XPARTCO W10820036 Washer / Dryer Door Switch
The XPARTCO W10820036 is an aftermarket replacement door switch used on select Whirlpool-built combination washer/dryer units. This switch is a safety interlock: it detects whether the door is fully closed and latched, and it signals the control board that it is safe to run the motor, heater, and water valves. On a combo unit, this single interlock typically governs both the wash and dry portions of the cycle, since both functions share the same drum and door. If the switch fails to detect a closed door — or fails electrically even when the door is closed properly — the control will refuse to start the cycle, or will stop mid-cycle if the switch drops out while running.
Typical failure modes for a part like this include a cracked or worn switch lever that no longer depresses fully when the door closes, internal contacts that have pitted or burned out from years of cycling, and a housing that has come loose from its mounting bracket so the plunger no longer lines up with the door strike. A functioning door switch should click firmly when the door closes and should show continuity across its terminals only when the lever is pressed.
Quick Answer
The XPARTCO W10820036 Washer/Dryer Door Switch is a door safety interlock switch for select Whirlpool-built combination washer/dryer units. It fixes units that won't start with the door closed, stop mid-cycle, or fail to register the door as closed even when it's latched properly. Note: this listing was built from general parts knowledge because current supplier and cross-reference data was not available at build time — see the note below before publishing.
Common Problems This Part Fixes
Washer/dryer combo won't start even though the door is fully closed
Cycle stops partway through, as if the door had been opened
Door doesn't feel like it's "clicking" or latching the way it used to
Console shows a door-related error or won't advance past the door-closed step
Intermittent operation — sometimes starts, sometimes doesn't, depending on how the door is closed
Visibly cracked, loose, or broken switch housing or lever
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This door switch directly replaces the following OEM part number:
W10820036, 279347, 2-2770, 2-50062, 2-5415, 2020, 202770, 233480, 235462, 237194, 238775, 238980, 239868, 24198, 247207, 26000279347, 279290, 287219, 287220, 291679, 291697, 292212, 296141, 296144, 3347287, 338883, 3392266, 3397503, 3399991, 347207, 350526, 359230, 359484, 364090, 364091, 367034, 388322, 389105, 4273196, 4319330, 660308, 687429, 75958, 8224, 83333, 84144, 86628, 89556, 99788, 99838, LP210, AP5985146, AWP41434, EAP334185, PD00023982, PS11723153.
No additional cross-reference numbers have been confirmed for this part yet. If you have a superseded or alternate number for your appliance, contact our support team and we will verify compatibility before you order.
Compatibility
This door switch is intended for select Whirlpool-built washer/dryer combination units, where a single door and drum serve both the wash and dry functions.
Model list not yet confirmed: A specific compatible model list for W10820036 was not available at the time this page was built. Please verify your exact model number before ordering. Contact our support team with your model number and we will confirm fitment before you purchase.
Key Features
Aftermarket replacement door safety switch for Whirlpool-built washer/dryer combo units
Detects whether the door is closed and latched before allowing the wash or dry cycle to run
Resolves "won't start with door closed," "stops mid-cycle," and "door not detected" symptoms
Direct drop-in replacement for the original W10820036 switch — no modification required
Aftermarket replacement built to OEM-equivalent quality standards
Product Specifications
Part Number
XPW10820036
OEM Part Number
W10820036
Part Type
Washer/Dryer Combo Door Safety Switch
Condition
Aftermarket Replacement
Application
Whirlpool-Built Washer/Dryer Combination Units
Function
Door-closed safety interlock for wash and dry cycles
Quantity
1 switch
Compatible Brand
Whirlpool (combo platform)
Installation Notes
⚠️ Unplug The Unit Before Starting Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access to the door switch on combo units is typically through the front or top control panel — photograph the wiring harness before disconnecting it so you can match it exactly on reassembly. Confirm the new switch's lever aligns with the door strike before securing the mounting screws, and test for a firm, positive click when the door closes before restoring power and running a cycle. If your unit's service manual is available, follow its specific access and mounting steps rather than relying solely on general guidance.
Frequently Asked Questions
My combo unit won't start. Is this definitely the door switch?
It's one of the most common causes when a unit refuses to start with the door visibly closed. Before replacing the switch, confirm the door is latching fully and that nothing (a stray sock, a bent strike bracket) is preventing it from closing all the way. If the door latches firmly but the unit still won't start, or a multimeter shows no continuity across the switch terminals when the lever is pressed, the switch itself is the likely culprit.
Does this switch control both the washer and dryer functions?
On combination washer/dryer units, yes — a single door and drum typically serve both functions, so one door switch acts as the safety interlock for both the wash and dry portions of the cycle.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the mounting, switching function, and door-interlock behavior of the original W10820036 switch used in compatible combination washer/dryer units.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
DC34-00025G Washer Genuine OEM Lid Switch and Lock Assembly – Fits Samsung Washers
Product Overview
The DC34-00025G Washer Lid Switch and Lock Assembly is a genuine OEM replacement part that ensures your washer lid stays securely locked during wash and spin cycles. This part detects when the lid is closed and locks it to prevent accidental opening, providing safety and proper cycle operation. A worn or broken lid lock can cause your washer to stop mid-cycle, display error codes, or fail to start. Replacing it restores dependable washer performance and safety compliance.
Replaces Part Numbers
This lid switch and lock assembly replaces DC34-00025G, AP6884125, PS12720530.
Manufactured to original equipment specifications for a precise fit and long-term durability.
Compatible Brands
Compatible with select Samsung top-load washers manufactured by Samsung. Fits a variety of models using this specific lid lock assembly.
Fixes the Following Issues
Washer won’t start or stops mid-cycle
Lid doesn’t lock properly
Error codes related to lid switch or lock failure
Washer won't enter spin or drain cycles
Why Buy from Parts‑O‑Matic
Factory-original genuine OEM part
Fast and free U.S. shipping
Trusted by appliance professionals and DIYers
Backed by reliable customer support
XPARTCO 3406107 Dryer Door Switch – Replaces WP3406107 – Compatible with Whirlpool, Kenmore, Maytag, and Amana Dryers
Product Description
Ensure your dryer starts safely and operates correctly with the XPARTCO 3406107 Dryer Door Switch. This high-quality aftermarket replacement detects when the dryer door is closed, enabling the motor to run and heat to activate. A defective switch can prevent your dryer from starting or cause it to stop mid-cycle. Replacing it with this reliable XPARTCO switch restores normal operation and dependable performance.
