a damaged wiring harness between the sensor and the board, so if replacing the sensor doesn't resolve the error, those components are the next things to inspect. Is this the same as the 6501KW2002B sensor? No — 6501KW2001B and 6501KW2002B are different, non-interchangeable rotor position sensors used on different LG washer platforms. Confirm your exact part number from your appliance's parts diagram before ordering, since these two are easy to mix up by their similar naming. My LG washer's parts diagram doesn't show a separate rotor position sensor — why? Some newer LG models integrate the Hall sensor directly into the motor stator assembly (such as part AJB73816004) rather than using a standalone sensor like this one. If your model doesn't list a standalone sensor, check whether your repair requires the full stator assembly instead. Contact our support team with your model number if you're unsure which one applies to your washer. Do I need any special tools to install this? No special tools — a nut driver or screwdriver to access the rear panel and remove the sensor's mounting screw(s), plus needle-nose pliers to help with the wiring connector. The main thing to get right is reinstalling the new sensor at the same position and orientation relative to the rotor as the original. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

DC97-14421A Genuine OEM Washer Tub Support Description: The Spider Arm Assembly is an OEM component compatible with specific Samsung front-loading washing machines. It is the linkage mechanism connecting the transmission shaft and pulley system inside the drive motor. With integrated spring coils and joints, the multi-armed assembly facilitates smooth rotational movement of the wash basket essential for various cycles such as agitation, spinning, and drainage. Replaces Part Numbers:  DC97-14421A, 2076567, AP4452794, PS4220154.  

Read more less