Dishwasher Parts

A00126501CM Dishwasher Drain Pump 120V, 60 Hz, 0.8A, 35W 3600 RPM. Fits Electrolux dishwashers. Replaces Part Number:  A00126501, 154640201, 154474101, 3019314, OEM17071301, AP5690432, PS8689825, B08CY4Q6DZ Description: This Drain Pump Assembly is a replacement part for specific Frigidaire, Kenmore dishwasher models. It is responsible for removing water from the dishwasher tub during the drain cycle, ensuring that water is properly expelled to complete the washing process. Common causes of a bad drain pump assembly include clogs from debris or food particles, electrical issues like a burnt-out motor, or damage due to improper installation or handling. This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

Genuine GE OEM Part GE WD24X25325 Dishwasher Genuine Fan Vent Assembly Genuine GE door-vent blower/fan assembly for select GE and Haier dishwashers. Product Overview The GE WD24X25325 Dishwasher Fan Vent Assembly is a genuine OEM replacement used in the dishwasher door ventilation system. The blower circulates air through the door vent during the drying portion of the cycle to help reduce retained moisture and improve drying performance. Quick Answer WD24X25325 is a Genuine GE OEM dishwasher door-vent blower/fan motor assembly. It is used on select GE and Haier dishwashers and helps move moist air through the door vent during drying. Common Problems This Part May Fix Poor drying performance Excess moisture remaining after a cycle Door vent fan does not run Unusual noise from the vent/blower area Moist air is not being exhausted through the door vent Replaces and Cross-References WD24X25325, 265D2664G005, U40G12BS3A5-51, AGE25072, AP6972063, EAP12726435, PD00073154, PS12726435. Cross-reference numbers are supplied for identification. Always verify the complete dishwasher model number before ordering. Compatibility Fits select GE and Haier dishwashers. Compatible model examples include: CDT800P2N0S1 CDT805P2N0S1 CDT845P2N3S1 DDT700SBN0TS GDF645SSN0SS GDT645SFN3DS GDT665SFN0DS GDP665SYN3FS PDT715SYN2FS PDT715SFN0DS PDP715SYN3FS QDP555SYN0FS Important: This is only a partial compatibility list. Confirm the exact dishwasher model number before purchase because similar models may use a different vent or blower assembly. Key Features Genuine GE Appliances OEM part Complete door-vent blower/fan assembly Circulates air through the dishwasher door vent Helps reduce moisture during drying For select GE and Haier dishwashers Product Specifications Manufacturer GE Appliances Manufacturer Part Number WD24X25325 Part Type Dishwasher Fan Vent / Door Vent Blower Assembly Condition New Part Quality Genuine OEM Application Dishwasher Door Ventilation / Drying System Approx. Shipping Weight 0.5 lb Installation Notes Disconnect electrical power to the dishwasher at the breaker before service. Access the door vent assembly according to the appliance service procedure. Disconnect the wiring connector carefully before removing the old fan assembly. Transfer or reuse any hardware only as directed for the specific model. Confirm the vent path is clear and the new assembly is fully seated before reassembly. Diagnostic note: Poor drying can also result from rinse-aid settings, heating-system faults, blocked vent passages, or control issues. Confirm the fan assembly is defective before replacing it. Frequently Asked Questions Is WD24X25325 a Genuine GE OEM part? Yes. GE Appliances identifies WD24X25325 as a genuine replacement fan vent assembly. What does this fan assembly do? It circulates air through the dishwasher door vent to help reduce moisture during the drying stage. Does it fit every GE dishwasher? No. It fits specific GE and Haier models. Verify the complete model number before ordering. Is this only the fan motor? This listing is for the complete WD24X25325 fan vent / door-vent blower assembly as supplied by GE. Shop With Confidence Use your dishwasher's complete model number to confirm fitment before purchase. Genuine GE OEMFan Vent AssemblyModel Verification RecommendedFast U.S. Shipping

Read more less

Genuine Bosch OEM Bosch 00640476 Dishwasher Genuine OEM Terminal Box Original Bosch dishwasher terminal box with terminal block for select Bosch, Thermador, Gaggenau, and Kenmore dishwashers. Product Overview The Bosch 00640476 Dishwasher Terminal Box is a genuine OEM electrical connection enclosure used on compatible dishwashers. It houses the terminal block where household electrical power connects to the dishwasher wiring harness. This assembly is supplied with the terminal block. The separate wiring/terminal-box cover is not included; Bosch identifies the matching cover as part 00640477. Quick Answer 00640476 is a Genuine Bosch OEM dishwasher terminal box with terminal block. It replaces earlier part 640476. The cover is sold separately as 00640477. Common Problems This Part May Fix Dishwasher will not start because of a damaged power connection Burned, overheated, or melted terminal connections Loose or damaged line-voltage wiring connection Damaged terminal block or terminal-box housing Intermittent power caused by compromised terminal connections Replaces and Cross-References 00640476, 1378543, 640476, ABS11577, AP3962500, EAP8729475, PD00023793, PS8729475 Cross-reference numbers are provided for identification. Bosch 00640476 is the Genuine OEM part. Compatibility Used on select Bosch-built dishwashers sold under Bosch, Thermador, Gaggenau, and Kenmore brands. Verified model examples include: SHE55C05UC/58 SHE43F15UC/61 SHE4AM16UC/02 SHX3AM06UC/01 SHX3AR56UC/07 S36KMK15UC/05 DWHD410HPR/60 63013903010 63013909012 Important: This is only a partial compatibility list. Bosch uses E-Nr./model revisions, so verify the complete model number including the suffix before ordering. Key Features Genuine Bosch OEM replacement part Includes terminal box and terminal block Connects household electrical power to dishwasher wiring Replaces Bosch part 640476 For select Bosch-built dishwasher platforms Cover 00640477 is sold separately Product Specifications Manufacturer Part Number 00640476 Manufacturer Bosch Part Type Dishwasher Terminal Box / Terminal Block Assembly Condition New Part Quality Genuine OEM Terminal Block Included Yes Cover Included No Matching Cover 00640477, sold separately Application Select Bosch-built dishwashers Installation Notes Shut off the dishwasher circuit breaker and verify power is off before beginning service. Remove the