Search results for "refrigerator water inlet valve"

XPARTCO 5303918214 Refrigerator Defrost Thermostat The XPARTCO 5303918214 is an aftermarket replacement defrost thermostat kit for Frigidaire, Electrolux, Kenmore, Gibson, Kelvinator, Westinghouse, and Crosley refrigerators — commonly used on side-by-side and French door models equipped with an ice maker. This thermostat monitors the temperature of the evaporator coils: when the coils drop below a set temperature, it allows power to reach the defrost heater so frost can be cleared; once the coils warm back up, it cuts power to the heater again, protecting the evaporator from being overheated during that process. The most common reasons this thermostat gets replaced are a classic pair of symptoms: the freezer stays cold while the fresh food refrigerator section runs warm, or the refrigerator simply isn't defrosting on its normal cycle. Because this thermostat sits behind the rear access panel near the ice maker on many compatible models, replacing it typically involves removing the ice maker and the back panel to reach it — a more involved repair than a thermostat mounted in an easily accessible spot. It directly replaces AP2150145, 892545, AH469522, EA469522, PS469522, and 75303918214. Quick Answer The XPARTCO 5303918214 Refrigerator Defrost Thermostat fixes Frigidaire, Electrolux, Kenmore, Gibson, Kelvinator, Westinghouse, and Crosley refrigerators where the freezer stays cold but the fresh food section runs warm, or the refrigerator isn't defrosting on its normal cycle. Replaces AP2150145, 892545, AH469522, EA469522, PS469522, 75303918214. This is a separate part from our 5303918202 defrost thermostat listing — the two fit different model groups and are not interchangeable. Installation on many compatible models requires removing the ice maker to access the thermostat. Common Problems This Part Fixes Freezer stays cold but the fresh food refrigerator section runs warm Refrigerator not defrosting on its normal cycle Excessive frost or ice buildup on the evaporator coils Refrigerator or freezer not cooling properly overall Water leaking inside the refrigerator from melting ice buildup Refrigerator running constantly as ice-caked coils reduce cooling efficiency Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This refrigerator defrost thermostat directly replaces the following OEM and cross-reference part numbers: 5303918214, 75303918214, 892545, AH469522, EA469522, AP2150145, 240372703, 39TVE31, EAP469522, PS469522, AFR16819, PD00000354, L47-22F, SL8214, ER5303918214 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This defrost thermostat is compatible with select Frigidaire refrigerators, and also fits select Electrolux, Kenmore, Gibson, Kelvinator, Westinghouse, and Crosley refrigerators built on the same platform, including model numbers such as: FGHS2631PF4A, FGHS2655PF5A FGHC2331PFAA, FGHC2331PFCA FFHS2611PFEA, FFHS2611LBRA, FFHS2611LWMA, FFHS2622MSYA FFSS2614QS6A Note — not the same as 5303918202: This is a separate thermostat from our 5303918202 listing. The two fit different model groups and are not interchangeable, so always verify your full model number rather than assuming based on similar part number prefixes. Contact our support team with your model number if you're unsure which thermostat fits your refrigerator. Key Features Aftermarket replacement defrost thermostat kit for Frigidaire-platform refrigerators with an ice maker Monitors evaporator coil temperature and controls power to the defrost heater Resolves "freezer cold, fridge warm," "not defrosting on schedule," and "icy evaporator coils" symptoms caused by thermostat failure Ships with wiring diagram guidance for a correct connection Direct drop-in replacement — mounts to the original housing location Replaces AP2150145, 892545, AH469522, EA469522, PS469522, and 75303918214 Compatible with Frigidaire, Electrolux, Kenmore, Gibson, Kelvinator, Westinghouse, and Crosley refrigerators Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number 5303918214 OEM Part Number 5303918214 Part Type Refrigerator Defrost Thermostat Kit Condition Aftermarket Replacement Function Monitors evaporator coil temperature and controls power to the defrost heater Typical Location Rear access panel area, near the ice maker on many compatible models Repair Difficulty Moderate — ice maker removal typically required for access Quantity 1 defrost thermostat kit Compatible Brands Frigidaire, Electrolux, Kenmore, Gibson, Kelvinator, Westinghouse, Crosley Installation Notes ⚠️ Unplug Refrigerator And Shut Off Water Supply Before Starting Unplug the refrigerator from the wall outlet and turn off the water supply to the refrigerator before beginning. Wear work gloves. If your model has an ice maker, remove it first using a screwdriver to gain clearance for the next steps. Remove the back panel with a screwdriver to expose the defrost thermostat. Take out the existing thermostat and disconnect its wiring, labeling or photographing each connection first. Install the new 5303918214 thermostat by connecting the wires according to the wiring diagram provided with the kit, then secure the thermostat to the main housing using the small mounting screws. Reinstall the back panel, plug the refrigerator back in, turn the water supply back on, and reinstall the ice maker. Test the refrigerator over the following day to confirm both compartments are cooling evenly and the defrost cycle is running normally. Tools needed: screwdriver, wire cutters/strippers, work gloves. Frequently Asked Questions Do I really need to remove the ice maker for this repair? On many compatible models, yes — the thermostat sits behind the rear access panel in an area that the ice maker partially blocks, so removing it first gives you the clearance needed to reach the panel and the thermostat behind it. It's an extra step compared to some simpler defrost thermostat