Appliance Parts

XPARTCO W11688995 (OE) Washer Water Inlet Valve (Cold) The XPARTCO W11688995 (OE — Original Equipment specification) is an aftermarket replacement cold water inlet valve built to OEM specifications, designed as a direct fit for select Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, Magic Chef, Admiral, Norge, Roper, Inglis, and Kenmore front-load washers. The cold water inlet valve is mounted at the back of the washer where the cold water supply hose connects. When the washer's control board calls for cold water during a wash cycle, the valve's internal solenoid opens, letting water flow into the tub or detergent dispenser. The valve closes the instant the control board cuts power, stopping flow precisely as the correct fill level is reached. When this valve fails, the washer may not fill with cold water at all, fill very slowly, fail to dispense fabric softener, continuously drip water into the tub even when off, or display F8E1 or LO FL error codes. Construction is blue and white plastic with metal solenoid coil, ~3"H x 4"W x 3"L, with 1/2" NPT threaded inlet for standard washer supply hose. It directly replaces W11688995, W11036930, W11316256, W11486361, AP7218603, EAP12711564, PD00086086, PS12711564, 4929298, and AP6835737. Often replaced as a pair with the hot water inlet valve (W11688994, sold separately). Installs in 10–15 minutes with basic hand tools. Quick Answer The XPARTCO W11688995 (OE) Washer Water Inlet Valve (Cold) fixes Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, and Kenmore front-load washers displaying F8E1 or LO FL error codes, not filling with cold water, filling slowly, failing to dispense fabric softener, or continuously dripping into the tub. Blue/white plastic with metal coil, 1/2" NPT thread, ~3"H x 4"W x 3"L. Aftermarket Original Equipment (OE) — built to OEM specs. Replaces W11036930, W11316256, W11486361, AP7218603, EAP12711564, PD00086086, PS12711564, 4929298, AP6835737. Often paired with the hot water valve (W11688994, sold separately). Common Problems This Part Fixes Washer not filling with cold water — valve solenoid not opening when commanded Washer filling slowly with cold water — valve partially clogged or weak solenoid F8E1 error code displayed — cold water inlet valve fault LO FL (low flow) error code — valve unable to deliver normal water flow Fabric softener not being dispensed — cold water flush to dispenser failing Water continuously dripping into the tub when the washer is off — valve stuck open or not fully closing Water leaks at the valve body — internal seal failure Wash cycles taking much longer than normal due to slow fill Replaces Part Numbers This cold water inlet valve directly replaces the following OEM and cross-reference part numbers: W11688995, W11316256, W11036930, W11486361, 4983050, PD00086086, FIX17216730, EAP17216730, OEM28874414, AP7218603, AWP46809, PS17216730. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This cold water inlet valve is compatible with select front-load washers from the following brands: Whirlpool front-load washers — WFC6810LW0, WFC9820HC0, WFC9820HW0 series Whirlpool front-load washers — WFW560CHW0, WFW560CHW1, WFW560CHW2, WFW560CHW3, WFW560CHW4 series Whirlpool front-load washers — WFW5605MC0, WFW5605MW0 series Whirlpool front-load washers — WFW5620HW0, WFW5620HW1, WFW5620HW2, WFW5620HW3 series Whirlpool front-load washers — WFW6620HC0, WFW6620HC1, WFW6620HC2, WFW6620HW0, WFW6620HW1 series Whirlpool front-load washers — WFW8620HC0, WFW8620HC1, WFW8620HC2, WFW8620HC3, WFW8620HC4, WFW8620HW0, WFW8620HW1, WFW8620HW2, WFW8620HW3, WFW8620HW4 series Whirlpool front-load washers — WFW862CHC0, WFW862CHC1, WFW862CHC2, WFW862CHC3 series Whirlpool front-load washers — WFW9620HBK1, WFW9620HBK2, WFW9620HBK3, WFW9620HC0, WFW9620HC1, WFW9620HC3, WFW9620HW0, WFW9620HW1, WFW9620HW2, WFW9620HW3 series Maytag front-load washers — MHW5630HC0, MHW5630HW1, MHW5630MBK0 series and related Amana front-load washers — NFW5800HW0, NFW5800HW1 and related models Inglis front-load washers — IFW5900HW, IFW5900HW1 and related models KitchenAid, Jenn-Air, Magic Chef, Admiral, Norge, Roper front-load washers — select Whirlpool-built models Kenmore / Sears front-load washers — select Whirlpool-built models Note: This is the cold water inlet valve (typically blue). The matching hot water inlet valve is part number W11688994 (typically red). When you replace one valve, it's a good practice to replace the other at the same time since they're the same age, both are accessible during the same repair, and the second valve will likely fail in the near term. Always verify your model number before ordering. Key Features Aftermarket Original Equipment (OE) replacement — built to OEM specifications for direct fit and performance Controls the flow of cold water into the washer during fill cycles Solenoid-actuated — opens precisely when the control board calls for cold water and closes the moment the call is dropped Resolves F8E1 and LO FL error codes when caused by a failed cold inlet valve 1/2" NPT threaded inlet for standard washer supply hose connection Dimensions: approximately 3" H x 4" W x 3" L Blue and white plastic body with metal solenoid coil — designed for long-term reliability against wash cycle pressure and temperature Replaces W11036930, W11316256, W11486361, AP7218603, EAP12711564, PD00086086, PS12711564, 4929298, and AP6835737 Compatible with Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, Magic Chef, Admiral, Norge, Roper, Inglis, and Kenmore front-load washers Often replaced together with the hot water inlet valve (W11688994, sold separately) as a paired repair Quick DIY repair — installs in 10–15 minutes with basic hand tools Product Specifications Part Number W11688995 Designation OE (Original Equipment specification) Part Type Washer Water Inlet Valve (Cold) Condition Aftermarket Replacement Application Front-Load Washers (Whirlpool platform) Water Type Cold (paired hot valve is W11688994) Inlet Thread 1/2" NPT Dimensions