lower access panel as required for the model. Photograph and label existing wire connections before disconnecting them. Inspect supply wiring and the dishwasher harness for heat damage, burned insulation, or loose conductors. Transfer wiring to the new terminal block according to the dishwasher wiring diagram and installation instructions. Secure strain relief and wiring so no bare conductor is exposed. Install the proper terminal-box cover before restoring power. Electrical safety: This part carries household line voltage. If wiring is burned, melted, or damaged, correct the underlying connection problem and replace damaged wiring as required. Installation should be performed by a qualified person when local electrical codes or conditions require it. Frequently Asked Questions Is 00640476 a Genuine Bosch OEM part? Yes. It is manufactured by Bosch as an original equipment replacement terminal box. Does this include the terminal block? Yes. Bosch describes 00640476 as a terminal box with terminal block. Is the cover included? No. The matching wiring/terminal-box cover is Bosch part 00640477 and is sold separately. Does 00640476 replace 640476? Yes. 640476 is the earlier Bosch part number superseded by 00640476. Will it fit every Bosch dishwasher? No. Compatibility depends on the full Bosch E-Nr./model and revision. Verify the complete model number before purchase. Shop With Confidence Use the complete dishwasher model or E-Nr. to confirm fitment before ordering. Genuine Bosch OEM construction helps ensure the correct electrical connection design for compatible models. Genuine Bosch OEMTerminal Block IncludedCompatibility SupportNew Part

Read more less

Genuine Frigidaire OEM Part 5304533992 Dishwasher Control Panel Housing Console Assembly Genuine OEM Frigidaire console housing/overlay assembly for select Frigidaire dishwashers. No electronics included. Product Overview The Frigidaire 5304533992 Dishwasher Console Assembly is the exterior control-panel housing and overlay used on select Frigidaire dishwashers. It provides the finished front console surface and secure mounting location for the user-interface components. This is a Genuine Frigidaire OEM part manufactured for exact fit on compatible models. Quick Answer 5304533992 is the genuine OEM dishwasher console housing/overlay assembly that replaces 5304532797. This part does NOT include the electronic user-control/display board. On compatible models, the separate switch/display assembly is part 5304532245. Common Problems This Part May Fix Control panel housing is cracked or broken Console is warped or will not mount securely Button/overlay area is physically damaged Display or switch board will not stay properly mounted because the housing is damaged Cosmetic damage to the front control console Replaces and Cross-References 5304533992, 5304532797, AP7204637, EAP16763567, FIX16763567, OEM21613920, PS16763567, AFR20138, PD00090155 Cross-reference numbers identify the same console housing assembly through manufacturer and parts-catalog systems. Compatibility Confirmed for select Frigidaire 24-inch dishwashers, including: GDPH4515AD0A GDPH4515AD1B GDPH4515AF0A GDPH4515AF1B GDPP4515AF0A GDPP4515AF1B Important: Confirm the complete dishwasher model number before ordering. Similar-looking control consoles can differ in overlay, mounting points, and electronics compatibility. Key Features Genuine Frigidaire OEM replacement part Console housing with control-panel overlay Replaces 5304532797 Restores secure mounting for the control interface Factory-fit appearance for compatible Frigidaire dishwashers No electronic control board included Product Specifications Manufacturer Part Number 5304533992 Brand Frigidaire Part Type Dishwasher Console / Control Panel Housing Assembly Condition New Part Quality Genuine OEM Electronics Included No Replaces 5304532797 Compatible Appliance Dishwasher Quantity 1 Console Assembly Important — No Electronics Included This listing is for the console housing/overlay assembly only. It does not include the user-control/display board, main control board, wiring harness, or other electronic components unless specifically shown and stated. For models using this console, the separate tactile switch/user-interface assembly is commonly part 5304532245. Diagnose the dishwasher before ordering: a non-responsive display or buttons may be caused by electronics rather than the plastic console housing. Installation Notes Disconnect dishwasher power at the breaker before service. Open the door and remove the fasteners required to access the console area. Photograph connector positions before disconnecting any electronic components. Transfer the existing user-interface/display components into the new console housing as required by the service procedure. Confirm all tabs, screws, seals, and connectors are properly seated. Reassemble the door before restoring electrical power. Frequently Asked Questions Does this include the electronic control board? No. 5304533992 is the console housing/overlay assembly. Electronic boards are separate parts. Does this replace 5304532797? Yes. 5304533992 is the current replacement for 5304532797. Is this Genuine OEM? Yes. This is a Genuine Frigidaire OEM replacement part. Will it fit every Frigidaire dishwasher? No. Verify the complete model number before ordering. Shop With Confidence Genuine OEM replacement part for select Frigidaire dishwashers. Verify your full model number and confirm whether your repair requires the console housing, user-interface board, or both. Genuine Frigidaire OEMNo Electronics IncludedCompatibility SupportFast U.S. Shipping

Read more less

