Dryer Fuses, Thermostats, Heaters & Igniters

XPARTCO 35001092 Dryer Thermostat – Replaces WP35001092 – Compatible with Whirlpool, Maytag & Kenmore Dryers Product Description Maintain proper dryer temperature and consistent drying results with the XPARTCO 35001092 Dryer Thermostat. This High Limit Thermostat is a replacement part for specific dryer models. It plays a role in the safety and efficiency of the dryer's operation by monitoring and regulating the temperature within the dryer. This thermostat acts as a safety device, cutting off the heat source if the internal temperature exceeds safe levels, preventing potential overheating and fire hazards. Replaces Part Numbers WP35001092, 35001092, 1122485, PD00004704, EAP11741822, AP6008682, PS11741822.  Compatibility This replacement dryer thermostat fits select Whirlpool, Maytag, Kenmore, Amana, Crosley, and Estate electric dryers. Example compatible models include (but are not limited to):Whirlpool WED4815EW1, Maytag MEDC215EW1, Kenmore 110.65132411. Always verify your dryer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM temperature cycling performance 🌡️ Accurate Heat Regulation – Maintains safe, consistent drying temperatures 🔧 Reliable Thermal Control – Helps prevent overheating and heat loss 💰 Cost-Effective Repair – Quality alternative to OEM thermostats 🛡️ Fixes Common Issues – Solves no heat, overheating, long dry times, or blown fuses 📐 Product Specification Part Number: 35001092 Component Type: Dryer Operating Thermostat Application: Heater or exhaust temperature regulation Material: Heat-resistant metal thermostat housing Mounting: Screw-mounted Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver ⚠️ Safety First: Always unplug the dryer before servicing to avoid electrical shock. Steps: Disconnect dryer power and remove the rear access panel. Locate the thermostat on the heater housing or exhaust duct. Disconnect wiring and remove the old thermostat. Install the new XPARTCO 35001092 thermostat. Reconnect wiring, reinstall the panel, and restore power. Run a test cycle to confirm proper heating. ⏱️ Time Required: 10–15 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Restore proper dryer temperature control — Add to Cart Now for a dependable, budget-friendly repair!

