Appliance Parts

XPARTCO 6602-001655 Dryer Drum Belt The XPARTCO 6602-001655 is an aftermarket replacement dryer drum belt compatible with select Samsung and Kenmore dryers. The drum belt wraps around the outside of the dryer drum, loops around the motor pulley and idler pulley, and drives the drum to rotate during every drying cycle. Without a functioning belt, the drum cannot spin and clothes will not tumble or dry. Made from premium neoprene rubber reinforced with polyester cords, this 5-rib belt measures 92 inches long x 5/16 inch wide and is built to resist cracking, stretching, and wear under the high heat and repeated tension cycles of daily dryer use. It is a direct drop-in replacement for OEM part numbers 6602-001655 and 6602-001314, and installs in 30–45 minutes with basic hand tools. Quick Answer The XPARTCO 6602-001655 Dryer Drum Belt fixes dryers where the drum is not spinning, clothes are not tumbling, or a thumping/squealing noise is coming from the dryer during operation. It drives the drum via the motor and idler pulleys. Compatible with select Samsung and Kenmore dryers. Measures 92" L x 5/16" W with 5 ribs and 4 grooves. Common Problems This Part Fixes Dryer drum not spinning — motor runs but drum stays still Clothes not tumbling during the drying cycle Thumping, squealing, or slapping noise during operation Dryer runs but produces no heat because drum is stationary Visible broken or frayed belt pieces found inside the dryer cabinet Dryer shuts off shortly after starting due to drum not rotating Replaces Part Numbers This drum belt directly replaces the following OEM and cross-reference part numbers: 6602-001655, 6602-001314, 5PH2337, LB1655, ASM874658, PD00002012, EAP2407938, AP4373659, PS4133825. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drum belt is compatible with select dryers from the following brands: Samsung dryers (gas and electric) Kenmore / Sears dryers (select models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Drives the dryer drum via the motor pulley and idler pulley for smooth, consistent tumbling every cycle 92" length x 5/16" width — 5-rib, 4-groove design for a secure, slip-free grip on the pulleys Made from premium neoprene rubber with polyester cord reinforcement — resists cracking, stretching, and heat damage Direct replacement for OEM part numbers 6602-001655 and 6602-001314 — no modification required Aftermarket replacement built to OEM-equivalent quality standards DIY-friendly repair — installs in 30–45 minutes with basic hand tools Often replaced together with the idler pulley (DC93-00634A) and drum rollers (DC97-16782A) for a complete drum drive repair Product Specifications Part Number 6602-001655 Part Type Dryer Drum Drive Belt Condition Aftermarket Replacement Application Gas and Electric Dryers Length 92 inches Width 5/16 inch Height 1/8 inch Ribs 5 ribs, 4 grooves Material Neoprene rubber with polyester cord reinforcement Color Black Compatible Brands Samsung, Kenmore Often Replaced With DC93-00634A Idler Pulley, DC97-16782A Drum Rollers Installation Notes ⚠️ Safety First — Unplug Dryer Before Starting Unplug the dryer from the power source (and shut off the gas supply for gas dryers) before beginning any repair. To access the drum belt, remove the top panel and front panel of the dryer. Lift the drum out of the cabinet, remove the old belt, and loop the new 6602-001655 belt around the drum with the ribbed side facing inward. Route the belt slack around the idler pulley and motor pulley — consult your dryer's service manual or a model-specific video for the correct belt path around the pulleys. Reassemble the front panel, top panel, and restore power before running a test cycle. Tip: While the drum is out, this is an ideal time to also inspect and replace the idler pulley and drum support rollers if worn. Tools needed: Phillips screwdriver, putty knife or flat pry tool. Frequently Asked Questions Will the 6602-001655 fit my Samsung or Kenmore dryer? This belt is compatible with select Samsung and Kenmore dryers. Use the model search above to verify your model number, or contact our support team before ordering. What does the dryer drum belt do? The drum belt wraps around the outside of the dryer drum and connects to the motor pulley and idler pulley. As the motor spins, it drives the belt which causes the drum to rotate, tumbling your clothes through the heated air to dry them. A broken or worn belt means the drum cannot spin. How do I know if my drum belt is broken? The most obvious sign is that the dryer motor runs and you can hear it humming, but the drum does not spin. You may also hear a thumping or slapping sound if the belt is slipping or partially broken. Opening the dryer cabinet and visually inspecting the belt will confirm if it is broken, frayed, or stretched. Should I replace the idler pulley and drum rollers at the same time? Yes — since you need to disassemble the dryer to replace the belt anyway, it is highly recommended to also inspect and replace the idler pulley (DC93-00634A) and drum support rollers (DC97-16782A) at the same time. These parts wear at a similar rate and replacing all three together prevents having to disassemble the dryer again in the near future. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is made from premium neoprene rubber with polyester cord reinforcement to match the dimensions and performance of the original belt. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO DC93-00634A Dryer Idler Pulley  The XPARTCO DC93-00634A is an aftermarket replacement idler pulley assembly compatible with a wide range of Samsung dryers. The idler pulley rides against the drive belt and keeps it under proper tension as it wraps around the drum and motor pulley. Over time, the pulley wheel can wear, crack, or seize on its shaft, or the spring-loaded tensioner arm can bend or break, causing the belt to lose tension. When this part fails, the dryer commonly won't spin at all even though the motor runs, makes a loud noise from the drive area, or the belt goes slack and starts slipping. It directly replaces DC93-00634A, DC97-07509B, DC61-01230B, DC96-00882B, DC96-00882C, 4455850, AP6038887, ASM34631, EAP11771601, PD00032419, PS11771601. Installs in 30 minutes to 2 hours depending on how much disassembly your model requires. Quick Answer The XPARTCO DC93-00634A Dryer Idler Pulley fixes Samsung dryers that won't spin the drum even though the motor runs, make a loud noise from the drive belt area, or have a loose/slipping belt. Replaces DC93-00634A, DC97-07509B, DC61-01230B, DC96-00882B, DC96-00882C, 4455850, AP6038887, ASM34631, EAP11771601, PD00032419, PS11771601. Classic symptom: motor hums and runs, but the drum doesn't turn — "no spin, no start." Common Problems This Part Fixes Dryer motor runs but the drum doesn't spin ("no spin, no start") Loud noise or rattling coming from the drive belt/motor area Drive belt slipping, loose, or off-track Visible cracks, wear, or seizing on the pulley wheel Bent or broken tensioner arm/spring Squeaking noise from the pulley as it rotates Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This idler pulley directly replaces the following OEM and cross-reference part numbers: DC93-00634A, DC97-07509B, DC61-01230B, DC96-00882B, DC96-00882C, 4455850, AP6038887, ASM34631, EAP11771601, PD00032419, PS11771601 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This idler pulley is compatible with a wide range of Samsung dryers, including: Samsung DV337AEG/XAA-0000 Samsung DV45H7000EW/A2-0000 Samsung DV45K6200EZ/A3 Samsung DV203AEW/XAA-0000, DV203AGS, and related models Note: This idler pulley is specific to the Samsung drive belt platform and does not fit