Replaces Part Numbers
WP3406107, WPW10569603, 3406107, 3406109, W10569603, 3405100, 3405101, 3406100, 3406101, ES6107, 528948, 11259-65, PD00002378, EAP11741701, AP6008561, PS11741701.
Compatibility
This replacement door switch fits select Whirlpool, Kenmore, Maytag, Amana, Crosley, and Estate dryers.
Example compatible models include (but are not limited to): Whirlpool WED4815EW1, Kenmore 110.60902990, and Maytag MEDC200XW1.
Always verify your dryer’s model number before ordering. Contact our support team if you’re unsure.
✅ Key Features
🔄 Aftermarket Replacement – Engineered to match OEM safety and electrical performance
🚪 Restores Start Function – Ensures dryer runs only when the door is fully closed
💰 Affordable Solution – Quality replacement at a lower cost than OEM parts
🛠️ Quick Installation – Simple plug-in wiring and snap-in mounting
🛡️ Fixes Common Issues – Solves dryer not starting, shutting off mid-cycle, or running with door open
📐 Product Specification
Part Number: 3406107
Component Type: Dryer Door Switch Assembly
Material: Plastic body with metal actuator lever and 3-pin terminal
Mounting: Snap-in installation behind front panel
Electrical Rating: 15A / 125-250V AC
Compliance: Built to OEM-equivalent quality standards (not OEM)
🛠️ Installation Notes
Tools Needed: Phillips screwdriver, nut driver
⚠️ Safety First: Always unplug the dryer before servicing to prevent electrical shock.
Steps:
Disconnect power and open the dryer door.
Remove the top or front panel (depending on model).
Unplug the old switch’s wire connectors.
Press the locking tabs and remove the old switch.
Install the new XPARTCO 3406107 switch, reconnect wires, and secure panels.
Restore power and test dryer start function.
⏱️ Time Required: 10–15 minutes
📦 Shop With Confidence
🚚 Free Shipping on All Orders
⚙️ Trusted Appliance Parts Supplier
🔄 30-Day Return Policy
Restore your dryer’s start function — Add to Cart Now for a reliable, budget-friendly repair!
XPARTCO W10006355 Washer Shift Actuator
Fits specific Maytag, Kenmore, Whirlpool top-load machine models.
Replaces Part Numbers: WPW10006355, W10006355, AP6014711, PS11747977.
Description: This Shift Actuator is a replacement part for specific Maytag, Kenmore, Whirlpool washing machine models. It is an electronic component located inside the transmission that controls the shifting between wash cycles. The shift actuator receives signals from the washer control board to change modes, initiating proper movements to advance the cycle.
This is an aftermarket part that can be used as a replacement for the OEM part.
XPARTCO 3355806 Washer Lid Switch Replaces WP3355806
The XPARTCO 3355806 is an aftermarket replacement stackable washer lid switch assembly compatible with a wide range of Whirlpool, Kenmore, Roper, Estate, KitchenAid, Maytag, Admiral, Amana, Crosley, Inglis, and Magic Chef stacked washer/dryer laundry centers (thin twin and space-saver units). The lid switch is a safety component mounted near the top of the washer — it detects whether the lid is open or closed and prevents the washer from spinning while the lid is open. When you close the lid, a pin on the lid activates the lever on the switch, signaling the control that it's safe to spin. Without a functioning lid switch, the washer won't spin as a safety measure, even though it may still fill and agitate normally.
The switch commonly fails in one of two ways: the plastic body cracks from the lid being slammed over time, or the internal switch contacts wear out and can no longer signal that the lid is closed. Features an 11" wiring harness with round plugs and a 7/8" block connector. It directly replaces WP3355806, WP3355806VP, 3355806, 520880, AP6008072, AP2947199, AH11741201, EA11741201, EAP11741201, PS11741201, PS341529, and PD00002599. Installs in 15–30 minutes with basic hand tools and novice repair experience.
Quick Answer
The XPARTCO 3355806 Washer Lid Switch fixes Whirlpool, Kenmore, Roper, Estate, and KitchenAid stacked washer/dryer laundry centers where the washer won't spin but still agitates and fills, the machine doesn't detect the lid is closed, or the washer won't start. Stackable washer lid switch assembly — 11" harness with round plugs, 7/8" block. Replaces WP3355806, WP3355806VP, 520880, AP6008072, AP2947199, AH11741201, EA11741201, EAP11741201, PS11741201, PS341529. Compatible with Whirlpool LTE5243/LTG5243 series, Roper RTE5243/RTG5243, and Kenmore thin twin models. Classic symptom: won't spin but still agitates.
Common Problems This Part Fixes
Washer won't spin but still agitates and fills — the classic lid switch failure symptom
Washer won't start at all — control not detecting a closed lid
Machine doesn't recognize the lid is closed even when it is
Lid switch body cracked from the lid being slammed over time
Internal switch contacts worn out — no longer signaling lid closed
Washer stops mid-cycle when it should transition to spin
Clothes coming out sopping wet because the spin cycle never runs
Intermittent operation — washer sometimes spins, sometimes doesn't, depending on lid position
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This washer lid switch directly replaces the following OEM and cross-reference part numbers:
WP3355806, ER3355806, 3355806, AP6008072, AWP47529, EAP11741201, PD00002599, PS11741201.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This lid switch assembly is compatible with select stacked washer/dryer laundry centers (thin twin / space-saver units) from the following brands:
Whirlpool laundry centers — LTE5243DQ0-DQ8, LTE5243DT2-DT7, LTE5243DZ0/DZ1/DZ2, LTE5243BN0/BN1, LTG5243DQ0-DQC, LTG5243DT3/DT4/DT7/DT8, LTG5243DZ1/DZ2, LTG5243BN0/BN1 series and related
Whirlpool laundry centers — WET4024EW and related stacked models
Roper laundry centers — RTE5243BL0, RTE5243BW0, RTG5243BL0, RTG5243BW0 series
Kenmore / Sears laundry centers — thin twin models (110.9975820, 110088732791-11088754793, 11098573100-11098573800 series and related)
Estate, KitchenAid, Maytag, Admiral, Amana, Crosley, Inglis, Magic Chef — select stacked washer/dryer models
Always verify your appliance model number before ordering. Contact our support team if you're unsure.