Read more less

XPARTCO 279816 Dryer Thermostat Kit Product Overview The XPARTCO 279816 Dryer Thermostat Kit is designed to regulate temperature and protect your dryer from overheating. This dryer thermal cut-off kit is a replacement part for specific Maytag, Kenmore, Roper, Whirlpool dryer models. It is designed to prevent the dryer from overheating. Over time, these components can fail due to electrical issues, lint buildup blocking the exhaust vent, or normal wear and tear. A malfunctioning thermal cut-off kit can result in overheating, which can pose a safety hazard and affect the dryer’s performance. Quick Answer If your dryer is overheating, not heating properly, or shutting off unexpectedly, the 279816 thermostat kit may be faulty. Replacing it restores proper temperature control and safe operation. Replaces Part Numbers Replaces OEM part number: 279816, 279816VP, 3399848, 3977393, PD00002348, AWP39198, EAP334299, AH334299, EA334299, AP3094244, PS334299. Compatibility This dryer thermostat kit is compatible with select Whirlpool, Maytag, Kenmore, and other compatible dryers. Whirlpool Dryers: KEYS700LQ0, RED4640YQ1, GEN2000HZ1, LER4624DZ1, LER8857EZ2, KEYS850JT1, LEN1000HQ1, LER7646EQ0, LEQ9508PG1, WED5540ST0, GCEM2990TQ1, LER3624JQ1, 885461, LER4634EZ1, LER7646JT0, LER5624DQ1, GCEM2990TQ0, 3CEP2950DN0, GEW9878PG1, LER4634EQ1, LER5636EQ3, LER8858EQ2, LEB6000PQ1, REX5634KQ1, LEQ9508LG0, LEB6000KQ2, TEDS680DQ1, LEN1000PQ1, CEDX463RQ0, TEDS680BN2, LER3624BN2, 885464, GCE2900XSW4, REX5635EQ0, LEQ7030KQ1, WED5850SW0, LET6638DQ0, LEB6300PW1, REX6646AL2, LEV6634BQ2, CEP2960JQ0, REL4632BW3, LET7646EQ2, TEDS740PQ0, LEB6300LW1, YC EDS563SQ0, LER5848EQ3, LER5636EQ1, REX5635EN2, LER4634EQ1, LER5624DZ1, EED4300SQ0, YREX4634KQ2, LEN3624BN2, WED4750XQ1, LEQ8858JQ1, LEV6634DQ0, REL3612BW3, 4GWED4900YW1, GEQ8858HQ0, WED4815EW0, LER7646EZ0, MED5700TQ1, REL4636BL2, WED5550SQ0, LEV7646AN2, TEDX540RQ1, CEE2990AG2, KEYS750LQ2, REX3514RQ0, LEC6848AW3, CED147HXW0, REX5635EQ1, KEYS700GQ0, LEN3634DW0, REL4634BW3, KEYS710LQ1, RED4440VQ1, MEDC100YQ0, REL4632DL1, MED5640TQ0, LEN3634DW1, LER8648PQ0, KEYS700EZ0, YEED4300TQ0, MED5620TQ1, YWED4916FW0, IED4400VQ0, LER5634LW0, 4KWED5790VW1, YLEQ9857LW0, KEYS700GQ0, NED4655EW1, MED5840TW0, RES7648EQ0, YMEDX500BW1, 4GAED4900YW1, LEE9848BQ2, LEN2000LG0, 7EWED1730YW1, MEDC500VW1, WED5821SW0, LER5636PQ1, 3HLER5437JQ3, LER5634EQ0, LEV7646AW2, RED4440VQ0, CEDS563MQ1, REX6646AW2, RES7646KQ0, REX5635EN0, YLEQ5000KQ0, KEYS750LT1, WED5100SQ0, LET6638DQ0, TEDX640PQ1, KEYS750LT1, KEYS700EZ0, WED5000VQ1, KEYS850LE2, LEB6300LW1, KEYS850JT1, GEW9878PG0, MEDC300BW0, MEDC400BW0, MEDC500VW0 Maytag Dryers: YNED4500VQ0, MED6600TQ0, YMEDX500BW0, MED5700TQ1, MEDC215EW1, YMED5900TW0, MEDC100YQ0, MEDC555DW1, MEDC300BW0, MEDC400BW0, MEDC500VW0, MED5600TQ1, MED5620TQ1, MED5630TQ0, MED5640TQ0, MED5707TQ0, MED5720TQ0, MED5720TQ1, MED5740TQ0, MED5740TQ1, MED5800TW0, MED5820TW0, MED5820TW1, MED5821TW0, MED5840TW0, MED5840TW1, MED5870TW0, MED5870TW1, MED5900TW0, MED5900TW1, MED5920TW0, MED5921TW0, MEDX500BW0, MEDX500BW1, MEDX655DW1, YMEDC300XW0, YMEDC400BW0, YMEDC400BW1, YMEDC415EW0, YMEDC415EW1, YMEDX500BW0, YMEDX500BW1, YMED5740TQ0, YMED5740TQ1 Kenmore Dryers: 110.62872102, 110.66514691, 110.60212990, 