Washer Parts

XPARTCO W10528947 Washer Drive Hub Kit The XPARTCO W10528947 is an aftermarket replacement washer basket drive hub kit compatible with select top-load washing machines from Whirlpool, Maytag, Kenmore, Amana, Admiral, Crosley, and Inglis. The drive hub is a critical transmission component that connects the spin basket to the spin shaft, transferring power from the motor to rotate the wash basket and agitate laundry during each cycle. This kit includes one basket drive hub and one drive block retainer — everything needed to restore proper spinning and agitation function. Common causes of drive hub failure include normal wear over time, strain from heavy or unbalanced loads, and physical damage from impact. A worn or cracked hub typically results in the basket slipping, failing to spin, or producing loud clicking and grinding noises during operation. Quick Answer The XPARTCO W10528947 Washer Drive Hub Kit fixes washers that won't spin, spin weakly, make clicking or grinding noises, or leave clothes too wet after the cycle. It connects the spin basket to the spin shaft and is compatible with select Whirlpool, Maytag, Kenmore, Amana, Admiral, Crosley, and Inglis top-load washers. Common Problems This Part Fixes Washer not spinning or agitating at all Weak or slow spin — clothes coming out too wet Clicking, grinding, or loud noises during spin cycle Basket slipping under load Washer pumping but not spinning Excessive shaking or movement during operation Replaces Part Numbers This kit directly replaces the following OEM and cross-reference part numbers: W10528947, 2684908, W10396887, W10528947VP, W11771931, EAP6012095, AWP40580, PD00024946, AP5665171, PS6012095. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drive hub kit is compatible with select top-load washers from the following brands: Whirlpool top-load washers Maytag top-load washers (including Bravos series) Kenmore top-load washers (select models) Amana top-load washers Admiral top-load washers Crosley top-load washers Inglis top-load washers Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Connects the spin basket to the spin shaft — restoring proper agitation and spin performance Aftermarket replacement built to OEM-equivalent quality standards Kit includes one basket drive hub and one drive block retainer for a complete repair Made from durable plastic construction designed to withstand regular wash cycle stress DIY-friendly repair — installs with basic hand tools in 30–60 minutes Budget-friendly alternative to OEM at a lower cost without sacrificing performance Product Specifications Part Number W10528947 Part Type Washer Basket Drive Hub Kit Condition Aftermarket Replacement Application Top-Load Washing Machine Material Durable Plastic (ABS) Hub Dimensions 3-5/8" Diameter x 13/16" H Retainer Clip Length 2-7/8" Kit Includes 1 Basket Drive Hub + 1 Drive Block Retainer Compatible Brands Whirlpool, Maytag, Kenmore, Amana, Admiral, Crosley, Inglis Installation Notes ⚠️ Safety First — Disconnect Power and Water Before Starting Unplug the washer from the power source and shut off the hot and cold water supply valves before beginning any repair. Remove the agitator or impeller (depending on your model) to access the drive hub. Unscrew the old hub and retainer, install the new drive hub kit in the same position, and reassemble the washer. Tools needed: multi-bit screwdriver, 7/16-inch socket with extension, and a nut driver. Allow 30–60 minutes for a complete repair. Consult your washer's service manual for model-specific instructions. Frequently Asked Questions Will the W10528947 fit my washer? This kit is compatible with select top-load washers from Whirlpool, Maytag, Kenmore, Amana, Admiral, Crosley, and Inglis. Always verify your washer's model number before ordering. Contact our support team if you need help confirming compatibility. What does the drive hub do? The drive hub connects the spin basket to the spin shaft beneath the agitator. It transfers power from the motor to rotate the wash basket during the spin and agitation cycles. When the hub wears out or cracks, the basket can slip or stop spinning entirely. What are the signs that my drive hub needs replacement? Common signs include: the washer won't spin or agitate, the spin cycle is weak or slow, clothes come out too wet, or you hear clicking and grinding noises during operation. Excessive shaking or movement during the cycle can also indicate a worn hub. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is designed to deliver reliable, long-lasting performance at a more affordable price point. What is included in the kit? The kit includes one basket drive hub and one drive block retainer — the two components needed for a complete drive hub replacement. Shop With Confidence Parts-O-Matic is a U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock parts for major appliance brands and ship quickly from our U.S. warehouse. Our team is available to help you verify compatibility before you buy. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

XPARTCO W10006355 Washer Shift Actuator  Fits specific Maytag, Kenmore, Whirlpool top-load machine models. Replaces Part Numbers: WPW10006355, W10006355, AP6014711, PS11747977. Description: This Shift Actuator is a replacement part for specific Maytag, Kenmore, Whirlpool washing machine models. It is an electronic component located inside the transmission that controls the shifting between wash cycles. The shift actuator receives signals from the washer control board to change modes, initiating proper movements to advance the cycle.   This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

XPARTCO 5221ER1003A Washer Water Inlet Valve Three solenoids. Washer cold water inlet valve assembly. 120V AC Washer cold water inlet valve assembly. Replaces Part Numbers: 5221ER1003A, 1268130, 5221ER1003C, 5221ER1003D, 5221ER1003F, AH3527452, EA3527452, AP4442608, PS3527452. 5220FR2075L, 4322702, AGM73269503, AP5986564, PS11728995. Description: This Water Inlet Valve Assembly is a replacement part for specific Kenmore, LG washing machine models. This critical component regulates the flow of water into the washing machine tub, ensuring the proper water supply for various wash cycles and functions.   This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

XPARTCO 8318084 Washer Lid Switch Replaces WP8318084 The XPARTCO 8318084 is an aftermarket replacement lid switch assembly compatible with a wide range of Whirlpool, Kenmore, KitchenAid, Roper, Estate, Maytag, Amana, Magic Chef, Crosley, and Admiral direct-drive top-load washing machines. The lid switch is a safety component located under the control panel at the top rear left corner of the washer — it detects whether the lid is open or closed and prevents the washer from spinning and agitating when the lid is open. When the lid is closed, the switch signals the control that it's safe to operate. Without a functioning lid switch, the washer may refuse to start, won't spin, won't agitate, won't drain, or stop advancing through its cycle. Gray and white plastic housing. Electrical rating: 125–250V, 50–60Hz, 1/2 HP. Dimensions: 3"L x 2"W x 1-15/16"H. Features 3 flat terminals that the wiring harness plugs onto, plus a green grounding wire. It directly replaces WP8318084, WP8318084VP, AP3180933, AP6012742, AH886960, EA886960, EAP11745957, ES8084, TJ90ES8084, PD00002474, PN8318084, PS886960, PS11745957, and 11480-61. This is one of the most widely used lid switches across the Whirlpool direct-drive platform, fitting hundreds of top-load washer models. Installs in 15–30 minutes with basic hand tools. Quick Answer The XPARTCO 8318084 Washer Lid Switch fixes Whirlpool, Kenmore, KitchenAid, Roper, Estate, Maytag, Amana, and Crosley direct-drive top-load washers that won't start, won't spin, won't agitate, won't drain, won't advance through the cycle, or have a burning smell from the motor. Gray/white, 125–250V, 50–60Hz, 1/2 HP. 3"L x 2"W x 1-15/16"H. 3 flat terminals + green grounding wire. Replaces WP8318084, WP8318084VP, AP3180933, AP6012742, AH886960, EA886960, EAP11745957, ES8084, TJ90ES8084, PD00002474, PN8318084, PS886960, PS11745957. Classic symptom: won't spin but may still fill. Common Problems This Part Fixes Washer won't spin — the classic lid switch failure symptom on direct-drive washers Washer won't start at all — control not detecting a closed lid Washer won't agitate — lid switch blocking motor engagement Washer won't drain — drain is tied to the spin/lid interlock on many models Wash cycle not advancing past fill — stuck waiting for lid-closed signal Burning smell from the motor area — motor stalling because the switch won't engage Lid won't close properly or switch doesn't activate when lid is shut Intermittent operation — washer sometimes works, sometimes doesn't, depending on lid position Lid switch visibly cracked, broken, or with a failed lever Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer lid switch directly replaces the following OEM and cross-reference part numbers: WP8318084, 8318084, WP8318084VP, ES8084, TJ90ES8084, 045903691979, 11480-61, PN8318084, AWP48129, EAP11745957, 11480-61, PN8318084, PD00002474, AP6012742, PS11745957. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This lid switch assembly is compatible with select direct-drive top-load washing machines from the following brands: Whirlpool top-load washers — direct-drive models (including 1CLBR, 1CLSQ, 1CLSR, LSQ, LSR, LSW, WTW series and many more) Kenmore and Kenmore Elite top-load washers (select Whirlpool-built models — 110-series) KitchenAid top-load washers (select models) Roper top-load washers (select models) Estate top-load washers (select models) Maytag top-load washers (select Whirlpool-built models) Amana top-load washers (select models) Magic Chef top-load washers (select models) Crosley top-load washers (select models) Admiral top-load washers (select models) Note: This lid switch is specific to direct-drive top-load washers on the Whirlpool platform. It is NOT the same switch used on stacked laundry centers, washer/dryer combos, or front-load washers — those use different lid switch or door lock part numbers. Always verify your appliance model number before ordering. Contact our support team with your model number if you're unsure. Key Features Direct-drive washer lid switch assembly — detects whether the lid is open or closed and prevents spinning, agitating, and draining when the lid is open Resolves "won't start," "won't spin," "won't agitate," "won't drain," "cycle not advancing," and "burning smell" symptoms caused by lid switch failure Gray and white plastic housing — durable construction Electrical rating: 125–250V, 50–60Hz, 1/2 HP Dimensions: 3"L x 2"W x 1-15/16"H 3 flat terminals that the wiring harness plugs onto, plus a green grounding wire Located under the control panel on the top rear left corner of the washer One of the most widely used lid switches on the Whirlpool direct-drive platform — fits hundreds of top-load washer models Replaces WP8318084, WP8318084VP, AP3180933, AP6012742, AH886960, EA886960, EAP11745957, ES8084, TJ90ES8084, PD00002474, PN8318084, PS886960, PS11745957, and 11480-61 Compatible with Whirlpool, Kenmore, KitchenAid, Roper, Estate, Maytag, Amana, Magic Chef, Crosley, and Admiral direct-drive top-load washers Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in 15–30 minutes with basic hand tools Product Specifications Part Number 8318084 OEM Part Number WP8318084 Part Type Washer Lid Switch Assembly (Direct-Drive Top-Load) Condition Aftermarket Replacement Application Direct-Drive Top-Load Washing Machines (Whirlpool platform) Voltage 125–250V Frequency 50–60 Hz Motor Rating 1/2 HP Dimensions 3"L x 2"W x 1-15/16"H Terminals 3 flat terminals + green grounding wire Color Gray / White Material Plastic housing Location Under the control panel, top rear left corner Compatible Brands Whirlpool, Kenmore, KitchenAid, Roper, Estate, Maytag, Amana, Magic Chef, Crosley, Admiral Installation Notes ⚠️ Unplug Washer Before Starting — Wear Work Gloves Disconnect power before beginning. Wear work gloves to protect your hands. The lid switch is located under the control panel at the top rear left corner of the washer. To access it, you'll need to remove the control panel: on most direct-drive washers, use a putty knife or flat-blade screwdriver to release the spring clips at the bottom edge of the control panel (typically two clips), then flip the control panel up and back on its hinges to rest against the wall behind the washer. You should now see the lid switch mounted on the left side with two screws. Photograph the wiring before disconnecting. Unplug the wiring harness from the 3 flat terminals on the old lid switch — note how the harness connects. Remove the two mounting screws holding the old switch in place. Also disconnect the green grounding wire (it's attached separately with its own screw). Remove the old switch. Install the new 8318084 switch in the same position using the two mounting screws. Reconnect the green grounding wire with its screw. Plug the wiring harness back onto the 3 flat terminals, matching your photos. Flip the control panel back down and press it into place until the spring clips snap. Plug the washer back in and test by closing the lid and running a cycle — confirm the washer starts, agitates, spins, and drains. Tools needed: Phillips screwdriver, putty knife or flat-blade screwdriver (for spring clips), work gloves. Frequently Asked Questions My washer won't spin but still fills — is the lid switch the problem? Very likely, yes. On direct-drive top-load washers, the lid switch is a safety interlock that prevents spinning and agitating when the lid is open. When the switch fails, the control never receives the "lid closed" signal, so it blocks the spin (and often the agitate and drain) as a safety measure — but filling still works because that doesn't require the lid interlock. If your washer fills but won't advance past that point, or agitates but refuses to spin, the lid switch is the prime suspect. You can confirm by testing the switch for continuity with a multimeter when the lever is pressed — a working switch shows continuity when activated. Why would a bad lid switch cause a burning smell? This happens when the motor tries to engage but the lid switch isn't signaling correctly, causing the motor to stall or repeatedly attempt to start without completing the cycle. A stalling direct-drive motor generates heat that produces a burning smell. If you notice a burning smell AND the washer isn't spinning or agitating properly, check the lid switch first — it's far more likely (and cheaper) than a motor failure. If the burning smell continues after replacing the switch, have the motor and motor coupling inspected by a technician. What's the difference between 8318084 and WP8318084? These are the same lid switch across production revisions. 8318084 was the original part number and WP8318084 is the Whirlpool-era part number (with the "WP" prefix Whirlpool adopted). WP8318084VP is a variant packaging code. All are physically and functionally identical — if your washer's parts diagram shows any of these numbers, this listing is the correct replacement. The many additional cross-references (AP3180933, AP6012742, ES8084, PS886960, PS11745957, etc.) are catalog identifiers from various parts distributors for the same switch. Does this fit my stacked laundry center or front-load washer? No — the 8318084 is specifically designed for standalone direct-drive top-load washers on the Whirlpool platform. Stacked washer/dryer laundry centers use different lid switch part numbers (such as the 3355806 for Whirlpool thin twin units), and front-load washers use door lock assemblies instead of lid switches. Always search by your appliance's model number to confirm the correct part. Contact our support team with your model number if you're unsure which switch fits your machine. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the electrical specifications (125–250V, 50–60Hz, 1/2 HP), dimensions (3"L x 2"W x 1-15/16"H), 3-flat-terminal configuration, grounding wire, and lid-detection function of the original WP8318084 lid switch used in compatible Whirlpool, Kenmore, KitchenAid, Roper, Estate, Maytag, Amana, and related direct-drive top-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO W10913953 Washer Shift Actuator The XPARTCO W10913953 is an aftermarket replacement washer shift actuator assembly compatible with select Whirlpool, Maytag, Kenmore, Amana, Crosley, Inglis, and Roper top-load washers with VM (variable motor) transmissions — including Whirlpool Cabrio, Maytag Centennial, and Maytag Bravos series. The shift actuator is a small synchronous gearmotor assembly located beneath the washer tub that controls how the transmission shifts between agitation mode and spin mode during the wash cycle. It moves the arm on the cam ring assembly to engage the basket (for spinning) or disengage it and engage only the agitator or wash plate (for agitation). The shift actuator also contains an internal tachometer that continuously reports the basket's rotational speed to the control board. When the shift actuator fails — most commonly due to a stripped or broken gear inside the gearmotor — the washer may not agitate, not spin, get stuck in one phase of the cycle, display error codes F7E1 or F7E5, or produce a loud grinding or clicking noise as the gears fail. This 6-pin plug assembly is rated 120V, 60Hz, 4W with a synchronous motor running at 3 RPM clockwise rotation. It measures 4-1/4"L x 2-3/4"W x 1-7/8"H and directly replaces W10815026, W10597177, WPW10597177, 4455082, 49TYZ-E120A1, 50SM21-1-221B, AP6037270, and PS11769864. Installs in 20–30 minutes with basic hand tools. Quick Answer The XPARTCO W10913953 Washer Shift Actuator fixes Whirlpool Cabrio, Maytag Centennial, and Maytag Bravos top-load washers that won't agitate, won't spin, display error codes F7E1 or F7E5, or make grinding/clicking noises when trying to shift cycles. 6-pin plug, 120V/60Hz/4W synchronous motor, 3 RPM CW, 4-1/4"L x 2-3/4"W x 1-7/8"H. Replaces W10815026, W10597177, WPW10597177, 4455082, 49TYZ-E120A1, AP6037270, PS11769864. Compatible with Whirlpool, Maytag, Kenmore, Amana, Crosley, Inglis, and Roper VM-transmission top-load washers. Common Problems This Part Fixes Washer not agitating — basket fills with water but agitator or wash plate does not move Washer not spinning — cycle advances to spin but basket does not rotate Washer getting stuck in one phase — completing wash or fill but not advancing to spin Clothes soaking wet after a full cycle — washer is not reaching high-speed spin Error codes F7E1 or F7E5 displayed — motor shift or basket speed sensing fault Loud grinding, clicking, or buzzing noise during cycle transitions between agitate and spin Washer pumping normally but basket not spinning after draining Replaces Part Numbers This shift actuator directly replaces the following OEM and cross-reference part numbers: W10913953, W10815026, 4455082, 49TYZ-E120A1, 50SM21-1-221B, KT-155867_rev011, EAP11769864, AP6037270, AWP42172, PD00032232, PS11769864. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This shift actuator is compatible with select top-load washers with VM transmissions from the following brands and series: Whirlpool top-load washers — Cabrio series (WTW5000, WTW4816, WTW4850, WTW4915, WTW4950, WTW4955 and related models) Maytag top-load washers — Centennial series (MVWC215, MVWC415, MVWC416, MVWC465, MVWC555, MVWC565 and related models) Maytag top-load washers — Bravos series (MVWX655 and related models) Kenmore / Sears top-load washers (select Whirlpool-built models) Amana top-load washers — NTW series (NTW4516, NTW4655 and related models) Crosley top-load washers (select models) Inglis top-load washers (select models) Roper top-load washers (select models) Note: The W10913953 is for VM (variable motor) transmission top-load washers. It is not compatible with older Whirlpool top-load washers using a different transmission type. Always verify your model number before ordering. The shift actuator works in conjunction with the pulley clutch kit (W10721967 / W10006384) — if the actuator is good but the issue persists, the clutch kit should also be inspected. Key Features Controls transmission shifting between agitation mode and spin mode during the wash cycle Moves the cam ring arm to engage the basket for spinning, or disengage it to allow only the agitator/wash plate to move Integrated tachometer — continuously reports basket rotational speed to the control board for cycle management Synchronous gearmotor — 120V, 60Hz, 4W, 3 RPM clockwise rotation 6-pin plug connector — direct plug-in installation on compatible models Dimensions: 4-1/4"L x 2-3/4"W x 1-7/8"H Resolves F7E1 and F7E5 error codes on compatible Whirlpool and Maytag top-load washers Replaces W10815026, W10597177, WPW10597177, 4455082, 49TYZ-E120A1, and AP6037270 Compatible with Whirlpool Cabrio, Maytag Centennial, Maytag Bravos, Amana NTW, and Kenmore VM-transmission top-load washers Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 20–30 minutes with basic hand tools Product Specifications Part Number W10913953 Also Replaces W10815026, W10597177 (prior versions) Part Type Washer Shift Actuator Assembly (Mode Shift Actuator) Condition Aftermarket Replacement Application Top-Load Washers with VM Transmission (Cabrio, Centennial, Bravos) Motor Type Synchronous gearmotor Voltage 120V AC Frequency 60 Hz Wattage 4W Speed 3 RPM, clockwise rotation Connector 6-pin plug Dimensions 4-1/4"L x 2-3/4"W x 1-7/8"H Includes Integrated tachometer for basket speed sensing Error Codes Resolved F7E1, F7E5 Compatible Brands Whirlpool, Maytag, Kenmore, Amana, Crosley, Inglis, Roper Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off the water supply before beginning. The shift actuator is located beneath the washer tub on the drive shaft assembly. To access it, remove the washer cabinet by unscrewing the top panel and releasing the front panel, or lay the washer on its back if your model requires it. The shift actuator is mounted to the bottom of the drive shaft assembly with mounting screws and connects to the washer's control harness via a 6-pin plug. Photograph the wiring before disconnecting. Remove the mounting screws, disconnect the 6-pin harness, and slide the old actuator off the shaft. Install the new W10913953 actuator in the same position and orientation, secure the mounting screws, and reconnect the 6-pin harness. Reassemble the cabinet, restore power and water, and run a test cycle through both agitation and spin to confirm normal operation. Note: if grinding noise continues after replacing the actuator, inspect the pulley clutch kit (W10721967 / W10006384) for wear. Tools needed: Phillips screwdriver, 1/4" nut driver, Torx screwdriver (T20 on some models). Frequently Asked Questions What does the shift actuator do in a top-load washer? The shift actuator is a small synchronous gearmotor that controls the transmission shifting in Whirlpool Cabrio, Maytag Centennial, and Bravos-style VM-transmission top-load washers. During a wash cycle, the control board signals the actuator to move the cam ring arm — this engages or disengages the drive connection between the motor and the basket. When the cam moves one way, only the agitator or wash plate moves (agitation mode). When it moves the other way, the basket engages and spins at high speed (spin mode). The actuator also contains a tachometer that tells the control board how fast the basket is rotating, which the board uses to manage spin speed and detect imbalance. What are error codes F7E1 and F7E5? On compatible Whirlpool Cabrio and Maytag Centennial/Bravos top-load washers, F7E1 indicates a motor shift error — the actuator failed to complete the shift between agitate and spin mode within the expected time. F7E5 indicates a basket speed sensing fault — the tachometer inside the actuator is not providing a valid speed signal to the control board. Both codes are commonly caused by a failed shift actuator, though a failed drive motor, clutch assembly, or control board can also produce these codes. Replacing the shift actuator resolves both error codes in most cases. Should I also check the pulley clutch kit? Yes — if the shift actuator is replaced but the grinding noise persists, or if the washer still does not agitate or spin properly after the new actuator is installed, inspect the pulley clutch kit (W10721967 / W10006384). The clutch kit is a separate assembly that works in conjunction with the shift actuator to engage the drum. A worn or stripped clutch can produce the same symptoms as a failed actuator and is a common companion failure. Since the washer is already disassembled to replace the actuator, it is a good opportunity to inspect the clutch for wear. What is the difference between W10913953 and W10815026? The W10815026 was an earlier version of this shift actuator, and the W10913953 is the updated current replacement. Both are the same functional component — Whirlpool updated the part number during a production revision. The W10597177 and WPW10597177 are also cross-references for this same actuator. If your washer's parts diagram shows any of these older numbers, the W10913953 is the correct current replacement to order. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured with a synchronous gearmotor and ABS housing to match the electrical specifications and dimensions of the original W10913953 shift actuator. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO WH12X955 Washer Lid Switch The XPARTCO WH12X955 is an aftermarket replacement lid switch assembly compatible with GE, Hotpoint, RCA, and Kenmore GE-built washer/dryer combo units (including GE spacemaker and stacked laundry models). The lid switch is a safety component mounted inside the washer lid — it detects whether the lid is open or closed and signals the control that it's safe for the machine to start, agitate, and spin. When the lid closes, the switch activates and the washer can run through its full cycle. If the lid switch fails, the washer typically won't spin or drain, may not start or agitate at all, and clothes are left sitting in water. This is a complete lid switch assembly with an integrated wiring harness and ground wire. Dimensions: 1-1/4" H x 2-1/4" W x 16" D (the 16" depth is the wire harness that routes from the lid down into the washer cabinet). It directly replaces WH12X955, WH12X0955, AP2045786, 278666, AH270219, EA270219, PS270219, and OEM6137363. Installation involves accessing the lid itself — the switch mounts inside the lid with two screws plus a separate ground wire screw. Installs in 30–45 minutes with basic hand tools. Quick Answer The XPARTCO WH12X955 Washer Lid Switch fixes GE, Hotpoint, RCA, and Kenmore GE-built washer/dryer combo units where the washer won't spin, won't drain, won't start, or won't agitate — leaving clothes sitting in water. Complete lid switch assembly with wiring harness and ground wire. Dimensions 1-1/4"H x 2-1/4"W x 16"D. Replaces WH12X0955, AP2045786, 278666, AH270219, EA270219, PS270219, OEM6137363. Classic symptom: washer won't spin or drain. Common Problems This Part Fixes Washer won't spin — the classic lid switch failure symptom Washer won't drain — clothes left sitting in water at the end of the cycle Washer won't start at all — control not detecting a closed lid Washer won't agitate — the machine won't advance past the fill phase Machine doesn't recognize the lid is closed even when it is Lid switch body cracked from the lid being closed hard over time Internal switch contacts worn out — no longer signaling that the lid is closed Intermittent operation — washer sometimes spins, sometimes doesn't, depending on lid position Broken or frayed lid switch wiring harness Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer lid switch directly replaces the following OEM and cross-reference part numbers: WH12X955, 278666, AGE25981, AH270219, EA270219, PD00030733, EAP270219, PS270219, AP2045786, WH12X0955, EXPWH12X955 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This lid switch assembly is compatible with select washer/dryer combo units (spacemaker and stacked laundry models) from the following brands: GE washer/dryer combo units — spacemaker and stacked laundry center models GE Spacemaker washers — select models Hotpoint washer/dryer combo units (select GE-built models) RCA washer/dryer combo units (select GE-built models) Kenmore / Sears washer/dryer combo units (select GE-built models) Note: This lid switch is specific