Dryer replacement parts

Choice Manufactured Parts Choice 6602-001655 Dryer Drum Belt for Samsung Aftermarket 92-inch, 5-rib / 4-groove dryer drum drive belt for select Samsung and Kenmore dryers. Product Overview The Choice 6602-001655 dryer drum belt transfers power from the dryer motor pulley to the drum so the drum can rotate during the drying cycle. This Choice Manufactured Parts aftermarket belt is designed as a replacement for Samsung belt 6602-001655 on compatible dryers. Quick Answer 6602-001655CM is a 92-inch, 5-rib / 4-groove aftermarket dryer drum belt for select Samsung and Kenmore dryers. It replaces Samsung 6602-001655 and 6602-001314. Verify the complete dryer model number before ordering. Common Problems This Part May Fix Dryer motor runs but drum does not turn Broken or snapped drum belt Belt is frayed, glazed, cracked, or stretched Thumping or slapping noise from a damaged belt Drum turns intermittently or slips under load Replaces and Cross-References 6602-001655, 6602-001314, 5PH2337, LB1655, ASM874658, PD00002012, EAP2407938, AP4373659, PS4133825, 6602-001655CM, ER6602-001655. Cross-reference numbers are provided for identification. This is a Choice Manufactured Parts aftermarket replacement and is not manufactured by Samsung. Compatibility Fits select Samsung and Kenmore dryers using the 6602-001655 / 5-rib belt configuration. Compatible model examples include: DV203AEW/XAA DV209AEW/XAA DV218AEW/XAA DV42H5200EP/A3 DV42H5600EW/A3 DV45H7000EW/A2 DV45K6500EV/A3 DV50K7500GW/A3 DVE45R6100C/A3 DVE45R6300W/A3 DVG45T6000W/A3 Kenmore 592 Series Important: This is a partial compatibility list. Match the complete dryer model number and original belt number before purchasing. Key Features Choice Manufactured Parts aftermarket replacement 92-inch drum drive belt 5 ribs / 4 grooves Approx. 5/16-inch belt width Ribbed drive surface with smooth outer/back surface For select Samsung and Kenmore dryers Specifications Choice Part Number 6602-001655CM Brand Choice Manufactured Parts Part Type Dryer Drum Drive Belt Condition New Part Quality Aftermarket Replacement Length Approx. 92 in. Width Approx. 5/16 in. Ribs / Grooves 5 Ribs / 4 Grooves Primary Replacement For Samsung 6602-001655 Application Dryer Drum Drive System Installation Notes Disconnect dryer power before service. Access the drum and note the original belt routing before removal. Route the replacement belt around the drum, idler pulley, and motor pulley exactly as the original. Install the ribbed side toward the drum/pulley contact surface as required by the dryer design. Confirm the idler pulley applies proper tension and spins freely. Rotate the drum by hand before reassembly to verify smooth belt tracking. Diagnostic tip: Before installing a new belt, inspect the idler pulley, drum support rollers, motor pulley, and felt seals. A seized or damaged support component can quickly damage a replacement belt. FAQ Is this a Genuine Samsung OEM belt? No. This is a Choice Manufactured Parts aftermarket replacement for Samsung 6602-001655. How long is the belt? Choice specifies this belt at approximately 92 inches long. How many ribs does it have? It has 5 ribs and 4 grooves. Does it replace 6602-001314? Yes. 6602-001314 is a commonly listed earlier/cross-reference number for the 6602-001655 belt family. Does this include the idler pulley? No. This listing is for the drum belt only unless the product package explicitly states otherwise. Shop With Confidence Match your complete dryer model number and original belt number before ordering. Compatibility assistance is available if you are unsure which belt your dryer uses. Choice Replacement92-Inch Belt5 Rib / 4 GrooveCompatibility Support

Read more less

Choice Manufactured Parts Choice 40111201 Dryer Drum Belt Replaces WP40111201 Aftermarket 5-rib / 4-groove dryer drum belt for select Amana, Maytag, Whirlpool-built, Admiral, Crosley, Speed Queen, Magic Chef and related dryers. Product Overview The Choice 40111201 Dryer Drum Belt is an aftermarket replacement for Whirlpool/Maytag part WP40111201. The belt wraps around the dryer drum, motor pulley and idler pulley so the motor can rotate the drum during the drying cycle. A worn, stretched or broken belt can cause the dryer motor to run while the drum does not turn, or may contribute to thumping, slipping or abnormal belt noise. Quick Answer Choice part 40111201CM is a 5-rib, 4-groove belt approximately 93.5 inches long designed to replace WP40111201 / 40111201 on compatible Whirlpool-manufactured dryer platforms. Common Problems This Part May Fix Dryer runs but drum does not turn Drum turns intermittently or slips Broken or visibly cracked belt Stretched belt with poor tension Thumping or squealing related to belt wear Replaces and Cross-References WP40111201, 40111201, 14218936, 40051501, 40051502, 59174, AP6009126, AWP47792, EAP11742271, PD00002505, PS11742271, R0606549, WP40111201VP, 661570V, 661570, 3387610, 3389728, 3393999, 339728, 661570VP, AP5983729, PS11722115 Cross-reference numbers are provided for identification. This is a Choice Manufactured Parts aftermarket replacement and is not a Genuine Whirlpool OEM belt. Compatibility Designed for select dryers manufactured under Amana, Maytag, Whirlpool, Admiral, Crosley, Speed Queen, Magic Chef and related brands. Compatible model examples include: SDE405DAYW SDE305DAYW LGA30AW/PLGA30AW LE4807L/P1163706WL NG4819L53738 LEA20AL-PLEA20AL SLG332RAW LG3412L/P1122505WL LE2102L/P1118302WL Important: This is only a partial compatibility list. Verify the full dryer model number and original belt number before ordering. Similar-looking belts can differ in length, width and rib count. Key Features Choice Manufactured Parts aftermarket replacement Replaces WP40111201 / 40111201 5 ribs / 4 grooves Approx. 93.5-inch belt length Designed to restore proper drum rotation Fits many Whirlpool-manufactured dryer platforms Product Specifications Choice Part Number 40111201CM Listing Part Number 40111201 Brand Choice Manufactured Parts Part Type Dryer Drum Drive Belt Length Approx. 93.5 in. Ribs 5 Grooves 4 Material Reinforced rubber belt Condition New Part Quality Aftermarket Replacement Installation Notes Disconnect electrical power before servicing the dryer. Access the drum according to the appliance service procedure. Route the new belt around the drum with the ribbed side against the drum where specified by the dryer design. Route the belt around the motor pulley and idler/tension pulley exactly as the original belt was installed. Rotate the drum by hand before reassembly to confirm the belt tracks correctly and is not twisted. Inspect the idler pulley and drum rollers while the dryer is open; worn support parts can shorten belt life. Frequently Asked Questions Is this Genuine Whirlpool OEM? No. This is a Choice Manufactured Parts aftermarket replacement for WP40111201. How long is the belt? Choice specifies this belt at approximately 93.5 inches long with 5 ribs and 4 grooves. What does the dryer belt do? It connects the motor drive system to the drum so the drum tumbles while the dryer operates. Does it replace WP40111201? Yes. Choice 40111201CM is sold as an aftermarket replacement for WP40111201 and 40111201 on compatible models. Shop With Confidence Match the complete appliance model number and original belt number before ordering. Our compatibility team can help confirm fitment. Choice Replacement5-Rib Belt93.5 in. LengthCompatibility Support

Read more less

XPARTCO 6602-001655 Dryer Drum Belt The XPARTCO 6602-001655 is an aftermarket replacement dryer drum belt compatible with select Samsung and Kenmore dryers. The drum belt wraps around the outside of the dryer drum, loops around the motor pulley and idler pulley, and drives the drum to rotate during every drying cycle. Without a functioning belt, the drum cannot spin and clothes will not tumble or dry. Made from premium neoprene rubber reinforced with polyester cords, this 5-rib belt measures 92 inches long x 5/16 inch wide and is built to resist cracking, stretching, and wear under the high heat and repeated tension cycles of daily dryer use. It is a direct drop-in replacement for OEM part numbers 6602-001655 and 6602-001314, and installs in 30–45 minutes with basic hand tools. Quick Answer The XPARTCO 6602-001655 Dryer Drum Belt fixes dryers where the drum is not spinning, clothes are not tumbling, or a thumping/squealing noise is coming from the dryer during operation. It drives the drum via the motor and idler pulleys. Compatible with select Samsung and Kenmore dryers. Measures 92" L x 5/16" W with 5 ribs and 4 grooves. Common Problems This Part Fixes Dryer drum not spinning — motor runs but drum stays still Clothes not tumbling during the drying cycle Thumping, squealing, or slapping noise during operation Dryer runs but produces no heat because drum is stationary Visible broken or frayed belt pieces found inside the dryer cabinet Dryer shuts off shortly after starting due to drum not rotating Replaces Part Numbers This drum belt directly replaces the following OEM and cross-reference part numbers: 6602-001655, 6602-001314, 5PH2337, LB1655, ASM874658, PD00002012, EAP2407938, AP4373659, PS4133825. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drum belt is compatible with select dryers from the following brands: Samsung dryers (gas and electric) Kenmore / Sears dryers (select models) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Drives the dryer drum via the motor pulley and idler pulley for smooth, consistent tumbling every cycle 92" length x 5/16" width — 5-rib, 4-groove design for a secure, slip-free grip on the pulleys Made from premium neoprene rubber with polyester cord reinforcement — resists cracking, stretching, and heat damage Direct replacement for OEM part numbers 6602-001655 and 6602-001314 — no modification required Aftermarket replacement built to OEM-equivalent quality standards DIY-friendly repair — installs in 30–45 minutes with basic hand tools Often replaced together with the idler pulley (DC93-00634A) and drum rollers (DC97-16782A) for a complete drum drive repair Product Specifications Part Number 6602-001655 Part Type Dryer Drum Drive Belt Condition Aftermarket Replacement Application Gas and Electric Dryers Length 92 inches Width 5/16 inch Height 1/8 inch Ribs 5 ribs, 4 grooves Material Neoprene rubber with polyester cord reinforcement Color Black Compatible Brands Samsung, Kenmore Often Replaced With DC93-00634A Idler Pulley, DC97-16782A Drum Rollers Installation Notes ⚠️ Safety First — Unplug Dryer Before Starting Unplug the dryer from the power source (and shut off the gas supply for gas dryers) before beginning any repair. To access the drum belt, remove the top panel and front panel of the dryer. Lift the drum out of the cabinet, remove the old belt, and loop the new 6602-001655 belt around the drum with the ribbed side facing inward. Route the belt slack around the idler pulley and motor pulley — consult your dryer's service manual or a model-specific video for the correct belt path around the pulleys. Reassemble the front panel, top panel, and restore power before running a test cycle. Tip: While the drum is out, this is an ideal time to also inspect and replace the idler pulley and drum support rollers if worn. Tools needed: Phillips screwdriver, putty knife or flat pry tool. Frequently Asked Questions Will the 6602-001655 fit my Samsung or Kenmore dryer? This belt is compatible with select Samsung and Kenmore dryers. Use the model search above to verify your model number, or contact our support team before ordering. What does the dryer drum belt do? The drum belt wraps around the outside of the dryer drum and connects to the motor pulley and idler pulley. As the motor spins, it drives the belt which causes the drum to rotate, tumbling your clothes through the heated air to dry them. A broken or worn belt means the drum cannot spin. How do I know if my drum belt is broken? The most obvious sign is that the dryer motor runs and you can hear it humming, but the drum does not spin. You may also hear a thumping or slapping sound if the belt is slipping or partially broken. Opening the dryer cabinet and visually inspecting the belt will confirm if it is broken, frayed, or stretched. Should I replace the idler pulley and drum rollers at the same time? Yes — since you need to disassemble the dryer to replace the belt anyway, it is highly recommended to also inspect and replace the idler pulley (DC93-00634A) and drum support rollers (DC97-16782A) at the same time. These parts wear at a similar rate and replacing all three together prevents having to disassemble the dryer again in the near future. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is made from premium neoprene rubber with polyester cord reinforcement to match the dimensions and performance of the original belt. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO DC93-00634A Dryer Idler Pulley  The XPARTCO DC93-00634A is an aftermarket replacement idler pulley assembly compatible with a wide range of Samsung dryers. The idler pulley rides against the drive belt and keeps it under proper tension as it wraps around the drum and motor pulley. Over time, the pulley wheel can wear, crack, or seize on its shaft, or the spring-loaded tensioner arm can bend or break, causing the belt to lose tension. When this part fails, the dryer commonly won't spin at all even though the motor runs, makes a loud noise from the drive area, or the belt goes slack and starts slipping. It directly replaces DC93-00634A, DC97-07509B, DC61-01230B, DC96-00882B, DC96-00882C, 4455850, AP6038887, ASM34631, EAP11771601, PD00032419, PS11771601. Installs in 30 minutes to 2 hours depending on how much disassembly your model requires. Quick Answer The XPARTCO DC93-00634A Dryer Idler Pulley fixes Samsung dryers that won't spin the drum even though the motor runs, make a loud noise from the drive belt area, or have a loose/slipping belt. Replaces DC93-00634A, DC97-07509B, DC61-01230B, DC96-00882B, DC96-00882C, 4455850, AP6038887, ASM34631, EAP11771601, PD00032419, PS11771601. Classic symptom: motor hums and runs, but the drum doesn't turn — "no spin, no start." Common Problems This Part Fixes Dryer motor runs but the drum doesn't spin ("no spin, no start") Loud noise or rattling coming from the drive belt/motor area Drive belt slipping, loose, or off-track Visible cracks, wear, or seizing on the pulley wheel Bent or broken tensioner arm/spring Squeaking noise from the pulley as it rotates Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This idler pulley directly replaces the following OEM and cross-reference part numbers: DC93-00634A, DC97-07509B, DC61-01230B, DC96-00882B, DC96-00882C, 4455850, AP6038887, ASM34631, EAP11771601, PD00032419, PS11771601 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This idler pulley is compatible with a wide range of Samsung dryers, including: Samsung DV337AEG/XAA-0000 Samsung DV45H7000EW/A2-0000 Samsung DV45K6200EZ/A3 Samsung DV203AEW/XAA-0000, DV203AGS, and related models Note: This idler pulley is specific to the Samsung drive belt platform and does not fit LG, Whirlpool, GE, or other brands, which use different pulley designs. Always verify your appliance model number before ordering. Contact our support team with your model number if you're unsure. Key Features Direct-fit replacement Samsung dryer idler pulley assembly Resolves "no spin, no start," "loud noise," and "loose/slipping belt" symptoms Maintains proper belt tension as the belt wraps around the drum and motor pulley Spring-loaded tensioner arm matches original design for correct belt tension Replaces DC93-00634A, DC97-07509B, DC61-01230B, DC96-00882B, DC96-00882C, 4455850, AP6038887, ASM34631, EAP11771601, PD00032419, PS11771601 Compatible with a wide range of Samsung dryer models Aftermarket replacement built to OEM-equivalent quality standards Exact-fit design — no modification needed for installation Product Specifications Part Number XPDC93-00634A OEM Part Number DC93-00634A Part Type Dryer Idler Pulley Assembly Condition Aftermarket Replacement Function Maintains drive belt tension Application Samsung Dryer Drive Belt System Compatible Brand Samsung Installation Notes ⚠️ Unplug Dryer Before Starting Disconnect power before beginning. Remove the front panel and/or top panel as needed to access the drum and drive belt (access point varies by model). Photograph the belt routing before removing anything. Relieve tension on the drive belt by pressing the idler pulley toward the motor, then slip the belt off the pulley and motor shaft. Remove the mounting screw or clip holding the idler pulley bracket in place and remove the old pulley assembly. Install the new DC93-00634A pulley in the same position and secure it. Route the new belt back around the drum and motor pulley, using the idler pulley to apply tension, matching your photos of the original routing. Reassemble any panels removed for access, restore power, and run a test cycle to confirm the drum spins smoothly and quietly. Tools needed: Phillips or nut driver, putty knife (for panel clips, if applicable). Frequently Asked Questions My dryer's motor runs but the drum won't spin — is this the part? This is the classic "no spin, no start" symptom of a failed idler pulley or a broken drive belt. If the pulley wheel is cracked, seized, or the tensioner arm is bent or broken, the belt loses tension and can no longer transfer power from the motor to the drum. Inspect the belt for damage as well, since a broken belt often accompanies a worn idler pulley. Do I need to replace the drive belt at the same time? Not necessarily, but it's worth inspecting closely while you have the drum accessible. If the idler pulley failed due to age or wear, the belt has often experienced similar stress and may be worn, glazed, or close to failing itself. Many technicians replace both together to avoid a repeat repair. Will this fit my LG or Whirlpool dryer? No — this idler pulley is specific to the Samsung drive belt platform. LG, Whirlpool, GE, and other brands use different idler pulley and belt tensioning designs that are not interchangeable with this part. Confirm your appliance model number before ordering. How long does this repair typically take? Most installers report 30 minutes to 2 hours depending on how much disassembly your specific model requires to access the belt and pulley. Front panel removal is usually the more time-consuming part; the pulley swap itself is quick once accessed. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

