Appliance Parts

W11449889 Refrigerator Glass Shelf    Glass Shelf for Snack Shelf Replaces Part Numbers: W11449889, W11194630, W11226452, W11041179, W11132229, W11162570, W11166552, W11351247, AP6987249.  

Read more less

XPARTCO PB04001 Oven Bake Igniter for Viking Replaces 065650-000 The XPARTCO PB04001 is an aftermarket replacement oven bake igniter compatible with select Viking gas ranges with hot surface ignition systems, including the CVDSC, EVGIC, EVGRT, VDSC, VGIC, VGRT, VGSC, VGSS, and VGGT series. The oven bake igniter is a flat glow bar hot surface igniter — it draws electrical current through the oven's gas safety valve to open it, then heats to ignition temperature to light the gas burner. When the igniter weakens or fails, the oven will not heat, will take too long to reach temperature, or the igniter will glow but the burner will never light. This is a silicon carbide flat-style igniter with a 2.25-inch white ceramic body and 4.5-inch overall length. Wire leads extend approximately 12.5 inches from the igniter body with female insulated terminals for plug-in installation. Ceramic wire nuts for spliced installation are included. Rated 3.2–3.6 amps at 120V AC — the correct amperage range to open the Viking oven gas safety valve. It directly replaces 065650-000, PB040001, 792263, AP5315579, AP7180264, SGR4001, SGR40001, GR40001, RP712, and AR402. Sold individually. Installs in 15–25 minutes with basic hand tools. Quick Answer The XPARTCO PB04001 Oven Bake Igniter fixes Viking gas ranges where the oven won't heat, takes too long to preheat, or the igniter glows but the burner never lights. Flat silicon carbide glow bar, 3.2–3.6A, 120V AC. Ceramic body 2.25", overall 4.5", leads 12.5" with female terminals. Ceramic wire nuts included. Sold individually. Compatible with Viking CVDSC, EVGIC, EVGRT, VDSC, VGIC, VGRT, VGSC, VGSS, VGGT series. Replaces 065650-000, PB040001, 792263, AP5315579, AP7180264, SGR4001. Common Problems This Part Fixes Oven not heating at all — igniter has failed or burned out Oven takes much longer than normal to preheat Igniter glows orange but the gas burner never lights Gas smell when oven is turned on but burner does not light Oven heats on first use but fails to relight during subsequent heat cycles Igniter visibly cracked, broken, or dark/charred at the ends Oven baking inconsistently or shutting off heat mid-cycle Replaces Part Numbers This oven igniter directly replaces the following OEM and cross-reference part numbers: 065650-000, AP7180264, PB040001, PB04001, 792263, SGR40001, GR40001, RP712, AR402 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This oven igniter is compatible with select Viking gas ranges with hot surface ignition (glow bar) systems, including the following series: Viking CVDSC series — CVDSC365-4G, CVDSC485-6G and related models Viking EVGIC series — EVGIC305, EVGIC365, EVGIC485 and related models Viking EVGRT series — EVGRT360, EVGRT480, EVGRT600 and related models Viking VDSC series — VDSC365, VDSC367, VDSC485, VDSC487 and related models Viking VGIC series — VGIC245, VGIC245G, VGIC245K, VGIC245Q, VGIC305, VGIC367 and related models Viking VGSC series — VGSC300, VGSC305 and related models Viking VGSS series — VGSS300, VGSS480 and related models Viking VGRT and VGGT series — VGRT360, VGGT240 and related models Note: This igniter is for Viking ranges with hot surface (glow bar) ignition systems only. Not all Viking ranges use this style of igniter — verify your model number before ordering. Always verify compatibility before purchasing. Key Features Flat glow bar hot surface igniter — draws current through the oven gas safety valve to open it, then heats to ignition temperature to light the oven burner Silicon carbide construction — superior heat resistance, reaches 1,800°F–3,100°F operating temperature in approximately 60 seconds Draws 3.2–3.6 amps at 120V AC — correct amperage range to open the Viking oven gas safety valve Ceramic body: 2.25 inches; overall length: 4.5 inches; wire leads: approximately 12.5 inches with female insulated terminals Plug-in installation with female terminals; ceramic wire nuts included for spliced installation if needed Sold individually — one igniter per order Replaces 065650-000, PB040001, 792263, AP5315579, AP7180264, SGR4001, and more Fragile silicon carbide element — handle only by the bracket and wires; never touch the ceramic body with bare hands Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 15–25 minutes with basic hand tools Product Specifications Part Number PB04001 Also Known As PB040001 Part Type Gas Oven Bake Igniter (Flat Glow Bar Hot Surface Igniter) Condition Aftermarket Replacement Application Viking Gas Ranges with Hot Surface Ignition Igniter Style Flat glow bar, silicon carbide Amperage Draw 3.2 – 3.6 Amps Voltage 120V AC Operating Temperature 1,800°F – 3,100°F (approximately 60-second heat-up) Ceramic Body Length 2.25 inches Overall Length 4.5 inches Lead Length Approximately 12.5 inches (female insulated terminals) Includes Igniter and ceramic wire nuts Sold As Single igniter Compatible Brands Viking Installation Notes ⚠️ Gas Appliance Safety Warning This part is used in gas ranges. Always shut off the gas supply at the shutoff valve and unplug the range from the electrical outlet before beginning any repair. If you smell gas at any point during or after installation, leave the area immediately and contact your gas utility provider. If you are not confident working on gas appliances, have this part installed by a qualified appliance technician. ⚠️ Handle With Extreme Care — Fragile Silicon Carbide Element The silicon carbide igniter element is extremely fragile and will crack or break with minimal