Washer Parts

XPARTCO DC97-16350U Washer Suspension Rod Kit (Set of 4) The XPARTCO DC97-16350U is an aftermarket replacement washer suspension rod kit (set of 4) compatible with a wide range of Samsung top-load washers in the WA40, WA41, WA42, WA44, WA45, WA49, and WA50 series. The suspension rods are spring-loaded shock-absorbing rods that connect the outer washer tub to the top corners of the cabinet frame, suspending the tub and dampening the vibrations generated during agitation and high-speed spin cycles. When one or more rods lose tension, break, or degrade, the tub swings off-center and strikes the cabinet walls — causing violent shaking, loud banging, error code dc (out of balance), UE imbalance errors, and progressive damage to the machine. Each rod measures 26.4–26.5 inches in overall length and 1-1/4 inches in diameter, constructed from spring steel with plastic end caps. The kit includes all 4 suspension rods — always replace all four at the same time since they wear at the same rate. It directly replaces DC97-16350S, DC97-16350T, DC97-16350E, DC97-16350C, DC97-16350D, DC97-16350K, DC97-05280W, 4962798, AP6884450, EAP12720841, PS12720841, and PD00065434. Wear gloves during installation — the rods are coated with grease. Installs in 20–30 minutes — no special tools required. Quick Answer The XPARTCO DC97-16350U Washer Suspension Rod Kit fixes Samsung top-load washers that vibrate violently, bang loudly, walk across the floor, or display dc or UE imbalance error codes during spin. Set of 4 rods, 26.4–26.5" long, 1-1/4" diameter, spring steel with plastic end caps. Replace all 4 at the same time. Wear gloves — rods are greased. Compatible with Samsung WA40–WA50 series. Replaces DC97-16350S, DC97-16350T, DC97-16350E, DC97-16350C, DC97-16350D, AP6884450, PS12720841. Common Problems This Kit Fixes Washer vibrating violently or shaking excessively during the spin cycle Loud banging or thumping — tub striking the cabinet walls during spin Washer "walking" or moving across the floor during high-speed spin Error code dc displayed — Samsung out-of-balance error during spin Error code UE displayed — unbalanced load error the washer cannot self-correct Washer repeatedly stopping and rebalancing the load without completing the spin cycle Visible broken, detached, or sagging suspension rod inside the washer cabinet Rattling or clunking during agitation — tub no longer centered Replaces Part Numbers This suspension rod kit directly replaces the following OEM and cross-reference part numbers: DC97-16350U, DC97-16350S, DC97-16350T, DC97-16350E, DC97-16350C, DC97-16350D, DC97-16350J, DC97-16350K, DC97-16350U, DC97-16350E, DC97-16350S, DC97-16350C, DC97-16350D, DC97-16350T, AP6884450, ASM34747, EAP12720841, PD00065434, PS12720841. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This suspension rod kit is compatible with select top-load washers from the following Samsung series: Samsung WA40 series — WA400PJHDWR, WA40J3000AW, WA40A3005AW, WA44A3205AW and related models Samsung WA41 series — WA41A3000AW and related models Samsung WA42 series — WA422PRHDWR and related models Samsung WA45 series — WA45H7000AW, WA45H7200AW, WA45K7600AW, WA45M7050AW, WA45N3050AW, WA45T3200AW, WA45T3400AW, WA45T3400AP, WA456DRHDSU, WA456DRHDWR and related models Samsung WA49 series — WA49B5105AW, WA49B5205AW and related models Samsung WA50 series — WA50R5200AW, WA50R5400AV, WA50R5400AW, WA50T5300AC and related models Kenmore / Sears top-load washers (select Samsung-built models) Important: The DC97-16350U rod is 26.4–26.5 inches long and is for Samsung WA40–WA50 series washers. Larger-capacity WA48–WA54 series models use the longer DC97-16350V rod (27.5 inches). Always measure your existing rods or verify your model number before ordering — using the wrong length rod can cause the tub to sit at the incorrect height inside the cabinet. Key Features Set of 4 suspension rods — complete replacement covering all four tub mounting points Suspends and centers the outer tub within the cabinet — dampens agitation and spin vibration to prevent tub-to-cabinet contact Resolves Samsung error codes dc (out of balance) and UE (unbalanced load) Rod length: 26.4–26.5 inches overall; diameter: 1-1/4 inches Spring steel construction with plastic end caps — durable and corrosion resistant Rods are pre-coated with grease — wear work gloves during installation Replace all 4 rods at the same time — rods wear together and partial replacement results in uneven tub support No special tools required — installs in 20–30 minutes Replaces DC97-16350S, DC97-16350T, DC97-16350E, DC97-16350C, DC97-16350D, and over 15 additional cross-references Aftermarket replacement built to OEM-equivalent quality standards Product Specifications Part Number DC97-16350U Part Type Washer Suspension Rod and Spring Assembly Condition Aftermarket Replacement Application Samsung Top-Load Washers — WA40, WA41, WA42, WA44, WA45, WA49, WA50 series Quantity Set of 4 (replace all four rods at the same time) Rod Length 26.4–26.5 inches overall Rod Diameter 1-1/4 inches Material Spring steel / Plastic end caps Color Brass / Black / White / Pink Lubrication Pre-coated with grease — wear gloves during installation Error Codes Resolved dc (out of balance), UE (unbalanced load) Compatible Brands Samsung, Kenmore (Samsung-built) Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting — Wear Gloves Disconnect power and turn off the water supply before beginning. Wear work gloves throughout — the suspension rods are coated with grease. Remove the lid and the top panel (typically secured by screws under the lid hinge covers and at the rear corners). With the top panel removed, the four suspension rods are visible at the corners, each running from a mounting point on the tub rim up to a hook or bracket at the top corners of the cabinet frame. Note the orientation and attachment method of each rod before removing. Unhook the top of each rod from the cabinet bracket and lift the bottom cup off the tub mounting pin. Install each new DC97-16350U rod by seating the bottom cup onto the tub mounting pin and hooking the top over the cabinet bracket. Replace all four rods