LG, Whirlpool, GE, or other brands, which use different pulley designs. Always verify your appliance model number before ordering. Contact our support team with your model number if you're unsure. Key Features Direct-fit replacement Samsung dryer idler pulley assembly Resolves "no spin, no start," "loud noise," and "loose/slipping belt" symptoms Maintains proper belt tension as the belt wraps around the drum and motor pulley Spring-loaded tensioner arm matches original design for correct belt tension Replaces DC93-00634A, DC97-07509B, DC61-01230B, DC96-00882B, DC96-00882C, 4455850, AP6038887, ASM34631, EAP11771601, PD00032419, PS11771601 Compatible with a wide range of Samsung dryer models Aftermarket replacement built to OEM-equivalent quality standards Exact-fit design — no modification needed for installation Product Specifications Part Number XPDC93-00634A OEM Part Number DC93-00634A Part Type Dryer Idler Pulley Assembly Condition Aftermarket Replacement Function Maintains drive belt tension Application Samsung Dryer Drive Belt System Compatible Brand Samsung Installation Notes ⚠️ Unplug Dryer Before Starting Disconnect power before beginning. Remove the front panel and/or top panel as needed to access the drum and drive belt (access point varies by model). Photograph the belt routing before removing anything. Relieve tension on the drive belt by pressing the idler pulley toward the motor, then slip the belt off the pulley and motor shaft. Remove the mounting screw or clip holding the idler pulley bracket in place and remove the old pulley assembly. Install the new DC93-00634A pulley in the same position and secure it. Route the new belt back around the drum and motor pulley, using the idler pulley to apply tension, matching your photos of the original routing. Reassemble any panels removed for access, restore power, and run a test cycle to confirm the drum spins smoothly and quietly. Tools needed: Phillips or nut driver, putty knife (for panel clips, if applicable). Frequently Asked Questions My dryer's motor runs but the drum won't spin — is this the part? This is the classic "no spin, no start" symptom of a failed idler pulley or a broken drive belt. If the pulley wheel is cracked, seized, or the tensioner arm is bent or broken, the belt loses tension and can no longer transfer power from the motor to the drum. Inspect the belt for damage as well, since a broken belt often accompanies a worn idler pulley. Do I need to replace the drive belt at the same time? Not necessarily, but it's worth inspecting closely while you have the drum accessible. If the idler pulley failed due to age or wear, the belt has often experienced similar stress and may be worn, glazed, or close to failing itself. Many technicians replace both together to avoid a repeat repair. Will this fit my LG or Whirlpool dryer? No — this idler pulley is specific to the Samsung drive belt platform. LG, Whirlpool, GE, and other brands use different idler pulley and belt tensioning designs that are not interchangeable with this part. Confirm your appliance model number before ordering. How long does this repair typically take? Most installers report 30 minutes to 2 hours depending on how much disassembly your specific model requires to access the belt and pulley. Front panel removal is usually the more time-consuming part; the pulley swap itself is quick once accessed. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

WP3392519 Genuine OEM Whirlpool Dryer Thermal Fuse The WP3392519 is a genuine Whirlpool OEM thermal fuse mounted on the blower housing next to the blower fan. This fuse is a one-time safety device: as long as the dryer stays within its normal operating temperature, it does nothing at all, but the instant internal temperatures climb high enough — almost always from restricted airflow — the fuse permanently opens the circuit and cuts power to the dryer. That's why a blown thermal fuse produces such a specific symptom: the dryer won't start at all, with no lights, no tumble, and no response, even though the outlet has power. This fuse opens at approximately 196°F (91°C) and terminates in two 3/16" wire terminals for a direct plug-in fit. Unlike a resettable thermostat, this thermal fuse cannot be reset once it blows — it must be replaced. A blown thermal fuse is almost always a symptom rather than a random failure: restricted exhaust venting is the leading cause, since trapped heat is exactly what the fuse is designed to react to. A shorted heating element or a failed regulating thermostat can also cause the dryer to run hot enough to blow the fuse. It directly replaces 3392519, WP3392519VP, AP6008325, 3388651, 694511, ET401, PS11741460, EAP11741460, AH11741460, EA11741460, PD00002311, G4AP0500, and 80005. Quick Answer The WP3392519 Genuine OEM Whirlpool Dryer Thermal Fuse fixes Whirlpool, Maytag, Kenmore, KitchenAid, Roper, Jenn-Air, and Amana dryers that won't start at all — no lights, no tumble, no response to any button. Opens at approximately 196°F (91°C). Two 3/16" wire terminals. Replaces 3392519, WP3392519VP, AP6008325, 3388651, 694511, ET401, PS11741460, EAP11741460, AH11741460, EA11741460, PD00002311, G4AP0500, 80005. Always inspect and clean the dryer venting when replacing this fuse — a blown fuse is a symptom of restricted airflow, and installing a new fuse without fixing the vent will likely blow it again. Common Problems This Part Fixes Dryer won't start at all — no lights, no tumble, no response to any button Dryer that stopped working suddenly, especially after running unusually hot Dryer runs a short time then shuts off completely and won't restart Repeated blown fuses on a dryer with a known venting or airflow restriction Clothes coming out extremely hot right before the dryer stopped working Dryer that recently smelled like burning or overheating before failing Continuity test shows an open circuit across the old fuse Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer thermal fuse directly replaces the following OEM and cross-reference part numbers: 3392519, WP3392519, 3388651, WE4X857, G4AP0500, 6L4101, 6L4101091C, ET401, 3388651, 694511, 80005, AWP47582, PD00002311, EAP11741460, AP6008325, PS11741460 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This thermal fuse is compatible with select Whirlpool-built dryers across the Whirlpool family of brands, including: Whirlpool electric and gas dryers — WED, WGD series Maytag electric and gas dryers — MEDC, MGDC series (select Whirlpool-built models) Kenmore dryers (select Whirlpool-built models) KitchenAid, Jenn-Air, and Amana dryers (select models) Roper, Estate, Inglis, and Crosley dryers (select models) Verified model numbers include: MEDC465HW0, MGDC465HW0, WED4850HW0, WED4950HW0, WED49STBW1, WET4024HW0, WET4124HW0, WGD4850HW0, WGD4950HW0, YMEDC465HW0, YWED4850HW0, and YWET4024HW0. Note: This fuse also fits select commercial and stacked washer/dryer combination units on the Whirlpool platform. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine Whirlpool OEM part — factory-specified opening temperature and terminal configuration One-time safety device that cuts power if the dryer overheats Opens at approximately 196°F (91°C) Resolves "won't start at all," "stopped working suddenly," and "clothes came out extremely hot before it died" symptoms caused by a blown fuse Two 3/16" wire terminal connectors for a direct plug-in electrical fit Mounts to the blower housing next to the blower fan Replaces 3392519, WP3392519VP, AP6008325, 3388651, 694511, ET401, PS11741460, EAP11741460, AH11741460, EA11741460, PD00002311, G4AP0500, and 80005 Compatible with Whirlpool, Maytag, Kenmore, KitchenAid, Roper, Jenn-Air, and Amana dryers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number WP3392519 Part Type Dryer Thermal Fuse (Thermal Cut-Off) Condition Genuine OEM Brand Whirlpool Opening Temperature Approx. 