110.68442700, 110.62342511, 110.60814990, 110.86405850, 110.96529120, 110.6012510, 110.66854690, 110.66822694, 110.C60122511, 110.96587410, 110.66722691, 110.66512692, 110.62882101, 110.62102311, 110.69422801, 110.66862501, 110.67132411, 110.61804000, 110.66862500, 110.62842100, 110.64832400, 110.62854101, 110.60202990, 110.62602101, 110.96572830, 110.86405150, 110.67442600, 110.6012511, 110.66864500, 110.69432800, 110.60012000, 110.96587210, 110.C61112010, 110.62886101, 110.64842400, 110.66101691, 110.68402700, 110.64102301, 110.96582120, 110.65132411, 110.96575100, 110.64602300, 110.67632600, 110.66652500, 110.64912200, 110.96563820, 110.96585410, 110.66642500, 110.60012001, 110.66712692, 110.67832790, 110.62724100, 110.88762791, 110.62602100, 110.66524501, 110.68622700, 110.96575200, 110.60012001, 110.66822690, 110.68202794, 110.67342700, 110.C62332511, 110.64602301, 110.62822101, 110.62712101, 110.62802102, 110.62802100, 110.66102500, 110.67834790, 110.60722990, 110.66808690, 110.67834791, 110.69812990, 110.67622600, 110.60232001, 110.68532700, 110.66801694, 110.61402310, 110.62512100, 110.66752501, 110.96580010, 110.96564420, 110.62824101, 110.96585200, 110.66702692, 110.63102100, 110.67422600, 110.61812000, 110.64924200, 110.69622800, 110.62622100, 110.66132411, 110.62514101, 110.61262310, 110.96586400, 110.6072010, 110.66854694, 110.68652700, 110.96566400, 110.67732791, 110.66854691, 110.96566400, 110.6072010 Always verify your dryer’s model number before ordering. Contact our support team if you’re unsure. Common Problems This Part Fixes Dryer overheating Dryer not heating Dryer shutting off prematurely Inconsistent drying temperatures Key Features Includes essential thermostats for temperature control Prevents overheating and improves safety Restores consistent drying performance High-quality aftermarket replacement kit Product Specifications Part Number: XP279816 Part Type: Dryer Thermostat Kit Brand: XPARTCO Condition: New OEM / Aftermarket: Aftermarket Application: Dryer Heating & Safety System Troubleshooting Guide Dryer too hot → Faulty thermostat No heat → Failed thermal cutoff Dryer stops mid-cycle → Overheat protection triggered When Should You Replace This Kit? Replace this kit if your dryer overheats, fails to heat properly, or shuts down unexpectedly due to temperature control issues. Installation Notes ⚠️ Disconnect power before installation. Access the thermostat assembly from the rear panel and install components securely according to your dryer model. Related Parts Dryer Heating Element Thermal Fuse Dryer Timer Frequently Asked Questions Will this kit fit my dryer?This kit fits many Whirlpool and compatible models. Always verify your model number. What does a thermostat kit do?It regulates dryer temperature and protects against overheating. What are signs of a bad thermostat?Overheating, no heat, or dryer shutting off unexpectedly. Is this OEM or aftermarket?This is a high-quality aftermarket replacement kit. Shop With Confidence Parts-O-Matic is a U.S.-based appliance parts retailer specializing in OEM and high-quality replacement parts. We offer fast shipping, reliable products, and expert support. Fast Shipping Quality Tested Parts Compatibility Support  