to GE washer/dryer combo and spacemaker units — it is NOT the same switch used on standalone GE top-load washers, which use different lid switch part numbers. Always search by your appliance model number to confirm this part fits before ordering. Contact our support team with your model number if you're unsure. Key Features Lid switch safety assembly — detects whether the lid is open or closed and allows the washer to start, agitate, spin, and drain when the lid is shut Resolves the classic "won't spin" and "won't drain" symptoms of lid switch failure Complete assembly with integrated wiring harness and ground wire Dimensions: 1-1/4" H x 2-1/4" W x 16" D (the 16" depth is the wiring harness) Mounts inside the washer lid with two screws plus a separate ground wire screw Snap-in switch design with connector — no wiring modifications required Replaces WH12X0955, AP2045786, 278666, AH270219, EA270219, PS270219, and OEM6137363 Compatible with GE, Hotpoint, RCA, and Kenmore GE-built washer/dryer combo and spacemaker units Aftermarket replacement built to OEM-equivalent quality standards DIY-friendly repair — installs in 30–45 minutes with basic hand tools Product Specifications Part Number WH12X955 Part Type Washer Lid Switch Assembly Condition Aftermarket Replacement Application Washer/Dryer Combo & Spacemaker Units (GE platform) Dimensions 1-1/4" H x 2-1/4" W x 16" D Includes Lid switch, wiring harness, ground wire Function Prevents washer spin/agitation when lid is open Location Inside the washer lid Mounting Two screws + separate ground wire screw Compatible Brands GE, Hotpoint, RCA, Kenmore (GE-built) Installation Notes ⚠️ Unplug Washer Before Starting — Wear Work Gloves — The Lid Comes Off Disconnect power at the outlet or breaker before beginning. Wear work gloves to protect your hands from sharp sheet metal edges. This repair requires removing the washer lid to access the switch. Open the lid, then push it toward the back of the machine to release the plastic clips at the front that hold the lid up. Slowly lift the lid at the front — you'll see the lid switch is the only thing still connecting the lid to the washer body. Confirm the power is off, then unclip the electrical connector that joins the lid switch harness to the washer's wiring (it's typically a molex-style connector). With the connector released, you can carry the lid to a workbench or flat surface to work on it comfortably. On the underside/inside of the lid, remove the two screws on the right-hand side that hold the switch in place, then remove the screw that secures the ground wire to the inside of the lid. Lift out the old switch. The new WH12X955 switch snaps into place — seat it, reinstall the two mounting screws, and reattach the ground wire with its screw. Route the new harness cable through the same path as the old one; you can gently lift the retaining clips with a flathead screwdriver to slide the new cable through. Reconnect the electrical connector, set the lid back into position, and press it down until the front plastic clips engage. Restore power and test by closing the lid and running a cycle — confirm the washer agitates, drains, and spins. Tools needed: Phillips screwdriver, nut driver, flathead screwdriver, work gloves. (Tip: if you drop the ground wire nut inside the cabinet, a magnet on a stick makes retrieval easy.) Frequently Asked Questions My washer won't spin or drain — is the lid switch the cause? Yes — this is the single most common and telling symptom of a failed lid switch. The lid switch is a safety interlock that prevents the drum from spinning while the lid is open. When the switch fails (cracked body, worn internal contacts, or broken wiring), the control never receives the "lid closed" signal, so it blocks the spin and drain phases as a safety measure — leaving your clothes sitting in water. On many GE washer/dryer combos, a failed lid switch will also prevent the machine from starting or agitating at all. If your washer fills but goes no further, or completes the wash but leaves clothes soaked, the lid switch is the prime suspect. You can confirm by testing the switch for continuity with a multimeter when the lever is depressed. Why is this switch 16" long? The 16" dimension is the length of the wiring harness, not the switch body itself. The switch mounts inside the washer lid, and its harness has to route from the lid, through the hinge area, down into the washer cabinet to reach the main wiring connector. That's why the assembly comes with a long attached cable — and it's also why this repair involves removing the lid to access everything. The switch body itself is compact at roughly 1-1/4" H x 2-1/4" W. Does this fit my standalone GE top-load washer? Probably not. The WH12X955 is specifically used on GE washer/dryer combo units and spacemaker/stacked laundry models. Standalone GE top-load washers use different lid switch part numbers. Because the lid switch design and mounting vary significantly across GE's washer lineup, always search by your appliance model number to confirm the correct part before ordering. If your unit is a standalone top-loader, contact our support team with your model number and we'll identify the right lid switch for it. Do I really have to take the lid off to install this? On most compatible models, yes — the lid switch mounts inside the lid itself, so you'll need to release the lid from the washer body to reach the two mounting screws and the ground wire screw. The good news is that the lid comes off fairly easily: push it toward the back to release the front plastic clips, then lift it slowly, unclip the electrical connector, and carry the lid to a comfortable work surface. Working on the lid off the machine is far easier than trying to reach into a cramped laundry closet. Just be sure power is disconnected before unclipping the connector. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured to match the dimensions (1-1/4"H x 2-1/4"W x 16"D), harness and ground wire configuration, connector, mounting, and lid-detection function of the original WH12X955 lid switch used in compatible GE, Hotpoint, RCA, and Kenmore GE-built washer/dryer combo and spacemaker units. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

DC97-15459G Washer Water Valve 120V, 60Hz, five coil linear valve. Fits Specific Samsung Washer Models. Replaces Part Numbers:DC97-15459G, AP5623056, PS4220861. Description: The Water Valve Assembly is a replacement part for specific Samsung washing machines. It controls the flow of hot and cold water into the washer during the different cycles, ensuring the proper mix and temperature for effective cleaning.  The water valve assembly can fail due to various reasons such as mineral deposits from hard water clogging the valve, electrical issues, or general wear and tear over time. Exposure to high water pressure or impurities in the water supply can also lead to malfunction.   This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

XPARTCO W11168740 Washer Water Valve (Cold Side) – Compatible with Whirlpool, Maytag, Amana, Kenmore, and Crosley Washers Product Description Restore proper cold-water filling to your washer with the XPARTCO W11168740 Washer Water Valve (Cold Side). This Water Inlet Valve is a replacement part for specific Kenmore, Maytag, Whirlpool washing machine models. It controls the flow of water into the washer tub at designated stages in the washing process. Water enters through the valve inlet and is distributed to internal components like the detergent dispenser, water pipes, and sump hoses. Common causes of a bad valve can include mineral scale buildup inhibiting proper flow regulation over time, or cracks and leaks from wear and tear on rubber gaskets and seals.  Replaces Part Numbers W11168740, WPW10240949, W10240949, W10921514, 33390069, PD00038781, EAP12348073, AP6285450, PS12348073. Compatibility This replacement cold-side water valve fits select Whirlpool, Maytag, Amana, Kenmore, Crosley, and Estate washers. Example compatible models include (but are not limited to):Whirlpool WTW5000DW1, Maytag MVWC465HW2, Amana NTW4516FW3, Kenmore 110.25132411. Always verify your washer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Engineered to match OEM water flow and pressure performance ❄️ Cold-Water Control – Regulates cold-water intake for proper wash temperatures 💰 Budget-Friendly Option – Reliable performance at a lower cost than OEM valves 🛠️ Durable Solenoid Design – Ensures strong, consistent water flow 🛡️ Fixes Common Issues – Solves slow filling, no cold-water fill, temperature errors, or cycle interruptions 📐 Product Specification Part Number: W11168740 Component Type: Washer Water Inlet Valve (Cold Side) Material: Reinforced plastic body with metal solenoid Ports: Single cold-water inlet Mounting: Direct-fit installation on rear washer panel Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, pliers, towel or bucket ⚠️ Safety First: Unplug the washer and turn off water supply before installation. Steps: Disconnect power and shut off water to the washer. Remove the rear access panel to expose the inlet valve. Disconnect the cold-water hose and electrical connector. Remove the mounting screws and take out the old valve. Install the new XPARTCO W11168740 valve and reconnect wiring and hose. Turn water back on, restore power, and test for leaks and proper filling. ⏱️ Time Required: 10–20 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Restore dependable cold-water filling — Add to Cart Now for a reliable, cost-effective repair!