196°F (91°C) Location Blower housing, next to the blower fan Terminals 2 (3/16" wire terminals) Resettable No — one-time use, must be replaced once blown Dimensions Approx. 2" x 1/2" Repair Difficulty Medium — basic disassembly required Quantity 1 thermal fuse Compatible Brands Whirlpool, Maytag, Kenmore, KitchenAid, Roper, Jenn-Air, Amana, Estate, Inglis, Crosley Installation Notes ⚠️ Unplug Dryer Before Starting — Inspect And Clean The Venting Before Reassembling Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access is typically through the rear panel: remove the screws securing the panel to reach the blower housing where the fuse is mounted. Photograph the wiring before disconnecting the wire terminals from the old fuse. Remove the mounting screw holding the fuse in place and pull it free, disconnecting both wire terminals. Before installing the new fuse, test it for continuity with a multimeter to confirm it's good out of the box, and test the old one to confirm it's actually blown (no continuity) rather than assuming. This is the most important step: fully inspect and clean the dryer's exhaust vent, from the lint trap housing all the way to the exterior vent hood, checking for lint buildup, crushed sections, or excessive length. A blown thermal fuse is a symptom of restricted airflow, and skipping this step means the new fuse is likely to blow again. Install the new WP3392519 in the same mounting position, reconnect both wire terminals, and secure the mounting screw. Reinstall the rear panel, restore power, and run a test cycle to confirm normal heating and shutoff behavior. Tools needed: Phillips or nut driver (model-dependent), multimeter, vent brush or vacuum attachment for cleaning ductwork, work gloves. Frequently Asked Questions My dryer has no power at all and the lights won't turn on. Is this the thermal fuse? It's a strong possibility. When this thermal fuse blows, it cuts power broadly enough that the console lights and control panel can go completely dark, not just the heating function — that's a normal result of how this fuse is wired into the circuit. Before replacing it, confirm the outlet has power and the breaker hasn't tripped, then check the fuse for continuity with a multimeter. If it shows no continuity, this fuse is the correct fix, though it's also worth checking the exhaust ducting since that's the most common underlying cause. I replaced the fuse and it blew again. What's going on? This is a strong sign that the underlying cause — almost always restricted airflow — was never addressed. Thermal fuses don't fail from age; they blow because the dryer overheated. If a new fuse keeps blowing, thoroughly inspect and clean the entire exhaust path from the lint trap housing to the outside vent hood, checking for lint buildup, crushed or kinked ductwork, or a vent run that's too long. If airflow checks out and the fuse still blows, have the heating element and cycling thermostat checked as well, since a component stuck in the "on" position can also drive excess heat. Can I just reset the thermal fuse instead of replacing it? No. Unlike a cycling thermostat, this thermal fuse is a one-time safety device — once it blows, its internal circuit is permanently broken and it cannot be reset or repaired. Replacement is the only option. My clothes came out extremely hot right before the dryer died. Is that related? Yes, this is a classic warning sign. Clothes coming out unusually hot indicates the dryer was already running hotter than normal, which is exactly the condition that leads to a blown thermal fuse. If you noticed this before the dryer stopped working, it strongly points to a ventilation or airflow problem that should be fully addressed before running the dryer again. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original opening temperature, terminal configuration, and mounting position of the thermal fuse originally installed in your dryer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO DC31-00187A Washer Drain Pump Motor The XPARTCO DC31-00187A is an aftermarket replacement washer drain pump motor compatible with select Samsung front-load and top-load washers in the WA4, WA5, WF2, WF3, WF4, and WF5 series, as well as select Kenmore washers built on the Samsung platform. The drain pump motor drives the impeller that expels water from the washer tub during the drain phase of each wash cycle. When the motor fails, the washer will not drain, will leave standing water in the tub, stop mid-cycle, or display error codes 5C, SE, SC, 5E, or SUDS. This motor-only assembly includes the pump motor, impeller, and replacement O-ring. Rated 120V, 60Hz, 80W, 1.1A (CL.F), with a 30-minute on / 30-minute off duty cycle. Dimensions: 4-1/4"L x 3"W x 4-1/4"H in gray/white/black plastic, metal, and rubber housing. The DC31-00187A is the motor component that installs into the existing pump housing on compatible Samsung washers — the pump housing (DC97-20621C assembly) is reused from the old pump, making this a motor-only swap rather than a complete pump replacement. It directly replaces DC31-00187D, DC31-00178A, DC31-00178D, PX3516-01, 03DC3100187A, 4958525, AP6977256, EAP9605762, PD00056512, PS9605762, and PS1274262. Installs in 20–30 minutes with basic hand tools. Quick Answer The XPARTCO DC31-00187A Washer Drain Pump Motor fixes Samsung front-load and top-load washers displaying error codes 5C, SE, SC, 5E, or SUDS, not draining, leaving standing water, or making loud noise during the drain cycle. Motor-only assembly — includes motor, impeller, and O-ring; installs into existing pump housing. 120V/60Hz/80W/1.1A/CL.F. 30 min on/30 min off. 4-1/4"L x 3"W x 4-1/4"H. Replaces DC31-00187D, DC31-00178A, DC31-00178D, PX3516-01, 4958525, AP6977256, PS9605762. Compatible with Samsung WA4/WA5/WF2/WF3/WF4/WF5 series. Common Problems This Part Fixes Washer not draining — standing water remaining in the tub after a cycle Error codes 5C, SE, SC, 5E, or SUDS displayed — drain fault detected Washer stopping mid-cycle due to a drain fault Loud humming during the drain phase — motor energized but impeller not turning Grinding or rattling during drain — damaged impeller or worn motor bearings Clothes excessively wet after a cycle — pump not fully removing water before spin Water draining very slowly — motor weakening below rated performance Replaces Part Numbers This drain pump motor directly replaces the following OEM and cross-reference part numbers: DC31-00187A, DC31-00178A, DC31-00178D, 03DC3100187A, ASM654116, EAP9605762, 4958525, AP6977256, PD00056512, PS12742622, PX3516-01. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drain pump motor is compatible with select Samsung front-load and top-load washers from the following series: Samsung top-load washers — WA4 series (WA40J3000AW, WA44A3205AW, WA45H7000AW, WA45M7050AW, WA45N3050AW, WA45T3200AW, WA45R6100AC and related models) Samsung top-load washers — WA5 series (WA50F9A6DSW, WA50M7450AW, WA50R5200AW, WA50R5400AV and related models) Samsung front-load washers — WF2 series (select models) Samsung front-load washers — WF3 series (select models) Samsung front-load washers — WF4 series (WF42H5000AW, WF42H5200AW, WF45M5500AW, WF45N5300AW, WF45R6100AC, WF45T6000AW, WF45A6400AV, WF45B6300AP and related models) Samsung front-load washers — WF5 series (select models) Kenmore / Sears washers (select Samsung-built models) Note: The DC31-00187A is the pump motor only — it installs into the existing pump housing (DC97-20621C assembly) which is retained from the old pump. The housing is not replaced. Check and clean the drain filter before replacing the pump motor — a clogged filter is a common cause of drain errors that doesn't require motor replacement. Key Features Pump motor only — includes motor, impeller, and O-ring; installs into the existing DC97-20621C pump housing retained from the old pump Drives the pump impeller to expel water from the washer tub during the drain cycle Resolves Samsung error codes 5C, SE, SC, 5E, and SUDS caused by drain pump motor failure Rated 120V, 60Hz, 80W, 1.1A (CL.F) — correct specifications for compatible Samsung washers Duty cycle: 30 minutes on / 30 minutes off Dimensions: 4-1/4"L x 3"W x 4-1/4"H Replaces DC31-00187D, DC31-00178A, DC31-00178D, PX3516-01, 4958525, AP6977256, PS9605762, and PS1274262 Compatible with Samsung WA4, WA5, WF2, WF3, WF4, WF5 series and Kenmore Samsung-built washers Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 20–30 minutes with basic hand tools Product Specifications Part Number XPDC31-00187A Also Covers DC31-00187D, DC31-00178A, DC31-00178D (variants) Part Type Washer Drain Pump Motor (Motor Only — reuses existing housing) Condition Aftermarket Replacement Application Samsung Front-Load and Top-Load Washers (WA4/WA5/WF2/WF3/WF4/WF5) Voltage 120V AC Frequency 60 Hz Wattage 80W Amperage 1.1A Duty Class CL.F Duty Cycle 30 minutes on / 30 minutes off Dimensions 4-1/4"L x 3"W x 4-1/4"H Color Gray / White / Black Material Plastic / Metal / Rubber Includes Pump motor, impeller, O-ring Error Codes Resolved 5C, SE, SC, 5E, SUDS Compatible Brands Samsung, Kenmore (Samsung-built) Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting — Wear Gloves Disconnect power and turn off the water supply before beginning. Wear work gloves — there are sharp edges inside the washer cabinet. For front-load models: remove the lower front access panel to expose the pump housing and filter. Drain residual water via the filter drain hose (have a shallow pan ready). Disconnect the wire harness from the motor. On most Samsung front-load models, the motor assembly twists out of the pump housing by rotating counter-clockwise — do not force it. Remove the old motor, note the O-ring position, and install the new O-ring from this kit onto the new DC31-00187A motor. Insert the new motor into the housing and twist clockwise to lock. Reconnect the wire harness. Reinstall the lower panel, restore power and water, and run a drain/spin cycle to confirm drainage. For top-load models: access through the lower front panel or by tilting the washer on its side depending on model. Tools needed: Phillips screwdriver, pliers, shallow pan, towels, work gloves. Frequently Asked Questions What is the difference between DC31-00187A and DC97-20621C? The DC31-00187A is the drain pump motor — the electrical component that drives the impeller. The DC97-20621C is the complete drain pump assembly, which includes the motor plus the outer pump housing, hose connection ports, and mounting hardware. When you order the DC31-00187A, you replace only the motor and reuse the existing DC97-20621C pump housing. When you order the DC97-20621C, you replace the entire assembly including the housing. Both resolve the same drain fault — the DC31-00187A is the more targeted repair when the housing is in good condition. What error codes indicate a drain pump motor failure? Error codes 5C, SE, SC, 5E, and SUDS on compatible Samsung washers all indicate a drain fault — the washer was unable to drain within the expected time. Before replacing the motor, clean the drain filter/coin trap at the lower front panel. A clogged filter is one of the most common causes of these error codes and does not require motor replacement. If the filter is clear and the codes persist, or if the pump is making loud noise or is completely silent during the drain phase, the motor needs replacement. What is the difference between DC31-00187A and DC31-00178A? These are cross-references for the same or very similar Samsung drain pump motor used across different Samsung washer generations. The DC31-00178A was used on earlier Samsung models and the DC31-00187A is the current version. Both are commonly listed as interchangeable replacements for each other in Samsung washer drain pump repair. The DC31-00187D and DC31-00178D are also variants of the same motor from different production runs. Should I clean the filter before replacing the pump motor? Yes — always check and clean the drain filter first. On Samsung front-load washers, the filter is accessible behind the lower front kick panel, typically on the right side — remove the cap slowly and drain water into a shallow pan first. Lint, coins, debris, and hair are very common causes of Samsung drain error codes that are completely resolved by cleaning the filter without any parts replacement. If the filter is clear and the error codes persist, the pump motor is the next component to replace. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured to match the electrical specifications and performance of the original DC31-00187A drain pump motor. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 6501KW2002B Washer Rotor Position Sensor – Compatible with LG and Kenmore Washers Product Description Maintain smooth spin cycles and precise motor control with the XPARTCO 6501KW2002B Washer Rotor Position Sensor. This Sensor Assembly, also known as a hall sensor is a replacement Part and is a vital component in Specific LG, Kenmore washer Models. This part monitors the direction and speed of the spinning rotor. It then communicates this information to the electronic control board. By doing so, it aids in the precise operation of your washer. If your washer pumps but fails to spin or agitate, it may be indicative of a damaged sensor assembly. Replaces Part Numbers 6501KW2002B, 6501KW2002A, AP7015078, PD00073205, EAP16556422, 4962510, PS16556422, EAP16556422. Compatibility This replacement rotor position sensor fits select LG and Kenmore front-load washers. Example compatible models include (but are not limited to): LG WM2487HRM, LG WM0642HW, and Kenmore 796.40272900. Always verify your washer’s model number before ordering. Contact our support team if you’re unsure. Key Features Aftermarket Replacement – Designed to match OEM performance and precision Accurate Rotor Feedback – Helps regulate motor speed and direction for smooth washing Cost-Effective Fix – Delivers OEM-level performance at a fraction of the price Plug-and-Play Installation – No wiring modification required Fixes Common Issues – Resolves LE, UE, SE, and spin cycle errors Product Specification Part Number: 6501KW2002B Component Type: Washer Rotor Position Sensor (Hall Sensor) Material: Durable printed circuit board with reinforced plastic housing Mounting: Direct-fit installation on stator assembly Operating Conditions: Rated for high-humidity, high-vibration washer environments Compliance: Built to OEM-equivalent quality standards (not OEM) Installation Notes Tools Needed: 10 mm socket wrench, Phillips screwdriver ⚠️ Safety First: Always unplug the washer before performing repairs to prevent electrical shock. Steps: Disconnect power and remove the rear access panel. Unscrew the rotor bolt and carefully remove the rotor assembly. Locate and unplug the old sensor from the stator. Install the new XPARTCO 6501KW2002B sensor, aligning mounting tabs. Reconnect the wiring harness, reinstall the rotor, and secure the panel. Restore power and run a spin test to verify correct operation. ⏱️ Time Required: 20–25 minutes Shop With Confidence Trusted Appliance Parts Supplier 30-Day Return Policy Restore precise washer performance — Add to Cart Now for a reliable, budget-friendly repair!