Read more less

5300622032 Genuine OEM Dryer Heater Restring - Compatible with Frigidaire, Electrolux, Kenmore Product Description Restore optimal drying performance with the 5300622032 Genuine OEM Dryer Heater Restring. This authentic Frigidaire-manufactured heating element restring coil is designed for select Frigidaire, Electrolux, Gibson, Kelvinator, Tappan, White Westinghouse, and Kenmore dryers, generating heat to efficiently dry clothes. Built for durability and precise fit, it addresses issues like no heat or insufficient heat. Note: Includes one heating element restring coil with 1/4" terminals (4600 watts, 240 volts). Does not include heater housing insulators (131472100) or terminal block (3202786). Disconnect power before installation. Verify compatibility with your dryer model. Replaces part numbers: 5300622032, 08015672, 3202787, 3281114, AH451031, DE335, EA451031, NQ00622032, Q000622032, Q622032, TJ90DE335, WQ622032, PD00000126, EAP451031, AP2135127, PS451031. Compatibility: Compatible with models including but not limited to: Frigidaire: FDE646GES0, FDE747GES0, FDE847GES0, F31C336ES0, F31C436ES0 Gibson: GSE746RFS0, GSE746RFS1, GDE336RES1, GDE546RES0 Tappan: TDE336RED0, TDE546REW0 Kenmore, Electrolux, Kelvinator, White Westinghouse: (select models, verify compatibility) Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Frigidaire, Electrolux, Gibson, Kelvinator, Tappan, White Westinghouse, and Kenmore dryers. 🔧 Specifications: Genuine OEM heating element restring coil, 1/4" terminals, 4600 watts, 240 volts. 💪 Reliable Performance: Authentic Frigidaire part ensures efficient heat generation and long-lasting operation. 🛠️ Easy Installation: Requires screwdriver, pliers, and nut driver; typically installed in 30–45 minutes. 🛡️ Effective Fixes: Resolves no heat or insufficient heat in the dryer. Product Specification Part Number: 5300622032 Component Type: Dryer heating element restring coil Material: Metal alloy coil Electrical Rating: 4600 watts, 240 volts Mounting: Fits within existing heater housing, screw-mounted Operating Conditions: Suitable for household dryer environments Compliance: UL listed, Prop 65 warning for California Installation Notes: Safety First: Disconnect the dryer from the power source before installation. Shop for high-quality appliance parts with a 30-day return policy. Keep your dryer heating efficiently today! Add to cart now for a reliable fix!