Key Features
Stackable washer lid switch assembly — detects whether the lid is open or closed and prevents spinning when the lid is open
Resolves the classic "won't spin but still agitates" symptom of lid switch failure
Restores the safety interlock and allows the washer to complete its spin cycle
Features an 11" wiring harness with round plugs and a 7/8" block connector
Designed for thin twin, space-saver, and other stacked washer/dryer laundry centers
Replaces WP3355806, WP3355806VP, 520880, AP6008072, AP2947199, AH11741201, EA11741201, EAP11741201, PS11741201, PS341529, and PD00002599
Compatible with Whirlpool LTE5243/LTG5243 series, Roper RTE5243/RTG5243 series, and Kenmore thin twin laundry centers, plus Estate, KitchenAid, Maytag, Admiral, Amana, Crosley, Inglis, and Magic Chef stacked units
Aftermarket replacement built to OEM-equivalent quality standards
Quick DIY repair — installs in 15–30 minutes with basic hand tools
Product Specifications
Part Number
3355806
OEM Part Number
WP3355806
Part Type
Stackable Washer Lid Switch Assembly
Condition
Aftermarket Replacement
Application
Stacked Washer/Dryer Laundry Centers (Whirlpool platform)
Harness Length
11" with round plugs
Block Connector
7/8"
Function
Prevents washer spin when lid is open
Location
Near top of washer, behind front panel
Compatible Brands
Whirlpool, Kenmore, Roper, Estate, KitchenAid, Maytag, Admiral, Amana, Crosley, Inglis, Magic Chef
Installation Notes
⚠️ Unplug Washer and Shut Off Water Before Starting — Wear Work Gloves Unplug the appliance (or shut off the house circuit breaker) and turn off the hot and cold water supplies before beginning. Wear work gloves to protect your hands. On these stacked laundry centers, the lid switch is accessed by removing the front panel or the top panel — unscrew the screws along the edge of the panel and set it aside. Note: on some Whirlpool space-saver units, the hardest part of the job is getting the washer lid off to access the switch, so take your time and consult a model-specific diagram or video. Once the panel is off, locate the lid switch assembly near the top of the machine. Photograph the wiring harness connections before disconnecting anything. Unscrew the retaining screws that hold the lid switch in place, then carefully disconnect the wiring harness from the switch. Connect the wiring harness to the terminals on the new 3355806 switch, following the diagram on the switch for proper installation. Secure the new switch in place with the retaining screws. Reinstall the panel and secure it with the screws. Turn the water supplies back on, plug the washer back in, and test by closing the lid and running a cycle — the machine should advance to spin when the lid is shut. Tools needed: Multi-screwdriver, socket wrench (some models), work gloves.
Frequently Asked Questions
My washer agitates and fills but won't spin — is the lid switch the cause?
Yes — this is the single most common and telling symptom of a failed lid switch. The lid switch is a safety interlock that prevents the drum from spinning while the lid is open. When the switch fails (cracked body or worn internal contacts), the control never receives the "lid closed" signal, so it blocks the spin cycle as a safety measure — but agitation and fill still work because those don't require the lid interlock. If your washer runs through wash and agitate normally but stops when it should spin, leaving clothes sopping wet, the lid switch is the prime suspect. You can confirm by testing the switch for continuity with a multimeter when the lever is pressed.
What causes the lid switch to fail?
There are two common failure modes. First, the plastic body of the switch can crack over time from the lid being closed hard or slammed repeatedly — the repeated impact stresses the housing until it fractures. Second, the internal electrical contacts wear out from thousands of open/close cycles and can no longer make a reliable connection to signal that the lid is closed. Either way, the fix is the same: replace the lid switch assembly. To extend the life of the new switch, close the lid gently rather than letting it slam.
What's the difference between 3355806 and WP3355806?
These are the same lid switch across production revisions. 3355806 was the original part number and WP3355806 is the Whirlpool-era part number (with the "WP" prefix Whirlpool adopted) for the same switch. WP3355806VP is a variant packaging code. All are physically and functionally identical — if your laundry center's parts diagram shows any of these numbers, this listing is the correct replacement. The cross-references 520880, AP6008072, and PS11741201 are additional catalog identifiers for the same part.
Does this fit my thin twin or space-saver laundry center?
This lid switch is specifically designed for stacked washer/dryer laundry centers — the "thin twin," space-saver, and similar stacked units from Whirlpool and its related brands. It fits the Whirlpool LTE5243/LTG5243 series, Roper RTE5243/RTG5243 series, and a wide range of Kenmore thin twin models, among others. Check your model number against the compatibility list above. If your unit is a standalone (non-stacked) top-load washer, it likely uses a different lid switch — contact our support team with your model number and we'll confirm the correct part.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the fit, 11" harness with round plugs, 7/8" block connector, terminal configuration, and lid-detection function of the original WP3355806 lid switch used in compatible Whirlpool, Kenmore, Roper, Estate, and related stacked washer/dryer laundry centers.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
XPARTCO DG34-00027B Range Membrane Switch (Touchpad)
The XPARTCO DG34-00027B is an aftermarket replacement membrane switch touchpad for Samsung gas ranges. This is the keypad panel itself — the physical layer of touch-sensitive buttons you press to select temperature, set the time, and choose a cooking mode. Underneath a thin, durable overlay, this membrane switch reads each button press as a distinct signal and passes it along to the range's main control board, which then acts on the command. Unlike the main control board, this component doesn't process or execute anything on its own — it's purely the interface between your finger and the board.
Because of that division of labor, a failing membrane switch produces a very specific pattern that's easy to distinguish from a control board failure: certain buttons stop responding, specific functions become impossible to select, or particular settings can no longer be adjusted, while the rest of the panel — including the clock, display, and other buttons — continues working normally. If instead the entire display goes blank or the whole panel stops responding at once, that points to the main control board rather than this touchpad. It directly replaces DG34-00027A, AP5986689, and PS11735749.
Quick Answer
The XPARTCO DG34-00027B Range Membrane Switch (Touchpad) fixes Samsung gas ranges where certain buttons don't respond, specific functions can't be selected, or particular settings won't adjust — while the rest of the control panel, including the clock and display, still works normally. Replaces DG34-00027A, AP5986689, PS11735749. If the entire display is blank or completely unresponsive, or the clock works but no heating functions operate at all, the problem is more likely the main control board (such as our DE92-02588G listing) rather than this touchpad.