Read more less

341241 Dryer Genuine OEM Drum Belt The 341241 is a Genuine OEM dryer drum belt compatible with a wide range of Whirlpool-family dryers including Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Admiral, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, Norge, Modern Maid, Hardwick, Caloric, and Ikea. The drum belt wraps around the outside of the dryer drum, loops around the motor pulley and idler pulley, and drives the drum to rotate during every drying cycle. Without a functioning belt, the drum cannot spin and clothes will not tumble or dry. Made from high-strength rubber with reinforced ribs, this belt measures 92-1/4 inches long x 1/4 inch wide and features 4 ribs and 3 grooves. It is flat on one side and ribbed on the other, and is built to resist cracking, stretching, and wear under the high heat and repeated tension cycles of daily dryer use. It also replaces some 5-rib, 4-groove belts. Installs in 30–45 minutes with basic hand tools. Quick Answer The 341241 Dryer Genuine OEM Drum Belt fixes dryers where the drum is not spinning, clothes are not tumbling, or a thumping/squealing noise is coming from the dryer. Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Admiral, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, and more. Measures 92-1/4" L x 1/4" W with 4 ribs and 3 grooves. Common Problems This Part Fixes Dryer drum not spinning — motor runs but drum stays still Clothes not tumbling during the drying cycle Thumping, squealing, or slapping noise during operation Dryer runs but produces no heat because drum is stationary Burning rubber smell coming from the dryer Visible broken or frayed belt pieces found inside the dryer cabinet Clothes taking too long to dry due to drum not rotating at correct speed Replaces Part Numbers This drum belt directly replaces the following OEM and cross-reference part numbers: 341241, 14210003, 2008, 26000341241, 26000349533, 31001026, 31531589, 3389628, 3392665, 3394651, 3399844, 341241VP, 345473, 349533, 529597, 53-0186, 53-1080, 53-1086, 53-1528, 53-1589, 53-2671, 53-2910, 660996, 660997, 661561, 693306, 694088, 694416, 694868, 695055, 697388, 8066065, 8206, 8210, 920H4, 920H5, 99906951, 99989673, 99989674, FSP341241, LB276, LB279, P46-037, P46-149, W10127457, W10131364, AH346995, AP32, EA346995, ER341241, AWP39161, PD00002263, EAP346995, AP2946843, PS346995, TJ341241. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drum belt is compatible with select dryers from the following brands: Whirlpool dryers (gas and electric) Kenmore / Sears dryers (select models) Maytag dryers KitchenAid dryers Amana dryers Roper dryers Admiral dryers Jenn-Air dryers Estate dryers Magic Chef dryers Crosley dryers Inglis dryers Norge, Modern Maid, Hardwick, Caloric, and Ikea dryers Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Drives the dryer drum via the motor pulley and idler pulley for smooth, consistent tumbling every cycle 92-1/4" length x 1/4" width — 4-rib, 3-groove design; flat on one side, ribbed on the other Also replaces some 5-rib, 4-groove belts — wide cross-compatibility across Whirlpool-family models Made from high-strength rubber with reinforced ribs — resists cracking, stretching, and heat damage Direct replacement for OEM part numbers 341241 and 8066065 — no modification required Compatible with over a dozen major appliance brands built on the Whirlpool platform Genuine OEM part — factory-exact fit, materials, and dimensions DIY-friendly repair — installs in 30–45 minutes with basic hand tools Often replaced together with the idler pulley (691366) and drum rollers (349241T) for a complete drum drive repair Product Specifications Part Number 341241 Part Type Dryer Drum Drive Belt Condition Genuine OEM Application Gas and Electric Dryers Length 92-1/4 inches Width 1/4 inch Ribs 4 ribs, 3 grooves Profile Flat on one side, ribbed on the other Material High-strength rubber with reinforced ribs Color Black Compatible Brands Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Admiral, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, Norge, Modern Maid, Hardwick, Caloric, Ikea Often Replaced With 691366 Idler Pulley, 349241T Drum Rollers Installation Notes ⚠️ Safety First — Unplug Dryer Before Starting Unplug the dryer from the power source (and shut off the gas supply for gas dryers) before beginning any repair. Remove the lint screen, then unscrew the two Phillips screws inside the lint filter housing. Use a putty knife 2 inches from each front corner to release the top panel clips and lift the top panel. Remove the front panel to access the drum. Release belt tension at the idler pulley, lift the drum slightly, and slide the old belt off. Loop the new 341241 belt around the drum with the ribbed side facing down (toward the drum). Route the belt around the idler pulley and motor pulley — consult your model's service manual or a model-specific video for the correct belt path. Reassemble and run a test cycle. Tip: While the drum is out, inspect and replace the idler pulley (691366) and drum rollers (349241T) if worn. Tools needed: Phillips screwdriver, putty knife or flat pry tool. Frequently Asked Questions How does the 341241 differ from the W10205415 and 6602-001655 belts? All three are 92-inch dryer drum belts, but they differ in width and rib count. The 341241 is 1/4" wide with 4 ribs and 3 grooves. The W10205415 is 3/8" wide with 5 ribs and 4 grooves. The 6602-001655 is 5/16" wide with 5 ribs and 4 grooves designed for Samsung dryers. Always match the part number to your specific model — do not substitute based on appearance alone. Will this belt fit my Kenmore dryer? Many Kenmore dryers — especially the popular 110-series — are manufactured by Whirlpool and use the 341241 belt. Check your model number against the compatibility list and contact our support team if you need help confirming the fit before ordering. How do I know if my drum belt needs to be replaced? The most obvious sign is that the dryer motor hums but the drum does not spin. You may also notice a thumping or slapping sound during operation, a burning rubber smell, or clothes that are damp after a full cycle. Open the dryer cabinet to visually confirm if the belt is broken, frayed, or stretched. Should I also replace the idler pulley and drum rollers? Yes — since the dryer is already disassembled, it is highly recommended to inspect and replace the idler pulley (691366) and drum support rollers (349241T) at the same time. These parts wear at a similar rate and replacing all three together — often sold as a repair kit — prevents having to disassemble the dryer again in the near future. Is this an OEM or aftermarket part? This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It is the exact same belt that came installed in your dryer from the factory — same materials, dimensions, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