Read more less

XPARTCO 6931EL3001F Dryer Hi-Limit Thermostat The XPARTCO 6931EL3001F is an aftermarket replacement dryer rear hi-limit heater thermostat compatible with select LG and Kenmore electric and gas dryers. The hi-limit thermostat is a safety switch mounted on the heater housing that monitors the temperature at the heating element. If the heater temperature exceeds the safe operating limit, the thermostat opens its contacts to cut power to the heating element, protecting the dryer and its contents from overheating. When cooled, the thermostat resets automatically — but if it fails internally, it may remain open permanently, causing the dryer to produce no heat despite the thermal fuse and other components being intact. Rated L125-31C, 250V, 25A, this 3-terminal thermostat measures 2"L x 1-3/4"W x 1-1/4"H with approximately 1-5/8" between mounting holes (center to center). It is constructed from metal and plastic in gray/black and mounts directly on the heater housing. It directly replaces 1377779, AP5072172, AH3530482, EA3530482, EAP3530482, PS3530482, and PD00023316. Often replaced together with the 6931EL3003D thermal fuse — both mount on the heater housing and work as a system to protect the dryer from overheating. Installs in 15–20 minutes with basic hand tools. Quick Answer The XPARTCO 6931EL3001F Dryer Hi-Limit Thermostat fixes LG and Kenmore dryers with no heat where the thermostat has failed open. Rated L125-31C, 250V/25A, 3 terminals. 2"L x 1-3/4"W x 1-1/4"H, ~1-5/8" between mounting holes. Mounts on heater housing. Test with multimeter — should show closed continuity at room temperature. Often replaced together with 6931EL3003D thermal fuse. Replaces 1377779, AP5072172, AH3530482, EA3530482, EAP3530482, PS3530482. Common Problems This Part Fixes Dryer produces no heat — hi-limit thermostat has failed open and is permanently interrupting the heater circuit Dryer takes much longer than normal to dry a load Dryer tumbles normally but generates no heat during the cycle No heat even after the thermal fuse has already been replaced — thermostat also failed Dryer overheating intermittently — thermostat not opening at the correct temperature Multimeter test shows open circuit (no continuity) across the thermostat at room temperature Replaces Part Numbers This hi-limit thermostat directly replaces the following OEM and cross-reference part numbers: 6931EL3001F, 1377779, AH3530482, ALG51960, EA3530482, EAP3530482, AP5072172, PD00023316, PS3530482 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This hi-limit thermostat is compatible with select LG and Kenmore electric and gas dryers. Compatible models include LG DLE, DLG, DLEX, DLGX, and DLB series dryers, and Kenmore 796-series dryers built on the LG platform. LG electric dryers — DLE series (DLE2050W, DLE3777W, DLE5955W and related models) LG electric dryers — DLEX series (select models) LG gas dryers — DLG series (DLG2051W, DLG3788W and related models) LG gas dryers — DLGX series (select models) LG electric and gas dryers — DLB series (select models) Kenmore / Sears dryers — 796-series (LG-built models) Tip: When replacing the 6931EL3001F thermostat, also replace the 6931EL3003D thermal fuse at the same time. Both mount on the heater housing and are commonly replaced together — an overheating event that causes one to fail typically stresses both. Key Features Hi-limit heater thermostat — safety switch that cuts power to the heating element if heater temperature exceeds safe limits Auto-resets when cooled — but a failed thermostat that remains open causes permanent no-heat Rated L125-31C, 250V, 25A — correct specifications for compatible LG and Kenmore dryers 3-terminal design — matches the original wiring configuration on compatible heater housings Dimensions: 2"L x 1-3/4"W x 1-1/4"H; ~1-5/8" between mounting holes (center to center) Metal and plastic construction (gray/black) — heat-resistant materials for heater housing application Mounts directly on the heater housing — accessible from the dryer back panel Often replaced together with 6931EL3003D thermal fuse for a complete heater housing thermal repair Test with multimeter before replacing — should show closed continuity at room temperature Aftermarket replacement built to OEM-equivalent quality standards Quick DIY repair — installs in 15–20 minutes with basic hand tools Product Specifications Part Number 6931EL3001F Part Type Dryer Rear Hi-Limit Heater Thermostat Condition Aftermarket Replacement Application LG and Kenmore Electric and Gas Dryers Thermostat Rating L125-31C — auto-resets after cooling Voltage 250V Amperage 25A Terminals 3-terminal Dimensions 2"L x 1-3/4"W x 1-1/4"H Mounting Hole Spacing Approx. 1-5/8" center to center Color Gray / Black Material Metal / Plastic Location Heater housing (rear of dryer) Normal Behavior Closed continuity at room temperature Often Replaced With 6931EL3003D Thermal Fuse Compatible Brands LG, Kenmore (LG-built) Installation Notes ⚠️ Unplug Dryer and Shut Off Gas Before Starting Disconnect power (and shut off gas for gas dryers) before beginning. Remove the back panel of the dryer by unscrewing the perimeter screws to access the heater housing. The 6931EL3001F thermostat is mounted on the heater housing — it is the 3-terminal component with gray/black housing. Before removing it, test it with a multimeter: disconnect the wires and probe the terminals. At room temperature a working thermostat shows closed continuity. An open reading confirms failure. Photograph the 3-wire connections before disconnecting — reconnecting in the correct positions is important. Remove the 2 mounting screws and lift the old thermostat off. Install the new thermostat in the same position with the 2 mounting screws and reconnect the wires in the same positions. While the heater housing is accessible, also test and replace the 6931EL3003D thermal fuse if needed. Reinstall the back panel, restore power, and run a test heat cycle. Tools needed: Phillips screwdriver, multimeter. Frequently Asked Questions What is the difference between the 6931EL3001F thermostat and the 6931EL3003D thermal fuse? Both are mounted on the heater housing and protect the dryer from overheating, but they work differently. The 6931EL3001F is a resettable hi-limit thermostat rated L125-31C — it opens when the heater temperature gets too high and resets automatically when cooled. The 6931EL3003D is a one-time thermal fuse that permanently interrupts the circuit if the temperature exceeds its rated limit — once blown, it cannot reset and must be replaced. Both should show closed continuity at room temperature when working. Because both are on the heater housing and experience the same thermal stress, replacing both at the same time is recommended. How do I test the 6931EL3001F thermostat with a multimeter? Unplug the dryer and disconnect all three wires from the thermostat terminals. Set your multimeter to continuity or resistance mode. At room temperature, a working 6931EL3001F thermostat should show closed continuity (near-zero resistance) across its contacts. If your multimeter reads open circuit (no continuity / OL), the thermostat has failed and needs replacement. Since this thermostat auto-resets when cooled, always test at room temperature — testing while the dryer is still warm may give a false open reading if the thermostat has legitimately opened due to heat. My LG dryer has no heat but the thermal fuse is good — could it be the thermostat? Yes — when the thermal fuse tests good but there is still no heat, the hi-limit thermostat (6931EL3001F) is the next most common culprit. A thermostat that has failed internally may remain permanently open even at room temperature, cutting power to the heating element exactly as a blown thermal fuse would. Test the thermostat with a multimeter for continuity. Also check the cycling thermostat (6931EL3002M) and the thermistor (6323EL2001B) — all three are part of the LG dryer thermal control system and any one of them can cause a no-heat condition. What does the "L125-31C" rating mean? The L125-31C rating describes the thermostat's operating parameters. L125 means the thermostat opens (trips) when the temperature reaches approximately 125°C (257°F). The 31 indicates the reset differential — the thermostat resets when the temperature drops approximately 31°C below the trip point, around 94°C (201°F). This rating ensures the thermostat allows the heater to operate at normal drying temperatures while protecting against dangerous overheating. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine LG OEM part, but is manufactured from metal and plastic to match the L125-31C rating, dimensions, and 3-terminal configuration of the original 6931EL3001F hi-limit heater thermostat. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

