Washer Control Knobs, Agitators & Latches

XPARTCO WH01X24378 Washer / Dryer Cycle Selector Knob The XPARTCO WH01X24378 is an aftermarket replacement cycle selector knob (options knob) compatible with a wide range of GE, Hotpoint, RCA, Haier, Monogram, and Café washers and dryers. The selector knob is one of the primary user controls on the appliance's control panel — it's what you grip and turn to choose the wash or dry options and settings for each load. On many GE-platform washers and dryers, this smaller selector knob works alongside a larger main timer/cycle knob to give you fine-grained control over the specific options within your selected cycle. Over time, selector knobs wear out from repeated twisting motions, get cracked or dropped, or lose their grip on the internal shaft — all of which make it difficult or impossible to change the appliance's settings. Constructed from heat-resistant plastic with a clean white and chrome finish. Snap-on installation — no tools required. Pulls straight off the control shaft and pushes back on. This knob directly replaces WH01X24378, AP5986397, 4396548, and PS11726904. Important: this is the smaller cycle selector/options knob. If you need the larger main timer knob for your GE washer, that's a different part number (PS11736611) — check which knob is broken before ordering. Installs in under 1 minute — no tools required. Quick Answer The XPARTCO WH01X24378 Washer Cycle Selector Knob replaces a cracked, loose, stripped, or missing selector knob on GE, Hotpoint, RCA, Haier, Monogram, and Café washers and dryers. Heat-resistant plastic, white and chrome finish. Snap-on installation — pulls straight off, pushes back on. Replaces AP5986397, 4396548, PS11726904. This is the smaller cycle/options knob — NOT the larger main timer knob (PS11736611). No tools required. Common Problems This Part Fixes Selector knob cracked, broken, or split from age and repeated use Knob loose and slipping on the control shaft — no longer changes settings when turned Knob has stripped or damaged internal grip and won't stay coupled to the shaft Knob missing entirely from the control panel Knob damaged from impact — dropped or bumped Knob discolored, faded, or worn from years of daily handling Difficulty selecting cycle options — knob no longer clicks into detent positions cleanly Water or detergent damage to the knob material Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This cycle selector knob directly replaces the following OEM and cross-reference part numbers: WH01X24378, 4396548, AGE26094, AP5986397, EAP11726904, OEM17959200, PD00037085, PS11726904. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This selector knob is compatible with select washers and dryers from the following brands: GE washers — GTW500ASNWS and related top-load models GE dryers — GTX42GASJWW, GTD45GASJ2WS and related models GE Profile and GE Café washers and dryers (select models) GE Monogram washers and dryers (select models) Hotpoint washers and dryers (select models) RCA washers and dryers (select GE-built models) Haier washers and dryers (select models using GE-platform controls) Important — Two Knobs, Two Part Numbers: Many GE washers and dryers have TWO knobs on the control panel: a larger main timer/cycle knob and a smaller cycle selector/options knob. The WH01X24378 is the smaller cycle selector/options knob. If your broken knob is the larger main timer knob, you need a different part number (PS11736611 on many GE models). Before ordering, visually confirm which knob is broken and compare the size and shape to the images. Contact our support team with your model number if you're unsure. Key Features Cycle selector/options knob — used to choose specific settings within your selected wash or dry cycle Snap-on installation — pulls straight off the control shaft, pushes straight back on; no tools or hardware required Heat-resistant plastic construction — designed for years of daily use without warping or cracking Clean white and chrome finish complements GE appliance styling Ergonomic shape for comfortable grip and precise cycle selection Restores full cycle control when the original knob has cracked, stripped, or gone missing Replaces WH01X24378, AP5986397, 4396548, and PS11726904 Compatible with GE, Hotpoint, RCA, Haier, Monogram, and Café washers and dryers Important: this is the smaller cycle selector/options knob — NOT the larger main timer knob (PS11736611, sold separately) Aftermarket replacement built to OEM-equivalent quality standards Quick replacement — installs in under 1 minute Product Specifications Part Number XPWH01X24378 Part Type Washer/Dryer Cycle Selector Knob (Options Knob) Condition Aftermarket Replacement Application Washers and Dryers (GE platform) Knob Size Smaller cycle/options knob (NOT the larger main timer knob) Color White / Chrome Material Heat-resistant plastic Installation Snap-on — no tools required Larger Timer Knob Different part — PS11736611 (sold separately) Compatible Brands GE, Hotpoint, RCA, Haier, Monogram, Café