Washer Parts

6601EN1003D Washer Door Lock Interlock Switch Replaces Part Numbers: 6601EN1003D, 6601ER1005A, 2651099, AH3636296, AP5594317, EA3636296, PS3636296.   This is an aftermarket part that can be used as a replacement for the OEM part. WARNING: California’s Proposition 65 (California Residents Only)

Read more less

8540101CM Washer Drive Belt Washing machine inner tub drive belt 6 Rib, 51.33" Description: The Drive Belt is a replacement for specific Whirlpool, Maytag, Kenmore washer models. It transmits power from the washer motor to the tub, causing it to rotate during wash and spin cycles Causes of a worn drive belt can include repetitive cycles over years of use. The belt undergoes stress each time the tub is set in motion. Damage from slipping off pulleys during operation can also affect the belt. Replaces Part NumbersWP8540101, 8540101, 8540348, AP6013037, PS11746258 This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: California’s Proposition 65 

Read more less

ERP DC97-05280W Washer Suspension Rod Replaces Part Numbers: DC97-05280W, 3998024, AP5966911, PS11719937   This is an aftermarket part that can be used as a replacement for the OEM part. California Residents only WARNING: Cancer and/or Reproductive Harm - www.p65warnings.ca.gov

Read more less

WP389140 Genuine OEM Whirlpool Washer Drive Block The WP389140 is a genuine Whirlpool OEM drive block for large-capacity belt-drive and direct-drive top-load washers. This is a purely mechanical coupling component: it connects the inner spin basket to the transmission's drive shaft, so that when the transmission turns, the basket turns with it. Without a properly seated drive block, the connection between the motor's rotational power and the basket is lost or unreliable, even though every electrical component in the washer may be working perfectly. Measuring approximately 2-5/16" high, this drive block is a wear component subject to gradual mechanical stress every time the washer agitates or spins. A worn or failed drive block produces a distinctive set of symptoms: the basket may spin freely without properly engaging, the washer may spin slowly and leave clothes excessively wet, or you may hear a loud knocking or banging noise during operation as the connection between the basket and drive shaft becomes loose or worn. It directly replaces 389140, AP6008836, 357782, 97360, J27-936, PS11741977, PS349903, AP2905773, WH40X180, WP389140VP, LP16171, and 2858. Quick Answer The WP389140 Genuine OEM Whirlpool Washer Drive Block fixes Whirlpool, Kenmore, Maytag, KitchenAid, Roper, Admiral, Amana, Crosley, Estate, and Inglis top-load washers with a basket that spins freely without engaging, slow spinning that leaves clothes excessively wet, or loud knocking/banging noise during operation. Approximately 2-5/16" high. For large-capacity belt-drive and direct-drive washers. Replaces 389140, AP6008836, 357782, 97360, J27-936, PS11741977, PS349903, AP2905773, WH40X180, WP389140VP, LP16171, 2858. This repair typically requires a spanner wrench to remove a large securing nut — budget for the right tool before starting. Common Problems This Part Fixes Washer basket spins freely without properly engaging during the wash or spin cycle Washer spins slowly, leaving clothes excessively wet at the end of a cycle Loud knocking or banging noise during operation Washer shakes or moves noticeably during spin Basket continues spinning after the cycle should have stopped Inefficient wash and spin cycles overall due to poor basket engagement Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer drive block directly replaces the following OEM and cross-reference part numbers: WP389140, 389140, 357782, 97360, PD00002363, EAP11741977, WP389140VP, AP6008836, AWP47839, J27-936, PS11741977. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drive block is compatible with select Whirlpool large-capacity top-load washers (belt-drive and direct-drive), and also fits select Kenmore, Maytag, KitchenAid, Roper, Admiral, Amana, Crosley, Estate, and Inglis washers built on the Whirlpool platform, including model numbers such as: NTW4516FW, NTW4516FW3, NTW4516FW4 WTW4816FW2, WTW4816FW3 RTW4516FW, NTW4605EW, WTW4800BQ Note: Always verify your full model number before ordering, since Whirlpool uses different drive block designs across its washer lineup. Contact our support team with your model number if you're unsure. Key Features Genuine Whirlpool OEM part — factory-specified fit for a secure basket-to-transmission connection Connects the inner spin basket to the transmission's drive shaft Resolves "basket spins freely," "slow spin, clothes too wet," and "loud knocking noise" symptoms caused by drive block wear Approximately 2-5/16" high Designed for large-capacity belt-drive and direct-drive washer platforms Direct drop-in replacement matching the original fit onto the spin tube notches Replaces 389140, AP6008836, 357782, 97360, J27-936, PS11741977, PS349903, AP2905773, WH40X180, WP389140VP, LP16171, and 2858 Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Roper, Admiral, Amana, Crosley, Estate, and Inglis washers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number WP389140 Part Type Washer Drive Block Condition Genuine OEM Brand Whirlpool Application Large-Capacity Belt-Drive and Direct-Drive Top-Load Washers Height Approx. 2-5/16 in. Function Connects the inner spin basket to the transmission drive shaft Related Component Drive cam (commonly inspected/replaced during the same repair) Repair Difficulty Moderate — spanner wrench and washer disassembly required Quantity 1 drive block Compatible Brands Whirlpool, Kenmore, Maytag, KitchenAid, Roper, Admiral, Amana, Crosley, Estate, Inglis Installation Notes ⚠️ Unplug Washer And Shut Off Water Supply Before Starting — Spanner Wrench Required Disconnect power at the outlet or shut off the circuit breaker, and shut off the hot and cold water supply valves before beginning. Wear work gloves. Remove the washer's top and control console per your model's service instructions to access the inner tub assembly. Remove the agitator and any hardware securing the basket, which typically includes a large center nut — a spanner wrench is required to remove this nut, along with a socket and long extension for other fasteners; expect to remove a fair number of components to fully access the drive block. Lift the wash basket out to expose the drive block, which sits on the spin tube near the center of the transmission. Photograph the orientation of the old drive block and any surrounding hardware before removing it. Lift the old drive block free, and while it's accessible, inspect the drive cam nearby for wear as well, since it's commonly replaced at the same time. Slide the new WP389140 drive block into position, making sure it seats fully onto the spin tube notches, and reassemble the basket, hardware, agitator, console, and top panel in reverse order. Restore water and power, then run a test cycle through both wash and spin to confirm the basket engages properly with no unusual noise. Tools needed: multi-screwdriver, spanner wrench, socket set with long extension, work gloves. Frequently Asked Questions My washer basket spins freely and doesn't seem connected to anything. Is this the drive block? Yes, this is the classic symptom of a failed drive block. Since this component is the mechanical link between the transmission's drive shaft and the inner spin basket, once it wears out or fails, the basket can spin independently without properly engaging, even though the motor and transmission are working normally. Do I really need a spanner wrench for this repair? Yes, on most models. Accessing the drive block requires removing a large nut that secures the basket assembly, and this nut is specifically designed to be removed with a spanner wrench rather than a standard socket. Trying to remove it without the correct tool risks damaging the nut or the surrounding components, so it's worth having one on hand before you start. Should I replace the drive cam at the same time? It's worth inspecting while you have the assembly open, since the drive cam sits in the same area and is commonly replaced alongside the drive block when a technician is already this far into the repair. If it shows visible wear, replacing both at once saves you from repeating this same teardown again soon after. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original dimensions and fit of the drive block originally installed in your washer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