8557403CM Dryer Thermostat  Replaces Part Numbers: WP8557403, 8557403, 1180102, AP6013164, PS11746386. Description: This Dryer Thermostat is a replacement part for select Kenmore, Maytag, Whirlpool dryer models. It regulates the temperature inside the dryer, ensuring that it maintains the correct heat levels for safe and efficient drying cycles.   This is an aftermarket part that can be used as a replacement for the OEM part.

Read more less

XPARTCO W10900067 Dryer Thermal Cut-Off Fuse & Thermostat Kit – Compatible with Whirlpool, Maytag & Kenmore Dryers Product Description Restore safe and reliable dryer heating with the XPARTCO W10900067 Dryer Thermal Cut-Off Fuse & Thermostat Kit. This cut-off terminal is a replacement Part for specific Kenmore, Maytag, Roper, Whirlpool dryer models. The kit contains a 309°F Thermal Cut-Off Fuse and a high limit thermostat. In electric dryers, it shuts off the heat if overheating occurs to prevent fire risk. The thermal fuse cuts power while the thermostat regulates the operating temperature. To install, first, unplug the dryer. Use a multimeter to test the old fuse for continuity at room temperature; it should read zero ohms. XPARTCO is a trusted aftermarket brand offering appliance replacement parts built to OEM-equivalent specifications at a cost-effective price. Replaces Part Numbers W10900067, 4460718, N197, 197CM, 197, PD00046493, EAP11769432, AP6036100, PS11769432. Compatibility This replacement dryer thermal cut-off fuse and thermostat kit fits select Whirlpool, Maytag, Kenmore, Amana, Estate, Roper, and Crosley electric dryers. Example compatible models include (but are not limited to): Whirlpool WED4800XQ, WED4815EW1 Maytag MEDC215EW1 Kenmore 110.6012010 Always verify your dryer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement Kit – Matches OEM temperature and safety specifications 🌡️ Accurate Heat Protection – Helps regulate dryer temperature safely 🔥 Overheat Safety Cut-Off – Prevents damage caused by excessive heat 💰 Cost-Effective Repair – Reliable alternative to higher-priced OEM kits 🛡️ Fixes Common Issues – Resolves no heat, overheating, and thermal shutdowns 📐 Product Specification Part Number: W10900067 Component Type: Dryer Thermal Cut-Off Fuse & Thermostat Kit Includes: Thermal cut-off fuse and high-limit thermostat Application: Heater housing / exhaust temperature control Material: Heat-resistant metal housings Mounting: Screw-mounted Quality Level: Aftermarket replacement (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver ⚠️ Safety First: Always unplug the dryer before servicing to avoid electrical shock. Basic Steps: Disconnect dryer power. Remove the rear access panel. Locate the thermal cut-off and thermostat on the heater housing. Disconnect wiring and remove old components. Install the new XPARTCO W10900067 components in the same positions. Reconnect wiring, reinstall panel, and restore power. Run a test cycle to confirm proper heating. ⏱️ Time Required: 20–30 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Aftermarket Appliance Parts 🔄 30-Day Return Policy Restore safe dryer heating and protection — Add to Cart Now for a dependable, budget-friendly repair!