Read more less

XPARTCO WH01X29528 Washer Door Lock The XPARTCO WH01X29528 is an aftermarket replacement door lock assembly compatible with a wide range of GE, GE Profile, Café, Haier, Hotpoint, RCA, and Monogram front-load washing machines — as well as select GE UltraFast 2-in-1 combo washer/dryer units. The door lock is a safety mechanism mounted at the front of the washer where the door closes — it automatically engages when the door is shut, securing it closed for the entire wash and spin cycle so water and detergent can't spill out and cause injury. It also signals the control board that the door is safely locked, which is what allows the washer to start filling and running. When the door lock fails, the washer typically won't start, won't lock the door, stops mid-cycle, or throws a door-related error code. Rated 120 VAC, 60Hz, 16A. Failure usually comes from physical damage or normal wear over time. As a direct replacement for the GE WH01X29528, it also replaces AP6985313, EAP12749276, PS12749276, PD00060769, and 4958749 (additional production markings: ITW 12070-71, V13305, 0024000128GE). Installation is straightforward with no wiring modifications — remove the old lock and install the new one, typically in 10–15 minutes with basic hand tools. Quick Answer The XPARTCO WH01X29528 Washer Door Lock fixes GE, GE Profile, Café, and Haier front-load washers (and GE UltraFast 2-in-1 combo units) where the door won't lock or unlock, the washer won't start, the washer stops mid-cycle, the door feels loose or won't seal, or a door-latch error code appears. 120 VAC, 60Hz, 16A. Replaces AP6985313, EAP12749276, PS12749276, PD00060769, 4958749. Compatible with GE GFW510, GFW550, GFW650, GFW850, PFW870, PFW950, PFQ97 series front-load washers. No wiring modifications — installs in 10–15 minutes. Common Problems This Part Fixes Washer door won't lock at the start of the cycle Washer won't start — control board not detecting a locked door Washer door won't unlock at the end of the cycle Washer stops mid-cycle due to a door lock fault Door-latch related error code displayed on the control panel Door feels loose or doesn't seal properly Excessive noise and shaking while the washer is running (related to a door not securing properly) Intermittent locking — washer sometimes starts, sometimes doesn't Door lock assembly visibly broken, cracked, or with a failed latch Burning/electrical smell or humming from the door lock area (failed lock solenoid) Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer door lock directly replaces the following OEM and cross-reference part numbers: WH01X29528, 4958749, AGE26402, AP6985313, PS12749276, EAP12749276, PD00060769, ITW 12070-71, OEM20955948, V13305, 0024000128GE If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This door lock assembly is compatible with select front-load washing machines and combo washer/dryer units from the following brands: GE front-load washers — GFW510 series (GFW510SCN0WW–SCN5WW, GFW510SCV0WW) GE front-load washers — GFW550 series (GFW550SPN0DG–SPN3DG, GFW550SPR0RS/SPR3RS/SPR4RS/SPR5RS, GFW550SSN0WW–SSN5WW) GE front-load washers — GFW650 series (GFW650SPN0SN–SPN4SN, GFW650SSN0WW–SSN4WW) GE front-load washers — GFW655 series (GFW655SPV0DS, GFW655SSV0WW) GE front-load washers — GFW850 series (GFW850SPN0DG–SPN5RS all DG/RS variants, GFW850SSN0WW–SSN5WW) GE Profile front-load washers — PFW870 series (PFW870SPV0RS, PFW870SSV0WW), PFW950 series (PFW950SPT0DS/SPT1DS/SPT2DS) GE Profile combo units — PFQ97HSPV0DS (UltraFast 2-in-1 combo washer/dryer) GE Café, Haier, Hotpoint, RCA, Monogram — select front-load models using the same door lock Sears Kenmore and Crosley — select GE-built front-load models Always verify your appliance model number before ordering. The WH01X29528 fits the specific models listed — please double-check your model number. Contact our support team if you're unsure. Key Features Door lock and switch assembly — locks the washer door during the wash and spin cycles and signals the control board that the door is safely closed Prevents the door from being opened mid-cycle, keeping water and detergent safely contained Resolves "won't lock," "won't unlock," "won't start," "stops mid-cycle," and door-latch error codes when caused by a failed lock Rated 120 VAC, 60Hz, 16A — correct electrical specifications for compatible GE front-load washers Integrates with the washer's main control board, door switch, and load detection system Durable, moisture-resistant materials resist deformation, wear, and short circuits for long service life No wiring modifications required — direct-fit replacement using the original connector Replaces AP6985313, EAP12749276, PS12749276, PD00060769, and 4958749 Compatible with GE GFW510/GFW550/GFW650/GFW850, PFW870/PFW950, and PFQ97 series front-load washers and UltraFast combo units, plus select Café, Haier, Hotpoint, RCA, Monogram, Kenmore, and Crosley GE-built models Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in 10–15 minutes with basic hand tools Product Specifications Part Number XPWH01X29528 Part Type Washer Door Lock and Switch Assembly Condition Aftermarket Replacement Application Front-Load Washers & Combo Washer/Dryer Units (GE platform) Voltage 120 VAC Frequency 60 Hz Amperage 16A Additional Production Markings ITW 12070-71, V13305, 0024000128GE Function Locks door during wash/spin; signals control board door is secure Location Front of washer at the door opening Compatible Brands GE, GE Profile, Café, Haier, Hotpoint, RCA, Monogram, Kenmore, Crosley Installation Notes ⚠️ Unplug Washer Before Starting — Wear Work Gloves Disconnect power before beginning. Wear work gloves to protect your hands. Open the washer door — if the door is stuck locked because of a failed lock, you may need to access the manual release. Peel back the rubber door boot/gasket from the front panel edge near the lock to expose the door lock assembly — on some models this requires releasing the spring-loaded wire clamp that secures the boot with needle-nose pliers. Photograph the wire harness connection before disconnecting anything. Remove the mounting screws holding the door lock assembly to the front panel. Reach in and pull the assembly out through the door opening far enough to access the wire connector. Disconnect the wire harness plug from the old assembly (no wiring modifications are needed — it's a direct plug connection). Snap the new WH01X29528 assembly onto the wire harness plug until it clicks firmly, position it in the front panel opening, and secure it with the mounting screws. Press the rubber door boot back into its groove and reinstall the spring-loaded wire clamp if applicable. Restore power and test by closing the door and starting a cycle — confirm the door locks, the washer runs, and the door unlocks at the end. Tools needed: Phillips screwdriver, needle-nose pliers, work gloves. Frequently Asked Questions My GE washer won't start and shows a door error — is this the part? Very likely, yes. GE front-load washers won't start unless the control board receives confirmation from the door lock that the door is closed and locked — it's a safety interlock. When the door lock fails, the washer either won't lock the door, won't start, or displays a door-related message on the panel. If your door appears to close normally but the washer won't begin the cycle (or stops shortly after starting), the door lock is the most common cause. Replacing the WH01X29528 typically resolves it. If you've already replaced the door lock and the problem persists, the issue may be the main control board instead. I replaced the door lock and it worked briefly, then failed again — what's wrong? If a new door lock works for a short time (seconds to minutes) and then the washer goes back to showing a door error, the problem may not be the lock itself but the main control board that powers and monitors it. A control board with a failing door-lock circuit can damage or fail to properly drive the lock, causing repeated symptoms even after replacing the lock. Some customers report an electrical smell or humming from the lock in these cases. If you've replaced the door lock (especially more than once) and the door error returns, the main control board is the next component to investigate. Contact our support team with your model number for the correct control board part. Does this fit the GE UltraFast 2-in-1 combo washer/dryer? Yes — the WH01X29528 is used on select GE UltraFast 2-in-1 combo washer/dryer units (such as the PFQ97HSPV0DS) in addition to standalone GE front-load washers. The combo units use the same door lock design as the front-load washers in the GFW/PFW families. As always, confirm your specific model number against the compatibility list before ordering, since GE uses different door locks across different washer generations. How do I open the door if it's stuck locked and the washer won't run? If the door is stuck in the locked position because of a failed lock, first make sure there's no water in the drum (run or complete a drain cycle if possible). Then unplug the washer and wait a few minutes — some GE models release the lock after power is removed. If it's still stuck, most front-load washers have a manual release mechanism accessible from behind the lower kick panel at the front of the machine — a tab or cord you pull to manually disengage the lock. Consult your model's manual for the manual release location. Once the door is open, you can proceed with replacing the lock. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine GE OEM part, but is manufactured from durable, moisture-resistant materials to match the electrical specifications (120 VAC, 60Hz, 16A), connector configuration, mounting, and door-locking function of the original WH01X29528 door lock used in compatible GE, GE Profile, Café, Haier, and related front-load washers and combo units. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO W11688995 Washer Water Inlet Valve (Cold) The XPARTCO W11688995 is an aftermarket replacement cold water inlet valve designed as a direct fit for select Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, Magic Chef, Admiral, Norge, Roper, Inglis, and Kenmore front-load washers. The cold water inlet valve is mounted at the back of the washer where the cold water supply hose connects. When the washer's control board calls for cold water during a wash cycle, the valve's internal solenoid opens, letting water flow into the tub or detergent dispenser. The valve closes the instant the control board cuts power, stopping flow precisely as the correct fill level is reached. When this valve fails, the washer may not fill with cold water at all, fill very slowly, fail to dispense fabric softener, continuously drip water into the tub even when off, or display F8E1 or LO FL error codes. Construction is blue and white plastic with metal solenoid coil, ~3"H x 4"W x 3"L, with 1/2" NPT threaded inlet for standard washer supply hose. It directly replaces W11688995, W11036930, W11316256, W11486361, AP7218603, EAP12711564, PD00086086, PS12711564, 4929298, and AP6835737. Often replaced as a pair with the hot water inlet valve (W11688994, sold separately). Installs in 10–15 minutes with basic hand tools. Quick Answer The XPARTCO W11688995 Washer Water Inlet Valve (Cold) fixes Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, and Kenmore front-load washers displaying F8E1 or LO FL error codes, not filling with cold water, filling slowly, failing to dispense fabric softener, or continuously dripping into the tub. Blue/white plastic with metal coil, 1/2" NPT thread, ~3"H x 4"W x 3"L. Replaces W11036930, W11316256, W11486361, AP7218603, EAP12711564, PD00086086, PS12711564, 4929298, AP6835737. Often paired with the hot water valve (W11688994, sold separately). Common Problems This Part Fixes Washer not filling with cold water — valve solenoid not opening when commanded Washer filling slowly with cold water — valve partially clogged or weak solenoid F8E1 error code displayed — cold water inlet valve fault LO FL (low flow) error code — valve unable to deliver normal water flow Fabric softener not being dispensed — cold water flush to dispenser failing Water continuously dripping into the tub when the washer is off — valve stuck open or not fully closing Water leaks at the valve body — internal seal failure Wash cycles taking much longer than normal due to slow fill Replaces Part Numbers This cold water inlet valve directly replaces the following OEM and cross-reference part numbers: W11688995, W11316256, W11036930, W11486361, 4983050, PD00086086, FIX17216730, EAP17216730, OEM28874414, AP7218603, AWP46809, PS17216730. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This cold water inlet valve is compatible with select front-load washers from the following brands: Whirlpool front-load washers — WFC6810LW0, WFC9820HC0, WFC9820HW0 series Whirlpool front-load washers — WFW560CHW0, WFW560CHW1, WFW560CHW2, WFW560CHW3, WFW560CHW4 series Whirlpool front-load washers — WFW5605MC0, WFW5605MW0 series Whirlpool front-load washers — WFW5620HW0, WFW5620HW1, WFW5620HW2, WFW5620HW3 series Whirlpool front-load washers — WFW6620HC0, WFW6620HC1, WFW6620HC2, WFW6620HW0, WFW6620HW1 series Whirlpool front-load washers — WFW8620HC0, WFW8620HC1, WFW8620HC2, WFW8620HC3, WFW8620HC4, WFW8620HW0, WFW8620HW1, WFW8620HW2, WFW8620HW3, WFW8620HW4 series Whirlpool front-load washers — WFW862CHC0, WFW862CHC1, WFW862CHC2, WFW862CHC3 series Whirlpool front-load washers — WFW9620HBK1, WFW9620HBK2, WFW9620HBK3, WFW9620HC0, WFW9620HC1, WFW9620HC3, WFW9620HW0, WFW9620HW1, WFW9620HW2, WFW9620HW3 series Maytag front-load washers — MHW5630HC0, MHW5630HW1, MHW5630MBK0 series and related Amana front-load washers — NFW5800HW0, NFW5800HW1 and related models Inglis front-load washers — IFW5900HW, IFW5900HW1 and related models KitchenAid, Jenn-Air, Magic Chef, Admiral, Norge, Roper front-load washers — select Whirlpool-built models Kenmore / Sears front-load washers — select Whirlpool-built models Note: This is the cold water inlet valve (typically blue). The matching hot water inlet valve is part number W11688994 (typically red). When you replace one valve, it's a good practice to replace the other at the same time since they're the same age, both are accessible during the same repair, and the second valve will likely fail in the near term. Always verify your model number before ordering. Key Features Aftermarket replacement built to OEM-equivalent quality standards Controls the flow of cold water into the washer during fill cycles Solenoid-actuated — opens precisely when the control board calls for cold water and closes the moment the call is dropped Resolves F8E1 and LO FL error codes when caused by a failed cold inlet valve 1/2" NPT threaded inlet for standard washer supply hose connection Dimensions: approximately 3" H x 4" W x 3" L Blue and white plastic body with metal solenoid coil — designed for long-term reliability against wash cycle pressure and temperature Replaces W11036930, W11316256, W11486361, AP7218603, EAP12711564, PD00086086, PS12711564, 4929298, and AP6835737 Compatible with Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, Magic Chef, Admiral, Norge, Roper, Inglis, and Kenmore front-load washers Often replaced together with the hot water inlet valve (W11688994, sold separately) as a paired repair Quick DIY repair — installs in 10–15 minutes with basic hand tools Product Specifications Part Number XPW11688995 Part Type Washer Water Inlet Valve (Cold) Condition Aftermarket Replacement Application Front-Load Washers (Whirlpool platform) Water Type Cold (paired hot valve is W11688994) Inlet Thread 1/2" NPT Dimensions Approximately 3" H x 4" W x 3" L Color Blue / White Material Plastic / Metal Error Codes Resolved F8E1, LO FL (when caused by cold valve fault) Often Paired With Hot Water Inlet Valve (W11688994, sold separately) Compatible Brands Whirlpool, Maytag, Amana, KitchenAid, Jenn-Air, Magic Chef, Admiral, Norge, Roper, Inglis, Kenmore Installation Notes ⚠️ Unplug Washer and Shut Off Water Supply Before Starting — Wear Work Gloves Disconnect power and shut off both the hot and cold water supplies at the wall before beginning. Wear work gloves to protect your hands. Have towels ready — residual water remains in the supply hoses and will spill when disconnected. Pull the washer out from the wall to access the back. Remove the three 1/4" screws securing the rear edge of the top cover, push the top cover slightly back, and lift it off. Locate the inlet valves at the back of the washer — the cold valve is typically blue. Disconnect the cold water supply hose from the valve (water will drip — towels). Photograph the wire connections before disconnecting. Unplug the small electrical connector from the valve solenoid. Remove the single 3/16" mounting screw (or similar hardware, model-dependent) holding the valve in place, and disconnect any internal water hoses from the valve outlet (channel-lock pliers may help with hose clamps). Install the new W11688995 valve in the same position with the same orientation, reconnect the internal water hoses and electrical connector, and secure the mounting screw. Reconnect the cold supply hose at the wall, restore water and power, and run a test cycle to confirm normal cold water fill with no leaks. Tip: while the top cover is off, this is the ideal time to also replace the hot water valve (W11688994) — they share the same access and lifespan. Tools needed: 1/4" nut driver, 3/16" nut driver, adjustable wrench or pliers, work gloves. Frequently Asked Questions What do error codes F8E1 and LO FL mean on Whirlpool washers? Both codes indicate a water fill problem. F8E1 appears when the control board doesn't detect normal water flow during a fill cycle — typically caused by a failed inlet valve, a clogged inlet screen, kinked supply hose, or restricted water supply. LO FL (low flow) appears when the washer detects that water is flowing in, but at a rate too low to complete the fill within the expected time window. When the cold water inlet valve has failed or is partially clogged, both codes can appear together. Before replacing the valve, check that the household cold water supply is on and the supply hose isn't kinked, and inspect the inlet screen on the valve for sediment buildup. If those check out, replacing the W11688995 typically resolves the codes. My washer isn't dispensing fabric softener — could this be the cold valve? Yes — this is actually a common symptom that's often misdiagnosed. The cold water inlet valve also feeds the detergent dispenser tray on most Whirlpool front-load washers, including the fabric softener compartment. If the cold valve is clogged or failing to fully open at the right moment in the cycle, water doesn't flow through the fabric softener compartment to flush it into the tub, leaving softener pooled in the tray at the end of the cycle. If you've already cleaned the dispenser tray and water lines and the problem persists, replacing the cold inlet valve (W11688995) often resolves the issue. Should I replace the hot water valve at the same time? Yes, it's strongly recommended. The cold and hot inlet valves are essentially identical components installed side by side at the back of the washer — they're the same age, are exposed to the same wash cycle stress, and have the same expected service life. When one fails, the other is typically not far behind. Since the top cover is already off and both valves are accessible during the same repair, replacing both saves you a second teardown later. The matching hot water valve is part number W11688994 (red, sold separately) and is also available as a paired kit. My washer is dripping water into the tub even when it's off — is this the valve? Yes, that's a classic sign of a failed inlet valve. When the solenoid wears out or debris keeps the valve from sealing fully closed, water leaks past it at low rates and drips into the tub even with the washer powered off — especially noticeable as a slow puddle forming over a day or two. Since both the hot and cold valves feed into the tub, you'll want to identify which one is leaking: shut off the hot water supply at the wall and check if dripping continues. If it stops, the hot valve is at fault; if it continues, this cold valve is the cause. Replacing the W11688995 will resolve a leaking cold valve. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the dimensions, electrical specifications, 1/2" NPT thread, and solenoid function of the original W11688995 cold water inlet valve used in compatible Whirlpool, Maytag, Amana, KitchenAid, and Kenmore front-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