WP3392519 Genuine OEM Whirlpool Dryer Thermal Fuse The WP3392519 is a genuine Whirlpool OEM thermal fuse mounted on the blower housing next to the blower fan. This fuse is a one-time safety device: as long as the dryer stays within its normal operating temperature, it does nothing at all, but the instant internal temperatures climb high enough — almost always from restricted airflow — the fuse permanently opens the circuit and cuts power to the dryer. That's why a blown thermal fuse produces such a specific symptom: the dryer won't start at all, with no lights, no tumble, and no response, even though the outlet has power. This fuse opens at approximately 196°F (91°C) and terminates in two 3/16" wire terminals for a direct plug-in fit. Unlike a resettable thermostat, this thermal fuse cannot be reset once it blows — it must be replaced. A blown thermal fuse is almost always a symptom rather than a random failure: restricted exhaust venting is the leading cause, since trapped heat is exactly what the fuse is designed to react to. A shorted heating element or a failed regulating thermostat can also cause the dryer to run hot enough to blow the fuse. It directly replaces 3392519, WP3392519VP, AP6008325, 3388651, 694511, ET401, PS11741460, EAP11741460, AH11741460, EA11741460, PD00002311, G4AP0500, and 80005. Quick Answer The WP3392519 Genuine OEM Whirlpool Dryer Thermal Fuse fixes Whirlpool, Maytag, Kenmore, KitchenAid, Roper, Jenn-Air, and Amana dryers that won't start at all — no lights, no tumble, no response to any button. Opens at approximately 196°F (91°C). Two 3/16" wire terminals. Replaces 3392519, WP3392519VP, AP6008325, 3388651, 694511, ET401, PS11741460, EAP11741460, AH11741460, EA11741460, PD00002311, G4AP0500, 80005. Always inspect and clean the dryer venting when replacing this fuse — a blown fuse is a symptom of restricted airflow, and installing a new fuse without fixing the vent will likely blow it again. Common Problems This Part Fixes Dryer won't start at all — no lights, no tumble, no response to any button Dryer that stopped working suddenly, especially after running unusually hot Dryer runs a short time then shuts off completely and won't restart Repeated blown fuses on a dryer with a known venting or airflow restriction Clothes coming out extremely hot right before the dryer stopped working Dryer that recently smelled like burning or overheating before failing Continuity test shows an open circuit across the old fuse Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer thermal fuse directly replaces the following OEM and cross-reference part numbers: 3392519, WP3392519, 3388651, WE4X857, G4AP0500, 6L4101, 6L4101091C, ET401, 3388651, 694511, 80005, AWP47582, PD00002311, EAP11741460, AP6008325, PS11741460 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This thermal fuse is compatible with select Whirlpool-built dryers across the Whirlpool family of brands, including: Whirlpool electric and gas dryers — WED, WGD series Maytag electric and gas dryers — MEDC, MGDC series (select Whirlpool-built models) Kenmore dryers (select Whirlpool-built models) KitchenAid, Jenn-Air, and Amana dryers (select models) Roper, Estate, Inglis, and Crosley dryers (select models) Verified model numbers include: MEDC465HW0, MGDC465HW0, WED4850HW0, WED4950HW0, WED49STBW1, WET4024HW0, WET4124HW0, WGD4850HW0, WGD4950HW0, YMEDC465HW0, YWED4850HW0, and YWET4024HW0. Note: This fuse also fits select commercial and stacked washer/dryer combination units on the Whirlpool platform. Always verify your full model number before ordering. Contact our support team with your model number if you're unsure. Key Features Genuine Whirlpool OEM part — factory-specified opening temperature and terminal configuration One-time safety device that cuts power if the dryer overheats Opens at approximately 196°F (91°C) Resolves "won't start at all," "stopped working suddenly," and "clothes came out extremely hot before it died" symptoms caused by a blown fuse Two 3/16" wire terminal connectors for a direct plug-in electrical fit Mounts to the blower housing next to the blower fan Replaces 3392519, WP3392519VP, AP6008325, 3388651, 694511, ET401, PS11741460, EAP11741460, AH11741460, EA11741460, PD00002311, G4AP0500, and 80005 Compatible with Whirlpool, Maytag, Kenmore, KitchenAid, Roper, Jenn-Air, and Amana dryers Genuine OEM replacement — guaranteed fit, materials, and performance Product Specifications Part Number WP3392519 Part Type Dryer Thermal Fuse (Thermal Cut-Off) Condition Genuine OEM Brand Whirlpool Opening Temperature Approx. 196°F (91°C) Location Blower housing, next to the blower fan Terminals 2 (3/16" wire terminals) Resettable No — one-time use, must be replaced once blown Dimensions Approx. 2" x 1/2" Repair Difficulty Medium — basic disassembly required Quantity 1 thermal fuse Compatible Brands Whirlpool, Maytag, Kenmore, KitchenAid, Roper, Jenn-Air, Amana, Estate, Inglis, Crosley Installation Notes ⚠️ Unplug Dryer Before Starting — Inspect And Clean The Venting Before Reassembling Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access is typically through the rear panel: remove the screws securing the panel to reach the blower housing where the fuse is mounted. Photograph the wiring before disconnecting the wire terminals from the old fuse. Remove the mounting screw holding the fuse in place and pull it free, disconnecting both wire terminals. Before installing the new fuse, test it for continuity with a multimeter to confirm it's good out of the box, and test the old one to confirm it's actually blown (no continuity) rather than assuming. This is the most important step: fully inspect and clean the dryer's exhaust vent, from the lint trap housing all the way to the exterior vent hood, checking for lint buildup, crushed sections, or excessive length. A blown thermal fuse is a symptom of restricted airflow, and skipping this step means the new fuse is likely to blow again. Install the new WP3392519 in the same mounting position, reconnect both wire terminals, and secure the mounting screw. Reinstall the rear panel, restore power, and run a test cycle to confirm normal heating and shutoff behavior. Tools needed: Phillips or nut driver (model-dependent), multimeter, vent brush or vacuum attachment for cleaning ductwork, work gloves. Frequently Asked Questions My dryer has no power at all and the lights won't turn on. Is this the thermal fuse? It's a strong possibility. When this thermal fuse blows, it cuts power broadly enough that the console lights and control panel can go completely dark, not just the heating function — that's a normal result of how this fuse is wired into the circuit. Before replacing it, confirm the outlet has power and the breaker hasn't tripped, then check the fuse for continuity with a multimeter. If it shows no continuity, this fuse is the correct fix, though it's also worth checking the exhaust ducting since that's the most common underlying cause. I replaced the fuse and it blew again. What's going on? This is a strong sign that the underlying cause — almost always restricted airflow — was never addressed. Thermal fuses don't fail from age; they blow because the dryer overheated. If a new fuse keeps blowing, thoroughly inspect and clean the entire exhaust path from the lint trap housing to the outside vent hood, checking for lint buildup, crushed or kinked ductwork, or a vent run that's too long. If airflow checks out and the fuse still blows, have the heating element and cycling thermostat checked as well, since a component stuck in the "on" position can also drive excess heat. Can I just reset the thermal fuse instead of replacing it? No. Unlike a cycling thermostat, this thermal fuse is a one-time safety device — once it blows, its internal circuit is permanently broken and it cannot be reset or repaired. Replacement is the only option. My clothes came out extremely hot right before the dryer died. Is that related? Yes, this is a classic warning sign. Clothes coming out unusually hot indicates the dryer was already running hotter than normal, which is exactly the condition that leads to a blown thermal fuse. If you noticed this before the dryer stopped working, it strongly points to a ventilation or airflow problem that should be fully addressed before running the dryer again. Is this an OEM or aftermarket part? This is a genuine OEM part, manufactured by Whirlpool to factory specifications — guaranteed fit, materials, and performance. It matches the original opening temperature, terminal configuration, and mounting position of the thermal fuse originally installed in your dryer. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Genuine OEM Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

341241 Dryer Genuine OEM Drum Belt The 341241 is a Genuine OEM dryer drum belt compatible with a wide range of Whirlpool-family dryers including Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Admiral, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, Norge, Modern Maid, Hardwick, Caloric, and Ikea. The drum belt wraps around the outside of the dryer drum, loops around the motor pulley and idler pulley, and drives the drum to rotate during every drying cycle. Without a functioning belt, the drum cannot spin and clothes will not tumble or dry. Made from high-strength rubber with reinforced ribs, this belt measures 92-1/4 inches long x 1/4 inch wide and features 4 ribs and 3 grooves. It is flat on one side and ribbed on the other, and is built to resist cracking, stretching, and wear under the high heat and repeated tension cycles of daily dryer use. It also replaces some 5-rib, 4-groove belts. Installs in 30–45 minutes with basic hand tools. Quick Answer The 341241 Dryer Genuine OEM Drum Belt fixes dryers where the drum is not spinning, clothes are not tumbling, or a thumping/squealing noise is coming from the dryer. Compatible with Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Admiral, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, and more. Measures 92-1/4" L x 1/4" W with 4 ribs and 3 grooves. Common Problems This Part Fixes Dryer drum not spinning — motor runs but drum stays still Clothes not tumbling during the drying cycle Thumping, squealing, or slapping noise during operation Dryer runs but produces no heat because drum is stationary Burning rubber smell coming from the dryer Visible broken or frayed belt pieces found inside the dryer cabinet Clothes taking too long to dry due to drum not rotating at correct speed Replaces Part Numbers This drum belt directly replaces the following OEM and cross-reference part numbers: 341241, 14210003, 2008, 26000341241, 26000349533, 31001026, 31531589, 3389628, 3392665, 3394651, 3399844, 341241VP, 345473, 349533, 529597, 53-0186, 53-1080, 53-1086, 53-1528, 53-1589, 53-2671, 53-2910, 660996, 660997, 661561, 693306, 694088, 694416, 694868, 695055, 697388, 8066065, 8206, 8210, 920H4, 920H5, 99906951, 99989673, 99989674, FSP341241, LB276, LB279, P46-037, P46-149, W10127457, W10131364, AH346995, AP32, EA346995, ER341241, AWP39161, PD00002263, EAP346995, AP2946843, PS346995, TJ341241. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drum belt is compatible with select dryers from the following brands: Whirlpool dryers (gas and electric) Kenmore / Sears dryers (select models) Maytag dryers KitchenAid dryers Amana dryers Roper dryers Admiral dryers Jenn-Air dryers Estate dryers Magic Chef dryers Crosley dryers Inglis dryers Norge, Modern Maid, Hardwick, Caloric, and Ikea dryers Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Drives the dryer drum via the motor pulley and idler pulley for smooth, consistent tumbling every cycle 92-1/4" length x 1/4" width — 4-rib, 3-groove design; flat on one side, ribbed on the other Also replaces some 5-rib, 4-groove belts — wide cross-compatibility across Whirlpool-family models Made from high-strength rubber with reinforced ribs — resists cracking, stretching, and heat damage Direct replacement for OEM part numbers 341241 and 8066065 — no modification required Compatible with over a dozen major appliance brands built on the Whirlpool platform Genuine OEM part — factory-exact fit, materials, and dimensions DIY-friendly repair — installs in 30–45 minutes with basic hand tools Often replaced together with the idler pulley (691366) and drum rollers (349241T) for a complete drum drive repair Product Specifications Part Number 341241 Part Type Dryer Drum Drive Belt Condition Genuine OEM Application Gas and Electric Dryers Length 92-1/4 inches Width 1/4 inch Ribs 4 ribs, 3 grooves Profile Flat on one side, ribbed on the other Material High-strength rubber with reinforced ribs Color Black Compatible Brands Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Roper, Admiral, Jenn-Air, Estate, Magic Chef, Crosley, Inglis, Norge, Modern Maid, Hardwick, Caloric, Ikea Often Replaced With 691366 Idler Pulley, 349241T Drum Rollers Installation Notes ⚠️ Safety First — Unplug Dryer Before Starting Unplug the dryer from the power source (and shut off the gas supply for gas dryers) before beginning any repair. Remove the lint screen, then unscrew the two Phillips screws inside the lint filter housing. Use a putty knife 2 inches from each front corner to release the top panel clips and lift the top panel. Remove the front panel to access the drum. Release belt tension at the idler pulley, lift the drum slightly, and slide the old belt off. Loop the new 341241 belt around the drum with the ribbed side facing down (toward the drum). Route the belt around the idler pulley and motor pulley — consult your model's service manual or a model-specific video for the correct belt path. Reassemble and run a test cycle. Tip: While the drum is out, inspect and replace the idler pulley (691366) and drum rollers (349241T) if worn. Tools needed: Phillips screwdriver, putty knife or flat pry tool. Frequently Asked Questions How does the 341241 differ from the W10205415 and 6602-001655 belts? All three are 92-inch dryer drum belts, but they differ in width and rib count. The 341241 is 1/4" wide with 4 ribs and 3 grooves. The W10205415 is 3/8" wide with 5 ribs and 4 grooves. The 6602-001655 is 5/16" wide with 5 ribs and 4 grooves designed for Samsung dryers. Always match the part number to your specific model — do not substitute based on appearance alone. Will this belt fit my Kenmore dryer? Many Kenmore dryers — especially the popular 110-series — are manufactured by Whirlpool and use the 341241 belt. Check your model number against the compatibility list and contact our support team if you need help confirming the fit before ordering. How do I know if my drum belt needs to be replaced? The most obvious sign is that the dryer motor hums but the drum does not spin. You may also notice a thumping or slapping sound during operation, a burning rubber smell, or clothes that are damp after a full cycle. Open the dryer cabinet to visually confirm if the belt is broken, frayed, or stretched. Should I also replace the idler pulley and drum rollers? Yes — since the dryer is already disassembled, it is highly recommended to inspect and replace the idler pulley (691366) and drum support rollers (349241T) at the same time. These parts wear at a similar rate and replacing all three together — often sold as a repair kit — prevents having to disassemble the dryer again in the near future. Is this an OEM or aftermarket part? This is a Genuine OEM part manufactured by Whirlpool to factory specifications. It is the exact same belt that came installed in your dryer from the factory — same materials, dimensions, and performance. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Genuine OEM Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

279769 Dryer Thermostat Kit - Compatible with Whirlpool, Kenmore, Maytag Product Description Keep your dryer running safely with the replacement 279769 Dryer Thermostat Kit. This kit is designed for select Whirlpool, Kenmore, Maytag, Roper, Estate, KitchenAid, and other dryers, featuring a high-limit thermostat (L250-80F) and a thermal cut-off fuse (352F) to prevent overheating. It addresses issues like no heat, not enough heat, overheating, or failure to start, offering a cost-effective alternative to OEM parts. Note: Includes one high-limit thermostat, one thermal cut-off fuse. Disconnect power before installation. Check dryer venting for blockages to prevent repeat failures. Replaces part numbers: 279769, 2004, 279548, 2796769, 279769VP, 2821, 3387812, 3389946, 3398671, 3977394, 695563, 80001, SET184, AH334278, EA334278, EAP334278, PD00002485, AP3094224, PS334278. Compatibility: Compatible with models including but not limited to: Whirlpool: NGD4655EW, WGD4815EW, WGD5000DW, MGDC215EW, MGDX655DW Kenmore: 110.60022010, 110.70102312, 110.78002012 Maytag: MEDC215EW1, MGDX655DW1 Roper: RED4640YQ0 Estate: EED4400WQ0 KitchenAid: YKEHS01PMT0 Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Whirlpool, Kenmore, Maytag, Roper, Estate, KitchenAid, and other dryers. 🔥 Specifications: High-limit thermostat (L250-80F), thermal cut-off fuse (352F). 💰 Cost-Effective Alternative: Offers OEM-equivalent performance at a lower price. 🛠️ Easy Installation: Requires screwdriver, pliers, work gloves; typically installed in 15–20 minutes. 🛡️ Effective Fixes: Resolves no heat, not enough heat, overheating, or failure to start. Product Specification Part Number: 279769 Component Type: Dryer thermostat kit Material: Metal and plastic Dimensions: High-limit thermostat: 2" L x 1-1/2" W; Thermal cut-off fuse: 2" L x 1-1/2" W (Based on web:6, web:16) Weight: 2.4 oz (Based on web:1, web:15) Electrical Specs: High-limit thermostat: L250-80F (121°C); Thermal cut-off fuse: 352F (178°C) Mounting: Screw-mounted on heater housing. Operating Conditions: Suitable for high-heat dryer environments Compliance: Prop 65 warning for California Installation Notes: Safety First: Disconnect the dryer from the power source before installation. Shop for high-quality replacement appliance parts with a 30-day return policy. Keep your dryer running safely today! Add to cart now for a budget-friendly fix!

Read more less

XPARTCO 4392065 Dryer Maintenance Kit Replaces 349241T, 341241, WP691366 The XPARTCO 4392065 is an aftermarket dryer maintenance and repair kit containing the three most commonly replaced drum drive components for Whirlpool-family 29-inch dryers including Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Admiral, Estate, Crosley, Inglis, and Magic Chef. The kit includes the drum belt (341241), idler pulley (691366), and rear drum support roller kit (349241T) — the three parts that work together to drive and support the dryer drum, and that most frequently cause squealing, thumping, no heat, and drum-not-spinning issues when worn. Replacing all three parts together in a single repair is the recommended approach — since these components wear at similar rates and the dryer must be fully disassembled to access any one of them, doing all three at once saves significant time and cost compared to replacing them individually. The kit contains everything needed: 1 drum belt, 1 idler pulley, 2 drum support rollers, 4 tri-rings, and 2 retaining washers. Installs in 45–60 minutes with basic hand tools. Quick Answer The XPARTCO 4392065 Dryer Maintenance Kit fixes squealing, thumping, no heat, and drum-not-spinning issues in Whirlpool-family 29" dryers in a single repair. Includes 1x 341241 drum belt (92-1/4" x 1/4", 4 ribs), 1x 691366 idler pulley, 2x 349241T drum rollers, 4x tri-rings, and 2x retaining washers. Compatible with Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Admiral, Estate, Crosley, Inglis, and Magic Chef dryers. Common Problems This Kit Fixes Loud squealing, squeaking, or thumping noise during the drying cycle Dryer drum not spinning — motor runs but belt has broken Clothes not tumbling or drying properly Grinding or rumbling noise from the drum area Dryer drum spinning unevenly or stopping intermittently Belt repeatedly slipping or breaking due to worn idler pulley Drum vibrating excessively due to worn roller bearings What's in the Kit Part 1 of 3 — 1 included 341241 Dryer Drum Belt 92-1/4" L x 1/4" W · 4 ribs, 3 grooves · Neoprene rubber · Wraps around the drum and connects to the idler pulley and motor pulley to drive drum rotation Part 2 of 3 — 1 included 691366 Idler Pulley Sturdy plastic with metal shaft and idler arm · Maintains correct tension on the drum belt between the motor and drum · Self-lubricating bearing Part 3 of 3 — 2 included 349241T Rear Drum Support Roller Kit 2 drum rollers · Reinforced self-lubricating metal bearings, thickened rubber wheel · Supports the rear of the drum as it rotates · Includes 4 tri-rings and 2 retaining washers Replaces Part Numbers Kit (4392065) cross-references: 4392065, 2014, 26000279435, 26000279436, 279435, 279436, 279708, 279708MS, 279709, 279709MS, 279860, 279948, 4392065VP, 587636, 80046, 8106, 8237, 8238, AWP39348, PD00002464, AH373087, EA373087, AP3131942, PS373087. 341241 Belt cross-references: 341241, 14210003, 2008, 26000341241, 26000349533, 31001026, 31531589, 3389628, 3392665, 3394651, 3399844, 341241VP, 345473, 349533, 529597, 53-0186, 53-1080, 53-1086, 53-1528, 53-1589, 53-2671, 53-2910, 660996, 660997, 661561, 693306, 694088, 694416, 694868, 695055, 697388, 8066065, 8206, 8210, 920H4, 920H5, 99906951, 99989673, 99989674, FSP341241, LB276, LB279, P46-037, P46-149, W10127457, W10131364, AH346995, AP32, EA346995, ER341241, AP2946843, PS346995, TJ341241. 691366 Idler Pulley cross-references: WP691366, 691366, 239477, 26000691366, 3346, 337116, 337407, 337510, 3388345, 338946, 3394332, 347034, 347226, 347277, 4319391, 688166, 691366BULK, 8207, 99989677, DE412, K35-163, W10612905, AP6010582, PS11743765. 349241T Drum Roller cross-references: 349241T, 26000349241, 337089, 3389901, 3397588, 3397590, 340352, 3436, 349241, 349241TVP, 661562, 8170, 8205, 99989678, 99989679, AH347627, EA347627, K34-895, AP3098345, PS347627. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This kit is compatible with select 29-inch large-capacity gas and electric dryers from the following brands: Whirlpool dryers (gas and electric) Kenmore / Sears dryers (select Whirlpool-built models) Maytag dryers (gas and electric) Amana dryers KitchenAid dryers Roper dryers Admiral dryers Estate dryers Crosley dryers Inglis dryers Magic Chef dryers Note: This kit is designed for 29-inch large-capacity Whirlpool-family dryers. If your dryer is a compact or stackable model, verify compatibility with our support team before ordering. Key Features Three-part kit addresses the most common drum drive failures in a single repair — saves time and cost vs. replacing parts individually Belt: 92-1/4" x 1/4", 4 ribs, 3 grooves — premium neoprene rubber resists cracking, heat, and stretching Idler pulley: sturdy plastic with metal shaft and self-lubricating bearing — maintains correct belt tension Drum rollers: 2 included — reinforced self-lubricating metal bearings and thickened rubber wheels for quiet, stable drum support All hardware included: 4 tri-rings and 2 retaining washers — everything needed for complete installation Since the dryer must be disassembled to access any one of these parts, replacing all three at once eliminates repeated teardowns Compatible with 11 major appliance brands on the Whirlpool 29-inch platform Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 45–60 minutes with basic hand tools Product Specifications Kit Part Number 4392065 Condition Aftermarket Replacement Application 29-inch Gas and Electric Dryers Kit Includes 1x 341241 Drum Belt, 1x 691366 Idler Pulley, 2x 349241T Drum Rollers, 4x Tri-rings, 2x Retaining Washers Belt Length 92-1/4 inches Belt Width 1/4 inch Belt Ribs 4 ribs, 3 grooves Belt Material Neoprene rubber Idler Pulley Material Plastic / Metal Drum Roller Quantity 2 rollers (replace both at same time) Roller Lubrication Self-lubricating bearings — no grease needed Compatible Brands Whirlpool, Kenmore, Maytag, Amana, KitchenAid, Roper, Admiral, Estate, Crosley, Inglis, Magic Chef Installation Notes ⚠️ Unplug Dryer Before Starting Disconnect power (and shut off gas for gas dryers) before beginning. Remove the lint screen and unscrew the Phillips screws inside the lint screen housing. Use a putty knife to release the top panel clips and lift the top panel. Remove the front panel to access the drum. Release belt tension at the idler pulley, then lift the drum out. Remove the old belt, idler pulley, and drum rollers. Install the 2 new 349241T rollers onto the rear bulkhead shafts, pressing the new tri-rings and washers into place. Install the new 691366 idler pulley onto the idler arm. Loop the new 341241 belt around the drum with the ribbed side facing inward, then route it around the idler pulley and motor pulley. Reinstall the drum, reassemble the front and top panels, and restore power. Run a test cycle to confirm quiet operation. Tools needed: Phillips screwdriver, 1/4" nut driver, putty knife, needle-nose pliers, flat pry tool. Frequently Asked Questions Why should I replace all three parts at the same time? The drum belt, idler pulley, and drum support rollers all work together as a system and wear at similar rates under the same conditions. Since the dryer must be fully disassembled to access any one of these parts, replacing all three in a single repair is far more cost-effective than replacing them one at a time — which would require three separate teardowns. This is the same reason the 4392065 maintenance kit was designed: one repair, all three parts, done. What does each part in this kit do? The 341241 drum belt wraps around the outside of the drum and connects to the idler pulley and motor pulley — the motor drives the belt, which spins the drum. The 691366 idler pulley maintains tension on the belt so it grips the drum and motor pulley properly. The 349241T drum rollers are support wheels mounted on the rear of the dryer that cradle and support the back edge of the drum as it rotates. All three are essential to smooth, quiet drum operation. How is this kit different from the 4392067 repair kit? The 4392065 and 4392067 kits are designed for different Whirlpool-family dryer generations. The 4392065 uses the 341241 belt (92-1/4" x 1/4", 4 ribs) and the 691366 idler pulley, and is for older 29-inch Whirlpool-family dryers. The 4392067 uses the 661570V belt (93-1/2" x 1/4", 4 ribs) and the W10837240 idler arm assembly, and is for newer Whirlpool-family dryers (those with the lint screen inside the door). Use your model number to confirm which kit fits your specific dryer before ordering. Do I need to lubricate the drum rollers after installing? No — the 349241T drum rollers include self-lubricating bearings and do not require any additional grease or oil after installation. Applying grease to self-lubricating rollers is not recommended and can actually attract lint and debris, causing the rollers to wear faster. Is this an OEM or aftermarket kit? This is an aftermarket replacement kit built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM kit, but all three included components are manufactured from premium neoprene rubber, durable plastic, and metal to match the dimensions and performance of the original 4392065 kit parts. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 280148 Dryer Thermostat Set The XPARTCO 280148 is an aftermarket replacement thermal fuse and high-limit thermostat set for Whirlpool electric dryers, and also fits select Kenmore, Maytag, Amana, Roper, Estate, Crosley, Admiral, KitchenAid, and Norge models. This set bundles the 8557403 high-limit thermostat, which monitors temperature and automatically cuts power to the heating element if it overheats, then resets itself once the dryer cools, together with the 8318314 thermal fuse, a one-time backup safety device that permanently opens the circuit if temperatures climb high enough that the thermostat alone doesn't prevent an overheat. These two parts are sold together and commonly fail around the same time, since they protect the same circuit and respond to the same underlying overheating conditions — most often restricted exhaust venting. Symptoms include the dryer not heating at all, taking longer than normal to dry a load, or overheating before shutting down. It directly replaces 280148VP, 1175772, AP3874047, PS991443, EAP991443, and 314634. Quick Answer The XPARTCO 280148 Dryer Thermostat Set fixes Whirlpool, Kenmore, Maytag, Amana, Roper, Estate, Crosley, Admiral, KitchenAid, and Norge electric dryers with no heat, drying that takes too long, or a dryer that overheats before shutting down. Includes the 8557403 high-limit thermostat (auto-resetting) and 8318314 thermal fuse (one-time). Replaces 280148VP, 1175772, AP3874047, PS991443, EAP991443, 314634. Always inspect and clean the exhaust venting when replacing this set — a blown thermal fuse is a symptom of restricted airflow, and skipping the vent check leads to repeat failures. What's In The Set Component Type Function 8557403 High-Limit Thermostat Auto-resetting Cuts power to the heating element if temperature exceeds safe limits, resets automatically once the dryer cools. 8318314 Thermal Fuse One-time, non-resettable Backup safety device — permanently opens the circuit if temperature exceeds safe limits. Must be replaced once blown. Common Problems This Set Fixes Dryer runs but produces no heat at all Dryer won't start at all — no lights, no tumble, no response Drying takes noticeably longer than it used to Dryer overheating before shutting down Dryer that stopped working suddenly after running unusually hot Repeated thermal fuse failures on a dryer with a known venting issue Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer thermostat set directly replaces the following OEM and cross-reference part numbers: 280148, 1175772, 280148VP, PD00002627, FIX991443, EAP991443, AH991443, AP3874047, AWP39427, EA991443, PS991443, 8318314, WP8557403, 8557403, 1180102, AP6013164, AWP48681, PD00003588, PS11746386 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This thermostat set is compatible with select Whirlpool electric dryers, and also fits select Kenmore, Maytag, Amana, Roper, Estate, Crosley, Admiral, KitchenAid, and Norge dryers built on the Whirlpool platform, including model numbers such as: 7MWED5620HW0, 7MWED5620HW1, 7MWED6613HC0, 7MWED6613HC1, 7MWED6613HW0, 7MWED6613HW1 MED5500FC1, MED5500FC2, MED5500FW1, MED5500FW2 MED5630HC0, MED5630HC1, MED5630HC2, MED5630HW0, MED5630HW1, MED5630HW2 MED6000XG0, MED6000XG1, MED6000XG2, MED6000XR0, MED6000XR1, MED6000XW0, MED6000XW1, MED6000XW2 MED6630HC0, MED6630HC1, MED6630HC2, MED6630HW0, MED6630HW1, MED6630HW2 MED7000XG0, MED7000XG1, MED7000XR0, MED7000XR1, MED7000XW0, MED7000XW1, MED7000XW2 MED7230HC0, MED7230HC1, MED7230HC2, MED7230HC3, MED7230HW0, MED7230HW1, MED7230HW2, MED7230HW3 MED8200FC1, MED8200FC2, MED8200FW1, MED8200FW2 Note: Always verify your full model number before ordering, since Whirlpool uses several different thermostat and fuse designs across its dryer lineup. This set is commonly purchased alongside heating element WP8544771. Contact our support team with your model number if you're unsure. Key Features 2-piece set: 8557403 auto-resetting high-limit thermostat and 8318314 one-time thermal fuse Resolves "no heat," "won't start at all," "takes too long to dry," and "overheating" symptoms Addresses two overheat-protection thresholds in the same circuit at once Commonly purchased alongside heating element WP8544771 No special tools required for installation Replaces 280148VP, 1175772, AP3874047, PS991443, EAP991443, and 314634 Compatible with Whirlpool, Kenmore, Maytag, Amana, Roper, Estate, Crosley, Admiral, KitchenAid, and Norge electric dryers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Set Part Number 280148 OEM Part Number 280148 Set Contents 1x High-Limit Thermostat (8557403), 1x Thermal Fuse (8318314) Condition Aftermarket Replacement Application Whirlpool Electric Dryers High-Limit Thermostat Type Automatically resetting Thermal Fuse Type One-time use, non-resettable Companion Heating Element WP8544771 (commonly used together) Repair Difficulty Easy to Moderate — no special tools required Compatible Brands Whirlpool, Kenmore, Maytag, Amana, Roper, Estate, Crosley, Admiral, KitchenAid, Norge Installation Notes ⚠️ Unplug Dryer Before Starting — Inspect And Clean The Venting Before Reassembling Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Access is typically through the rear panel, near the heating element and blower housing where both components are mounted. Photograph the wiring connections before disconnecting anything, since the thermostat and fuse can be easy to swap positions by mistake. Remove each old component from its mounting position, noting orientation, and disconnect its wiring. Before reassembling, fully inspect and clean the dryer's exhaust vent, from the lint trap housing all the way to the exterior vent hood, checking for lint buildup, crushed sections, or excessive length. Restricted airflow is the leading cause of failure for both of these components, and skipping the vent check often leads to repeat failures even with new parts installed. Install the new 8557403 thermostat and 8318314 thermal fuse from this set in the same positions as the parts they replace, reconnecting wiring exactly as photographed. Reassemble the panel, restore power, and run a full test cycle to confirm normal, consistent heating with no premature shutoffs. Tools needed: Phillips or nut driver (model-dependent), work gloves. Frequently Asked Questions Why replace both the thermostat and the fuse together instead of just the one that failed? These two parts protect the same circuit at different thresholds and tend to fail from the same underlying cause. If the high-limit thermostat isn't regulating temperature correctly, the thermal fuse often ends up blowing as the backup safety measure. Replacing only one risks the other failing again shortly after, so they're sold and serviced together as a set. I replaced this set and the dryer failed again. What should I check? This is a strong sign the underlying cause — almost always restricted airflow — was never addressed. Thoroughly inspect and clean the entire exhaust path from the lint trap housing to the outside vent hood, checking for lint buildup, crushed or kinked ductwork, or a vent run that's too long. Failing to correct a venting issue will cause repetitive failures of this set even when it's brand new. Should I replace the heating element at the same time? It's worth considering if your dryer's heating element (commonly WP8544771 on compatible models) is original and has been running alongside a failing thermostat, since sustained overheating can stress the element as well. It's not required, but since you'll already have the panel open for this repair, it's a reasonable time to inspect the element for visible damage. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the temperature thresholds and mounting configuration of the original 280148 high-limit thermostat and thermal fuse set used in compatible Whirlpool, Kenmore, Maytag, Amana, Roper, and related electric dryers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less

EXP694 Dryer Repair Kit Replaces DC97-16782A, 6602-001655, DC93-00634A The EXP694 Dryer Repair Kit is a complete drum system rebuild solution designed to restore smooth, quiet, and efficient dryer operation. This kit includes the most common wear components found inside your dryer: drum belt, idler pulley, and drum support rollers. Over time, these parts wear down together, causing squeaking, grinding, drum slippage, or complete failure to spin. Replacing all components at once ensures proper alignment, eliminates noise, and prevents repeat breakdowns — making this the most effective long-term repair solution. Quick Answer The EXP694 Dryer Repair Kit fixes dryers that won’t spin, make loud squeaking or grinding noises, or stop tumbling. It replaces the belt, rollers, and idler pulley to restore smooth and quiet drum operation. Note: Includes four rollers (each with shaft and two tri-rings), one idler pulley, and one belt. Replace all four rollers for even wear. Inspect the drum and felt seal (e.g., DC97-07618A) for wear. Clean lint from the drum and cabinet to prevent overheating. Common Problems This Part Fixes Dryer drum not spinning or slipping Loud squeaking, grinding, or thumping noises Uneven or slow drum rotation Dryer stopping mid-cycle Excessive vibration or instability Worn belt, rollers, or idler pulley components Replaces Part Numbers This repair kit replaces the following common drum system components: Drum Roller: DC97-16782A, AP5325135, DC97-16782C, DC97-16782D, 2027851, DC97-07523A, DC97-07523B, PS4221885, WPW10177428, AP6016361, W10177428, 35001136, DC97-07523A, PS11749648 Idler Pulley: DC93-00634A, AP6038887, DC96-00882C, DC61-01230B, DC96-00882B, PS11771601, 12002777, AP4010261, 1401171, 35001083, 35001098, 35001276, AH2004052, DC61-01215A, DC96-00882B, EA2004052, PS2004052 Drum Belt: 6602-001655, AP4373659, 1935594, 6602-001314, PS4133825, WPW10205415, AP6017004, W10205415, 35001137, 6602-001314, PS11750299 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This repair kit is compatible with select dryers from the following brands: Samsung dryers (gas and electric models) Kenmore / Sears dryers (select models built on Samsung platform) Always verify your appliance model number before ordering. Contact our support team if you're unsure. Key Features Complete drum repair kit including belt, rollers, and idler pulley OEM-equivalent fit, performance, and durability Eliminates noise and restores smooth drum rotation Prevents repeat repairs by replacing all wear components together Cost-effective all-in-one repair solution DIY-friendly installation with basic tools Product Specifications Includes 4 drum rollers (DC97-16782A, ~3-1/4" diameter x 1-1/8" width, blue/black plastic/rubber, metal shaft, self-lubricating bushing with ball bearing, each with shaft and two tri-rings), 1 idler pulley (DC93-00634A, metal/plastic), 1 drum belt (6602-001655, 92" long, 5 ribs, neoprene), kit dimensions ~10"L x 6"W x 4"H. Part Type Dryer Repair Kit Includes Belt, Rollers, Idler Pulley Application Dryer Drum System Condition Aftermarket Replacement Compatible Brands Samsung, Kenmore Installation Notes ⚠️ Safety First — Unplug Dryer Before Starting Disconnect power before servicing. Remove dryer panels, release belt tension, and replace worn components. Ensure proper alignment of the belt and rollers before reassembly. For best results, replace all components included in this kit at the same time. Frequently Asked Questions Should I replace all parts at once? Yes. The belt, rollers, and pulley wear together. Replacing all components ensures smooth operation and prevents future breakdowns. Will this fix dryer noise? Yes. This kit resolves most squeaking, grinding, and thumping noises caused by worn drum components. Is this an OEM part? This is a high-quality aftermarket repair kit built to OEM-equivalent standards for performance and durability. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 3406107 Dryer Door Switch Replaces WP3406107 The XPARTCO 3406107 is an aftermarket replacement door switch for Whirlpool, Kenmore, Maytag, and KitchenAid dryers. Mounted inside the upper corner of the front panel, this safety switch has a spring-loaded black tab that gets pressed in when the door closes. That contact tells the control board the door is shut, which is required before the dryer will start, and it also powers the interior drum light. Over time the switch's internal contacts wear out or the tab loses spring tension, and the dryer either won't start at all or runs with the door open — a safety condition the switch is specifically designed to prevent. This is a three-wire SPDT (single pole, double throw) switch built to the same dimensions and mounting points as the original, and it's designed to remain compatible with older two-wire harnesses as well. Direct-fit aftermarket replacement, no wiring modifications needed. Quick Answer The XPARTCO 3406107 Dryer Door Switch fixes a dryer that won't start, runs with the door open, or has a dead interior light. Direct-fit replacement for OEM WP3406107. Classic symptom: pressing start does nothing until you push and hold the door shut, or the drum light never comes on. Common Problems This Part Fixes Dryer won't start even though the door is closed Dryer runs with the door open (safety switch failure) Interior drum light doesn't turn on Door doesn't seem to latch or seal properly against the switch tab Drum doesn't spin, or cycle stops intermittently Touchpad or start button appears unresponsive Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This door switch directly replaces the following part numbers: WP3406107, WPW10569603, 3406107, 3406109, W10569603, 3405100, 3405101, 3406100, 3406101, ES6107, 528948, 11259-65, PD00002378, EAP11741701, AP6008561, AWP47183, PS11741701 This switch design was updated to a three-wire configuration at some point in its production history (superseding older 3405100/3405101/3406100/3406101 numbers), but the current three-wire version remains compatible with older two-wire harnesses, so it's a safe direct replacement across all of these part numbers. Compatibility This door switch is compatible with a wide range of Whirlpool, Kenmore, Maytag, and KitchenAid dryers, including units across the: Whirlpool/Kenmore Series 60, 70, 80, 90, 500, 600, 700, and 800 dryer lines AED4475TQ1, MEDC400VW0, and numerous additional model numbers Note: This switch has been used across a very wide range of Whirlpool-built dryers (including Kenmore, Maytag, and KitchenAid badged units) spanning many production years, so the list above is only a sample. Confirm your model number against your dryer's parts diagram, or contact our support team to verify fit before ordering. Key Features Direct-fit aftermarket door safety switch for Whirlpool-built dryers Three-wire SPDT design, backward-compatible with two-wire harnesses Controls both the start-permission safety interlock and the interior drum light Resolves no-start, runs-with-door-open, and dead-light symptoms White plastic and metal tab construction, approx. 6.5" length Straightforward swap — typically 15–30 minutes with basic hand tools Product Specifications Part Number 3406107 OEM Part Number WP3406107 Part Type Dryer Door Safety Switch Condition Aftermarket Replacement Switch Type SPDT (Single Pole, Double Throw) Wire Configuration Three-Wire (Backward-Compatible with Two-Wire Harnesses) Length Approx. 6.5 Inches Color / Material White; Plastic & Metal Construction Application Whirlpool, Kenmore, Maytag & KitchenAid Dryers Installation Notes ⚠️ Unplug Power Before Installing Unplug the dryer or switch off its circuit breaker before beginning. The switch is mounted inside the upper corner of the front panel, so you'll need to remove the front panel or top panel per your model's service guide to access it. Disconnect the wire connector from the old switch, then remove the mounting screw(s) holding it in place. Install the new switch in the same position, reconnect the wire connector, and reinstall the panel. Before closing everything up, you can test the switch by pressing the black tab — you should feel spring resistance and hear or feel a distinct click. Restore power and confirm the dryer starts normally with the door closed and stops when the door is opened. Frequently Asked Questions My dryer won't start — is this the part I need? This is one of the most common causes of a dryer that won't start even with the door closed. Try pressing the black tab on the switch by hand — if it feels loose, doesn't click, or offers no resistance, the switch has likely failed and needs replacement. My dryer runs even with the door open — is that dangerous? Yes, this indicates the door safety switch has failed in a way that no longer prevents operation with the door open, which is a safety hazard. Replace the switch promptly and avoid running the dryer with the door open in the meantime. My dryer has a two-wire connector — will this three-wire switch still work? Yes. This switch was redesigned to a three-wire configuration but remains compatible with older two-wire wiring harnesses, so it's a safe direct replacement regardless of which wire configuration your dryer currently has. Does this switch also control the interior light? Yes. This switch serves a dual function — it's the safety interlock that permits the dryer to run only with the door closed, and it also powers the interior drum light when the door is open. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO W10198086 Dryer Drum Belt Replaces WPW10198086 The XPARTCO W10198086 is an aftermarket replacement dryer drum belt for Whirlpool, Maytag, and Amana electric dryers. This belt wraps around the drum and the motor pulley, and it's what actually makes the drum turn — the motor drives the belt, and the belt tumbles the drum. When this belt breaks or wears out, the motor can still run, but nothing inside the dryer actually moves. This is a 5-rib belt measuring approximately 92-1/2"L x 5/16"W x 1/8"H, with grooves on one side and a flat surface on the other. A broken or badly worn belt produces an unmistakable symptom: the dryer runs — you'll hear the motor and often the blower — but the drum doesn't turn at all, or turns only briefly before stopping. A simple way to confirm this diagnosis before opening the dryer is to try turning the drum by hand; if it spins freely with no resistance, the belt is almost certainly broken. Overloading the dryer with oversized loads is a common cause of belt failure over time. It directly replaces WPW10198086, W11575709, W11667279, LB8086, 1481904, AP6016842, AH2348726, EA2348726, PS2348726, EAP11750135, PS11750135, AWP49253, and PD00007598. Quick Answer The XPARTCO W10198086 Dryer Drum Belt fixes Whirlpool, Maytag, and Amana electric dryers where the motor runs but the drum doesn't turn, or turns only briefly. 5-rib belt, approximately 92-1/2"L x 5/16"W x 1/8"H. Replaces WPW10198086, W11575709, W11667279, LB8086, 1481904, AP6016842, AH2348726, EA2348726, PS2348726, EAP11750135, PS11750135, AWP49253, PD00007598. Try turning the drum by hand first — if it spins freely with no resistance, the belt has broken. Common Problems This Part Fixes Dryer runs — motor and blower audible — but the drum doesn't turn Drum turns briefly then stops Drum spins freely by hand with no resistance (indicating a broken belt) Loud squeaking noise during operation from a worn but not yet broken belt Burning rubber smell from a slipping or overheating belt Dryer that stopped tumbling suddenly during a cycle Cross Reference Information Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item. Replaces Part Numbers This dryer drum belt directly replaces the following OEM and cross-reference part numbers: WPW10198086, W10198086, 1481904, W11575709, W11667279, LB8086, PD00007598, EAP11750135, AP6016842, AWP49253, PS11750135 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drum belt is compatible with select Whirlpool electric dryers, and also fits select Maytag and Amana dryers built on the same platform, including model numbers such as: MEDC465HW0, MEDC215EW0, MEDC215EW1, MEDC200XW0, MEDC200XW1, MEDC200XW3 MEDX655DW0, MEDX655DW1, MEDX500BW0, MEDX500BW1 MEDC300BW0, MEDC300XW0, MEDC300XW1, MEDC400VW0, MEDC400BW1, MEDC415EW0 MGDC400VW0, MGDC215EW0, MGDC215EW2, MGDC465HW0, MGDC300XW3, MGDC400BW1, MGDC400BW2, MGDC500VW0, MGDC555DW1 MEDC555DW1, MEDC555DW2, MEDC100YQ0, MEDB766FW0 7MMGDC400DW0, 7MMGDC400DW1, 7MMGDC400DW2, 7MMEDC300DW1, 7MMEDC300BW0 Note: Always verify your full model number before ordering, since Whirlpool uses several different drum belts across its dryer lineup with different lengths and rib counts. Contact our support team with your model number if you're unsure. Key Features Aftermarket replacement drum belt — connects the motor pulley to the drum so it can turn Resolves "motor runs but drum won't turn," "drum stops mid-cycle," and "squeaking" symptoms caused by a worn or broken belt 5-rib design with grooves on one side, flat on the other Approximately 92-1/2"L x 5/16"W x 1/8"H Direct drop-in replacement matching the original belt routing Replaces WPW10198086, W11575709, W11667279, LB8086, 1481904, AP6016842, AH2348726, EA2348726, PS2348726, EAP11750135, PS11750135, AWP49253, and PD00007598 Compatible with Whirlpool, Maytag, and Amana electric dryers Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number W10198086 OEM Part Number WPW10198086 Part Type Dryer Drum Belt Condition Aftermarket Replacement Length Approx. 92-1/2 in. Width 5/16 in. Thickness 1/8 in. Ribs 5 Color Black Material Rubber Repair Difficulty Easy — 15 to 30 minutes Quantity 1 drum belt Compatible Brands Whirlpool, Maytag, Amana Installation Notes ⚠️ Unplug Dryer Before Starting — Check The Idler Pulley While You're In There Disconnect power at the outlet or shut off the circuit breaker before beginning. Wear work gloves. Lift the lint screen cover and remove the two screws underneath it — if your model has a lint screen with a built-in cover, simply pull it out and remove the screws. Run a putty knife around the top edge of the dryer to find the release clips, then press them in to release and swing the top open. Remove the front panel to access the drum and belt area; on many models, all the work for this repair is performed from the front rather than the rear. Route the new W10198086 belt around the drum with the grooved side against the drum, then loop it around the motor pulley and the idler pulley, following the routing diagram on the inside of the cabinet or your old belt's path if it's still intact when you remove it. If the belt broke rather than just wearing out, check that the idler pulley is still properly seated — a belt snapping can sometimes cause the pulley to pop out of position, and reseating it is a quick fix while you already have the panel open. Reinstall the front panel, close the top and secure the release clips, and reinstall the lint screen area and its screws. Restore power and run a test cycle to confirm the drum turns smoothly with no slipping or noise. Tools needed: Phillips screwdriver, 5/16" nut driver, putty knife, work gloves. Frequently Asked Questions My dryer runs but the drum won't turn. How do I confirm it's the belt before ordering? Try turning the drum by hand with the dryer unplugged. If it spins freely with little to no resistance, that's a strong sign the belt has broken, since an intact belt normally provides some resistance from the motor and idler pulley connected to it. If the drum feels stuck or hard to turn instead, the problem may be elsewhere, such as a seized idler pulley or motor issue. What caused my belt to break in the first place? Belts wear out from age and normal use, but overloading the dryer with oversized or overly heavy loads is a common accelerating factor, since it puts extra strain on the belt with every rotation. Avoiding overloaded loads going forward can help the new belt last as long as it should. While replacing the belt, I noticed the idler pulley looks out of place. Is that related? Yes, this can happen when a belt breaks suddenly — the pulley can pop out of its normal seated position as tension is lost. Since you'll already have the panel open for the belt replacement, take a moment to check that the idler pulley is properly seated before closing everything back up, as this is a common and easy thing to overlook. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the length, width, rib count, and routing configuration of the original WPW10198086 drum belt used in compatible Whirlpool, Maytag, and Amana electric dryers. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Quality Aftermarket Parts ✓ Fast US Shipping ✓ Compatibility Support ✓ Secure Checkout

Read more less