before reassembling. Reinstall the top panel and lid, restore power and water, and run a spin cycle to verify smooth, quiet, centered operation. Tools needed: Phillips screwdriver; no special tools required for the rods themselves. Frequently Asked Questions What is the difference between DC97-16350U and DC97-16350V? Both are Samsung top-load washer suspension rods, but they are different lengths for different washer capacity generations. The DC97-16350U is approximately 26.4–26.5 inches long and is used on mid-capacity Samsung WA40 through WA50 series washers. The DC97-16350V is approximately 27.5 inches long and is used on larger-capacity WA48 through WA54 series washers. Using the wrong length rod causes the tub to sit at the wrong height inside the cabinet, which can cause new imbalance issues. Always measure your existing rods or verify your model number before ordering. Why must I replace all 4 rods instead of just the broken one? All four suspension rods experience the same amount of wear over the same number of wash cycles. When one rod fails, the remaining three have experienced the same stress and fatigue and are likely to fail soon after. Replacing only the broken rod leaves three worn rods supporting the tub unevenly — this can cause continued vibration, accelerate wear on the new rod, and require a second repair shortly after. Replacing all four at the same time ensures even tub support, fully resolves the imbalance, and prevents a repeat repair. Do DC97-16350S, DC97-16350T, and DC97-16350E all cross to the DC97-16350U? Yes — DC97-16350S, DC97-16350T, DC97-16350E, DC97-16350C, and DC97-16350D are all cross-reference part numbers for the same Samsung suspension rod assembly used across different production runs of the same washer series. Samsung updates part number suffixes during production revisions. All of these numbers have the same 26.4–26.5" length and are interchangeable with the DC97-16350U. What do error codes dc and UE mean on Samsung washers? Error code dc on Samsung top-load washers indicates the machine has detected an out-of-balance condition and stopped spinning to prevent damage. Error code UE indicates an unbalanced load that the washer cannot self-correct by redistributing. Both codes can be caused by an overloaded or unevenly distributed laundry load — but if the errors occur consistently even with normal, balanced loads, worn or broken suspension rods are the most common mechanical cause. Replacing the rod kit resolves these errors in most cases. Is this an OEM or aftermarket part? This is an aftermarket replacement kit built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured from spring steel with plastic end caps to match the length and spring tension of the original DC97-16350U suspension rods. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 4681EA2001T Washer Drain Pump Motor The XPARTCO 4681EA2001T is an aftermarket replacement drain pump motor assembly compatible with a wide range of LG and Kenmore front-load washers. The drain pump motor forces water out of the washer drum through the drain hose during and after the wash and spin cycles — when it fails, the washer will not drain, will display an OE error code, leave standing water in the drum, or produce a loud humming or grinding noise during the drain phase. This drain pump motor is rated at 120V–127V, 60Hz, 85W, 1.4A with a flow rate of 45 liters per minute and a spin speed of 1,100–1,200 RPM. It is made from durable metal and ABS plastic and includes the pump impeller and a removable filter housing with sealing ring for quieter, smoother operation. Note: this is the motor assembly only — it reuses the existing pump housing from your washer. It directly replaces 4681EA2001N, 4681EA1007G, 4681EA1007D, AP5328388, and several additional cross-reference numbers. Installs in 30–60 minutes with basic hand tools. Quick Answer The XPARTCO 4681EA2001T Washer Drain Pump Motor fixes LG and Kenmore front-load washers showing OE error codes, not draining, leaving standing water, or making loud humming or grinding sounds during the drain cycle. Rated 120V–127V/60Hz/85W/1.4A, 45L/min, 1,100–1,200 RPM. Includes impeller and removable filter housing. Motor assembly only — reuses existing pump housing. Replaces 4681EA2001N, AP5328388, 4681EA1007G, and more. Common Problems This Part Fixes OE error code displayed — washer cannot drain within the allotted time Washer not draining — standing water remaining in the drum after a cycle Loud humming or buzzing during the drain cycle — motor running but impeller not turning Grinding or rattling noise during draining — physical damage to pump components Washer stopping mid-cycle due to a drain fault Washer draining very slowly — worn pump motor below rated flow Water leaking from the drain pump area Replaces Part Numbers This drain pump motor directly replaces the following OEM and cross-reference part numbers: 4681EA2001T, 4681EA1007G, 2003273, 4681EA1007D, 4681EA2001D, 4681EA2001N, 4681EA2001U, DP040-038, ALG51292, AH3579318, EA3579318, PD00001722, EAP3579318, AP5328388, PS3579318. 4681EA2001T is the current updated part number — it is the manufacturer-approved replacement for the older 4681EA2001N. If your washer or parts diagram shows 4681EA2001N, order 4681EA2001T. Compatibility This drain pump motor is compatible with select front-load washers from the following brands: LG front-load washers — WM2xxx, WM3xxx, WM4xxx, WM5xxx, WM8xxx, WM9xxx series Kenmore / Sears front-load washers (select LG-built models, including 796-series) Important: This is the pump motor assembly only — it installs into your washer's existing pump housing. The pump housing is not included and is reused from your old assembly. Always verify your model number before ordering. Contact our support team if you're unsure. Key Features Forces water out of the drum through the drain hose during wash and spin cycles at 45 liters per minute Rated 120V–127V, 60Hz, 85W, 1.4A — correct electrical specifications for compatible LG and Kenmore models Spin speed: 1,100–1,200 RPM for powerful, efficient drainage Includes pump impeller and removable filter housing with sealing ring