Washer Belts, Pulleys, Suspension & Transmission Parts

DC61-02432A Genuine OEM Samsung Washer Suspension Spring Guide The DC61-02432A is a genuine Samsung OEM suspension spring guide (bracket) for Samsung and select Kenmore washers. This small but structurally important bracket connects the washer's outer frame to one of the suspension springs that support the wash tub, keeping the spring correctly seated and aligned as the tub moves during fill, wash, and especially spin. The tub itself hangs suspended inside the cabinet, and it's this network of springs and guides that lets it move and absorb vibration without banging against the surrounding frame or panels. Because this guide holds the spring in its proper working position, a cracked, worn, or broken guide lets the spring drift out of alignment or lose tension where it seats. The result is usually excessive tub movement, unusual banging or knocking noises (especially during spin), or a washer that seems to "walk" or vibrate more than it used to. Left unaddressed, a spring that has come loose from a failed guide can allow the tub to strike the cabinet repeatedly, accelerating wear on nearby components. It directly replaces AP5581510, 2069491, and PS4206750. As a genuine OEM part, the DC61-02432A is manufactured by Samsung to factory specifications — guaranteed fit, materials, and performance. Quick Answer The DC61-02432A Genuine OEM Samsung Washer Suspension Spring Guide fixes Samsung and select Kenmore washers with excessive tub movement, unusual banging or knocking noise (especially during spin), a washer that vibrates or "walks" more than it used to, or a suspension spring that has come loose or shifted out of position. Connects the washer frame to the suspension spring. Replaces AP5581510, 2069491, PS4206750. This bracket doesn't replace or include the spring itself — if the spring is stretched, rusted, or broken, it should be replaced separately alongside this guide. Common Problems This Part Fixes Excessive tub movement or vibration, especially noticeable during spin Unusual banging, knocking, or thudding noise from inside the cabinet Washer that vibrates more than it used to, or seems to "walk" across the floor during spin Suspension spring that has come loose, shifted, or disconnected from its mounting point Tub striking the cabinet frame or nearby panels during operation Visible cracking or breakage on the guide/bracket where the spring attaches Noise that has gradually worsened over time as the guide wears Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer suspension spring guide directly replaces the following OEM and cross-reference part numbers: DC61-02432A, AP5581510, 2069491, ASM33826, PD00026723, PS4206750 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This suspension spring guide is compatible with select Samsung washers, and also fits select Kenmore washers built on the Samsung platform, including model numbers such as: Samsung 402-49032012 Samsung 592-49006, 592-49032, 592-49042, 592-49045, 592-49052, 592-49075 Kenmore 40249032012 Note: This is the spring guide/bracket only — it does not include the suspension spring itself. If your spring is stretched, rusted, corroded, or broken, order the correct spring separately in addition to this guide. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine Samsung OEM part — factory-specified bracket geometry and mounting fit Connects the washer's outer frame to the suspension spring, keeping it correctly seated and aligned Resolves "excessive tub movement," "banging or knocking noise," "washer vibrating or walking," and "loose spring" symptoms caused by guide failure Direct drop-in replacement — mounts to the original frame attachment point Simple, tool-light installation Replaces AP5581510, 2069491, and PS4206750 Compatible with a range of Samsung and select Kenmore washers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number DC61-02432A Part Type Washer Suspension Spring Guide / Bracket Condition Genuine OEM Brand Samsung Function Connects and aligns the washer frame to the suspension spring Includes Spring No — bracket/guide only, spring sold separately Quantity 1 spring guide Compatible Brands Samsung, Kenmore Installation Notes ⚠️ Unplug Washer Before Starting Disconnect power at the outlet before beginning. Wear work gloves. Depending on your washer's design, you may need to remove the cabinet or rear access panel to reach the suspension spring and its guide bracket at the top of the tub assembly. Photograph how the old guide and spring are connected to the frame before removing anything, since suspension components are often symmetrical and easy to reverse or mismatch between