WPW10327249 Genuine OEM Whirlpool Dishwasher Water Valve The WPW10327249 is a genuine Whirlpool OEM water inlet valve for Whirlpool, Kenmore, KitchenAid, and Maytag dishwashers, mounted on the right-hand side of the dishwasher's interior behind the front kick plate. This valve regulates the flow of water into the appliance during each cycle, opening to admit water from the household supply and closing once the correct amount has entered, which is essential to proper filling and efficient operation. Over time, mineral or sediment buildup inside the valve body, or general electrical wear in the solenoid, can cause the valve to fail. A failing valve produces a clear set of symptoms: the dishwasher not filling with water at all, water filling inconsistently or too slowly, leaking, or overfilling. It directly replaces AP6019618, W10316814, W10327249, W11130743, WPW10327249VP, 3015511, PS11752927, and W11669945. Quick Answer The WPW10327249 Genuine OEM Whirlpool Dishwasher Water Valve fixes Whirlpool, Kenmore, KitchenAid, and Maytag dishwashers that won't fill with water, fill inconsistently, leak, or overfill. Located on the right-hand side of the dishwasher interior. Replaces W10327249, W10316814, W11130743, 3015511, WPW10327249VP, AP6019618, AWP49829, PD00002758, PS11752927. While the dishwasher is disassembled for this repair, consider also checking or replacing the water supply adapter (W10685193), since it's in the same area and easy to inspect at the same time. Common Problems This Part Fixes Dishwasher not filling with water at all Water filling inconsistently or too slowly Dishwasher leaking near the valve area Dishwasher overfilling Cycle stalling at the fill step and never advancing to wash Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dishwasher water valve directly replaces the following OEM and cross-reference part numbers: WPW10327249, W10327249, W10316814, W11130743, 3015511, WPW10327249VP, AP6019618, AWP49829, PD00002758, PS11752927 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water valve is compatible with select Whirlpool dishwashers, and also fits select Kenmore, KitchenAid, and Maytag dishwashers built on the Whirlpool platform, including model numbers such as WDT750SAHZ, WDTA50SAHZ, WDT710PAYM, MDB4949SDM, and MDB4949SHZ. Note: Always verify your full model number before ordering, since similar-looking dishwasher water valves can vary in size or shape between models. Contact our support team with your model number if you're unsure. Key Features Genuine Whirlpool OEM part — factory-specified solenoid design and flow rate Regulates water flow into the dishwasher during each fill cycle Resolves "won't fill," "fills inconsistently," "leaking," and "overfilling" symptoms caused by valve failure Direct drop-in replacement — matches the original mounting and hose connections Replaces W10327249, W10316814, W11130743, 3015511, WPW10327249VP, AP6019618, AWP49829, PD00002758, PS11752927 Compatible with Whirlpool, Kenmore, KitchenAid, and Maytag dishwashers Genuine OEM replacement — guaranteed fit, materials, and performance Novice-friendly repair with basic hand tools Product Specifications Part Number WPW10327249 Part Type Dishwasher Water Inlet Valve Condition Genuine OEM Brand Whirlpool Location Right-hand side of the dishwasher interior, behind the front kick plate Color Blue Water Line Connections Two 3/8" lines Repair Difficulty Medium — basic appliance repair skills Quantity 1 valve Compatible Brands Whirlpool, Kenmore, KitchenAid, Maytag Installation Notes ⚠️ Unplug Dishwasher And Shut Off Water Supply Before Starting Disconnect power at the outlet or shut off the circuit breaker, and shut off the water supply at the shutoff valve located behind the dishwasher before beginning. Wear work gloves. Remove the bottom front kick plate by pulling outward on the two clips located at either side of the bottom panel. Locate the water inlet valve on the right-hand side of the dishwasher interior. Disconnect the two 3/8" water lines from the old valve. Unscrew the mounting screws holding the valve in place, and carefully pull the old valve away from the dishwasher. Insert the new WPW10327249 into the dishwasher, making sure it's securely positioned, and secure it with the mounting screws. Reconnect both water lines to the new valve. While you're in this area, it's worth inspecting the water supply adapter for wear, since it's a related part in the same location that's easy to check while everything is already accessible. Turn the water supply back on and plug the dishwasher back into the power source. Run a test cycle to confirm the dishwasher fills correctly with no leaks. Tools needed: multi-screwdriver, standard pliers, adjustable wrench, work gloves. Frequently Asked Questions My dishwasher isn't filling with water at all. Is this the right part? Yes, this is the most direct symptom of a failed water inlet valve. Since this valve is what admits water from your household supply into the dishwasher, a solenoid failure or internal blockage can prevent any water from entering at all, stopping the wash cycle from proceeding. Should I check or replace the water supply adapter while I have the dishwasher open? It's a reasonable idea, since the water supply adapter is a related component located in the same general area and is easy to inspect while you already have access. It doesn't need to be replaced automatically, but checking its condition at the same time can save you from needing to open the dishwasher back up again soon after if it's also showing wear. My dishwasher is leaking near the valve. Could hard water be a factor? Yes, mineral and sediment buildup from hard water is a common contributor to valve failure over time, since it interferes with the valve's ability to seal and shut off properly. Using a dishwasher cleaner periodically to help reduce limescale buildup can support the longevity of the new valve, though it isn't a substitute for replacing a valve that has already failed. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original solenoid design, flow rate, and connection type of the water inlet valve originally installed in your dishwasher. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WPW10605057 Genuine OEM Whirlpool Dishwasher Pump & Motor Assembly The WPW10605057 is a genuine Whirlpool OEM circulation pump and diverter motor assembly for Whirlpool, Kenmore, KitchenAid, Jenn-Air, Maytag, Amana, Magic Chef, Admiral, Norge, Roper, and Ikea dishwashers. This assembly pumps water up through the spray arms throughout the wash cycle, and the integrated diverter motor controls which spray arm receives that water at any given moment. This assembly includes the circulation pump and diverter motor only — it does not include the drain pump, which is a separate component on this platform. Over time, the pump motor's internal windings can wear out or fail electrically, or the diverter mechanism can stick or bind. A failing assembly typically shows up as a dishwasher that isn't washing dishes properly because water isn't circulating through the spray arms, or leaking from underneath the unit. Whirlpool's own guidance recommends checking the motor's resistance with a multimeter if water isn't circulating, to confirm