XPARTCO W10810403 Washer Lid Switch Assembly The XPARTCO W10810403 is an aftermarket replacement lid lock assembly for Whirlpool Cabrio and Maytag Bravos XL top-load washers. Positioned on the underside of the washer lid, this assembly detects whether the lid is open or closed and locks it shut during the wash cycle, preventing the washer from spinning or agitating — and preventing the lid from being opened — while the cycle is running. This is a safety mechanism as much as a functional one, keeping users from contacting moving parts or being splashed by water or detergent mid-cycle. This assembly includes the lid lock mechanism and its wiring harness, and ships with a white bezel. Many of these lid locks also contain an internal fuse as part of the switch circuit — if that fuse blows, the symptom isn't limited to lid-related errors; it can prevent the entire control board from powering up at all, since the switch sits in the same circuit path. A failing lid lock typically shows up as the lid not closing or locking properly, the washer failing to start, the cycle stopping mid-way, or in more severe cases, a completely unresponsive control panel with no lights at all. It directly replaces AP5984435, PS11722981, W10648012, W10787878, W10697793, W10787880, AP5999414, and PS11731620. Quick Answer The XPARTCO W10810403 Washer Lid Switch Assembly fixes Whirlpool Cabrio, Maytag Bravos XL, and select Kenmore 600/700 Series top-load washers where the lid won't lock, the washer won't start, the cycle stops mid-way, or the control panel is completely unresponsive with no lights. White bezel. Replaces AP5984435, PS11722981, W10648012, W10787878, W10697793, W10787880, AP5999414, PS11731620. If your original lock has a grey bezel, you need part number W10861642 instead — same mechanism, different bezel color, so match the color of your existing lock before ordering. Common Problems This Part Fixes Lid won't lock or lock reliably during the cycle Lid won't open after a cycle finishes Washer won't start Washer won't agitate or spin because the lid isn't sensed as locked Cycle stops partway through Washer pumps but won't spin Control panel completely unresponsive with no lights, potentially from an internal fuse in the switch circuit Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This washer lid switch assembly directly replaces the following OEM and cross-reference part numbers: W10810403, 4283179, W10632841, W10637463, W10648012, W10787836, W10787878, AP5984435, AWP41491, EAP11722981, PD00028176, PS11722981 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This lid switch assembly is compatible with select Whirlpool Cabrio and Maytag Bravos XL top-load washers, and also fits select Roper, Admiral, Hardwick, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, Norge, Modern Maid, Amana, Kenmore, KitchenAid, Caloric, and Ikea washers built on the same platform, including model numbers such as MVWB855DW1, MVWB865GW1, MVWB835DW3, and MVWB765FW4. Note — bezel color and lid lock platform both matter: This assembly has a white bezel. If your original lock has a grey bezel, order W10861642 instead — same lock mechanism, different bezel color. Separately, Whirlpool has used several distinct lid lock designs across its Cabrio-era washer lineup, including a different 3-wire electronic lock (our W11670519 listing) used on other Cabrio/MVW models. These are not the same part despite both serving Cabrio-platform washers. Always verify your full model number and match your original lock's exact part number before ordering. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement lid lock assembly — includes the lock mechanism and wiring harness Resolves "lid won't lock," "washer won't start," "cycle stops mid-way," and "unresponsive control panel" symptoms White bezel finish Safety mechanism that prevents lid opening and drum movement from occurring at the same time Direct drop-in replacement — mounts to the original position on the underside of the lid Replaces W10810403, 4283179, W10632841, W10637463, W10648012, W10787836, W10787878, AP5984435, AWP41491, EAP11722981, PD00028176, PS11722981 Compatible with Whirlpool, Maytag, Roper, Admiral, Hardwick, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, Norge, Modern Maid, Amana, Kenmore, KitchenAid, Caloric, and Ikea top-load washers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number XPW10810403 OEM Part Number W10810403 Part Type Washer Lid Lock/Switch Assembly Condition Aftermarket Replacement Application Whirlpool Cabrio / Maytag Bravos XL Top-Load Washers Bezel Color White (grey bezel = W10861642) Included Components Lid lock mechanism + wiring harness Location Underside of the washer lid Repair Difficulty Easy — basic hand tools Quantity 1 lid switch assembly Compatible Brands Whirlpool, Maytag, Roper, Admiral, Hardwick, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, Norge, Modern Maid, Amana, Kenmore, KitchenAid, Caloric, Ikea Installation Notes ⚠️ Unplug Washer Before Starting Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Open the washer lid and locate the lid lock assembly mounted on its underside, typically secured with a couple of screws. Photograph the wiring harness connection before disconnecting anything. Remove the mounting screws, disconnect the wiring harness connector from the old assembly, and pull it free. Install the new W10810403 in the same position, reconnect the wiring harness connector fully, and secure the mounting screws. Restore power and run a test cycle to confirm the lid locks securely, the washer starts and completes a full cycle, and the lid unlocks normally once finished. Tools needed: multi-screwdriver, work gloves. Frequently Asked Questions My control panel has no lights at all. Could the lid lock really cause that? Yes, and this is a less obvious but documented cause. Some of these lid lock assemblies include an internal fuse as part of the switch circuit. If that fuse blows, it can prevent the control board from powering up entirely, producing a completely dark, unresponsive panel rather than a symptom that's obviously tied to the lid. If your washer has no lights and no response at all, this lock assembly is worth checking alongside the more obvious suspects. My old lock has a grey bezel. Can I still use this part? This specific listing has a white bezel. If your original lock is grey, order part number W10861642 instead — it's the same lock mechanism, just finished with a grey bezel to match certain washer trim colors. Using the wrong bezel color won't affect function, but it will look mismatched against your washer's lid. Is this the same lock used on all Cabrio washers? No — Whirlpool has used more than one lid lock design across its Cabrio-era lineup. This W10810403 is a distinct assembly from other Cabrio/MVW-platform locks, such as our W11670519 listing, which uses a different 3-wire electronic locking design. Always match your exact original part number rather than assuming any "Cabrio lock" will fit, since the mounting and electrical interface can differ between designs. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the locking mechanism, wiring harness, and bezel design of the original W10810403 lid lock assembly used in compatible Whirlpool Cabrio, Maytag Bravos XL, and related top-load washers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