Removable filter housing allows easy cleaning without full pump disassembly Sealing ring reduces vibration and noise during operation Durable metal and ABS plastic construction — built to withstand repeated high-volume drainage cycles Motor assembly only — installs into existing pump housing, no housing replacement needed Resolves OE error code on compatible LG and Kenmore front-load washers Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 30–60 minutes with basic hand tools Product Specifications Part Number 4681EA2001T Also Replaces 4681EA2001N (updated current replacement) Part Type Washer Drain Pump Motor Assembly Condition Aftermarket Replacement Application LG and Kenmore Front-Load Washers Voltage 120V – 127V AC Frequency 60 Hz Wattage 85W Amperage 1.4A Flow Rate 45 liters per minute Spin Speed 1,100 – 1,200 RPM Material Metal / ABS Plastic Includes Motor assembly, impeller, removable filter housing, sealing ring Note Motor assembly only — existing pump housing is reused Compatible Brands LG, Kenmore Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off the water supply before beginning any repair. Place towels and a shallow pan at the front of the washer to catch residual water. Open the small access panel at the lower front of the washer and drain any remaining water through the drain hose or filter port. Remove the front panel of the washer by unscrewing the top panel screws, then removing the door gasket retaining wire and door latch screws to free the front panel. With the front panel removed, the drain pump assembly is now visible at the lower front. Use a flat-head screwdriver to release the pump mounting clip, then disconnect the drain hoses using pliers to loosen the clamps. Disconnect the wire harness from the pump motor. Pull the motor assembly out of the pump housing. Install the new 4681EA2001T motor into the existing housing, reconnect the hoses and wire harness, secure the pump clip, and reassemble the front panel. Restore power and water supply, then run a drain/spin cycle to verify proper drainage. Tools needed: Phillips screwdriver, flat-head screwdriver, needle-nose pliers, slip-joint pliers, shallow pan. Frequently Asked Questions What is the difference between 4681EA2001T and 4681EA2001N? These are the same drain pump motor — 4681EA2001T is the updated current part number that replaced the older 4681EA2001N. LG issued the updated number during a production cycle revision. If your washer or its documentation shows 4681EA2001N, 4681EA2001D, or any other older variant, the 4681EA2001T is the correct replacement to order. What does the OE error code mean on an LG washer? OE (or OE error) stands for "Outlet Error" — it means the washer was unable to drain within the expected time. Common causes include a clogged drain filter, a blocked or kinked drain hose, or a failed drain pump motor. Before replacing the motor, check and clean the drain filter and inspect the drain hose for kinks or blockages. If both are clear and the washer still shows OE, the pump motor has likely failed and needs replacement. Does this include the pump housing? No — the 4681EA2001T is the motor assembly only. It installs into your washer's existing pump housing, which is not included and does not need to be replaced in most cases. If your pump housing is cracked or damaged, you will need to source it separately. In most repairs, the housing is reused and only the motor assembly is replaced. Should I check the drain filter before replacing the pump motor? Yes — always check and clean the drain filter first. LG front-load washers have a coin trap and filter at the lower front that should be cleaned regularly. A heavily clogged filter or a foreign object jammed in the impeller can cause OE errors and loud humming without the pump motor being permanently damaged. Remove the filter, clear debris from the impeller area, and test the washer. If the problem persists after cleaning, the motor is the likely culprit. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine LG OEM part, but is manufactured from durable metal and ABS plastic to match the electrical specifications and performance of the original 4681EA2001T drain pump motor assembly. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout  

Read more less

XPARTCO 285753A Washer Direct Drive Motor Coupler The XPARTCO 285753A is an aftermarket replacement direct drive motor coupler (also called a motor coupling or drive coupler) compatible with a wide range of Whirlpool-family top-load washers including Whirlpool, Kenmore, KitchenAid, Maytag, Amana, Roper, Admiral, Estate, Crosley, Inglis, and Magic Chef. The motor coupler connects the drive motor shaft to the transmission — transferring the motor's power to the transmission to drive the agitator and spin the drum during wash and spin cycles. It is a deliberate weak point in the drivetrain: if the washer is overloaded, the coupler breaks apart first, protecting the far more expensive motor and transmission from damage. This is the updated 285753A design with metal sleeves for added strength — it replaces all previous coupler styles and versions including the original 285753, 280152, 285743, and 285140. This kit includes 2 plastic coupling halves and 1 rubber isolation dampener. Dimensions approximately 2" L x 1-1/4" W x 2" H. Fits direct-drive top-load washers only — not compatible with belt-drive machines. Installs in 30–45 minutes with basic hand tools. Quick Answer The XPARTCO 285753A Washer Motor Coupler fixes top-load washers that fill and drain normally but will not agitate or spin. The motor coupler connects the motor to the transmission — when it breaks, the motor runs but neither the agitator nor the drum moves. Kit includes 2 plastic coupling halves and 1 rubber dampener. Updated design with metal sleeves. Replaces all previous coupler versions including 285753, 280152, 285743, 285140. Compatible with Whirlpool, Kenmore, KitchenAid, Maytag, Amana, Roper, Admiral, and more direct-drive top-load washers. Common Problems This Part Fixes Washer fills with water and drains but will not agitate or spin Motor runs (you can hear it) but agitator and drum do not move