force. Never touch the ceramic bar with bare hands — oils from skin will damage the element and cause premature failure. Handle only by the bracket, wires, and ceramic wire nut connectors. To install: unplug the range and shut off gas. Remove the oven racks and oven bottom panel. Disconnect the old igniter's wire connector (or cut wires if splicing). Unscrew the mounting bracket from the burner assembly and remove the old igniter. Position the new PB04001 igniter on the burner bracket and secure with the mounting screws. If the female terminals plug directly into the existing wiring, connect them. If wires need to be spliced, use the included ceramic wire nuts — never use standard plastic wire nuts near the oven burner. Reinstall the oven bottom panel and racks. Restore gas and power, then run a test cycle to confirm the igniter heats and the burner lights within 60 seconds. Tools needed: Phillips screwdriver, work gloves. Frequently Asked Questions How does a hot surface igniter work on a Viking gas oven? The hot surface igniter is wired in series with the oven's gas safety valve. When the oven is turned on, electrical current flows through the igniter, heating the silicon carbide element until it reaches ignition temperature — typically glowing bright orange. As the element heats, its electrical resistance changes and the current draw increases to 3.2–3.6 amps. At that amperage level, the gas safety valve opens and gas flows to the burner, where the glowing igniter ignites it. If the igniter weakens and can no longer draw enough current to open the safety valve, the oven will glow but the burner will never fire — this is the most common cause of a Viking oven not heating. What is the difference between PB04001 and PB040001? PB04001 and PB040001 are the same oven igniter — PB04001 is the shortened version of the PB040001 part number. Both refer to the same flat silicon carbide glow bar igniter used on compatible Viking gas ranges. This listing covers both designations and the part functions identically regardless of which number is referenced. How do I know if my oven igniter has failed? The most common sign is an oven that glows orange but the burner never lights. A healthy igniter glows bright orange and ignites the burner within about 60 seconds. If it glows dimly, stays on indefinitely without the burner lighting, or does not glow at all when the oven is turned on, the igniter has failed. You can also test with a multimeter — with the oven cold and unplugged, a working igniter shows resistance of approximately 40–90 ohms; an open circuit confirms failure. Visually inspect the element for cracks, dark spots, or a broken ceramic bar. Why must I use ceramic wire nuts instead of standard plastic ones? Standard plastic wire nuts are not rated for the temperatures inside an oven cavity — they will melt or degrade near the burner, exposing bare wires and creating a safety hazard. Ceramic wire nuts (included with this igniter) are heat-rated for oven burner temperatures and provide a safe, permanent connection when splicing is required. Always use only ceramic wire nuts for any wiring connections near the oven burner. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Viking OEM part, but is manufactured from silicon carbide and high-temperature materials to match the electrical specifications and dimensions of the original 065650-000 oven bake igniter. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WE01X25316 Dryer Door Catch The XPARTCO WE01X25316 is an aftermarket replacement dryer door catch (also called a door latch) compatible with a wide range of GE and Hotpoint electric and gas dryers in the GTD, GTX, ETD, HTX, NTX, PTD, and YTD series. The door catch is the spring-loaded latch mechanism mounted inside the dryer door panel that snaps onto the door strike on the dryer cabinet when the door is closed, holding the door securely shut during operation and activating the door switch so the dryer can run. When the catch breaks or loses its spring tension, the door will not stay closed, the dryer will not start, or the door will pop open during a drying cycle. This replacement catch is constructed from toughened nylon with a hardened manganese steel spring — materials chosen for superior wear resistance and spring durability compared to standard nylon. It is sold individually and mounts inside the dryer door panel using a snap-in clip retained by a metal retaining ring. Installation requires partially disassembling the dryer door to access the catch from the inside. It directly replaces 4512762, AP6037347, EAP11766999, PD00042653, and PS11766999. Installs in 15–30 minutes with basic tools. Quick Answer The XPARTCO WE01X25316 Dryer Door Catch fixes GE and Hotpoint dryers where the door won't stay closed, pops open mid-cycle, or won't activate the door switch to start. Toughened nylon body with manganese steel spring. Sold individually. Mounts inside the door panel — door must be partially disassembled for installation. Compatible with GE GTD3–GTD8, GTX, ETD, HTX, NTX, PTD, and YTD series dryers. Replaces 4512762, AP6037347, EAP11766999, PD00042653, PS11766999. Common Problems This Part Fixes Dryer door will not stay closed during the drying cycle Door pops open mid-cycle, stopping the dryer Dryer will not start — door switch not being activated by worn or broken catch Door feels loose or does not click firmly when closed Door catch visibly cracked, broken, or spring missing Door requires being held or pushed closed to keep the dryer running Replaces Part Numbers This door catch directly replaces the following OEM and cross-reference part numbers: WE01X25316, 4512762, AGE24874, AP6037347, EAP11766999, PD00042653, PS11766999 