279769 Dryer Thermostat Kit - Compatible with Whirlpool, Kenmore, Maytag Product Description Keep your dryer running safely with the replacement 279769 Dryer Thermostat Kit. This kit is designed for select Whirlpool, Kenmore, Maytag, Roper, Estate, KitchenAid, and other dryers, featuring a high-limit thermostat (L250-80F) and a thermal cut-off fuse (352F) to prevent overheating. It addresses issues like no heat, not enough heat, overheating, or failure to start, offering a cost-effective alternative to OEM parts. Note: Includes one high-limit thermostat, one thermal cut-off fuse. Disconnect power before installation. Check dryer venting for blockages to prevent repeat failures. Replaces part numbers: 279769, 2004, 279548, 2796769, 279769VP, 2821, 3387812, 3389946, 3398671, 3977394, 695563, 80001, SET184, AH334278, EA334278, EAP334278, PD00002485, AP3094224, PS334278. Compatibility: Compatible with models including but not limited to: Whirlpool: NGD4655EW, WGD4815EW, WGD5000DW, MGDC215EW, MGDX655DW Kenmore: 110.60022010, 110.70102312, 110.78002012 Maytag: MEDC215EW1, MGDX655DW1 Roper: RED4640YQ0 Estate: EED4400WQ0 KitchenAid: YKEHS01PMT0 Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Whirlpool, Kenmore, Maytag, Roper, Estate, KitchenAid, and other dryers. 🔥 Specifications: High-limit thermostat (L250-80F), thermal cut-off fuse (352F). 💰 Cost-Effective Alternative: Offers OEM-equivalent performance at a lower price. 🛠️ Easy Installation: Requires screwdriver, pliers, work gloves; typically installed in 15–20 minutes. 🛡️ Effective Fixes: Resolves no heat, not enough heat, overheating, or failure to start. Product Specification Part Number: 279769 Component Type: Dryer thermostat kit Material: Metal and plastic Dimensions: High-limit thermostat: 2" L x 1-1/2" W; Thermal cut-off fuse: 2" L x 1-1/2" W (Based on web:6, web:16) Weight: 2.4 oz (Based on web:1, web:15) Electrical Specs: High-limit thermostat: L250-80F (121°C); Thermal cut-off fuse: 352F (178°C) Mounting: Screw-mounted on heater housing. Operating Conditions: Suitable for high-heat dryer environments Compliance: Prop 65 warning for California Installation Notes: Safety First: Disconnect the dryer from the power source before installation. Shop for high-quality replacement appliance parts with a 30-day return policy. Keep your dryer running safely today! Add to cart now for a budget-friendly fix!

Read more less

XPARTCO 280148 Dryer Thermostat Set The XPARTCO 280148 is an aftermarket replacement thermal fuse and high-limit thermostat set for Whirlpool electric dryers, and also fits select Kenmore, Maytag, Amana, Roper, Estate, Crosley, Admiral, KitchenAid, and Norge models. This set bundles the 8557403 high-limit thermostat, which monitors temperature and automatically cuts power to the heating element if it overheats, then resets itself once the dryer cools, together with the 8318314 thermal fuse, a one-time backup safety device that permanently opens the circuit if temperatures climb high enough that the thermostat alone doesn't prevent an overheat. These two parts are sold together and commonly fail around the same time, since they protect the same circuit and respond to the same underlying overheating conditions — most often restricted exhaust venting. Symptoms include the dryer not heating at all, taking longer than normal to dry a load, or overheating before shutting down. It directly replaces 280148VP, 1175772, AP3874047, PS991443, EAP991443, and 314634. Quick Answer The XPARTCO 280148 Dryer Thermostat Set fixes Whirlpool, Kenmore, Maytag, Amana, Roper, Estate, Crosley, Admiral, KitchenAid, and Norge electric dryers with no heat, drying that takes too long, or a dryer that overheats before shutting down. Includes the 8557403 high-limit thermostat (auto-resetting) and 8318314 thermal fuse (one-time). Replaces 280148VP, 1175772, AP3874047, PS991443, EAP991443, 314634. Always inspect and clean the exhaust venting when replacing this set — a blown thermal fuse is a symptom of restricted airflow, and skipping the vent check leads to repeat failures. What's In The Set Component Type Function 8557403 High-Limit Thermostat Auto-resetting Cuts power to the heating element if temperature exceeds safe limits, resets automatically once the dryer cools. 8318314 Thermal Fuse One-time, non-resettable Backup safety device — permanently opens the circuit if temperature exceeds safe limits. Must be replaced once blown. Common Problems This Set Fixes Dryer runs but produces no heat at all Dryer won't start at all — no lights, no tumble, no response Drying takes noticeably longer than it used to Dryer overheating before shutting down Dryer that stopped working suddenly after running unusually hot Repeated thermal fuse failures on a dryer with a known venting issue Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer thermostat set directly replaces the following OEM and cross-reference part numbers: 280148, 1175772, 280148VP, PD00002627, FIX991443, EAP991443, AH991443, AP3874047, AWP39427, EA991443, PS991443, 8318314, WP8557403, 8557403, 1180102, AP6013164, AWP48681, PD00003588, PS11746386 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This thermostat set is compatible with select Whirlpool electric dryers, and also fits select Kenmore, Maytag, Amana, Roper, Estate, Crosley, Admiral, KitchenAid, and Norge dryers built on the Whirlpool platform, including model numbers such as: 7MWED5620HW0, 7MWED5620HW1, 7MWED6613HC0, 7MWED6613HC1, 7MWED6613HW0, 7MWED6613HW1 MED5500FC1, MED5500FC2, MED5500FW1, MED5500FW2 MED5630HC0, MED5630HC1, MED5630HC2, MED5630HW0, MED5630HW1, MED5630HW2 MED6000XG0, MED6000XG1, MED6000XG2, MED6000XR0, MED6000XR1, MED6000XW0, MED6000XW1, MED6000XW2 MED6630HC0, MED6630HC1, MED6630HC2, MED6630HW0, MED6630HW1, MED6630HW2 MED7000XG0, MED7000XG1, MED7000XR0, MED7000XR1, MED7000XW0, MED7000XW1, MED7000XW2 MED7230HC0, MED7230HC1, MED7230HC2, MED7230HC3, MED7230HW0, MED7230HW1, MED7230HW2, MED7230HW3 MED8200FC1, MED8200FC2, MED8200FW1, MED8200FW2 Note: Always verify your full model number before ordering, since Whirlpool uses several different thermostat and fuse designs across its dryer lineup. This set is commonly purchased alongside heating element WP8544771. Contact our support team with your model number if you're unsure. Key Features 2-piece set: 8557403 auto-resetting high-limit thermostat and 8318314 one-time thermal fuse Resolves "no heat," "won't start at all," "takes too long to dry," and "overheating" symptoms Addresses two overheat-protection thresholds in the same circuit at once Commonly purchased alongside heating element WP8544771 No special tools required for installation Replaces 280148VP, 1175772, AP3874047, PS991443, EAP991443, and 314634 Compatible with Whirlpool, Kenmore, Maytag, Amana, Roper, Estate, Crosley, Admiral, KitchenAid, and Norge electric dryers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Set Part Number 280148 OEM Part Number 280148 Set Contents 1x High-Limit Thermostat (8557403), 1x Thermal Fuse (8318314) Condition Aftermarket Replacement Application Whirlpool Electric Dryers High-Limit Thermostat Type