W11457841 Genuine OEM Whirlpool Washer Lid Strike The W11457841 is a Genuine OEM Whirlpool replacement washer lid strike compatible with select Whirlpool, Maytag, and Kenmore HE top-load washers — including the Whirlpool WTW5100, WTW5105, WTW6120, WTW7120, WTW8120, WTW8127 series, and the Maytag MVW6200, MVW6230, MVW7230, MVW7232, MVW8230 series. The lid strike is the plastic component attached to the underside of the washer lid that physically engages the lid lock mechanism when the lid is closed. As the lid lowers into place, the strike enters the lock slot and activates the lid switch — signaling the control board that the lid is securely closed and the washer is safe to start agitation and spin. When the lid strike fails — typically by breaking off, cracking, or wearing down — the lid lock can't be properly activated, and the washer will not start, will stop mid-cycle, or will refuse to advance to the spin cycle. As a Genuine OEM part manufactured by Whirlpool to factory specifications, the W11457841 is the current production part, directly superseding W11091027. It also replaces 4959179, AP6987306, EAP16218028, PD00061788, and PS16218028. Installation is fast and simple — a counterclockwise twist removes the old strike, and a clockwise twist installs the new one. Installs in under 5 minutes, no special tools required. Quick Answer The W11457841 Genuine OEM Whirlpool Washer Lid Strike fixes Whirlpool, Maytag, and Kenmore HE top-load washers that won't start, won't lock the lid, stop mid-cycle, or won't advance to spin because the lid strike is broken or worn. Plastic strike that attaches to the underside of the washer lid and activates the lid lock and switch. Twist-in installation. Genuine OEM. Replaces W11091027, 4959179, AP6987306, EAP16218028, PD00061788, PS16218028. Compatible with Whirlpool WTW5100/5105/6120/7120/8120/8127 and Maytag MVW6200/6230/7230/7232/8230 series. Common Problems This Part Fixes Washer not starting — lid strike not engaging the lid lock Lid won't lock at the start of the cycle Washer stops mid-cycle with a lid-related fault Washer fills with water but won't agitate or advance to spin Lid strike visibly broken, cracked, or missing on the underside of the lid Strike worn down — physically fits the lock slot but no longer activates the lid switch Repeated lid lock errors despite the lid appearing to close normally Replaces Part Numbers This washer lid strike directly replaces the following OEM and cross-reference part numbers: W11457841, W11091027, AP6987306, AWP44638, PD00061788, EAP16218028, PS16218028. W11457841 is the current production part superseding W11091027. Contact our support team with your model number if you need confirmation before ordering. Compatibility This lid strike is compatible with select HE top-load washers from the following brands and series: Whirlpool top-load washers — WTW5100HC0, WTW5100HC1, WTW5100HC2, WTW5100HW0, WTW5100HW1, WTW5100HW2 series Whirlpool top-load washers — WTW5105HC0, WTW5105HC1, WTW5105HC2, WTW5105HW0, WTW5105HW1, WTW5105HW2 series Whirlpool top-load washers — WTW6120HC0, WTW6120HC1, WTW6120HC2, WTW6120HW0, WTW6120HW1, WTW6120HW2 series Whirlpool top-load washers — WTW7120HC0, WTW7120HW0 series Whirlpool top-load washers — WTW8120HC0, WTW8120HW0 series Whirlpool top-load washers — WTW8127LC0, WTW8127LC1, WTW8127LW0 series Maytag top-load washers — MVW6200KW0, MVW6200KW1, MVW6200KW2, MVW6200KW3 series Maytag top-load washers — MVW6230HC0, MVW6230HC1, MVW6230HC2, MVW6230HW0, MVW6230HW1, MVW6230HW2 series Maytag top-load washers — MVW6230RHW0, MVW6230RHW1, MVW6230RHW2 series Maytag top-load washers — MVW7230HC0, MVW7230HW0, MVW7230HW1 series Maytag top-load washers — MVW7232HC0, MVW7232HW0, MVW7232HW2 series Maytag top-load washers — MVW8230HC0 series Kenmore / Sears top-load washers (Whirlpool-built — select 110-series models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Genuine OEM part manufactured by Whirlpool to factory specifications — guaranteed fit and performance Plastic strike attaches to the underside of the washer lid and engages the lid lock mechanism when the lid closes Activates the lid switch to signal the control board that the lid is securely closed and the washer is safe to start Twist-in/twist-out installation — no tools or hardware required; counterclockwise to remove, clockwise to install Current production part — directly supersedes W11091027 Replaces W11091027, 4959179, AP6987306, EAP16218028, PD00061788, and PS16218028 Compatible with Whirlpool WTW5100/5105/6120/7120/8120/8127 and Maytag MVW6200/6230/7230/7232/8230 series HE top-load washers, plus select Kenmore Whirlpool-built models Fast DIY repair — installs in under 5 minutes Product Specifications Part Number W11457841 Supersedes W11091027 Part Type Washer Lid Strike Condition Genuine OEM Application HE Top-Load Washers (Whirlpool/Maytag/Kenmore platform) Material High-strength plastic Installation Twist-in (clockwise) / twist-out (counterclockwise) — no tools required Mounting Location Underside of washer lid Compatible Brands Whirlpool, Maytag, Kenmore Installation Notes ⚠️ Unplug Washer Before Starting — Wear Work Gloves Disconnect power before beginning. Wear work gloves to protect your hands. Open the washer lid and locate the lid strike on the underside of the lid — it's the small plastic peg that drops into the lock slot when the lid is closed. To remove the old strike: rotate the strike counterclockwise until the retaining tab breaks free and pulls back, then pull the old strike straight out. To install the new W11457841: align it with the mounting hole in the same orientation as the old one, and rotate clockwise until you hear or feel the retainer tab click into place. Close the lid and confirm the strike engages the lock slot properly. Restore power, start a test cycle, and confirm the lid locks and the washer begins normal operation. Tools needed: work gloves only — no tools required for the strike itself. Frequently Asked Questions What's the difference between the lid strike, lid lock, and lid switch? These three components work together as a safety system. The lid strike (W11457841) is the small plastic peg attached to the underside of the lid that physically enters the lock slot when the lid closes. The lid lock is the mechanism in the washer cabinet that grips the strike and physically locks the lid closed during the spin cycle. The lid switch is the electrical sensor inside the lock assembly that signals the control board when the strike is engaged. If the strike is broken or missing, none of the three can do their job — even if the lock and switch are working perfectly. Replacing just the strike often resolves "won't start" issues without needing to replace the more expensive lock assembly. What is the difference between W11457841 and W11091027? These are the same lid strike across production revisions. W11091027 was the earlier OEM part number, and W11457841 is the current production version that Whirlpool issued as a direct replacement. Both parts are physically and functionally identical — if your washer's parts diagram shows W11091027, the W11457841 is the correct current replacement, and this listing covers both numbers. My washer won't start and the lid seems to close normally — could this be the strike? Yes, this is one of the most common symptoms of lid strike failure on compatible Whirlpool and Maytag washers. Even though the lid appears to close, if the strike has cracked or worn down it may not physically engage the lock or activate the switch correctly. Visually inspect the strike on the underside of the lid — if it's broken, missing, or chipped, replacement is straightforward. If the strike looks intact and the washer still won't start, the lid lock assembly itself or the wiring harness may need attention. Do I really not need any tools to install this? Correct — the W11457841 lid strike uses a twist-in design with no screws or hardware. To remove the old strike, rotate it counterclockwise until the internal retaining tab breaks free, then pull it out. To install the new one, push it into the mounting hole and twist clockwise until it clicks into place. The whole replacement typically takes under 5 minutes once you have the new part in hand. Work gloves are recommended to protect your hands while gripping the small plastic part, but no other tools are needed. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It is the exact same lid strike installed in compatible Whirlpool, Maytag, and Kenmore HE top-load washers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 131763256 Washer Door Lock Assembly Replaces WH10X27534 The XPARTCO 131763256 is an aftermarket replacement door lock and switch assembly compatible with a wide range of Frigidaire, Electrolux, GE, White-Westinghouse, Tappan, Kenmore, Crosley, and Gibson front-load washers. The door lock latch and switch assembly is mounted on the front panel of the washer just inside the door opening — when the door closes, the door strike enters the lock and engages the latching mechanism, locking the door for the duration of the cycle and signaling the control board that it's safe to fill, agitate, and spin. Without a functioning door lock, the washer will not start, will not lock the door, may stop mid-cycle, or may display fault codes like E47. This is a universal-fit aftermarket assembly that spans both the Frigidaire platform (131763xxx-series part numbers) and the GE platform (WH10X-series part numbers) — one physical part covers both manufacturers' cross-referenced door lock positions on compatible front-load washers. Rated 120VAC, 50/60Hz, with 8 terminals. Dimensions: 4-1/2"L x 3-7/8"W x 1-1/2"H. Gray and red matte finish, plastic and metal construction. It directly replaces 131763256, 131763202, 131763255, 131763200, 131763245, 1317632, 1312694, 131269400, 137523400, 1531974, 3626240, 4547033, 4547432, 5301317632, 08003223, K001317632, K1317630-K938, K1317632, LP3202, PA66-GF25, WH10X27534, WH10X10003, WH10X10007, WH10X27194, AH2367737, AH3418879, AP4455026, AP4694680, AP6285657, AP6327625, EA3418879, EAP2367737, PD00038657, PD00070219, PS2367737, PS3418879, PS12343346, and PS12364048. Often replaced together with the matching door strike (131763310, sold separately). Installs in 15–20 minutes with basic hand tools. Quick Answer The XPARTCO 131763256 Washer Door Lock Assembly fixes Frigidaire, Electrolux, GE, Kenmore, Crosley, White-Westinghouse, Tappan, and Gibson front-load washers that won't start, won't lock the door, won't spin, won't drain, won't fill, stop mid-cycle, or display E47 error codes. Universal-fit assembly — spans both Frigidaire (131763xxx) and GE (WH10X) platforms. 