the assembly before replacing it. It directly replaces AP6023350, WPW10482502, W10482502, W10605057, 3021439, 3023239, PS11756692, W10236194, W10534160N, W10300740, and W10500285. Quick Answer The WPW10605057 Genuine OEM Whirlpool Dishwasher Pump & Motor Assembly fixes Whirlpool, Kenmore, KitchenAid, Jenn-Air, Maytag, Amana, Magic Chef, Admiral, Norge, Roper, and Ikea dishwashers that aren't washing dishes properly because water isn't circulating, or that are leaking from underneath. Includes the circulation pump and diverter motor — not the drain pump. Replaces WPW10482502, W10482502, W10605057, 3023239, W10300740, W10500285, AP6023350, AWP51141, PD00026666, PS11756692. Check the motor's resistance with a multimeter before replacing to confirm this assembly is actually the cause. Common Problems This Part Fixes Dishes not getting clean because water isn't circulating through the spray arms Dishwasher leaking from underneath the unit Weak or absent water spray during the wash cycle Motor humming without spraying water normally Inconsistent washing results from cycle to cycle Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dishwasher pump and motor assembly directly replaces the following OEM and cross-reference part numbers: WPW10605057, WPW10482502, W10482502, W10605057, 3023239, W10300740, W10500285, AP6023350, AWP51141, PD00026666, PS11756692. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This pump and motor assembly is compatible with select Whirlpool dishwashers, and also fits select Kenmore, KitchenAid, Jenn-Air, Maytag, Amana, Magic Chef, Admiral, Norge, Roper, and Ikea dishwashers built on the Whirlpool platform, including model numbers such as KDTE104ESS, WDT710PAHZ, KDFE104DSS, WDT780SAEM, and WDT710PAHB. Note — circulation pump only, not the drain pump: This assembly includes the circulation pump and diverter motor. The drain pump on this platform is a separate component and is not included with this assembly. If your dishwasher isn't draining rather than not washing properly, you likely need the drain pump instead. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure which part your dishwasher needs. Key Features Genuine Whirlpool OEM part — factory-specified pump and diverter motor design Includes the circulation pump and diverter motor, which controls spray arm water flow Resolves "not washing properly," "water not circulating," and "leaking underneath" symptoms Factory Certified Part built to Whirlpool's engineering specifications Direct drop-in replacement — matches the original mounting and hose connections Replaces WPW10482502, W10482502, W10605057, 3023239, W10300740, W10500285, AP6023350, AWP51141, PD00026666, PS11756692 Compatible with Whirlpool, Kenmore, KitchenAid, Jenn-Air, Maytag, Amana, Magic Chef, Admiral, Norge, Roper, and Ikea dishwashers Genuine OEM replacement — guaranteed fit, materials, and performance DIY-friendly repair, typically about 30 minutes Product Specifications Part Number WPW10605057 Part Type Dishwasher Circulation Pump & Diverter Motor Assembly Condition Genuine OEM Brand Whirlpool Function Circulates water through the spray arms; diverter motor controls spray arm flow Includes Drain Pump No — sold separately Repair Difficulty Moderate — approx. 30 minutes Quantity 1 pump and motor assembly Compatible Brands Whirlpool, Kenmore, KitchenAid, Jenn-Air, Maytag, Amana, Magic Chef, Admiral, Norge, Roper, Ikea Installation Notes ⚠️ Unplug Dishwasher And Shut Off Water Supply Before Starting Disconnect power at the outlet or shut off the circuit breaker, and shut off the water supply before beginning. Wear work gloves. Remove the lower dish rack, the impeller/spray arm, and the drain filter to access the interior floor of the tub. Working from underneath the dishwasher, release the drain hose from the pump using pliers, then hand-unscrew the drain pump and temperature sensor about a quarter-turn each, being careful to release the small clip holding the drain pump in place — leave both of these components in place, since they're not part of this replacement. Release the three levers that clamp the pump and motor assembly to the bottom of the dishwasher, positioned roughly at 0, 120, and 240 degrees around the assembly. Photograph the electrical connections before disconnecting anything, since keeping track of exactly how everything was wired makes reassembly straightforward. Pop the old assembly up and out through the bottom of the dishwasher. If your old assembly used a separate counterweight, transfer it to the new assembly. Install the new WPW10605057 assembly through the same opening, reconnect all electrical connections exactly as photographed, and re-engage the three clamping levers. Reconnect the drain pump, temperature sensor, and drain hose you set aside earlier. Reinstall the drain filter, spray arm/impeller, and lower rack. Restore water and power, then run a test cycle to confirm normal water circulation with no leaks underneath. Tools needed: multi-screwdriver, pliers, work gloves. Frequently Asked Questions My dishwasher isn't cleaning dishes well. How do I know if this is the right part? Whirlpool's own guidance recommends checking the pump motor's resistance with a multimeter first if water isn't circulating properly. If the motor tests outside its expected resistance range, or shows no continuity at all, that confirms this assembly has failed and needs replacing rather than a different component being at fault. Should I replace the drain pump at the same time? Not necessarily — this assembly doesn't include the drain pump, and if your dishwasher is washing normally but just not draining, the drain pump (a separate part) is the more likely cause rather than this circulation assembly. If both symptoms are present, it's worth checking both components, but they aren't sold together in this listing. Do I need to replace the counterweight or reuse the old one? If your dishwasher's original assembly used a separate counterweight component, transfer it from the old assembly to the new one during installation rather than assuming a new one is included. Check your specific model's parts diagram if you're not sure whether this applies to your dishwasher. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original pump design, diverter motor function, and mounting configuration of the circulation pump and motor assembly originally installed in your dishwasher. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WD08X23477 Genuine OEM GE Dishwasher Tub Seal Gasket The WD08X23477 is a genuine GE OEM tub seal gasket designed specifically for GE dishwashers with a stainless steel tub. This gasket runs around the tub opening and creates the seal that keeps wash water contained inside the tub during the cycle rather than leaking out around the edges where the tub meets the door and surrounding cabinet structure. Over time, this seal can flatten, harden, or develop gaps from years of heat and moisture exposure, which lets water escape past the seal instead of staying inside the tub. A worn or damaged gasket typically shows up as water leaking from underneath or around the front of the dishwasher during a cycle, dampness or pooling near the base of the unit, or visible flattening, cracking, or separation in the seal material itself. It directly replaces AP6041570 and PS11774413. Quick Answer The WD08X23477 Genuine OEM GE Dishwasher Tub Seal Gasket fixes GE dishwashers with a stainless steel tub that are leaking water from around the tub opening during a cycle. Replaces AP6041570, PS11774413. This gasket is specific to stainless steel tub models — it is not the plastic tub/door gasket used on other GE dishwasher designs, such as WD08X21894 or WD08X23476. Common Problems This Part Fixes Water leaking from underneath or around the front of the dishwasher during a cycle Dampness or pooling near the base of the dishwasher after running Visible flattening, hardening, or cracking of the seal around the tub opening Gaps or separation in the gasket where it meets the tub frame Leak that appears intermittently, worse on longer or hotter cycles Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dishwasher tub seal gasket directly replaces the following OEM and cross-reference part numbers: WD08X23477, WD08X22095, WD08X20675, 4466531, WD08X20591, AGE24098, AP6041570, EAP11774413, PD00052582, PS11774413 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This tub seal gasket is compatible with select GE dishwashers equipped with a stainless steel tub, and also fits select Hotpoint, Haier, Monogram, and Café dishwashers built on the same GE platform. Note — stainless steel tub only, and verify fit carefully: This gasket is designed specifically for GE's stainless steel tub design and is a different part from the gaskets used on plastic tub GE dishwashers (such as WD08X21894 or WD08X23476). Additionally, this seal has a documented fitment sensitivity — at least one customer has reported that on their unit, the older original seal had roughly 2 extra inches of material at the bottom that this replacement did not match, resulting in a persistent minor leak even after installation. Confirm your dishwasher has a stainless steel tub and verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine GE OEM part — factory-specified for stainless steel tub dishwashers Seals the tub opening to keep wash water contained during the cycle Resolves "water leaking from the front or underneath," "dampness near the base," and "flattened or cracked seal" symptoms Durable material designed to withstand repeated high-humidity, high-temperature cycles Direct drop-in replacement — fits the original tub opening groove Replaces AP6041570 and PS11774413 Compatible with GE, Hotpoint, Haier, Monogram, and Café stainless steel tub dishwashers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number WD08X23477 Part Type Dishwasher Tub Seal Gasket Condition Genuine OEM Brand GE Application Stainless Steel Tub Dishwashers Function Seals the tub opening to prevent water leaks during wash cycles Quantity 1 tub seal gasket Compatible Brands GE, Hotpoint, Haier, Monogram, Café Installation Notes ⚠️ Unplug Dishwasher And Shut Off Water Before Starting — Verify Seal Length Against Your Original Disconnect power at the outlet or shut off the circuit breaker, and shut off the water supply before beginning. Wear work gloves. Access to the tub opening seal is typically from the front of the unit with the door open, though some models may require removing the door or surrounding trim to fully access the gasket channel. Before removing the old seal, take note of its full length and how it seats into the groove around the tub opening — some customers have found the replacement seal shorter than the original at one section, so compare the two side by side before discarding the old one. Carefully pull the old gasket free from its retaining groove, working around the full perimeter. Press the new WD08X23477 gasket into the same groove, working around the full perimeter and ensuring it seats evenly with no twists, gaps, or areas where it's pulled too tight. Run your fingers along the full seal after installation to confirm even, consistent contact with no visible gaps. Restore water and power, then run a test cycle and check underneath and around the front of the unit for any signs of leaking. Tools needed: flat-blade screwdriver (model-dependent access), work gloves. Frequently Asked Questions How do I know if my dishwasher has a stainless steel tub or a plastic tub? Open the dishwasher door and look at the interior tub walls — a stainless steel tub has a visible metallic finish, while a plastic tub is typically a solid plastic color (often white, gray, or black) with no metallic sheen. This gasket is designed specifically for the stainless steel tub design; plastic tub models use a different gasket. If you're not sure, check your model number against your appliance's documentation or contact our support team. I installed the new seal but I'm still seeing a small leak. What should I check? This has been reported by at least one customer, who found their original seal had extra material at the bottom that this replacement didn't fully match, resulting in a persistent minor leak. Before assuming the gasket itself is faulty, run your fingers around the entire seal after installation to check for any spot where it isn't making even, firm contact — pay particular attention to the bottom section. If a specific area isn't sealing, it may need to be pressed more firmly into its groove, or in rare cases, your particular tub design may require a different seal than expected. Contact our support team with your model number if the leak persists after a careful reinstall. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by GE to factory specifications — guaranteed fit, materials, and performance. It matches the original material, profile, and groove fit of the tub seal gasket originally installed in your stainless steel tub dishwasher. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