Installation Notes ⚠️ Unplug Washer/Dryer Before Starting — Quick Toolless Replacement Disconnect power before beginning as a general safety precaution. Wear work gloves if desired. Locate the old cycle selector knob on the control panel of your washer or dryer. Grip the knob firmly and pull it straight off the control shaft — it should come off with a moderate pull (no tools or hardware required). If the knob is stuck or the internal grip has stripped and it's spinning without releasing, use a soft cloth wrapped around it for better grip, or gently pry it off with a plastic tool (avoid metal tools that could damage the control panel finish). Once the old knob is off, inspect the metal or plastic control shaft — if it's damaged, worn round, or spinning freely with no resistance, the underlying switch or shaft may also need replacement. If the shaft is intact, align the new WH01X24378 knob with the flat sides of the shaft (the knob has a matching D-shape or flat receiver inside) and push it firmly into place until it seats fully. Rotate the knob through its full range of positions to confirm it clicks into detents cleanly and turns smoothly. Restore power and run a test cycle. Tools needed: None (soft cloth optional). Frequently Asked Questions Is this the smaller or larger knob on my GE washer? The WH01X24378 is the smaller cycle selector (options) knob. Many GE washers and dryers have two knobs on the control panel: a larger main timer/cycle knob that selects the primary wash program, and a smaller cycle options knob (this one) that selects sub-options like temperature, spin speed, or soil level. Before ordering, look at your control panel and identify which knob has failed — if the smaller knob is broken, this is the correct part. If the larger main timer knob is broken, you need a different part (PS11736611 on many GE models). The two knobs are not interchangeable. How do I remove the old knob if it's cracked or spinning without coming off? If the internal grip on the old knob has stripped and it's spinning freely on the shaft without releasing, wrap a soft cloth around it for extra grip and pull firmly straight up. If that still doesn't work, gently pry it off with a plastic pry tool (a plastic putty knife or credit card can work). Avoid metal tools that could scratch the control panel finish. If the knob is cracked, you can sometimes break away the broken pieces to expose the internal grip on the shaft, then work each piece off. Once the old knob is off, inspect the control shaft — if it's damaged or spinning without resistance, the underlying switch may need replacement too. Do I really not need any tools for this? Correct — the WH01X24378 uses a snap-on installation with no screws or hardware. To install, align the new knob with the flat side (D-shape) of the control shaft and push it straight down until it seats fully. The whole replacement typically takes under a minute. Just make sure the knob is fully seated and rotates through all positions with the correct detent clicks before you plug the appliance back in. The knob installs fine but my washer still doesn't change settings — what next? If the new knob is installed correctly (fully seated and rotates through positions with detent clicks) but changing the knob position doesn't change the cycle behavior, the underlying selector switch or control shaft has likely failed — not the knob. Common causes include the shaft spinning freely without engaging the switch inside (the shaft has stripped or broken), or the electrical selector switch itself has failed. In these cases, replacing just the knob won't fix the problem — the switch assembly behind the panel also needs to be replaced. Contact our support team with your model number for the correct switch part number. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured from heat-resistant plastic to match the dimensions, D-shape shaft receiver, snap-on installation, and cycle selection function of the original WH01X24378 selector knob used in compatible GE, Hotpoint, RCA, Haier, Monogram, and Café washers and dryers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO W10734521 Washer Clutch Slider Kit The XPARTCO W10734521 is an aftermarket replacement washer clutch slider kit compatible with a wide range of Whirlpool, Maytag, Kenmore, KitchenAid, Amana, Crosley, Estate, Jenn-Air, Roper, Magic Chef, Admiral, and Kirkland HE top-load washers. The clutch slider kit is part of the drive system that engages and disengages the inner tub from the gearcase — it's responsible for transitioning the washer between agitation and spin modes. The slider gear works together with the electromagnetic clutch and gearcase to move the inner tub during the wash and spin portions of every cycle. When the slider or its spring fails, the washer typically won't spin properly, won't agitate, makes grinding noise, or leaves clothes soaking wet at the end of a cycle. This kit includes the slider, spring support, 30mm spiral, and bolt. Slider dimensions: 2-7/8" outer diameter x 