replacements, but it's a standard part of this particular repair. My freezer is cold but the fridge is warm. Is this the thermostat? Yes, this is the classic symptom of a failed defrost thermostat. When it fails, the defrost heater can't run correctly to clear frost from the evaporator coil, and the resulting ice buildup blocks the airflow that's supposed to carry cold air to the fresh food compartment. The freezer, sitting closer to the coil, often stays reasonably cold, while the fresh food side runs warm since it depends on that circulated air. I replaced the thermostat but my freezer temperature is still fluctuating. What should I check next? Replacing this thermostat resolves the issue for most customers, but if fluctuation continues, it's worth checking the other components in the same defrost circuit — the defrost timer and defrost heater — since a failure in either of those can produce similar temperature instability even with a good thermostat installed. It's also worth confirming the door seals are sealing properly, since a poor seal lets warm air in and can cause temperature swings unrelated to the defrost system. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Frigidaire OEM part, but is manufactured to match the temperature threshold, mounting configuration, and function of the original 5303918214 defrost thermostat used in compatible Frigidaire, Electrolux, Kenmore, Gibson, Kelvinator, Westinghouse, and Crosley refrigerators. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO Washer Replacement Part XPARTCO 5220FR2075V Washer Water Valve Replaces 5221ER1003M Three-solenoid, DC12V water inlet valve assembly for select LG-built front-load washing machines. Product Overview The XPARTCO 5220FR2075V Washer Water Inlet Valve controls the flow of water entering compatible front-load washing machines. When energized by the washer control, the valve opens the required water path and directs water through the dispenser and into the tub. This is a new XPARTCO aftermarket replacement part designed to replace compatible LG inlet valve assemblies, including part number 5221ER1003M. Quick Answer XPARTCO 5220FR2075V is a three-solenoid, DC12V washer water inlet valve for select LG and LG-built Kenmore front-load washers. It replaces 5221ER1003M. Verify the complete washer model number, valve configuration, electrical connectors, and hose outlets before ordering. Common Problems This Part May Fix Washer does not fill with water Slow or restricted water filling Water continues entering after the washer is turned off Leaking from the inlet-valve area Incorrect water flow through the dispenser IE or another water-inlet-related error One or more valve solenoids do not open Replaces and Cross-References 5220FR2075V, ALG312873, AP7003066, PD00074485, PS16544738, 5221ER1003M, AP6334246, 4869495, ALG51888, EAP12579227, PD00050119, PS12579227 Cross-reference numbers help identify the compatible component. XPARTCO is an aftermarket replacement brand and is not manufactured by LG. Compatibility Designed for select LG and LG-built Kenmore front-load washers that specify 5220FR2075V, 5221ER1003M, or an approved equivalent. Compatible model examples associated with this valve family.  Important: This is only a partial compatibility list. LG water valves can look nearly identical while using different voltages, solenoid counts, mounting tabs, connectors, or outlet arrangements. Confirm the full washer model and original valve number before purchase. Key Features High-quality XPARTCO aftermarket replacement Replaces LG valve number 5221ER1003M DC12V, Three-solenoid inlet valve design Controls water entering the washer Directs water through the dispenser system Threaded inlet connection for the supply hose Designed for select LG-built front-load washers Product Specifications XPARTCO Part Number 5220FR2075V Replaces 5221ER1003M Brand XPARTCO Part Type Washer Water Inlet Valve Assembly, DC12V, 3 solenoid. Condition New Part Quality Aftermarket Replacement Valve Configuration Three Solenoids, DC12V Application Front-Load Washing Machine Included One Water Inlet Valve Assembly Installation Notes Unplug the washer and close both water-supply valves. Disconnect the inlet hose and prepare for residual water. Remove the washer top panel according to the appliance service procedure. Photograph the electrical connectors and outlet-hose locations before disconnecting them. Release the wire connectors, hose clamps, and mounting screws from the original valve. Install the replacement valve in the same orientation and reconnect every hose and wire. Open the water supplies slowly, check for leaks, restore power, and test the washer. Diagnostic tip: Confirm that the household water valves are open, inlet hoses are not kinked, and the inlet screens are not clogged before replacing the valve. Frequently Asked Questions Is XPARTCO 5220FR2075V a Genuine OEM LG part? No. It is an XPARTCO aftermarket replacement designed for compatible LG-built washers. What does the water inlet valve do? It opens and closes electrically to control water entering the washer and directs water through the dispenser system. Does this valve replace 5221ER1003M? Yes, this XPARTCO valve is sold as a replacement for 5221ER1003M on compatible washer models. Can a bad inlet valve cause an IE error? Yes. A failed solenoid, restricted valve, clogged inlet screen, or water-supply problem can cause slow filling or an inlet-related error. Will this fit every LG washer? No. Confirm the complete model number and compare the original valve number, connectors, mounting points, and hose outlets before ordering. Shop With Confidence Verify your washer model and original valve number before ordering. Our compatibility support team can help determine whether XPARTCO 5220FR2075V is correct for your appliance. XPARTCO Replacement PartFast U.S. ShippingCompatibility SupportSecure Checkout