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This door catch is compatible with select GE and Hotpoint gas and electric dryers from the following series: GE dryers — GTD3, GTD4, GTD5, GTD6, GTD7, GTD8 series (GTD33EASK0WW, GTD42EASJ1WW, GTD58EBSV0WS, GTD65EBPL0DG, GTD72EBSN0WS, GTD75ECPL0DG, GTD84ECPN0DG and related models) GE dryers — GTX2, GTX3, GTX4, GTX6 series (GTX22EASK0WW, GTX33EASK0WW and related models) GE dryers — ETD48 series (ETD48GASW0WB and related models) GE dryers — PTD6, PTD7, PTD9 series (PTD60EBPR1DG and related models) GE dryers — YTD7 series (YTD74E2PN2DG and related models) GE dryers — XTD series (XTD72E8ST1WS and related models) Hotpoint dryers — HTX2, HTX24 series (HTX21EASK0WW, HTX24EASK0WW, HTX24GASK0WS and related models) Hotpoint dryers — NTX6 series (NTX62E8ST0WW and related models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Holds the dryer door closed and activates the door switch so the dryer can run safely Toughened nylon body — superior wear resistance compared to standard nylon catches Hardened manganese steel spring — provides reliable, durable spring tension for thousands of open/close cycles Snap-in design — mounts inside the door panel with a metal retaining clip Replaces 4512762, AP6037347, EAP11766999, and PS11766999 Sold individually — one door catch per order Compatible with GE GTD, GTX, ETD, HTX, NTX, PTD, and YTD series dryers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number WE01X25316 Part Type Dryer Door Catch (Door Latch) Condition Aftermarket Replacement Application GE and Hotpoint Gas and Electric Dryers Material Toughened nylon / Hardened manganese steel spring Mounting Snap-in inside the door panel — metal retaining clip secures in place Sold As Single door catch Compatible Brands GE, Hotpoint Installation Notes ⚠️ Unplug Dryer Before Starting — Door Disassembly Required Unplug the dryer before beginning. Unlike simpler snap-in door catches, the WE01X25316 is mounted inside the dryer door panel and requires partially disassembling the door to access it. Open the dryer door and remove the screws on the latch side of the door (typically three screws) and the screws on the hinge side (typically five screws). Gently pry the door inner and outer panels apart — work carefully around the edge. With the panels separated, locate the old catch — use pliers to squeeze the gray retaining tabs together and push downward to release the catch from the inner panel. With needle-nose pliers, squeeze the metal retaining clip and apply downward force until the clip is free. Insert the new WE01X25316 catch into the panel opening and snap it into place, then press the retaining clip back on to lock it. Reassemble the door panels and reinstall all screws. Close the door to confirm it latches firmly. Restore power and run a short cycle to verify normal operation. Tools needed: drill driver with 1/4" bit, #1 square head bit, pliers, needle-nose pliers. Frequently Asked Questions Why does installation require disassembling the door? Unlike the snap-in door catches found on many Whirlpool-family dryers — which clip into a slot accessible from the front without disassembly — the WE01X25316 mounts inside the GE door panel between the inner and outer door skins. This is a GE-specific design that provides a cleaner door exterior but requires separating the two door panels to access and replace the catch. While it is more involved than a simple snap-in replacement, it is a well-documented DIY repair that most homeowners can complete in 15–30 minutes with the right tools. My dryer door closes but the dryer still won't start — is it the catch? It may be — a worn or cracked catch may not push far enough into the door strike to fully activate the door switch, even if the door appears closed. However, if the catch appears intact and snaps firmly onto the strike, the issue may be with the door switch itself rather than the catch. The door switch (located inside the dryer cabinet at the door opening) can be tested with a multimeter for continuity in the open and closed positions. If the switch tests open in both positions, it has failed and needs replacement independently of the door catch. Is this compatible with older GE dryers that have a different door catch style? The WE01X25316 is for newer GE GTD, GTX, HTX, and related series dryers. Older GE dryers used a different door catch kit — most notably the WE01X1158 / WE1M536 / WE1M1011 style, which is a separate catch and strike kit. If your GE dryer is an older model not in the GTD/GTX/HTX series listed above, verify your model number before ordering to confirm this is the correct catch for your dryer. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured from toughened nylon with a hardened manganese steel spring to match the dimensions and function of the original WE01X25316 door catch. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

4890JL1002M Refrigerator Shelf Glass   Compatibility and Part Cross-References This component is highly cross-compatible and is designed to fit a wide selection of bottom-freezer and standard refrigerators manufactured by LG, including specific models across the LG LFC and LRB series, as well as select Kenmore models (such as the Kenmore 795 series). Replaces Part Number 4890JL1002M, 1550723, AH3524074, EA3524074, AP5215948, PS3524074. Part number 4890JL1002M is a genuine, original equipment manufacturer (OEM) refrigerator crisper cover glass shelf made primarily by LG Electronics. It functions as the clear glass insert that sits directly inside the plastic crisper drawer frame, acting as a sturdy, tempered-glass roof for your fruit and vegetable bins while serving as a functional storage shelf above them.