mounting points. Carefully release the tension on the affected spring — depending on the model, this may involve unhooking the spring from the frame or the tub side first, then removing the old guide from its mounting point on the frame. Install the new DC61-02432A guide in the same position, then reattach the spring, making sure it seats fully and squarely in the new guide. Check any other springs and guides in the suspension system while you're in there, since if one has failed from age or wear, the others are often not far behind. Reassemble any panels you removed, restore power, and run a spin cycle to confirm the excessive movement, vibration, or banging noise has resolved. Tools needed: screwdriver (model-dependent access), pliers (helpful for spring tension), work gloves. Frequently Asked Questions My washer bangs loudly during spin. Is this the part I need? It's a strong possibility, especially if the banging has developed gradually or seems to come from inside the cabinet near the tub. This guide keeps the suspension spring seated and aligned; when it cracks or wears out, the spring can shift out of position, letting the tub move more than it should and strike nearby components. Before ordering, it's worth opening up the access panel if you're comfortable doing so, to visually confirm whether a spring has come loose or a guide bracket looks cracked or broken. Does this part include the suspension spring? No — this is the guide/bracket only, which connects the frame to the spring. If your suspension spring itself is stretched, rusted, corroded, or snapped, you'll need to order the correct spring for your model separately in addition to this guide. Should I replace just one guide, or check the others too? It's worth inspecting the other suspension springs and guides while you have access, since they're typically all the same age and subject to the same wear. If one has failed, the others may not be far behind, and replacing them together can save you from repeating this repair again soon after. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Samsung to factory specifications — guaranteed fit, materials, and performance. It matches the original bracket geometry and mounting fit of the suspension spring guide originally installed in your washer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO W10734521 Washer Clutch Slider Kit The XPARTCO W10734521 is an aftermarket replacement washer clutch slider kit compatible with a wide range of Whirlpool, Maytag, Kenmore, KitchenAid, Amana, Crosley, Estate, Jenn-Air, Roper, Magic Chef, Admiral, and Kirkland HE top-load washers. The clutch slider kit is part of the drive system that engages and disengages the inner tub from the gearcase — it's responsible for transitioning the washer between agitation and spin modes. The slider gear works together with the electromagnetic clutch and gearcase to move the inner tub during the wash and spin portions of every cycle. When the slider or its spring fails, the washer typically won't spin properly, won't agitate, makes grinding noise, or leaves clothes soaking wet at the end of a cycle. This kit includes the slider, spring support, 30mm spiral, and bolt. Slider dimensions: 2-7/8" outer diameter x 7/8" deep. Support spring: 1-5/8" outer diameter x 1-1/8" long. Spiral: 1-5/16" outer diameter. Bolt: 7/8" head diameter x 1" high. Construction is metal and plastic in black, white, and gray. Important: this is the slider kit only — it does NOT include the electromagnetic clutch (sold separately as W10754448). The current W10734521 part number supersedes the earlier W10006484, W10006494, W10275082, W10447975, and W10905025. It also replaces 3452506, AP5952873, EAP10060062, PD00025495, and PS10060062. Installs in 60–90 minutes with basic hand tools. Quick Answer The XPARTCO W10734521 Washer Clutch Slider Kit fixes Whirlpool, Maytag, Kenmore, KitchenAid, and related HE top-load washers that won't spin or agitate properly, won't transition between cycle phases, leave clothes soaking wet, or make grinding noise during the spin cycle. Slider kit only — electromagnetic clutch (W10754448) is sold separately. Includes slider (2-7/8" OD), spring support (1-5/8" OD), 30mm spiral, and bolt. Replaces W10006484, W10006494, W10275082, W10447975, W10905025, 3452506, AP5952873, EAP10060062, PD00025495, PS10060062. Common Problems This Part Fixes Washer won't spin or spins very slowly — slider not engaging the gearcase for spin mode Washer won't agitate — slider not transitioning the drive system to agitation mode Clothes left soaking wet at the end of the cycle — incomplete spin Grinding, rattling, or clunking noise during the spin or agitation