Approximately 3" H x 4" W x 3" L Color Blue / White Material Plastic / Metal Error Codes Resolved F8E1, LO FL (when caused by cold valve fault) Often Paired With Hot Water Inlet Valve (W11688994, sold separately) Compatible Brands Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, Magic Chef, Admiral, Norge, Roper, Inglis, Kenmore Installation Notes ⚠️ Unplug Washer and Shut Off Water Supply Before Starting — Wear Work Gloves Disconnect power and shut off both the hot and cold water supplies at the wall before beginning. Wear work gloves to protect your hands. Have towels ready — residual water remains in the supply hoses and will spill when disconnected. Pull the washer out from the wall to access the back. Remove the three 1/4" screws securing the rear edge of the top cover, push the top cover slightly back, and lift it off. Locate the inlet valves at the back of the washer — the cold valve is typically blue. Disconnect the cold water supply hose from the valve (water will drip — towels). Photograph the wire connections before disconnecting. Unplug the small electrical connector from the valve solenoid. Remove the single 3/16" mounting screw (or similar hardware, model-dependent) holding the valve in place, and disconnect any internal water hoses from the valve outlet (channel-lock pliers may help with hose clamps). Install the new W11688995 valve in the same position with the same orientation, reconnect the internal water hoses and electrical connector, and secure the mounting screw. Reconnect the cold supply hose at the wall, restore water and power, and run a test cycle to confirm normal cold water fill with no leaks. Tip: while the top cover is off, this is the ideal time to also replace the hot water valve (W11688994) — they share the same access and lifespan. Tools needed: 1/4" nut driver, 3/16" nut driver, adjustable wrench or pliers, work gloves. Frequently Asked Questions What do error codes F8E1 and LO FL mean on Whirlpool washers? Both codes indicate a water fill problem. F8E1 appears when the control board doesn't detect normal water flow during a fill cycle — typically caused by a failed inlet valve, a clogged inlet screen, kinked supply hose, or restricted water supply. LO FL (low flow) appears when the washer detects that water is flowing in, but at a rate too low to complete the fill within the expected time window. When the cold water inlet valve has failed or is partially clogged, both codes can appear together. Before replacing the valve, check that the household cold water supply is on and the supply hose isn't kinked, and inspect the inlet screen on the valve for sediment buildup. If those check out, replacing the W11688995 typically resolves the codes. My washer isn't dispensing fabric softener — could this be the cold valve? Yes — this is actually a common symptom that's often misdiagnosed. The cold water inlet valve also feeds the detergent dispenser tray on most Whirlpool front-load washers, including the fabric softener compartment. If the cold valve is clogged or failing to fully open at the right moment in the cycle, water doesn't flow through the fabric softener compartment to flush it into the tub, leaving softener pooled in the tray at the end of the cycle. If you've already cleaned the dispenser tray and water lines and the problem persists, replacing the cold inlet valve (W11688995) often resolves the issue. Should I replace the hot water valve at the same time? Yes, it's strongly recommended. The cold and hot inlet valves are essentially identical components installed side by side at the back of the washer — they're the same age, are exposed to the same wash cycle stress, and have the same expected service life. When one fails, the other is typically not far behind. Since the top cover is already off and both valves are accessible during the same repair, replacing both saves you a second teardown later. The matching hot water valve is part number W11688994 (red, sold separately) and is also available as a paired kit. My washer is dripping water into the tub even when it's off — is this the valve? Yes, that's a classic sign of a failed inlet valve. When the solenoid wears out or debris keeps the valve from sealing fully closed, water leaks past it at low rates and drips into the tub even with the washer powered off — especially noticeable as a slow puddle forming over a day or two. Since both the hot and cold valves feed into the tub, you'll want to identify which one is leaking: shut off the hot water supply at the wall and check if dripping continues. If it stops, the hot valve is at fault; if it continues, this cold valve is the cause. Replacing the W11688995 will resolve a leaking cold valve. What does "OE" mean and how is this different from an OEM Whirlpool part? "OE" stands for Original Equipment — meaning this is an aftermarket replacement part manufactured to original equipment specifications. It is engineered as a direct-fit substitute matching the dimensions, electrical specifications, and function of the original Whirlpool W11688995. It is not a genuine Whirlpool-branded OEM part, but is built to the same quality standards and performs identically when installed in compatible washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WH11X39237 Washer Drain Pump The XPARTCO WH11X39237 is an aftermarket replacement drain pump and filter assembly compatible with select GE, GE Profile, and GE 2-in-1 Washer/Dryer Combo front-load washers in the GFW510, GFW550, GFW650, GFW655, GFW850, PFW, and PFQ series. The drain pump is responsible for removing water from the washer drum during the drain and spin cycles — when it fails, the washer will not drain, will leave standing water in the drum, or will produce unusual noises during the drain cycle. This complete drain pump and filter assembly operates at 120V, 60Hz, 1.2A and includes the pump motor, impeller housing, and integrated filter. It directly replaces the discontinued WH11X29539 — WH11X39237 is the current manufacturer-approved updated part number. Also replaces AP6986715, 4962370, B25-3A04, and several additional cross-reference numbers. Installs in 30–45 minutes with basic hand tools. Quick Answer The XPARTCO WH11X39237 Washer Drain Pump fixes GE front-load washers that won't drain, leave standing water in the drum, display drain error codes, or make loud humming or grinding noises during the drain cycle. Complete pump and filter assembly. 