Read more less

WP74010750 Genuine OEM Whirlpool Oven Bake Element The WP74010750 is a Genuine OEM Whirlpool replacement oven bake element compatible with select Whirlpool, Jenn-Air, Maytag, KitchenAid, Amana, Kenmore, Magic Chef, Admiral, Norge, and Roper electric ranges and ovens — particularly CE-series, JDS-series, and MES-series slide-in and freestanding ranges. The bake element is the lower heating element located at the bottom of the oven cavity. It provides the primary heat source for baking, roasting, and preheating. When the element coil burns through, the oven will not heat, will bake unevenly, or will trip the circuit breaker when the bake cycle is selected. This Genuine OEM part is manufactured by Whirlpool to factory specifications and is rated at 2585W with push-on terminal ends (two 1/4" high-temp connectors). It measures approximately 23-5/8" wide x 15-3/8" long with 3-3/8" inserts. It directly replaces 74010750, 74003039, 7406P425-60, 1184162, WP74010750VP, ERB0750, AP6011209, PS11744404, and several additional cross-reference numbers. Installs in 15–20 minutes with basic hand tools. Quick Answer The WP74010750 Genuine OEM Whirlpool Oven Bake Element fixes electric ovens that won't heat, bake unevenly, or trip the circuit breaker during bake. 2585W, push-on terminal ends (two 1/4" high-temp connectors), 23-5/8"W x 15-3/8"L, 3-3/8" inserts. Genuine OEM. Compatible with Whirlpool CE, Jenn-Air JDS, Maytag MES series and related brands. Replaces 74010750, 74003039, 7406P425-60, 1184162, ERB0750, AP6011209, PS11744404. Common Problems This Part Fixes Oven produces no heat — bake element coil has burned through Oven takes much longer than normal to preheat Food baking unevenly — bottom of food undercooked while top is done Bake element not glowing red during the bake cycle Visible burn marks, blistering, holes, or breaks in the element coil Oven trips the circuit breaker when the bake cycle is selected — shorted element Burning smell during a bake cycle — arcing at a weak point in the element Replaces Part Numbers This bake element directly replaces the following OEM and cross-reference part numbers: WP74010750, 74010750, 1184162, 74003039, 7406P425-60, AP6011209, AWP47950, EAP11744404, PD00002565, PS11744404, WP74010750VP. Contact our support team with your model number if you need confirmation before ordering. Compatibility This bake element is compatible with select electric ranges and ovens from the following brands and series: Whirlpool electric ranges — CE35200, CE38800 and related CE-series models Jenn-Air electric ranges — JDS8850, JDS9860 and related JDS-series slide-in models Maytag electric ranges — MES5770 and related MES-series models KitchenAid electric ranges (select models) Amana electric ranges (select models) Kenmore / Sears electric ranges (select Whirlpool-built models) Magic Chef electric ranges (select models) Admiral electric ranges Norge electric ranges Roper electric ranges Note: Always verify your exact model number before ordering — bake elements are model-specific due to differences in dimensions and terminal configuration. The WP74010750 uses 1/4" push-on terminals and specific mounting dimensions that differ from other Whirlpool-family bake elements. If you are not sure this element is the right fit, contact our support team with your model number. Key Features Genuine OEM part manufactured by Whirlpool to factory specifications — guaranteed fit and performance Primary heat source for baking, roasting, and preheating in compatible electric ovens Rated 2585W — correct wattage for compatible CE, JDS, and MES series models Push-on terminal ends — two 1/4" high-temperature connectors for direct wire attachment Dimensions: approximately 23-5/8" wide x 15-3/8" long, with 3-3/8" inserts Replaces 74010750, 74003039, 7406P425-60, 1184162, ERB0750, and AP6011209 Compatible with Whirlpool, Jenn-Air, Maytag, KitchenAid, Amana, Kenmore, Magic Chef, Admiral, Norge, and Roper electric ranges DIY repair — installs in 15–20 minutes with basic hand tools Product Specifications Part Number WP74010750 Part Type Oven Bake Element (Lower Heating Element) Condition Genuine OEM Application Electric Ranges and Ovens Wattage 2585W Terminal Type Push-on — two 1/4" high-temperature connectors Width Approximately 23-5/8 inches Length Approximately 15-3/8 inches Inserts 3-3/8 inches Compatible Brands Whirlpool, Jenn-Air, Maytag, KitchenAid, Amana, Kenmore, Magic Chef, Admiral, Norge, Roper Installation Notes ⚠️ Unplug Range or Turn Off Breaker Before Starting Disconnect power before beginning and allow the oven to cool completely. Open the oven door and remove all racks. The bake element is located at the bottom of the oven cavity. Remove the screws securing the element bracket to the rear oven wall — typically one or two Phillips screws at the back. Carefully pull the element forward toward the door to expose the two 1/4" push-on wire connectors behind the oven rear wall. Note the position of each wire before disconnecting — take a photo. Pull each wire connector off the element terminals by gripping the connector (not the wire) and pulling straight back. Connect the two wires to the new WP74010750 element's terminals, slide the element back into position, and secure the mounting screws. Restore power and run a bake cycle to confirm the element heats and glows red. Tools needed: Phillips screwdriver. Frequently Asked Questions How do I know if my bake element has failed? The clearest sign is an oven that does not heat, takes much longer than usual to preheat, or bakes food unevenly with the bottom undercooked. When the bake element is working, it should glow bright red during a bake cycle. If it does not glow at all, the element has failed. You can also visually inspect the element for burn marks, blistering, cracks, or a visible break in the coil. A multimeter continuity test will confirm failure — a working element shows continuity (resistance of approximately 10–100 ohms), while a failed element reads open circuit. If the element trips the circuit breaker when selected, the element coil has shorted to the metal housing — replace it immediately. What is the difference between WP74010750 and WP74003019? Both are Genuine OEM Whirlpool oven bake elements but for different model families and with different wattage ratings. The WP74010750 is rated 2585W and is used on CE, JDS, and MES-series electric ranges. The WP74003019 is rated 2800W and is used on a different set of models. They are not interchangeable — always verify your model number to confirm which element is correct for your oven before ordering. Is it normal for a bake element to arc or spark before it fully fails? Yes — it is not unusual for a bake element to arc or spark at a weak spot before the coil fully burns through. If you see sparking, arcing, or a bright flash from the element area, immediately turn off the oven and disconnect power. Do not use the oven again until the element has been replaced. An arcing element can damage the oven liner and, in rare cases, pose a fire risk. The good news is that once you replace the WP74010750 element, the oven should perform normally again. Are the wires interchangeable on the bake element terminals? On most electric range bake elements — including the WP74010750 — the two terminal wires are interchangeable. The bake element is a resistance heater with no polarity, so either wire can connect to either terminal and the element will heat correctly. However, it is good practice to photograph the original connection before disconnecting to ensure you reconnect in the same configuration, particularly if one wire is color-coded differently from the other. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It is the exact same bake element installed in compatible Whirlpool, Jenn-Air, Maytag, and related brand electric ranges from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO W10276397 Washer Drain Pump Replaces WPW10276397 The XPARTCO W10276397 is an aftermarket replacement washer drain pump and motor assembly compatible with a wide range of Whirlpool-family top-load washers including Whirlpool Cabrio, Maytag Centennial, Amana, Kenmore, Roper, Crosley, and Inglis. The drain pump removes water from the washer tub during the drain portion of each wash cycle. When the pump fails, the washer will not drain, will leave standing water in the tub, display error code F9E1, stop mid-cycle, or produce unusual humming or grinding noises during the drain phase. This complete drain pump and motor assembly uses a Hanyu B40-3A motor (also marked 91PS3132) and includes the integrated impeller — the impeller is not sold separately. It directly replaces WPW10276397, W10276397, WPW10276397VP, 1874334, B40-3A, LP397, AP6018417, PS11751719, and several additional cross-reference numbers. Before ordering, confirm that the drain hose and any coin trap or filter are clear — a blocked hose or clogged filter can mimic pump failure symptoms. Installs in 20–30 minutes with basic hand tools. Quick Answer The XPARTCO W10276397 Washer Drain Pump fixes Whirlpool Cabrio and Maytag Centennial top-load washers that won't drain, leave standing water, display error code F9E1, or make humming/grinding noises during the drain cycle. Complete pump and motor assembly with integrated impeller. Motor: Hanyu B40-3A / 91PS3132. Replaces WPW10276397, 1874334, B40-3A, LP397, AP6018417, PS11751719. Compatible with Whirlpool Cabrio, Maytag Centennial/MVWC/MVWX, Amana, Kenmore, Roper, Crosley, and Inglis top-load washers. Common Problems This Part Fixes Washer not draining — standing water remaining in the tub after a cycle Error code F9E1 displayed — drain pump fault or slow drain detected Washer stopping mid-cycle due to a drain fault Loud humming during the drain phase — motor running but impeller not pumping Grinding or rattling noise during drain — physical damage to impeller or pump housing Water draining very slowly — worn pump motor below rated flow Water leaking from the drain pump area Replaces Part Numbers This drain pump directly replaces the following OEM and cross-reference part numbers: WPW10276397, W10276397, 1874334, AWP50231 EAP11751719 FIX11751719, OEM24073670, PD00003595, AP6018417, PS11751719, WPW10276397VP If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drain pump is compatible with select top-load washers from the following brands and series: Whirlpool top-load washers — Cabrio series (WTW4800, WTW4810, WTW4850, WTW4900, WTW5000, WTW5200, WTW5300, WTW5500, WTW5600, WTW5640, WTW5700 and related models) Maytag top-load washers — Centennial series (MVWC200, MVWC215, MVWC300, MVWC400, MVWC415, MVWC416, MVWC425, MVWC465 and related models) Maytag top-load washers — MVWX series (MVWX500, MVWX550, MVWX600, MVWX700 and related models) Amana top-load washers (ATW, NTW series and related models) Kenmore / Sears top-load washers — 110 series (Whirlpool-built Cabrio-platform models) Roper top-load washers (RTW series) Crosley top-load washers (CAE series) Inglis top-load washers (select models) Note: This pump is for top-load washers only. Always verify your exact model number before ordering. Check and clear the drain hose and any coin trap before replacing the pump — a blocked hose can produce the same symptoms as a failed pump. Key Features Removes water from the tub during the drain and spin cycles for proper washer operation Complete pump and motor assembly — includes integrated impeller (impeller not sold separately) Motor: Hanyu B40-3A / 91PS3132 — matched to original pump specifications Resolves error code F9E1 (drain pump fault / slow drain) on compatible Whirlpool and Maytag top-load washers Replaces WPW10276397, W10276397, 1874334, B40-3A, LP397, and AP6018417 Compatible with Whirlpool Cabrio, Maytag Centennial/MVWX, Amana, Kenmore, Roper, Crosley, and Inglis top-load washers Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 20–30 minutes with basic hand tools Product Specifications Part Number W10276397 OEM Part Number WPW10276397 Part Type Washer Drain Pump and Motor Assembly Condition Aftermarket Replacement Application Top-Load Washers (Cabrio, Centennial, and related platforms) Motor Hanyu B40-3A / 91PS3132 Includes Pump motor and integrated impeller assembly Error Code Resolved F9E1 (drain pump fault / slow drain) Compatible Brands Whirlpool, Maytag, Amana, Kenmore, Roper, Crosley, Inglis Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off the water supply before beginning. Place towels and a shallow pan near the pump access area to catch residual water. The drain pump is located beneath the washer tub on Cabrio and Centennial models — access it by removing the front lower panel or by tilting the washer back and working from underneath. Disconnect the drain hose clamp and hose from the pump, then disconnect the wire harness connector. Unscrew the pump mounting screws and remove the old pump. Before installing the new pump, verify the drain hose and any coin trap or filter are completely clear of debris — a blocked hose or trap will cause the new pump to fail again. Install the new W10276397 pump in the same position, reconnect the hose and wire harness, and secure the mounting screws. Restore power and water and run a drain or spin cycle to confirm drainage and check for leaks. Tools needed: Phillips screwdriver, pliers, shallow pan, towels. Frequently Asked Questions What does error code F9E1 mean on Whirlpool Cabrio and Maytag Centennial washers? F9E1 indicates a drain fault — the washer was unable to drain within the expected time during the cycle. It can be caused by a clogged drain hose, a blocked coin trap or filter, a kinked drain hose, or a failed drain pump motor. Always check and clear the drain hose and filter before replacing the pump — a blockage is often the cause and clearing it resolves the error without needing a new pump. If the hose and filter are clear and the error persists, the pump motor has likely failed. What is the difference between W10276397 and WPW10276397? These are the same drain pump assembly. WPW10276397 is the updated Whirlpool OEM part number that superseded the original W10276397. The 1874334 and B40-3A are also cross-references for this same pump. This aftermarket replacement is compatible with all of these numbers. My washer hums but won't drain — is it the pump? A humming sound during the drain cycle without water being expelled usually means the pump motor is receiving power and running, but the impeller is not turning — either because it is jammed with debris or because the impeller shaft has broken. First check for and remove any foreign objects (coins, lint, small clothing items) from the pump area. If the impeller is clear and the pump still hums without draining, the motor or impeller is mechanically failed and the pump assembly needs replacement. Does this pump fit the Whirlpool Cabrio and Maytag Bravos washers? The W10276397 is compatible with Whirlpool Cabrio and Maytag Centennial top-load washers on the VM transmission platform. Maytag Bravos XL and Bravos X models may also be compatible depending on the specific model number — verify your exact model before ordering. Contact our support team if you need confirmation for a specific Bravos model. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured with a Hanyu B40-3A motor to match the specifications and performance of the original WPW10276397 drain pump assembly. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

WB08X10066 Microwave Halogen Light Socket Genuine GE part. Replaces Part Number WB08X10066, 3025428, AP5668406, PS3510597.  