Common Problems This Part Fixes
Certain buttons on the control panel don't respond when pressed
Specific cooking functions or modes can't be selected
Particular temperature or time settings can't be adjusted
Some buttons work fine while others are unresponsive or intermittent
Touchpad feels unresponsive or requires repeated presses to register
Visible wear, cracking, or bubbling on the touchpad overlay surface
Buttons that used to work reliably have become inconsistent over time
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This range membrane switch touchpad directly replaces the following OEM and cross-reference part numbers:
DG34-00027B, DG34-00027A, AP5986689, ASM912846, EAP11735749, PD00027535, PS11735749
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This membrane switch touchpad is compatible with select Samsung gas ranges, including model numbers such as:
NX58H5600SS
NX58J5600SG
NX58F5700WS
NX58M5600SB
Note: Samsung uses several similarly-numbered membrane switch touchpads across its range lineup — including DG34-00025A (for NX58F5300SS/NX58F5500SS/NX58F5500SB), DG34-00020A (for NE594R0/NE59J3420/NE59J3421), and DG96-00850H (for NE63A6511) — each for different model groups and not interchangeable with this one. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which touchpad fits your range.
Key Features
Aftermarket replacement membrane switch touchpad — the touch-sensitive keypad interface for the control panel
Resolves "certain buttons unresponsive," "can't select specific functions," and "settings won't adjust" symptoms caused by a worn or damaged membrane
Durable overlay material designed for long-term wear resistance
Smooth surface that's easy to clean and maintain
Direct drop-in replacement — matches the original control panel mounting
Replaces DG34-00027A, AP5986689, and PS11735749
Aftermarket replacement built to OEM-equivalent quality standards
Straightforward DIY repair with basic tools
Product Specifications
Part Number
XPDG34-00027B
OEM Part Number
DG34-00027B (also DG34-00027A)
Part Type
Range Membrane Switch (Touchpad)
Condition
Aftermarket Replacement
Application
Gas Ranges
Color
Black
Function
Touch-sensitive keypad interface; passes button signals to the main control board
Quantity
1 membrane switch touchpad
Compatible Brand
Samsung
Installation Notes
⚠️ Unplug Range Or Shut Off Breaker Before Starting — Small Parts, Keep Away From Children Unplug the range or shut off the house circuit breaker before beginning to avoid electrical hazards. Wear work gloves. This part includes small components — keep them away from young children during installation. Access is typically through the front of the control panel: remove the screws or clips securing the panel trim, then carefully separate the old touchpad overlay from its mounting surface, since some models use an adhesive backing that may require gentle, even pressure to release cleanly without damaging the surrounding panel. Photograph the ribbon cable or connector routing before disconnecting anything. Disconnect the touchpad's ribbon cable or connector from the control board, and remove the old membrane switch fully. Position the new DG34-00027B so its buttons align correctly with the control panel cutout, press it into place evenly to seat any adhesive backing, and reconnect the ribbon cable or connector to the control board. Reinstall the panel trim and its screws or clips. Restore power and test every button on the touchpad to confirm each one now responds correctly. Tools needed: Phillips or flat-blade screwdriver (model-dependent), work gloves.
Frequently Asked Questions
Some buttons work but others don't. Is this the right part?
Yes, this is the classic symptom this touchpad addresses. Because the membrane switch is purely the physical button interface, individual sections of it can wear out or fail independently, leaving some buttons responsive while others stop working. If your clock, display, and some functions still work normally but specific buttons or settings don't respond, this touchpad — not the main control board — is the most likely cause.
My whole display is blank and nothing on the panel responds. Do I need this part?
Probably not. A completely blank or entirely unresponsive display points to the main control board rather than this touchpad, since the touchpad itself has no display and can't cause a total blackout on its own. Similarly, if your clock and timer work but no oven heating functions operate at all, that's also a control board symptom. This touchpad is the correct part specifically when some buttons or functions fail while the rest of the panel, including the display, continues working.
How do I know which specific membrane switch touchpad my range needs?
Samsung uses several different touchpads that look similar but serve different model groups — always check your full model number before ordering. This DG34-00027B fits NX58H5600SS, NX58J5600SG, NX58F5700WS, and NX58M5600SB specifically; other Samsung ranges use different part numbers such as DG34-00025A, DG34-00020A, or DG96-00850H. Contact our support team with your model number if you want to confirm before ordering.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured to match the button layout, overlay material, and mounting configuration of the original DG34-00027B touchpad used in compatible Samsung gas ranges.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
XPARTCO XPDC35X5-450R Dual Run Capacitor (35/5 MFD, 450V, Round)
The XPARTCO XPDC35X5-450R is a universal dual run capacitor for central air conditioners, heat pumps, and condensing units. A run capacitor works alongside a single-phase AC motor to keep it running efficiently once it's started, boosting torque and correcting the phase of the current feeding the motor's windings. This is a dual capacitor, meaning it combines two separate capacitors — one for the compressor, one for the condenser fan motor — into a single three-terminal can, which is why nearly every residential outdoor AC unit uses exactly this style of component to run both motors from one part.
Rated 35 MFD for the compressor circuit and 5 MFD for the fan motor circuit, at 450VAC, in a round aluminum can housing. Because a capacitor's voltage rating is a ceiling rather than a fixed match, this 450V-rated capacitor can safely replace an original capacitor rated 370V or 440V — going higher on voltage is always safe, going lower is not. Over time, the dielectric material inside a run capacitor breaks down from heat cycling and electrical stress, causing it to lose capacitance or fail outright. A failing dual capacitor produces a very recognizable set of symptoms: the outdoor unit hums but the compressor or fan won't start, the fan spins slowly or needs a manual push to get going, the system trips the breaker, or the capacitor can itself is visibly bulging, domed, or leaking oily residue at the top.
Quick Answer
The XPARTCO XPDC35X5-450R Dual Run Capacitor fixes central air conditioners and heat pumps where the outdoor unit hums but won't start, the compressor or fan motor won't run, the fan spins slowly or needs a manual push, the breaker trips, or the capacitor can is visibly bulged or leaking. 35 MFD (compressor) + 5 MFD (fan) dual capacitor, 450VAC, round, 3-terminal. Universal fit for equipment originally speced at 370V or 440V, since a higher voltage rating is always a safe upgrade. Capacitors store a dangerous electrical charge even after power is disconnected — always discharge before handling.