Read more less

DA47-00311A Refrigerator Genuine Defrost Heater Replaces Part Numbers: DA47-00311A, AP5306643, PS4140651. fits specific Samsung Refrigerator models Description: This Refrigerator Defrost Heater Assembly is essential for maintaining your refrigerator's optimal performance. This Genuine OEM part ensures reliable defrost cycles, preventing ice buildup and enhancing cooling efficiency. Crafted with a durable heater sheath-metal, it withstands regular use and temperature fluctuations, providing long-lasting functionality. Installing the Refrigerator Defrost Heater Assembly helps restore your appliance defrost system, eliminating common issues like excessive frost and inconsistent temperatures. fits specific Samsung Refrigerator models

Read more less

XPARTCO WR51X10055 Refrigerator Defrost Heater Assembly The XPARTCO WR51X10055 is an aftermarket replacement refrigerator defrost heater and bracket assembly compatible with a wide range of GE, Hotpoint, Kenmore, Haier, Americana, Monogram, and Café refrigerators. The defrost heater is a glass quartz tube heater mounted on a bracket below the evaporator coils in the freezer compartment. During each automatic defrost cycle, the heater energizes and melts any frost that has accumulated on the evaporator coils — maintaining unobstructed airflow through the coils so the refrigerator can cool efficiently. When the heater fails, frost accumulates on the coils unchecked, blocking airflow and causing both the freezer and fresh food sections to gradually warm up. Rated at 120V, 725W, this single quartz tube heater assembly measures 12-1/8" L x 3-3/8" W x 2-1/8" H and includes the heater element and mounting bracket. It directly replaces WR51X10030, AP3183311, 914088, AH303781, EA303781, PS303781, SH323, and EAP303781. Often replaced together with the defrost thermostat (WR50X10068) and temperature sensor (WR55X10025) for a complete defrost system repair. Installs in 20–30 minutes with basic hand tools. Quick Answer The XPARTCO WR51X10055 Refrigerator Defrost Heater Assembly fixes GE and Hotpoint refrigerators where frost is building up on the evaporator coils, the freezer is too warm, the fresh food section is warming up, or the refrigerator is running continuously without cooling properly. Single quartz tube heater, 120V / 725W. Assembly measures 12-1/8" L x 3-3/8" W x 2-1/8" H. Includes heater and bracket. Replaces WR51X10030, AP3183311, 914088, SH323, and more. Compatible with GE, Hotpoint, Kenmore, Haier, Americana, Monogram, and Café. Common Problems This Part Fixes Frost or ice buildup covering the evaporator coils in the freezer compartment Freezer section warming up or not maintaining set temperature Fresh food section warming up even though the freezer is running Refrigerator running continuously but not cooling properly Visible frost accumulation on the freezer back wall behind the panel Defrost heater element visibly burned out, broken, or dark/charred at the ends Both compartments gradually warming up after working normally for years Replaces Part Numbers This defrost heater assembly directly replaces the following OEM and cross-reference part numbers: WR51X10055, WR51X10030, 914088, AGE29323, AH303781, AP3183311, EA303781, EAP303781, PD00001004, PS303781. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This defrost heater is compatible with select refrigerators from the following brands: GE refrigerators (side-by-side, French door, top-freezer, and bottom-freezer) Hotpoint refrigerators Kenmore / Sears refrigerators (select GE-built models) Haier refrigerators (select GE-platform models) Americana refrigerators Monogram refrigerators Café refrigerators Tip: When replacing the defrost heater, it is highly recommended to also replace the defrost thermostat (WR50X10068) and temperature sensor (WR55X10025) at the same time. These three parts form the defrost system and are commonly replaced together — replacing all three prevents a second disassembly if another component fails soon after. Key Features Single quartz tube glass heater — melts frost from the evaporator coils during each automatic defrost cycle, maintaining airflow and cooling efficiency Rated 120V / 725W — correct electrical specifications for compatible GE refrigerators Assembly dimensions: 12-1/8" L x 3-3/8" W x 2-1/8" H — direct fit into the evaporator coil bracket Includes heater element and mounting bracket — complete assembly ready to install Replaces WR51X10030 and WR51X10055 — both older and current part numbers covered Compatible with GE, Hotpoint, Kenmore, Haier, Americana, Monogram, and Café refrigerators Often replaced together with WR50X10068 defrost thermostat and WR55X10025 temperature sensor Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 20–30 minutes with basic hand tools Product Specifications Part Number WR51X10055 Also Replaces WR51X10030 Part Type Refrigerator Defrost Heater and Bracket Assembly Condition Aftermarket Replacement Heater Type Single quartz tube glass heater Voltage 120V AC Wattage 725W Dimensions 12-1/8" L x 3-3/8" W x 2-1/8" H Includes Heater element and mounting bracket Often Replaced With WR50X10068 Defrost Thermostat, WR55X10025 Temperature Sensor Compatible Brands GE, Hotpoint, Kenmore, Haier, Americana, Monogram, Café Installation Notes ⚠️ Unplug Refrigerator Before Starting — Wear Work Gloves Unplug the refrigerator before beginning. Remove all food and shelving from the freezer compartment. Remove the freezer bottom drawer and the back panel screws (typically 2 hex-head screws). Slide out