00770657 Genuine OEM Bosch Dishwasher Silverware / Cutlery Drawer The 00770657 is a genuine Bosch OEM cutlery drawer — a dedicated third-rack silverware caddy that sits in the upper interior of the dishwasher tub, above the top rack, on select Bosch dishwashers equipped with a third rack add-on compartment. Rather than loading silverware into a basket down in the lower rack, this drawer holds forks, spoons, and knives flat in their own dedicated level, laid out individually with room around each piece so water and detergent can reach every surface. It rides on durable rollers along rails built into the tub, sliding smoothly in and out for loading and unloading, and its position at the top of the tub gives it a clear, unobstructed line to the upper spray arm for targeted cleaning. The tray and support grid inside the drawer are open enough to let water flow freely through while still keeping utensils separated and organized. Because it's a lightweight tray sitting in a hot, wet, chemically active environment for years, common failure points include a metal frame that rusts through and eventually collapses under its own weight, plastic that becomes brittle or begins visibly disappearing from years of heat exposure, and dividers that crack or break, letting silverware jumble together. It directly replaces AP5788109, 00689507, 3279853, and PS8747441. As a genuine OEM part, the 00770657 is manufactured by Bosch to factory specifications — guaranteed fit, materials, and performance. Quick Answer The 00770657 Genuine OEM Bosch Dishwasher Silverware / Cutlery Drawer fixes Bosch (and compatible Thermador, Gaggenau, and select Kenmore) dishwashers with a third-rack cutlery drawer that has rusted through, has cracked or broken dividers, has become gummy or sticky and won't slide smoothly, or has cracks exposing silverware to the heating element below. Rides on rollers for smooth in-and-out extension. Replaces AP5788109, 00689507, 3279853, PS8747441. This is the roller-equipped cutlery drawer — a similar-looking companion part, 00770656, is a different drawer design without rollers, so double-check which one your dishwasher uses. Common Problems This Part Fixes Metal frame of the cutlery drawer rusted through or visibly corroding Drawer frame collapsing or sagging under the weight of silverware Missing or broken dividers letting silverware commingle instead of staying separated Drawer glides that have become gummy or sticky from food residue buildup, obstructing smooth movement Cracks or holes in the drawer exposing silverware to direct contact with the heating element Plastic that has become brittle, discolored, or is visibly disappearing after years of heat exposure Silverware not getting fully clean due to poor spray coverage from a warped or damaged drawer Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dishwasher cutlery drawer directly replaces the following OEM and cross-reference part numbers: 00770657, AP5788109, 00689507, 3279853, ABS12031, EAP8747441, PD00043732, PS8747441 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This cutlery drawer is compatible with select Bosch dishwashers equipped with a third rack add-on compartment, and is also compatible with Thermador, Gaggenau, and select Kenmore dishwashers configured with a triple-rack setup, including model numbers such as: SHE68T52UC, SHE68T55UC, SHE68T56UC, SHE68TL5UC SHE863WF5N, SHE863WF6N SHP65T56UC, SHP65TL2UC SHV68T53UC, SHV68TL3UC, SHV863WD3N SHVM63W53N, SHXM63W55N, SHXM63WS5N Each of these models spans multiple production suffixes (such as /01, /02, /07, and /09) — check your full model and production number for exact confirmation. Note — check for rollers: This drawer rides on rollers. A similar-looking companion part, 00770656, is a separate cutlery drawer design used on other Bosch/Thermador/Gaggenau models without the roller mechanism. The two are not interchangeable. Check whether your existing drawer slides on visible rollers before ordering, and always verify your full model and production number. Contact our support team with your model number if you're unsure which drawer fits your dishwasher. Key Features Genuine Bosch OEM part — factory-specified frame, grid, and roller mechanism Dedicated third-rack cutlery drawer positioned above the top rack for optimal spray-arm targeting Resolves "rusted frame," "broken dividers," "sticky glides," and "cracked drawer" symptoms caused by wear and corrosion Multi-level basket layout keeps silverware separated for full surface exposure to wash spray Rides smoothly on rollers for easy extension and retraction when loading and unloading Open tray and support grid design allows water and detergent to flow through freely Direct drop-in replacement — no tools required, simply slides into place on existing rails Replaces AP5788109, 00689507, 3279853, and PS8747441 Compatible with Bosch, Thermador, Gaggenau, and select Kenmore third-rack dishwashers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number 00770657 Part Type Dishwasher Third-Rack Cutlery / Silverware Drawer Condition Genuine OEM Brand Bosch Location Upper interior of the tub, above the top rack Mounting Rides on rollers along built-in tub rails Design Multi-level basket grid with open tray for water flow Repair Difficulty Very Easy — no tools required Quantity 1 cutlery drawer Compatible Brands Bosch, Thermador, Gaggenau, select Kenmore Installation Notes This is one of the simplest repairs in the entire dishwasher — no tools, no wiring, and no water lines to disconnect. Open the dishwasher door fully. Locate the existing cutlery drawer at the top of the tub, above the upper rack, and slide it forward and out along its rails until it clears the cabinet. Line up the new 00770657 drawer with the same rollers and rails, and slide it in until it seats fully at the back of the tub. Close the door and run a cycle to confirm the drawer sits securely and doesn't rattle or shift during operation. Frequently Asked Questions Does my drawer use rollers, or is it the other style? Slide your existing drawer out partway and look underneath or along the sides — this 00770657 drawer rides on visible roller wheels along the tub rails. If your drawer instead has a simpler glide track with no rollers, you likely have the