Automatically resetting Thermal Fuse Type One-time use, non-resettable Companion Heating Element WP8544771 (commonly used together) Repair Difficulty Easy to Moderate — no special tools required Compatible Brands Whirlpool, Kenmore, Maytag, Amana, Roper, Estate, Crosley, Admiral, KitchenAid, Norge Installation Notes ⚠️ Unplug Dryer Before Starting — Inspect And Clean The Venting Before Reassembling Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access is typically through the rear panel, near the heating element and blower housing where both components are mounted. Photograph the wiring connections before disconnecting anything, since the thermostat and fuse can be easy to swap positions by mistake. Remove each old component from its mounting position, noting orientation, and disconnect its wiring. Before reassembling, fully inspect and clean the dryer's exhaust vent, from the lint trap housing all the way to the exterior vent hood, checking for lint buildup, crushed sections, or excessive length. Restricted airflow is the leading cause of failure for both of these components, and skipping the vent check often leads to repeat failures even with new parts installed. Install the new 8557403 thermostat and 8318314 thermal fuse from this set in the same positions as the parts they replace, reconnecting wiring exactly as photographed. Reassemble the panel, restore power, and run a full test cycle to confirm normal, consistent heating with no premature shutoffs. Tools needed: Phillips or nut driver (model-dependent), work gloves. Frequently Asked Questions Why replace both the thermostat and the fuse together instead of just the one that failed? These two parts protect the same circuit at different thresholds and tend to fail from the same underlying cause. If the high-limit thermostat isn't regulating temperature correctly, the thermal fuse often ends up blowing as the backup safety measure. Replacing only one risks the other failing again shortly after, so they're sold and serviced together as a set. I replaced this set and the dryer failed again. What should I check? This is a strong sign the underlying cause — almost always restricted airflow — was never addressed. Thoroughly inspect and clean the entire exhaust path from the lint trap housing to the outside vent hood, checking for lint buildup, crushed or kinked ductwork, or a vent run that's too long. Failing to correct a venting issue will cause repetitive failures of this set even when it's brand new. Should I replace the heating element at the same time? It's worth considering if your dryer's heating element (commonly WP8544771 on compatible models) is original and has been running alongside a failing thermostat, since sustained overheating can stress the element as well. It's not required, but since you'll already have the panel open for this repair, it's a reasonable time to inspect the element for visible damage. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the temperature thresholds and mounting configuration of the original 280148 high-limit thermostat and thermal fuse set used in compatible Whirlpool, Kenmore, Maytag, Amana, Roper, and related electric dryers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

EXP694 Dryer Repair Kit Replaces DC97-16782A, 6602-001655, DC93-00634A The EXP694 Dryer Repair Kit is a complete drum system rebuild solution designed to restore smooth, quiet, and efficient dryer operation. This kit includes the most common wear components found inside your dryer: drum belt, idler pulley, and drum support rollers. Over time, these parts wear down together, causing squeaking, grinding, drum slippage, or complete failure to spin. Replacing all components at once ensures proper alignment, eliminates noise, and prevents repeat breakdowns — making this the most effective long-term repair solution. Quick Answer The EXP694 Dryer Repair Kit fixes dryers that won’t spin, make loud squeaking or grinding noises, or stop tumbling. It replaces the belt, rollers, and idler pulley to restore smooth and quiet drum operation. Note: Includes four rollers (each with shaft and two tri-rings), one idler pulley, and one belt. Replace all four rollers for even wear. Inspect the drum and felt seal (e.g., DC97-07618A) for wear. Clean lint from the drum and cabinet to prevent overheating. Common Problems This Part Fixes Dryer drum not spinning or slipping Loud squeaking, grinding, or thumping noises Uneven or slow drum rotation Dryer stopping mid-cycle Excessive vibration or instability Worn belt, rollers, or idler pulley components Replaces Part Numbers This repair kit replaces the following common drum system components: Drum Roller: DC97-16782A, AP5325135, DC97-16782C, DC97-16782D, 2027851, DC97-07523A, DC97-07523B, PS4221885, WPW10177428, AP6016361, W10177428, 35001136, DC97-07523A, PS11749648 Idler Pulley: DC93-00634A, AP6038887, DC96-00882C, DC61-01230B, DC96-00882B, PS11771601, 12002777, AP4010261, 1401171, 35001083, 35001098, 35001276, AH2004052, DC61-01215A, DC96-00882B, EA2004052, PS2004052 Drum Belt: 6602-001655, AP4373659, 1935594, 6602-001314, PS4133825, WPW10205415, AP6017004, W10205415, 35001137, 6602-001314, PS11750299 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This repair kit is compatible with select dryers from the following brands: Samsung dryers (gas and electric models) Kenmore / Sears dryers (select models built on Samsung platform) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Complete drum repair kit including belt, rollers, and idler pulley OEM-equivalent fit, performance, and durability Eliminates noise and restores smooth drum rotation Prevents repeat repairs by replacing all wear components together Cost-effective all-in-one repair solution DIY-friendly installation with basic tools Product Specifications Includes 4 drum rollers (DC97-16782A, ~3-1/4" diameter x 1-1/8" width, blue/black plastic/rubber, metal shaft, self-lubricating bushing with ball bearing, each with shaft and two tri-rings), 1 idler pulley (DC93-00634A, metal/plastic), 1 drum belt (6602-001655, 92" long, 5 ribs, neoprene), kit dimensions ~10"L x 6"W x 4"H. Part Type Dryer Repair Kit Includes Belt, Rollers, Idler Pulley Application Dryer Drum System Condition Aftermarket Replacement Compatible Brands Samsung, Kenmore Installation Notes ⚠️ Safety First — Unplug Dryer Before Starting Disconnect power before servicing. Remove dryer panels, release belt tension, and replace worn components. Ensure proper alignment of the belt and rollers before reassembly. For best results, replace all components included in this kit at the same time. Frequently Asked Questions Should I replace all parts at once? Yes. The belt, rollers, and pulley wear together. Replacing all components ensures smooth operation and prevents future breakdowns. Will this fix dryer noise? Yes. This kit resolves most squeaking, grinding, and thumping noises caused by worn drum components. Is this an OEM part? This is a high-quality aftermarket repair kit built to OEM-equivalent standards for performance and durability. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less