120VAC, 50/60Hz, 8 terminals. 4-1/2"L x 3-7/8"W x 1-1/2"H. Gray/red matte. Replaces 131763202, 131763255, 131763200, 131763245, 1317632, 131269400, 4547033, WH10X27534, WH10X10003, WH10X10007, WH10X27194, AP6285657, AP4455026, PS2367737, and 20+ more cross-references. Often paired with the door strike (131763310, sold separately). Common Problems This Part Fixes Washer won't start — control board not detecting a locked door Door won't lock at the start of the cycle Washer stops mid-cycle due to a door lock fault E47 error code displayed on the control panel Washer pumps but won't spin — spin cycle blocked by unlocked-door detection Washer won't drain — drain cycle blocked by door-lock signal loss Washer won't fill with water — fill cycle blocked by door-lock signal Door lock assembly visibly broken, cracked, or missing latch teeth Door won't unlock at the end of the cycle — stuck lock mechanism Unusual noise from the door lock area during cycle transitions Replaces Part Numbers This universal-fit door lock assembly directly replaces the following OEM and cross-reference part numbers across multiple brands: 131763256, 131763255, 131763202, 1312694, 131269400, 131763200, 131763245, 3626240, 4547033, PA66-GF25, LP3202, AFR14205, AP6285657, EAP2367737, PD00038657, PS12364048, WH10X27534, WH10X10003, 08003223, 4547432, 5301317632, K001317632, K1317630-K938, K1317632, WH10X10007, WH10X27194, AP6327625, AGE754798, PS12343346, PD00070219, PD00070219. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This universal-fit door lock assembly is compatible with select front-load washers from the following brands: Frigidaire front-load washers — Affinity series, FAFS/FAFW/FFFS/FFFW/FRFW/FTF/FTR/FWFB/FWT/GLTF/GLEH series and many related models Electrolux front-load washers — select models with the matching door lock configuration GE front-load washers — WCCH404, WPXH214, WSSH300, WSXH208 series and related models (WH10X27534 cross-reference) White-Westinghouse front-load washers — select models Tappan front-load washers — select models Kenmore / Sears front-load washers — select Frigidaire-built and GE-built models Crosley front-load washers — BTF1240ES0, BTF1240ES1, BTF1240FS0 and related models Gibson front-load washers — select models Note: The door lock assembly (131763256) and the door strike (131763310) are two separate components that work together — if both are worn, replacing them together as a matched set ensures reliable door locking and prevents premature wear on the new lock. The strike is what physically enters the lock when the door closes. Always verify your model number before ordering. Key Features Universal-fit door lock and switch assembly — replaces both Frigidaire (131763xxx-series) and GE (WH10X-series) OEM door locks in a single aftermarket part Locks the washer door during the wash and spin cycles and signals the control board that the door is safely closed Resolves E47 error codes on compatible Frigidaire and Electrolux washers Rated 120VAC, 50/60Hz — correct electrical specifications for compatible washers 8 terminal connections for the wire harness Dimensions: 4-1/2"L x 3-7/8"W x 1-1/2"H Gray and red matte finish, plastic and metal construction Replaces 35+ OEM and cross-reference part numbers spanning Frigidaire, GE, Electrolux, and universal aftermarket catalogs Often replaced together with the matching door strike (131763310, sold separately) as a paired repair Compatible with Frigidaire, Electrolux, GE, White-Westinghouse, Tappan, Kenmore, Crosley, and Gibson front-load washers Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in 15–20 minutes with basic hand tools Product Specifications Part Number 131763256 Also Replaces (GE-side) WH10X27534 Part Type Washer Door Lock and Switch Assembly (Universal Fit) Condition Aftermarket Replacement Application Front-Load Washers (Frigidaire and GE platforms) Voltage 120V AC Frequency 50/60 Hz Terminals 8 Dimensions 4-1/2"L x 3-7/8"W x 1-1/2"H Color Gray / Red Finish Matte Material Plastic / Metal Error Codes Resolved E47 (door lock error) Often Paired With Door Strike (131763310, sold separately) Compatible Brands Frigidaire, Electrolux, GE, White-Westinghouse, Tappan, Kenmore, Crosley, Gibson Installation Notes ⚠️ Unplug Washer Before Starting — Wear Work Gloves Disconnect power before beginning. Wear work gloves to protect your hands. The door lock assembly is mounted on the front panel of the washer just inside the door opening. Open the washer door (if the door is stuck locked, use a putty knife to release the manual override latch through the bottom service opening, then open the door). Peel back the rubber door boot from the front panel edge to expose the mounting screws for the lock assembly — on some models this requires removing the spring-loaded wire clamp securing the boot with needle-nose pliers. Photograph the wire harness connections before disconnecting anything — this assembly has 8 terminals, so getting the wire mapping correct on reinstallation is important. Remove the 2 mounting screws holding the lock assembly to the front panel. Reach in and pull the assembly out through the door opening. Disconnect the wire harness plug from the old assembly. Snap the new 131763256 assembly onto the wire harness plug (should click firmly into place), position it in the front panel opening, and secure with the 2 mounting screws. Press the rubber door boot back into the groove at the front panel and reinstall the spring-loaded wire clamp if applicable — this is the trickiest part of the install. Restore power and test by closing the door and starting a cycle to confirm the door locks and the washer runs normally. Tools needed: Phillips screwdriver, needle-nose pliers, putty knife (for stuck doors), work gloves. Frequently Asked Questions Does this really fit both Frigidaire AND GE washers? Yes — this is one of those cases in front-load washer parts where an aftermarket door lock assembly has been designed to serve as a direct replacement for both the Frigidaire 131763xxx-series and the GE WH10X-series door locks. The two OEM assemblies share the same physical dimensions, 8-terminal wire harness configuration, and mounting geometry, allowing a single aftermarket part to function correctly in both platforms. Compatible models span Frigidaire's Affinity series, GE's WCCH/WPXH/WSSH/WSXH series, and select Electrolux, Kenmore, Crosley, White-Westinghouse, Tappan, and Gibson front-load washers. Always verify your specific model number before ordering. What does error code E47 mean on my Frigidaire washer? E47 on Frigidaire and Electrolux front-load washers indicates a door lock circuit fault — the control board is not receiving the expected signal from the door lock assembly to confirm the door is closed and locked. This is typically caused by a failed door lock assembly, but can also be caused by a broken door strike (which physically enters the lock), a damaged wire harness, or a control board issue. Replacing the 131763256 door lock resolves E47 when the lock is the cause; if the code returns after replacement, check the strike and the wire harness next. My washer won't drain and won't spin — is the door lock the problem? Possibly, yes. Front-load washers block drain and spin operations whenever the control board can't confirm the door is locked — this is a safety measure to prevent water release and drum spinning while the door might be open. If your washer fills but won't advance to drain and spin, and there are no obvious pump or motor problems, a failed door lock is a common cause even though the symptom doesn't directly say "door." The failure can also manifest as "won't fill" or "unusual noise" during cycle transitions. Testing the door lock with a multimeter (or replacing it as a diagnostic step given the low cost) is a good first move for these symptoms. My washer door is stuck closed — how do I get it open to install this? If the door is stuck in the locked position because of a failed door lock, you can use a putty knife or thin flat tool to manually release the lock through the bottom service opening at the front of the washer. Reach in through the access panel at the lower front and locate the manual release lever or latch on the back of the door lock assembly — gently push or pry it to release the mechanism. The door should then open. Once open, you can proceed with the installation. Always disconnect power from the washer first. Do I need to replace the door strike (131763310) too? Not always, but often. The door strike is the matching component mounted on the washer door itself — it's the part that the lock's latching mechanism grips when the door closes. If the strike is worn, cracked, or its plastic teeth are broken, the new lock won't engage reliably even if it's working perfectly. Inspect the strike on the door for visible damage before ordering just the lock. Many repair scenarios call for replacing both at the same time since both wear together and the parts complement each other. The matching strike is part number 131763310 (sold separately). Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Frigidaire, GE, or Electrolux OEM part, but is manufactured from plastic and metal to match the dimensions (4-1/2"L x 3-7/8"W x 1-1/2"H), electrical specifications (120V AC, 50/60Hz), 8-terminal wire harness configuration, and lock engagement function of the original door lock assemblies it replaces across multiple manufacturers' catalogs. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less