120V/60Hz/1.2A. Replaces discontinued WH11X29539. Compatible with GE GFW510, GFW550, GFW650, GFW655, GFW850, PFW, and PFQ series. Common Problems This Part Fixes Washer not draining — standing water remaining in the drum after a cycle Drain error codes displayed on GE front-load washers (e.g. E23, E24, or pump-related codes) Loud humming, grinding, or buzzing noise during the drain cycle Washer stopping mid-cycle due to a drain fault Water leaking from around the drain pump area Drain pump running continuously but water not being expelled Pump impeller jammed by debris and motor burned out Replaces Part Numbers This drain pump directly replaces the following OEM and cross-reference part numbers: WH11X39237, WH11X29539, Hanyu B25-3A04, 9019841, PD00094541, AGE1260100, AP8054992, PS18351790. WH11X39237 is the current manufacturer-approved replacement for the discontinued WH11X29539. If your appliance documentation lists WH11X29539, this is the correct updated part. Compatibility This drain pump is compatible with select front-load washers and laundry combos from the following GE product lines: GE front-load washers — GFW510 series GE front-load washers — GFW550 series GE front-load washers — GFW650 series GE front-load washers — GFW655 series GE front-load washers — GFW850 series GE Profile front-load washers — PFW870, PFW950, PFW955 series GE Profile front-load washers — PFQ83 series GE 2-in-1 Washer/Dryer Combo (select models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Complete drain pump and filter assembly — pump motor, impeller housing, and integrated filter all included Removes water from the drum during drain and spin cycles for proper washer operation Integrated filter traps lint, coins, and debris to prevent pump impeller damage and clogs Electrical specs: 120V, 60Hz, 1.2A — correct for compatible GE front-load models WH11X39237 is the current manufacturer-approved replacement for discontinued WH11X29539 Direct replacement — installs into existing pump housing with no modification required Aftermarket replacement built to OEM-equivalent quality standards Compatible with GFW510, GFW550, GFW650, GFW655, GFW850, PFW, and PFQ series DIY-friendly repair — installs in 30–45 minutes with basic hand tools Product Specifications Part Number WH11X39237 Supersedes WH11X29539 (discontinued) Part Type Washer Drain Pump and Filter Assembly Condition Aftermarket Replacement Application GE Front-Load Washers and 2-in-1 Washer/Dryer Combos Voltage 120V AC Frequency 60 Hz Amperage 1.2A Includes Pump motor, impeller housing, and integrated filter Compatible Series GFW510, GFW550, GFW650, GFW655, GFW850, PFW870, PFW950, PFW955, PFQ83 Compatible Brands GE, GE Profile Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off the water supply before beginning any repair. Place towels and a shallow pan under the pump access area to catch residual water. Remove the front lower access panel of the washer. Before removing the pump, first clean the pump filter (WH23X38617) and check for a clogged filter or debris in the pump housing — a jammed impeller is sometimes mistaken for a failed pump. If the pump motor is confirmed failed, disconnect the wire harness and drain hoses from the old pump assembly, then unscrew or unclip the pump from the mounting bracket. Install the new WH11X39237 pump assembly, reconnect the drain hoses and secure with clamps, reconnect the wire harness, and reinstall the access panel. Restore power and water supply, then run a drain-only cycle to verify proper drainage and check for leaks. Tools needed: Phillips screwdriver, pliers, shallow pan or towels. Frequently Asked Questions What is the difference between WH11X39237 and WH11X29539? These are the same drain pump assembly — WH11X39237 is the current updated part number that GE issued to replace the discontinued WH11X29539. If your washer's documentation, parts diagram, or old pump label shows WH11X29539, the WH11X39237 is the correct replacement to order. Should I check the pump filter before replacing the drain pump? Yes — always check and clean the pump filter (WH23X38617) before replacing the drain pump. A heavily clogged filter can restrict water flow enough to mimic pump failure symptoms, and a foreign object jammed in the impeller can stall the pump motor without permanently damaging it. Remove the filter, clear any debris from the housing and impeller, and test the washer again. If the pump still fails to drain after cleaning, then pump replacement is the next step. How do I know if my drain pump has failed? A failed drain pump typically causes the washer to stop mid-cycle with a drain error code, or to finish a cycle with standing water in the drum. You may also hear a loud humming noise during the drain phase — this indicates the motor is running but the impeller is not turning (jammed or broken). A grinding noise suggests physical damage to the impeller or pump housing. If the pump is completely silent during the drain cycle despite power being delivered to it, the motor has likely burned out. Is the WH11X39237 compatible with GE Profile and GE 2-in-1 models? Yes — the WH11X39237 is compatible with select GE Profile front-load washers in the PFW870, PFW950, PFW955, and PFQ83 series, as well as select GE 2-in-1 Washer/Dryer Combo models. Always verify your specific model number before ordering to confirm compatibility. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured to match the electrical specifications and physical dimensions of the original WH11X39237 drain pump assembly. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