Read more less

XPARTCO 279393 Dryer Terminal Block Screw Kit The XPARTCO 279393 is an aftermarket replacement terminal block screw kit compatible with a wide range of Whirlpool-family electric dryers including Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Admiral, Estate, Crosley, Inglis, Magic Chef, and Norge. The terminal block screws secure the dryer power cord wires to the terminal block — the connection point where 240V power enters the dryer. Loose, corroded, or damaged screws at this connection can cause intermittent power loss, blown fuses, tripped breakers, or dangerous arcing. This kit includes 3 chrome-plated screws and 3 nuts — everything needed to restore a secure, conductive connection at the terminal block. The chrome plating improves electrical conductivity and corrosion resistance. Screws measure 7/16" L x 7/16" W x 11/16" H; nuts measure 1/2" L x 1/2" W x 1/8" H. Installs in under 15 minutes with basic hand tools. Quick Answer The XPARTCO 279393 Terminal Block Screw Kit fixes electric dryers with intermittent power, blown fuses, tripped circuit breakers, hot terminals, or visible arcing and scorching at the power cord connection. Includes 3 chrome-plated screws and 3 nuts. Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Admiral, and more. Common Problems This Part Fixes Dryer has intermittent power or will not start at all Internal fuses repeatedly blowing without another clear cause Circuit breaker for the dryer repeatedly tripping Terminal block area is hot to the touch during or after operation Visible arcing, sparks, scorch marks, or smoke around the terminal block cover Heating element or motor works intermittently but not consistently Dryer power cord connection is loose, corroded, or visibly damaged Replaces Part Numbers This terminal block screw kit directly replaces the following OEM and cross-reference part numbers: 279393, 279393D, 279393VP, 3184, EAP334188, AWP39844, PD00003883, AH334188, EA334188, AP3020386, PS334188 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This terminal block screw kit is compatible with select electric dryers from the following brands: Whirlpool electric dryers Kenmore / Sears electric dryers (Whirlpool-built models) Maytag electric dryers KitchenAid electric dryers Amana electric dryers Roper electric dryers Admiral electric dryers Estate electric dryers Crosley electric dryers Inglis electric dryers Magic Chef, Norge, and Jenn-Air electric dryers Note: This kit is for electric dryers only. Gas dryers do not use a terminal block for power cord connections. Key Features Secures the dryer power cord wires to the terminal block for a safe, reliable 240V connection Kit includes 3 screws and 3 nuts — one complete set for all three terminal positions Chrome-plated metal construction — improves electrical conductivity and resists corrosion Screw dimensions: 7/16" L x 7/16" W x 11/16" H; Nut dimensions: 1/2" L x 1/2" W x 1/8" H Direct replacement for OEM part numbers 279393, 279393D, and 279393VP — no modification required Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Admiral, and more Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in under 15 minutes with basic hand tools Product Specifications Part Number 279393 Part Type Terminal Block Screw and Nut Kit Condition Aftermarket Replacement Application Electric Dryers (240V terminal block) Kit Contents 3 chrome-plated screws and 3 nuts Screw Dimensions 7/16" L x 7/16" W x 11/16" H Nut Dimensions 1/2" L x 1/2" W x 1/8" H Material Chrome-plated metal Compatible Brands Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Admiral, Estate, Crosley, Inglis, Magic Chef, Norge, Jenn-Air Dryer Type Electric dryers only ⚠️ Electrical Safety Warning This kit connects the power cord to the dryer's terminal block — a high-voltage connection carrying 240V. Always unplug the dryer and shut off the circuit breaker before beginning installation. Loose or improperly tightened terminal screws can cause arcing, overheating, blown fuses, or fire. If you are not comfortable working with high-voltage electrical connections, have this part installed by a qualified appliance technician. Installation Notes ⚠️ Unplug and Switch Off Breaker Before Starting Unplug the dryer from the wall outlet and turn off the circuit breaker for the dryer before beginning any work on the terminal block. Locate the terminal block cover plate on the back of the dryer and remove it by unscrewing the retaining screw. Use needle-nose pliers to carefully disconnect the power cord wires from the terminal block. Remove the old screws and nuts using a Phillips or flat-head screwdriver. Install the new 279393 screws and nuts into the terminal block. Reconnect the power cord wires to the correct terminals — refer to the label inside the terminal block cover or your dryer's wiring diagram to confirm wire positions. Tighten all screws firmly but do not overtighten. Replace the terminal block cover plate. Restore power and run a test cycle to verify correct operation. Tip: While the cover is off, inspect the terminal block itself (part 694431) for burn marks or damage. If the block is damaged, replace it before reinstalling. Tools needed: Phillips screwdriver, flat-head screwdriver, needle-nose pliers. Frequently Asked Questions What is the terminal block screw kit used for? The terminal block screw kit secures the three wires of the dryer's power cord (two hots and a neutral, or two hots and a ground depending on cord type) to the terminal block at the back of the dryer. This is the point where 240V power enters the machine. The screws must be firmly tightened to maintain a safe, low-resistance electrical connection. If they loosen or corrode over time, resistance increases at the connection — causing heat, arcing, blown fuses, or power loss. Can I also use this kit when installing a new dryer power cord? Yes — this kit is commonly needed when installing a new 3-wire or 4-wire dryer power cord. When switching from a 3-wire to 4-wire cord (or vice versa), the terminal block screws and nuts often need to be loosened and retightened, and replacing them with a fresh set ensures a secure, corrosion-free connection from the start. Should I also inspect the terminal block itself? Yes. While the terminal block cover is off, inspect the block itself (part 694431) for burn marks, melted plastic, or damaged terminals. If the block shows any of these signs, it should be replaced before reinstalling — new screws alone cannot fix a damaged terminal block. Contact our support team to find the correct terminal block for your model. Does this kit work for gas dryers? No. Gas dryers use a standard 120V three-prong household plug and do not have a terminal block for power cord connections. The 279393 kit is for electric dryers only, which use a 240V outlet and require a hard-wired terminal block connection for the power cord. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is made from chrome-plated metal to match the dimensions and electrical performance of the original 279393 screw kit. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

5 Pack - XPARTCO EXPHV10 Microwave High Voltage Diode The XPARTCO EXPHV10 is a universal aftermarket replacement high voltage diode (rectifier) compatible with most major microwave brands including GE, Whirlpool, Maytag, Samsung, LG, Frigidaire, Panasonic, Sharp, KitchenAid, and Kenmore. The high voltage diode is a critical component in the microwave's high-voltage circuit, working alongside the high-voltage capacitor and transformer to convert alternating current (AC) to direct current (DC) — providing the high-voltage DC power required by the magnetron to generate microwave energy and heat food. When the diode fails — due to electrical surges, overheating, or normal wear — the magnetron cannot receive the correct power supply, resulting in a microwave that runs but does not heat. A failed diode may also cause the high-voltage fuse to blow repeatedly. Rated at 12,000V DC (12 kV) with a 500mA current capacity, the EXPHV10 is a universal cross-brand replacement that meets or exceeds OEM specifications across hundreds of microwave models. ⚡ HIGH VOLTAGE SAFETY WARNING — READ BEFORE SERVICING Microwaves contain a high-voltage capacitor that can store a lethal electrical charge of up to 2,100 volts even when the microwave is unplugged. Do NOT touch any internal components without first discharging the capacitor. If you are not experienced with high-voltage appliance repair, do not attempt this repair yourself — contact a qualified appliance technician. Always unplug the microwave before opening the cabinet and discharge the capacitor using a properly insulated discharge tool before handling any internal parts. Quick Answer The XPARTCO EXPHV10 Microwave High Voltage Diode fixes microwaves that run but produce no heat, have a repeatedly blown fuse, or have a humming sound with no heating. It converts AC to DC power for the magnetron and is rated 12,000V DC / 500mA. Universal fit — compatible with most GE, Whirlpool, Maytag, Samsung, LG, Frigidaire, Panasonic, Sharp, KitchenAid, and Kenmore microwaves. Common Problems This Part Fixes Microwave runs (turntable spins, light works) but does not heat food High-voltage fuse blows repeatedly after replacement Loud humming or buzzing sound with no heating Microwave takes much longer than normal to heat food Microwave heats unevenly or inconsistently Replaces Part Numbers This diode directly replaces the following OEM and cross-reference part numbers: HV10, EXPHV10, 2CL70, 2CL77, W11256462, W10886077, AWP43735, PD00047836, AP6784287, PS12584264, WB27X1160, AGE22195, PD00026293, AP2026385, PS239843, DE91-70063D, DE91-70063A, ASM94577, PD00033057, AP4236698, PS4235633, 5304417430, AP2151558, PS472334, 6021W3B001U, AP4439834, PS3528798, 6851W1A002E, ALG51731, PD00006373, AP5203812, PS3529603, 5304456178, AP3960683, PS1532581, 3518400800, AP7110292, 5304509479, 5304472472, AFR17769, PD00040522, AP4433625, PS12071314, WPR9800486, AWP128355, PD00004942, AP6014695, PS11747959, 11QBP0237, AP5633255, PS4085135, WB27X10744, AP3792899, PS953886, WB27X35382, WB27X10930, WB18X10449, WB27X10892, WB27X10965, WB27X11035, AP6992536, PS16219547, WB27X10562, AGE1037090, AP3187536, PS239704, WP13091701, AWP634588, PD00035043, AP6005641 PS11738693, WB27X10687, AGE1019656, PD00032466, AP3207509, PS953843, WB27X10107, AP2026017, PS239224, WB27X10037, AGE22509 PD00031660, AP2025948, PS239148, WPDE91-70063D, AWP547793, PD00034036, AP6014620, PS11747873, 6021W3B001V, 6021W3B001R, AP5632506 EAP3528799, ALG51931, PD00008859, AP4438526, PS3528799, WB27X21012, AGE360033, PD00037340, AP5791119, PS8754690, 00625682, 10001605, ABS11495, PD00047510, AP5804800, PS8770335, CL04-12. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This universal high voltage diode is compatible with most microwave ovens from the following brands: GE and Hotpoint microwaves Whirlpool microwaves Maytag microwaves KitchenAid microwaves Samsung microwaves LG microwaves Frigidaire and Electrolux microwaves Panasonic microwaves Sharp microwaves Kenmore / Sears microwaves Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Converts AC to DC power in the microwave's high-voltage circuit — enabling the magnetron to generate microwave energy and heat food Rated 12,000V DC (12 kV) / 500mA — meets or exceeds OEM electrical specifications Universal fit — compatible with most major microwave brands across hundreds of models Aftermarket replacement built to OEM-equivalent quality standards Pre-terminated leads — direct drop-in replacement, no modification required Compact insulated design for safe and easy installation Budget-friendly fix for one of the most common microwave no-heat failures Product Specifications Part Number EXPHV10 Part Type High Voltage Diode (Rectifier) Condition Aftermarket Replacement Application Microwave Oven High Voltage Circuit Voltage Rating 12,000V DC (12 kV) Current Rating 500 mA Material Insulated Epoxy Body Terminals Pre-terminated leads Fit Type Universal — fits most major microwave brands Compatible Brands GE, Whirlpool, Maytag, KitchenAid, Samsung, LG, Frigidaire, Panasonic, Sharp, Kenmore Installation Notes ⚡ DANGER — HIGH VOLTAGE — DISCHARGE CAPACITOR BEFORE SERVICING Microwaves store a lethal charge in the high-voltage capacitor even when unplugged. You must discharge the capacitor before touching any internal parts. Use a properly insulated discharge tool or resistor — never a screwdriver or bare wire. Once the capacitor is safely discharged: unplug the microwave and remove the outer cover. Locate the high voltage diode — it is connected between the high-voltage capacitor and the chassis ground. Disconnect both leads, note the orientation/polarity, remove the old diode, and install the new EXPHV10 in the same position and orientation. Reconnect leads, reassemble the cover, and test heating operation. Time required: approximately 20–25 minutes. If you are unsure about any step, contact a qualified appliance technician. Frequently Asked Questions Will the EXPHV10 fit my microwave? The EXPHV10 is a universal replacement diode compatible with most GE, Whirlpool, Maytag, KitchenAid, Samsung, LG, Frigidaire, Panasonic, Sharp, and Kenmore microwaves. Use the model search above to verify, or contact our support team before ordering. What does the high voltage diode do? The high voltage diode works with the capacitor and transformer to convert AC power to high-voltage DC power — typically around 4,000 to 5,000 volts. This DC voltage powers the magnetron, which generates the microwave energy that heats food. A failed diode prevents the magnetron from receiving proper power, resulting in a microwave that runs but does not heat. How do I test if my microwave diode is bad? After safely discharging the capacitor, use a multimeter set to the diode test mode. A good diode will show continuity in one direction and no continuity in the other (one-way electrical flow). A bad diode will show either no continuity in both directions (open) or continuity in both directions (shorted). A shorted diode will also cause the fuse to blow repeatedly. My microwave fuse keeps blowing — is the diode the problem? A shorted high voltage diode is one of the most common causes of a repeatedly blown microwave fuse. When the diode shorts, it draws excess current which blows the fuse. If you replace only the fuse and it blows again immediately, test the diode and capacitor as well before replacing the fuse again. Is this an OEM or aftermarket part? This is an aftermarket universal replacement part built to OEM-equivalent electrical specifications. It is not a genuine OEM part from any specific brand, but is rated at 12,000V DC / 500mA — meeting or exceeding the requirements of most microwave high-voltage circuits. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO W11366438 Range Surface Burner Knob Product Overview The XPARTCO W11366438 Range Surface Burner Knob is designed to control the heat level of your stove burners with precision. This high-quality replacement knob restores smooth operation and enhances the appearance of your cooktop. Quick Answer If your stove knob is cracked, loose, missing, or difficult to turn, the W11366438 burner knob is likely worn out. Replacing it restores proper burner control and usability. Replaces Part Numbers Replaces OEM part number: W11366438, W11084623, 4929319, W11359382, W11505414, EAP12723935, AWP44385, PD00054489, AP6888134, PS12723935. Compatibility This surface burner knob is compatible with select Whirlpool, Maytag, and other compatible ranges. Whirlpool Ranges Maytag Ranges Always verify your appliance model number before ordering. Common Problems This Part Fixes Broken or cracked knob Knob slipping or not engaging Missing control knob Difficulty adjusting burner heat Key Features Restores precise burner control Easy push-on installation High-quality aftermarket replacement Durable construction for daily use Product Specifications Part Number: XPW11366438 Part Type: Range Surface Burner Knob Brand: XPARTCO Condition: New OEM / Aftermarket: Aftermarket Application: Range Burner Control Troubleshooting Guide Knob spins freely → Worn insert Cannot adjust flame → Damaged knob Knob falls off → Cracked fitting When Should You Replace This Knob? Replace this knob if it is cracked, loose, missing, or not functioning properly. Installation Notes ⚠️ Ensure the appliance is off. Pull the old knob straight off and push the new knob firmly onto the control shaft. Related Parts Surface Burner Valve Igniter Switch Control Panel Overlay Frequently Asked Questions Will this knob fit my range?This knob fits many Whirlpool and compatible models. Always verify your model number. Is installation difficult?No, this knob is typically push-on and easy to install. What are signs of a bad knob?Cracks, slipping, or inability to control heat settings. Is this OEM or aftermarket?This is a high-quality aftermarket replacement part. Shop With Confidence Parts-O-Matic is a U.S.-based appliance parts retailer specializing in OEM and high-quality replacement parts. We offer fast shipping, reliable products, and expert support. Fast Shipping Quality Tested Parts Compatibility Support  

Read more less