Genuine OEM WPW10453947 Washer or Dryer Control Knob  The Genuine OEM WPW10453947 is a factory-original control knob used on both washers and dryers across the Whirlpool platform — the same knob design is shared between select top-load washer cycle-selector dials and dryer cycle/timer dials, depending on the model. It mounts onto the control shaft on the console and is what the user grips to select a wash or dry cycle. Over time these knobs commonly crack, the D-shaped shaft-grip inside wears out and starts spinning freely on the shaft, or the knob's pointer/indicator fades or breaks off. As the genuine Whirlpool part, it matches the factory shaft profile, detent feel, and indicator marking of the original equipment, so there's no fit or cosmetic mismatch. It directly replaces W10453947, 2304653, AP5607287, AWP50246, EAP3632979, PD00008425, PS3632979. Installs in under 5 minutes with no tools required — it's a simple push-on friction fit in most applications. Quick Answer The Genuine OEM WPW10453947 Washer or Dryer Control Knob fixes Whirlpool, Amana, Admiral, Inglis, Roper, Kenmore, Crosley, and Maytag washers and dryers with a cracked, spinning, or missing cycle-selector knob. This is the factory-original Whirlpool knob — not an aftermarket equivalent — and is used on both washer and dryer control panels depending on model. Replaces W10453947, 2304653, AP5607287, AWP50246, EAP3632979, PD00008425, PS3632979. Classic symptom: knob spins freely on the shaft without turning the dial, or won't stay in the selected cycle position. Common Problems This Part Fixes Control knob spins freely on the shaft without engaging the dial underneath Knob is cracked, chipped, or has broken retaining tabs on the back Knob won't stay pointed at the selected cycle Indicator marking or pointer on the knob is faded, worn, or broken off Knob is missing entirely, making it difficult to select a cycle Knob feels loose or wobbly on the control shaft Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This control knob directly replaces the following OEM and cross-reference part numbers: W10453947, 2304653, AP5607287, AWP50246, EAP3632979, PD00008425, PS3632979 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This control knob is compatible with select washer and dryer models from the following brands: Whirlpool washers and dryers (including WTW4616FW1, NTW4700YQ0, and related models) Amana washers and dryers (select models) Admiral washers and dryers (select models) Inglis washers and dryers (select models) Roper washers and dryers (select models) Kenmore washers and dryers (select Whirlpool-built models) Crosley washers and dryers (select models) Maytag washers and dryers (select Whirlpool-built models) Note: This same knob is used across hundreds of washer and dryer model numbers on both appliance types. Always verify fit using your appliance's exact model number before ordering, since visually similar knobs with a different shaft profile are used on other platforms. Contact our support team with your model number if you're unsure. Key Features Genuine Whirlpool OEM control knob — factory-original fit, feel, and appearance Used on both washer and dryer control panels across the Whirlpool platform Resolves "knob spins freely," "cracked knob," and "missing cycle indicator" symptoms Matches original detent feel and cycle-position indicator Push-on friction fit — no tools required for installation Replaces W10453947, 2304653, AP5607287, AWP50246, EAP3632979, PD00008425, PS3632979 Compatible with Whirlpool, Amana, Admiral, Inglis, Roper, Kenmore, Crosley, and Maytag washers and dryers Genuine OEM part — factory-specified materials and markings Product Specifications Part Number WPW10453947 OEM Part Number WPW10453947 Part Type Washer / Dryer Control Knob Condition Genuine OEM Replacement Application Washer or Dryer Cycle-Selector Control Panel Mounting Push-on friction fit to control shaft Compatible Brands Whirlpool, Amana, Admiral, Inglis, Roper, Kenmore, Crosley, Maytag Installation Notes ℹ️ No Tools Required — Unplug Appliance First Disconnect power to the washer or dryer before beginning. Note the current cycle position of the old knob before removing it, so you can align the new one the same way. Grip the old knob firmly and pull straight outward, away from the console, to release it from the friction fit on the shaft. If it's cracked and difficult to grip, work a flat-blade screwdriver gently behind the knob's edge to help pry it free, taking care not to damage the console. Line up the new WPW10453947 knob's D-shaped (or splined) center opening with the flat side of the control shaft, and press straight in until it seats fully against the console. Restore power and test that the knob turns smoothly through each cycle position and the indicator lines up correctly. Frequently Asked Questions Is this knob for a washer or a dryer? Both — this is a shared control knob design used on select Whirlpool-platform washers and dryers, depending on the model. The knob itself is identical; what it controls (wash cycle vs. dry cycle) depends on which appliance and console it's installed in. Confirm your appliance's model number before ordering to make sure this is the correct knob for your specific control panel. My knob spins freely and doesn't change the cycle — is this the fix? Yes, in most cases. This happens when the knob's internal shaft-grip (the D-shaped or splined opening that mates with the control shaft) wears out or cracks, so the knob spins independently of the shaft underneath it. Replacing the knob restores a snug grip on the shaft so turning it actually moves the selector. Do I need any tools to install this? No — it's a simple push-on friction fit. Pull the old knob straight off the shaft (a flat-blade screwdriver can help pry a stuck or cracked one loose) and press the new one on, matching the shaft's flat side to the knob's opening. No screws or fasteners are involved. Is this a genuine Whirlpool part or an aftermarket equivalent? This is the genuine, factory-original Whirlpool knob — not an aftermarket equivalent. It matches the original shaft profile, detent feel, and cycle-indicator markings, so there's no mismatch in fit or appearance versus the original equipment. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine Whirlpool OEM Part ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