7/8" deep. Support spring: 1-5/8" outer diameter x 1-1/8" long. Spiral: 1-5/16" outer diameter. Bolt: 7/8" head diameter x 1" high. Construction is metal and plastic in black, white, and gray. Important: this is the slider kit only — it does NOT include the electromagnetic clutch (sold separately as W10754448). The current W10734521 part number supersedes the earlier W10006484, W10006494, W10275082, W10447975, and W10905025. It also replaces 3452506, AP5952873, EAP10060062, PD00025495, and PS10060062. Installs in 60–90 minutes with basic hand tools. Quick Answer The XPARTCO W10734521 Washer Clutch Slider Kit fixes Whirlpool, Maytag, Kenmore, KitchenAid, and related HE top-load washers that won't spin or agitate properly, won't transition between cycle phases, leave clothes soaking wet, or make grinding noise during the spin cycle. Slider kit only — electromagnetic clutch (W10754448) is sold separately. Includes slider (2-7/8" OD), spring support (1-5/8" OD), 30mm spiral, and bolt. Replaces W10006484, W10006494, W10275082, W10447975, W10905025, 3452506, AP5952873, EAP10060062, PD00025495, PS10060062. Common Problems This Part Fixes Washer won't spin or spins very slowly — slider not engaging the gearcase for spin mode Washer won't agitate — slider not transitioning the drive system to agitation mode Clothes left soaking wet at the end of the cycle — incomplete spin Grinding, rattling, or clunking noise during the spin or agitation phase Washer fills and drains normally but never spins or agitates Worn or broken slider gear teeth visible on the drive assembly Weak or broken slider spring — washer drive losing positive engagement Repeated cycle interruptions in the spin or agitation portion of cycles What's in the Kit Part 1 Slider Gear 2-7/8" outer diameter x 7/8" deep · Slides over the drive assembly shaft to engage/disengage the gearcase for agitation and spin transitions · Install with the teeth facing outward Part 2 Spring Support 1-5/8" outer diameter x 1-1/8" long · Provides return tension for the slider · Replace whenever the gearcase or slider is replaced — spring can weaken over time Part 3 30mm Spiral 1-5/16" outer diameter · Spiral retaining component that holds the slider assembly together on the drive shaft Part 4 Bolt 7/8" head diameter x 1" high · Secures the assembly Replaces Part Numbers This clutch slider kit directly replaces the following OEM and cross-reference part numbers: W10734521, 3452506, W10006484, W10006494, W10275082, W10447975, AP5952873, AWP41487, EAP10060062, PD00025495, PS10060062. W10734521 is the current production part superseding W10006484, W10006494, W10275082, W10447975, and W10905025. Contact our support team with your model number if you need confirmation before ordering. Compatibility This clutch slider kit is compatible with select HE top-load washers from the following brands: Whirlpool top-load washers (Cabrio, WTW5000, WTW5500, WTW5700, WTW6000, WTW6200, WTW6400, WTW7000, WTW7120, WTW8000, WTW8200, WTW8500, WTW8700 series and related models) Maytag top-load washers (Bravos and Centennial series and related models) Kenmore / Sears top-load washers (Whirlpool-built — select 110-series and related models) KitchenAid top-load washers (select models) Amana top-load washers (select models) Crosley top-load washers (select models) Estate top-load washers (select models) Jenn-Air top-load washers (select models) Roper top-load washers (select models) Magic Chef top-load washers (select models) Admiral top-load washers (select models) Kirkland top-load washers (select models) Important — Slider Kit Only, NOT Clutch: This is the clutch slider kit (slider, spring, spiral, bolt) — it does not include the electromagnetic clutch assembly. The electromagnetic clutch is part number W10754448 and is sold separately. If you need both components, order each part separately. Many repair scenarios call for replacing both at the same time, since both wear together. Always verify your model number and confirm exactly which component has failed before ordering. Key Features Complete slider repair kit — slider, spring support, 30mm spiral, and bolt included as a matched set Works with the electromagnetic clutch and gearcase to drive the inner tub during agitation and spin modes Resolves "won't spin," "won't agitate," and "clothes left soaking wet" symptoms when the slider has worn or the spring has weakened Current production part number — supersedes W10006484, W10006494, W10275082, W10447975, and W10905025 Slider: 2-7/8" outer diameter x 7/8" deep · Spring: 1-5/8" OD x 1-1/8"L · Spiral: 1-5/16" OD · Bolt: 7/8" head x 1"H Metal and plastic construction in black, white, and gray Important: slider kit only — electromagnetic clutch (W10754448) sold separately For full performance, replace all components in the kit together as a set Compatible with Whirlpool, Maytag, Kenmore, KitchenAid, Amana, Crosley, Estate, Jenn-Air, Roper, Magic Chef, Admiral, and Kirkland HE top-load washers Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 60–90 minutes with