Common Problems This Part Fixes
Outdoor AC unit hums but the compressor won't start
Condenser fan won't spin, or spins slowly and needs a manual push to get going
System trips the breaker shortly after starting
AC blows warm air because the compressor isn't running
Repeated clicking sound from the contactor as it tries and fails to start the motor
Capacitor can visibly bulging, domed on top, or leaking oily residue
System that used to start slowly and has now stopped starting altogether
Burning smell from the outdoor unit's electrical compartment
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
XPDC35X5-450R
This is a universal component rather than a single-manufacturer part, so the specific OEM number your HVAC system's label references will vary by brand (Goodman, Trane, Carrier, Rheem, York, Lennox, Amana, and others). This capacitor is a correct replacement for any dual run capacitor matching the 35 MFD / 5 MFD rating with a voltage rating of 450V or lower. If you have your original part number, contact our support team and we will verify compatibility before you order.
Compatibility
This dual run capacitor is a universal replacement compatible with central air conditioners, heat pumps, and condensing units across all major HVAC brands, wherever the original capacitor is rated:
35 MFD (compressor) + 5 MFD (fan motor)
370V, 440V, or 450V (this capacitor's 450V rating exceeds and safely replaces either lower rating)
Round can shape with 3 terminals
Note: The MFD (microfarad) rating must match your original capacitor exactly on both sides — do not substitute a different MFD value for either the compressor or fan side. Voltage rating, on the other hand, can be equal to or higher than the original (450V safely replaces 370V or 440V), but never lower. Can shape (round vs. oval) affects only physical fit inside your unit's electrical compartment, not performance. If you're unsure of your original capacitor's specifications, they're printed directly on its can — contact our support team if you'd like help confirming compatibility.
Key Features
Universal dual run capacitor — supports both the compressor and condenser fan motor from one component
35 MFD compressor rating + 5 MFD fan motor rating in a single 3-terminal can
450VAC rating — a safe upgrade replacement for equipment originally speced at 370V or 440V
Round aluminum can construction
Resolves "hums but won't start," "fan spins slowly," "trips the breaker," and "bulging or leaking can" symptoms caused by capacitor failure
1/4" quick-connect terminals for a direct plug-on fit to standard HVAC wiring
50/60Hz rated
Safety approved: CQC, VDE, TÜV, and CL; built to GB/T 3667 and EN 60252 standards
Built to meet or exceed industry-standard specifications for this capacitor class
Product Specifications
Part Number
XPDC35X5-450R
Part Type
Dual Run Capacitor
Condition
New — Universal Replacement Part
Capacitance — Compressor
35 MFD (µF)
Capacitance — Fan Motor
5 MFD (µF)
Voltage Rating
450VAC
Shape
Round
Terminals
3 (1/4" quick-connect)
Frequency
50/60 Hz
Tolerance
±5%
Construction Type
Polypropylene film capacitor
Operating Temperature Range
-40°C to 70°C (-40°F to +158°F)
Safety Approvals
CQC, VDE, TÜV, CL
Approval Standard
GB/T 3667, EN 60252
Application
Central Air Conditioners, Heat Pumps, Condensing Units
Quantity
1 dual run capacitor
Compatible Brands
Universal — all major HVAC brands
Installation Notes
⚠️ Danger — Capacitors Store A Dangerous Electrical Charge Shut off power to the outdoor unit at the disconnect box and at the breaker before beginning. A capacitor stores an electrical charge even after power has been disconnected, and that charge can deliver a serious or fatal shock. Before touching any terminal, discharge the capacitor by shorting each pair of terminals together (C-to-Fan, C-to-Herm, and Fan-to-Herm) using an insulated-handle screwdriver, or by using a proper capacitor discharge tool with a resistor. Never short the terminals with a bare metal tool held with your bare hand. If you are not fully comfortable performing a capacitor discharge safely, have a qualified HVAC technician replace this part instead.
⚠️ Photograph The Wiring Before Disconnecting — Match Terminals Exactly Wear work gloves and safety glasses. After confirming the capacitor is fully discharged, photograph the wiring on the old capacitor's terminals before disconnecting anything — dual capacitors are labeled C (Common), Herm or Comp (compressor/hermetic), and Fan, and getting a wire on the wrong terminal can damage the new capacitor or the motor it feeds. Note which terminal each wire came from, or label them individually with tape. Remove the mounting strap or bracket holding the old capacitor in its housing, and disconnect each wire from its terminal. Install the new XPDC35X5-450R in the same mounting position, secure it with the strap or bracket, and reconnect each wire to the matching terminal (C, Herm, and Fan) exactly as labeled. Double-check every connection before restoring power. Restore power at the breaker and disconnect box, and confirm the compressor and fan both start promptly and run smoothly. Tools needed: insulated-handle screwdriver or capacitor discharge tool, nut driver, work gloves, safety glasses.
Frequently Asked Questions
My AC unit hums but won't start. Is this the capacitor?
It's one of the most common causes of exactly that symptom. A run capacitor gives the compressor or fan motor the extra push needed to start turning; without it, the motor can draw power and hum in place without ever actually starting to spin. If you can see the capacitor can and it looks bulged, domed on top, or is leaking a brown oily residue, that's strong visual confirmation of failure.
Can I use a 450V capacitor to replace my old 370V or 440V one?
Yes. Voltage rating is a ceiling, not an exact match requirement — a capacitor rated for a higher voltage than your original will work safely and often lasts longer under the same electrical stress. What you cannot do is go the other direction: never install a capacitor with a lower voltage rating than your original, since that risks premature failure or the capacitor breaking down under normal operating conditions.
Does the round vs. oval shape matter?
Only for physical fit inside your unit's electrical compartment — it has no effect on electrical performance. If your unit's mounting bracket or available space is sized for a round can, use a round capacitor; if it's sized for an oval can, use an oval one. The MFD and voltage ratings are what matter electrically, not the shape.
The fan spins if I give it a push, but won't start on its own. What does that mean?
This is a classic sign of a weak or failing capacitor — it may still have enough charge to keep the motor running once it's already spinning, but not enough to provide the initial starting torque. This is a strong signal to replace the capacitor before it fails completely and leaves you with no cooling at all.
Is this a genuine OEM part?