Read more less

XPARTCO WE1M1002 Dryer Fuse, 30 AMP 120V – Compatible with GE, Hotpoint & Kenmore Dryers Product Description Restore proper electrical protection and safe dryer operation with the XPARTCO WE1M1002 Dryer Fuse, 30 AMP 120V. This Dryer line fuse is a replacement part for specific GE clothes dryer models. The XPARTCO WE1M1002 Dryer Fuse provides 30 AMP, 120V protection against power surges and short circuits. Safeguard your dryer from potential damage and ensure optimal performance. Designed for easy installation and lasting reliability. XPARTCO is a trusted aftermarket brand offering appliance replacement parts built to OEM-equivalent specifications at a cost-effective price. Replaces Part Numbers WE1M1002, 1974262, PD00029481, EAP3496852, AGE25598, AH3496852, EA3496852, AP5270172, PS3496852. Compatibility This replacement dryer fuse fits select GE, Hotpoint, and Kenmore (GE-manufactured) electric dryers. Example compatible models include (but are not limited to): GE GTDP220EF3WW, GTDP300EM1WS Hotpoint HTDX100EM1WW Kenmore 363.9158210 Always verify your dryer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM electrical and amperage specifications ⚡ 30 AMP, 120V Rating – Designed for proper circuit protection 🛡️ Critical Safety Component – Helps prevent electrical damage and hazards 💪 Durable Construction – Built for reliable, long-term performance 💰 Cost-Effective Repair – Affordable alternative to OEM dryer fuses 📐 Product Specification Part Number: WE1M1002 Component Type: Dryer Electrical Fuse Amperage Rating: 30 AMP Voltage Rating: 120V AC Application: Dryer power and control circuit protection Mounting: Inline or holder-mounted (model dependent) Quality Level: Aftermarket replacement (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, needle-nose pliers ⚠️ Safety First: Always unplug the dryer before servicing to prevent electrical shock. Basic Steps: Disconnect dryer power. Access the fuse holder or control area. Remove the blown fuse. Install the new XPARTCO WE1M1002 fuse. Reassemble panels and restore power. Test dryer operation. ⏱️ Time Required: 10–15 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Aftermarket Appliance Parts 🔄 30-Day Return Policy Restore dryer power and electrical protection — Add to Cart Now for a dependable, budget-friendly repair!

Read more less

EXPWE4X693 Dryer Gas Valve Solenoid 2 Terminal Description: The M Series Coil is a replacement part for specific GE, Hotpoint dryer models. It is a main valve coil, approximately 1 inch long and wide, with two terminals. It has a white and black color pattern. Its key function is to open the gas valves during the operation of the dryer. Utilized in conjunction with two coil gas shut-off valve assemblies. It ensures a consistent release of gas to maintain the flame during the drying process. Replaces Part Numbers: WE4X693, WE04X0693, AH268154, EA268154, AP2042753, PS268154. This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: California’s Proposition 65 

Read more less

XPARTCO 5300622034 Dryer Heater Restring Terminal Size: 5/16 inch 4600 Watts 240 Volts. Restring Coil for 131553900, WE14X10015 Replaces Part Numbers: 5300622034, AH451032, EA451032, OEM6405389, AP2135128, PS451032. Description:  This Electric Dryer Heating Element is a replacement part for specific Frigidaire dryer models. Located within the dryer drum cavity, this component produces the necessary hot air to evaporate moisture from wet laundry. Terminal Size: 5/16 inch.  This electric dryer heating element restring coil does not include the heater housing insulators.   This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

ERP W10909685 Dryer Thermal Fuse Dryer thermal fuse located on the blower housing. If the dryer overheats, the thermal fuse blows cutting off power to the motor or the heating system. When the fuse is bad the dryer won't start or will run but not heat. The thermal fuse cannot be reset. Fuses often blow due to a clogged dryer vent. Replaces part Numbers: W10909685, W10693363, G4AP0506, F 091C ACA2, PD00036363, EAP11766766, AP6034383, PS11766766.   This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