basic hand tools Product Specifications Part Number W10734521 Supersedes W10006484, W10006494, W10275082, W10447975, W10905025 Part Type Washer Clutch Slider Kit Condition Aftermarket Replacement Application HE Top-Load Washers (Whirlpool platform) Includes 1x Slider, 1x Spring Support, 1x 30mm Spiral, 1x Bolt Slider Dimensions 2-7/8" Outer Diameter x 7/8" Deep Spring Support Dimensions 1-5/8" Outer Diameter x 1-1/8" Long Spiral Dimensions 1-5/16" Outer Diameter Bolt Dimensions 7/8" Head Diameter x 1" High Material Metal / Plastic Color Black / White / Gray Electromagnetic Clutch NOT included — see W10754448 (sold separately) Compatible Brands Whirlpool, Maytag, Kenmore, KitchenAid, Amana, Crosley, Estate, Jenn-Air, Roper, Magic Chef, Admiral, Kirkland Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting — Wear Work Gloves Disconnect power and turn off the water supply before beginning. Place towels under the washer — some residual water may spill from hoses during disassembly. Wear work gloves to protect your hands. Unthread the hot and cold water supply hoses from the inlet valve ports. Disconnect the drain hose from the outlet port using channel-lock pliers to release the spring clamp. Carefully tip the washer onto its side or back on a padded surface to access the underside. Disconnect the wiring harnesses to the drive motor and pull the rotor free — be prepared for some resistance, as the permanent magnets in the rotor require some effort to remove. Use a small awl inserted between the slider gear teeth to release the spring retainer. With the retainer released, pull off the old spring and slider gear. Note the orientation of the slider — teeth facing outward. Install the new W10734521 components in sequence: slide the new slider gear onto the drive assembly shaft with teeth facing outward, install the new spring support and 30mm spiral, and secure with the new bolt. Reinstall the rotor (the magnets will pull it into place), reconnect the wiring harnesses, return the washer to upright, reconnect supply hoses and drain hose, restore power and water, and test the spin cycle for proper function. Tools needed: Phillips screwdriver, socket set, channel-lock pliers, small awl, padded surface for tipping, work gloves. Frequently Asked Questions What's the difference between W10734521 and W10754448? These are two different parts in the same drive system. The W10734521 is the clutch slider kit — it includes the slider gear, spring support, spiral, and bolt that physically engage/disengage the inner tub from the gearcase to transition between agitation and spin modes. The W10754448 is the electromagnetic clutch itself — the electrical component that drives the engagement. Both can fail independently, and many repair scenarios call for replacing both at the same time since they work together. Confirm exactly which component has failed before ordering, or order both if you're rebuilding the drive system as a full repair. My washer won't spin — is it the slider or something else? A washer that won't spin can have several causes: a failed slider kit, a failed electromagnetic clutch (W10754448), a damaged drive belt, a failed motor or rotor, a broken lid switch, or — on some models — a failed gearcase. The slider kit is one of the more common causes when the symptom is "fills and drains but won't spin" with no obvious noise or burning smell. Before replacing the slider, check that the lid latch strike (W11457841 on some models) is engaging properly, the drive belt is intact, and the motor is functioning. If those check out and the slider gear shows visible wear, missing teeth, or a stretched spring, the W10734521 kit is the right repair. Should I replace all parts in the kit together? Yes — for the kit to perform as designed, all components should be replaced as a matched set. The slider, spring support, spiral, and bolt all work together — if one is worn, the others have typically experienced the same load and wear. Reusing old components alongside new ones can cause premature failure of the new parts and a repeat repair. The W10734521 kit is priced and packaged for a complete replacement, so install all four pieces during your repair. What is the difference between W10734521 and the older part numbers it replaces? W10734521 is the current production version of this slider kit. It directly supersedes W10006484, W10006494, W10275082, W10447975, and W10905025 — all of which were earlier OEM part numbers for variations of the same slider kit across production revisions. Whirlpool consolidated these into the W10734521 to streamline the parts catalog. If your washer's parts diagram shows any of these older numbers, the W10734521 is the correct current replacement. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured from metal and plastic to match the dimensions, gear profile, and drive engagement function of the original W10734521 clutch slider kit used in compatible Whirlpool, Maytag, Kenmore, and related HE top-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