Washer spins slowly or incompletely — clothes still very wet after spin cycle Loud humming or buzzing from the motor area without agitation or spin Burning rubber or plastic smell during the wash or spin cycle Washer shakes excessively — broken coupler causing uneven power transfer Broken plastic or rubber pieces visible inside the bottom of the washer cabinet Replaces Part Numbers This motor coupler directly replaces the following OEM and cross-reference part numbers: 285753A, 1195967, 21003, 280152, 285140, 285743, 285753, 285753AVP, 3352470, 3363664, 3364002, 3364003, 62672, 62693, 661560, 80008, 8559748, AWP39583, PD00002353, AH1485646, EAP1485646, EA1485646, TJ285753, ER285753, AP3963893, PS1485646. The 285753A replaces all previous motor coupler styles and versions. If your parts diagram shows any of the older numbers above, the 285753A is the correct current replacement. Compatibility This motor coupler is compatible with select direct-drive top-load washers from the following brands: Whirlpool top-load washers (direct drive — no belt) Kenmore / Sears top-load washers — 70 series, 80 series, 90 series, and 110 series (Whirlpool-built) KitchenAid top-load washers Maytag top-load washers (direct drive models) Amana top-load washers Roper top-load washers Admiral top-load washers Estate top-load washers Crosley top-load washers Inglis top-load washers Magic Chef top-load washers Important: The 285753A is for direct-drive top-load washers only — machines where the motor connects directly to the transmission without a belt. It is not compatible with front-load washers or older belt-drive top-load washers. If you can see a drive belt inside your washer cabinet, this is not the correct part. Key Features Connects the drive motor shaft to the transmission — transfers motor power to drive the agitator and spin drum Intentional sacrificial part — designed to break before the motor or transmission during overload, saving far more expensive components Updated 285753A design with metal sleeves — stronger than original all-plastic versions; replaces all previous coupler styles Kit includes 2 plastic coupling halves and 1 rubber isolation dampener — complete assembly Dimensions: approximately 2" L x 1-1/4" W x 2" H Compatible with Whirlpool, Kenmore, KitchenAid, Maytag, Amana, Roper, Admiral, Estate, Crosley, Inglis, and Magic Chef direct-drive washers Replaces all previous coupler versions including 285753, 280152, 285743, and 285140 Aftermarket replacement built to OEM-equivalent quality standards Cost-effective DIY repair — typically under $15 and 30–45 minutes of work Product Specifications Part Number 285753A Part Type Washer Direct Drive Motor Coupler (Motor Coupling Kit) Condition Aftermarket Replacement Application Direct-Drive Top-Load Washers (no belt) Dimensions Approx. 2" L x 1-1/4" W x 2" H Color Black / Off-White Material Rubber / Plastic / Metal (metal sleeve inserts) Kit Includes 2 plastic coupling halves, 1 rubber isolation dampener Compatible Brands Whirlpool, Kenmore, KitchenAid, Maytag, Amana, Roper, Admiral, Estate, Crosley, Inglis, Magic Chef Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting Disconnect power and turn off the water supply before beginning. Remove the washer's cabinet by releasing the top panel clips and removing the front panel screws — the motor and transmission are at the bottom of the machine. The motor coupler is a three-piece assembly between the motor shaft and the transmission input shaft. Pull the motor forward to release it from the mounting clips. The broken coupler pieces will likely fall out at this point — inspect the motor shaft and transmission shaft for any remaining plastic debris and clear it. Press the new rubber dampener onto the motor shaft coupling half first, then onto the transmission shaft coupling half, and snap the motor back into the mounting clips. Verify both coupler halves are seated securely and the rubber dampener is centered between them. Reassemble the front panel and top panel. Restore power and run a short cycle to confirm the agitator and spin function normally. Work gloves recommended — sharp sheet metal edges inside the cabinet. Tools needed: Phillips screwdriver, 1/4" nut driver, flat-head screwdriver, work gloves. Frequently Asked Questions What does the motor coupler do? The motor coupler is a three-piece assembly — two plastic coupling halves and a rubber dampener — that connects the drive motor shaft to the transmission input shaft in direct-drive washing machines. The motor spins the coupler, which transfers that rotation to the transmission, which in turn drives the agitator and drum. The rubber dampener absorbs shock and vibration between the rigid motor and transmission shafts during direction changes. The coupler is intentionally designed as the weakest link in the drivetrain — if the washer is overloaded or the transmission seizes, the coupler breaks first to protect the far more expensive motor and transmission from damage. My washer fills and drains but won't agitate or spin — is the motor coupler the cause? Yes — this is the classic symptom of a broken motor coupler. Because the pump is typically driven directly by the motor before the coupler connection, a broken coupler allows the motor to run and the pump to drain normally, but neither the agitator nor the spin drum receives any power. If you can hear the motor running but nothing moves, open the washer cabinet and inspect the coupler — you will likely find broken plastic pieces at the bottom of the cabinet near the motor and transmission. Why does the motor coupler break? The most common cause is overloading — packing too many heavy items into the washer creates enough mechanical resistance that the coupler snaps rather than allowing the motor to be damaged. Other causes include a worn or seized transmission, a worn motor, normal wear over many years of use, or a single sudden jam caused by a foreign object. If your coupler breaks a second time shortly after replacement, inspect the transmission for signs of wear or binding — a stiff or seized transmission will continue to break new couplers. What is the difference between 285753 and 285753A? The 285753A is the updated current version that superseded the original 285753. The A version incorporates metal sleeve inserts in the plastic coupling halves for improved strength and durability compared to the original all-plastic design. The 285753A replaces all previous versions — including 285753, 280152, 285743, and 285140 — and is the correct part to order regardless of which older number is listed in your washer's parts diagram. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured from rubber, plastic, and metal to match the dimensions and performance of the original 285753A motor coupler. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO DC31-00187A Washer Drain Pump Motor The XPARTCO DC31-00187A is an aftermarket replacement washer drain pump motor compatible with select Samsung front-load and top-load washers in the WA4, WA5, WF2, WF3, WF4, and WF5 series, as well as select Kenmore washers built on the Samsung platform. The drain pump motor drives the impeller that expels water from the washer tub during the drain phase of each wash cycle. When the motor fails, the washer will not drain, will leave standing water in the tub, stop mid-cycle, or display error codes 5C, SE, SC, 5E, or SUDS. This motor-only assembly includes the pump motor, impeller, and replacement O-ring. Rated 120V, 60Hz, 80W, 1.1A (CL.F), with a 30-minute on / 30-minute off duty cycle. Dimensions: 4-1/4"L x 3"W x 4-1/4"H in gray/white/black plastic, metal, and rubber housing. The DC31-00187A is the motor component that installs into the existing pump housing on compatible Samsung washers — the pump housing (DC97-20621C assembly) is reused from the old pump, making this a motor-only swap rather than a complete pump replacement. It directly replaces DC31-00187D, DC31-00178A, DC31-00178D, PX3516-01, 03DC3100187A, 4958525, AP6977256, EAP9605762, PD00056512, PS9605762, and PS1274262. Installs in 20–30 minutes with basic hand tools. Quick Answer The XPARTCO DC31-00187A Washer Drain Pump Motor fixes Samsung front-load and top-load washers displaying error codes 5C, SE, SC, 5E, or SUDS, not draining, leaving standing water, or making loud noise during the drain cycle. Motor-only assembly — includes motor, impeller, and O-ring; installs into existing pump housing. 120V/60Hz/80W/1.1A/CL.F. 30 min on/30 min off. 4-1/4"L x 3"W x 4-1/4"H. Replaces DC31-00187D, DC31-00178A, DC31-00178D, PX3516-01, 4958525, AP6977256, PS9605762. Compatible with Samsung WA4/WA5/WF2/WF3/WF4/WF5 series. Common Problems This Part Fixes Washer not draining — standing water remaining in the tub after a cycle Error codes 5C, SE, SC, 5E, or SUDS displayed — drain fault detected Washer stopping mid-cycle due to a drain fault Loud humming during the drain phase — motor energized but impeller not turning Grinding or rattling during drain — damaged impeller or worn motor bearings Clothes excessively wet after a cycle — pump not fully removing water before spin Water draining very slowly — motor weakening below rated performance Replaces Part Numbers This drain pump motor directly replaces the following OEM and cross-reference part numbers: DC31-00187A, DC31-00178A, DC31-00178D, 03DC3100187A, ASM654116, EAP9605762, 4958525, AP6977256, PD00056512, PS12742622, PX3516-01. If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This drain pump motor is compatible with select Samsung front-load and top-load washers from the following series: Samsung top-load washers — WA4 series (WA40J3000AW, WA44A3205AW, WA45H7000AW, WA45M7050AW, WA45N3050AW, WA45T3200AW, WA45R6100AC and related models) Samsung top-load washers — WA5 series (WA50F9A6DSW, WA50M7450AW, WA50R5200AW, WA50R5400AV and related models) Samsung front-load washers — WF2 series (select models) Samsung front-load washers — WF3 series (select models) Samsung front-load washers — WF4 series (WF42H5000AW, WF42H5200AW, WF45M5500AW, WF45N5300AW, WF45R6100AC, WF45T6000AW, WF45A6400AV, WF45B6300AP and related models) Samsung front-load washers — WF5 series (select models) Kenmore / Sears washers (select Samsung-built models) Note: The DC31-00187A is the pump motor only — it installs into the existing pump housing (DC97-20621C assembly) which is retained from the old pump. The housing is not replaced. Check and clean the drain filter before replacing the pump motor — a clogged filter is a common cause of drain errors that doesn't require motor replacement. Key Features Pump motor only — includes motor, impeller, and O-ring; installs into the existing DC97-20621C pump housing retained from the old pump Drives the pump impeller to expel water from the washer tub during the drain cycle Resolves Samsung error codes 5C, SE, SC, 5E, and SUDS caused by drain pump motor failure Rated 120V, 60Hz, 80W, 1.1A (CL.F) — correct specifications for compatible Samsung washers Duty cycle: 30 minutes on / 30 minutes off Dimensions: 4-1/4"L x 3"W x 4-1/4"H Replaces DC31-00187D, DC31-00178A, DC31-00178D, PX3516-01, 4958525, AP6977256, PS9605762, and PS1274262 Compatible with Samsung WA4, WA5, WF2, WF3, WF4, WF5 series and Kenmore Samsung-built washers Aftermarket replacement built to OEM-equivalent quality standards DIY repair — installs in 20–30 minutes with basic hand tools Product Specifications Part Number XPDC31-00187A Also Covers DC31-00187D, DC31-00178A, DC31-00178D (variants) Part Type Washer Drain Pump Motor (Motor Only — reuses existing housing) Condition Aftermarket Replacement Application Samsung Front-Load and Top-Load Washers (WA4/WA5/WF2/WF3/WF4/WF5) Voltage 120V AC Frequency 60 Hz Wattage 80W Amperage 1.1A Duty Class CL.F Duty Cycle 30 minutes on / 30 minutes off Dimensions 4-1/4"L x 3"W x 4-1/4"H Color Gray / White / Black Material Plastic / Metal / Rubber Includes Pump motor, impeller, O-ring Error Codes Resolved 5C, SE, SC, 5E, SUDS Compatible Brands Samsung, Kenmore (Samsung-built) Installation Notes ⚠️ Unplug Washer and Shut Off Water Before Starting — Wear Gloves Disconnect power and turn off the water supply before beginning. Wear work gloves — there are sharp edges inside the washer cabinet. For front-load models: remove the lower front access panel to expose the pump