This is a universal replacement part rather than a brand-specific OEM part. Because dual run capacitors are a standardized component defined by their electrical specifications rather than their manufacturer, this capacitor is a correct replacement for any unit's original capacitor that shares the same 35/5 MFD, 450VAC, round dual run capacitor rating — regardless of which HVAC brand originally installed it.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Quality Replacement Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout
XPARTCO 3406105 Dryer Door Switch Replaces WP3406105
The XPARTCO 3406105 is an aftermarket replacement dryer door switch assembly compatible with a wide range of Whirlpool-family dryers including Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Estate, Crosley, Inglis, Admiral, Jenn-Air, Magic Chef, and Norge. The door switch is a safety component mounted inside the dryer cabinet near the door opening. When the door is closed, the door strike depresses the switch actuator, completing the circuit and allowing the dryer to start and run. When the door is opened, the switch opens the circuit and stops the dryer. On models with a broken belt detection circuit, the door switch also plays a role in belt failure detection. A failed door switch causes the dryer to either not start at all or to run continuously with the door open.
This is a Single Pole, Double Throw (SPDT) 3-wire switch with stainless steel terminals and a heat-resistant housing. It measures 1-3/4" L x 1-5/8" W x 1-1/4" H with a 7-3/4" wiring harness. Electrical specs are 120-240V, 50-60Hz, 11A, 1/3HP. The kit includes the switch and 3-wire harness assembly. It directly replaces WP3406105, 3406104, 3405104, 3405105, 528947, AP6008560, and several additional cross-reference numbers. Installs in 15–30 minutes with basic hand tools.
Quick Answer
The XPARTCO 3406105 Dryer Door Switch fixes Whirlpool-family dryers that won't start, won't stop when the door is opened, or require the door to be slammed to start. SPDT 3-wire switch, 120-240V/50-60Hz/11A/1/3HP. Body 1-3/4" L x 1-5/8" W x 1-1/4" H, 7-3/4" harness. Includes switch and harness assembly. Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, and more. Replaces WP3406105, 3406104, 3405104, 528947, AP6008560.
Common Problems This Part Fixes
Dryer will not start at all — door switch not completing the circuit when door is closed
Dryer starts only when the door is slammed or held firmly closed
Dryer continues to run after the door is opened — switch not opening the circuit
Drum light not turning on when the door is opened (on models with drum light)
Dryer starts intermittently — door switch contact worn and making unreliable contact
Dryer stops mid-cycle randomly — switch opening the circuit due to vibration or wear
Door switch visibly cracked, broken, or the actuator button no longer springs back
Replaces Part Numbers
This door switch directly replaces the following OEM and cross-reference part numbers:
WP3406105, 3405104, 3405105, 3406104, 3406105, WP3406105VP, AWP47182, PD00003898, EAP11741700, AP6008560, PS11741700.
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This door switch is compatible with select gas and electric dryers from the following brands:
Whirlpool dryers (gas and electric)
Kenmore / Sears dryers (Whirlpool-built models)
Maytag dryers (gas and electric)
KitchenAid dryers
Amana dryers
Roper dryers
Estate dryers
Crosley dryers
Inglis dryers
Admiral dryers
Jenn-Air dryers
Magic Chef dryers
Norge dryers
Always verify your appliance model number before ordering. Contact our support team if you're unsure.
Key Features
Safety switch — prevents dryer from operating when the door is open and stops the dryer immediately when the door is opened mid-cycle
Single Pole, Double Throw (SPDT) 3-wire switch — provides both normally-open and normally-closed contacts for dryer start circuit and belt failure detection on compatible models
Rated 120-240V, 50-60Hz, 11A, 1/3HP — correct electrical specifications for compatible Whirlpool-family dryers
Switch body: 1-3/4" L x 1-5/8" W x 1-1/4" H; wiring harness: 7-3/4" L
Stainless steel terminals and heat-resistant housing
Kit includes switch and 3-wire harness assembly — complete plug-in replacement
Replaces WP3406105, 3406104, 3405104, 3405105, 528947, and AP6008560
Compatible with 13 major appliance brands on the Whirlpool platform
Aftermarket replacement built to OEM-equivalent quality standards
Quick DIY repair — installs in 15–30 minutes with basic hand tools
Product Specifications
Part Number
3406105
OEM Part Number
WP3406105
Part Type
Dryer Door Switch Assembly (SPDT 3-Wire)
Condition
Aftermarket Replacement
Application
Gas and Electric Dryers
Switch Type
Single Pole, Double Throw (SPDT)
Wires
3-wire
Voltage
120-240V
Frequency
50-60Hz
Amperage
11A
Horsepower
1/3 HP
Switch Body Dimensions
1-3/4" L x 1-5/8" W x 1-1/4" H
Harness Length
7-3/4 inches
Color
Off-White / Black / Gray
Material
Plastic / Metal (stainless steel terminals)
Includes
Switch and 3-wire harness assembly
Compatible Brands
Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Estate, Crosley, Inglis, Admiral, Jenn-Air, Magic Chef, Norge
Installation Notes
⚠️ Unplug Dryer Before Starting Disconnect power (and shut off gas for gas dryers) before beginning. The door switch is located inside the dryer cabinet near the door opening, typically mounted in the front panel or top panel. Access it by inserting a putty knife under the top panel to release the spring clips and lift the top, then release the front panel. Locate the old door switch — it is a small rectangular component with a spring-loaded actuator button. Photograph the wiring connections before disconnecting. Disconnect the 3-wire harness from the old switch. Release the switch from its mounting bracket by pressing the retaining tabs and pulling the switch free, or unscrewing the mounting screw. Snap the new 3406105 switch into the mounting bracket and reconnect the 3-wire harness in the same positions. Reassemble the front and top panels, restore power, and run a test cycle to confirm the dryer starts, stops when the door is opened, and runs normally. Tools needed: Phillips screwdriver, putty knife.
Frequently Asked Questions
What does the dryer door switch do?
The door switch is a safety component that monitors whether the dryer door is open or closed. When the door is closed, the door strike depresses the switch actuator, completing the electrical circuit and signaling the control board that it is safe to run. When the door is opened, the actuator releases, opening the circuit and stopping the dryer immediately. On many Whirlpool-family dryers, the 3-wire SPDT switch also provides a secondary circuit used for broken belt detection — one of the switch's contacts is part of the motor start circuit, while the other is part of a safety cutoff circuit.
How do I test the door switch with a multimeter?
Unplug the dryer and disconnect the switch from the harness. Set your multimeter to continuity mode. The 3406105 is an SPDT switch with three terminals — typically labeled Common (C), Normally Open (NO), and Normally Closed (NC). With the actuator button not pressed (door open position), you should read continuity between C and NC, and no continuity between C and NO. With the actuator button pressed (door closed position), you should read continuity between C and NO, and no continuity between C and NC. Any deviation from this pattern confirms the switch has failed.