DC66-00777A Washer Genuine OEM Pulsator Cap – Compatible with Samsung Washers Product Description Keep your washer performing like new with the DC66-00777A Washer Genuine OEM Pulsator Cap. This factory-approved cap covers the central bolt on the pulsator (washplate), preventing water, detergent, and debris from entering the hub assembly. A missing or cracked cap can lead to corrosion, noise, or imbalance during spin cycles. Replacing it with this Genuine OEM part ensures a perfect fit, watertight seal, and long-lasting protection. Replaces Part Numbers DC66-00777A, PD00025125, EAP8753312, AP5788799, 3282678, PS8753312. Compatibility This Genuine OEM pulsator cap fits select Samsung top-load washers. Example compatible models include (but are not limited to): Samsung WA400PJHDWR/AA, WA422PRHDWR/AA, WA45H7000AW/A2, and WA50M7450AW/A4. Always verify your washer’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🧩 Genuine OEM Replacement – Factory-approved part ensures perfect fit and reliable performance 💧 Protective Design – Seals the washplate bolt area to prevent leaks and corrosion 🔇 Reduces Noise – Helps maintain balanced, quiet spin cycles 🛠️ Tool-Free Installation – Snaps securely into place in seconds 🛡️ Fixes Common Issues – Replaces missing, cracked, or leaking pulsator caps 📐 Product Specification Part Number: DC66-00777A Component Type: Washer Pulsator (Washplate) Cap Material: High-grade molded plastic Color: Silver or gray finish (varies by model) Mounting: Snap-fit installation over pulsator bolt Compliance: Genuine OEM certified 🛠️ Installation Notes Tools Needed: None ⚠️ Safety First: Always unplug the washer before performing any maintenance to prevent electrical shock. Steps: Open the washer lid and locate the pulsator (washplate) center. Remove any old or damaged cap remnants. Align the new DC66-00777A cap with the bolt opening. Press firmly until it clicks securely into place. Close the lid and test the washer. ⏱️ Time Required: Less than 5 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Genuine OEM Replacement Part 🔄 30-Day Return Policy Protect your washer from moisture and debris — Add to Cart Now for a perfect, factory-quality fit!