housing and filter. Drain residual water via the filter drain hose (have a shallow pan ready). Disconnect the wire harness from the motor. On most Samsung front-load models, the motor assembly twists out of the pump housing by rotating counter-clockwise — do not force it. Remove the old motor, note the O-ring position, and install the new O-ring from this kit onto the new DC31-00187A motor. Insert the new motor into the housing and twist clockwise to lock. Reconnect the wire harness. Reinstall the lower panel, restore power and water, and run a drain/spin cycle to confirm drainage. For top-load models: access through the lower front panel or by tilting the washer on its side depending on model. Tools needed: Phillips screwdriver, pliers, shallow pan, towels, work gloves. Frequently Asked Questions What is the difference between DC31-00187A and DC97-20621C? The DC31-00187A is the drain pump motor — the electrical component that drives the impeller. The DC97-20621C is the complete drain pump assembly, which includes the motor plus the outer pump housing, hose connection ports, and mounting hardware. When you order the DC31-00187A, you replace only the motor and reuse the existing DC97-20621C pump housing. When you order the DC97-20621C, you replace the entire assembly including the housing. Both resolve the same drain fault — the DC31-00187A is the more targeted repair when the housing is in good condition. What error codes indicate a drain pump motor failure? Error codes 5C, SE, SC, 5E, and SUDS on compatible Samsung washers all indicate a drain fault — the washer was unable to drain within the expected time. Before replacing the motor, clean the drain filter/coin trap at the lower front panel. A clogged filter is one of the most common causes of these error codes and does not require motor replacement. If the filter is clear and the codes persist, or if the pump is making loud noise or is completely silent during the drain phase, the motor needs replacement. What is the difference between DC31-00187A and DC31-00178A? These are cross-references for the same or very similar Samsung drain pump motor used across different Samsung washer generations. The DC31-00178A was used on earlier Samsung models and the DC31-00187A is the current version. Both are commonly listed as interchangeable replacements for each other in Samsung washer drain pump repair. The DC31-00187D and DC31-00178D are also variants of the same motor from different production runs. Should I clean the filter before replacing the pump motor? Yes — always check and clean the drain filter first. On Samsung front-load washers, the filter is accessible behind the lower front kick panel, typically on the right side — remove the cap slowly and drain water into a shallow pan first. Lint, coins, debris, and hair are very common causes of Samsung drain error codes that are completely resolved by cleaning the filter without any parts replacement. If the filter is clear and the error codes persist, the pump motor is the next component to replace. Is this an OEM or aftermarket part? This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Samsung OEM part, but is manufactured to match the electrical specifications and performance of the original DC31-00187A drain pump motor. Shop With Confidence A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase. ✓ Fast US Shipping ✓ Quality Aftermarket Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO W10810403 (OE) Washer Lid Switch Assembly – Compatible with Whirlpool, Kenmore, Maytag, Crosley, Roper, Amana Washers Product Description Keep your washer running safely and reliably with the XPARTCO W10810403 Washer Lid Switch Assembly. This replacement part ensures the washer only operates when the lid is securely closed, preventing unsafe operation. A faulty lid switch can cause your washer to not start, stop mid-cycle, or fail to drain. Replacing it with this high-quality part restores dependable performance. What is OE ?:  “OE” (Original Equipment) parts are built to the same specifications, materials, and performance standards as the original factory parts. They offer identical fit and function to OEM (Original Equipment Manufacturer) components but are typically sold under independent brands like XPARTCO for better affordability. Replaces Part Numbers W10810403, 4283179, W10648012, W10787878, W10810403VP, PD00028176, EAP11722981, AP5984435, PS11722981. Compatibility This washer lid switch assembly is compatible with select Whirlpool, Kenmore, Maytag, Crosley, Roper, and Amana top-load washers. Example compatible models include (but are not limited to): Whirlpool WTW4800BQ1, Kenmore 110.20222511, and Maytag MVWC415EW1. Always verify your washer’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Broad Compatibility – Fits Whirlpool, Kenmore, Maytag, Crosley, Roper, Amana top-load washers 🔒 Safe Operation – Ensures washer won’t run with lid open 💰 Cost-Effective Alternative – OEM-equivalent performance at a lower price 🛠️ Easy Installation – Only requires a Phillips screwdriver, installs in 10–20 minutes 🛡️ Fixes Common Issues – Resolves washers not starting, stopping mid-cycle, or failing to drain 📐 Product Specification Part Number: W10810403 Component Type: Washer Lid Switch Assembly Material: High-durability plastic + electrical connectors Mounting: Direct replacement, top panel mount Operating Conditions: Designed for standard residential washer use Compliance: OEM-equivalent quality standards 🛠️ Installation Notes Tools Needed: Phillips screwdriver, flathead screwdriver ⚠️ Safety First: Always unplug the washer before starting repairs to avoid electrical shock. Steps: Unplug washer and locate lid switch under the top panel. Remove screws securing the control panel and release clips. Disconnect the wire harness from the old switch. Remove the old switch and install the new one in its place. Reconnect wiring, secure panel, and test the washer. ⏱️ Time Required: 10–20 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders 🛠️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Restore your washer’s performance today — Add to Cart Now for a safe, budget-friendly fix!