What is the difference between 3406105 and 3406104?
The 3406104 was the original part number, and the 3406105 (later updated to WP3406105) is the current replacement that superseded it. They are the same door switch and are fully interchangeable. The 3405104 and 3405105 are also cross-references for this same switch from earlier production. If your dryer's documentation or old switch label shows any of these numbers, the 3406105 is the correct current replacement.
Why does this switch have 3 wires when my old switch only had 2?
The WP3406105 is an SPDT (Single Pole, Double Throw) switch with 3 terminals — Common, Normally Open, and Normally Closed. Some older dryer models used a simpler 2-wire switch, but the 3-wire WP3406105 is the updated replacement that works on both older and newer models. On models that originally had a 2-wire switch, only two of the three terminals are used — the third is simply left unconnected. Follow your model's wiring diagram or take a photo of the original switch's wire connections before removing it.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured from durable plastic and metal with stainless steel terminals to match the dimensions and electrical specifications of the original WP3406105 door switch assembly.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
2304099 Refrigerator Defrost Control Board
Replaces Part Numbers: WP2304099, 2304099, 1174817, 2213100, 2213473, 2302564, 2303826, OEM24028522, AP6007130, PS11740238.
Description: This is a refrigerator control board that can be used to replace a damaged or faulty board in select refrigerators. The control board is used to manage various functions that occur in the refrigerator, including cooling and defrosting. If there is a problem with the board, the refrigerator might not be able to defrost correctly, or it might not stay cool. This control board for the refrigerator tends to last a long time. However, it could eventually wear out and stop working. It could be damaged due to a voltage surge, or it might be a faulty board. Remove and store all food in the refrigerator and unplug it before beginning repairs. This refrigerator control board works with certain models from Kenmore, Whirlpool, KitchenAid, Roper, Estate, Inglis, Crosley, Gladiator, Kirkland, and Maytag.
California Residents only
WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov
XPARTCO DC64-00828B Dryer Door Switch
The XPARTCO DC64-00828B is an aftermarket replacement dryer door switch (also called a door jamb switch) compatible with a wide range of Samsung and Kenmore Samsung-built electric and gas dryers — including the DV2, DV3, DV4, DV5, DVE, DVG, 592, 401, and 402 series. The door switch is a small safety component mounted near the dryer door frame that detects whether the door is closed. When the door closes, the switch is activated, signaling the control board that the dryer is safe to start or continue running. If the switch fails to detect the closed door, the dryer will not start, will stop mid-cycle, or in rare unsafe failure modes, may continue running with the door open.
This switch directly replaces DC64-00828A (the prior version), 2071595, AP4578931, EAP4210965, PS4210965, PS4210964, 2071594, and PD00028436. It is constructed from durable plastic and metal in white, with dimensions of approximately 1.73"L x 1.73"W x 0.47"H. Note: while this switch looks easy to remove, the front panel actually needs to come off to access it cleanly. Installs in 20–30 minutes with basic hand tools.
Quick Answer
The XPARTCO DC64-00828B Dryer Door Switch fixes Samsung and Kenmore Samsung-built dryers that won't start when the door is closed, stop mid-cycle, display error codes dC, dF, dE, or d0, or continue running with the door open. Approx. 1.73"L x 1.73"W x 0.47"H, white. Replaces DC64-00828A, 2071595, AP4578931, EAP4210965, PS4210965, PS4210964, 2071594, PD00028436. Compatible with Samsung DV2, DV3, DV4, DV5, DVE, DVG series and Kenmore 592/401/402-series dryers.
Common Problems This Part Fixes
Dryer not starting even though the door is closed
Dryer stopping mid-cycle for no apparent reason — door switch losing signal intermittently
Error codes dC, dF, dE, or d0 displayed on models with digital displays
Dryer continuing to run with the door open (unsafe failure mode — replace immediately)
Interior dryer light not turning on when the door is opened
Door switch button visibly broken, stuck, or not making the expected click when pressed
Multimeter test shows the switch fails to change state when actuated
Replaces Part Numbers
This door switch directly replaces the following OEM and cross-reference part numbers:
DC64-00828B, DC64-00828A, 2071595, AP4578931, ASM68666, EAP4210965, PD00028436, PS4210965, WP35001125, 35001125, AP6008683, PS11741823
If your part number is not listed above, contact our support team before ordering and we will verify compatibility.
Compatibility
This door switch is compatible with select Samsung and Kenmore Samsung-built electric and gas dryers, including:
Samsung dryers — DV2 series (DV203AEW, DV203AGS, DV22K6800EW, DV2C6BEW, DV2C6BGW and related)
Samsung dryers — DV3 series (DV306LEW, DV306LGW, DV316BEC, DV316BEW, DV316BGC, DV316BGW, DV316LES, DV316LEW, DV330AEB, DV330AEW, DV3C6BEW, DV3C6BGW, DV395ETPASU and related)
Samsung dryers — DV4 series (DV400EWHDWR, DV400GWHDWR, DV42H5000GW, DV45H7000EW, DV48J7770GW and related)
Samsung dryers — DV5 series (DV50K7500EW and related)
Samsung dryers — DVE series (DVE60M9900W and related electric models)
Samsung dryers — DVG series (DVG45N5300V and related gas models)
Kenmore / Sears dryers — 592, 401, and 402 series (Samsung-built models)
Always verify your appliance model number before ordering. Contact our support team if you're unsure.