phase Washer fills and drains normally but never spins or agitates Worn or broken slider gear teeth visible on the drive assembly Weak or broken slider spring — washer drive losing positive engagement Repeated cycle interruptions in the spin or agitation portion of cycles What's in the Kit Part 1 Slider Gear 2-7/8" outer diameter x 7/8" deep · Slides over the drive assembly shaft to engage/disengage the gearcase for agitation and spin transitions · Install with the teeth facing outward Part 2 Spring Support 1-5/8" outer diameter x 1-1/8" long · Provides return tension for the slider · Replace whenever the gearcase or slider is replaced — spring can weaken over time Part 3 30mm Spiral 1-5/16" outer diameter · Spiral retaining component that holds the slider assembly together on the drive shaft Part 4 Bolt 7/8" head diameter x 1" high · Secures the assembly Replaces Part Numbers This clutch slider kit directly replaces the following OEM and cross-reference part numbers: W10734521, 3452506, W10006484, W10006494, W10275082, W10447975, AP5952873, AWP41487, EAP10060062, PD00025495, PS10060062. W10734521 is the current production part superseding W10006484, W10006494, W10275082, W10447975, and W10905025. Contact our support team with your model number if you need confirmation before ordering. Compatibility This clutch slider kit is compatible with select HE top-load washers from the following brands: Whirlpool top-load washers (Cabrio, WTW5000, WTW5500, WTW5700, WTW6000, WTW6200, WTW6400, WTW7000, WTW7120, WTW8000, WTW8200, WTW8500, WTW8700 series and related models) Maytag top-load washers (Bravos and Centennial series and related models) Kenmore / Sears top-load washers (Whirlpool-built — select 110-series and related models) KitchenAid top-load washers (select models) Amana top-load washers (select models) Crosley top-load washers (select models) Estate top-load washers (select models) Jenn-Air top-load washers (select models) Roper top-load washers (select models) Magic Chef top-load washers (select models) Admiral top-load washers (select models) Kirkland top-load washers (select models) Important — Slider Kit Only, NOT Clutch: This is the clutch slider kit (slider, spring, spiral, bolt) — it does not include the electromagnetic clutch assembly. The electromagnetic clutch is part number W10754448 and is sold separately. If you need both components, order each part separately. Many repair scenarios call for replacing both at the same time, since both wear together. Always verify your model number and confirm exactly which component has failed before ordering. Key Features Complete slider repair kit — slider, spring support, 30mm spiral, and bolt included as a matched set Works with the electromagnetic clutch and gearcase to drive the inner tub during agitation and spin modes Resolves "won't spin," "won't agitate," and "clothes left soaking wet" symptoms when the slider has worn or the spring has weakened Current production part number — supersedes W10006484, W10006494, W10275082, W10447975, and W10905025 Slider: 2-7/8" outer diameter x 7/8" deep · Spring: 1-5/8" OD x 1-1/8"L · Spiral: 1-5/16" OD · Bolt: 7/8" head x 1"H Metal and plastic construction in black, white, and gray Important: slider kit only — electromagnetic clutch (W10754448) sold separately For full performance, replace all components in the kit together as a set Compatible with Whirlpool, Maytag, Kenmore, KitchenAid, Amana, Crosley, Estate, Jenn-Air, Roper, Magic Chef, Admiral, and Kirkland HE top-load washers Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 60–90 minutes with basic hand tools Product Specifications Part Number W10734521 Supersedes W10006484, W10006494, W10275082, W10447975, W10905025 Part Type Washer Clutch Slider Kit Condition Aftermarket Replacement Application HE Top-Load Washers (Whirlpool platform) Includes 1x Slider, 1x Spring Support, 1x 30mm Spiral, 1x Bolt Slider Dimensions 2-7/8" Outer Diameter x 7/8" Deep Spring Support Dimensions 1-5/8" Outer Diameter x 1-1/8" Long Spiral Dimensions 1-5/16" Outer Diameter Bolt Dimensions 7/8" Head Diameter x 1" High Material Metal / Plastic Color Black / White / Gray Electromagnetic Clutch NOT included — see W10754448 (sold separately) Compatible Brands Whirlpool, Maytag, Kenmore, KitchenAid, Amana, Crosley, Estate, Jenn-Air, Roper, Magic Chef, Admiral, Kirkland Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting — Wear Work Gloves Disconnect power and turn off the water supply before beginning. Place towels under the washer — some residual water may spill from hoses during disassembly. Wear work gloves to protect your hands. Unthread the hot and cold water supply hoses from the inlet