134120900 Genuine OEM Dryer Thermal Fuse - Compatible with Frigidaire, Electrolux, Kenmore Product Description Ensure your dryer operates safely with the 134120900 Genuine OEM Dryer Thermal Fuse. This Frigidaire-manufactured thermal limiter, with a 220°F limit, is designed to prevent overheating in select Frigidaire, Electrolux, Kenmore, and other compatible dryers by cutting off power if the dryer exceeds safe temperatures. It addresses issues like the dryer not starting, shutting off too soon, or overheating, ensuring safe and reliable performance. This non-resettable fuse must be replaced if blown. Note: Includes (1) thermal fuse. Disconnect power before installation. Verify compatibility with your dryer model. Replaces part numbers: 134120900, 146062-0, 146062-00, 146062-000, 1489053, 3205659, 5303209192, AH419402, EA419402, PD00000113, EAP419402, AP2108182, PS419402. Compatibility: Compatible with select dryer and washer/dryer combo models, including but not limited to: Frigidaire: LEQ1442ES0, FDE436RES0, FDE546RES0, FDE558GES0 Electrolux: EKDR14XAKW0, FFLE1011MW2, FFLE2022MW2, FFLE3911QW0 Kenmore: 417.49012890, 417.49022890, 417.97561601 Crosley: BEQ1442CES0, CDE2000FW0, CDE4000FW0 White-Westinghouse: WDE336RES0 Common models: Frigidaire FDE216RES0, Electrolux FFLE4033QW0, Kenmore 417.97591220 Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Frigidaire, Electrolux, Kenmore, Crosley, White-Westinghouse, and other dryers. 🔧 Specifications: Genuine OEM Frigidaire thermal fuse, 220°F limit, non-resettable. 💪 Reliable Performance: Prevents overheating by cutting power, ensuring safe dryer operation. 🛠️ Easy Installation: Requires a screwdriver and pliers; typically installed in 15–20 minutes. 🛡️ Effective Fixes: Resolves dryer not starting, shutting off too soon, overheating, or no heat issues. Product Specification Part Number: 134120900 Component Type: Dryer thermal fuse (thermal limiter) Material: Metal and plastic Operating Conditions: 220°F limit, 125/250V Compliance: UL-listed, Prop 65 warning for California Installation Notes: Safety First: Disconnect the dryer from the power source before installation. Shop for high-quality appliance parts with a 30-day return policy. Keep your dryer running safely today! Add to cart now for a reliable fix!

Read more less

(8 Pack) 3977394 Dryer Thermal Cut-Off Kit – Replaces 3977394 – Compatible with Whirlpool, Kenmore, Maytag, and KitchenAid Dryers Product Description Protect your dryer from overheating with the 3977394 Dryer Thermal Cut-Off Kit. This high-quality aftermarket replacement shuts off the heating element if the dryer temperature rises above safe operating limits. A failed cut-off can cause no-heat issues or overheating during drying cycles. Installing this reliable 3977394 kit restores safe temperature control and helps prevent damage to internal components. Replaces Part Numbers XPTC352, 3977394, 352F Compatibility This replacement thermal cut-off kit fits select Whirlpool, Kenmore, Maytag, Roper, Estate, Crosley, and KitchenAid dryers. Example compatible models include (but are not limited to): Whirlpool WED4815EW1, Kenmore 110.86573110, and Maytag MEDC215EW1. Always verify your dryer’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM safety and temperature performance 🔥 Overheat Protection – Automatically shuts off power to the heating element if the dryer overheats 💰 Cost-Effective Fix – Affordable alternative to OEM thermal cut-off kits 🛠️ Easy Installation – Direct-fit design with included thermostats and connectors 🛡️ Fixes Common Issues – Solves dryer not heating, overheating, or shutting off prematurely 📐 Product Specification Part Number: 3977394 Component Type: Dryer Thermal Cut-Off Kit Includes: Thermal cut-off, high-limit thermostat, mounting hardware, and wire connectors Temperature Rating: Cut-off opens at ~352°F. Material: Metal thermostat housing and heat-resistant components Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Nut driver, Phillips screwdriver ⚠️ Safety First: Always unplug the dryer before performing any repairs to prevent electrical shock. Steps: Disconnect power and remove the rear dryer panel. Locate the heating element housing and identify the cut-off and thermostat. Disconnect wires and remove the old components. Install the new 3977394 cut-off and thermostat in the same locations. Reconnect wires, reassemble the back panel, and restore power. Run a short test cycle to verify proper heating. ⏱️ Time Required: 15–25 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Keep your dryer safe and efficient — Add to Cart Now for a reliable, budget-friendly repair!

Read more less