4681EA2001T (OE) LG Washer Drain Pump Motor - Compatible with LG, Kenmore Product Description Restore efficient drainage to your washer with the 4681EA2001T for LG Washer Drain Pump Motor. This OE part is designed for select LG and Kenmore front-load washers, expelling water from the drum after wash cycles to ensure proper operation. It addresses issues like water not draining, unusual noises, leaks, or error codes, delivering reliable performance with compatible genuine LG quality. Note: Includes one drain pump motor with impeller (housing not included; reuse existing pump housing). Disconnect power and water supply before installation. Inspect drain hoses and filter for clogs to prevent repeat failures. Replaces part numbers: 4681EA2001T, 4681EA1007G, 2003273, 4681EA1007D, 4681EA2001D, 4681EA2001N, 4681EA2001U, AH3579318, EA3579318, PD00001722, EAP3579318, AP5328388, PS3579318. Compatibility: Compatible with models including but not limited to: LG: WM3001HWA, WM8000HVA, WM8000HWA, WM2550HRCA, WM2550HWCA, WM3550HWCA, WM3070HRA, WM4070HVA, WM3070HWA, WM2350HRC, WM3360HVCA, WM2350HWC, WM2650HRA, WM3360HRCA, WM3360HWCA, WM3150HVC, WM2650HWA, WM2655HVA, WM3885HCCA, WM3150HWC, WM3885HWCA, WM2250CW, WM2450HRA, WM3987HW, WM3470HVA, WM3470HWA, WM3550HVCA, WM2455HG, WM2277HB, WM2487HRMA, WM2101HW, WM3270CW, WM3431HS, WM3770HVA Kenmore: 796.403119, 796.41072310, 796.412722 Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select LG and Kenmore front-load washers. 🔧 Specifications: 120V, 60Hz, 80W, 1.4A motor pumps water and soap out of the washer drum. 🛠️ Easy Installation: Requires screwdriver, pliers, nut driver; typically installed in 20–60 minutes with YouTube video guidance. 🛡️ Effective Fixes: Resolves draining issues, leaks, noisy operation, or "OE" error codes. Product Specification Part Number: 4681EA2001T - OE Component Type: Washer drain pump motor with impeller Material: Durable plastic and metal Mounting: Fits into existing pump housing, secured with screws and connected to wiring Electrical Specs: 120V, 60Hz, 80W, 1.4A, CL.F Operating Conditions: Suitable for high-volume water drainage in front-load washers Compliance: UL-listed component, Prop 65 warning for California Installation Notes: Safety First: Disconnect the washer from the power source and water supply before installation. Tip: Access the pump by removing the washer’s front or bottom panel; use a screwdriver and pliers to disconnect hoses and wiring, and ensure proper alignment when installing the new pump. Watch YouTube videos for step-by-step guidance. Check drain hoses and filter for clogs to avoid straining the new pump. Shop for LG OE parts with a 30-day return policy. Keep your washer draining efficiently today! Add to cart now for a reliable fix!