Read more less

80040 Washer Agitator Dogs – Compatible with Whirlpool, Kenmore, Maytag, Roper, and Crosley Washers Product Description Restore your washer’s cleaning performance with the 80040 Washer Agitator Dogs. These Washer Agitator Dog set is a set of 4 replacement parts for select Kenmore, Maytag, roper, Whirlpool washing machine models. These are the little plastic cams that allow the top of your agitator to spin freely in one direction but keep it from spinning in the opposite direction, giving you a "ratcheting" effect. If they are worn out, the top of your agitator will spin freely in both directions and your clothes won't get fully washed. Replaces Part Numbers 80040, 285612, 285770, 3109, 3366877, 387091, 80040VP, 99989668, AH388034, EA388034, LP338, EAP388034, PD00002340, AP3119063, PS388034, TJ90LP338. Compatibility This replacement agitator dog kit fits select Whirlpool, Kenmore, Maytag, Roper, Estate, Crosley, and Amana top-load washers. Example compatible models include (but are not limited to): Whirlpool WTW4800XQ2, Kenmore 110.82980100, and Maytag MVWC415EW1. Always verify your washer’s model number before ordering. Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Designed to match OEM performance for Whirlpool-brand washers ⚙️ Restores Wash Action – Replaces worn agitator dogs for proper rotation and cleaning power 💪 Durable Nylon Design – Built for long-lasting use under heavy wash loads 🛠️ DIY Friendly – Installs easily with a socket wrench in minutes 🛡️ Fixes Common Issues – Solves slow or non-spinning upper agitator problems 📐 Product Specification Part Number: 80040 Component Type: Washer Agitator Dogs (Set of 4) Material: High-strength nylon Mounting: Fits inside upper agitator cam assembly Operating Conditions: Designed for top-load washers with dual agitators Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: 7/16-inch socket wrench, flathead screwdriver ⚠️ Safety First: Always unplug the washer before performing repairs to avoid electrical shock. Steps: Unplug the washer and remove the fabric softener dispenser and agitator cap. Use a socket wrench to remove the bolt securing the agitator. Lift off the upper agitator and remove the old agitator dogs. Insert four new 80040 agitator dogs into the slots of the cam assembly. Reassemble the agitator, tighten the bolt, and reinstall the dispenser cap. ⏱️ Time Required: 10–15 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders 🧰 Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Restore strong wash performance — Add to Cart Now for a reliable, budget-friendly replacement!

Read more less

XPARTCO W11220230 Washer Water Inlet Valve The XPARTCO W11220230 is an aftermarket replacement washer water inlet valve designed to control the flow of hot and cold water into your washing machine during each cycle. This Water Inlet Valve is a replacement part compatible with specific Maytag, Whirlpool washing machine models. This valve controls water flow into the tub by opening at predetermined points in the cycle. Proper water regulation is necessary for optimum cleaning performance.. Over time, inlet valves can fail due to mineral buildup, electrical issues, or worn internal seals — leading to slow filling, no fill, or continuous water flow. Replacing the valve restores proper water control and helps prevent leaks or cycle errors. Quick Answer The XPARTCO W11220230 Washer Water Valve fixes washers that won’t fill, fill too slowly, or won’t stop filling with water. It controls incoming water flow and restores proper wash cycle operation. Common Problems This Part Fixes Washer not filling with water Slow water fill during cycles Water continuously flowing into washer Incorrect water temperature Washer stopping due to fill errors Leaking or stuck inlet valve Replaces Part Numbers This water inlet valve replaces the following part numbers: W11220230, W10853296, 4591408, W10632527, W10758829, W11096268, AWP43504, EAP12349461, PD00042661, AP6329544, PS12349461 If your part number is not listed above, contact our support team before ordering and we will verify compatibility. Compatibility This water valve is compatible with select washers from the following brands: Whirlpool washers Maytag washers Amana washers Kenmore / Sears washers (select models) Always verify your washer’s model number before ordering. Contact our support team if you’re unsure. Key Features Three coil hot and cold water valve. OEM-equivalent fit, performance, and durability Restores proper water fill levels and cycle operation Durable construction resists mineral buildup and wear Prevents leaks and overfilling issues Direct replacement for W11220230 valve assembly Product Specifications Part Number W11220230 Part Type three coil hot and cold water inlet valve. Application Top Load / Front Load Washers Condition Aftermarket Replacement Function Controls Water Flow Compatible Brands Whirlpool, Maytag, Amana, Kenmore Installation Notes ⚠️ Safety First — Disconnect Power & Water Supply Unplug the washer and turn off the water supply before servicing. Remove the rear or top panel to access the inlet valve. Disconnect water hoses and electrical connectors, then remove the mounting screws to replace the valve. Reconnect hoses securely to avoid leaks and test for proper operation after installation. Frequently Asked Questions What does a washer water inlet valve do? It controls the flow of hot and cold water into the washer. When the valve fails, the washer may not fill properly or may overfill. Will this fix a washer that won’t fill? Yes, a faulty inlet valve is one of the most common causes of no-fill or slow-fill issues. Is this an OEM part? This is a high-quality aftermarket replacement built to OEM-equivalent standards for performance and durability. Shop With Confidence A U.S.-based appliance parts retailer specializing in high-quality replacement parts. Fast shipping from our U.S. warehouse and expert support available to help verify compatibility. ✓ Fast US Shipping ✓ Quality Parts ✓ Compatibility Support ✓ Secure Checkout