companion part, 00770656, which is a different design used on other models. The two aren't interchangeable, so it's worth confirming before ordering. My drawer's metal frame has rusted through. Is that just cosmetic, or should I replace it? It's worth replacing rather than living with it. Once the metal frame starts rusting through, it typically continues to weaken and can eventually collapse under the weight of loaded silverware, sometimes suddenly. Customers who've dealt with this describe the original frame rusting to the point of failure over time — replacing it before it fully gives out avoids a mid-cycle collapse and keeps your utensils properly organized and exposed to the wash spray. Do I need any tools to install this? No. This is a genuinely tool-free repair — slide the old drawer out along its rails, then slide the new one in until it seats. Customers consistently describe this as one of the easiest dishwasher parts to swap. I see cracks or holes in my drawer near the bottom. Is that a safety concern? It can be, depending on where the damage is. If cracks or holes are positioned where silverware could shift down and make direct contact with the dishwasher's heating element, that's worth addressing rather than ignoring, since it can affect both the cleaning process and the condition of your utensils over repeated cycles. Replacing a cracked or holed drawer resolves this. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Bosch to factory specifications — guaranteed fit, materials, and performance. It matches the original roller mechanism, basket grid layout, and dimensions of the cutlery drawer originally installed in your third-rack-equipped Bosch, Thermador, Gaggenau, or compatible Kenmore dishwasher. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

WD14X10009 Genuine OEM GE Dishwasher Hinge Arm Link The WD14X10009 is a Genuine OEM GE replacement dishwasher hinge arm link compatible with an exceptionally wide range of GE, GE Profile, Café, Monogram, Hotpoint, RCA, Haier, and Kenmore GE-built dishwashers — it fits over 2,100 models. The hinge arm link is the small plastic connector that joins the door spring to the door hinge arm at the bottom of the dishwasher door. This tiny part carries a big load: it's what allows the spring to counterbalance the weight of the door — especially when the door is open with a fully loaded lower rack resting on it. Without an intact link, the spring can't do its job, and the door drops open under its own weight instead of lowering in a smooth, controlled motion. The hinge arm link is a small piece of white plastic approximately 1-1/2" long, weighing about 0.01 lbs. It fails from ordinary wear and tear — thousands of open/close cycles gradually stress the plastic until it cracks or snaps. As a Genuine OEM part manufactured by GE to factory specifications, the WD14X10009 directly replaces AP2039321, 270839, AH259336, EA259336, and PS259336. Important: your dishwasher has a door spring and hinge arm link on BOTH the left and right sides. This part is sold individually — if one link has broken from age, the other is the same age and often not far behind, so many customers order two and replace both while the dishwasher is pulled out. Installs in 15–30 minutes with basic hand tools. Quick Answer The WD14X10009 Genuine OEM GE Dishwasher Hinge Arm Link fixes GE, GE Profile, Café, Monogram, Hotpoint, RCA, Haier, and Kenmore dishwashers where the door falls open instead of lowering gently, the door won't stay shut or won't latch, the door is hard to open or close, or the door slants when open. Small white plastic link ~1-1/2" long — connects the door spring to the door hinge arm. Genuine OEM. Sold individually. Replaces AP2039321, 270839, AH259336, EA259336, PS259336. Fits 2,100+ GE-platform dishwasher models. There's one link on EACH side of the door — consider ordering two. Common Problems This Part Fixes Dishwasher door falls open instead of lowering in a smooth, controlled motion — no counterbalance from the spring Door drops down hard when opened — link broken, spring disconnected Door won't stay shut, or opens unexpectedly Door won't latch or lock properly Door is difficult to open or close Door slants or hangs unevenly when open Hinge arm link visibly cracked, bent, broken, or significantly worn Broken plastic link found lying on the floor beneath the dishwasher Door spring disconnected and hanging loose Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dishwasher hinge arm link directly replaces the following OEM and cross-reference part numbers: WD14X10009, AGE24269, AP2039321, 270839, AH259336, EA259336, EAP259336, PD00023035, PS259336 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This hinge arm link is compatible with an exceptionally broad range of dishwashers — over 2,100 models across the following brands: GE dishwashers — the vast majority of GE dishwasher models across many generations GE Profile dishwashers (including PDW-series models) Café dishwashers (select models) GE Monogram dishwashers (select models) Hotpoint dishwashers (select models) RCA dishwashers (select GE-built models) Haier dishwashers (select GE-platform models) Kenmore / Sears dishwashers (select GE-built models) Important — There Are TWO Links, One Per Side: Your dishwasher door has a spring and hinge arm link on both the left and right sides. This part is sold individually. Many customers discover the second link only after reinstalling the dishwasher — and since both links are the same age and have seen the same wear, the surviving one often breaks soon after. Consider ordering two and replacing both while the dishwasher is already pulled out. Also inspect the door hinge cable at the same time; if it's frayed, kinked, or bent, replace it too. Key Features Genuine OEM part manufactured by GE to factory specifications — guaranteed fit and performance Hinge arm link — connects the door spring to the door hinge arm, allowing the spring to counterbalance the door's weight Enables the dishwasher door to open in a smooth, controlled motion rather than dropping open Supports the door's weight even when the lower rack is fully loaded and resting on the open door Prevents strain on the door hinges and door misalignment Small white plastic link, approximately 1-1/2" long, ~0.01 lbs Sold individually — note there is one link on each side of the door Replaces AP2039321, 270839, AH259336, EA259336, and PS259336 Fits over 2,100 