Read more less

XPARTCO 40111201 Dryer Drum Belt – Replaces WP40111201 – Compatible with Whirlpool, Maytag & Kenmore Dryers Product Description Restore smooth drum rotation and dependable drying performance with the XPARTCO 40111201 Dryer Drum Belt. This high-quality replacement transfers power from the motor to the dryer drum, allowing consistent tumbling during drying cycles. A worn, stretched, or broken belt can cause the drum to stop turning, produce squealing noises, or prevent the dryer from completing cycles. Replacing it with this durable XPARTCO belt ensures reliable operation and efficient drying. Replaces Part Numbers WP40111201, 40111201, 14218936, 40051501, 40051502, 59174, PD00002505, EAP11742271, AP6009126, PS11742271, R0606549, WP40111201VP, 661570V, 661570, 3387610, 3389728, 3393999, 339728, 661570VP, PD00023608, AP5983729, PS11722115. Compatibility This replacement dryer drum belt fits select Whirlpool, Maytag, Kenmore, Amana, Estate, Roper, and Crosley dryers. Example compatible models include (but are not limited to):Whirlpool WED4815EW1, WED5000DW2Maytag MEDC215EW1Kenmore 110.65132411 Always verify your dryer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM belt size, rib count, and tension 🌀 Restores Drum Rotation – Ensures smooth, consistent tumbling 💪 Reinforced Rubber Construction – Designed to resist stretching and wear 💰 Cost-Effective Repair – Reliable performance without OEM pricing 🛡️ Fixes Common Issues – Solves drum not turning, squealing noises, or belt slippage 📐 Product Specification Part Number: 40111201 Component Type: Dryer Drum Belt Material: Reinforced rubber Belt Style: Multi-rib (OEM-equivalent) 4 Rib, 93.5" Application: Motor-to-drum drive system Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver ⚠️ Safety First: Always unplug the dryer before servicing to prevent electrical shock. Steps: Disconnect dryer power and open the cabinet. Remove the drum to access the belt path. Remove the worn belt from the motor and idler pulley. Install the new XPARTCO 40111201 belt following the original routing. Reinstall the drum, reassemble panels, and restore power. Run a test cycle to confirm proper operation. ⏱️ Time Required: 30–45 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Restore smooth dryer operation — Add to Cart Now for a dependable, budget-friendly repair!