valve ports. Disconnect the drain hose from the outlet port using channel-lock pliers to release the spring clamp. Carefully tip the washer onto its side or back on a padded surface to access the underside. Disconnect the wiring harnesses to the drive motor and pull the rotor free — be prepared for some resistance, as the permanent magnets in the rotor require some effort to remove. Use a small awl inserted between the slider gear teeth to release the spring retainer. With the retainer released, pull off the old spring and slider gear. Note the orientation of the slider — teeth facing outward. Install the new W10734521 components in sequence: slide the new slider gear onto the drive assembly shaft with teeth facing outward, install the new spring support and 30mm spiral, and secure with the new bolt. Reinstall the rotor (the magnets will pull it into place), reconnect the wiring harnesses, return the washer to upright, reconnect supply hoses and drain hose, restore power and water, and test the spin cycle for proper function. Tools needed: Phillips screwdriver, socket set, channel-lock pliers, small awl, padded surface for tipping, work gloves. Frequently Asked Questions What's the difference between W10734521 and W10754448? These are two different parts in the same drive system. The W10734521 is the clutch slider kit — it includes the slider gear, spring support, spiral, and bolt that physically engage/disengage the inner tub from the gearcase to transition between agitation and spin modes. The W10754448 is the electromagnetic clutch itself — the electrical component that drives the engagement. Both can fail independently, and many repair scenarios call for replacing both at the same time since they work together. Confirm exactly which component has failed before ordering, or order both if you're rebuilding the drive system as a full repair. My washer won't spin — is it the slider or something else? A washer that won't spin can have several causes: a failed slider kit, a failed electromagnetic clutch (W10754448), a damaged drive belt, a failed motor or rotor, a broken lid switch, or — on some models — a failed gearcase. The slider kit is one of the more common causes when the symptom is "fills and drains but won't spin" with no obvious noise or burning smell. Before replacing the slider, check that the lid latch strike (W11457841 on some models) is engaging properly, the drive belt is intact, and the motor is functioning. If those check out and the slider gear shows visible wear, missing teeth, or a stretched spring, the W10734521 kit is the right repair. Should I replace all parts in the kit together? Yes — for the kit to perform as designed, all components should be replaced as a matched set. The slider, spring support, spiral, and bolt all work together — if one is worn, the others have typically experienced the same load and wear. Reusing old components alongside new ones can cause premature failure of the new parts and a repeat repair. The W10734521 kit is priced and packaged for a complete replacement, so install all four pieces during your repair. What is the difference between W10734521 and the older part numbers it replaces? W10734521 is the current production version of this slider kit. It directly supersedes W10006484, W10006494, W10275082, W10447975, and W10905025 — all of which were earlier OEM part numbers for variations of the same slider kit across production revisions. Whirlpool consolidated these into the W10734521 to streamline the parts catalog. If your washer's parts diagram shows any of these older numbers, the W10734521 is the correct current replacement. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured from metal and plastic to match the dimensions, gear profile, and drive engagement function of the original W10734521 clutch slider kit used in compatible Whirlpool, Maytag, Kenmore, and related HE top-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 5304516132 Washer Drive Belt – Compatible with Frigidaire, Electrolux, and Kenmore Washers Product Description Keep your washer spinning smoothly with the XPARTCO 5304516132 Washer Drive Belt. This high-quality aftermarket replacement transfers power from the motor to the washer drum, enabling proper agitation and spin speed. A worn, stretched, or broken belt can cause slow spinning, loud noises, or the drum not turning at all. Replacing it with this durable XPARTCO belt restores reliable performance and efficient wash cycles. Replaces Part Numbers 5304516132, 12638000001161, 7PJE607, PD00055739, EAP12585162, 4839724, AP6339955, PS12585162. Compatibility This replacement drive belt fits select Frigidaire, Electrolux, and Kenmore front-load washers. Example compatible models include (but are not limited to): Frigidaire FAFW3801LW, Electrolux EWFLS70JSS0, and Kenmore 417.41122310. Always verify your washer's model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Matches OEM fit and performance at a lower cost ⚙️ Restores Drum Motion – Ensures proper spinning, agitation, and wash performance 💪 Durable Construction – Made with reinforced rubber for long-lasting tension 🛠️ Easy Installation – Designed for quick DIY replacement 🛡️ Fixes Common Issues – Solves slow spinning, no spin, squealing noises, or drum not turning 📐 Product Specification Part Number: 5304516132 Component Type: Washer Drive Belt Material: Reinforced rubber with tension-resistant cord Dimensions: Exact OEM-equivalent sizing for proper tension Mounting: Wraps around motor pulley and drum pulley Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, nut driver (depending on model) ⚠️ Safety First: Always unplug the washer before servicing to avoid electrical shock. Steps: Unplug the washer and remove the rear access panel. Locate the old drive belt and remove it from the motor and drum pulleys. Position the new XPARTCO 5304516132 belt around the drum pulley first. Stretch the belt onto the motor pulley while rotating the drum. Reinstall the back panel, restore power, and test wash/spin cycles. ⏱️ Time Required: 10–20 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Restore smooth washer performance — Add to Cart Now for a dependable, affordable repair!

Read more less

WP21352320 Genuine OEM Whirlpool Washer Drive Belt The WP21352320 is a genuine Whirlpool OEM drive belt for Whirlpool top-load washers. This belt connects the drive motor to the transmission at the bottom of the washer, and it's what actually spins the basket during the wash and spin cycles. Unlike a dryer's drum belt, which simply tumbles a drum, this washer drive belt has to transfer real torque to spin a heavy, water-filled basket, which puts it under considerably more mechanical stress. Measuring approximately 51" long and 3/8" wide. A worn or broken belt produces a distinctive set of symptoms: the washer may not spin at all, spin only slowly, agitate poorly or not at all, fail to drain properly since the pump relies on the same drive system, or produce a burning smell or loud grinding noise as a worn belt slips against the pulley. One useful diagnostic tip worth knowing: a belt can look intact at a glance but still be worn out — if the sides of the belt appear shiny or glazed rather than matte, that's a sign of slippage-related wear even without a visible crack. It directly replaces 21001478, 21352320, 35-2073, 35-2320, AP6005822, WP21352320VP, and PS11738882. Quick Answer The WP21352320 Genuine OEM Whirlpool Washer Drive Belt fixes Whirlpool, Maytag, Roper, Admiral, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, Norge, Amana, Kenmore, KitchenAid, and Ikea top-load washers with a drum that won't spin, spins slowly, won't agitate, won't drain, or produces a burning smell or loud grinding noise. Approximately 51" long, 3/8" wide. Replaces 21001478, 21352320, 35-2073, 35-2320, AP6005822, WP21352320VP, PS11738882. A belt can look intact but still be worn out — check the sides for a shiny, glazed appearance, which indicates slippage wear even without a visible crack. Common Problems This Part Fixes Washer drum won't spin, or spins only slowly Washer won't agitate during the wash cycle Washer won't drain properly Burning smell coming from the washer during operation Loud grinding noise from underneath the washer Washer that shakes or moves excessively during spin Washer that won't start or stalls partway through a cycle Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer drive belt directly replaces the following OEM and cross-reference part numbers: WP21352320, 21352320, 21001478, 35-2073, 35-2320, 35-3662, PD00002418, EAP11738882, AP6005822, AWP46532, PS11738882, WP21352320VP If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drive belt is compatible with select Whirlpool top-load washers, and also fits select Maytag, Roper, Admiral, Hardwick, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, Norge, Modern Maid, Amana, Kenmore, KitchenAid, and Ikea washers built on the Whirlpool platform, including model numbers such as HAV3460AWW. Note: Always verify your full model number before ordering, since Whirlpool uses several different drive belts across its top-load washer lineup. Contact our support team with your model number if you're unsure. Key Features Genuine Whirlpool OEM part — factory-specified length, width, and material Connects the drive motor to the transmission to spin the basket Resolves "won't spin," "won't agitate," "won't drain," "burning smell," and "grinding noise" symptoms caused by belt failure Approximately 51" long, 3/8" wide Direct drop-in replacement matching the original belt routing Replaces 21001478, 21352320, 35-2073, 35-2320, AP6005822, WP21352320VP, and PS11738882 Compatible with Whirlpool, Maytag, Roper, Admiral, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, Norge, Amana, Kenmore, KitchenAid, and Ikea top-load washers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number WP21352320 Part Type Washer Drive Belt Condition Genuine OEM Brand Whirlpool Application Top-Load Washers Length Approx. 51 in. Width 3/8 in. Attaches To Motor pulley and transmission Repair Difficulty Medium — basic hand tools required Quantity 1 drive belt Compatible Brands Whirlpool, Maytag, Roper, Admiral, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, Norge, Amana, Kenmore, KitchenAid, Ikea Installation Notes ⚠️ Unplug Washer And Shut Off Water Supply Before Starting — Consider The Motor Pulley While You're In There Disconnect power at the outlet or shut off the circuit breaker, and shut off both the hot and cold water supply valves before beginning. Pull the washer out from the wall for full access. Wear work gloves. Locate the drive belt around the motor at the bottom of the washer. Use a flathead screwdriver or hex wrench to remove the screws holding the motor bracket in place, which releases tension on the belt. Carefully slide the motor bracket off the motor, and use pliers if needed to work the old belt off the pulley. While the bottom of the washer is accessible, this is a good time to inspect the motor pulley for wear as well, since it's a related component you'll already have exposed. Install the new WP21352320 belt around the pulley and transmission, following the same routing as the old belt, and make sure it's seated securely and tightened properly — a loose or improperly seated belt will slip and wear out quickly. Reattach the motor bracket with its screws. Restore the water supply and power, then run a test cycle to confirm the washer spins, agitates, and drains normally with no unusual noise. Tools needed: multi-bit screwdriver, hex wrench, standard pliers, work gloves. Frequently Asked Questions My belt looks fine — no cracks or visible damage. Could it still need replacing? Yes, and this is a common source of confusion. A belt can appear intact with no cracks and still be worn out. Check the sides of the belt closely: if they look shiny or glazed rather than having a matte, textured surface, that glazing indicates the belt has been slipping against the pulley, which is a clear sign of wear even without visible cracking. My washer pumps and drains but the drum spins slowly or not at all. Is this the belt? Yes, this is one of the most direct symptoms of a worn or slipping drive belt. Since this belt is what actually transfers the motor's power to spin the basket, a worn belt can slip under load, causing slow or absent spinning even though the motor itself and the drain pump are both working normally. Should I replace the motor pulley at the same time? It's worth inspecting while you have the bottom of the washer accessible, even if you don't end up replacing it. A worn pulley can accelerate wear on a brand-new belt, so checking its condition during this repair is a reasonable precaution, especially if your old belt showed the glazed, slipping-related wear pattern. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original length, width, and routing configuration of the drive belt originally installed in your washer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

W10775188 Washer Genuine OEM Washplate Replaces Part Numbers: W10775188, 4282681, W10698538, W10834891, AP5959417, PS11699797. W10775188 Washer Washplate – Genuine OEM Part Restore optimal cleaning power with the W10775188 Washer Washplate. This Genuine OEM part replaces a worn or damaged washplate to ensure efficient agitation and even cleaning performance. Key Features: ✅ Genuine OEM Part – built to factory specs 🔁 Replaces: 4282681, W10698538, W10834891, AP5959417, PS11699797 🌀 Provides powerful agitation for deep cleaning 🛠️ Fits select Whirlpool, Maytag, and Amana top-load washers 🧰 Easy to install – includes center bolt ⚠️ Always unplug your washer before servicing. Need help with compatibility? Contact us! 📦 Part Number: W10775188

Read more less

WP3363003 Washer Upper Agitator Fits Specific Top Load Washer Models. Replaces Part Number: WP3363003, 3363003, 2654, AP6008106, PS11741237. Description: The Upper Agitator is an OEM part designed for select Kenmore, Whirlpool top-loading washing machines. 

Read more less

DC31-20014C Washer Genuine OEM Shift Actuator This clutch (part number DC31-20014C) is for washers. Clutch DC31-20014C spins the basket during the spin cycle. Fits specific Samsung washer Models Replaces Part Numbers:DC31-20014C, 2068406, AP4211210, PS4204941.   California Residents only: WARNING: California’s Proposition 65

Read more less

WH16X26913 Washer Genuine OEM Suspension Rod and Spring Rod and spring asm right- black Description: The Rod and Spring Asm Right-Black is an OEM replacement part for GE washing machines. It is responsible for providing the necessary tension and support for the washer drum. This assembly includes a durable rod and spring that work together to balance the drum and minimize excessive vibrations during the wash and spin cycles. Replaces Parts Numbers: WH16X26913, WH16X26714, AP6331892, PS12343383. California Residents only WARNING: California’s Proposition 65 

Read more less

4 Pack - XPARTCO 8182703 Washer Shock Absorber Replaces WP8182703 The XPARTCO 8182703 is an aftermarket replacement front-load washer shock absorber compatible with select Whirlpool, Maytag, Kenmore, KitchenAid, Amana, Jenn-Air, Admiral, and Roper front-load washers in the GHW, WFW, MHWE, MFW, and KHWS series. The shock absorber is a hydraulic dampener that connects the outer washer tub to the base frame. During the spin cycle, the shock absorbers absorb and dampen the vibrations and movement generated by the spinning drum — keeping the washer stable, quiet, and protecting internal components from damage caused by excessive movement. Most compatible Whirlpool-family front-load washers use four shock absorbers — two at the front and two at the rear. When one or more shock absorbers wear out, the outer tub vibrates excessively, causing loud banging or thumping during the spin cycle. It is strongly recommended to replace all four shock absorbers at the same time. This listing is for a single shock absorber. It directly replaces WP8182703, 8181646, 1173231, and several additional cross-reference numbers. Installs in 30–45 minutes with basic hand tools. Quick Answer The XPARTCO 8182703 Washer Shock Absorber fixes front-load washers that shake violently, bang loudly, or walk across the floor during the spin cycle. The shock absorber dampens tub vibration. Most models use 4 shock absorbers — replace all 4 at the same time. Sold individually. Compatible with Whirlpool, Maytag, Kenmore, KitchenAid, Amana, Jenn-Air, Admiral, and Roper front-load washers. Replaces WP8182703, 8181646, AP6011831, and more. Common Problems This Part Fixes Violent shaking or vibrating during the spin cycle Loud banging, thumping, or clunking noise during spin Washer "walking" across the floor during the spin cycle Outer tub hitting the sides of the cabinet during high-speed spin Spin cycle errors caused by excessive tub movement triggering the imbalance sensor Visible oil leak, broken mount, or collapsed shock absorber body Washer repeatedly pausing spin cycle and redistributing the load without resolving the vibration Replaces Part Numbers This shock absorber directly replaces the following OEM and cross-reference part numbers: WP8182703, 8182703, 1173231, 8181646, EAP11745030, AWP48892, PD00003153, AP6011831, PS11745030. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This shock absorber is compatible with select front-load washers from the following brands and series: Whirlpool front-load washers — GHW and WFW series Maytag front-load washers — MHWE and MFW series Kenmore / Sears front-load washers (select Whirlpool-built models) KitchenAid front-load washers — KHWS series Amana front-load washers Jenn-Air front-load washers Admiral front-load washers Roper front-load washers Important: Most compatible models use 4 shock absorbers (2 front, 2 rear). This part is sold individually. It is strongly recommended to replace all 4 at the same time, as the remaining absorbers have experienced the same wear and will fail soon after. Key Features Hydraulic dampener that connects the outer washer tub to the base frame — absorbs spin cycle vibration and prevents tub-to-cabinet contact Keeps the washer stable and quiet during high-speed spin cycles, protecting drum bearings, seals, and cabinet from premature wear High-quality reinforced construction — excellent toughness, oil resistance, and resistance to weak acids and alkalis for long service life Direct replacement for WP8182703 and 8181646 — no modification required Compatible with Whirlpool GHW, WFW, Maytag MHWE, MFW, and KitchenAid KHWS series front-load washers Sold individually — most models require 4 shock absorbers; replace all 4 at the same time Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 30–45 minutes with basic hand tools Product Specifications Part Number 8182703-4PK OEM Part Number WP8182703 Part Type Front-Load Washer Shock Absorber (Hydraulic Dampener) Condition Aftermarket Replacement Application Front-Load Washers Quantity Per Washer 4 (2 front, 2 rear) Compatible Brands Whirlpool, Maytag, Kenmore, KitchenAid, Amana, Jenn-Air, Admiral, Roper Compatible Series GHW, WFW, MHWE, MFW, KHWS Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting Unplug the washer and turn off the water supply before beginning. To access the front shock absorbers, remove the lower front access panel. To access the rear shock absorbers, pull the washer away from the wall, disconnect the water hoses, and remove the rear panel. The shock absorbers connect the outer tub to the base frame with mounting pins at the top and bottom — turn the shock absorber 90 degrees at both pins to release and remove it. Install the new 8182703 shock absorber by inserting the pins into the top and bottom mounting brackets and rotating 90 degrees to lock in place. Replace all 4 shock absorbers during the same repair. Reconnect all panels and water hoses, plug in the washer, restore water supply, and run a spin cycle to verify normal operation. Work gloves are recommended as there are sharp edges inside the cabinet. Tools needed: Phillips screwdriver, channel-lock pliers, work gloves. Frequently Asked Questions What does the washer shock absorber do? The shock absorbers are hydraulic dampeners that connect the outer washer tub to the base frame of the machine. During the spin cycle — when the drum spins at high speeds — the shock absorbers absorb and dampen the vibrations and movement of the heavy outer tub, keeping it centered and preventing it from striking the sides of the washer cabinet. Without functioning shock absorbers, the washer vibrates violently, makes loud banging noises, and can "walk" across the floor during spin, potentially damaging internal components over time. How many shock absorbers does my front-load washer have? Most Whirlpool-family front-load washers compatible with the 8182703 shock absorber use four shock absorbers — two mounted at the front of the tub and two at the rear. This listing is for a single shock absorber. When replacing shock absorbers, it is strongly recommended to replace all four at once, as they all experience the same amount of use and the remaining absorbers are likely to fail soon after the first one. What is the difference between 8182703 and WP8182703? These are the same shock absorber. WP8182703 is the updated Whirlpool OEM part number that superseded the original 8182703. The 8181646 is also a cross-reference to this same part. This aftermarket replacement is compatible with all three numbers. My washer still vibrates after replacing the shock absorbers — what else could it be? If vibration persists after replacing all four shock absorbers, other possible causes include an unbalanced or overloaded drum, worn drum bearings, a failing suspension spring, or the washer not being level on the floor. Check that the washer's leveling feet are adjusted so all four corners are in firm contact with the floor. Also confirm the load is not oversized — overloading is the most common cause of spin vibration and can prematurely wear shock absorbers. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured from high-quality reinforced materials to match the dimensions and performance of the original WP8182703 shock absorber. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less