5304524452 Washer Genuine OEM Drain Pump Assembly The 5304524452 is a genuine Frigidaire OEM drain pump assembly for Frigidaire stacked laundry center (washer/dryer combo) units, and also fits select Crosley, Electrolux, Gibson, Kelvinator, Westinghouse, and Kenmore models. This pump removes wash water from the tub at the end of each cycle, draining it out before the washer refills with fresh water for rinses. Common causes of a failing pump include normal wear and tear over time, an obstructed drain line, or issues with the pump housing or impeller. Symptoms of a bad pump assembly include incomplete draining of water at the end of cycles, water pooling in the tub, or the washer failing to advance through its cycle because it can't clear the water. It directly replaces 4246239, 4839543, 4959972, 5304500535, 5304515673, A03077601, AP5962219, AP6333076, AFR19009, AP6989734, BPX401-13J, EAP11703882, EAP12365991, EAP16218540, PD00063454, PS16218540. Quick Answer The 5304524452 Washer Genuine OEM Drain Pump Assembly fixes Frigidaire, Crosley, Electrolux, Gibson, Kelvinator, Westinghouse, and Kenmore stacked laundry center units where the washer won't drain, water pools in the tub, or the cycle won't advance past the drain step. Replaces 4246239, 4839543, 4959972, 5304500535, 5304515673, A03077601, AP5962219, AP6333076, AFR19009, AP6989734, BPX401-13J, EAP11703882, EAP12365991, EAP16218540, PD00063454, PS16218540. Several sources note that some replacement drain pumps look similar to this one but aren't the same part — check your original pump's model number or your washing machine's model number carefully before ordering. Common Problems This Part Fixes Washer not draining at the end of a cycle Water pooling or standing in the tub after a completed cycle Washer failing to advance past the drain step Incomplete draining leaving damp or soaked clothes Pump making unusual noise from a damaged impeller Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer drain pump assembly directly replaces the following OEM and cross-reference part numbers: 5304524452, 4246239, 4839543, 4959972, 5304500535, 5304515673, A03077601, AP5962219, AP6333076, AFR19009, AP6989734, BPX401-13J, EAP11703882, EAP12365991, EAP16218540, PD00063454, PS16218540 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drain pump assembly is compatible with select Frigidaire stacked laundry center units, and also fits select Crosley, Electrolux, Gibson, Kelvinator, Westinghouse, and Kenmore combo units built on the same platform, including model numbers such as CFLE3900UW0, CFLE3900UW1, CFLE3900UW3, FFLE3900UW0, FFLE3900UW1, FFLE3900UW2, FFLE3900UW3, FFLE3911QW0, FFLE3911QW1, FFLE39C1QW0, FFLE4033QT0, FFLE4033QW0, FFLE40C3QT0, FFLE40C3QW0, FFLG3900UW0, FFLG3900UW1, FFLG3900UW2, FFLG3900UW5, FFLG3911QW0, FFLG3911QW1, FFLG3911QW2, FFLG4033QT0, FFLG4033QT1, FFLG4033QW0, FFLG4033QW1, SFLG3911RW0, SFLG3911RW1, SFLG4033RT0, SFLG4033RT1, SFLG4033RW0, SFLG4033RW1, and Kenmore 417.61712510, 417.61712511, 417.61722510, 417.61723510, 417.61732810, 417.61733810, 417.71712510, 417.71712511, 417.71722510, 417.71722511, 417.71723510, 417.71723511, 417.71732810, and 417.71733810. Note — similar-looking but different pumps exist: Some replacement drain pumps are visually similar to this one but aren't compatible. Check your original pump's model number or your washing machine's model number carefully before ordering. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine Frigidaire OEM part — factory-specified pump housing and impeller design Drains wash water from the tub at the end of each cycle Resolves "won't drain," "water pooling," and "won't advance past drain step" symptoms Direct drop-in replacement matching the original mounting and hose connections Replaces 4246239, 4839543, 4959972, 5304500535, 5304515673, A03077601, AP5962219, AP6333076, AFR19009, AP6989734, BPX401-13J, EAP11703882, EAP12365991, EAP16218540, PD00063454, PS16218540 Compatible with Frigidaire, Crosley, Electrolux, Gibson, Kelvinator, Westinghouse, and Kenmore laundry center units Genuine OEM replacement — guaranteed fit, materials, and performance Simple DIY repair with basic tools Product Specifications Part Number 5304524452 Part Type Washer Drain Pump Assembly Condition Genuine OEM Brand Frigidaire Application Stacked Washer/Dryer Laundry Centers Function Drains wash water from the tub at the end of each cycle Repair Difficulty Easy Quantity 1 drain pump assembly Compatible Brands Frigidaire, Crosley, Electrolux, Gibson, Kelvinator, Westinghouse, Kenmore Installation Notes ⚠️ Unplug The Laundry Center And Shut Off Water Supply Before Starting Disconnect power to the laundry center unit and shut off the water supply before beginning. Wear work gloves and have towels ready for any residual water. Access the pump, typically located at the bottom front or rear of the washer section depending on your model. Remove the clamp attaching the hose to the old pump, then remove the hose. Remove the three screws holding the pump to the washer. Take out the old pump. Install the new 5304524452 in the same position and secure it with the three mounting screws. Reattach the hose to the new pump and secure the clamp. Restore the water supply and power, then run a test cycle to confirm the washer drains completely with no leaks. Tools needed: pliers, screwdriver, work gloves. Frequently Asked Questions My washer isn't draining. Is this the part I need? Yes, this is the most direct symptom of a failed drain pump. Since this pump is responsible for removing wash water from the tub at the end of each cycle, a worn impeller or internal failure can leave water standing in the tub and prevent the washer from advancing to the next stage of the cycle. Is this a difficult repair? No, one customer described it as an easy removal and installation: remove the clamp attaching the hose to the pump, remove the hose, remove the three screws holding the pump to the washer, then reverse the process with the new pump. How do I make sure I'm ordering the correct pump, since some look similar? Check the model number printed on your original pump, or your washing machine's full model number, before ordering. Multiple sources note that some replacement drain pumps look visually similar to this one but aren't actually compatible, so matching your specific part or model number is the reliable way to confirm fit. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Frigidaire to factory specifications — guaranteed fit, materials, and performance. It matches the original pump housing, impeller, and connection type of the drain pump assembly originally installed in your washer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