Read more less

WG446 Microwave Universal Mica Sheet, Waveguide Cover (Pack of 2) – Compatible with Most Microwave Brands Product Description Protect your microwave from sparking, arcing, and grease buildup with the WG446 Microwave Universal Mica Sheet / Waveguide Cover (Pack of 2). These high-quality aftermarket mica sheets shield the waveguide opening from moisture, steam, and food splatter, helping maintain efficient and safe microwave operation. Ideal for replacing damaged, burnt, or contaminated covers, this 2-pack offers excellent value and universal fit. Replaces Part Numbers WG446, Universal Mica Waveguide Cover and equivalent microwave mica sheet replacements Compatibility This universal waveguide cover 2-pack fits a wide range of Samsung, Whirlpool, GE, LG, Panasonic, Sharp, Kenmore, Emerson, and many other microwaves that use cut-to-fit mica sheets. Suitable for models such as (but not limited to):LG LMV1762ST, Samsung ME16H702SES, Whirlpool WMH31017HZ, GE JVM3160RFSS, Panasonic NN-SN686S. Always match the original cover’s dimensions before installation. Contact our support team if you’re unsure. ✅ Key Features 🔄 Universal Aftermarket Replacement – Cut-to-fit design works with most microwave brands 🧱 High-Heat Protection – Prevents debris from entering the waveguide and causing sparks ✂️ Trim-to-Size Sheets – Easy to cut using scissors or a utility knife 💰 2-Pack Value – Keep an extra sheet available for future replacements 🛡️ Fixes Common Issues – Eliminates sparking, burning smell, poor heating, or arcing caused by damaged covers 📐 Product Specification Part Number: WG446 Component Type: Microwave Mica Sheet / Waveguide Cover Material: Heat-resistant mica composite Dimensions: Approx. 5.9"L x 4.7"W (15 cm x 12 cm) (can be trimmed to size) Thickness: standard mica insulation Mounting: Clips or screws depending on microwave model Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Scissors or utility knife, screwdriver (if screws are used) ⚠️ Safety First: Unplug the microwave before installation. Never operate without a waveguide cover. Steps: Disconnect power and remove the old waveguide cover. Use the original cover as a template to trace and cut the new WG446 sheet. Insert the new cover into the mounting clips or secure with screws. Repeat with the second sheet if needed. Restore power and test heating. ⏱️ Time Required: 5–10 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Prevent microwave sparking and prolong appliance life — Add to Cart Now for a cost-effective, universal repair solution!

Read more less

(5 Pack) XP5KV07A Microwave High Voltage Fuse 0.7A (700mA), 5kV – Compatible with GE, LG, Whirlpool, Samsung, and Panasonic Microwaves Product Description Protect your microwave’s high-voltage system with the XP5KV07A Microwave High Voltage Fuse (0.7A, 5kV). This high-quality aftermarket replacement safeguards essential high-voltage components—including the magnetron, diode, and capacitor—from power surges and electrical overloads. If your microwave is completely dead or stops heating, a blown HV fuse is a common cause. Replacing it with this XPARTCO fuse restores safe, reliable operation. Replaces Part Numbers 5KV0.7A, 700mA 5kV Fuse, HVF-07A, AP-HV07A, and equivalent high-voltage 0.7A microwave fuses Compatibility This replacement high-voltage fuse fits many GE, LG, Samsung, Whirlpool, Panasonic, Sharp, Kenmore, Maytag, and other leading microwave brands. Common compatible models include (but are not limited to):GE JVM3160RFSS, LG LMV2031ST, Samsung ME19R7041FG, Whirlpool WMH31017HS, Panasonic NN-SN686S. Always verify your microwave’s fuse specs before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM electrical ratings and safety performance ⚡ High-Voltage Protection – Rated 0.7A (700mA) at 5,000 volts for microwave HV systems 💰 Budget-Friendly Fix – Reliable option for restoring microwave operation 🛠️ Easy Installation – Direct-fit size compatible with standard HV fuse holders 🛡️ Fixes Common Issues – Solves “microwave dead,” no heat, or fuse-blown conditions 📐 Product Specification Part Number: XP5KV07A Component Type: Microwave High Voltage Fuse Amperage: 0.7A (700mA) Voltage Rating: 5 kV Material: Ceramic-body fuse with metal end caps Dimensions: Standard HV fuse size (approx. 6×40 mm) Compliance: Meets high-voltage protection standards (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, needle-nose pliers ⚠️ Safety First: Microwave repairs involve high voltage even when unplugged. Only qualified persons should replace HV fuses. Steps (for trained technicians): Unplug the microwave and safely discharge the HV capacitor. Remove outer cabinet screws and lift the cover. Locate the high-voltage fuse near the HV transformer and capacitor. Remove the blown fuse and install the new XP5KV07A fuse. Reassemble the unit and test heating operation. ⏱️ Time Required: 10–20 minutes (professional preferred) 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Restore microwave safety and power protection — Add to Cart Now for a reliable, affordable replacement!