the back panel to expose the evaporator coils and defrost heater assembly. If the coils are covered in frost or ice, use a hair dryer to melt the ice before removing the heater — do not chip or force the heater free while iced over, as the glass element is fragile and will break. Disconnect the heater wires from the wiring harness — note the orientation before disconnecting. Remove the 2 Phillips screws securing the heater bracket and lift the heater assembly out. Install the new WR51X10055 heater assembly in the same position, reconnect the wires, and reinstall the bracket screws. Reinstall the back panel, shelving, and food. Restore power and verify the defrost cycle operates normally. Wear work gloves throughout — the evaporator area has sharp edges. Tools needed: Phillips screwdriver, 1/4" nut driver, hair dryer (if coils are iced over), work gloves. Frequently Asked Questions What does the refrigerator defrost heater do? Modern refrigerators use an automatic defrost system that periodically runs a defrost cycle — typically once or twice a day — to melt frost that accumulates on the evaporator coils during normal operation. The defrost heater is a glass quartz heating element that energizes during this cycle and melts the frost off the coils. This keeps the coils clear so air can flow freely through them to cool the refrigerator. When the heater fails, frost builds up unchecked on the coils over days or weeks — eventually blocking airflow completely and causing both compartments to warm up, even though the compressor is still running. How do I know if my defrost heater has failed? Remove the freezer back panel to expose the evaporator coils. If the coils are heavily coated in frost or solid ice — especially if both the freezer and refrigerator sections have been warming up — a failed defrost heater is the most likely cause. You can confirm with a multimeter: disconnect the heater and probe both wire ends. A working heater shows continuity (resistance between approximately 10–200 ohms at room temperature depending on wattage). No continuity confirms the heater element has burned out. Also visually inspect the glass tube — a burned, blackened, or broken tube is a clear sign of failure. Should I also replace the defrost thermostat and temperature sensor? Yes — since the freezer must be fully emptied and the back panel removed to replace the heater, it is highly recommended to also replace the defrost thermostat (WR50X10068) and temperature sensor (WR55X10025) at the same time. All three components form the defrost system and wear at similar rates. A failed thermostat or sensor can cause the heater to run too long or not at all — replacing all three in a single repair eliminates that risk and saves you from another complete freezer teardown in the near future. My freezer is warming up but the compressor is running — is it the defrost heater? It often is — but not always. A compressor that is running but not cooling can be caused by a failed defrost heater (frost blocking airflow), a faulty evaporator fan motor (air not circulating), a defrost thermostat or timer failure, or a sealed system problem (refrigerant leak or compressor issue). The easiest way to distinguish a defrost system failure from other causes is to open the freezer and check whether frost has built up on the back panel or coils. If yes, the defrost heater is the most likely culprit. If the coils are clear and the compressor is running, look at the evaporator fan or sealed system next. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured as a single quartz tube glass heater rated at 120V/725W to match the dimensions and performance of the original WR51X10055 defrost heater assembly. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WR55X10025 Refrigerator Temperature Sensor The XPARTCO WR55X10025 is an aftermarket replacement refrigerator temperature sensor (thermistor) compatible with a wide range of GE, Hotpoint, Haier, Café, and Monogram refrigerators. The temperature sensor monitors air temperature inside the fresh food and freezer compartments and sends that data to the main control board, which uses it to regulate cooling cycles and maintain the correct set temperature. When the sensor fails, the refrigerator may run too warm, too cold, or experience erratic defrost behavior. This sensor measures approximately 1-1/4 inches long and includes 18-inch wire leads. It is constructed from white plastic and is used in both fresh food and freezer compartments depending on the model — on some models it also functions as a defrost sensor on the evaporator coil. It directly replaces OEM part numbers WR55X10025 and a large number of earlier GE thermistor part numbers. Sold individually — some models require two sensors. Installs in under 30 minutes with basic hand tools. Quick Answer The XPARTCO WR55X10025 Refrigerator Temperature Sensor fixes GE and Hotpoint refrigerators that are too warm, too cold, not defrosting, or over-defrosting. The thermistor monitors compartment temperature and communicates with the control board. Approx. 1-1/4" long with 18" leads, white plastic. Compatible with GE, Hotpoint, Haier, Café, and Monogram refrigerators. Sold individually. Common Problems This Part Fixes Refrigerator compartment running too warm — food spoiling faster than normal Refrigerator running too cold — food or liquids freezing in the fresh food section Freezer section not maintaining correct temperature Refrigerator not defrosting or defrosting too frequently Excessive frost or ice buildup on evaporator coils Refrigerator and freezer both warming up after extended defrost cycles Erratic cooling — temperatures fluctuating unpredictably Replaces Part Numbers This temperature sensor directly replaces the following OEM and cross-reference part numbers: WR55X10025, 914093, WR50X10027, WR50X10034, WR50X10055, WR50X10067, WR55X10025-50PK, WR55X10025B, WR55X10026, WR55X10027, WR55X10028, WR55X10030, WR55X10087, WR55X10088, WR55X10089, WR55X10367, WR55X10380, WR55X10661, WR55X10711, WR55X10735, WR55X10736, WR55X10737, WR55X10937, WR55X10938, WR55X10939, WR55X11121, WR55X11141, WR55X11151, WR55X11152, AH304103, EA304103, OEM9556230, AP3185407, EAP304103, AGE29661, PD00000992, PS304103 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This temperature sensor is compatible with select refrigerators from the following brands: GE refrigerators (side-by-side, French door, top-freezer, and bottom-freezer) Hotpoint refrigerators Haier refrigerators (select GE-platform models) Café refrigerators Monogram refrigerators Note: Some GE refrigerator models use two or more temperature sensors. This part is sold individually. Check your model's parts diagram or contact our support team to confirm how many sensors your model requires before ordering. Key Features Monitors fresh food and freezer compartment temperatures and communicates readings to the main control board Also functions as a defrost sensor on the evaporator coil on applicable models Fits both fresh food and freezer positions White plastic construction — durable and resistant to refrigerator temperature extremes Direct replacement for WR55X10025 and over 30 earlier GE thermistor part numbers Compatible with GE, Hotpoint, Haier, Café, and Monogram refrigerators Sold individually — verify quantity needed for your model before ordering Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in under 30 minutes with basic hand tools Product Specifications Part Number WR55X10025 Part Type Refrigerator Temperature Sensor (Thermistor) Condition Aftermarket Replacement Application Fresh food compartment, freezer compartment, and evaporator coil (defrost sensor) depending on model Sensor Body Length Approximately 1-1/4 inches Color White Material Plastic Includes Sensor with wire leads Sold As Single sensor (some models require 2 — verify before ordering) Compatible Brands GE, Hotpoint, Haier, Café, Monogram Installation Notes ⚠️ Unplug Refrigerator Before Starting Unplug the refrigerator from the power outlet before beginning any repair. To access the fresh food thermistor, locate the sensor on the left wall of the fresh food compartment — it may be clipped into a housing or bracket. Disconnect the wire connector and pull the old sensor out of its bracket. Slide the new WR55X10025 sensor into the bracket and reconnect the wire connector. To access the freezer or evaporator thermistor, remove the freezer shelves and back panel, then locate the sensor clipped to the evaporator coil bracket. Remove any tie wrap securing the sensor, pull the old sensor from the bracket, insert the new sensor, and reconnect the wire connector. Reinstall the back panel and shelves, restore power, and verify the refrigerator returns to the correct set temperature. Tools needed: Phillips screwdriver, flat pry tool (for panel clips), work gloves. Frequently Asked Questions How many temperature sensors does my GE refrigerator have? The number of sensors varies by model. Many GE French door and side-by-side refrigerators use two or three WR55X10025 sensors — one in the fresh food compartment, one in the freezer, and sometimes one on the evaporator coil. Check your model's parts diagram or contact our support team with your model number to confirm how many you need before ordering. What is a thermistor and how does it work? A thermistor is a type of resistor whose electrical resistance changes with temperature. The main control board sends a small voltage through the thermistor and measures the resistance — a higher resistance means a lower temperature, and a lower resistance means a higher temperature. The board uses this reading to decide when to run the compressor and fans to maintain the set temperature. A failed thermistor sends incorrect readings, causing the refrigerator to over-cool, under-cool, or malfunction during defrost cycles. Can a faulty temperature sensor cause the refrigerator to not defrost? Yes. On models where the WR55X10025 also serves as the defrost sensor on the evaporator coil, a faulty sensor can cause the control board to incorrectly time or skip defrost cycles entirely — leading to excessive frost or ice buildup on the evaporator coils. This frost buildup can eventually block airflow and cause both the refrigerator and freezer sections to warm up. How do I know if my temperature sensor is the cause of my cooling problem? The most reliable way to test the thermistor is with a multimeter. Disconnect the sensor and measure its resistance at room temperature — a working WR55X10025 should read approximately 16,000 ohms at 32°F, dropping as temperature increases. An open circuit (infinite resistance) or short circuit (zero resistance) reading confirms the sensor has failed. If resistance is within the normal range but the refrigerator still has issues, the control board or other components may be at fault. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured from durable plastic to match the dimensions and performance specifications of the original WR55X10025 temperature sensor. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

WPW10190981 Genuine OEM Whirlpool Refrigerator Ice Maker The WPW10190981 is a genuine Whirlpool OEM ice maker assembly for Whirlpool, Maytag, Kenmore, Jenn-Air, KitchenAid, and Amana French door refrigerators. This assembly receives water from the refrigerator's water inlet, holds it in the ice mold until it freezes, then uses a heating element to loosen the finished ice from the mold and automatically eject it — a rotating arm pushes the ice into the storage bin, and the cycle repeats until the bin is full. This is a modular-style assembly, and it does not include a new cover, ice level arm, or wire harness — these three components must be reused from your existing ice maker. If the coating on your current ice maker's mold is flaking off, or if internal components are no longer functioning correctly, replacing the assembly resolves both problems together. It directly replaces W10122533 and W10190981. Quick Answer The WPW10190981 Genuine OEM Whirlpool Refrigerator Ice Maker fixes Whirlpool, Maytag, Kenmore, Jenn-Air, KitchenAid, and Amana French door refrigerators that have stopped making ice, are producing less ice than usual, or have a mold with flaking coating. Replaces W10122533, W10190981. This assembly does not include the cover, ice level arm, or wire harness — you must transfer these three components from your old ice maker to the new one during installation. Common Problems This Part Fixes Ice maker has stopped producing ice entirely Ice maker producing less ice than it used to Ice mold coating visibly flaking or deteriorating Ice maker cycling but not ejecting ice into the bin Internal ice maker components no longer functioning correctly Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This refrigerator ice maker directly replaces the following OEM and cross-reference part numbers: WPW10190981, W10190981, 1471732, W10122533, AP6016630, AWP49581, OEM18049899, PD00007257, PS11749922 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This ice maker is compatible with select Whirlpool French door refrigerators, and also fits select Maytag, Kenmore, Jenn-Air, KitchenAid, and Amana refrigerators built on the Whirlpool platform, including model numbers such as: MFI2269VEM, MFI2269VEW, MFI2269VEB, GI0FSAXVY, KFIS20XVMS 7GI5FSAXVY1, 7GI5FSAXVY2, 7GI5FSAXVY3 7MI2569VEM1, 7MI2569VEM3 (Maytag) GI5FVAXVQ00, GI0FSAXVA01, GI0FSAXVB01, GI0FSAXVB02, GI0FSAXVQ01, GI0FSAXVY01, GI0FSAXVY03 GI5FSAXVA00, GI5FSAXVA01, GI5FSAXVB00, GI5FSAXVB01, GI5FSAXVB02, GI5FSAXVQ00, GI5FSAXVQ01 Note: Always verify your full model number before ordering, since Whirlpool uses several different ice maker designs across its French door refrigerator lineup. Contact our support team with your model number if you're unsure. Key Features Genuine Whirlpool OEM part — factory-specified mold design and cycling mechanism Automatically fills, freezes, and ejects ice into the storage bin Resolves "not making ice," "reduced ice production," and "flaking mold coating" symptoms Modular-style assembly for straightforward replacement Direct drop-in replacement for the ice maker body — reuses your existing cover, ice level arm, and wire harness Replaces W10122533 and W10190981 Compatible with Whirlpool, Maytag, Kenmore, Jenn-Air, KitchenAid, and Amana French door refrigerators Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number WPW10190981 Part Type French Door Refrigerator Ice Maker Assembly Condition Genuine OEM Brand Whirlpool Function Fills, freezes, and ejects ice via heating element and rotating arm Includes Cover, Ice Level Arm, Wire Harness No — reuse from existing ice maker Repair Difficulty Moderate — basic hand tools, some disassembly required Quantity 1 ice maker assembly Compatible Brands Whirlpool, Maytag, Kenmore, Jenn-Air, KitchenAid, Amana Installation Notes ⚠️ Unplug Refrigerator Before Starting — This Assembly Does Not Include The Cover, Ice Level Arm, Or Wire Harness Disconnect power to the refrigerator, or shut off the house circuit breaker for the appliance, before beginning. Wear work gloves. Move perishable food to a cooler for the duration of the repair. Open the freezer door and remove the ice bucket or drawer to access the ice maker. Photograph the wiring harness connection and the position of the cover and ice level arm before disconnecting anything. Remove the mounting screws securing the old ice maker in place, then disconnect the wire harness connector. Before setting the old ice maker aside, remove its cover, ice level arm, and wire harness — none of these three components are included with this replacement assembly, and you'll need to transfer all of them onto the new WPW10190981. Attach the cover, ice level arm, and wire harness from your old ice maker onto the new assembly, making sure each is seated and connected correctly. Mount the new assembly in the same position, reconnect the wire harness connector, and secure the mounting screws. Reinstall the ice bucket or drawer. Restore power and allow several hours for the first cycle to complete, confirming ice is being produced and ejected normally. Tools needed: Phillips screwdriver, work gloves. Frequently Asked Questions Does this ice maker come complete and ready to install? Not entirely — this assembly does not include a new cover, ice level arm, or wire harness. You'll need to remove these three components from your existing ice maker and transfer them onto this new assembly during installation, since only the ice maker body itself is included. My ice mold's coating is flaking. Should I replace the whole assembly? Yes. The mold coating isn't a separately serviceable part — if it's flaking off, replacing the complete ice maker assembly is the correct fix, since a damaged coating can affect ice quality and won't improve on its own. Is this a difficult repair? It's considered a moderate repair requiring basic hand tools, some disassembly of the refrigerator, and novice repair experience. The extra step of transferring the cover, ice level arm, and wire harness from your old unit adds a bit more care to the process compared to a fully complete replacement assembly, but it's manageable for a confident DIYer. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original mold design, heating element, and cycling mechanism of the ice maker originally installed in your refrigerator. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

DA97-15765C Refrigerator Genuine OEM Condenser Fan Motor Replaces Part Numbers: DA97-15765C, DA97-15765A, DA97-12842A, DA97-12842B, DA97-12842D, DA97-15765D, AP6001015, PS11733650. Description: This Refrigerator Condenser Fan Motor Assembly is an essential component designed to maintain optimal cooling performance in select Samsung refrigerator models. This Genuine OEM part ensures reliable operation by efficiently circulating air through the condenser coils, preventing overheating and maintaining consistent temperatures.

Read more less

W11210463 Washer Genuine OEM Water Valve Cross Reference Information: W11210463, W11038696, 4591539, W10701461, W10869803, W10883458, W11101906, AP6329219, PS12349269. Description: This Washer Water inlet valve is an OEM replacement part for specific Whirlpool brand washer models. The water inlet valve controls the flow of water into the washer. It opens and closes the valve to allow water to enter the washer during the wash cycle. Then it shuts off the flow of water once the cycle is complete.  If a water inlet valve goes bad, it can cause a number of issues. One of the most common symptoms is a lack of water entering the washing machine. Additionally, a faulty water inlet valve can cause the washer to overflow or leak.

Read more less

W10356257 Washer Genuine Water Valve Fits Specific Whirlpool, Maytag Washer Model Replaces Part Numbers: WPW10356257, W10356257, 1938138, W10336721, W10337338, W10352254, AP6020342, PS11753661. Description: This Water Inlet Valve is a Genuine part for specific Maytag, Whirlpool washing machine models. This part controls the flow of water into the washer during the filling cycles. This valve ensures that the correct amount of water is delivered to the tub, allowing for optimal washing performance. Common causes of a bad water inlet valve can include mineral buildup, electrical issues, or wear and tear from regular use.

Read more less

Genuine Whirlpool WPW10392132 Refrigerator Defrost Thermostat - Compatible with Whirlpool, Kenmore, KitchenAid, Maytag, Amana Product Description Maintain optimal cooling with the Genuine Whirlpool WPW10392132 Refrigerator Defrost Thermostat. This OEM defrost thermostat is designed for select Whirlpool, Kenmore, KitchenAid, Maytag, and Amana refrigerators, monitoring evaporator coil temperature to regulate the defrost cycle, preventing frost buildup and ensuring efficient cooling. It addresses issues like frost accumulation, warm refrigerator temperatures, or freezer not cooling properly, delivering reliable performance as an authentic Whirlpool part. Note: Includes one defrost thermostat with two-wire connector. Disconnect power before installation. Check defrost heater and related components for optimal performance. Replaces part numbers: WPW10392132, AP6020798, W10392132, PD00028150, EAP11754118, 2118359, PS11754118. Compatibility: Compatible with models including but not limited to: Whirlpool: ED5FVGXWS00, ED5VHGXMB10, ED5VHGXML10, GD5DHAXVY00, WRS325FDAM02 Kenmore: 106.51132210, 106.51133210, 106.51173310 KitchenAid: KSRJ25FXMS00, KSRL25FXMT00 Maytag: MSD2559XEM01, MFI2569VEM10 Amana: ASD2522WRB02, ASD2522WRW01 Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Whirlpool, Kenmore, KitchenAid, Maytag, and Amana refrigerators. ❄️ Specifications: OEM defrost thermostat, two-wire connector. 💪 Reliable Performance: Authentic Whirlpool part ensures long-lasting durability. 🛠️ Easy Installation: Requires screwdriver, pliers, work gloves; typically installed in 20–30 minutes. 🛡️ Effective Fixes: Resolves frost buildup, warm refrigerator temperatures, or freezer not cooling properly. Product Specification Part Number: Genuine Whirlpool WPW10392132 Component Type: Refrigerator defrost thermostat Material: Metal and plastic with sealed sensor Electrical Specs: 120V compatible Mounting: Clip-mounted on evaporator coil Operating Conditions: Suitable for low-temperature refrigerator environments Compliance: Prop 65 warning for California Installation Notes: Safety First: Disconnect the refrigerator from the power source before installation. Shop for high-quality Genuine appliance parts with a 30-day return policy. Keep your refrigerator cooling efficiently today! Add to cart now for a reliable fix!

Read more less

WH13X26534 Washer Genuine OEM Water Valve – Compatible with GE and Hotpoint Washers Product Description Maintain proper water flow with the WH13X26534 Washer Genuine OEM Water Valve. This factory-approved Water Inlet Valve Assembly is a Genuine OEM part for specific GE washing machine models. It is responsible for regulating the flow of water into the washing machine during designated cycles. The water inlet valve opens and closes to allow water to enter the tub at the correct times and pressures. It works in coordination with other components to fill and drain the tub as needed. Replaces Part Numbers WH13X26534, WH13X25296, WH13X25297, PD00051646, AP6891106, PS12726768. Compatibility This water valve is compatible with select GE and Hotpoint washers. Example compatible models include (but are not limited to): GE GTW465ASN1WW, GTW720BSN0WS, and Hotpoint HTW240ASK6WS. Always verify your washer’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 OEM Replacement – Genuine GE water valve for select washers 💧 Reliable Water Control – Accurately manages hot and cold water fill 💰 Cost-Effective Genuine Part – Factory-tested for long-lasting performance 🛠️ DIY Friendly – Simple installation with basic tools 🛡️ Fixes Common Issues – Resolves leaks, slow fill, or washer not filling at all 📐 Product Specification Part Number: WH13X26534 Component Type: Washer Water Valve Assembly Material: Reinforced plastic housing with metal solenoids Mounting: Direct-fit replacement Operating Conditions: Residential washer environments Compliance: Genuine OEM certified 🛠️ Installation Notes Tools Needed: Phillips screwdriver, adjustable wrench, pliers ⚠️ Safety First: Always unplug washer and shut off water supply before starting repairs. Steps: Disconnect power and water supply from the washer. Remove the top or rear access panel to locate the water valve. Detach water hoses and wiring harness from the old valve. Unscrew and remove the defective valve. Install the new WH13X26534 valve and reconnect hoses and wiring. Reassemble the washer panel, restore power, and run a test cycle. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders 🛠️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Solve washer filling problems quickly — Add to Cart Now for a reliable, factory-approved fix!

Read more less

WR30X39470 Refrigerator Genuine Ice Maker Fits specific GE refrigerator models. Replaces Part Numbers: WR30X39470, AP7192967, OEM28771870, PS16729732. Description: This Refrigerator Ice Maker Assembly is essential for restoring your refrigerator's ice production capabilities. This Genuine OEM part ensures seamless compatibility with a wide range of GE refrigerator models, providing reliable and consistent ice making. Crafted with high-quality materials, the Ice Maker Assembly delivers efficient performance, helping you maintain a steady supply of ice for your daily needs. Its sturdy design ensures long-lasting durability, reducing the need for frequent replacements. Installing this part is straightforward, allowing you to quickly get your refrigerator back to full functionality without hassle. Whether your original ice maker is malfunctioning, leaking, or has worn out over time, the Refrigerator Ice Maker Assembly offers a perfect replacement solution.   California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less