Key Features
Safety switch that detects whether the dryer door is closed — required for the dryer to start and run
Direct replacement for the original equipment door switch in compatible Samsung and Kenmore dryers
Dimensions: approximately 1.73"L x 1.73"W x 0.47"H — matches original switch sizing
Durable plastic housing with metal contacts — withstands frequent door open/close cycles
Resolves Samsung door-related error codes including dC, dF, dE, and d0
Replaces DC64-00828A, 2071594, 2071595, AP4578931, EAP4210965, PS4210964, PS4210965, and PD00028436
Compatible with Samsung DV2, DV3, DV4, DV5, DVE, DVG series and Kenmore 592/401/402-series dryers
Aftermarket replacement built to OEM-equivalent quality standards
DIY repair — installs in 20–30 minutes with basic hand tools
Product Specifications
Part Number
DC64-00828B
Also Replaces
DC64-00828A (prior version)
Part Type
Dryer Door Switch (Door Jamb Switch)
Condition
Aftermarket Replacement
Application
Electric and Gas Dryers (Samsung platform)
Dimensions
Approximately 1.73"L x 1.73"W x 0.47"H
Color
White
Material
Plastic / Metal
Error Codes Resolved
dC, dF, dE, d0 (door-related)
Compatible Brands
Samsung, Kenmore (Samsung-built)
Installation Notes
⚠️ Unplug Dryer Before Starting — Wear Work Gloves Disconnect power and turn off the circuit breaker before beginning. Wear work gloves to protect your hands. Although the door switch appears easy to access from the front, on most Samsung dryer models the front panel actually needs to be removed to install the new switch cleanly. Unscrew and lift off the front panel — be careful not to drop it during reinstallation. Locate the old door switch mounted near the door frame opening. Photograph the wire connections before disconnecting. Unplug the wire harness from the old switch, release the retaining tabs or remove the mounting screws holding the switch in place, and pull it free. Install the new DC64-00828B switch in the same position, reconnect the wire harness, and reinstall the front panel. Restore power, then close the dryer door and start a cycle to confirm the door is properly detected and the dryer runs normally. Tools needed: Phillips screwdriver, work gloves.
Frequently Asked Questions
What do error codes dC, dF, dE, and d0 mean on Samsung dryers?
These door-related error codes on Samsung dryers all indicate the control board is not receiving the expected "door closed" signal from the door switch. dC and d0 commonly appear when the dryer cannot detect a closed door at the start of a cycle, while dF and dE appear when the door signal is lost during a cycle. The dryer's safety logic prevents operation under any of these conditions. Replacing a failed DC64-00828B door switch resolves these codes when the switch itself is the cause; if the codes persist after replacement, check the wiring harness between the switch and the control board for damage.
My dryer is running with the door open — what should I do?
A dryer that continues to run with the door open is a serious safety concern and should be addressed immediately. This usually indicates a failed door switch that is stuck in the "closed" position electrically, even though the door is physically open. Disconnect power to the dryer right away and avoid running it until the switch has been replaced. The DC64-00828B replacement restores normal safety behavior. Until the repair is complete, do not run the dryer.
What is the difference between DC64-00828B and DC64-00828A?
These are the same door switch across successive production revisions. DC64-00828A was the original part number and DC64-00828B is the current updated version. Both are fully interchangeable — if your dryer's parts diagram shows DC64-00828A, the DC64-00828B is the correct current replacement and is covered by this listing.
My dryer suddenly stops mid-cycle even though the door is closed — could this be the switch?
Yes — a door switch with intermittent contact failure is a common cause of unexplained mid-cycle shutdowns on Samsung dryers. The switch may be working correctly when first activated but losing its signal momentarily during operation due to vibration or worn internal contacts, causing the control board to interpret a momentary "door open" condition and stop the cycle. If this is happening repeatedly without any other identifiable cause, replacing the DC64-00828B door switch is the recommended fix.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured from durable plastic and metal to match the dimensions, switch contacts, and function of the original DC64-00828B dryer door switch.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.
✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout
XPARTCO DC96-01703G Washer Water Level Pressure Switch - Compatible with Samsung Washers
Product Description
Ensure accurate water level control in your washer with the replacement XPARTCO DC96-01703G Washer Water Level Pressure Switch. This replacement pressure switch is designed for select Samsung front-load and top-load washers, sensing and controlling water levels for optimal washing performance. It addresses issues like incorrect water levels, not filling, or error codes (e.g., E6 FA), offering a cost-effective alternative to OEM parts.
Note: Includes one water level pressure switch. Disconnect power and water supply before installation. Verify compatibility with your washer model.
Replaces part numbers: DC96-01703G, PD00026135, EAP4217083, AP5623035, PS4217083.
Compatibility:
Compatible with models including but not limited to:
Samsung: WF42H5000AW/A2, WF42H5200AP/A2, WF42H5400AF/A2, WF45K6200AW/A2, WF45K6500AW/A2, WF45M5500AP/A5, WF45M5500AZ/A5, WF50K7500AV/A2, WF50K7500AW/A2, WF56H9100AG/A2, WF56H9110CW/A2, WF457ARGSG, WW22K6800AW/A2, WV55M9600AW/A5, WV60M9900AV/A5, WD10J6410AW/ZS
Other brands: Select models requiring DC96-01703G
Verify your model number or contact our support team for assistance.
Key Features:
✅ Brand and Models Compatibility: Fits select Samsung front-load and top-load washers requiring DC96-01703G.
🔥 Specifications: Precision-engineered water level pressure switch with 28" air pressure hose, designed for accurate water level sensing and control.
💰 Cost-Effective Alternative: Offers OEM-equivalent performance at a lower price.
🛠️ Easy Installation: Requires Phillips screwdriver, work gloves; typically installed in 10–15 minutes.
🛡️ Effective Fixes: Resolves issues like incorrect water levels, not filling, motor idling, or error codes (e.g., E6 FA).
Product Specification
Part Number: XPDC96-01703G
Component Type: Washer water level pressure switch
Material: Durable plastic housing with metal contacts
Terminal Type: Electrical connector.
Operating Conditions: Suitable for high-humidity washer environments
Compliance: Prop 65 warning for California
Installation Notes:
Safety First: Disconnect the washer from the power source and water supply before installation.
Tools Needed: Phillips screwdriver, work gloves.
Process: Access the switch by removing the top or back panel of the washer, disconnect the old switch’s wiring and hose, install the new switch, and reconnect wiring and hose. Ensure secure connections and test for proper operation.
Shop for high-quality replacement appliance parts with a 30-day return policy. Keep your washer running efficiently today!
Add to cart now for a budget-friendly fix!
W10335056 Washer Genuine OEM Water Level Switch Pressure Switch
Replaces Part Numbers: W10335056, 1617123, 3366846, AH3408073, EA3408073, AP4566382, PS3408073, W10335056VP.
Description: This Pressure Switch is a Genuine OEM part for specific Whirlpool washing machine models. This part ensures your machine fills with the correct amount of water for the selected cycle, preventing overfilling or insufficient water levels that can lead to suboptimal washing results. A faulty Pressure Switch can result from several issues, including clogging with detergent residue or debris, wear and tear from regular use, or electrical malfunctions affecting its responsiveness.
California Residents only
WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov
