Washer Parts

Choice 280187 Washer Drain Pump Assembly The Choice 280187 is an aftermarket replacement front-load washer drain pump and motor assembly compatible with a wide range of Whirlpool, Maytag, KitchenAid, Kenmore, Amana, Jenn-Air, Roper, Admiral, Norge, and Magic Chef front-load washers — including the Whirlpool Duet GHW and WFW series, Maytag Epic MFW series, Maytag MHWE and NFW series, and Kenmore HE front-load washers. The drain pump removes water from the washer tub during the drain portion of each wash cycle. When the pump fails, the washer will not drain, will leave standing water in the tub, stop mid-cycle, display error code F21, or make unusual noise during the drain phase. This complete assembly includes the Askoll M75-compatible pump motor, motor impeller, pump housing with filter, and mounting grommets. Rated 120V, 60Hz, 70W, 1.0A with a 15-minute on / 45-minute off duty cycle. Dimensions: 10-1/4"L x 6-1/4"W x 5-1/4"H. It directly replaces 285998, 8181684, 8182819, 8182821, 1200164, Askoll M75, LP280187, AP3953640, AH1485610, EA1485610, EAP1485610, PD00002352, and PS1485610. Always check and clear the pump filter/coin trap before replacing the pump — a clogged filter is among the most common causes of F21 errors. Installs in 15–30 minutes with basic hand tools. Quick Answer The Choice 280187 Washer Drain Pump Assembly fixes Whirlpool Duet, Maytag Epic, and Kenmore HE front-load washers that won't drain, leave standing water, display error code F21, or make loud humming or grinding noises during the drain cycle. Complete assembly — motor, impeller, housing, filter, and grommets. 120V/60Hz/70W/1.0A. 15 min on / 45 min off. 10-1/4"L x 6-1/4"W x 5-1/4"H. Replaces 285998, 8181684, 8182819, 8182821, 1200164, Askoll M75, AP3953640, PS1485610. Check filter before replacing pump. Common Problems This Part Fixes Washer not draining — standing water remaining in the tub after a cycle Error code F21 displayed — long drain fault (washer unable to drain within allotted time) Washer stopping mid-cycle due to a drain fault Loud humming during the drain phase — motor running but impeller not pumping Grinding or rattling noise during drain — damaged impeller or worn pump bearings Clothes excessively wet after a cycle — pump not fully removing water before spin Water draining very slowly — worn pump motor below rated performance Water leaking from the pump area at the front of the washer Replaces Part Numbers This drain pump directly replaces the following OEM and cross-reference part numbers: 280187, 1200164, 285998, 8181684, 8182819, 8182821, AH1485610, AP3953640, AWP39453, EA1485610, EAP1485610, PD00002352, PS1485610. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drain pump is compatible with select front-load washers from the following brands and series: Whirlpool front-load washers — Duet GHW series (GHW9100L, GHW9150P, GHW9160P, GHW9200L, GHW9250M, GHW9300P, GHW9400P, GHW9400SU0, GHW9460P and related models) Whirlpool front-load washers — Duet WFW series (WFW9200S, WFW9300V, WFW9400S, WFW9400V, WFW9410X and related models) Maytag front-load washers — Epic MFW series (MFW9600SQ0, MFW9600SQ1, MFW9700S, MFW9800TK0, MFW9800TQ0 and related models) Maytag front-load washers — MHWE series (MHWE300V, MHWE400W, MHWE450W, MHWE500VW, MHWE550W, MHWE950W and related models) Maytag front-load washers — NFW series (NFW7500V, NFW7600XW00 and related models) KitchenAid front-load washers — KHWS series (KHWS01PM, KHWS02R and related models) Kenmore / Sears front-load washers — HE series (select 110-series Whirlpool-built models) 7M series front-load washers (7MGHW9100MW0, 7MGHW9150, 7MGHW9400 and related models) Amana, Jenn-Air, Roper, Admiral, Norge, and Magic Chef front-load washers (select models) Important: Before replacing the pump, check and clear the pump filter/coin trap behind the lower front access panel — a clogged filter is a very common cause of F21 errors and slow draining that does not require pump replacement. Always verify your model number before ordering. Key Features Removes water from the tub during drain and spin cycles for proper washer operation Complete assembly — Askoll M75-compatible motor, impeller, pump housing with filter, mounting grommets, and hardware included Rated 120V, 60Hz, 70W, 1.0A — correct electrical specifications for compatible front-load washer models Duty cycle: 15 minutes on / 45 minutes off — matches original pump operating requirements Dimensions: 10-1/4"L x 6-1/4"W x 5-1/4"H Resolves error code F21 (long drain fault) on compatible Whirlpool Duet, Maytag Epic, and Kenmore HE models Replaces 285998, 8181684, 8182819, 8182821, 1200164, Askoll M75, AP3953640, and PS1485610 Compatible with Whirlpool GHW/WFW Duet, Maytag Epic/MHWE/NFW, KitchenAid KHWS, and Kenmore HE front-load washers Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 15–30 minutes with basic hand tools Product Specifications Part Number 280187CM Part Type Front-Load Washer Drain Pump and Motor Assembly Condition Aftermarket Replacement Application Front-Load Washers — Whirlpool Duet, Maytag Epic/MHWE/NFW, Kenmore HE Motor Askoll M75-compatible Voltage 120V AC Frequency 60 Hz Wattage 70W Amperage 1.0A Duty Cycle 15 minutes on / 45 minutes off Dimensions 10-1/4"L x 6-1/4"W x 5-1/4"H Color White / Black / Gray / Red Material Metal / Plastic Housing / Rubber Includes Pump motor, impeller, housing with filter, rear grommets, front grommets, hardware Error Code Resolved F21 (long drain fault) Compatible Brands Whirlpool, Maytag, KitchenAid, Kenmore, Amana, Jenn-Air, Roper, Admiral, Norge, Magic Chef Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off the water supply before beginning. Place towels on the floor in front of the washer — residual water will drain from the pump when it is disconnected. The drain pump is accessed from the lower front panel. Remove the screws from the lower kick panel to expose the pump access area. Before removing the pump, drain residual water by removing the pump filter cap (have a shallow pan ready). After draining, disconnect the pump wiring harness. Release the hose clamps and pull the drain hoses free from the pump ports. Unscrew the pump mounting screws or twist out the mounting grommets. Remove the old pump and install the new 280187 assembly in the same position using the included grommets. Reconnect hoses, secure clamps, and reconnect the wiring harness. Reinstall the kick panel. Restore power and water and run a drain/spin cycle to verify drainage and check for leaks. Tools needed: Phillips screwdriver, pliers, shallow pan, towels. Frequently Asked Questions What does error code F21 mean on Whirlpool Duet and Maytag front-load washers? F21 indicates a long drain fault — the washer was unable to drain within the expected time (typically 8 minutes). Before replacing the pump, check and clean the pump filter/coin trap at the lower front of the washer — lint, coins, and debris in the filter restrict flow and are a very common cause of F21 errors. If the filter is clean and the error persists, the drain pump motor has likely failed and needs replacement. What is the Askoll M75 motor and why is it referenced? The original 280187 drain pump used an Askoll M75 motor — Askoll is an Italian motor manufacturer that supplies drain pump motors to Whirlpool for use in Duet, Maytag Epic, and related front-load washers. Aftermarket replacements for the 280187 are often described as "Askoll M75 compatible" to confirm they are designed as drop-in replacements for pumps using that motor. The Choice 280187 drain pump is manufactured to match the performance specifications of the original Askoll M75-based assembly. What is the difference between 280187 and 8182821 or 8181684? These are all part numbers for the same front-load washer drain pump assembly across different production runs and naming conventions. 285998, 8181684, 8182819, and 8182821 are earlier cross-references for this pump from Whirlpool's parts catalog, and 280187 is the current consolidated part number. The 1200164 is an additional cross-reference. This aftermarket replacement covers all of them. Should I check the pump filter before replacing the pump? Yes — always check the pump filter first. On compatible Whirlpool Duet, Maytag Epic, and Kenmore HE front-load washers, the pump filter is accessible behind the lower front kick panel. Remove the cap, drain residual water into a pan, and remove any debris from the filter. If the filter was clogged and the error clears after cleaning, pump replacement is not needed. If the filter is clear and the F21 error persists, or if the pump makes loud noise or leaks, then pump replacement is required. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured with an Askoll M75-compatible motor to match the electrical specifications and performance of the original 280187 drain pump assembly. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

6601EN1003D Washer Door Lock Interlock Switch Replaces Part Numbers: 6601EN1003D, 6601ER1005A, 2651099, AH3636296, AP5594317, EA3636296, PS3636296.   This is an aftermarket part that can be used as a replacement for the OEM part. WARNING: California’s Proposition 65 (California Residents Only)

Read more less

8540101CM Washer Drive Belt Washing machine inner tub drive belt 6 Rib, 51.33" Description: The Drive Belt is a replacement for specific Whirlpool, Maytag, Kenmore washer models. It transmits power from the washer motor to the tub, causing it to rotate during wash and spin cycles Causes of a worn drive belt can include repetitive cycles over years of use. The belt undergoes stress each time the tub is set in motion. Damage from slipping off pulleys during operation can also affect the belt. Replaces Part NumbersWP8540101, 8540101, 8540348, AP6013037, PS11746258 This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: California’s Proposition 65 

Read more less

ERP DC97-05280W Washer Suspension Rod Replaces Part Numbers: DC97-05280W, 3998024, AP5966911, PS11719937   This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

XPARTCO W10730972 Washer Drain Pump Replaces WPW10730972 The XPARTCO W10730972 is an aftermarket replacement front-load washer drain pump and motor assembly compatible with a wide range of Whirlpool, Maytag, Kenmore, Amana, Inglis, and KitchenAid front-load washers — including the Whirlpool Duet, Maytag 2000/3000/4000 series, and Kenmore HE2/HE2T Plus. The drain pump removes water from the washer tub during the drain and spin phases of each wash cycle. When the pump fails, the washer will not drain, will leave standing water in the tub, stop mid-cycle, display error codes F21, F33, or SD, or leak from the pump area. This complete assembly includes the motor, pump housing, and integrated filter — these components are only available as a complete assembly and are not sold separately. Rated 120V, 60Hz, 78W, 1.2A (CL.F duty class). Assembly dimensions are 8-3/4"L x 7"W x 5-1/4"H in off-white plastic housing. Note: Whirlpool redesigned this pump — the replacement may look different from the original but fits and functions identically. It directly replaces WPW10730972, W10130913, W10130913-B, 8540024, 8540025, 8540027, 8540028, 8540996, W10117829, W10183434, W10190647, W10190648, W10201457, AP6023956, PS11757304, and additional cross-reference numbers. Installs in 20–30 minutes with basic hand tools. Quick Answer The XPARTCO W10730972 Washer Drain Pump fixes Whirlpool Duet, Maytag 2000/3000/4000 series, and Kenmore HE2/HE2T Plus front-load washers that won't drain, leave standing water, or display error codes F21, F33, or SD. Complete assembly — motor, pump housing, and filter included. 120V/60Hz/78W/1.2A. 8-3/4"L x 7"W x 5-1/4"H. Note: redesigned — may look different from original but fits identically. Replaces WPW10730972, W10130913, 8540024, 8540996, W10117829, AP6023956, PS11757304. Common Problems This Part Fixes Washer not draining — standing water remaining in the tub after a cycle Error code F21 displayed — long drain fault (washer unable to drain in allotted time) Error code F33 displayed — pump motor fault Error code SD displayed — suds detection or drain issue Washer stopping mid-cycle due to a drain fault Loud humming or grinding noise during the drain phase Water leaking from the front lower area of the washer — pump seal failure Pump motor running but water not being expelled from the tub Replaces Part Numbers This drain pump directly replaces the following OEM and cross-reference part numbers: WPW10730972, W10730972, W10130913, 4281917, 8540024, 8540025, 8540027, 8540028, 8540996, W10117829, W10183434, W10190647, W10190648, W10201457, WPW10730972VP, AP6023956, AWP50633, B40-3A01, EAP11757304, PD00025949, PS11757304 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drain pump is compatible with select front-load washers from the following brands and series: Whirlpool front-load washers — Duet series (WFW8300, WFW8400, WFW9050, WFW9150, WFW9200, WFW9250, WFW9400, WFW9450, WFW9500, WFW9550, WFW9600, WFW96HEA, WFW97HED, WFW98HEB and related models) Maytag front-load washers — 2000 series (MHW2000AW, MHW2000BWW and related models) Maytag front-load washers — 3000 series (MHW3000BW and related models) Maytag front-load washers — 4000 series (MHW4000BW, MHW4200BW, MHW5100DW, MHW6000AW, MHW6000XW and related models) Kenmore / Sears front-load washers — HE2 and HE2T Plus series (110.45862400, 110.47532602 and related models) Amana front-load washers (select models) Inglis front-load washers (select models) KitchenAid front-load washers (select models) Note: Whirlpool redesigned this pump assembly — the replacement may look different from your original pump (larger in size on some versions) but is engineered to fit and function identically in all compatible models. Always verify your model number before ordering. Before replacing the pump, check and clear the coin trap/drain filter — a clogged filter is a common cause of F21/F33 errors that does not require pump replacement. Key Features Removes water from the tub during drain and spin cycles — essential for proper washer operation Complete assembly — motor, pump housing, and integrated filter included; components are not sold separately Rated 120V, 60Hz, 78W, 1.2A (CL.F) — correct electrical specifications for compatible Whirlpool-family front-load washers Dimensions: 8-3/4"L x 7"W x 5-1/4"H — off-white plastic housing Resolves error codes F21 (long drain), F33 (pump motor fault), and SD (suds/drain) on compatible models Redesigned assembly — may look different from original but fits and functions identically Replaces WPW10730972, W10130913, 8540024, 8540996, W10117829, AP6023956, and over 20 additional cross-references Compatible with Whirlpool Duet, Maytag 2000/3000/4000 series, Kenmore HE2/HE2T Plus, Amana, Inglis, and KitchenAid Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 20–30 minutes with basic hand tools Product Specifications Part Number XPW10730972 OEM Part Number WPW10730972 Part Type Front-Load Washer Drain Pump and Motor Assembly Condition Aftermarket Replacement Application Front-Load Washers (Duet, Maytag 2000/3000/4000, Kenmore HE2/HE2T Plus) Voltage 120V AC Frequency 60 Hz Wattage 78W Amperage 1.2A Duty Class CL.F Dimensions 8-3/4"L x 7"W x 5-1/4"H Color Off-White Material Plastic housing Includes Motor, pump housing, and integrated filter — complete assembly Design Note Redesigned — may look different from original; fits identically Error Codes Resolved F21 (long drain), F33 (pump motor fault), SD (suds/drain) Compatible Brands Whirlpool, Maytag, Kenmore, Amana, Inglis, KitchenAid Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting — Work Gloves Recommended Disconnect power and turn off the water supply before beginning. Place towels on the floor — residual water will drain when the pump is disconnected. The drain pump is accessed through the lower front panel of the washer. Remove the screws on the lower kick panel or snap panel to expose the pump access area. Before removing the pump, drain residual water by removing the coin trap/filter cap from the filter housing (have a shallow pan ready — up to a quart of water may flow out). After draining, disconnect the pump wiring harness. Release the drain hose clamps and disconnect the hoses from the pump. Unscrew or unclip the pump mounting hardware and remove the old pump. Transfer the hoses and wiring to the new W10730972 pump, secure the mounting hardware, and reinstall the front panel. Restore power and water, run a drain/spin cycle, and check for leaks. Tools needed: Phillips screwdriver, Torx screwdriver (T20 on some models), pliers, shallow pan, towels, work gloves. Frequently Asked Questions What do error codes F21, F33, and SD mean on Whirlpool Duet and Maytag washers? F21 indicates a long drain fault — the washer was unable to drain within the expected time (typically 8 minutes). F33 indicates a pump motor fault — the control board is not detecting the pump motor operating correctly. SD is a suds detection code that can also appear when drain issues prevent the suds from clearing properly. All three codes point toward the drain pump or a drain obstruction. Before replacing the pump, check and clean the coin trap filter — a clogged filter is one of the most common causes of F21 errors and clearing it often resolves the code without needing a new pump. Should I check the coin trap filter before replacing the pump? Yes — always check the coin trap filter before replacing the pump. On Whirlpool Duet and Maytag front-load washers, the coin trap filter is located inside the lower front access panel, typically behind a small cap or cover. Removing the cap and clearing lint, coins, and debris from the filter restores drain flow and clears F21/F33 errors in many cases without any part replacement needed. If the filter is clear and the pump still humbles or fails to drain, the pump needs replacement. Why does the replacement pump look different from the original? Whirlpool redesigned this drain pump assembly during its production lifecycle — the WPW10730972 replacement is physically larger than some of the older 8540024-series pumps it supersedes. Despite looking different, the redesigned pump uses the same hose and electrical connection points and is a direct fit in all compatible models. The larger housing is an intentional design improvement to increase pumping capacity. If the pump looks bigger than what you removed, this is normal and expected — install it in the same way as the original. What is the difference between W10730972 and WPW10730972? These are the same drain pump assembly. WPW10730972 is the updated Whirlpool OEM part number that superseded the original W10730972. The W10130913 and 8540024 are also cross-references for earlier versions of this same pump. This aftermarket replacement is compatible with all of these numbers. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the electrical specifications and performance of the original WPW10730972 drain pump assembly. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less