Read more less

W11670519 Genuine OEM Whirlpool Washer Lid Lock Latch Assembly The W11670519 is a genuine Whirlpool OEM lid lock latch assembly for Maytag top-load washers on the Cabrio-style MVW platform. Unlike a simple mechanical lid switch, this is a true electronic lid lock: a 3-wire connector feeds the assembly, which both senses whether the lid is closed and physically locks it shut once a cycle with spin is underway. The control won't allow the washer to spin — and on many cycles won't even let it start — until this assembly confirms the lid is closed and locked, which is why a failing latch produces such a wide range of symptoms: a washer that won't start, a lid that won't lock or won't release, cycles that stall or interrupt partway through, or a washer that fills and agitates but refuses to spin. Built from high-strength, wear-resistant ABS and PP plastic with a precision locking mechanism, this assembly is designed to prevent the lid from popping open mid-spin, which protects against water leakage and the safety hazard of an open lid on a spinning basket. Common failure modes include a locking mechanism that has worn out and can no longer engage or release reliably, a broken internal switch that stops signaling lid status to the control board, and simple wear from years of daily cycling. It directly replaces W11368616, AP7214714, PD00085482, 4981394, PS17215992, and EAP17215992. As a genuine OEM part, the W11670519 is manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. Quick Answer The W11670519 Genuine OEM Whirlpool Washer Lid Lock Latch Assembly fixes Maytag top-load washers on the Cabrio-style MVW platform where the washer won't start, the lid won't lock or won't release, the washer fills and agitates but won't spin, the cycle stalls or interrupts, or the lid clicks repeatedly without locking. 3-wire electronic lid lock, ABS/PP construction. Replaces W11368616, AP7214714, PD00085482, 4981394, PS17215992, EAP17215992. This is a locking latch assembly, not a simple lid switch — it's a different design from the direct-drive and GE-platform lid switches elsewhere in our catalog. Common Problems This Part Fixes Washer won't start even though the lid is closed Lid won't lock, or locks but won't release when the cycle ends Washer fills and agitates normally but won't spin Persistent clicking sound from the lid area without the lid actually locking Cycle stalling or interrupting partway through Lid feels loose or doesn't seat and lock the way it used to Error code related to the lid lock displayed on the control panel Water leakage risk from a lid that isn't sealing and locking properly during spin Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer lid lock latch assembly directly replaces the following OEM and cross-reference part numbers: W11670519, W11368616, AP7214714, AWP46151, PD00085482, 4981394, PS17215992, EAP17215992 W11368616 was an earlier number for this same assembly. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This lid lock latch assembly is compatible with select Maytag top-load washers on the Cabrio-style MVW platform, including model numbers such as: MVW4505MW0, MVW4505MW1, MVW4505MW2 MVW5035MW1, MVW5035MW2 MVW5430MW1, MVW5430MW2, MVW5430PBK0, MVW5430PBK1 MVW5435PBK0, MVW5435PBK1, MVW5435PW0, MVW5435PW1 Note: This is an electronic locking latch assembly for the Maytag Cabrio-style MVW platform, and it is a different design from the simpler lid switches used on other Whirlpool platforms — including our 8318084 (direct-drive top-load), 3355806 (Whirlpool thin-twin), WH12X955 (GE combo/spacemaker), and WH01X29528 (GE front-load door lock) listings. None of those are interchangeable with this assembly. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which lid lock or switch your washer needs. Key Features Genuine Whirlpool OEM part — factory-specified locking mechanism and switch design Electronic lid lock — both senses lid position and physically locks the lid during spin cycles Resolves "won't start," "lid won't lock or release," "fills but won't spin," and "cycle interruptions" symptoms caused by latch failure 3-wire connector for a direct plug-and-play electrical connection Constructed from high-strength ABS and PP plastic for wear and aging resistance Precision-designed locking mechanism helps prevent accidental lid opening during spin Direct drop-in replacement — no modification required Replaces W11368616, AP7214714, PD00085482, 4981394, PS17215992, and EAP17215992 Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number W11670519 Part Type Washer Lid Lock Latch Assembly Condition Genuine OEM Brand Whirlpool / Maytag Application Maytag Cabrio-Style Top-Load Washers (MVW Platform) Electrical Connection 3-wire connector Material High-strength ABS and PP plastic Function Senses lid closure and physically locks the lid during spin Supersedes W11368616 Quantity 1 lid lock assembly Compatible Brands Whirlpool, Maytag Installation Notes ⚠️ Unplug Washer Before Starting — If The Lid Is Locked Shut, Release It Manually First Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. If the old latch has failed in the locked position and you can't open the lid, insert a small flathead screwdriver into the latch opening where the lock mechanism engages through the lid, and gently slide the mechanism back to release it — then prop the lid open so it can't re-close and re-lock while you work. Remove the two screws holding the top section (control panel, lid, and wash basket opening) and slide the top of the unit forward and up to remove it, then prop it securely (a sturdy support between the cabinet frame and the top panel works well) rather than relying on your hands to hold it up. With the top propped open, remove the plastic cowl that the lid latch sits inside, which also retains the lock mechanism. Unclip the wiring harness from the retaining clips running around the inside of the lid and let the assembly hang free. Photograph the wiring connections before disconnecting the 3-wire connector from the old assembly. At the back of the lid, two metal spring clips retain the mechanism — squeeze these with your fingers or a set of pliers to release the old assembly, then pop the new W11670519 into place the same way. Reconnect the 3-wire connector, reclip the wiring harness into its retaining clips, and reinstall the plastic cowl. Lower the top panel back into position, reinstall its retaining screws, and confirm the lid closes, latches, and locks correctly through a full test cycle including spin. Tools needed: small flathead screwdriver, Phillips screwdriver, pliers, a sturdy prop for the top panel, work gloves. Frequently Asked Questions My washer fills and agitates but won't spin. Is this the lid lock? Yes, this is one of the most common symptoms of a failing lid lock latch on this platform. The control requires confirmation that the lid is closed and locked before it will allow the higher-speed, higher-torque spin cycle to run, even if it's willing to run the gentler fill and agitate steps without full confirmation. If your washer gets partway through a cycle and simply refuses to spin, this assembly is a strong suspect. The lid keeps clicking but never actually locks. What does that mean? A repeated clicking sound without the lid actually locking usually points to a worn or failing internal locking mechanism inside this assembly — it's attempting to engage but can't complete the lock reliably. This is a textbook symptom that this part has worn out and needs replacement. My washer's lid is locked shut and won't open. How do I even get it open to do this repair? With the washer unplugged, you can usually manually release the lock: insert a small flathead screwdriver into the latch opening where the mechanism engages through the lid, and gently slide it back to disengage the lock. Once the lid is open, prop it so it can't fall shut and re-lock while you continue the repair. Is this the same part as the lid switches used on other Whirlpool washers? No. This is an electronic locking latch assembly specific to the Maytag Cabrio-style MVW platform, and it works differently from the simpler mechanical lid switches used on other Whirlpool-family platforms, including the direct-drive top-load switch, the Whirlpool thin-twin switch, and various GE-platform switches we also carry. These parts are not interchangeable with each other — always match the assembly to your specific washer platform. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It includes the same 3-wire electrical connection, locking mechanism, and ABS/PP construction as the lid lock latch assembly originally installed in your Maytag Cabrio-style washer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

DC34-00025G Washer Genuine OEM Lid Switch and Lock Assembly – Fits Samsung Washers Product Overview The DC34-00025G Washer Lid Switch and Lock Assembly is a genuine OEM replacement part that ensures your washer lid stays securely locked during wash and spin cycles. This part detects when the lid is closed and locks it to prevent accidental opening, providing safety and proper cycle operation. A worn or broken lid lock can cause your washer to stop mid-cycle, display error codes, or fail to start. Replacing it restores dependable washer performance and safety compliance. Replaces Part Numbers This lid switch and lock assembly replaces DC34-00025G, AP6884125, PS12720530. Manufactured to original equipment specifications for a precise fit and long-term durability. Compatible Brands Compatible with select Samsung top-load washers manufactured by Samsung. Fits a variety of models using this specific lid lock assembly. Fixes the Following Issues Washer won’t start or stops mid-cycle Lid doesn’t lock properly Error codes related to lid switch or lock failure Washer won't enter spin or drain cycles Why Buy from Parts‑O‑Matic Factory-original genuine OEM part Fast and free U.S. shipping Trusted by appliance professionals and DIYers Backed by reliable customer support

Read more less

W10775188 Washer Genuine OEM Washplate Replaces Part Numbers: W10775188, 4282681, W10698538, W10834891, AP5959417, PS11699797. W10775188 Washer Washplate – Genuine OEM Part Restore optimal cleaning power with the W10775188 Washer Washplate. This Genuine OEM part replaces a worn or damaged washplate to ensure efficient agitation and even cleaning performance. Key Features: ✅ Genuine OEM Part – built to factory specs 🔁 Replaces: 4282681, W10698538, W10834891, AP5959417, PS11699797 🌀 Provides powerful agitation for deep cleaning 🛠️ Fits select Whirlpool, Maytag, and Amana top-load washers 🧰 Easy to install – includes center bolt ⚠️ Always unplug your washer before servicing. Need help with compatibility? Contact us! 📦 Part Number: W10775188

Read more less

XPARTCO 8181651 Washer Door Striker  Replaces Part Numbers: WP8181651, 8181651, 906446, AP6011711, PS11744910. Description: This Door Strike is a replacement part for specific Maytag, Kenmore, Whirlpool washing machine models. This component is responsible for providing a secure and proper closure for the washer door, ensuring it seals tightly during operation. This is an aftermarket part that can be used as a replacement for the OEM part. 

Read more less

285751 Washer Genuine Agitator Dog Cam Kit Replaces Part Numbers:  285751, 2837, 3351019, 387092, 3947410, AH334624, EA334624, OEM9283568, AP3094521, PS334624. Description: This Agitator Kit is an OEM replacement part for specific Whirlpool top-loading washer models. Installed in the center of the wash basket, it aids in the mechanical agitation central to regular laundry cleaning.It contains the plastic cam and four plastic dogs needed to repair a malfunctioning or noisy agitator during the wash cycle.   California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

WH10X29537 Front Load Washer Door Fits specific GE Washer models. Description: This Washer Door is a Genuine OEM replacement part for GE washing machines. It is the main access point to the washer drum, allowing you to load and unload your laundry with a secure and tight seal during operation. 

Read more less

DC31-20014C Washer Genuine OEM Shift Actuator This clutch (part number DC31-20014C) is for washers. Clutch DC31-20014C spins the basket during the spin cycle. Fits specific Samsung washer Models Replaces Part Numbers:DC31-20014C, 2068406, AP4211210, PS4204941.   California Residents only: WARNING: California’s Proposition 65

Read more less