Genuine Frigidaire OEM Frigidaire 5304533220 Washer Water Fill Hose Assembly Genuine OEM internal valve-to-tub fill hose for select Frigidaire-built laundry centers and washer/dryer combination units. Product Overview The Frigidaire 5304533220 Washer Water Fill Hose Assembly is a Genuine OEM internal fill hose used to route incoming water from the washer water inlet valve to the wash tub on compatible laundry-center models. This is the valve-to-tub hose inside the appliance. It is not the external hot/cold household water-supply hose that connects the appliance to the wall faucets. Quick Answer 5304533220 is the Genuine Frigidaire OEM valve-to-tub washer fill hose. It replaces earlier Frigidaire numbers 5304508358 and 809191901 and is used on select Frigidaire, Kenmore, Crosley, and other Electrolux-manufactured laundry centers. Common Problems This Part May Fix Water leaking inside the washer cabinet during fill Cracked, split, hardened, or deteriorated fill hose Leak between the inlet-valve outlet and wash tub Loose or damaged internal water-fill connection Water dripping from the valve-to-tub hose during operation Replaces and Cross-References 5304533220, 5304508358, 809191901, AFR20016, AP7194866, EAP11775692, PD00076846, PS16745853 Cross-reference numbers are provided for identification. Always verify the full appliance model number before ordering. Compatibility Confirmed applications include select Frigidaire-built laundry centers and washer/dryer combinations such as: FLCE7523AW0 FLCE7523AW1 FLCE7522AW1 FLCE7522AW4 FFLE3900UW0 FFLE3900UW1 FFLG3900UW0 FFLE3911QW1 CFLE3900UW0 41761712511 41761732810 41771732810 Important: This is only a partial compatibility list. Confirm the complete model number from the appliance rating label before purchase. Key Features Genuine Frigidaire OEM replacement part Internal valve-to-tub fill hose Routes fill water from the inlet valve to the washer tub Direct replacement for 5304508358 and 809191901 Factory-style fit for compatible laundry centers Used on select Frigidaire, Kenmore, and related Electrolux-built models Product Specifications Manufacturer Part Number 5304533220 Brand Frigidaire Part Type Washer Internal Water Fill Hose Hose Location Water Inlet Valve to Wash Tub OEM Status Genuine OEM Appliance Type Laundry Center / Washer-Dryer Combo Condition New External Supply Hose? No — this is an internal appliance hose Installation Notes Disconnect electrical power to the appliance before service. Shut off both household water-supply valves. Access the washer inlet-valve and tub-fill connection according to the model-specific service procedure. Place towels or a shallow pan below the hose connections to catch residual water. Release the clamps and remove the old hose without damaging the valve outlet or tub fitting. Install the new hose fully onto both fittings and reinstall the clamps in their original positions. Restore water and inspect carefully for leaks before returning the appliance to service. Diagnostic tip: If water is leaking during fill, inspect the hose, clamps, inlet valve, and tub connection before replacing parts. A leak from the external household supply hose requires a different part. Frequently Asked Questions Is 5304533220 a Genuine OEM part? Yes. It is a Genuine Frigidaire OEM fill hose. Does 5304533220 replace 5304508358? Yes. 5304533220 supersedes 5304508358 and 809191901. Is this the hose that connects the washer to the wall faucet? No. This is an internal valve-to-tub fill hose located inside the laundry center. Can this part correct a washer leak? Yes, if the leak is caused by a cracked or damaged valve-to-tub fill hose or its connection. Inspect all nearby fittings and clamps before ordering. Shop With Confidence Verify your complete laundry-center model number before ordering. This listing is for the Genuine Frigidaire OEM internal valve-to-tub fill hose. Genuine Frigidaire OEMValve-to-Tub Fill HoseCompatibility SupportFast U.S. Shipping

Read more less