dishwasher models across GE, GE Profile, Café, Monogram, Hotpoint, RCA, Haier, and Kenmore GE-built lines Inexpensive fix for a problem that would otherwise cost a service call — many customers report the entire repair takes about 15 minutes DIY repair — installs in 15–30 minutes with basic hand tools Product Specifications Part Number WD14X10009 Part Type Dishwasher Hinge Arm Link (Door Spring Link) Condition Genuine OEM Application Dishwashers (GE platform) Length Approximately 1-1/2" Weight Approximately 0.01 lbs Color White Material Plastic Function Connects the door spring to the door hinge arm Location Bottom of the dishwasher door hinge, both left and right sides Quantity Sold individually (dishwasher uses TWO — one per side) Model Coverage Over 2,100 models Compatible Brands GE, GE Profile, Café, Monogram, Hotpoint, RCA, Haier, Kenmore Installation Notes ⚠️ Unplug Dishwasher and Shut Off Water Before Starting — Wear Work Gloves Disconnect power at the breaker and shut off the water supply before beginning. Wear work gloves to protect your hands. Remove the screws holding the bottom kick plate (a nut driver works well here) and the anchor screws at the top of the dishwasher that secure it to the countertop. Carefully pull the dishwasher out 8–10 inches from the cabinet to expose the door springs and hinge arm links at the bottom on both sides. (Depending on how the dishwasher is plumbed, you may be able to do this without disconnecting the water supply, drain line, or electrical — pull only as far as the connections allow, and disconnect them only if necessary for access.) Look at the hinge assembly at the bottom of the door: you'll see a steel cable with a hooked end, a spring, and the small white plastic link that ties them together. If the link is broken, it may already be lying on the floor. Remove the old link by disconnecting it from the hinge and spring — if it's cracked but still in place, you can break the remaining pieces free. Install the new WD14X10009: place the hinge arm link into the spring, hook the spring onto the clip, and seat the link into the clip on the hinge arm. Note: on some models the crimped hook opening on the steel cable is tight — if the new link won't slide in easily, a small file can carefully open the hook opening enough to accept it. Check the other side of the door while you're in there — there's a second spring and link, and if it's aged or cracked, replace it now. Push the dishwasher back into place, reinstall the anchor screws and kick plate, restore power and water, and test the door: it should now lower smoothly under spring tension rather than falling open. Tools needed: Nut driver, Phillips screwdriver, small file (occasionally), work gloves. Frequently Asked Questions My dishwasher door falls open instead of lowering gently — is this the part? Almost certainly, yes. The door spring is what counterbalances the door's weight so it lowers in a controlled motion. The hinge arm link is the small plastic piece that connects that spring to the door hinge arm. When the link cracks or snaps, the spring is effectively disconnected — so the door has no counterbalance and drops open under its own weight. This is the classic symptom. To confirm, pull the dishwasher out a few inches and look at the bottom hinge area on each side: if a link is broken, you'll often find the pieces on the floor or the spring hanging loose. If both links are intact, check the door hinge cable for fraying or the spring for damage. Should I order one or two? Order two. Your dishwasher has a door spring and hinge arm link on both sides of the door — and this part is sold individually. Many customers order one, replace the broken link, push the dishwasher back into the cabinet, and only then realize the second link exists (and is the same age, with the same wear). Since the tedious part of the job is pulling the dishwasher out from under the counter, replacing both links while you're already in there is the smart move. At a few dollars each, having a spare on hand is cheap insurance against doing the whole job over in a few months. Why do these little plastic links break? Ordinary wear and tear. The hinge arm link is a small plastic component that carries a surprising amount of load — every time you open the door, it transmits the spring's counterbalancing force to the hinge arm, and that load increases dramatically when the lower rack is fully loaded and resting on the open door. Over thousands of open/close cycles across years of use, the plastic fatigues and eventually cracks or snaps. It's a consumable wear item on GE dishwashers, which is exactly why GE uses the same inexpensive part across 2,100+ models. Do I have to disconnect the water and electrical to pull the dishwasher out? Often not. Many customers find that removing the top anchor screws and the bottom kick plate, then sliding the dishwasher out 8–10 inches, gives enough access to reach the hinge arm links — without disconnecting the water supply, drain hose, or electrical. It depends on how much slack your installer left in those lines. Pull the dishwasher out only as far as the connections allow, and see whether you can reach the hinge area. If the lines are too short and you can't reach, you'll need to disconnect the water supply, drain tube, and electrical (turn off power and water first). Either way, the link replacement itself takes only a few minutes once you can reach it. Should I replace the door hinge cable at the same time? Inspect it, and replace it if it shows any damage. The door hinge cable is the steel cable that connects the door spring assembly to the door hinge — it works alongside the link and spring in the same counterbalance system. If the cable is frayed, kinked, bent, or its crimped hook end is damaged, it will fail soon and you'll be pulling the dishwasher out again. Since you already have access, this is the ideal moment to check it. Also inspect the door spring itself for stretching or breakage. Contact our support team with your model number if you need the correct cable or spring part number. Is this a Genuine OEM or aftermarket part? This is a Genuine OEM part manufactured by GE to factory specifications. It is the exact same hinge arm link installed in compatible GE, GE Profile, Café, Monogram, Hotpoint, RCA, Haier, and Kenmore GE-built dishwashers from the factory — guaranteed fit, materials, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less