Read more less

XPARTCO MFG63099101 Washer Door Strike (Door Lock Hook) The XPARTCO MFG63099101 is an aftermarket replacement washer door strike — also called a door lock hook or door latch hook — compatible with a wide range of LG front-load washers and Kenmore 796-series washing machines. The door strike is the metal hook component mounted on the inside edge of the washer door. When the door closes, the hook enters the door lock switch on the front panel and engages the electromagnetic lock mechanism, signaling the control board that the door is closed and locking it for safe operation during wash and spin cycles. Without an intact door strike, the lock can't grip anything, and the washer will not start. When the strike breaks — typically from repeated use, sudden impact, or stress over thousands of door cycles — the washer will not start, may stop mid-cycle, may display DE1 or DE2 error codes, leak water around the door, or fail to lock altogether. It directly replaces MFG63099101, AGF77417823, AP5787149, 2759645, PS8752721, EAP8752721, and PD00046132. Important: replacing the strike requires removing the inside door panel to access the hook — note that the inner glass insert is loose during disassembly and must be handled carefully. Often replaced alongside the matching door lock switch (EBF61315802, sold separately). Installs in 15–20 minutes with basic hand tools. Quick Answer The XPARTCO MFG63099101 Washer Door Strike fixes LG and Kenmore 796-series front-load washers where the door won't lock, won't start, stops mid-cycle, displays DE1 or DE2 errors, or leaks at the door. Metal hook attaches to the inside of the washer door — engages the lock switch when the door closes. Replaces MFG63099101, AGF77417823, AP5787149, 2759645, PS8752721, EAP8752721, PD00046132. Often paired with the door lock switch (EBF61315802, sold separately). Common Problems This Part Fixes Washer door not latching properly — strike broken or worn down Washer not starting because the door isn't detected as locked Washer stopping mid-cycle due to a door fault DE1 or DE2 error codes displayed on the control panel Minor water drips or leaks around the door during operation — door not sealing because the strike isn't fully engaging Door strike visibly broken, chipped, or missing on the inside edge of the door Door not staying closed — strike worn from repeated impact Washer not powering on Replaces Part Numbers This washer door strike directly replaces the following OEM and cross-reference part numbers: MFG63099101, 2759645, AGF77417823, PD00046132, EAP8752721, AP5787149, PS8752721. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Note: the number printed on your original door hook may be a production batch code rather than the OEM part number — this does not affect fit. Compatibility This door strike is compatible with select LG and Kenmore 796-series front-load washers, including: LG front-load washers — WM1388HW, WM1455HWA series LG front-load washers — WM3050CW, WM3080CW, WM3170CW, WM3170CW/00, WM3180CW series LG front-load washers — WM3250HVA, WM3250HWA, WM3270CW series LG front-load washers — WM3370HRA, WM3370HVA, WM3370HVA/01, WM3370HWA, WM3370HWA/01, WM3370HWA/00 series LG front-load washers — WM3400CW, WM3500CW, WM3500CW/00, WM3555HWA, WM3555HWA/00 series LG front-load washers — WM3570HVA, WM3570HVA/00, WM3575CW series LG front-load washers — WM3600HVA, WM3600HWA, WM3600HWA/00, WM3670HRA, WM3670HRA/00, WM3670HVA, WM3670HWA series LG front-load washers — WM3700HVA, WM3700HWA, WM3770HVA, WM3770HWA series LG front-load washers — WM3900HBA, WM3900HWA series LG front-load washers — WM4000HBA, WM4000HWA, WM4270HVA, WM4270HVA/00, WM4370HKA, WM4370HWA series Kenmore / Sears washers — 796-series (79641162410, 79641162411, 79641262610, 79641283310, 79641283311, 79641302610, 79641303610, 79641382410, 79641382411, 79641383410, 79641383411, 79641482410, 79641482411, 79641483410, 79641483411, 79641582410, 79641582411, 79641583211, 79641583410, 79641583411, 79641962610, 79641963610 and many related models) Note: If both the door strike (MFG63099101) and the door lock switch (EBF61315802) have failed or are worn, replacing them together as a matched set ensures reliable door locking and prevents premature wear on the new strike. Always verify your model number before ordering. Key Features Metal door strike (door lock hook) — mounts to the inside edge of the washer door and engages the door lock switch when the door closes Resolves DE1 and DE2 error codes when caused by a broken door strike on compatible LG and Kenmore washers Restores the proper engagement between the door and latch assembly for a firm, consistent connection every cycle Durable metal construction — designed to withstand repeated opening and closing impact Replaces MFG63099101, AGF77417823, AP5787149, 2759645, PS8752721, EAP8752721, and PD00046132 Compatible with LG WM1388, WM3050, WM3170, WM3270, WM3370, WM3500, WM3570, WM3600, WM3670, WM3700, WM3770, WM3900, WM4000, WM4270, WM4370 series and Kenmore 796-series front-load washers Often replaced together with the door lock switch (EBF61315802, sold separately) Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in 15–20 minutes with basic hand tools Product Specifications Part Number MFG63099101 Part Type Washer Door Strike (Door Lock Hook / Latch Hook) Condition Aftermarket Replacement Application Front-Load Washers (LG / Kenmore LG-built platform) Location Inside edge of washer door Material Metal Often Paired With Door Lock Switch (EBF61315802, sold separately) Error Codes Resolved DE1, DE2 (when caused by broken strike) Compatible Brands LG, Kenmore (LG-built) Installation Notes ⚠️ Unplug Washer Before Starting — Don't Drop the Inner Glass Disconnect power before beginning. Wear work gloves to protect your hands. Open the washer door — if the door is stuck locked because of a broken strike, use a putty knife to pry the white latch on the door lock through the bottom service opening to release the door. With the door open, locate the screws around the perimeter of the inner door panel. Remove the screws to release the inner door panel from the outer frame. Important: the inner glass insert is loose once the panel is unscrewed — support the glass with one hand as you pry the panel away to prevent it from falling out and breaking. Note the orientation of the old door strike (the direction it points and how it's seated). Use needle-nose pliers or tweezers to pull out the retaining pin holding the old strike in place, then remove the broken strike. Install the new MFG63099101 strike in the same direction and orientation as the old one — installing it backwards will prevent the lock from engaging. Reinsert the retaining pin to secure it. Carefully reposition the glass insert into the door, reinstall the inner door panel, and tighten the screws. Restore power and run a test cycle to confirm the door locks properly and there are no leaks. Tools needed: Phillips screwdriver, needle-nose pliers or tweezers, putty knife (for stuck doors), work gloves. Frequently Asked Questions What's the difference between the door strike and the door lock switch? These are two separate parts that work together to lock the washer door. The door strike (MFG63099101) is the metal hook attached to the inside edge of the washer door — when the door closes, the hook is what physically enters the lock assembly. The door lock switch (EBF61315802) is the assembly mounted on the front panel just inside the door opening — it contains the electromagnetic mechanism that grips and locks the strike, and the electrical sensor that tells the control board the door is closed. If the strike is broken, the lock has nothing to grip and the washer won't start. If the switch is broken, the strike can still enter the slot but the lock won't engage or send the right signal. Both can fail independently, and often wear together — many repairs call for replacing both at the same time. My washer door is stuck closed — how do I get it open to install this? If the door is stuck in the locked position because the existing strike has broken off inside the lock or the lock won't release, you can use a putty knife or thin flat tool to manually release the door lock through the bottom service opening of the washer. Reach in through the access panel at the lower front of the unit and locate the white plastic latch on the back of the door lock assembly — gently push or pry it to release the mechanism. The door should then open. Once open, you can proceed with the strike installation. Always disconnect power from the washer first. The number on my old strike doesn't match — is it still compatible? In many cases, yes. LG sometimes prints production batch codes on door strikes that look like part numbers but don't match the official OEM part number. As long as your washer's parts diagram lists MFG63099101 (or one of its cross-references: AGF77417823, AP5787149, 2759645, PS8752721, EAP8752721, PD00046132), this strike is the correct fit. If you're unsure, contact our support team with your washer model number and we'll verify before you order. Should I replace the door lock switch (EBF61315802) at the same time? Not always, but often. The strike and the lock switch work together as a pair — if one is worn, the other has typically experienced the same load over thousands of cycles and is approaching the end of its service life. When a broken strike is the cause of the failure, examine the lock switch when the panel is open: if the lock mechanism shows visible wear, doesn't grip the new strike firmly, or has corroded contacts, replace it at the same time. Since the door is already partially disassembled and you have the washer apart, doing both at once saves a second repair session. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine LG OEM part, but is manufactured from durable metal to match the dimensions, mounting configuration, and lock-engagement function of the original MFG63099101 door strike used in compatible LG and Kenmore 796-series front-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WE04X24719 Dryer Start Button – Compatible with GE Dryers Product Description Restore dependable operation with the WE04X24719 Dryer Start Button. This replacement button allows you to start and control drying cycles. A worn, cracked, or unresponsive button can prevent the dryer from starting or make operation difficult. Replacing it with this replacement button ensures smooth function and reliable performance. Replaces Part Numbers WE04X24719, PD00046802, AP6034220, 4587500, PS11766637. Compatibility This start button is compatible with select GE dryers. Example compatible models include (but are not limited to): GE GTD42EASJ2WW, GE GTD65EBSJ3WS, and GE GTD45EASJ2WS. Always verify your dryer’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Reliable Replacement – Reliable aftermarket replacement for GE dryer start button 🔘 Reliable Operation – Restores start functionality for dryer cycles 💰 Cost-Effective Fix – Affordable way to replace a worn or broken button 🛠️ Quick Installation – Installs in minutes with basic tools 🛡️ Fixes Common Issues – Resolves unresponsive, cracked, or missing start button problems 📐 Product Specification Part Number: XPWE04X24719 Component Type: Dryer Start Button Material: Durable plastic construction Mounting: Snap-in design, direct replacement Operating Conditions: Residential dryer use 🛠️ Installation Notes Tools Needed: Phillips screwdriver, flathead screwdriver (if needed) ⚠️ Safety First: Always unplug dryer before starting repairs to avoid electrical shock. Steps: Unplug dryer and locate control panel. Remove panel screws to access start button assembly. Release old button from mounting clips. Insert new WE04X24719 button into slot until it clicks securely. Reassemble control panel and restore power. Test dryer to ensure button works correctly. ⏱️ Time Required: 10–15 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders 🛠️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Fix your dryer start function today — Add to Cart Now for a genuine, factory-approved repair!

Read more less

D510181 Genuine OEM Dryer Metal Door Strike - Compatible with Speed Queen, Alliance, Huebsch Product Description Secure your dryer door with the D510181 Genuine OEM Dryer Metal Door Strike. This Speed Queen-manufactured metal strike is designed as a replacement for select Speed Queen, Alliance, Huebsch, and other compatible dryers. It latches into the door catch when the dryer door is closed, ensuring a secure seal during operation. This part addresses issues like the door not closing properly or not staying closed, often caused by a worn or damaged strike. Note: Includes (1) metal door strike. Disconnect power before installation. Verify compatibility with your dryer model. Replaces part numbers: D510181, 510181, 500039, 54661, H87020228, PD00041917, TU21401, AP6284686. Compatibility: Compatible with select dryer models, including but not limited to: Speed Queen: ADE3SRGS175TW01, ADE4BRGS175TW01, ADEE9BGS175TW01, KDEBXRGS175TW01 Alliance: JDEJEAGW303EW01, JDEJGAGW303EW01, JSGJEAGW303EW01 Huebsch: YDE3TRGS171CW01, YDE4BRGS171CW01 Econowash: CA025L, CA025N Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Speed Queen, Alliance, Huebsch, Econowash, and other dryers. 🔧 Specifications: Genuine OEM Speed Queen metal door strike, corrosion-resistant. 💪 Reliable Performance: Ensures secure door closure for safe and efficient drying. 🛠️ Easy Installation: Requires pliers; typically installed in 5–10 minutes. 🛡️ Effective Fixes: Resolves door not closing or staying closed issues. Product Specification Part Number: D510181 Component Type: Dryer door strike Material: Metal Additional Specs: Corrosion-resistant metal, designed for front panel attachment  Compliance: Prop 65 warning for California Installation Notes: Safety First: Disconnect the dryer from the power source before installation. Shop for high-quality appliance parts with a 30-day return policy. Keep your dryer running safely today! Add to cart now for a reliable fix!

Read more less

Genuine Whirlpool WPW10605427 Washer Drain Pump - Compatible with Whirlpool, Maytag, KitchenAid, Amana, Kenmore Product Description Restore your washer’s performance with the Genuine Whirlpool WPW10605427 Washer Drain Pump. This OEM drain pump is designed for select Whirlpool, Maytag, KitchenAid, Amana, and Kenmore washing machines, efficiently circulating and draining water during wash and rinse cycles. It addresses issues like failure to drain, leaking, or unusual noises, delivering reliable performance as an authentic Whirlpool part. Note: Includes one drain pump with electrical connector. Disconnect power before installation. Inspect pump filter and drain hoses for clogs to ensure optimal performance. Replaces part numbers: WPW10605427, WPW10425238, W10425238, W10605427, W10799064, W10799065, W10903216, W10918044, PD00038328, EAP11756700, AP6023357, PS11756700. Compatibility: Compatible with models including but not limited to: Whirlpool: WFW72HEDW0, WFW75HEFW0, WFW90HEFC0, WFW92HEFW0 Maytag: MHW3500FW0, MHW5500FC0, MHW7100DW0 KitchenAid: KSMW1030SS0 Amana, Kenmore: (select models, verify compatibility) Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Whirlpool, Maytag, KitchenAid, Amana, and Kenmore washing machines. 💧 Specifications: OEM drain pump, 120V, stainless steel and plastic construction. 💪 Reliable Performance: Authentic Whirlpool part ensures long-lasting durability. 🛠️ Easy Installation: Requires screwdriver, pliers, and work gloves; typically installed in 15–30 minutes. 🛡️ Effective Fixes: Resolves failure to drain, leaking, or unusual noises during operation. Product Specification Part Number: Genuine Whirlpool WPW10605427 Component Type: Washer drain pump Material: Stainless steel and plastic Electrical Specs: 120 volts, AC Mounting: Screw-mounted, typically at the bottom rear of the washer Operating Conditions: Suitable for household washing machine environments Compliance: UL-listed, Prop 65 warning for California Installation Notes: Safety First: Disconnect the washer from the power source before installation. Shop for high-quality Genuine appliance parts with a 30-day return policy. Keep your washer draining efficiently today! Add to cart now for a reliable fix!

Read more less

XPARTCO DC47-00018A Dryer Hi-Limit Thermostat - Compatible with Samsung, Kenmore Dryers Product Description Prevent overheating in your dryer with the replacement DC47-00018A Dryer Hi-Limit Thermostat. This high-limit thermostat is designed for select Samsung and Kenmore dryers, shutting off the heating element or burner at 260°F and restarting at 50°F to ensure safe operation. It addresses issues like no heat, overheating, or premature shutoff, offering a cost-effective alternative to OEM parts. Note: Includes one high-limit thermostat with two 1/4" male spade terminals. Disconnect power before installation. Replaces part numbers: DC47-00018A, AP4201898, 1122485, PS4205217. WP35001092, 35001092, PD00004704, EAP11741822, AP6008682, PS11741822. Compatibility: Compatible with models including but not limited to: Samsung: DV203AES, DV209AEW/XAA-0000, DV210AEW/XAA, DV42H5000EW/A3, DV45H7000EW/A2, DV48H7400EW/A2, DV5471AEP/XAA Kenmore: 40289032010, 40289032011, 40299032010, 40299032012 Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Samsung, Kenmore, and Whirlpool dryers. 🔥 Specifications: replacement high-limit thermostat, opens at 260°F, closes at 50°F. 💰 Cost-Effective Alternative: Offers OEM-equivalent performance at a lower price. 🛠️ Easy Installation: Requires Phillips screwdriver, pliers, work gloves; typically installed in 15–20 minutes. 🛡️ Effective Fixes: Resolves no heat, overheating, or premature shutoff issues. Product Specification Part Number: XPARTCO DC47-00018A Component Type: High-limit thermostat Material: Metal and plastic Electrical Specs: L260-50F. 125/250V. 25A. Mounting: Two 1/4" male spade terminals, mounts on heater assembly Operating Conditions: Suitable for high-temperature dryer environments Compliance: Prop 65 warning for California Installation Notes: Safety First: Disconnect the dryer from the power source before installation. Shop for high-quality replacement appliance parts with a 30-day return policy. Keep your dryer safe and efficient today! Add to cart now for a budget-friendly fix!

Read more less