Read more less

XPARTCO 6501EA1001R Washer Pressure Switch – Compatible with LG & Kenmore Washers Product Description Restore accurate water level control with the XPARTCO 6501EA1001R Washer Pressure Switch. This high-quality aftermarket replacement monitors air pressure from the tub to regulate water fill levels during wash cycles. A faulty pressure switch can cause overfilling, under-filling, continuous filling, or washer error codes. Replacing it with this reliable XPARTCO switch ensures proper water sensing and consistent washer performance. Replaces Part Numbers 6501EA1001R, EBF62754506, 2651052, 5210FA3427J, 6501EA1001C, PD00022947, EAP3529177, AH3529177, EA3529177, AP5204365, OEM20817462, PS3529177. Compatibility This replacement washer pressure switch fits select LG and Kenmore (LG-manufactured) top-load and front-load washers. Example compatible models include (but are not limited to):LG WM2016CW, WM2277HWKenmore 796.40512900, 796.41073310 Always verify your washer’s model number before ordering.Contact our support team if you’re unsure. ✅ Key Features 🔄 Aftermarket Replacement – Designed to match OEM water-level sensing accuracy 💧 Precise Water Control – Regulates fill levels to prevent overfilling or underfilling 🔧 Reliable Pressure Detection – Responds accurately to tub air pressure changes 💰 Cost-Effective Solution – Quality performance without OEM pricing 🛡️ Fixes Common Issues – Solves fill errors, overflow, washer not stopping fill, or cycle faults 📐 Product Specification Part Number: 6501EA1001R Component Type: Washer Pressure / Water Level Switch Voltage: 120V AC Connection Type: Hose barb with electrical terminals Mounting: Control panel or cabinet mounted (model dependent) Compliance: Built to OEM-equivalent quality standards (not OEM) 🛠️ Installation Notes Tools Needed: Phillips screwdriver, pliers ⚠️ Safety First: Unplug the washer before servicing to avoid electrical shock. Steps: Disconnect power and access the washer control panel. Locate the pressure switch and disconnect the air hose. Remove wiring connectors and mounting screws. Install the new XPARTCO 6501EA1001R pressure switch. Reconnect the hose and wiring, then reassemble the panel. Restore power and test water filling operation. ⏱️ Time Required: 15–25 minutes 📦 Shop With Confidence 🚚 Free Shipping on All Orders ⚙️ Trusted Appliance Parts Supplier 🔄 30-Day Return Policy Ensure accurate washer water levels again — Add to Cart Now for a dependable, budget-friendly repair!

Read more less

W11210459 Genuine OEM Washer Water Inlet Valve - Compatible with Whirlpool, Kenmore, Maytag, Amana Product Description Keep your washer running smoothly with the W11210459 Genuine OEM Washer Water Inlet Valve. This Whirlpool-manufactured valve assembly is designed as a replacement for select Whirlpool, Kenmore, Maytag, Amana, and other compatible washing machines. It controls the flow of hot and cold water into the washer during wash and rinse cycles, ensuring proper filling and efficient operation. This part addresses issues like leaking water, slow or no water fill, inconsistent water temperature, or overflow, often caused by a faulty or clogged valve. Note: Includes (1) water inlet valve assembly with two solenoids (hoses and clamps not included). Disconnect power and water supply before installation. Verify compatibility with your washer model. Replaces part numbers: W11210459, W10701459, W10838319, W11038711, 4591321, W10869799, W11025984, PD00042885, EAP12349267, AP6329217, PS12349267.  Compatibility: Compatible with select washer models, including but not limited to: Whirlpool: WTW5000DW1, WTW4816FW2, WTW4616FW2, WTW4815EW1, WTW4816FW1 Kenmore: 110.25132411, 110.22352511 Maytag: MVWC565FW0, MVWC415EW1 Amana: NTW4516FW3 Crosley, Inglis, Roper: Various models (verify with model number) Verify your model number or contact our support team for assistance. Key Features: ✅ Brand and Models Compatibility: Fits select Whirlpool, Kenmore, Maytag, Amana, Crosley, Inglis, and Roper washing machines. 🔧 Specifications: Genuine OEM Whirlpool water inlet valve with two solenoids, 110-120V, 60Hz, standard 3/4" hose fitting inlet. 💪 Reliable Performance: Controls hot and cold water flow for consistent wash and rinse cycles. 🛠️ Easy Installation: Requires screwdriver and pliers; typically installed in 15–30 minutes. 🛡️ Effective Fixes: Resolves leaking, slow or no fill, inconsistent water temperature, or overflow issues. Product Specification Part Number: W11210459 Component Type: Washer water inlet valve assembly Material: Plastic and metal Electrical Specs: 110-120V, 60Hz, two solenoids, standard 3/4" hose fitting inlet, two water outlets. Compliance: UL-listed, Prop 65 warning for California. Installation Notes: Safety First: Disconnect the washer from the power source and water supply before installation. Shop for high-quality appliance parts with a 30-day return policy. Keep your washer running efficiently today! Add to cart now for a reliable fix!

Read more less